Although the network interface is down, the RX packets number which
could be observed by ifconfig may keep on increasing.
This is because the WORK scheduled in netvsc_set_multicast_list()
may be executed after netvsc_close(). That means the rndis filter
may be re-enabled by do_set_multicast() even if it was closed by
netvsc_close().
By canceling possible WORK before close the rndis filter, the issue
could be never happened.
Signed-off-by: Wenqi Ma <wenqi_ma@trendmicro.com.cn>
Reviewed-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a potential deadlock scenario when the ks8851 driver
is removed. The interrupt handler schedules a workqueue which
acquires a mutex that ks8851_net_stop() also acquires before
flushing the workqueue. Previously lockdep wouldn't be able
to find this problem but now that it has the support we can
trigger this lockdep warning by rmmoding the driver after
an ifconfig up.
Fix the possible deadlock by disabling the interrupts in
the chip and then release the lock across the workqueue
flushing. The mutex is only there to proect the registers
anyway so this should be ok.
=======================================================
[ INFO: possible circular locking dependency detected ]
3.0.21-00021-g8b33780-dirty #2911
-------------------------------------------------------
rmmod/125 is trying to acquire lock:
((&ks->irq_work)){+.+...}, at: [<c019e0b8>] flush_work+0x0/0xac
but task is already holding lock:
(&ks->lock){+.+...}, at: [<bf00b850>] ks8851_net_stop+0x64/0x138 [ks8851]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&ks->lock){+.+...}:
[<c01b89c8>] __lock_acquire+0x940/0x9f8
[<c01b9058>] lock_acquire+0x10c/0x130
[<c083dbec>] mutex_lock_nested+0x68/0x3dc
[<bf00bd48>] ks8851_irq_work+0x24/0x46c [ks8851]
[<c019c580>] process_one_work+0x2d8/0x518
[<c019cb98>] worker_thread+0x220/0x3a0
[<c01a2ad4>] kthread+0x88/0x94
[<c0107008>] kernel_thread_exit+0x0/0x8
-> #0 ((&ks->irq_work)){+.+...}:
[<c01b7984>] validate_chain+0x914/0x1018
[<c01b89c8>] __lock_acquire+0x940/0x9f8
[<c01b9058>] lock_acquire+0x10c/0x130
[<c019e104>] flush_work+0x4c/0xac
[<bf00b858>] ks8851_net_stop+0x6c/0x138 [ks8851]
[<c06b209c>] __dev_close_many+0x98/0xcc
[<c06b2174>] dev_close_many+0x68/0xd0
[<c06b22ec>] rollback_registered_many+0xcc/0x2b8
[<c06b2554>] rollback_registered+0x28/0x34
[<c06b25b8>] unregister_netdevice_queue+0x58/0x7c
[<c06b25f4>] unregister_netdev+0x18/0x20
[<bf00c1f4>] ks8851_remove+0x64/0xb4 [ks8851]
[<c049ddf0>] spi_drv_remove+0x18/0x1c
[<c0468e98>] __device_release_driver+0x7c/0xbc
[<c0468f64>] driver_detach+0x8c/0xb4
[<c0467f00>] bus_remove_driver+0xb8/0xe8
[<c01c1d20>] sys_delete_module+0x1e8/0x27c
[<c0105ec0>] ret_fast_syscall+0x0/0x3c
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&ks->lock);
lock((&ks->irq_work));
lock(&ks->lock);
lock((&ks->irq_work));
*** DEADLOCK ***
4 locks held by rmmod/125:
#0: (&__lockdep_no_validate__){+.+.+.}, at: [<c0468f44>] driver_detach+0x6c/0xb4
#1: (&__lockdep_no_validate__){+.+.+.}, at: [<c0468f50>] driver_detach+0x78/0xb4
#2: (rtnl_mutex){+.+.+.}, at: [<c06b25e8>] unregister_netdev+0xc/0x20
#3: (&ks->lock){+.+...}, at: [<bf00b850>] ks8851_net_stop+0x64/0x138 [ks8851]
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reviewing the sysctl code in ax25 I spotted races in ax25_exit
where it is possible to receive notifications and packets after already
freeing up some of the data structures needed to process those
notifications and updates.
