Otherwise we get the following error with omap3_defconfig and CONFIG_SMP:
Error: selected processor does not support `sev'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This patch extends the ASoC API to allow sound cards to have more than one
CODEC and more than one platform DMA controller. This is achieved by dividing
some current ASoC structures that contain both driver data and device data into
structures that only either contain device data or driver data. i.e.
struct snd_soc_codec ---> struct snd_soc_codec (device data)
+-> struct snd_soc_codec_driver (driver data)
struct snd_soc_platform ---> struct snd_soc_platform (device data)
+-> struct snd_soc_platform_driver (driver data)
struct snd_soc_dai ---> struct snd_soc_dai (device data)
+-> struct snd_soc_dai_driver (driver data)
struct snd_soc_device ---> deleted
This now allows ASoC to be more tightly aligned with the Linux driver model and
also means that every ASoC codec, platform and (platform) DAI is a kernel
device. ASoC component private data is now stored as device private data.
The ASoC sound card struct snd_soc_card has also been updated to store lists
of it's components rather than a pointer to a codec and platform. The PCM
runtime struct soc_pcm_runtime now has pointers to all its components.
This patch adds DAPM support for ASoC multi-component and removes struct
snd_soc_socdev from DAPM core. All DAPM calls are now made on a card, codec
or runtime PCM level basis rather than using snd_soc_socdev.
Other notable multi-component changes:-
* Stream operations now de-reference less structures.
* close_delayed work() now runs on a DAI basis rather than looping all DAIs
in a card.
* PM suspend()/resume() operations can now handle N CODECs and Platforms
per sound card.
* Added soc_bind_dai_link() to bind the component devices to the sound card.
* Added soc_dai_link_probe() and soc_dai_link_remove() to probe and remove
DAI link components.
* sysfs entries can now be registered per component per card.
* snd_soc_new_pcms() functionailty rolled into dai_link_probe().
* snd_soc_register_codec() now does all the codec list and mutex init.
This patch changes the probe() and remove() of the CODEC drivers as follows:-
o Make CODEC driver a platform driver
o Moved all struct snd_soc_codec list, mutex, etc initialiasation to core.
o Removed all static codec pointers (drivers now support > 1 codec dev)
o snd_soc_register_pcms() now done by core.
o snd_soc_register_dai() folded into snd_soc_register_codec().
CS4270 portions:
Acked-by: Timur Tabi <timur@freescale.com>
Some TLV320aic23 and Cirrus platform fixes.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
TI CODEC and OMAP fixes
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Samsung platform and misc fixes :-
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
MPC8610 and PPC fixes.
Signed-off-by: Timur Tabi <timur@freescale.com>
i.MX fixes and some core fixes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
J4740 platform fixes:-
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
CC: Tony Lindgren <tony@atomide.com>
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
CC: Kuninori Morimoto <morimoto.kuninori@renesas.com>
CC: Daniel Gloeckner <dg@emlix.com>
CC: Manuel Lauss <mano@roarinelk.homelinux.net>
CC: Mike Frysinger <vapier.adi@gmail.com>
CC: Arnaud Patard <apatard@mandriva.com>
CC: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This will allow us to set up special cards in machine drivers just after
they are detected by MMC core.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Kalle Valo <kvalo@adurom.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (214 commits)
ALSA: hda - Add pin-fix for HP dc5750
ALSA: als4000: Fix potentially invalid DMA mode setup
ALSA: als4000: enable burst mode
ALSA: hda - Fix initial capsrc selection in patch_alc269()
ASoC: TWL4030: Capture route runtime DAPM ordering fix
ALSA: hda - Add PC-beep whitelist for an Intel board
ALSA: hda - More relax for pending period handling
ALSA: hda - Define AC_FMT_* constants
ALSA: hda - Fix beep frequency on IDT 92HD73xx and 92HD71Bxx codecs
ALSA: hda - Add support for HDMI HBR passthrough
ALSA: hda - Set Stream Type in Stream Format according to AES0
ALSA: hda - Fix Thinkpad X300 so SPDIF is not exposed
ALSA: hda - FIX to not expose SPDIF on Thinkpad X301, since it does not have the ability to use SPDIF
ASoC: wm9081: fix resource reclaim in wm9081_register error path
ASoC: wm8978: fix a memory leak if a wm8978_register fail
ASoC: wm8974: fix a memory leak if another WM8974 is registered
ASoC: wm8961: fix resource reclaim in wm8961_register error path
ASoC: wm8955: fix resource reclaim in wm8955_register error path
ASoC: wm8940: fix a memory leak if wm8940_register return error
ASoC: wm8904: fix resource reclaim in wm8904_register error path
...
