Fixes several chipselect bugs in the pxa2xx_spi driver. These bugs are in
all versions of this driver and prevent using it with chips like m25p16
flash.
1. The spi_transfer.cs_change flag is handled too early:
before spi_transfer.delay_usecs applies, thus making the
delay ineffective at holding chip select.
2. spi_transfer.delay_usecs is ignored on the last transfer
of a message (likewise not holding chipselect long enough).
3. If spi_transfer.cs_change is set on the last transfer, the
chip select is always disabled, instead of the intended
meaning: optionally holding chip select enabled for the
next message.
Those first three bugs were fixed with a relocation of delays
and chip select de-assertions.
4. If a message has the cs_change flag set on the last transfer,
and had the chip select stayed enabled as requested (see 3,
above), it would not have been disabled if the next message is
for a different chip. Fixed by dropping chip select regardless
of cs_change at end of a message, if there is no next message
or if the next message is for a different chip.
This patch should apply to all kernels back to and including 2.6.20;
it was test patched against 2.6.20. An additional patch would be
required for older kernels, but those versions are very buggy anyway.
Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Cc: Vernon Sauder <vernoninhand@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Error out on transfer length != multiple of bytes per word with -EINVAL.
Fixes a buffer overrun crash if length < bytes per word.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit a61f5345 (spi_mpc83xx clockrate fixes) broke clockrate calculation
for low speeds. SPMODE_DIV16 should be set if the divider is higher than
64, not only if the divider gets clipped to 1024.
Furthermore, the clipping check was off by a factor 16 as well.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A "Quicklists: 0 kB" line has just started appearing in
/proc/meminfo, but most architectures (including x86) don't have
them configured, so #ifdef it, like the highmem lines.
And those architectures which do have quicklists configured are
using them for page tables: so let's place it next to PageTables.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no description of bit 4 of coredump_filter in the
documentation. This patch adds it.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If all the cpus in a cpuset are offlined, the tasks in it will be moved to
the nearest ancestor with non-empty cpus.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Jackson <pj@sgi.com>
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After the patch:
commit 0b2f630a28
Author: Miao Xie <miaox@cn.fujitsu.com>
Date: Fri Jul 25 01:47:21 2008 -0700
cpusets: restructure the function update_cpumask() and update_nodemask()
It might happen that 'echo 0 > /cpuset/sub/cpus' returned failure but 'cpus'
has been changed, because cpus was changed before calling heap_init() which
may return -ENOMEM.
This patch restores the orginal behavior.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Cc: Paul Jackson <pj@sgi.com>
Cc: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
akpm: these have no callers at this time, but they shall soon, so let's
get them right.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Print parent directory name as well.
The aim is to catch non-creation of parent directory when proc_mkdir will
return NULL and all subsequent registrations go directly in /proc instead
of intended directory.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Fixed insane printk string while at it. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the MN10300 fault handler to make it check in_atomic() rather than
in_interrupt() as commit 6edaf68a87 did for other
architectures:
Author: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Wed Dec 6 20:32:18 2006 -0800
[PATCH] mm: arch do_page_fault() vs in_atomic()
In light of the recent pagefault and filemap_copy_from_user work I've
gone through all the arch pagefault handlers to make sure the
inc_preempt_count() 'feature' works as expected.
