Implement irq_chip->irq_get_irqchip_state to make it possible for PMIC
block drivers to access the IRQ real time status bits. The status bits
are used for various kinds of input signals, e.g. GPIO.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some HLCDC registers cannot be written until the hardware has finished
applying the previous configuration request. If they are written while
an action is still in progress, the new configuration might be silently
ignored, resulting in unpredictable behavior.
Hide the config synchronization stuff in a regmap implementation and use
this implementation instead of the generic mmio one.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix a missing DVC_RDY interrupt mask in struct regmap_irq definition.
The original submission of this driver did not contain all interrupt
masking definitions in the struct regmap_irq contained in the file
da9063-irq.c
The solution is to add a DA9063_IRQ_DVC_RDY entry to enum da9063_irqs
list and to add the corresponding values to compensate for the missing
mask bit in the static const struct regmap_irq da9063_irqs[] table.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Adam Ward <adam.ward.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The axp152 is a stripped down version of the axp202 pmic with the battery
charging function removed as it is intended for top-set boxes.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds the DMI system ID of the Kontron COMe-bBL6 and COME-cBW6
boards to the Kontron PLD driver. The list of supported products in the
module description is also updated.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Acked-by: Christian Rauch <christian.rauch@kontron.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Qualcomm Debug Subsystem clock is used by CoreSight components.
Add required definitions for it. qcom_rpm_resource::status_id is
not used by driver, so just mark it as ~0.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These reg_default tables are not modified after initialized, so make them
const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap register definitions have been a source of many small fixes
as issues are discovered. As such I made a small automated tool to
check these definitions. This patch fixes the issues (mostly harmless)
located by that tool, the issues fall into three catagories:
1) Volatile registers that have a default in the defaults table (default
has been removed from the table since it is redundant)
2) Registers that are marked as volatile but unreadable (register has
been removed from the volatile list since it is obviously not being
used)
3) Registers that arn't readable but have an entry in the defaults
table (again removed since it is redundant)
4) Readable non-volatile registers that are missing a default, these are
dangerous as they won't get synced during a cache sync. Fortunately,
most of them seem to be registers that shouldn't be there (for example
wm5102 had readable registers for DRC2 and ISRC3 which is doesn't have)
Hopefully another tool will be produced to check the actual default
values themselves but that is outside the scope of this patch.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
o Making pdata NULL check to (!pdata) as coding standard
and all other checks in file.
o Removing redundant check of pdata, because we already
check for pdata, and also derefernced before this check.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ChromeOS EC SPI transport driver has a dependency on OF because it
uses some OF helpers from the <linux/of.h> header. But there isn't a
need for an explicit dependency since the header has stub functions if
CONFIG_OF is not defined.
Also, MFD_CROS_EC_SPI already depends on MFD_CROS_EC which in turn has
a dependency on OF so in practice can't be selected without CONFIG_OF.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The function arizona_irq_thread (the threaded handler for the arizona
IRQs) calls pm_runtime_get_sync at the start to ensure that the chip is
active as we handle the IRQ. If the chip is part way through a runtime
suspend when an IRQ arrives the PM core will wait for the suspend to
complete, before resuming. However, since commit 4f0216409f7c
("mfd: arizona: Add better support for system suspend") the runtime
suspend function may call disable_irq, if the chip is going to fully
power off, which will try to wait for any outstanding IRQs to complete.
This results in deadlock as the IRQ thread is waiting for the PM
operation to complete and the PM thread is waiting for the IRQ to
complete.
To avoid this situation we use disable_irq_nosync, which allows the
suspending thread to finish the suspend without waiting for the IRQ to
complete. This is safe because if an IRQ is being processed it can only
be blocked at the pm_runtime_get_sync at the start of the handler
otherwise it wouldn't be possible to suspend.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify the ACPI device ID array, it doesn't need to be writable at
runtime.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Sunrisepoint (Skylake PCH) has the iTCO watchdog accessible across
the SMBus, unlike previous generations of PCH/ICH where it was on the
LPC bus. Because it's on the SMBus, it doesn't make sense to pass around
a 'struct lpc_ich_info', and leaking the type of bus into the iTCO
watchdog driver is kind of backwards anyway.
This change introduces a new 'struct itco_wdt_platform_data' for use
inside the iTCO watchdog driver and by the upcoming Intel Sunrisepoint
code, which neatly avoids having to include lpc_ich headers in the i801
i2c driver.
This change is overdue because lpc_ich_info has already found its way
into other TCO watchdog users, notably the intel_pmc_ipc driver where
the watchdog actually isn't on the LPC bus as far as I can see.
A simple translation layer is provided for converting from the existing
'struct lpc_ich_info' inside the lpc_ich mfd driver.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Acked-by: Darren Hart <dvhart@linux.intel.com> [drivers/x86 refactoring]
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Fix runtime PM issues on Arizona
- Fix IRQ/Suspend race on Arizona
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/Rnq
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
- fix dependency issues on ChromeOS platforms
- fix runtime PM issues on Arizona
- fix IRQ/suspend race on Arizona
* tag 'mfd-fixes-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: Remove MFD_CROS_EC_SPI depends on OF
platform/chrome: Don't make CHROME_PLATFORMS depends on X86 || ARM
mfd: arizona: Fix initialisation of the PM runtime
mfd: arizona: Fix race between runtime suspend and IRQs
The twl4030 usb phy needs to be active while we are using
the USB VBUS as a current source for charging.