Call unregister_netdevice_notifier early so that the rest of the cleanup
code does not need to deal with network devices. This takes advantage
of my recent enhancement to unregister_netdevice_notifier to send
unregister notifications of all network devices that are current
registered.
Move the unregistration for packet types, socket types and protocol
types before we cleanup any of the ax25 data structures to remove the
possibilities of other races.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes and adds the irq handler for the
IC+ 101A/G where we need to read the reg17 to clean
the irq.
Also remove the flag for the 1001LF where no interrupt
can be used for this device.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MC77xx devices can operate in two modes: "Direct IP" or "QMI",
switchable using a password protected AT command. Both product ID
and USB interface configuration will change when switched.
The "sierra_net" driver supports the "Direct IP" mode. This driver
supports the "QMI" mode.
There are also multiple possible USB interface configurations in each
mode, some providing more than one wwan interface. Like many other
devices made for Windows, different interface types are identified
using a static interface number. We define a Sierra specific
interface whitelist to support this.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sp_pri_to_cos[] array size depends on the config but lets say it is
BX_E3B0_MAX_NUM_COS_PORT0 and max_num_of_cos is also
DCBX_E3B0_MAX_NUM_COS_PORT0. In the original code
"pri == max_num_of_cos" was accepted but it is one past the end of the
array.
Also we used "pri" before capping it. It's a harmless read past the end
of the array, but it would affect which error message gets printed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAX_ADDR_LEN is 32. ETH_ALEN is 6. mac->sa_data is a 14 byte array, so
the memcpy() is doing a read past the end of the array. I asked about
this on netdev and Ben Hutchings told me it's supposed to be copying
ETH_ALEN bytes (thanks Ben).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Beregalov reported skb_over_panic errors and provided stack
trace.
I occurs commit a21d45726a (tcp: avoid order-1 allocations on wifi and
tx path) added a regression, when a retransmit is done after a partial
ACK.
tcp_retransmit_skb() tries to aggregate several frames if the first one
has enough available room to hold the following ones payload. This is
controlled by /proc/sys/net/ipv4/tcp_retrans_collapse tunable (default :
enabled)
Problem is we must make sure _pskb_trim_head() doesnt fool
skb_availroom() when pulling some bytes from skb (this pull is done when
receiver ACK part of the frame).
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Marc MERLIN <marc@merlins.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From John:
Another batch of fixes intended for 3.4...
First up, we have a minor signedness fix for libertas from Amitkumar
Karwar. Next, Arend gives us a brcm80211 fix for correctly enabling
Tx FIFOs on channels 12 and 13. Bing Zhao gives us some register
address corrections for mwifiex. Felix give us a trio of fixes --
one for ath9k to wake the hardware properly from full sleep, one for
mac80211 to properly handle packets in cooked monitor mode, and one
for ensuring that the proper HT mode selection is honored.
Hauke gives us a bcma fix for handling the lack of an sprom. Jonathon
Bither gives us an ath5k fix for a missing THIS_MODULE build issue,
and another ath5k fix for an io mapping leak. Lukasz Kucharczyk
fixes a bitwise check in cfg80211, and Sujith gives us an ath9k fix
for assigning sequence numbers for fragmented frames. Finally, we
have a MAINTAINERS change from Wey-Yi Guy -- congrats to Johannes
Berg for taking the lead on iwlwifi. :-)
Signed-off-by: David S. Miller <davem@davemloft.net>
ops_init should free the net_generic data on
init failure and __register_pernet_operations should not
call ops_free when NET_NS is not enabled.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warning in net/sock.h:
Warning(include/net/sock.h:377): No description found for parameter 'sk_peek_off'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_grow_window() has to grow rcv_ssthresh up to window_clamp, allowing
sender to increase its window.
tcp_grow_window() still assumes a tcp frame is under MSS, but its no
longer true with LRO/GRO.
This patch fixes one of the performance issue we noticed with GRO on.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free card->mem in the error-handling code since it was successfully
allocated just above.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy load (flood ping) it is possible for the MDIO timeout to
expire before the loop checks the GO bit again. This patch adds an
additional check whether the operation was done before actually
returning -ETIMEDOUT.