Several sections of code (including the new filemap_copy_from_user)
rely on the fact that faults do not take locks under increased preempt
count.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The callers of sg_copy_buffer must disable interrupts before calling
it (since it uses kmap_atomic). Some callers use it on
interrupt-disabled code but some need to take the trouble to disable
interrupts just for this. No wonder they forget about it and we hit a
bug like:
http://bugzilla.kernel.org/show_bug.cgi?id=11529
James said that it might be better to disable interrupts inside the
function rather than risk the callers getting it wrong.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* 'kvm-updates/2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: VMX: Always return old for clear_flush_young() when using EPT
KVM: SVM: fix guest global tlb flushes with NPT
KVM: SVM: fix random segfaults with NPT enabled
We still have life time issues with the sysfs command filter kobject,
so disable it for 2.6.27 release. We can revisit this and make it work
properly for 2.6.28, for 2.6.27 release it's too risky.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
As well as discard fake accessed bit and dirty bit of EPT.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Accesses to CR4 are intercepted even with Nested Paging enabled. But the code
does not check if the guest wants to do a global TLB flush. So this flush gets
lost. This patch adds the check and the flush to svm_set_cr4.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch introduces a guest TLB flush on every NPF exit in KVM. This fixes
random segfaults and #UD exceptions in the guest seen under some workloads
(e.g. long running compile workloads or tbench). A kernbench run with and
without that fix showed that it has a slowdown lower than 0.5%
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@qumranet.com>
commit 0d3244d643 ("V4L/DVB (8342):
sh_mobile_ceu_camera: Add SuperH Mobile CEU driver V3") introduced
VIDEO_SH_MOBILE_CEU, which selects VIDEOBUF_DMA_CONTIG. This circumvents the
dependency on HAS_DMA of VIDEOBUF_DMA_CONTIG.
Add a dependency on HAS_DMA to VIDEO_SH_MOBILE_CEU to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
git commit 74811f355f causes crash at
module load (or boot) time on my machine with a hpt374 controller.
The reason for this is that for initializing second controller which sets
(hwif->dev == host->dev[1]) to true (1), adds 1 to a void ptr, which
advances it by one byte instead of advancing it by sizeof(hpt_info) bytes.
Because of this, all initialization functions get corrupted data in info
variable which causes a crash at boot time.
This patch fixes that and makes my machine boot again.
The card itself is a HPT374 raid conroller: Here is the lspci -v output:
03:06.0 RAID bus controller: HighPoint Technologies, Inc. HPT374 (rev
07)
Subsystem: HighPoint Technologies, Inc. Unknown device 0001
Flags: bus master, 66MHz, medium devsel, latency 120, IRQ 28
I/O ports at 8000 [size=8]
I/O ports at 7800 [size=4]
I/O ports at 7400 [size=8]
I/O ports at 7000 [size=4]
I/O ports at 6800 [size=256]
Expansion ROM at fe8e0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
03:06.1 RAID bus controller: HighPoint Technologies, Inc. HPT374 (rev
07)
Subsystem: HighPoint Technologies, Inc. Unknown device 0001
Flags: bus master, 66MHz, medium devsel, latency 120, IRQ 28
I/O ports at 9800 [size=8]
I/O ports at 9400 [size=4]
I/O ports at 9000 [size=8]
I/O ports at 8800 [size=4]
I/O ports at 8400 [size=256]
Capabilities: [60] Power Management version 2
Signed-off-by: Masoud Sharbiani <masouds@google.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
[bart: use dev_get_drvdata() per Sergei's suggestion]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make ia64 refrain from clearing a given to-be-offlined CPU's bit in the
cpu_online_mask until it has processed pending irqs. This change
prevents other CPUs from being blindsided by an apparently offline CPU
nevertheless changing globally visible state. Also remove the existing
redundant cpu_clear(cpu, cpu_online_map).
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Error handling code following a kmalloc should free the allocated data.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Tony Luck <tony.luck@intel.com>
bte.h expects a #define of L1_CACHE_MASK which is currently only
in bte.c. This small patch gets bte.h to include cleanly and makes
BTE_UNALIGNED_COPY not report errors.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Broke the non modular builds by moving an essential function into
modules.c. Fix this by moving it out again and into asm/sections.h as
an inline. To do this, the definitions of struct fdesc and struct
got_val have been lifted out of modules.c and put in asm/elf.h where
they belong.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
ocfs2 will become read-only if we try to read the bytes which pass
the end of i_size. This can be easily reproduced by following steps:
1. mkfs a ocfs2 volume with bs=4k cs=4k and nosparse.
2. create a small file(say less than 100 bytes) and we will create the file
which is allocated 1 cluster.