In particular, the usb3v1 regulator must be enabled and the
PHY_PWR_PHYPWD bit must be set to keep the phy powered.
commit ab37813f40
twl4030_charger: Allow charger to control the regulator that feeds it
gave the charger control over the regulator, but didn't resolve
the PHY_PWR_PHYPWD issue.
Now that both of these are controlled by runtime_pm in
phy-twl4030-usb, we can simply take a runtime_pm reference to the USB
phy whenever the charger wants to use it as a current source.
So this patch reverts the above commit, and adds the necessary
runtime_pm calls.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The new coming Intel platforms such as Skylake will contain Sunrisepoint PCH.
The main difference to the previous platforms is that the LPSS devices are
compound devices where usually main (SPI, HSUART, or I2C) and DMA IPs are
present.
This patch brings the driver for such devices found on Sunrisepoint PCH.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The newly introduced device_for_each_child_reverse() would be used when MFD
core removes the device.
After this patch applied the devices will be removed in a reversed order. This
behaviour is useful when devices have implicit dependency on order, i.e.
consider MFD device with serial bus controller, such as SPI, and DMA IP that is
attached to serial bus controller: before remove the DMA driver we have to be
ensured that no DMA transfers is ongoing and the requested channel are unused.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ChromeOS EC SPI transport driver has a dependency on OF because it
uses some OF helpers from the <linux/of.h> header. But there isn't a
need for an explicit dependency since the header has stub functions if
CONFIG_OF is not defined.
Also, MFD_CROS_EC_SPI already depends on MFD_CROS_EC which in turn has
a dependency on OF so in practice can't be selected without CONFIG_OF.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The PM runtime core by default assumes a chip is suspended when runtime
PM is enabled. Currently the arizona driver enables runtime PM when the
chip is fully active and then disables the DCVDD regulator at the end of
arizona_dev_init. This however has several problems, firstly the if we
reach the end of arizona_dev_init, we did not properly follow all the
proceedures for shutting down the chip, and most notably we never marked
the chip as cache only so any writes occurring between then and the next
PM runtime resume will be lost. Secondly, if we are already resumed when
we reach the end of dev_init, then at best we get unbalanced regulator
enable/disables at work we lose DCVDD whilst we need it.
Additionally, since the commit 4f0216409f7c ("mfd: arizona: Add better
support for system suspend"), the PM runtime operations may
disable/enable the IRQ, so the IRQs must now be enabled before we call
any PM operations.
This patch adds a call to pm_runtime_set_active to inform the PM core
that the device is starting up active and moves the PM enabling to
around the IRQ initialisation to avoid any PM callbacks happening until
the IRQs are initialised.
Cc: stable@vger.kernel.org # v3.5+
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The function arizona_irq_thread (the threaded handler for the arizona
IRQs) calls pm_runtime_get_sync at the start to ensure that the chip is
active as we handle the IRQ. If the chip is part way through a runtime
suspend when an IRQ arrives the PM core will wait for the suspend to
complete, before resuming. However, since commit 4f0216409f7c
("mfd: arizona: Add better support for system suspend") the runtime
suspend function may call disable_irq, if the chip is going to fully
power off, which will try to wait for any outstanding IRQs to complete.
This results in deadlock as the IRQ thread is waiting for the PM
operation to complete and the PM thread is waiting for the IRQ to
complete.