To reproduce this bug, flood ping the device, e.g., ping -f -l 1000
After some time, a "timed out waiting for user access" warning
may appear. And even worse, link may go down since the PHY reported a
timeout.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: <stable@vger.kernel.org>
Cc: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functionally, this change is a NOP.
Semantically, rt6_clean_expires() wants to do rt->dst.from = NULL instead of
rt->dst.expires = 0. It is clearing the RTF_EXPIRES flag, so the union is going
to be treated as a pointer (dst.from) not a long (dst.expires).
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1716a961 (ipv6: fix problem with expired dst cache) broke PMTU
discovery. rt6_update_expires() calls dst_set_expires(), which only updates
dst->expires if it has not been set previously (expires == 0) or if the new
expires is earlier than the current dst->expires.
rt6_update_expires() needs to zero rt->dst.expires, otherwise it will contain
ivalid data left over from rt->dst.from and will confuse dst_set_expires().
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
arcrimi_probe() calls BUGMSG() before register_netdev() happens. BUGMSG()
itself prints dev->name, but as the format string hasn't been expanded by
register_netdev() yet, the output contains bogus device name such as
arc%d: Given: node 00h, shmem 0h, irq 0
As we don't know the device name yet, just drop the prefix completely from
the debugging messages.
Reported-by: Steven Young <sdyoung@vt220.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it so that we identify FCoE rings earlier than
ixgbe_set_rx_buffer_len. Instead we identify the Rx FCoE rings at
allocation time in ixgbe_alloc_q_vector.
The motivation behind this change is to avoid memory corruption when FCoE
is enabled. Without this change we were initializing the rings at 0, and
2K on systems with 4K pages, then when we bumped the buffer size to 4K with
order 1 pages we were accessing offsets 2K and 6K instead of 0 and 4K.
This was resulting in memory corruptions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Upon resume from standby, ixgbe may trigger the ASSERT_RTNL() in
netif_set_real_num_tx_queues(). The call stack is:
netif_set_real_num_tx_queues
ixgbe_set_num_queues
ixgbe_init_interrupt_scheme
ixgbe_resume
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Assigning sequence number for frames without taking care
of the fragment field breaks transmission of fragmented frames.
Fix this by assigning the fragment number properly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The broken check leads to rate control attempting to use HT40 while
the driver is configured for HT20. This leads to interesting hardware
issues.
HT40 can only be used if the channel type is either HT40- or HT40+
and if the channel type of the cell matches the local type.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add Johannes Berg as the primary maintainer for iwlwifi driver
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cooked monitor rx was recently changed to use ieee80211_add_rx_radiotap_header
instead of generating only limited radiotap information.
ieee80211_add_rx_radiotap_header assumes that FCS info is still present if
the hardware supports receiving it, however when cooked monitor rx packets
are processed, FCS info has already been stripped.
Fix this by adding an extra flag indicating FCS presence.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In register_netdevice(), when ndo_init() is successful and later
some error occurred, ndo_uninit() will be called.
So dummy deivce is desirable to implement ndo_uninit() method
to free percpu stats for this case.
And, ndo_uninit() is also called along with dev->destructor() when
device is unregistered, so in order to prevent dev->dstats from
being freed twice, dev->destructor is modified to free_netdev().
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make smsc75xx recalculate the hard_mtu after adjusting the
hard_header_len.
Without this, usbnet adjusts the MTU down to 1492 bytes, and the host is
unable to receive standard 1500-byte frames from the device.
Inspired by same fix on cdc_eem 78fb72f793.
Tested on ARM/Omap3 with EVB-LAN7500-LC.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A parameter set exists for WRED mode, called wred_set, to hold the same
values for qavg and qidlestart across all VQs. The WRED mode values had
been previously held in the VQ for the default DP. After these values
were moved to wred_set, the VQ for the default DP was no longer created
automatically (so that it could be omitted on purpose, to have packets
in the default DP enqueued directly to the device without using RED).