Currently the update area on manual update displays is automatically
enlargened to fully cover scaled overlays. This patch makes that
optional, allowing the panel driver to choose if it's used or not.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Remove kernel.h and module.h since they are not used correctly anyway.
Also, remove device.h since it comes along with platform_device.h
(always will I guess).
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
No need to dynamically register mailboxes one by one.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
With this patch, you'll get the following sysfs directories. This
structure implies that a single platform device, "omap2-mailbox" holds
multiple logical mbox instances. This could be the base to add sysfs
files for each logical mboxes. Then userland application can access a
mbox through sysfs entries if necessary(ex: setting kfifo size
dynamically)
~# tree -d -L 2 /sys/devices/platform/omap2-mailbox/
/sys/devices/platform/omap2-mailbox/
|-- driver -> ../../../bus/platform/drivers/omap2-mailbox
|-- mbox
| |-- dsp <- they are each instances of logical mailbox.
| |-- ducati
| |-- iva2
| |-- mbox01
| |-- mbox02
| |-- mbox03
| |-- .....
| `-- tesla
|-- power
`-- subsystem -> ../../../bus/platform
This was wrongly dropped by:
commit c7c158e57b
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
The underlying buffering implementation of mailbox
is converted from block API to kfifo due to the simplicity
and speed of kfifo.
The default size of the kfifo buffer is set to 256 bytes.
This value is configurable at compile time (via
CONFIG_OMAP_MBOX_KFIFO_SIZE), and can be changed at
runtime (via the mbox_kfifo_size module parameter).
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
rwlocks are slower and have potential starvation issues
therefore spinlocks are generally preferred.
see also: http://lwn.net/Articles/364583/
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Kanigeri Hari <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
when blk_get_request fails to get the request it is returning
without read the message from the mailbox fifo, then when it
leaves the isr and interruption is trigger again and again and
the workqueue which get elements from the request queue is never
executed and the kernel is stuck and shows a softlockup message.
Now the mailbox interrupt is disabled when request queue is full
and enabled when it pop a elememt form the request queue.
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
mailbox startup and shutdown are being executed against
a single H/W module, and a mailbox H/W module is totally
__independent__ of the registration of logical mailboxes.
So, an independent mutext should be used for startup and
shutdown.
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
This patch checks if the mailbox user has assinged a valid
callback fuction before calling it.
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
flush pending deferred works before freeing blk_queue to prevent
any attempt of access to blk_queue after it was freed
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Free interrupt before freeing blk_queue to avoid
any attempt of access to blk_queue after it was freed.
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Add revision detection for ES1.1 and ES1.2. Set default
revision as ES1.2.
Add CHIP_GE_OMAP3630ES1_1 to detect revisions 1.1 and later.
This is needed for at least one feature that is broken in
3630ES1.0 but exists on older (3430 ES3.1) and newer revisions.
Additionally, update some of the CHIP_GE_* macros to use other
macros for ease of maintenance.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Manjunatha GK <manjugk@ti.com>
[tony@atomide.com: update to remove fallthrough handling]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Do not forget to check the 'platform_device_add_data()' error code
in 'omap_device_build_ss()'.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most OMAP3-based boards use exactly the same code for .map_io method in
the machine_desc structure.