To avoid this situation we use disable_irq_nosync, which allows the
suspending thread to finish the suspend without waiting for the IRQ to
complete. This is safe because if an IRQ is being processed it can only
be blocked at the pm_runtime_get_sync at the start of the handler
otherwise it wouldn't be possible to suspend.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is needed as the CRC PMIC has support for Panel
enable/diable as gpio which needs 'gpiod_add_lookup_table'
and 'gpiod_remove_lookup_table' from gpiolib. This patch
can be squashed with below commit in topic/crc-pmic branch
commit 61dd2ca2d4
Author: Shobhit Kumar <shobhit.kumar@intel.com>
Date: Fri Jun 26 14:32:05 2015 +0530
mfd: intel_soc_pmic_core: Add lookup table for Panel Control as GPIO
signal
On some Intel SoC platforms, the panel enable/disable signals
are controlled by CRC PMIC. Add those control as a new GPIO in a
lookup table for gpio-crystalcove chip during CRC driver load
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On some BYT PLatform the PWM is controlled using CRC PMIC. Add a lookup
entry for the same to be used by the consumer (Intel GFX)
CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Needed for PWM control suuported by the PMIC
CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On some Intel SoC platforms, the panel enable/disable signals are
controlled by CRC PMIC. Add those control as a new GPIO in a lookup
table for gpio-crystalcove chip during CRC driver load
CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Switch to my kernel.org alias instead of a badly named gmail address,
which I rarely use.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to allow us to start adding extra annotations for sequences
without bloating register default tables duplicate the structure under
the new name reg_sequence and update the APIs to use that instead of
reg_default.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEbBAABAgAGBQJVqUFGAAoJECTWi3JdVIfQ3YUH+LWLxVerlyUj/uug4vhRLlp2
KkKLInX1r9Al8cRWo6ln3kdB8jTmOxFxm1XUkpz+IQLiF0yV5kGtVm7uBup/X4DA
5oi7313rPs4maS/jqwyuOUi8X+ZMkKxp1Pgf4dJAzRJPN5tlks3drYdqY2c7JdT0
q5IqUR1KIsouK1/wCBy17BEe9PLpjV6U/yN2E/b1tsW1utjtAgY5pPjv/MZpPJ8C
NI6WXHjdykIi6Peg1mHqczgGEkyRlKBllZVsOvFhX1yjy0ITvao5/Mpv8NK5BwwU
cOWPVLlXOwa4m+kVXePPgA4GlB2q1Xupw5k6TDPip5aCGUgS+ryKQmOVcNaJnA==
=C5/o
-----END PGP SIGNATURE-----
Merge tag 'regmap-seq-delay-api' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into asoc-wm5110
regmap: Create a new struct reg_sequence for register sequences
In order to allow us to start adding extra annotations for sequences
without bloating register default tables duplicate the structure under
the new name reg_sequence and update the APIs to use that instead of
reg_default.
Separate the functionality using sequences of register writes from the
functions that take register defaults. This change renames the arguments
in order to support the extension of reg_sequence to take an optional
delay to be applied after any given register in a sequence is written.
This avoids adding an int to all register defaults, which could
substantially increase memory usage for regmaps with large default tables.
This also updates all the clients of multi_reg_write/register_patch.
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch to the same definition of state container as in MAX77693 drivers.
This will allow usage of one regulator driver in both devices: MAX77693
and MAX77843.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This prepares for merging some of the drivers between max77693 and
max77843 so the child MFD driver can be attached to any parent MFD main
driver.
Move the state container to common header file. Additionally add
consistent 'i2c' prefixes to its members (of 'struct i2c_client' type).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a register patch for rev E and above that configures the location of
some write sequences to assist with the headphone enables.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This register will be needed as part of some additional support for the
headphone path on wm5110, so this patch adds the register and sets up
its regmap config.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull irq fixes from Thomas Gleixner:
"This contains:
- a series of fixes for interrupt drivers to prevent a potential race
when installing a chained interrupt handler
- a fix for cpumask pointer misuse
- a fix for using the wrong interrupt number from struct irq_data
- removal of unused code and outdated comments
- a few new helper functions which allow us to cleanup the interrupt
handling code further in 4.3
I decided against doing the cleanup at the end of this merge window
and rather do the preparatory steps for 4.3, so we can run the final
ABI change at the end of the 4.3 merge window with less risk"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
ARM/LPC32xx: Use irq not hwirq for __irq_set_handler_locked()
genirq: Implement irq_set_handler_locked()/irq_set_chip_handler_name_locked()
genirq: Introduce helper irq_desc_get_irq()
genirq: Remove irq_node()
genirq: Clean up outdated comments related to include/linux/irqdesc.h
mn10300: Fix incorrect use of irq_data->affinity
MIPS/ralink: Fix race in installing chained IRQ handler
MIPS/pci: Fix race in installing chained IRQ handler
MIPS/ath25: Fix race in installing chained IRQ handler
MIPS/ath25: Fix race in installing chained IRQ handler
m68k/psc: Fix race in installing chained IRQ handler
avr32/at32ap: Fix race in installing chained IRQ handler
sh/intc: Fix race in installing chained IRQ handler
sh/intc: Fix potential race in installing chained IRQ handler
pinctrl/sun4i: Fix race in installing chained IRQ handler
pinctrl/samsung: Fix race in installing chained IRQ handler
pinctrl/samsung: Fix race in installing chained IRQ handler
pinctrl/exynos: Fix race in installing chained IRQ handler
pinctrl/st: Fix race in installing chained IRQ handler
pinctrl/adi2: Fix race in installing chained IRQ handler
...
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
|
-irq_set_chained_handler(E1, E3);
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
...
|
-irq_set_chained_handler(E1, E3);
...
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
Provide MT6397 RTC interrupt, base address, and register in
MT6397 MFD.