However, gred_dump() was overlooked during that change; in WRED mode it
still reads qavg/qidlestart from the VQ for the default DP, which might
not even exist. As a result, this command sequence will cause an oops:
tc qdisc add dev $DEV handle $HANDLE parent $PARENT gred setup \
DPs 3 default 2 grio
tc qdisc change dev $DEV handle $HANDLE gred DP 0 prio 8 $RED_OPTIONS
tc qdisc change dev $DEV handle $HANDLE gred DP 1 prio 8 $RED_OPTIONS
This fixes gred_dump() in WRED mode to use the values held in wred_set.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
If either call to pcan_usb_pro_send_req() in
drivers/net/can/usb/peak_usb/pcan_usb_pro.c::pcan_usb_pro_init()
fails, we'll leak the memory we allocated to 'usb_if' with kzalloc()
when the 'usb_if' variable goes out of scope without having been
assigned to anything as we 'return err;'.
Fix this by adding appropriate kfree(usb_if) calls to the error paths.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
bcma should check for a fallback sprom every time it can not find a
sprom on the card itself or a normal external sprom mapped into the
memory of the chip. When otp sprom support was introduced it tried to
read out the sprom from the wireless chip also if no otp sprom was
available. This caused a Data bus error in bcma_sprom_get() when
reading out the sprom for the SoC.
This fixes a regression introduced in commit:
commit 10d8493cd9
Author: Arend van Spriel <arend@broadcom.com>
Date: Tue Mar 6 15:50:48 2012 +0100
bcma: add support for on-chip OTP memory used for SPROM storage
This patch was tested on a Netgear WNDR3400 (Broadcom BCM4718 SoC).
Reported-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At the beginning of ks_rcv(), a for loop retrieves the
header information relevant to all the frames stored
in the mac's internal buffers. The number of pending
frames is stored as an 8 bits field in KS_RXFCTR.
If interrupts are disabled long enough to allow for more than
32 frames to accumulate in the MAC's internal buffers, a buffer
overflow occurs.
This patch fixes the problem by making the
driver's frame_head_info buffer big enough.
Well actually, since the chip appears to have 12K of
internal rx buffers and the shortest ethernet frame should
be 64 bytes long, maybe the limit could be set to
12*1024/64 = 192 frames, but 255 should be safer.
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are times we turn of the laser before shutdown. This is a bad thing
if we want to wake on lan to work so now we make sure the laser is on
before shutdown if we support WoL.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A workaround was previously put in the driver to reset the device when
transitioning to Sx in order to activate the changed settings of the PHY
OEM bits (Low Power Link Up, or LPLU, and GbE disable configuration) for
82577/8/9 devices. After further review, it was found such a reset can
cause the 82579 to confuse which version of 82579 it actually is and broke
LPLU on all 82577/8/9 devices. The workaround during an S0->Sx transition
on 82579 (instead of resetting the PHY) is to restart auto-negotiation
after the OEM bits are configured; the restart of auto-negotiation
activates the new OEM bits as does the reset. With 82577/8, the reset is
changed to a generic reset which fixes the LPLU bits getting set wrong.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The SMSC911x driver resets the ->head, ->data and ->tail pointers in the
skb on the reset path in order to avoid buffer overflow due to packet
padding performed by the hardware.
This patch fixes the receive path so that the skb pointers are fixed up
after the data has been read from the device, The error path is also
fixed to use number of words consistently and prevent erroneous FIFO
fastforwarding when skipping over bad data.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scratch register addresses have been changed for newer chips.
Since the old chip was never shipped and it will not be supported
any more, just update register addresses to support the new chips.
Cc: <stable@vger.kernel.org> # 3.2.y, 3.3.y
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware needs a reset to recover from full sleep. Issue this reset
directly in the ath9k_config call that turns off idle, otherwise tx
remains dead until the first channel change after the idle state change
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When cross compiling ath5k for a Mips machine with kernel 3.2.14
the compilation fails with "/ath5k/ahb.c:231:12: error: 'THIS_MODULE' undeclared here (not in a function)"
Fix the build by including <linux/export.h>
Signed-off-by: Jonathan Bither <jonbither@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There have been reports about not being able to use access-points
on channel 12 and 13 or having connectivity issues when these channels
were part of the selected regulatory domain. Upon switching to these
channels the brcmsmac driver suspends the transmit dma fifos. This
patch resumes them upon handing over the first received beacon to
mac80211.
This patch is to be applied to the stable tree for kernel versions
3.2 and 3.3.
