This patch enables EthernetAVB for r8a77990 Ebisu board.
Based on a patch from Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds EthernetAVB node for r8a77990 (R-Car E3).
Based on a patch from Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds GPIO nodes for r8a77990 (R-Car E3).
Based on a patch from Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[simon: dropped use of deprecated "renesas,gpio-rcar"]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the V3H Starter Kit board.
The board has 1 debug serial port (SCIF0); include support for it,
so that the serial console can work.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When adding the R8A77980 EtherAVB device I failed to notice that it does
not have the usual "status" property disabling the described devices in
anticipation that the board device trees enable the devices according to
their needs. This causes the EtherAVB driver to successfully probe despite
e.g. the needed pins not having been configured -- luckily, "eth<n>" device
can't be opened anyway...
Fixes: bf6f90832f ("arm64: dts: renesas: r8a77980: add EtherAVB support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When adding the R8A77970 EtherAVB device I failed to notice that it does
not have the usual "status" property disabling the described devices in
anticipation that the board device trees enable the devices according to
their needs. This causes the EtherAVB driver to successfully probe despite
e.g. the needed pins not having been configured -- luckily, "eth<n>" device
can't be opened anyway...
Fixes: bea2ab136e ("arm64: dts: renesas: r8a77970: add EtherAVB support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add resets property to CAN-FD node to describe it in the reset topology of
on-SoC devices. This allows to reset the CAN-FD device using the Reset
Controller API.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the performance monitor unit for the Cortex-A53 cores on the
R-Car V3M (r8a77970) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the second Cortex-A53 CPU core on the Renesas
R-Car V3M (r8a77970) SoC, and adjust the interrupt delivery masks for
ARM Generic Interrupt Controller and Architectured Timer.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SDHI nodes to the DT of the r8a77965 SoC.
Based on several similar patches of the R8A7796 device tree
by Simon Horman <horms+renesas@verge.net.au>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On the R-Car Starter Kit Premier/Pro, all of the DDR0, DDR1, DDR0C, and
DDR1C power rails need to be kept powered when backup mode is enabled.
Reflect this in the "rohm,ddr-backup-power" property for the BD9571MWV
PMIC node.
The accessory power switch (SW8) is a momentary switch, hense specify
"rohm,rstbmode-pulse".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On Salvator-X(S), all of the DDR0, DDR1, DDR0C, and DDR1C power rails
need to be kept powered when backup mode is enabled. Reflect this in
the "rohm,ddr-backup-power" property for the BD9571MWV PMIC node.
The accessory power switch (SW23) is a toggle switch, hence specify
"rohm,rstbmode-level".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the ROHM BD9571MWV PMIC.
This was based on the example in the DT binding documentation, but using
IRQ0 instead of a GPIO interrupt, as that matches the schematics, and
because INTC-EX is a simpler block.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add missing spaces after commas.
Replace 8 consecutive spaces by a TAB.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables USB2.0 host channel 3 for r8a7795 with Salvator-XS.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables HS-USB channel3 node for r8a7795 with Salvator-XS.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables usb2_phy3 node for r8a7795 with Salvator-XS.
You must change the SW31 to OFF-OFF-ON-ON-ON-ON on the board.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the EEPROM found on Salvator-X and -XS boards for H3, M3-W, and M3-N
on the IIC_DVFS bus.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Condor board dependent part of the CAN-FD device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77980 part of the CAN-FD device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[simon: consistently use tabs for indentation]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Eagle board dependent part of the CAN-FD device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77970 part of the CAN-FD device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Based on previous work by Ryo Kataoka <ryo.kataoka.wt@renesas.com>.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[simon: moved thermal node to preseve ordering of nodes by bus address]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the hardcoded power domain indices by R8A77965_PD_* symbols.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
[simon: dropped hunk to include r8a77965-sysc.h which is already present]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the commit 7755b40d07 ("dt-bindings: power: add R8A77980 SYSC
power domain definitions") has hit Linus' tree, we can replace the bare
numbers (we had to use to avoid a cross tree dependency) with these macro
definitions...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the commit 35b3c462da ("dt-bindings: clock: add R8A77980 CPG
core clock definitions") has hit Linus' tree, we can replace the bare
numbers (we had to use to avoid a cross tree dependency) with these macro
definitions...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The rcar_sound port nodes have unit names and thus should have register
properties.