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- plug a potential race related to chained interrupt handlers
- core updates which address the needs of the x86 irqdomain conversion
- new irqchip callback to support affinity settings for VCPUs
- the usual pile of updates to interrupt chip drivers
- a few helper functions to allow further cleanups and
simplifications
I have a largish pile of coccinelle scripted/verified cleanups and
simplifications pending on top of that, but I prefer to send that
towards the end of the merge window when the arch/driver changes have
hit your tree to avoid API change wreckage as far as possible"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
genirq: Remove bogus restriction in irq_move_mask_irq()
irqchip: atmel-aic5: Add sama5d2 support
irq: spear-shirq: Fix race in installing chained IRQ handler
irq: irq-keystone: Fix race in installing chained IRQ handler
gpio: gpio-tegra: Fix race in installing chained IRQ handler
gpio: gpio-mxs: Fix race in installing chained IRQ handler
gpio: gpio-mxc: Fix race in installing chained IRQ handler
ARM: gemini: Fix race in installing GPIO chained IRQ handler
GPU: ipu: Fix race in installing IPU chained IRQ handler
ARM: sa1100: convert SA11x0 related code to use new chained handler helper
irq: Add irq_set_chained_handler_and_data()
irqchip: exynos-combiner: Save IRQ enable set on suspend
genirq: Introduce helper function irq_data_get_affinity_mask()
genirq: Introduce helper function irq_data_get_node()
genirq: Introduce struct irq_common_data to host shared irq data
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
irqchip: gic: Simplify gic_configure_irq by using IRQCHIP_SET_TYPE_MASKED
irqchip: renesas: intc-irqpin: Improve binding documentation
genirq: Set IRQCHIP_SKIP_SET_WAKE for no_irq_chip
...
Using -1 as platform device id means that the platform driver core will not
assign any id to the device (the device name will not have id at all). This
results problems on systems that have multiple PCHs (Platform Controller
HUBs) because all of them also include their own copy of LPC device.
All the subsequent device creations will fail because there already exists
platform device with the same name.
Fix this by passing PLATFORM_DEVID_AUTO as platform device id. This makes
the platform device core to allocate new ids automatically.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add MFD support for the DA9063 OnKey driver
The function da9063_clear_fault_log() is added to mitigate the case of a
hardware power-cut after a long-long OnKey press. Although there is no
software intervention in this case (by definition) such a shutdown would
cause persistent information within the DA9063 FAULT_LOG that would be
available during the next device restart.
Clearance of this persistent register must be completed after such a
hardware power-cut operation has happened so that the FAULT_LOG does not
continue with previous values. The clearance function has been added here
in the kernel driver because wiping the fault-log cannot be counted on
outside the Linux kernel.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
[Lee: Removed 'key_power' for Dmitry to take through the Input Tree]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The use of ifneq against 'n' to conditionally compile codec-specific
parts is wrong and was resulting in all the codec tables being built
even for deselected codecs.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Current code in mfd-core calls into ACPI to check resources even
on a system that booted with a DT (on kernels with both DT and ACPI
support compiled in). This triggers ACPI exceptions since we may
end up calling the ACPI interpreter when it has not been initialized:
"ACPI Exception: AE_BAD_PARAMETER, Thread 2064154624 could not acquire
Mutex [0x1] (20150410/utmutex-285)"
This patch fixes the issues by adding a check for an ACPI companion
device before carrying out ACPI resources checks to avoid calling
the ACPI interpreter if the fwnode representing the device is an OF one.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Later arizona silicon has the single/differential selector
in a different register, and IN1_MODE only selects between
analogue or digital. Prepare for this by splitting the
INx_MODE definition into two fields.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On the wm5110 it is important the reset line is held for slightly longer
to ensure the device starts up well. This patch adds a 5mS delay for
this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Allow the chip to completely power off if we enter runtime suspend and
there is no jack detection active. This is helpful for systems where
system suspend might remove the supplies to the CODEC, without informing
us. Note the powering off is done in runtime suspend rather than system
suspend, because we need to hold reset until the first time DCVDD is
powered anyway (which would be in runtime resume), and we might as well
save the extra power.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The low power sleep mode on wm5110 requires that the LDO1 regulator be
set to 1.175V prior to entering sleep, then returned to 1.2V after
exiting sleep mode. This patch apply these regulator settings.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some register settings must be applied before the first time low power
sleep mode is entered on the wm5110 to ensure optimium performance.
These settings require SYSCLK to be enabled whilst they are being
applied. This patch applies the settings using the recently factored out
boot time SYSCLK functionality.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
wm5102 applies a custom hardware boot sequence, for this the SYSCLK
needs to be enabled. This patch factors out the code that enables
SYSCLK for this sequence such that it can be used for other boot time
operations that require SYSCLK.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In preparation for some refactoring fixup some minor style, formating
and code clarity issues.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The wm5102 uses a custom boot sequence and the standard boot sequence is
disabled. However, the standard boot sequence must be run at least once
after a cold boot (caused by either a hard reset or removal of AVDD).
Unfortunately the register WRITE_SEQUENCER_CTRL_3 is not affected by the
hardware reset. This means if the device has been previously booted but
the AVDD supply has never been removed, arizona_dev_init will reset the
chip but the boot sequence will not run, which can cause numerous
problems. The solution is to manually clear this register and then boot
the chip again, which is what this patch does.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds functions for enabling and disabling the physical reset
line. This will be helpful in future refactoring.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This also handily fixes a leak of the GPIO in arizona_dev_exit.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
I noticed the PMIC configuration on 37xx-evm won't actually shut down
the voltages during off-idle. Turns out 37xx-evm needs the AC charger
state transitions disabled like we are doing for SDP and LDP in the
legacy booting case.