3. read 8196 bytes from the kernel using O_DIRECT which exceeds the limit.
4. The ocfs2 volume becomes read-only and dmesg shows:
OCFS2: ERROR (device sda13): ocfs2_direct_IO_get_blocks:
Inode 66010 has a hole at block 1
File system is now read-only due to the potential of on-disk corruption.
Please run fsck.ocfs2 once the file system is unmounted.
So suppress the ERROR message.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
ipv6: Fix OOPS in ip6_dst_lookup_tail().
ipsec: Restore larval states and socket policies in dump
[Bluetooth] Reject L2CAP connections on an insecure ACL link
[Bluetooth] Enforce correct authentication requirements
[Bluetooth] Fix reference counting during ACL config stage
This fixes kernel bugzilla 11469: "TUN with 1024 neighbours:
ip6_dst_lookup_tail NULL crash"
dst->neighbour is not necessarily hooked up at this point
in the processing path, so blindly dereferencing it is
the wrong thing to do. This NULL check exists in other
similar paths and this case was just an oversight.
Also fix the completely wrong and confusing indentation
here while we're at it.
Based upon a patch by Evgeniy Polyakov.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clockevents: remove WARN_ON which was used to gather information
The issue of the endless reprogramming loop due to a too small
min_delta_ns was fixed with the previous updates of the clock events
code, but we had no information about the spread of this problem. I
added a WARN_ON to get automated information via kerneloops.org and to
get some direct reports, which allowed me to analyse the affected
machines.
The WARN_ON has served its purpose and would be annoying for a release
kernel. Remove it and just keep the information about the increase of
the min_delta_ns value.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'linux-next' of git://git.infradead.org/~dedekind/ubifs-2.6:
UBIFS: make minimum fanout 3
UBIFS: fix division by zero
UBIFS: amend f_fsid
UBIFS: fill f_fsid
UBIFS: improve statfs reporting even more
UBIFS: introduce LEB overhead
UBIFS: add forgotten gc_idx_lebs component
UBIFS: fix assertion
UBIFS: improve statfs reporting
UBIFS: remove incorrect index space check
UBIFS: push empty flash hack down
UBIFS: do not update min_idx_lebs in stafs
UBIFS: allow for racing between GC and TNC
UBIFS: always read hashed-key nodes under TNC mutex
UBIFS: fix zero-length truncations
It was introduced by "vsprintf: add support for '%pS' and '%pF' pointer
formats" in commit 0fe1ef24f7. However,
the current way its coded doesn't work on parisc64. For two reasons: 1)
parisc isn't in the #ifdef and 2) parisc has a different format for
function descriptors
Make dereference_function_descriptor() more accommodating by allowing
architecture overrides. I put the three overrides (for parisc64, ppc64
and ia64) in arch/kernel/module.c because that's where the kernel
internal linker which knows how to deal with function descriptors sits.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jie Yang at Atheros is getting more directly involved with upstream work
on the atl* drivers. This patch changes the ATL1 entry to ATLX (atl2
support posted to netdev today) and adds him as a maintainer.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the 2.6.27 circle ->fasync lost the BKL, and the last remaining
->open variant that takes the BKL is also gone. ->get_sb and ->kill_sb
didn't have BKL forever, so updated the entries while we're at that.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The commit commit 4c563f7669 ("[XFRM]:
Speed up xfrm_policy and xfrm_state walking") inadvertently removed
larval states and socket policies from netlink dumps. This patch
restores them.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When disconnected ccw devices are removed, the device has to be set
offline, otherwise there will be side effects including a reference
count imbalance. This patch modifies ccw_device_offline to work for
devices in disconnecte/not operational state. ccw_device_offline is
called by cio for devices which are online during device removal.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
ssch() has two classes of return codes:
- condition codes (0-3) which need to be translated to Linux
error codes
- Linux error codes (-EIO on exceptions) which should be passed
to the caller (instead of erronously being handled like
condition code 3)
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>