This patch introduces omap3_map_io and updates board-* files to use it
as .map_io method.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The only difference between them is the physical address of the
uart4 port, which is only present in 36xx chips.
We don't really need to care about keeping these 2 functions, since
the decision to use uart4 is more cleanly done later when we do have
access to omap_revision variable.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: added comment for the uart4_phys]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Introduce a configuration struct for platform/board specific information
of Nokia DSI command mode panels, to be used in addition to struct
omap_dss_device (passed via the 'void *data' member).
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
This patch removes direct reference of gpmc address from generic nand platform code.
Nand platform code now uses wrapper functions which are implemented in gpmc module.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
few functions added in gpmc module and to be used by other drivers like NAND.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3505/3517 doesn't have IO wakeup capability, so we do not need to set
the bit OMAP3430_EN_IO and the bit OMAP3430_EN_IO_CHAIN in the register
PM_WKEN_WKUP when the system enters suspend state.
Tested on AM3517EVM and OMAP3530EVM.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Omap DMA controller can prefetch data in advance in case of
destination synchronized data transfer. This may increase
performance when target HW block doesn't have fifo.
Data is waiting for transfer request in DMA fifo instead of read from memory.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix GPIO numbers and smc91x for 2430sdp. The earlier code
had cut and paste errors from 3430sdp code. Also, 2430
has five GPIO banks for a total of 160 GPIO lines.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change adds in the necessary clocks and mux pins for UART
control on omap7xx devices. I also made a change in the serial
code to only try and initialize two UARTs in omap_serial_init, as
these devices don't have three.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Recent DEBUG_LL and uncompress.h changes removed the check_port()
as pointed out by Cory Maccarrone <darkstar6262@gmail.com>.
This causes some boards to not boot, so add back the MDR1 register
check. The MDR1 register tells the mode of omap uart. Based on
an earlier patch by Cory Maccarrone <darkstar6262@gmail.com>.
Tested-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds a secure API to read AuxCoreBoot0 register to
check the cpu boot status. It also moves the other smc APIs
to common omap44xx-smc.S. This APIs should not be marked as
__INIT because we need these to be present for CPU hotplug
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add omap_pm_set_min_clk_rate(). This constraint is meant for use by
device drivers to translate a certain device-specific performance
constraint (e.g., "minimum polygons per second") to a clock rate for
the driver's device, given the driver's intimate knowledge of the
device hardware (e.g., device type, device hardware revision, firmware
revision, etc.) From a general PM core perspective, clock rate is
probably the closest general analog to "performance" that is
available, but the exact mapping from a use-case-specific performance
constraint to clock rate must be done by the driver. Drivers intended for
upstream merging shouldn't hardcode specific clock rates in their code
without basing those rates on some performance criteria requested through
the driver's subsystem (ideally, from userspace).
Imre Deak <imre.deak@nokia.com> described the need and use-case for
this constraint, and discussed the implementation - thanks, Imre.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Imre Deak <imre.deak@nokia.com>
Add return values to the PM constraint functions. This allows the PM
core to provide feedback to the caller if a constraint is not
possible. Update the one upstream user of omap_pm_set_max_mpu_wakeup_lat()
to add a compatibility wrapper, needed until the driver is changed.
Update some of the documentation to conform more closely to kerneldoc style.
Add an additional device parameter to omap_pm_set_max_dev_wakeup_lat()
to identify the device requesting the constraint. This is so repeated calls
to omap_pm_set_max_dev_wakeup_lat() with the same requesting device can
override the device's previously-set constraint. Also, it allows the PM
core to make a decision as to whether or not the constraint should be
satisfied, based on the caller's identity.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Update some minor documentation issues and update copyright for
omap_device/omap_hwmod code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Add omap_device_get_mpu_rt_va(). This is intended to be used by
device drivers (currently, via a struct platform_data function
pointer) to retrieve their corresponding device's virtual base address
that the MPU should use to access the device. This is needed because
the omap_hwmod code does its own ioremap(), in order to gain access to
the module's OCP_SYSCONFIG register.
