Commit Graph

93 Commits

Author SHA1 Message Date
Dongsheng.wang@freescale.com a63b3bc7db powerpc/fsl: add MPIC timer wakeup support
The driver provides a way to wake up the system by the MPIC timer.

For example,
echo 5 > /sys/devices/system/mpic/timer_wakeup
echo standby > /sys/power/state

After 5 seconds the MPIC timer will generate an interrupt to wake up
the system.

Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
2013-07-01 18:38:42 -05:00
Dongsheng.wang@freescale.com 36ca09be6f powerpc/mpic: add global timer support
The MPIC global timer is a hardware timer inside the Freescale PIC complying
with OpenPIC standard. When the specified interval times out, the hardware
timer generates an interrupt. The driver currently is only tested on fsl chip,
but it can potentially support other global timers complying to OpenPIC
standard.

The two independent groups of global timer on fsl chip, group A and group B,
are identical in their functionality, except that they appear at different
locations within the PIC register map. The hardware timer can be cascaded to
create timers larger than the default 31-bit global timers. Timer cascade
fields allow configuration of up to two 63-bit timers. But These two groups
of timers cannot be cascaded together.

It can be used as a wakeup source for low power modes. It also could be used
as periodical timer for protocols, drivers and etc.

Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2013-07-01 18:38:41 -05:00
Alistair Popple 30650239ad powerpc: Add an in memory udbg console
This patch adds a new udbg early debug console which utilises
statically defined input and output buffers stored within the kernel
BSS. It is primarily designed to assist with bring up of new hardware
which may not have a working console but which has a method of
reading/writing kernel memory.

This version incorporates comments made by Ben H (thanks!).

Changes from v1:
	- Add memory barriers.
	- Ensure updating of read/write positions is atomic.

Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2013-05-08 06:36:49 +10:00
Benjamin Herrenschmidt dffff02a6b Merge remote-tracking branch 'agust/next' into next
<<
Please pull mpc5xxx patches for v3.9. The bestcomm driver is
moved to drivers/dma (so it will be usable for ColdFire).
mpc5121 now provides common dtsi file and existing mpc5121 device
trees use it. There are some minor clock init and sparse fixes
and updates for various 5200 device tree files from Grant. Some
fixes for bugs in the mpc5121 DIU driver are also included here
(Andrew Morton suggested to push them via my mpc5xxx tree).
>>
2013-02-20 11:39:05 +11:00
Anton Blanchard 1fbe9cf259 powerpc: Build kernel with -mcmodel=medium
Finally remove the two level TOC and build with -mcmodel=medium.

Unfortunately we can't build modules with -mcmodel=medium due to
the tricks the kernel module loader plays with percpu data:

# -mcmodel=medium breaks modules because it uses 32bit offsets from
# the TOC pointer to create pointers where possible. Pointers into the
# percpu data area are created by this method.
#
# The kernel module loader relocates the percpu data section from the
# original location (starting with 0xd...) to somewhere in the base
# kernel percpu data space (starting with 0xc...). We need a full
# 64bit relocation for this to work, hence -mcmodel=large.

On older kernels we fall back to the two level TOC (-mminimal-toc)

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2013-01-10 17:00:31 +11:00
Vinh Nguyen Huu Tuong c19d824862 powerpc/44x: Support OCM(On Chip Memory) for APM821xx SoC and Bluestone board
This patch consists of:
- Add driver for OCM component
- Export OCM Information at /sys/kernel/debug/ppc4xx_ocm/info

Signed-off-by: Vinh Nguyen Huu Tuong <vhtnguyen@apm.com>
Acked-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2013-01-10 15:08:37 +11:00
Philippe De Muyter 9a32299394 powerpc, dma: move bestcomm driver from arch/powerpc/sysdev to drivers/dma
The bestcomm dma hardware, and some of its users like the FEC ethernet
component, is used in different FreeScale parts, including non-powerpc
parts like the ColdFire MCF547x & MCF548x families.  Don't keep the
driver hidden in arch/powerpc where it is inaccessible for other arches.
.c files are moved to drivers/dma/bestcomm, while .h files are moved to
include/linux/fsl/bestcomm.  Makefiles, Kconfigs and #include directives
are updated for the new file locations.

Tested by recompiling for MPC5200 with all bestcomm users enabled.

Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2013-01-03 15:41:20 +01:00
Varun Sethi 0a4081641d powerpc/mpic: FSL MPIC error interrupt support.
All SOC device error interrupts are muxed and delivered to the core
as a single MPIC error interrupt. Currently all the device drivers
requiring access to device errors have to register for the MPIC error
interrupt as a shared interrupt.

With this patch we add interrupt demuxing capability in the mpic driver,
allowing device drivers to register for their individual error interrupts.
This is achieved by handling error interrupts in a cascaded fashion.

MPIC error interrupt is handled by the "error_int_handler", which
subsequently demuxes it using the EISR and delivers it to the respective
drivers.

The error interrupt capability is dependent on the MPIC EIMR register,
which was introduced in FSL MPIC version 4.1 (P4080 rev2). So, error
interrupt demuxing capability is dependent on the MPIC version and can
be used for versions >= 4.1.

Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-09-12 14:57:10 -05:00
Jia Hongtao 8626816e90 powerpc: add support for MPIC message register API
Some MPIC implementations contain one or more blocks of message registers
that are used to send messages between cores via IPIs.  A simple API has
been added to access (get/put, read, write, etc ...) these message registers.
The available message registers are initially discovered via nodes in the
device tree.  A separate commit contains a binding for the message register
nodes.

Signed-off-by: Meador Inge <meador_inge@mentor.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16 16:15:28 -05:00
Martyn Welch 44b24b74ab powerpc: Move GE PIC drivers
Move the GE PIC drivers to allow these to be used by non-86xx boards.

Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16 11:08:11 -05:00
Prabhakar Kushwaha a20cbdeffc powerpc/fsl: Add support for Integrated Flash Controller
Integrated Flash Controller supports various flashes like NOR, NAND
and other devices using NOR, NAND and GPCM Machine available on it.
IFC supports four chip selects.

Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Liu Shuo <b35362@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-04 15:41:22 -06:00
Liu Gang 6ec4bedbf1 fsl-rio: Split rio driver into two parts, RapidIO endpoint and message unit
The Freescale PowerPC RapidIO controller consists of a RapidIO endpoint and
a RapidIO message unit(RMU). Or use RapidIO message manager(RMan) to
replace the RMU in DPAA architecture. Therefore, we should split the code
into two function modules according to the hardware architecture. Add new
struct for RMU module, and new initialization function to set up RMU
module. This policy is very conducive to adding new module like RMan, or
adding multi-ports or message units support.

Signed-off-by: Lian Minghuan <Minghuan.Lian@freescale.com>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:34 -06:00
Wolfram Sang c68308dd50 gpio: move mpc8xxx/512x gpio driver to drivers/gpio
Move the driver to the place where it is expected to be nowadays. Also
rename its CONFIG-name to match the rest and adapt the defconfigs.
Finally, move selection of REQUIRE_GPIOLIB or WANTS_OPTIONAL_GPIOLIB to
the platforms, because this option is per-platform and not per-driver.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-09-23 00:14:15 +02:00
Ashish Kalra 3a93261f70 powerpc: introduce the ePAPR embedded hypervisor vmpic driver
The Freescale ePAPR reference hypervisor provides interrupt controller
services via a hypercall interface, instead of emulating the MPIC
controller.  This is called the VMPIC.

The ePAPR "virtual interrupt controller" provides interrupt controller
services for external interrupts.  External interrupts received by a
partition can come from two sources:

  - Hardware interrupts - hardware interrupts come from external
    interrupt lines or on-chip I/O devices.
  - Virtual interrupts - virtual interrupts are generated by the hypervisor
    as part of some hypervisor service or hypervisor-created virtual device.

Both types of interrupts are processed using the same programming model and
same set of hypercalls.

Signed-off-by: Ashish Kalra <ashish.kalra@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-06-27 08:30:26 -05:00
Rupjyoti Sarmah 3fb7933850 powerpc/4xx: Adding PCIe MSI support
This patch adds MSI support for 440SPe, 460Ex, 460Sx and 405Ex.