Cc: stable@vger.kernel.org
Tested-by: Francesco Saverio Schiavarelli <fschiava@libero.it>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Return type for lbs_auth_to_authtype() is changed from "u8" to
"int" to return negative error code correctly.
Also an error check is added in connect handler for invalid auth
type.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the ks8851_rdreg16 call above the call to request_irq and cache
the result for subsequent repeated use. A spurious interrupt may
otherwise cause a crash. Thanks to Stephen Boyd, Flavio Leitner, and
Ben Hutchings for feedback.
Signed-off-by: Matt Renzelmann <mjr@cs.wisc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also fix MAINTAINERS file to reflect autorship.
Daniel and Ariane changed coding style but not any functional changes in the driver
itself.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
We set intr mask before its handler is registered, this does not work well when
8139cp is sharing irq line with other devices. As the irq could be enabled by
the device before 8139cp's hander is registered which may lead unhandled
irq. Fix this by introducing an helper cp_irq_enable() and call it after
request_irq().
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem:
There was two separate work_struct structures which share one
handler. Unfortunately getting atl1_adapter structure from
work_struct in case of DMA error was done from incorrect
offset which cause kernel panics.
Solution:
The useless work_struct for DMA error removed and
handler name changed to more generic one.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb struct ubuf_info callback gets passed struct ubuf_info
itself, not the arg value as the field name and the function signature
seem to imply. Rename the arg field to ctx to match usage,
add documentation and change the callback argument type
to make usage clear and to have compiler check correctness.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e675f0cc9a ("ppp: Don't stop and
restart queue on every TX packet") introduced a race condition which
could leave the net queue stopped even when the channel is no longer
busy. By calling netif_stop_queue() from ppp_start_xmit(), based on the
return value from ppp_xmit_process() but *after* all the locks have been
dropped, we could potentially do so *after* the channel has actually
finished transmitting and attempted to re-wake the queue.
Fix this by moving the netif_stop_queue() into ppp_xmit_process() under
the xmit lock. I hadn't done this previously, because it gets called
from other places than ppp_start_xmit(). But I now think it's the better
option. The net queue *should* be stopped if the channel becomes
congested due to writes from pppd, anyway.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ipv6 dst cache which copy from the dst generated by ICMPV6 RA packet.
this dst cache will not check expire because it has no RTF_EXPIRES flag.
So this dst cache will always be used until the dst gc run.
Change the struct dst_entry,add a union contains new pointer from and expires.
When rt6_info.rt6i_flags has no RTF_EXPIRES flag,the dst.expires has no use.
we can use this field to point to where the dst cache copy from.
The dst.from is only used in IPV6.
rt6_check_expired check if rt6_info.dst.from is expired.
ip6_rt_copy only set dst.from when the ort has flag RTF_ADDRCONF
and RTF_DEFAULT.then hold the ort.
ip6_dst_destroy release the ort.
Add some functions to operate the RTF_EXPIRES flag and expires(from) together.
and change the code to use these new adding functions.
Changes from v5:
modify ip6_route_add and ndisc_router_discovery to use new adding functions.
Only set dst.from when the ort has flag RTF_ADDRCONF
and RTF_DEFAULT.then hold the ort.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_dbg instead of dev_err for reporting in cfhsi_wakeup_cb.
Signed-off-by: Kim Lilliestierna <kim.xx.lilliestierna@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wenqi Ma
Stephen Boyd
Eric W. Biederman
Giuseppe CAVALLARO
Bjørn Mork
Dan Carpenter
Eric Dumazet
David S. Miller
John W. Linville
Julian Anastasov
Randy Dunlap
Julia Lawall
Christian Riesch
Jiri Bohac
Jiri Kosina
Alexander Duyck
Benjamin Poirier
Sujith Manoharan
Felix Fietkau
Wey-Yi Guy
Hiroaki SHIMODA
Stephane Fillod
David Ward
Jesper Juhl
Hauke Mehrtens
Davide Ciminaghi
Don Skidmore
Bruce Allan
Will Deacon
Bing Zhao
Jonathan Bither
Lukasz Kucharczyk
Arend van Spriel
Amitkumar Karwar
Matt Renzelmann
Michal Simek
Jason Wang
Tony Zelenoff
Michael S. Tsirkin
David Woodhouse
Gao feng
Kim Lilliestierna XX