This is flagged by dtc as follows:
# make dtbs W=1
...
DTC arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dtb
arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
DTC arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dtb
arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
Prior to this patch the port nodes only defined in board DTS files.
As the register properties are common this patch defines the port nodes
and provides register properties in the SoC DTS file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The rcar_sound port nodes have unit names and thus should have register
properties.
This is flagged by dtc as follows:
# make dtbs W=1
...
DTC arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@1: node has a unit name, but no reg property
...
DTC arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@1: node has a unit name, but no reg property
Prior to this patch the port nodes only defined in board DTS files.
As the register properties are common this patch defines the port nodes
and provides register properties in the SoC DTS file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The rcar_sound port nodes have unit names and thus should have register
properties.
This is flagged by dtc as follows:
# make dtbs W=1
...
DTC arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@1: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@2: node has a unit name, but no reg property
...
DTC arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb
arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@1: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@2: node has a unit name, but no reg property
DTC arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb
arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@1: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@2: node has a unit name, but no reg property
Prior to this patch the port nodes only defined in board DTS files.
As the register properties are common this patch defines the port nodes
and provides register properties in the SoC DTS file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Define the V3M Starter Kit board dependent part of the DU and LVDS device
nodes. Also add the device nodes for Thine THC63LVD1024 LVDS decoder and
Analog Devices ADV7511W HDMI transmitter...
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Condor board dependent part of the MMC0 (connected to eMMC chip)
device node along with the necessary voltage regulators...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU1 external dot clock is provided by the fixed frequency clock
generator X21, while the DU0 and DU3 clocks are provided by the
programmable Versaclock6 clock generator.
Enable the clocks, and the HDMI encoder for the M3-N Salvator-XS, and
hook it up to the HDMI connector
Based on patches from Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU1 external dot clock is provided by the fixed frequency clock
generator X21, while the DU0 and DU3 clocks are provided by the
programmable Versaclock5 clock generator.
Enable the clocks, and the HDMI encoder for the M3-N Salvator-X board
and hook it up to the HDMI connector.
Based on patches from Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the HDMI encoder to the R8A77965 DT in disabled state.
Based on a similar patch of the R8A7796 device tree
by Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Kieran: Rebase to top of tree]
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU entity node has been previously added but only as a placeholder.
Populate the node with the properties to use the device.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a77965 has 4 VSP instances.
Based on a similar patch of the R8A7796 device tree
by Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Kieran: Rebased to top of tree, fixed sort orders]
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The FCPs handle the interface between various IP cores and memory. Add
the instances related to the FDPs and VSP2s.
Based on a similar patch of the R8A7796 device tree
by Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Kieran: Rebase to top of tree]
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The cache controller node should not have unit-addresses and reg
properties. So, this patch removes them.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The basic support patch 9491a8b17530 ("arm64: dts: renesas: Add Renesas
R8A77990 SoC support") lacks the compatible "arm,psci-1.0" in the psci
node. So, this patch revises it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove 'status = "disabled"' to make sure all IPMMU devices are enabled
in DT on the r8a7795 ES1.0 Soc.
This is a follow up for a patch by Magnus Damm for the
the r8a7795 ES2.0 and other R-Car Gen 3 SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current Sound is using simple-audio-card which can't support HDMI.
To use HDMI sound, we need to use audio-graph-card.
But, one note is that r8a7795 has 2 HDMI ports, but r8a7796 has 1.
Because of this mismatch, supporting HDMI on salvator-common is
impossible.
Thus, this patch exchange sound card to audio-graph-card and keep
supporting ak4613 as 1st sound node.
r8a7795/r8a7796 salvator-x{s} need to add HDMI sound individually.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Yoshihiro Shimoda
Sergei Shtylyov
Jacopo Mondi
Simon Horman
Geert Uytterhoeven
Takeshi Kihara
Wolfram Sang
Niklas Söderlund
Kieran Bingham
Kuninori Morimoto