HW recommends to set DUM bit on device power up, so that DPIB write
request occurs every frame regardless of whether DPIB has changed or
not. This addresses incorrect position reporting for capture streams.
Signed-off-by: Leoni Prodduvaka <leoni.prodduvaka@intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
McBSP used to work correctly as long as compat DMA probing, removed by
commit 642aafea88 ("ASoC: ti: remove compat dma probing"), was
available. New method of DMA probing apparently requires users to
provide channel names when registering with SDMA, while McBSP passes
NULLs. Fix it.
The same probably applies to McASP (not tested), hence the patch fixes
both.
Fixes: 642aafea88 ("ASoC: ti: remove compat dma probing")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In display codecs supported by hdac_hdmi, the connection indices are
shared by all converters. At boot and resume from suspend,
the connection state may be reset to default values.
In case of multiple connected pins (multiple monitors connected
with audio capability), routing and mute status of pins that
are not connected to any PCM, may interfere with other pins.
E.g. after resume from S3 with multiple monitors, unless
all converters are in active use, playback to some PCMs may
be muted due to the default settings of unrelated converters.
Avoid this by ensuring all pin:cvt selections are correct
in codec whenever a converter is enabled for playback.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The content of SND_SOC_DAIFMT_FORMAT_MASK is a number, not a bitfield,
so the test to check if the format is i2s is wrong. Because of this the
clock setting may be wrong. For example, the sample clock gets inverted
in DSP B mode, when it should not.
Fix the lrclk invert helper function
Fixes: 1a11d88f49 ("ASoC: meson: add tdm formatter base driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Right justified format is actually not supported by the amlogic tdm output
encoder.
Fixes: c41c2a355b ("ASoC: meson: add tdm output driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Right justified format is actually not supported by the amlogic tdm input
decoder.
Fixes: 13a22e6a98 ("ASoC: meson: add tdm input driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no pull-up resistor at IRQ line where it connects from
the codec to SoC. When booting, the signal of IRQ pin will keep low
which makes the SoC invoke the ISR repeatedly because the IRQ is
registered trigger low. It will not stop until the codec sets up
the interruption and pulls the signal high. In the patch,
nau8825 will internally pull the signal to high at booting in case
the fake interrupts happen.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Tested-by: Cheng-Yi Chiang <cychiang@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the client_mutex lock to snd_soc_unbind_card() before
removing link components. This prevents the deadlock
in the error path in snd_soc_instantiate_card().
Fixes: 34ac3c3eb8 (ASoC: core: lock client_mutex while removing
link components)
Reported-by: kernelci.org bot <bot@kernelci.org>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we call snd_soc_component_set_jack(component, NULL, NULL) we should
set rt274->jack to passed jack, so when interrupt is triggered it calls
snd_soc_jack_report(rt274->jack, ...) with proper value.
This fixes problem in machine where in register, we call
snd_soc_register(component, &headset, NULL), which just calls
rt274_mic_detect via callback.
Now when machine driver is removed "headset" will be gone, so we
need to tell codec driver that it's gone with:
snd_soc_register(component, NULL, NULL), but we also need to be able
to handle NULL jack argument here gracefully.
If we don't set it to NULL, next time the rt274_irq runs it will call
snd_soc_jack_report with first argument being invalid pointer and there
will be Oops.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During the integration of HDaudio support, we changed the way in which
we get hdev in snd_hdac_ext_bus_device_init() to use one preallocated
with devm_kzalloc(), however it still left kfree(hdev) in
snd_hdac_ext_bus_device_exit(). It leads to oopses when trying to
rmmod and modprobe. Fix it, by just removing kfree call.
SOF also uses some of the snd_hdac_ functions for HDAudio support but
allocated the memory with kzalloc. A matching fix is provided
separately to align all users of the snd_hdac_ library.
Fixes: 6298542fa3 ("ALSA: hdac: remove memory allocation from snd_hdac_ext_bus_device_init")
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are already defined ppcap and ppcap interrupt functions, use
the already defined functions for easy code read.
Fixes: 8a300c8fb1 ("ASoC: SOF: Intel: Add HDA controller for Intel DSP")
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Zhu Yingjiang <yingjiang.zhu@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kernel crashes when an ASoC component rebinding.
The dai_link->platforms has been reset to NULL by soc_cleanup_platform()
in soc_cleanup_card_resources() when un-registering component. However,
it has no chance to re-allocate the dai_link->platforms when registering
the component again.
Move the DAI pre-links initiation from snd_soc_register_card() to
snd_soc_instantiate_card() to make sure all DAI pre-links get initiated
when component rebinding.
As an example, by using the following commands:
- echo -n max98357a > /sys/bus/platform/drivers/max98357a/unbind
- echo -n max98357a > /sys/bus/platform/drivers/max98357a/bind
Got the error message:
"Unable to handle kernel NULL pointer dereference at virtual address".