Add omap_hwmod_get_mpu_rt_va(). omap_device_get_mpu_rt_va() calls this
function to do the real work.
While here, rename struct omap_hwmod._rt_va to struct
omap_hwmod._mpu_rt_va, to reinforce that it refers to the MPU's
register target virtual address base (as opposed to, for example, the
L3's).
In the future, this belongs as a function in an omap_bus, so it is not
necessary to call this through a platform_data function pointer.
The use-case for this function was originally presented by Santosh
Shilimkar <santosh.shilimkar@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Create simple omap_devices for the main processors and busses.
This is required to support the forth-coming device-based OPP
approach, where OPPs are managed and tracked at the device level.
Also, move these common PM init functions into a common_pm_init call
that is called as a device_initcall(). The PM init is done at this level
to ensure that the driver core is initialized before initialized.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[paul@pwsan.com: sparse warnings cleaned up; newly-created functions moved
from mach-omap2/io.c to mach-omap2/pm.c; newly-created functions renamed
to start with "omap2" rather than "omap"]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The omap_hwmod struct has a field to track the omap_device that is
attached to it, but it was not being assigned. Fix by assigning omap_device
pointer when omap_device is built.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[paul@pwsan.com: use an array index rather than pointer arithmetic]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Enable omap_device layer support for OMAP4, so that drivers can
use them to enable/idle/shutdown devices.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On kernels that don't use the omap_device_enable() calls to enable
devices, leave all on-chip devices enabled in hwmod _setup().
Otherwise, accesses to those devices are likely to fail, crashing the
system. It's expected that kernels built without CONFIG_PM_RUNTIME
will be the primary use-case for this. This functionality is
controlled by adding an extra parameter to omap_hwmod_late_init().
This patch is based on the patch "OMAP: hwmod: don't auto-disable
hwmod when !CONFIG_PM_RUNTIME" by Kevin Hilman
<khilman@deeprootsystems.com>.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some hwmods may need to be idled/enabled in atomic context, so
non-locking versions of these functions are required.
Most users should not need these and usage of theses should be
controlled to understand why access is being done in atomic context.
For this reason, the non-locking functions are only exposed at the
hwmod level and not at the omap-device level.
The use-case that led to the need for the non-locking versions is
hwmods that are enabled/idled from within the core idle/suspend path.
Since interrupts are already disabled here, the mutex-based locking in
hwmod can sleep and will cause potential deadlocks.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add kerneldoc for struct clk, struct clksel_rate, struct clksel. Move
flag macros for struct clk.flags and struct clksel_rate.flags closer
to the structures.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The logic in this file is rather convoluted, but essentially:
1. region type 0 is SDRAM
2. referring to the code fragment
if (set_fbmem_region_type(&rg, OMAPFB_MEMTYPE_SDRAM,
sdram_start, sdram_size) < 0 ||
(rg.type != OMAPFB_MEMTYPE_SDRAM))
continue;
- if rg.type is not OMAPFB_MEMTYPE_SDRAM, set_fbmem_region_type()
returns zero immediately (since rg.type is non-zero), and so we
'continue'.
- if rg.type is OMAPFB_MEMTYPE_SDRAM, and rg.paddr is zero,
we fall through.
- if rg.type is OMAPFB_MEMTYPE_SDRAM, and the region lies within
SDRAM, we fall through.
- if rg.type is OMAPFB_MEMTYPE_SDRAM, and the region is not within
SDRAM, we 'continue'.
3. check_fbmem_region seems unnecessary.
- we know rg.type is OMAPFB_MEMTYPE_SDRAM
- we can check rg.size independently
- bootmem_reserve() can check for overlapping reservations itself
- we've already validated that the requested region lies within SDRAM.
