v4l2_subdev_link_validate_get_format() retrieves the remote pad format
depending on the entity type and prints a warning if the entity type is
not supported. The type check doesn't take the subtype into account, and
thus always prints a warning for device node types, even when supported.
Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set "y_skip_top" to zero and revise comment as I do not see this line
corruption on two different mt9v022 setups. The first read-out line
is perfectly fine. Add mt9v022 platform data configuring y_skip_top
for platforms that have issues with the first read-out line. Set
y_skip_top to 1 for pcm990 board.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some camera systems cannot operate mt9v022 in normal mode and use
only the snapshot mode. The TechNote for mt9v022 (TN0960) and mt9v024
(TN-09-225) describes required register settings when configuring the
snapshot operation. The snapshot mode requires that certain automatic
functions of the image sensor should be disabled or set to fixed values.
According to the TechNote bit 2 and bit 9 in the register 0x20 must be
set in snapshot mode and unset for normal operation. This applies for
mt9v022 Rev.3 and mt9v024. Add required reg. 0x20 settings dependent on
sensor chip version.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add controls for horizontal and vertical blanking. Also add an error
message for case that the control handler init failed. Since setting
the blanking registers is done by controls now, we shouldn't change
these registers outside of the control function. Use v4l2_ctrl_s_ctrl()
to set them.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the result of experimenting with the SpeedLink VAD Laplace webcam.
The register sequence for V4L2_MBUS_FMT_YUYV8_2X8 has been identified by
analyzing USB-logs of this device running on MS Windows.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Try reading on video device. If the camera bus driver supports reading
we can try it and return the result. Also add a debug line.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mx1_camera driver has been broken for a few release cycles since
commit 6bd0812 (dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c).
It seems there is no one even compile tested it since then, as doing
so will end up with the following error.
CC drivers/media/platform/soc_camera/mx1_camera.o
In file included from drivers/media/platform/soc_camera/mx1_camera.c:44:0:
arch/arm/mach-imx/include/mach/dma-mx1-mx2.h:8:25: fatal error: mach/dma-v1.h: No such file or directory
It seems there is no one being interested in bringing it back to
work [1] so far. Let's mark it BROKEN.
[1] https://lkml.org/lkml/2012/2/9/171
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This should have break statements in it.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The winbond hardware has a counter for leading edges, which increases as
they are received. As we read raw IR from a fifo in an interrupt handler,
we cannot correlate them to specific IR pulses so we simply count all
pulses and edges until we go idle and disable the receiver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The receiver is never disabled by idle mode since rxstate never gets set
to RXSTATE_ACTIVE, so we keep on getting interrupts after the first IR
activity ends. Note that ir_raw_event_reset() already calls
ir_raw_event_handle().
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sparse warning is:
"drivers/media/usb/stkwebcam/stk-webcam.c:59:5:
warning: symbol 'first_init' was not declared. Should it be static?"
Declare variable 'first_init' as static and local to the function.
Found by Hans Verkuil's daily build. Tested by compilation only.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds an entry in MAINTAINERS file for
TI Davinci media drivers.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds MAINTAINERS entry for radio-mr800 usb radio driver.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
And the smiapp-pll which is in a way part of the smiapp driver.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As a first step towards migrating davinci platforms to use common clock
framework, replace all instances of clk_enable() with clk_prepare_enable()
and clk_disable() with clk_disable_unprepare().
Also fixes some issues related to clk clean up in the driver
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
set device_caps and also change the driver and
bus_info to proper values as per standard.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Warnings were generated because of the following commit changed data type for
address pointer
195bbca ARM: 7500/1: io: avoid writeback addressing modes for __raw_ accessors
add __iomem annotation to fix following warnings
drivers/media/platform/davinci/vpbe_osd.c: In function ‘osd_read’:
drivers/media/platform/davinci/vpbe_osd.c:49:2: warning: passing
argument 1 of ‘__raw_readl’ makes pointer from integer without a cast [enabled by default]
arch/arm/include/asm/io.h:104:19: note: expected ‘const volatile
void *’ but argument is of type ‘long unsigned int’
This patch stores the ioremap_nocache() returned address in a
void __iomem * instead of a unsigned long and passes the same to
readl/writel functions which fixes the above warnings.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update contact information to correspond my e-mail address changes.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
fixed below checkpatch error.