The call trace:
snd_soc_is_matching_component+0x30/0x6c
soc_bind_dai_link+0x16c/0x240
snd_soc_bind_card+0x1e4/0xb10
snd_soc_add_component+0x270/0x300
snd_soc_register_component+0x54/0x6c
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform override code uses devm_ functions to allocate memory for
the new name but the card device is not initialized. Fix by moving the
init earlier.
Fixes: f403906da0 ("ASoC: Intel: cht_bsw_rt5672: platform name fixup support")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform override code uses devm_ functions to allocate memory for
the new name but the card device is not initialized. Fix by moving the
init earlier.
Fixes: 4506db8043 ("ASoC: Intel: cht_bsw_nau8824: platform name fixup support")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform override code uses devm_ functions to allocate memory for
the new name but the card device is not initialized. Fix by moving the
init earlier.
Fixes: e4bc6b1195 ("ASoC: Intel: bytcht_es8316: platform name fixup support")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform override code uses devm_ functions to allocate memory for
the new name but the card device is not initialized. Fix by moving the
init earlier.
Fixes: 7e7e24d7c7 ("ASoC: Intel: cht_bsw_max98090_ti: platform name fixup support")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whilst testing the capture functionality of the i2s on the newer
SoCs it was noticed that the recording was somewhat distorted.
This was due to the offset not being set correctly on the receiver
side.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Although not causing any noticeable issues, the mask for the
channel offset is covering too many bits.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The supported formats are S16_LE and S24_LE now. However, by datasheet
of max98090, S24_LE is only supported when it is in the right justified
mode. We should remove 24-bit format if it is not in that mode to avoid
triggering error.
Signed-off-by: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix gcc build error while CONFIG_I2C is not set
sound/soc/codecs/da7219.c:2640:1: warning: data definition has no type or storage class
module_i2c_driver(da7219_i2c_driver);
^~~~~~~~~~~~~~~~~
sound/soc/codecs/da7219.c:2640:1: error: type defaults to int in declaration of module_i2c_driver [-Werror=implicit-int]
sound/soc/codecs/da7219.c:2640:1: warning: parameter names (without types) in function declaration
sound/soc/codecs/da7219.c:2629:26: warning: da7219_i2c_driver defined but not used [-Wunused-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 6d817c0e9f ("ASoC: codecs: Add da7219 codec driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
while building without PCI:
sound/soc/sof/intel/hda.o: In function `hda_dsp_probe':
hda.c:(.text+0x79c): undefined reference to `pci_ioremap_bar'
hda.c:(.text+0x79c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `pci_ioremap_bar'
hda.c:(.text+0x7c4): undefined reference to `pci_ioremap_bar'
hda.c:(.text+0x7c4): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `pci_ioremap_bar'
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e13ef82a9a ("ASoC: SOF: add COMPILE_TEST for PCI options")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The definitions for DSP oops structures were not aligned
correctly to current FW ABI version 3.6.0, leading to
invalid data being printed out to debug logs. Fix the structs
and update related platform code accordingly.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HDA_DEV_ASOC type codec device refcounts are managed differently
from HDA_DEV_LEGACY devices. The refcount is released explicitly
in snd_hdac_ext_bus_device_remove() for ASOC type devices.
So, remove the put_device() call in snd_hda_codec_dev_free()
for such devices to make the refcount balanced. This will prevent
the NULL pointer exception when the codec driver is released
after the card is freed.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously the structure used bitfields, which do not guarantee bit
ordering.
This change makes sure the order is clearly defined. It also renames
and repurposes the field for general use.
Signed-off-by: Slawomir Blauciak <slawomir.blauciak@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We had a couple of misses with ABI changes, e.g. for Xtensa oops
information and the integration of sound trigger, before we set-up a
formal process to track evolutions.
With this patch, the SOF kernel patches are officially aligned with
the firmware 3.6 level. Changing this level has no impact on existing
users and is fully backwards-compatible.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add soundwire dai type and update ABI version.
Signed-off-by: Pan Xiuli <xiuli.pan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We missed these two definitions for GDB support and component
notifications, they are defined for the SOF firmware. Since they are
not used by the kernel so far, we can still add them without any ABI
change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This tablet has an incorrect acpi identifier just like
Thinkpad10 tablet, which is why it is trying to load the RT5640 driver
instead of the RT5762 driver. The RT5640 driver, on the other hand, checks
the hardware ID, so no driver are loaded during boot. This fix resolves to
load the RT5672 driver on this tablet during boot. It also provides the
correct IO configuration, like the jack detect mode 3, for 1.8V pullup. I
would like to thank Pierre-Louis Bossart for helping with this patch.