4. avoid BUG()ing if the region entry is already set; print an error,
and mark the configuration invalid - at least we'll continue booting
so the error message has a chance of being logged/visible via serial
console.
With these changes in place, it makes the code much easier to understand
and hence easier to convert to LMB.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
LEDS_OMAP_DEBUG doesn't exist in Kconfig, therefore replacing all
references for it with OMAP_DEBUG_LEDS from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_DSP doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
[tony@atomide.com: updated to apply on top of already queued patches]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we get pin muxing out of plat-omap and can convert H4 to use the
new mux functions.
Note that it should be safe to assume we can mux all the keypad pins
except on H4 which may have Menelaus connected.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move omap2 FS USB platform init code into mach-omap2/usb-fs.c. This will
allow further work later on to use omap hwmod for initializing the
device.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to split old FS USB platform init code and stop doing pin multiplexing
under plat-omap. First move 24xx specific init code into omap2_usb[012]_init
functions.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The function prefix "omap2_iommu_" indicates that the prefixed
function belongs to "omap2_iommu_ops" to provide iommu basic
functionalities for the above layers. It's better to avoid the
prefixed function called in the same prefixed ones internally, like
nested here. Now "iommu_disable" is called just after fault_isr() in
the above layer. This is a little bit more sensible to keep the
consistency of module layers.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
In order to enable TLB miss interrupt, the TWL should be
disabled. This patch provides the functionality to get the
MMU fault interrupt for a TLB miss in the cases where the
users are working with the locked TLB entries and with TWL
disabled.
New interface is added to select twl and to enable TLB miss
interrupt.
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Ramesh Gupta <grgupta@ti.com>
Signed-off-by: Hiroshi Doyu <Hiroshi.DOYU@nokia.com>
The addition of the new debounce code (commit
168ef3d9a5) broke the auto-disable of
debounce clocks on idle by forgetting to update the debounce clock
enable mask.
Add back the updating of bank->dbck_enable_mask so debounce clocks are
auto-disabled.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The kernel timer queue is being run currently from a GP timer running in a one
shot mode, which works in a way that when it expires, it will also stop.
Usually during this situation, the interrupt handler will ack the interrupt,
load a new value to the timer and start it again. During suspend, the
situation is slightly different, as we disable interrupts just before
timekeeping is suspended, which leaves a small window where the timer can
expire before it is stopped, and will leave the interrupt flag pending.
This pending interrupt will prevent ARM sleep entry, thus now we ack it always
when we are attempting to stop a timer.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: removed the ifdef to make the patch cover omap1 also]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The memory allocated for sgt structure is not freed on error
when sg_alloc_table is called in sgtable_alloc().
Signed-off-by: Satish Kumar <x0124230@ti.com>
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Cc: Vimal Singh <vimal.newwork@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgen <tony@atomide.com>
Sicne the platform data's buffer_size now holds the full size
of the FIFO, there is no longer need to handle the ports
differently.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolsfonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Use the actual FIFO size in words as buffer_size on OMAP3.
Change the threshold configuration to use 1 based numbering, when
specifying the allowed threshold maximum or the McBSP threshold value.
Set the default maximum threshold to (buffer_size - 0x10) intialy.
>From users of McBSP, now it is expected to use this method.
Asking for threshold 1 means that the value written to threshold registers
are going to be 0, which means 1 word threshold.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolsfonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Users of McBSP can use the omap_mcbsp_get_fifo_size function to query
the size of the McBSP FIFO.