Signed-off-by: Rupjyoti Sarmah <rsarmah@apm.com>
Signed-off-by: Tirumala R Marri <tmarri@apm.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-05-26 15:00:37 +10:00
Benjamin Herrenschmidt ab814b938d powerpc: Add SCOM infrastructure
SCOM is a side-band configuration bus implemented on some processors.
This code provides a way for code to map and operate on devices via
SCOM, while the details of how that is implemented is left up to a
SCOM "controller" in the platform code.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-04-20 17:01:19 +10:00
Benjamin Herrenschmidt 0b05ac6e24 powerpc/xics: Rewrite XICS driver
This is a significant rework of the XICS driver, too significant to
conveniently break it up into a series of smaller patches to be honest.

The driver is moved to a more generic location to allow new platforms
to use it, and is broken up into separate ICP and ICS "backends". For
now we have the native and "hypervisor" ICP backends and one common
RTAS ICS backend.

The driver supports one ICP backend instanciation, and many ICS ones,
in order to accomodate future platforms with multiple possibly different
interrupt "sources" mechanisms.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-04-20 11:02:35 +10:00
Alexandre Bounine 388b78adc9 rapidio: modify configuration to support PCI-SRIO controller
1. Add an option to include RapidIO support if the PCI is available.
2. Add FSL_RIO configuration option to enable controller selection.
3. Add RapidIO support option into x86 and MIPS architectures.

Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-23 19:46:42 -07:00
Victor Gallardo d164f6d4f9 powerpc/4xx: Add suspend and idle support
Add suspend/resume support for 4xx compatible CPUs.
See /sys/power/state for available power states configured in.

Add two different idle states (idle-wait and idle-doze) controlled via sysfs.
Default is idle-wait.
	cat /sys/devices/system/cpu/cpu0/idle
	[wait] doze

To save additional power, use idle-doze.
	echo doze > /sys/devices/system/cpu/cpu0/idle
	cat /sys/devices/system/cpu/cpu0/idle
	wait [doze]

Signed-off-by: Victor Gallardo <vgallardo@apm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2010-11-29 10:05:06 -05:00
Harninder Rai 6db92cc9d0 powerpc/85xx: add cache-sram support
It adds cache-sram support in P1/P2 QorIQ platforms as under:

* A small abstraction over powerpc's remote heap allocator
* Exports mpc85xx_cache_sram_alloc()/free() APIs
* Supports only one contiguous SRAM window
* Drivers can do the following in Kconfig to use these APIs
    "select FSL_85XX_CACHE_SRAM if MPC85xx"
* Required SRAM size and the offset where SRAM should be mapped must be
  provided at kernel command line as :
    cache-sram-size=<value>
    cache-sram-offset=<offset>

Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-14 00:54:38 -05:00
matt mooney 4108d9ba90 powerpc/Makefiles: Change to new flag variables
Replace EXTRA_CFLAGS with ccflags-y and EXTRA_AFLAGS with asflags-y.

Signed-off-by: matt mooney <mfm@muteddisk.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2010-10-13 16:19:22 +11:00
Anton Vorontsov 4ffd6952a0 powerpc/85xx/86xx: Add suspend/resume support
This patch adds suspend/resume support for MPC8540 and MPC8641D-
compatible CPUs. To reach sleep state, we just write the SLP bit
into the PM control and status register.

So far we don't support Deep Sleep mode as found in newer MPC85xx
CPUs (i.e. MPC8536). It can be relatively easy implemented though,
and for it we reserve 'mem' suspend type.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-11-11 21:43:28 -06:00
Wolfgang Denk 87c441e54d powerpc/5xxx: Add common mpc5xxx_get_bus_frequency() function
So far, MPC512x used mpc512x_find_ips_freq() to get the bus frequency,
while MPC52xx used mpc52xx_find_ipb_freq().  Despite the different
clock names (IPS vs. IPB) the code was identical.

Use common code for both processor families.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-06-17 00:30:22 -06:00
Michael Ellerman ba55bd7436 powerpc: Add configurable -Werror for arch/powerpc
Add the option to build the code under arch/powerpc with -Werror.

The intention is to make it harder for people to inadvertantly introduce
warnings in the arch/powerpc code. It needs to be configurable so that
if a warning is introduced, people can easily work around it while it's
being fixed.

The option is a negative, ie. don't enable -Werror, so that it will be
turned on for allyes and allmodconfig builds.

The default is n, in the hope that developers will build with -Werror,
that will probably lead to some build breaks, I am prepared to be flamed.

