Intel Broxton has the same LPSS block than Intel Sunrisepoint so add
Broxton ACPI IDs to the list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The "jd_active" variable needs to be signed for the error handling to
work.
Fixes: 143e5887ae57 ('mfd: arizona: factor out checking of jack detection state')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds the mfd cell info for axp288 power key device.
Signed-off-by: Borun Fu <borun.fu@linux.intel.com>
Signed-off-by: Fei Yang <fei.yang@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The WRSTBI bit (disabled by default but enabled by bootloader), when
set, is responsible for resetting voltages to default values of
certain bucks on falling edge of Warm Reset Input pin from AP.
However on some boards (with S2MPS13) the pin is pulled down so any
suspend will effectively trigger the reset of bucks supplying the power
to the little and big cores. In the same time when resuming, these bucks
must provide voltage greater or equal to voltage before suspend to match
the frequency chosen by cpufreq. If voltage (default value of voltage
after reset) is lower than one set by cpufreq before suspend, then
system will hang during resuming.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are different revisions of the same chipset. For example S2MPS13 has
more than 2 revisions. They differ slightly in regulator constraints.
Print the revision number to easily find which PMIC is used on the board.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In the case of a device tree config the code uses the device ID
from the DT entry to check which codec is required but when storing
the ID into struct arizona it was always using the non-DT SPI device
table to get an ID.
This patch changes the code to store the correct ID into struct arizona.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the use of #ifdefs around each case statement of the chip ID
and type validation switches.
We must ensure that the contained code still compiles to nothing if
support for that codec was not built into the kernel, to prevent
creation of link references to missing functions. So the ifdefs are
replaced with a use of the IS_ENABLED() macro.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The code was using a switch on the code type to execute
one of several mfd_add_devices() calls. We're already
switching on the code type earlier in the function to
select the correct patch function so we can roll selection
of the mfd device table into the same switch.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If the declared codec type doesn't match the detected type
we issue a log message but carry on registering the device,
so a dev_warn() is appropriate rather than a dev_err()
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently runtime_suspend will fully power off the codec if
the jack detection is not enabled. Not all future codecs will
have jack detection so to prepare for these codecs this patch
factors out the check so that it be called as needed in the
existing codec-specific switch cases.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently DCVDD isolation is enabled and disabled for
runtime_suspend and runtime_resume. Future codecs will not
have the isolation control so to prepare for these codecs
this patch factors out the isolation control allowing it to
be called as needed in the existing codec-specific switch cases.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is required since
commit 7e50711993 ("mfd: tps6105x: Use i2c regmap to access registers").
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We were getting build warning about unused variable 'ret'.
The commit c749db571dcf has removed the use of ret but missed removing
the variable which is unused now.
Fixes: c749db571dcf ("mfd: lm3533: Simplify function return logic")
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
rts522a(rts5227s) is derived from rts5227, and mainly same with rts5227.
Add it to file mfd/rts5227.c to support this chip.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Rename get_device_type() to da9062_get_device_type().
This function is only used in this file so make it static.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver depends on ARCH_NOMADIK but there isn't a build dependency
so it's a good idea to allow the driver to always be built when the
COMPILE_TEST option is enabled.
That way, the driver can be built with a config generated by make
allyesconfig and check if a patch would break the build.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Definitions for GPIO registers 8, 9, 10, 11, 12 and 13 are added into
the register header file.
- DA9052_GPIO_8_9_REG 25
- DA9052_GPIO_10_11_REG 26
- DA9052_GPIO_12_13_REG 27
A modification is also made to the MFD core code to define these registers
as readable and writable. The functions for da9052_reg_readable() and
da9052_reg_writeable() have had their case statements altered to include
these new registers.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver supports the new Atmel Flexcom. The Flexcom is a wrapper which
integrates one SPI controller, one I2C controller and one USART. Only one
function can be enabled at a time. This driver selects the function once
for all, when the Flexcom is probed, according to the value of the new
"atmel,flexcom-mode" device tree property.
This driver has chosen to present the Flexcom to the system as a MFD so
the implementation is seamless for the existing Atmel SPI, I2C and USART
drivers.
Also the Flexcom embeds FIFOs: the latest patches of the SPI, I2C and
USART drivers take advantage of this new feature.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The call to kstrtoul() will corrupt memory on 64 bit systems because an
int is 4 bytes and a long is 8.
Also it's not a good idea to let users trigger a dev_err() because it
just ends up flooding /var/log/messages so I removed the printk.
Fixes: 2ddd2086ea9c ('mfd: add Intel Broxton Whiskey Cove PMIC driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The invoked functions already return zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The invoked functions already return zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The invoked function already returns zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The invoked functions already return zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The invoked functions already return zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ret variable is not needed since is not used in the
function. Remove the variable and just return 0 instead.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ret variable is not needed since is not used in the
function. Remove the variable and just return 0 instead.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ret variable is not needed since is not used in the
function. Remove the variable and just return 0 instead.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
tps6105 driver provides two cells. One is for GPIO and another one is
for selected mode depending on platform data. When tps6105x is used in
GPIO-only mode, this driver calls mfd_add_devices() with mfd_cell
.name == NULL. This value causes an oops in platform_device_register()
later.