The function will return the FIFO size in words (the HW maximum).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolsfonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Nobody uses that anymore, so remove and expect drivers to use the gpiolib
implementation.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OMAP supports debouncing of gpio lines, implement the method using
gpiolib.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (113 commits)
omap4: Add support for i2c init
omap: Fix i2c platform init code for omap4
OMAP2 clock: fix recursive spinlock attempt when CONFIG_CPU_FREQ=y
OMAP powerdomain, hwmod, omap_device: add some credits
OMAP4 powerdomain: Support LOWPOWERSTATECHANGE for powerdomains
OMAP3 clock: add support for setting the divider for sys_clkout2 using clk_set_rate
OMAP4 powerdomain: Fix pwrsts flags for ALWAYS ON domains
OMAP: timers: Fix clock source names for OMAP4
OMAP4 clock: Support clk_set_parent
OMAP4: PRCM: Add offset defines for all CM registers
OMAP4: PRCM: Add offset defines for all PRM registers
OMAP4: PRCM: Remove duplicate definition of base addresses
OMAP4: PRM: Remove MPU internal code name and apply PRCM naming convention
OMAP4: CM: Remove non-functional registers in ES1.0
OMAP: hwmod: Replace WARN by pr_warning for clockdomain check
OMAP: hwmod: Rename hwmod name for the MPU
OMAP: hwmod: Do not exit the iteration if one clock init failed
OMAP: hwmod: Replace WARN by pr_warning if clock lookup failed
OMAP: hwmod: Remove IS_ERR check with omap_clk_get_by_name return value
OMAP: hwmod: Fix wrong pointer iteration in oh->slaves
...
Add platform init code for the OMAP3 OHCI driver.
Also, configure padconf settings for OMAP3 depending
on which port mode is used.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
EXTVBUS programming is required by OMAP3EVM REV >=E to supply 500mA
power so adding a flag which can be used by musb driver to program
EXTVBUS.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for i2c init for omap4.
This patch is based on and earlier patch by
Santosh Shilimkar <santosh.shilimkar@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add separate omap_i2c_add_bus functions for mach-omap1
and mach-omap2. Make the mach-omap2 init set the interrupt
dynamically to support.
This is needed to add support for omap4 in a way that
works with multi-omap builds. This will eventually get
fixed in a generic way with the omap hwmods.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add some missing credits for people who have contributed significant features
or fixes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Thara Gopinath <thara@ti.com>
Some powerdomains in OMAP4 support a direct transition from one sleep
state to another deeper sleep state without having to wakeup the
powerdomain. This patch adds an api in the powerdomain framework to
set the LOWPOWERSTATECHANGE bit in PWRSTCTRL register.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The pwrsts flag for ALWAYS ON domains like always_on_core_pwrdm
and wkup_pwrdm is wrongly populated with the define for a
powerdomain power state, instead of the allowable state
bitfields.
This causes a few api's to fail sensing invalid pwrst
requested.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The clock sources for timers on OMAP4 (system clock and 32k
clock) have their names wronly populated.
This patch fixes them so the omap_dm_timer_set_source
does not fail anymore.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove the hack put in place while clock framework was still not in
place for OMAP4.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The MPU subsystem was named based on internal code name (CHIRON).
This patch will remove all the occurences of the chiron name
are replace it with PRCM_MPU in order to differentiate
the MPU local PRCM to the global one.
Remove PDA_ from PRCM_MPU registers names to stick to the global
PRM naming convention.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Some initiator modules in OMAP2 & 3 does not have IDLEST bit,
in that case we cannot detect the module readiness by
polling that bit and must exist the function immediately
assuming that the module is ready.
The previous flag was affected to the OCP interface. While it is
technically true that the idlest is related to the L4 slave
interface of the module, the PRCM status belong to the module.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Accessing the clkctrl register using offset of module & device is hard
to do in OMAP4 due to the way the CM1, CM2, PRM and PRCM_MPU are located
in the address space. There is no common base address anymore for all the
CM registers.
The easiest way to handle that on OMAP4 is to provide the absolute address
of the XXX_CLKCTRL register per hwmod.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Clean up comment style, remove unnecessary includes, and resolve some
checkpatch warnings in plat-omap/clock.c.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rename the RATE_IN_343X clksel_rate.rate flag to be RATE_IN_3XXX, to reflect
that these rates are valid on all OMAP3 platforms, not just 343X.