Signed-off-by: Kovács Tamás <kepszlok@zohomail.eu>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allwinner DAC seems to have a delay in the Speaker audio routing. When
playing a sound for the first time, the sound gets chopped. On a second
play the sound is played correctly. After some time (~5s) the issue gets
back.
This commit seems to be fixing the same issue as bf14da7 but
for another codepath.
This is the DTS that was used to debug the problem.
&codec {
allwinner,pa-gpios = <&r_pio 0 11 GPIO_ACTIVE_HIGH>; /* PL11 */
allwinner,audio-routing =
"Speaker", "LINEOUT";
status = "okay";
}
Signed-off-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
re-write hda_init_caps and remove the HDA reset, clean HDA
streams and clear interrupt steps in hda_dsp_probe so the
HDA init steps will not be called twice if the
CONFIG_SND_SOC_SOF_HDA is true.
Fixes: 8a300c8fb1 ("ASoC: SOF: Intel: Add HDA controller for Intel DSP")
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Zhu Yingjiang <yingjiang.zhu@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently on all supported platforms the IPC IRQ thread first signals
the sender when an IPC response is received from the DSP, then unmasks
the IPC interrupt. Those actions are performed without holding any
locks, so the thread can be interrupted between them. IPC timeouts
have been observed in such scenarios: if the sender is woken up and it
proceeds with sending the next message without unmasking the IPC
interrupt, it can miss the next response. This patch takes a spin-lock
to prevent the IRQ thread from being preempted at that point. It also
makes sure, that the next IPC transmission by the host cannot take
place before the IRQ thread has finished updating all the required IPC
registers.
Fixes: 53e0c72d98 ("ASoC: SOF: Add support for IPC IO between DSP and Host")
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The size for the bytes kcontrol should include the abi header, that is,
data->size + sizeof(*data), it is also aligned with get method after
this change.
Fixes: c3078f5397 ("ASoC: SOF: Add Sound Open Firmware KControl support")
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the SOF hw_params() fail, typically with an IPC error thrown by the
firmware, the period_elapsed workqueue is not initialized, but we
still cancel it in hw_free(), which results in a kernel warning.
Move the initialization to the .open callback. Tested on Broadwell
(Samus) and IceLake.
Fixes: e2803e610a ("ASoC: SOF: PCM: add period_elapsed work to fix
race condition in interrupt context")
GitHub issue: https://github.com/thesofproject/linux/issues/932
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sof_pcm_hw_params() can only be called once to setup the FW hw_params.
So after calling sof_pcm_hw_params(), hw_params_upon_resume flag must
be cleared to avoid multiple invoking sof_pcm_hw_params() by prepare.
For example, after resume, there is an xrun happened, prepare() will
be called. As the hw_params_upon_resume flag is not cleared,
sof_pcm_hw_params() will be called and this will cause IPC timeout.
This patch fixes such issues.
Fixes: 868bd00f49 ("ASoC: SOF: Add PCM operations support")
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In some configurations, it's a requirement to split the probe in two,
with a second part handled in a workqueue (e.g. for HDMI support
which depends on the DRM modules).
SOF already handles these configurations but the error flow is
incorrect. When an error occurs in the workqueue, the probe has
technically already completed. If we release the resources on errors,
this generates kernel oops/use-after-free when the resources are
released a second time on module removal.
GitHub issue: https://github.com/thesofproject/linux/issues/945
Fixes: c16211d622 ("ASoC: SOF: Add Sound Open Firmware driver core")
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No need to call snd_soc_unregister_component in case of error
because the component device is resource-managed.
Fixes: c16211d622 ("ASoC: SOF: Add Sound Open Firmware driver core")
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_sof_remove() disables the DSP and unmaps the DSP BAR.
Removing topology after disabling the DSP results in a
kernel panic while unloading the pipeline widget. This is
because pipeline widget unload attempts to power down
the core it is scheduled on by accessing the DSP registers.
So, the suggested fix here is to unregister the machine driver
first to remove the topology and then disable the DSP
to avoid the situation described above.
Note that the kernel panic only happens in cases where the
HDaudio link is not managed by the hdac library,
e.g. no codec or when HDMI is not supported.
When the hdac library is used, snd_sof_remove() calls
snd_hdac_ext_bus_device_remove() to remove the codec which
unregisters the component driver thereby also removing the
topology before the DSP is disabled.
Fixes: c16211d622 ("ASoC: SOF: Add Sound Open Firmware driver core")
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 53e947a0e1 ("ASoC: soc-core: merge card resources cleanup
method") merged cleanup method of snd_soc_instantiate_card() and
soc_cleanup_card_resources().
But, after this commit, if user uses unbind/bind to Component factor
drivers, Kernel might indicates refcount error at
soc_cleanup_card_resources().
The 1st reason is card->snd_card is still exist even though
snd_card_free() was called, but it is already cleaned.
We need to set NULL to it.
2nd is card->dapm and card create debugfs, but its dentry is still
exist even though it was removed. We need to set NULL to it.