It's not enabled for math-emu, which is a steaming pile of warnings.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-06-16 14:15:45 +10:00
Roderick Colenbrander 64f1650247 powerpc/virtex: Add support for Xilinx PCI host bridge
This patch adds support for the Xilinx plbv46-pci-1.03.a PCI host
bridge IPcore.

Signed-off-by: Roderick Colenbrander <thunderbird2k@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-06-06 10:14:22 -06:00
Anton Vorontsov 3d64de9c50 powerpc: Implement GPIO driver for simple memory-mapped banks
The driver supports very simple GPIO controllers, that is, when a
controller provides just a 'data' register. Such controllers may be
found in various BCSRs (Board's FPGAs used to control board's
switches, LEDs, chip-selects, Ethernet/USB PHY power, etc).

So far we support only 1-byte GPIO banks. Support for other widths may
be implemented when/if needed.

p.s.
To avoid "made up" compatible entries (like compatible = "simple-gpio"),
boards must call simple_gpiochip_init() to pass the compatible string.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-12-30 11:13:45 -06:00
Steven A. Falco 878e7556bf powerpc/4xx: Add PowerPC 4xx GPIO driver
This patch adds support for the GPIO functions of PPC40x and PPC44x
SOCs.

Signed-off-by: Steve Falco <sfalco@harris.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-10-17 13:33:44 -04:00
Josh Boyer 6070bf6afe powerpc: Remove old Makefile workaround for arch/ppc
There is an old workaround in the sysdev/Makefile for dealing
with arch/ppc vs. arch/powerpc compiles.  This is no longer
needed as arch/ppc is dead.

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2008-10-13 10:56:18 +11:00
Peter Korsgaard 1e16dfc1ba powerpc: gpio driver for mpc8349/8572/8610 and compatible
Structured similar to the existing QE GPIO support.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-09-23 10:41:16 -05:00
Michael Ellerman 7e302869e0 powerpc: Split-out common MSI bitmap logic into msi_bitmap.c
There are now two almost identical implementations of an MSI bitmap
allocator, one in mpic_msi.c and the other in fsl_msi.c.

Merge them together and put the result in msi_bitmap.c.  Some of the
MPIC bits will remain to provide a nicer interface for the MPIC users.

In the process we fix two buglets.  The first is that the allocation
routines, now msi_bitmap_alloc_hwirqs(), returned an unsigned result,
even though they use -1 to indicate allocation failure.  Although all
the callers were checking correctly, it is much better for the routine
to just return an int.  At least until someone wants > ~2 billion MSIs.

The second buglet is that the device tree reservation logic only
allowed power-of-two reservations.  AFAICT that didn't effect any
existing code but it's nicer if we can reserve arbitrary irqs from MSI
use.

We also add some selftests, which exposed the two buglets and now test
for them, as well as some basic sanity tests.  The tests are only built
when CONFIG_DEBUG_KERNEL=y.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-08-20 16:34:57 +10:00
Kumar Gala 9c4cb82515 powerpc: Remove use of CONFIG_PPC_MERGE
Now that arch/ppc is gone and CONFIG_PPC_MERGE is always set, remove
the dead code associated with !CONFIG_PPC_MERGE from arch/powerpc
and include/asm-powerpc.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-08-04 13:18:17 +10:00
Anton Vorontsov 5093bb965a powerpc/QE: switch to the cpm_muram implementation
This is very trivial patch. We're transitioning to the cpm_muram_*
calls. That's it.

Less trivial changes:
- BD_SC_* defines were defined in the cpm.h and qe.h, so to avoid redefines
  we remove BD_SC from the qe.h and use cpm.h along with cpm_muram_*
  prototypes;
- qe_muram_dump was unused and thus removed;
- added some code to the cpm_common.c to support legacy QE bindings
  (data-only node name).
- For convenience, define qe_* calls to cpm_*. So drivers need not to be
  changed.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-10 11:11:21 -05:00
Anton Vorontsov 83ff9dcf37 powerpc/sysdev: implement FSL GTM support
GTM stands for General-purpose Timers Module and able to generate
timer{1,2,3,4} interrupts. These timers are used by the drivers that
need time precise interrupts (like for USB transactions scheduling for
the Freescale USB Host controller as found in some QE and CPM chips),
or these timers could be used as wakeup events from the CPU deep-sleep
mode.