Let's fix this for device tree based booting by setting up the quirk
flag based on the compatible flag. And let's also use the existing
define for STARTON_CHG.
Note that SDP and EVM do not have the PMIC clken wired to gate the
the oscillator while LDP has.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This soft reset used to be located after the register patch had been
applied, but has since moved to before the patch is applied. At the new
location there is no requirement to do a register sync as no register
writes will have happened yet.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify in various drivers configuration data which is not modified:
- regmap_irq_chip,
- individual regmap_irq's in array,
- regmap_config,
- irq_domain_ops,
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert SA11x0 (Neponset, SA1111, and UCB1x00 code) to use the new
irq_set_chained_handler_and_data() helper.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/E1Z4yzx-0002S6-7p@rmk-PC.arm.linux.org.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some ECs need a little time for waking up before they can accept
SPI data at a high speed. This is configurable via a DT property
"google,cros-ec-spi-pre-delay".
This patch makes the cros_ec_spi driver to cause a delay before
the beginning of a SPI transaction, to make sure that the EC has
already woken up, if the property has been defined in the DTS.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Chromebooks can have more than one Embedded Controller so the
cros_ec device id has to be incremented for each EC registered.
Add a new structure to represent multiple EC as different char
devices (e.g: /dev/cros_ec, /dev/cros_pd). It connects to
cros_ec_device and allows sysfs inferface for cros_pd.
Also reduce number of allocated objects, make chromeos sysfs
class object a static and add refcounting to prevent object
deletion while command is in progress.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add proto v3 support to the SPI, I2C, and LPC.
Signed-off-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support in cros_ec.c to handle EC host command protocol v3.
For v3+, probe for maximum shared protocol version and max
request, response, and passthrough sizes. For now, this will
always fall back to v2, since there is no bus-specific code
for handling proto v3 packets.
Signed-off-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MFD driver should only have the logic to instantiate its child devices
and setup any shared resources that will be used by the subdevices drivers.
The cros_ec MFD is more complex than expected since it also has helpers to
communicate with the EC. So the driver will only get more bigger as other
protocols are supported in the future. So move the communication protocol
helpers to its own driver as drivers/platform/chrome/cros_ec_proto.c.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 1b84f2a4cd ("mfd: cros_ec: Use fixed size arrays to transfer
data with the EC") modified the struct cros_ec_command fields to not
use pointers for the input and output buffers and use fixed length
arrays instead.
This change was made because the cros_ec ioctl API uses that struct
cros_ec_command to allow user-space to send commands to the EC and
to get data from the EC. So using pointers made the API not 64-bit
safe. Unfortunately this approach was not flexible enough for all
the use-cases since there may be a need to send larger commands
on newer versions of the EC command protocol.
So to avoid to choose a constant length that it may be too big for
most commands and thus wasting memory and CPU cycles on copy from
and to user-space or having a size that is too small for some big
commands, use a zero-length array that is both 64-bit safe and
flexible. The same buffer is used for both output and input data
so the maximum of these values should be used to allocate it.
Suggested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If the EC device tree node has sub-nodes, try to instantiate them as
MFD sub-devices. We can configure the EC features provided by the board.
Signed-off-by: Todd Broch <tbroch@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Parent and device were pointing to the same device structure.
Parent is unused, removed.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Stephen Barber <smbarber@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Puthikorn Voravootivat <puthik@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix broken probe of da9052 regulators, which since commit b3f6c73db7
("mfd: da9052-core: Fix platform-device id collision") use a
non-deterministic platform-device id to retrieve static regulator
information. Fortunately, adequate error handling was in place so probe
would simply fail with an error message.
Update the mfd-cell ids to be zero-based and use those to identify the
cells when probing the regulator devices.
Fixes: b3f6c73db7 ("mfd: da9052-core: Fix platform-device id collision")
Cc: stable <stable@vger.kernel.org> # v3.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now that the axp20x-regulators driver supports different variants of the
AXP family, we can enable regulator support for AXP22X without the risk
of incorrectly configuring regulators.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for the AXP22x PMIC devices to the existing AXP20x driver.
This includes the AXP221 and AXP223, which are identical except for
the external data bus. Only AXP221 is added for now. AXP223 will be
added after it's Reduced Serial Bus (RSB) interface is supported.
AXP22x defines a new set of registers, power supplies and regulators,
but most of the API is similar to the AXP20x ones.
A new irq chip definition is used, even though the available interrupts
on AXP22x is a subset of those on AXP20x. This is done so the interrupt
numbers match those on the datasheet.
This patch only enables the interrupts, system power-off function, and PEK
sub-device. The regulator driver must first support different variants
before we enable it from the mfd driver.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[wens@csie.org: fix interrupts and move regulators to separate patch]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In our department we are using some older Janz ICAN3-modules in our dekstop
pcs. There we have slightly different carrier boards than the janz-cmodio
supported in the kernel sources, called CAN-PCI2 with two submodules. But the
pci configuration regions are identical. So extending the supported pci devices
to the corresponding device ids is sufficient to get the drivers working.