- ERROR: that open brace { should be on the previous line
Signed-off-by: YAMANE Toshiaki <yamanetoshi@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
fixed below checkpatch error.
- ERROR: that open brace { should be on the previous line
Signed-off-by: YAMANE Toshiaki <yamanetoshi@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
fixed below checkpatch error.
- ERROR: that open brace { should be on the previous line
Signed-off-by: YAMANE Toshiaki <yamanetoshi@gmail.com>
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently used registers 0xc5 and 0xc7 provide only a very coarse
adjustment possibility within a very small value range (0-3).
With registers 0x01 and 0x03, a fine grained adjustment with
255 steps is possible. This is also what the Windows driver does.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
R,G,B balance registers are 0x01-0x03 instead of 0x02-0x04,
which lead to the wrong conclusion that values are inverted.
Exposure is controlled via page 3 registers and this is already documented.
Also fix a whitespace issue.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Many people are trying to use stk1160 on low memory devices.
Instead of failing if one allocation fails, we allow the driver
to continue working if fewer transfer buffers are available.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Usage of TSTAMP_* macros has gone in 2010 in 730947bc (V4L/DVB: vivi:
clean up and a major overhaul) but the macros remain. Say goodbye to
them.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Stephen:
After merging the v4l-dvb tree, today's linux-next build (x86_64
allmodconfig) failed like this:
ERROR: "sms_ir_exit" [drivers/media/common/siano/smsmdtv.ko] undefined!
ERROR: "sms_ir_event" [drivers/media/common/siano/smsmdtv.ko] undefined!
ERROR: "sms_ir_init" [drivers/media/common/siano/smsmdtv.ko] undefined!
The smsir file should be part of the smsmdtv core, if RC is defined.
Fix it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Antti and by Stephen:
drivers/built-in.o: In function `sms_ir_event':
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:48: undefined reference to `ir_raw_event_store'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:50: undefined reference to `ir_raw_event_handle'
drivers/built-in.o: In function `sms_ir_init':
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:56: undefined reference to `smscore_get_board_id'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:60: undefined reference to `rc_allocate_device'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:72: undefined reference to `sms_get_board'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:92: undefined reference to `sms_get_board'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:97: undefined reference to `rc_register_device'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c💯 undefined reference to `rc_free_device'
drivers/built-in.o: In function `sms_ir_exit':
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:111: undefined reference to `rc_unregister_device'
make: *** [vmlinux] Error 1
Caused by commit fdd1eeb49d "[media] siano: allow compiling it without RC support"
And it happens when CONFIG_SMS_SIANO_RC=y and CONFIG_RC_CORE=m .
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is currently discussion to add MAINTAINERS records for media
drivers that don't have one yet, possibly with 'orphan' or 'odd fixes'
status. Here is a proper entry for the firedtv driver (for 1394
attached DVB STBs and 1394 attached DVB cards from Digital Everywhere).
The L: linux-media and T: linux-media.git lines in this entry are
redundant to what scripts/get_maintainer.pl would show automatically but
I added them for folks who read MAINTAINERS directly. The "(firedtv)"
string is for those folks as well if they look for driver name rather
than file path.
The F: drivers/media/firewire/ pattern and the "FireWire media drivers"
title are currently synonymous with firedtv. If more drivers get added
there, this can be revisited.
I don't have documentation or DVB-S2 devices to test, but I have DVB-C
and DVB-T devices for testing.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those two tuners were always maintained. As I have devices with
tea5767, this is marked as Maintained.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While this file was always maintained, there was no explicit entry
for it.
There aren't many things happening at tm6000 side for a long time:
Driver works. This chip is already not sold anymore, so I don't
expect much changes on its side.
So, add a new entry with status equal to Odd fixes to better
reflect it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While this file was always maintained, there was no explicit entry
for it.
There aren't many things happening at saa7134 side for a long time:
Driver works, and it is stable. When new patches are submitted,
they're new boards addition for hardware I don't have.
So, add a new entry with status equal to Odd fixes to better
reflect it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart
Anatolij Gustschin
Frank Schäfer
Shawn Guo
Alan Cox
Shubhrajyoti D
Sean Young
Ezequiel Garcia
Lad, Prabhakar
Alexey Klimov
Sylwester Nawrocki
Sakari Ailus
Murali Karicheri
YAMANE Toshiaki
Hans de Goede
Kirill Smelkov
Mauro Carvalho Chehab
Malcolm Priestley
Stefan Richter