Fixes: 53e947a0e1 ("ASoC: soc-core: merge card resources cleanup method")
Cc: stable@vger.kernel.org # for v5.1
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Removing link components results in topology unloading. So,
acquire the client_mutex before removing components in
soc_remove_link_components. This will prevent the lockdep warning
seen when dai links are removed during topology removal.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Revert commit 069d037aea ("ASoC: simple-card: Fix configuration of
DAI format"). During further review, it turns out that the actual issue
was caused by an incorrectly formatted device-tree node describing the
soundcard.
The following is incorrect because the simple-audio-card
'bitclock-master' and 'frame-master' properties should not reference the
actual codec phandle ...
sound {
compatible = "simple-audio-card";
...
=> simple-audio-card,bitclock-master = <&codec>;
=> simple-audio-card,frame-master = <&codec>;
...
simple-audio-card,cpu {
sound-dai = <&xxx>;
};
simple-audio-card,codec {
=> sound-dai = <&codec>;
};
};
Rather, these properties should reference the phandle to the
'simple-audio-card,codec' property as shown below ...
sound {
compatible = "simple-audio-card";
...
=> simple-audio-card,bitclock-master = <&codec>;
=> simple-audio-card,frame-master = <&codec>;
...
simple-audio-card,cpu {
sound-dai = <&xxx>;
};
=> codec: simple-audio-card,codec { /* simple-card wants here */
sound-dai = <&xxx>; /* not here */
};
};
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The use of BIT/GENMASK was incorrect, fix.
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The RT5682 codec button mapping, initially copied from the DA7219 one,
needs to be corrected.
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When configuring a codec to be both bit-clock and frame-master, it was
found that the codec was always configured as bit-clock and frame-slave.
Looking at the simple_dai_link_of() function there appears to be two
problems with the configuration of the DAI format, which are ...
1. The function asoc_simple_parse_daifmt() is called before the function
asoc_simple_parse_codec() and this means that the device-tree node
for the codec has not been parsed yet, which is needed by the
function asoc_simple_parse_daifmt() to determine who is the codec.
2. The phandle passed to asoc_simple_parse_daifmt() is the phandle to
the 'codec' node and not the phandle of the actual codec defined by
the 'sound-dai' property under the 'codec' node.
Fix the above by moving the call to asoc_simple_parse_daifmt() after the
the call to asoc_simple_parse_codec() and pass the phandle for the codec
to asoc_simple_parse_daifmt().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The selection order of m/c in match table is corrected
to use common codec as last in the list.
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a case when a we want to read a large number of bytes that
require a burst but is not a multiple of the word size (8). When this
happens rt5677_spi_reverse will run off the end of the buffer. The
solution is to tell spi_reverse the actual size of the destination and
stop if we reach it even if we have data left that we read.
Cc: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_link_event() is updating snd_soc_dai :: active,
but it is unbalance.
It counts up if it has startup callback.
case SND_SOC_DAPM_PRE_PMU:
...
snd_soc_dapm_widget_for_each_source_path(w, path) {
...
if (source->driver->ops->startup) {
...
=> source->active++;
}
...
}
...
But, always counts down
case SND_SOC_DAPM_PRE_PMD:
...
snd_soc_dapm_widget_for_each_source_path(w, path) {
...
=> source->active--;
...
}
This patch always counts up when SND_SOC_DAPM_PRE_PMD.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regcache_mark_dirty before regcache_sync for power
of codec may be lost at suspend, then all the register
need to be reconfigured.
Fixes: 0c516b4ff8 ("ASoC: cs42xx8: Add codec driver
support for CS42448/CS42888")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the output sample rate is [8kHz, 30kHz], the limitation
of the supported ratio range is [1/24, 8]. In the driver
we use (8kHz, 30kHz) instead of [8kHz, 30kHz].
So this patch is to fix this issue and the potential rounding
issue with divider.
Fixes: fff6e03c7b ("ASoC: fsl_asrc: add support for 8-30kHz
output sample rate")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_component_update_bits() may return 1 if operation
was successful and the value of the register changed.
Return a non-zero in ak4458_rstn_control for an error only.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cezary Rojewski
Janusz Krzysztofik
Kai Vehmanen
Jerome Brunet
John Hsu
Alex Levin
Ranjani Sridharan
Amadeusz Sławiński
Zhu Yingjiang
Tzung-Bi Shih
Pierre-Louis Bossart
Marcus Cooper
Yu-Hsuan Hsu
YueHaibing
Slawomir Blauciak
Pan Xiuli
Kovács Tamás
Georgii Staroselskii
Guennadi Liakhovetski
Keyon Jie
Libin Yang
Kuninori Morimoto
Jon Hunter
Sathya Prakash M R
Curtis Malainey
S.j. Wang
Viorel Suman