* The old ICAN3-modules with firmware 1.28 need more then 250ms for the restart
after reset. I've increased the timeout to 500ms.
* The janz_ican3 module uses the raw can services of the Janz-firmware, this
means firmware must be ICANOS/2. Our ICAN3-modules are equipped with
CAL/CANopen-firmware, so I must use the appropriate commands for the layer
management services.
Te driver detects the firmware after module reset and selects the commands
matching the firmware. This affects the bus on/off-command
(ican3_set_bus_state) and the configuration of the bittiming
(ican3_set_bittiming). For better diagnostics the detected firmware string is
presented as sysfs attribute (fwinfo).
Signed-off-by: Andreas Gröger <andreas24groeger@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Here's a set of updates to the Chrome OS platform drivers for this merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can make your
own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The laptop driver
is trying to be smart and not instantiate the devices that don't answer to
probe. For the trackpad that can come up in two modes (bootloader or regular),
this gets complicated since the driver already knows how to handle the two
modes including the actual addresses used. So now the laptop driver needs to
know more too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few bugfixes
from him, kbuild and myself.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NVa4
-----END PGP SIGNATURE-----
Merge tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform
Pull chrome platform updates from Olof Johansson:
"Here's a set of updates to the Chrome OS platform drivers for this
merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can
make your own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The
laptop driver is trying to be smart and not instantiate the devices
that don't answer to probe. For the trackpad that can come up in
two modes (bootloader or regular), this gets complicated since the
driver already knows how to handle the two modes including the
actual addresses used. So now the laptop driver needs to know more
too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few
bugfixes from him, kbuild and myself"
* tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
platform/chrome: chromeos_laptop - instantiate Atmel at primary address
platform/chrome: cros_ec_lpc - Depend on X86 || COMPILE_TEST
platform/chrome: cros_ec_lpc - Include linux/io.h header file
platform/chrome: fix platform_no_drv_owner.cocci warnings
platform/chrome: cros_ec_lightbar - fix duplicate const warning
platform/chrome: cros_ec_dev - fix Unknown escape '%' warning
platform/chrome: Expose Chrome OS Lightbar to users
platform/chrome: Create sysfs attributes for the ChromeOS EC
mfd: cros_ec: Instantiate ChromeOS EC character device
platform/chrome: Add Chrome OS EC userspace device interface
platform/chrome: Add cros_ec_lpc driver for x86 devices
mfd: cros_ec: Add char dev and virtual dev pointers
mfd: cros_ec: Use fixed size arrays to transfer data with the EC
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
* new API for safe access of power supply function attrs
* devres support for power supply (un)registration
* new drivers / chips
- generic syscon based poweroff driver
- iio & charger driver for da9150
- fuel gauge driver for axp288
- bq27x00: add support for bq27510
- bq2415x: add support for bq24157s
* twl4030-madc-battery: convert to iio consumer
* misc fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WbZu
-----END PGP SIGNATURE-----
Merge tag 'for-v4.1' of git://git.infradead.org/battery-2.6
Pull power supply and reset changes from Sebastian Reichel:
- new API for safe access of power supply function attrs
- devres support for power supply (un)registration
- new drivers / chips:
- generic syscon based poweroff driver
- iio & charger driver for da9150
- fuel gauge driver for axp288
- bq27x00: add support for bq27510
- bq2415x: add support for bq24157s
- twl4030-madc-battery: convert to iio consumer
- misc fixes
* tag 'for-v4.1' of git://git.infradead.org/battery-2.6: (66 commits)
power: twl4030_madc_battery: Add missing MODULE_ALIAS
power: twl4030-madc-battery: Convert to iio consumer.
dt: power: Add docs for generic SYSCON poweroff driver.
power: reset: Add generic SYSCON register mapped poweroff.
power: max17042_battery: add missed blank
power: max17042_battery: Use reg type instead of chip type
power/reset: at91: big endian fixes for atsama5d3x
power_supply: charger-manager: Fix dereferencing of ERR_PTR
HID: input: Fix NULL pointer dereference when power_supply_register fails
power: constify of_device_id array
power/reset/rmobile-reset.c: Fix !HAS_IOMEM build
power_supply: 88pm860x_charger: Fix possible NULL pointer dereference and use of initialized variable
arm: mach-pxa: Decrement the power supply's device reference counter
mfd: ab8500: Decrement the power supply's device reference counter
power_supply: bq2415x_charger: Decrement the power supply's device reference counter
power_supply: 88pm860x_charger: Decrement the power supply's device reference counter
x86/olpc/xo15/sci: Use newly added power_supply_put API
x86/olpc/xo1/sci: Use newly added power_supply_put API
power_supply: charger-manager: Decrement the power supply's device reference counter
power_supply: Increment power supply use counter when obtaining references
...
The RTC on S2MPS11 is the same as S2MPS14. However interrupt numbers of
RTC alarms 0 and 1 were inversed between these two devices. So when
rtc-s5m driver requested S2MPS14_IRQ_RTCA0 interrupt, it matched to
S2MPS11_IRQ_RTCA1, not RTCA0.