Things unimplemented:
1. Cascaded (32 bit) timers (1-2, 3-4).
   This is straightforward to implement when needed, two timers should
   be marked as "requested" and configured as appropriate.
2. Super-cascaded (64 bit) timers (1-2-3-4).
   This is also straightforward to implement when needed, all timers
   should be marked as "requested" and configured as appropriate.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-10 10:38:50 -05:00
Jason Jin 34e36c1541 [POWERPC] fsl: PCIe MSI support for 83xx/85xx/86xx processors.
This MSI driver can be used on 83xx/85xx/86xx board.
In this driver, virtual interrupt host and chip were
setup. There are 256 MSI interrupts in this host, Every 32
MSI interrupts cascaded to one IPIC/MPIC interrupt.
The chip was treated as edge sensitive and some necessary
functions were setup for this chip.

Before using the MSI interrupt, PCI/PCIE device need to
ask for a MSI interrupt in the 256 MSI interrupts. A 256bit
bitmap show which MSI interrupt was used, reserve bit in
the bitmap can be used to force the device use some designate
MSI interrupt in the 256 MSI interrupts. Sometimes this is useful
for testing the all the MSI interrupts. The msi-available-ranges
property in the dts file was used for this purpose.

Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-02 14:44:24 -05:00
Scott Wood 0b2cca804e [POWERPC] Add 6xx-style HID0_SLEEP support.
This adds a function to put a 6xx/7xx/7xxx/83xx family CPU into sleep
mode, and return after an interrupt has occurred.  It expects to be
called with interrupts disabled, and returns with interrupts disabled.
Interrupts are enabled while the processor is asleep, but the interrupt
that wakes the processor is not handled; it is still pending when this
function returns.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-05-16 23:22:28 +10:00
Anton Vorontsov acaa7aa30a [POWERPC] fsl_lbc: implement few UPM routines
Freescale UPM can be used to adjust localbus timings or to generate
orbitrary, pre-programmed "patterns" on the external Localbus signals.
This patch implements few routines so drivers could work with UPMs in
safe and generic manner.

So far there is just one user of these routines: Freescale UPM NAND
driver.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 01:01:38 -05:00
Stefan Roese 2a7069190e [POWERPC] 4xx: Add PPC4xx L2-cache support (440GX)
This patch adds support for the 256k L2 cache found on some IBM/AMCC
4xx PPC's. It introduces a common 4xx SoC file (sysdev/ppc4xx_soc.c)
which currently "only" adds the L2 cache init code. Other common 4xx
stuff can be added later here.

The L2 cache handling code is a copy of Eugene's code in arch/ppc
with small modifications.

Tested on AMCC Taishan 440GX.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-03-26 07:27:54 -05:00
Jochen Friedrich b5677d848c [POWERPC] CPM: Rename commproc to cpm1 and cpm2_common.c to cpm2.c
Rename commproc.[ch] to cpm1.[ch] to be more consistent with cpm2. Also
rename cpm2_common.c to cpm2.c as suggested by Scott Wood. Adjust the
includes accordingly.

Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-28 08:31:05 -06:00
David Gibson 22258fa40e [POWERPC] Enable RTC for Ebony and Walnut (v2)
This patch extends the Ebony and Walnut platform code to instantiate
the existing ds1742 RTC class driver for the DS1743 RTC/NVRAM chip
found on both those boards.  The patch uses a helper function to scan
the device tree and instantiate the appropriate platform_device based
on it, so it should be easy to extend for other boards which have mmio
mapped RTC chips.

Along with this, the device tree binding for the ds1743 chips is
tweaked, based on the existing DS1385 OF binding found at:
	http://playground.sun.com/1275/proposals/Closed/Remanded/Accepted/346-it.txt
Although that document covers the NVRAM portion of the chip, whereas
here we're interested in the RTC portion, so it's not entirely clear
if that's a good model.

This implements only RTC class driver support - that is /dev/rtc0, not
/dev/rtc, and the low-level get/set time callbacks remain
unimplemented.  That means in order to get at the clock you will
either need a modified version of hwclock which will look at
/dev/rtc0, or you'll need to configure udev to symlink rtc0 to rtc.

Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-01-25 07:07:26 -06:00
Kumar Gala de3c8d4182 [POWERPC] Move RapidIO support code from arch/ppc
Do just enough to move the RapidIO support code for 85xx over from arch/ppc
into arch/powerpc and make it still build.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23 19:35:15 -06:00
John Rigby b0bbad6068 [POWERPC] Add IPIC Kconfig option
IPIC is not just for 83xx anymore so make it a separate config option.

Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23 19:34:26 -06:00
Benjamin Herrenschmidt 5738ec6d00 [POWERPC] 4xx: PLB to PCI-X support
This adds base support code for the 4xx PCI-X bridge. It also provides
placeholders for the PCI and PCI-E version but they aren't supported
with this patch.

The bridges are configured based on device-tree properties.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2007-12-23 13:12:20 -06:00
Olof Johansson 38958dd911 [POWERPC] pasemi: Implement MSI support
Implement MSI support for PA Semi PWRficient platforms. MSI is done
through a special range of sources on the openpic controller, and they're
unfortunately breaking the usual concepts of how sources are programmed:

* The source is calculated as 512 + the value written into the MSI
  register
* The vector for this source is added to the source and reported
  through IACK

This means that for simplicity, it makes much more sense to just set the
vector to 0 for the source, since that's really the vector we expect to
see from IACK.

Also, the affinity/priority registers will affect 16 sources at a
time. To avoid most (simple) users from being limited by this, allocate
16 sources per device but use only one. This means that there's a total
of 32 sources.

If we get usage scenarions that need more sources, the allocator should
probably be revised to take an alignment argument and size, not just do
natural alignment.

Finally, since I'm already touching the MPIC names on pasemi, rename
the base one from the somewhat odd " PAS-OPIC  " to "PASEMI-OPIC".

Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-12-20 16:15:23 +11:00
Sylvain Munaut 2f9ea1bde0 [POWERPC] bestcomm: core bestcomm support for Freescale MPC5200
This patch adds support for the core of the BestComm API
for the Freescale MPC5200(b). The BestComm engine is a
microcode-controlled / tasks-based DMA used by several
of the onchip devices.

Setting up the tasks / memory allocation and all common
low level functions are handled by this patch.
The specifics details of each tasks and their microcode
are split-out in separate patches.

This is not the official API, but a much cleaner one.
(hopefully)

Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2007-10-16 17:09:34 -06:00
Grant Likely 4c3d514d7e [POWERPC] Don't build arch/powerpc/sysdev/dcr.c for ARCH=ppc kernels
dcr.c is an arch/powerpc only thing.  Compiling ppc405 arch/ppc kernels
throws warnings without this change.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2007-10-10 09:14:35 -06:00
Scott Wood c374e00e17 [POWERPC] Add early debug console for CPM serial ports.
This code assumes that the ports have been previously set up, with
buffers in DPRAM.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-10-03 20:35:43 -05:00
Grant Likely 4dc9783ea9 [POWERPC] Virtex: add xilinx interrupt controller driver
Adds support for the Xilinx opb-intc interrupt controller

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2007-10-03 07:23:14 -05:00
Tony Breeds aa3be5f32d [POWERPC] Implement {read,update}_persistent_clock
With these functions implemented we cooperate better with the generic
timekeeping code.  This obsoletes the need for the timer sysdev as a bonus.

Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-10-03 11:48:42 +10:00
Dale Farnsworth 9b41fcb0eb [POWERPC] Add Marvell mv64x60 udbg putc/getc functions
Commit 69331af, "Fixes and cleanups for earlyprintk aka boot console",
resulted in printk output prior to the initialization of the mpsc
console driver not being printed.  That commit causes the mpsc's
CON_PRINTBUFFER flag to be cleared since udbg should have printed
the previous output.

I guess we can no longer ignore udbg. :)

This patch provides udbg_putc() and udbg_getc() functions for the
Marvell mv64x60 chips. These functions are enabled if an mv64x60
port is to be used as the console as determined from the device tree.

Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-09-22 14:49:21 +10:00
Roy Zang 55c44991e2 [POWERPC] Create common fsl pci/e files based on 86xx platforms
Move
arch/powerpc/platforms/86xx/pci.c -> arch/powerpc/sysdev/fsl_pci.c
arch/powerpc/sysdev/fsl_pcie.h -> arch/powerpc/sysdev/fsl_pci.h
as the base to unify 83xx/85xx/86xx pci and pcie.

Add CONFIG_FSL_PCI to build fsl_pci.c for Freescale pci and pcie option.
The code still works for 86xx platforms.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-07-23 10:27:07 -05:00