The following patch adds a mfd_cell for each possible mode thereby
excluding .name assignment in runtime.
Signed-off-by: Denis Grigoryev <grigoryev@fastwel.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver handles wakeup irq correctly using irq_set_irq_wake. There's
no need to use IRQF_NO_SUSPEND while registering the interrupt.
This patch removes the use of IRQF_NO_SUSPEND flag.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The lpc_ich_cells array gives the wrong impression about the
relationship between the watchdog and GPIO devices. They are
completely distinct devices, so this patch separates the
array into distinct mfd_cell structs per device.
A side effect of removing the array, is that the lpc_cells enum
is no longer needed.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add MFD core driver for Intel Broxton Whiskey Cove PMIC,
which is specially accessed by hardware IPC, not a generic
I2C device
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver has a I2C device id table that is used to create the module
aliases which already contains a "rt5033". So the alias is not needed.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver has a I2C device id table that is used to create the module
aliases and also "bcm590xx" isn't a supported I2C id, so it's never used.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add tps65217 battery charger subdevice.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove defaults for a bunch of volatile registers and remove
ARIZONA_CTRL_IF_SPI_CFG_1 from the readable list since it doesn't exist
on wm8998 which is I2C only.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some Arizona devices have a hardware ANC block present. This patch adds
the registers necessary to configure this hardware block.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The type of the data for the main Arizona IRQ chip should be struct
arizona not struct regmap_irq_chip_data. The bug is harmless but should
probably be corrected anyway.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver always checks for pdata being NULL except in one place.
Add a check to prevent a possible NULL pointer deference error.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On Odroid XU3 board (with S2MPS11 PMIC) the PWRHOLD bit in CTRL1
register must be manually set to 0 before initiating power off sequence.
One of usual power down methods for Exynos based devices looks like:
1. PWRHOLD pin of PMIC is connected to PSHOLD of Exynos SoC.
2. Exynos holds up this pin during system operation.
3. ACOKB pin of PMIC is pulled up to VBATT and optionally to pin in
other device.
4. When PWRHOLD/PSHOLD goes low, the PMIC will turn off the power if
ACOKB goes high.
On Odroid XU3 family the difference is in (3) - the ACOKB is grounded.
This means that PMIC must manually set PWRHOLD field to low and then
wait for signal from Application Processor (the usual change in
PWRHOLD/PSHOLD pin will actually cut off the power).
The patch adds respective binding allowing Odroid XU3 device to be
powered off.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reported-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are already helper functions to do 64-bit I/O on 32-bit machines, thus we
don't need to reinvent the wheel. In our case we can't use readq() / writeq()
even on 64-bit kernel since there is a hardware limitation (OCP bus is a 32-bit
bus).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Introduced by:
commit 8019ff6cfc ("regmap: Use reg_sequence for multi_reg_write / register_patch")
Interacting with:
commit 561629755a21 ("mfd: arizona: Add support for WM8998 and WM1814")
commit 81207880ce ("mfd: wm5110: Add register patch for rev E and above")
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On the STMPE2401 and STMPE2401 altfunction 1 corresponds to the
PWM channels. This oneliner was missing in the case-switch, making
it impossible to enable the PWM channel output.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 68bab8662f ("mfd: twl6040: Optional clk32k clock handling")
added clock handling for the 32k clock from palmas-clk. However, that
patch did not consider a typical situation where twl6040 is built-in,
and palmas-clk is a loadable module like we have in omap2plus_defconfig.
If palmas-clk is not loaded before twl6040 probes, we will get a
"clk32k is not handled" warning during booting. This means that any
drivers relying on this clock will mysteriously fail, including
omap5-uevm WLAN and audio.
Note that for WLAN, we probably should also eventually get
the clk32kgaudio for MMC3 directly as that's shared between
audio and WLAN SDIO at least for omap5-uevm. It seems the
WLAN chip cannot get it as otherwise MMC3 won't get properly
probed.
Fixes: 68bab8662f ("mfd: twl6040: Optional clk32k clock handling")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add chip identification support for 88PM860 device
to the pm80x_chip_mapping table.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Documentation/devicetree/bindings/mfd/cros-ec.txt DT binding doc lists
"google,cros-ec-i2c" as a compatible string but the corresponding driver
does not have an OF match table. Add the table to the driver so the I2C
core can do an OF style match.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Mika Westerberg
Dan Carpenter
Borun Fu
Krzysztof Kozlowski
Richard Fitzgerald
Axel Lin
Sudip Mukherjee
Micky Ching
Luis de Bethencourt
Steve Twiss
Cyrille Pitchen
Javier Martinez Canillas
Grigoryev Denis
Sudeep Holla
Aaron Sierra
Qipeng Zha
Enric Balletbo i Serra
Charles Keepax
Krzysztof Kozlowski
Andy Shevchenko
Luis de Bethencourt
Nariman Poushin
Linus Walleij
Tony Lindgren
Vaibhav Hiremath
Lee Jones