Fix this by using consistent RTC alarm interrupt numbers and adding a
BUILD_BUG_ON for future generations.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The earpiece on 5102 is mono, thus there is no output 3R. Remove the
registers associated with the unused right channel from the readable
registers list.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Even if bus is not hot-pluggable, the devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds the mfd cell info for axp288 extcon device.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The patch sorts IDs in the table for easier maintenance. There is no
functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is a I2C driver, so it's wrong to use platform prefix for the
modalias. We have all needed i2c aliases coming form MODULE_DEVICE_TABLE,
so let's remove the wrong and unneeded "platform:twl6040" modalias.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some of the PMIC's could have specific regmap configuration
tables in future, so add specific compatible strings for known
PMIC's. Also print runtime detected chip revision information.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Replace duplicated const keyword for 'axp20x_model_names' with proper
array of const pointers to const strings.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Drop support for SW controlled VCORE, nobody uses it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch just sorts IDs in the table for better maintenance. There is no
functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The IPQ8064 also includes an RPM following the same message structure as
other chips. In addition, it supports a few new resource types to
support the NSS fabric clocks and the SMB208/SMB209 regulators found on
the reference boards.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 6e3f62f079 ("mfd: core: Fix platform-device id
generation") we honour PLATFORM_DEVID_AUTO and PLATFORM_DEVID_NONE when
registering mfd-devices.
Unfortunately, some mfd-drivers rely on the old behaviour of generating
platform-device ids by adding the cell id also to the special value of
PLATFORM_DEVID_NONE. The resulting platform ids are not only used to
generate device-unique names, but are also used instead of the cell id
to identify cells when probing subdevices.
These drivers should be updated to use PLATFORM_DEVID_AUTO, which would
also allow more than one device to be registered without resorting to
hacks (see for example wm831x), but lets fix the regression first by
partially reverting the above mentioned commit with respect to
PLATFORM_DEVID_NONE.
Fixes: 6e3f62f079 ("mfd: core: Fix platform-device id generation")
Cc: stable <stable@vger.kernel.org> # v3.19
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
dmi_get_system_info() may return NULL either when CONFIG_DMI is not set or when
board has an old firmware. The patch prevents a crash and changes the default
frequency to be in align with older board.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[Lee: Removed overt "sentinel" comment and extra lines]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The S2MPS11 PMIC (present on Arndale Octa board) has the same RTC module
as S2MPS14 device. Add respective mfd cell to enable it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Converting milliseconds to jiffies by "val * HZ / 1000" is technically
OK but msecs_to_jiffies(val) is the cleaner solution and handles all
corner cases correctly. This is a minor API consolidation only and
should make things more readable.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All systems using the TC3589x multifunction expander uses
devicetree, so don't clutter the place with a lot of
and assume it is there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use %pS for actual addresses, otherwise you'll get bad output
on arches like ppc64 where %pF expects a function descriptor.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Even if bus is not hot-pluggable, the devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use power_supply_put() to decrement the power supply's device reference
counter.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Replace direct calls to power supply function attributes with wrappers.
Wrappers provide safe access in case of unregistering the power
supply (e.g. by removing the driver). Replace:
- get_property -> power_supply_get_property
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
On success, callback function returns 0. So invert the if condition
check so that we can break out of loop.
Cc: stable@vger.kernel.org
Signed-off-by: Ameya Palande <2ameya@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a DT binding that lets the DMIC reference voltage source be
specified for each input.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Change flash cell identifiers from max77693-flash to max77693-led
to avoid confusion with NOR/NAND Flash.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In Quark X1000, there's a single PCI device that provides both
an I2C controller and a GPIO controller. This MFD driver will
split the 2 devices for their respective drivers.
This patch is based on Josef Ahmad's initial work for Quark enabling.
Acked-by: Michael Turquette <mturquette@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Rk808 has a under voltage detect function, when the voltage of buck is
under 85% the target voltage, the buck output will reset. But if the
power load is too heavy, this function maybe err, when current over
4.2A, although the voltage is normal, but RK808 mistakenly think it is
under 85%, and reset the buck. So let's disable this function.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The seq_printf return value, because it's frequently misused,
will eventually be converted to void.
See: commit 1f33c41c03 ("seq_file: Rename seq_overflow() to
seq_has_overflowed() and make public")
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 0b2712585(linux-next.git) this driver uses regmap_irq and so needs
to select REGMAP_IRQ.
This fixes the following compilation errors:
ERROR: "regmap_irq_get_domain" [drivers/mfd/rt5033.ko] undefined!
ERROR: "regmap_add_irq_chip" [drivers/mfd/rt5033.ko] undefined!
Signed-off-by: Artem Savkov <asavkov@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The range of registers used by this driver exceeds that available
via SPI with no paging (127), so we have to override the values
from the default config which is set-up for I2C access.
Also change SPI settings to match device's recommended OTP values.
Signed-off-by: Adam Ward <adam.ward.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Name changes to the battery cell structure to a
more generic cell type: fuel gauge.
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch adds MAX77843 core/irq driver to support PMIC,
MUIC(Micro USB Interface Controller), Charger, Fuel Gauge,
LED and Haptic device.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds support for the MediaTek MT6397 PMIC. This is a
multifunction device with the following sub modules:
- Regulator
- RTC
- Audio codec
- GPIO
- Clock
It is interfaced to the host controller using SPI interface by a proprietary
hardware called PMIC wrapper or pwrap. MT6397 MFD is a child device of the
pwrap.
Signed-off-by: Flora Fu, MediaTek
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is no need to print additional ENOMEM message for
sec_platform_data allocation failure.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The WTSR (Watchdog Timer Software Reset) and SMPL (Sudden Momentary
Power Loss) were removed from rtc-s5m driver because they were not used.
Remove them (and on/off interrupt) from main MFD driver and header.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
pcr_dbg is a wrapper of dev_dbg, which can save some code,
and help to enable/disable debug message static.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
To enable/disable ASPM we should find LINK CONTROL register
in PCI config space. All old chip use 0x80 address, but new
chip may use another address, so we using pci_find_capability()
to get LINK CONTROL address.
rtsx_gops.c was removed, we consider to put some common operations
to this file, but the actual thing is, only a group of chips
are in common ops1, and another group of chips in common ops2,
it is hard to decide put which ops into generic ops file.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Update some phy register name and value for rts5249,
the updated value makes chip more stable on some platform.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
update card drive settings, This setting can be used for rts5249
rts524A and rts525A.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
PETXCFG is defined at 0xFF03, the old 0xFE49 not used any more.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In one shot mode, sequencer automatically disables all enabled steps at
the end of each cycle. (both ADC steps and TSC steps) Hence these steps
need not be saved in reg_se_cache for clearing these steps at a later
stage.
Also, when ADC wakes up Sequencer should not be busy executing any of the
config steps except for the charge step. Previously charge step was 1 ADC
clock cycle and hence it was ignored.
TSC steps are always disabled at the end of each conversion cycle, hence
there is no need to explicitly disable TSC steps by writing 0 to REG_SE.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now, as all VE platforms have to be booted with DT,
the code handling non-DT case can be removed.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds the DMI system ID of the Kontron COMe-cBL6 board to
the Kontron PLD driver. The list of supported products in the module
description is also updated.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Acked-by: Christian Rauch <christian.rauch@kontron.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Name changes to the battery cell structure to a
more generic cell type: fuel gauge.
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Surely GPIO irq will be used as an input pin so make sure its direction is
set after requesting.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is usually better to pass actual error code from a function call than
mangling it to another.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
intel_soc_pmic_find_gpio_irq() tries to find a GPIO interrupt but doesn't
select between it or I2C interrupt so it makes more sense to move this
comment to intel_soc_pmic_i2c_probe() with minor edits.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ChromeOS EC character device is an user-space interface to
allow applications to access the Embedded Controller.
Add a cell for this device so it's spawned from the mfd driver.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The struct cros_ec_command will be used as an ioctl() argument for the
API to control the ChromeOS EC from user-space. So the data structure
has to be 64-bit safe to make it compatible between 32 and 64 avoiding
the need for a compat ioctl interface. Since pointers are self-aligned
to different byte boundaries, use fixed size arrays instead of pointers
for transferring ingoing and outgoing data with the Embedded Controller.
Also, re-arrange struct members by decreasing alignment requirements to
reduce the needing padding size.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds support for the Wolfson Microelectronics WM8280 and WM8281
codecs.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
[Lee: Minor fixup to remove potentially uninitialised variable. ]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Bjorn Andersson
Boris Brezillon
Steve Twiss
Michal Suchanek
Michael Brunner
Ivan T. Ivanov
Krzysztof Kozlowski
Axel Lin
Charles Keepax
Maninder Singh
Richard Fitzgerald
Javier Martinez Canillas
Mathias Krause
Lee Jones
Matt Fleming
Linus Torvalds
NeilBrown
Rafael J. Wysocki
Andy Shevchenko
Shobhit Kumar
Viresh Kumar
Mark Brown
Nariman Poushin
Krzysztof Kozlowski
Thomas Gleixner
Eddie Huang
Mika Westerberg
Fabio Estevam
Hongzhou Yang
Lorenzo Pieralisi
Geert Uytterhoeven
Tony Lindgren
Russell King
Alexandru M Stan
Gwendal Grignou
Stephen Barber
Todd Broch
David S. Miller
Johan Hovold
Chen-Yu Tsai
Andreas Gröger
Dmitry Torokhov
Ramakrishna Pallala
Ivan T. Ivanov
Aaro Koskinen
Łukasz Stelmach
Josh Cartwright
Fabian Frederick
Nicholas Mc Guire
Linus Walleij
Scott Wood
Ameya Palande
Roger Tseng
Gyungoh Yoo
Jacek Anaszewski
Raymond Tan
Chris Zhong
Joe Perches
Artem Savkov
Adam Ward
Todd Brandt
Masanari Iida
Jaewon Kim
Flora Fu
Micky Ching
Vignesh R
Pawel Moll
Jarkko Nikula