Also rename the RATE_IN_OMAP3430ES2 clksel_rate.rate flag to be
RATE_IN_OMAP3430ES2PLUS, to reflect that these flags are valid on all
OMAP3 platforms after 3430ES2.
This patch should not result in any functional changes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
The DEFAULT_RATE clksel_rate flag is essentially useless. It was set
on some of the lowest divisors, which, when switching to a much
higher-rate parent, could have potentially resulted in rates that
exceeded the hardware specifications for downstream clocks in the
window between the clk_set_parent(), and a subsequent clk_set_rate().
It seems much safer to just remove the flag and always use the highest
available divisor (resulting in the lowest possible rate) after the
switch, and this patch does so.
Ideally, it would be best to first attempt to switch to a divisor that
matches the clock's rate with the previous parent, if at all possible.
But that is a project for some other day or some other person. The
parent changing code is rarely used.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In OMAP4, MMC1 PBIAS and its associated IO is software-controlled
by CONTROL_PBIAS and CONTROL_MMC1 registers. This patch adds PBIAS
configuration for MMC1 Controller during power-ON and power-OFF
of regulator.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Access to some of the OMAP4 GPIO registers are not properly handled.
This patch fixes it.
This patch is tested on 3430SDP and 4430SDP boards
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves OMAP4 soc specific code from 4430sdp board file.
The change is necessary so that newer board support can be added
with minimal changes. This will be also problematic for
multi-board, multi-omap builds.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3517 don't have the register OMAP343X_CONTROL_PBIAS_LITE and the regulators
like "vmmc", so we set a noop "set_power" function for it.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Multi line comments are fixed as per CodingStyle
guidelines.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If we are softbooting another kernel using kexec, DMA controller state is not
known when we are performing omap_init_dma(). It is possible that some DMA
channels are already active. For example after kexec we get:
<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5
To prevent any weird things happening, we disable all channel interrupts during
init.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (250 commits)
ALSA: hda: Storage class should be before const qualifier
ASoC: tpa6130a2: Remove CPVSS and HPVdd supplies
ASoC: tpa6130a2: Define output pins with SND_SOC_DAPM_OUTPUT
ASoC: sdp4430 - add sdp4430 pcm ops to DAI.
ASoC: TWL6040: Enable earphone path in codec
ASoC: SDP4430: Add support for Earphone speaker
ASoC: SDP4430: Add sdp4430 machine driver
ASoC: tlv320dac33: Avoid powering off while in BIAS_OFF
ASoC: tlv320dac33: Use dev_dbg in dac33_hard_power function
ALSA: sound/pci/asihpi: Use kzalloc
ALSA: hdmi - dont fail on extra nodes
ALSA: intelhdmi - add id for the CougarPoint chipset
ALSA: intelhdmi - user friendly codec name
ALSA: intelhdmi - add dependency on SND_DYNAMIC_MINORS
ALSA: asihpi: incorrect range check
ALSA: asihpi: testing the wrong variable
ALSA: es1688: add pedantic range checks
ARM: McBSP: Add support for omap4 in McBSP driver
ARM: McBSP: Fix request for irq in OMAP4
OMAP: McBSP: Add 32-bit mode support
...
While waiting for completion of the i2c transfer, the
MPU could hit OFF mode and cause several msecs of
delay that made i2c transfers fail more often. The
extra delays and subsequent re-trys cause i2c clocks
to be active more often. This has also an negative
effect on power consumption.
Created a mechanism for passing and using the
constraint setting function in driver code. The used
mpu wake up latency constraints are now set individually
per bus, and they are calculated based on clock rate
and fifo size.
Thanks to Jarkko Nikula, Moiz Sonasath, Paul Walmsley,
and Nishanth Menon for tuning out the details of
this patch.
Updates by Kevin as requested by Tony:
- Remove omap_set_i2c_constraint_func() in favor of conditionally
adding the flag in omap_i2c_add_bus() in order to keep all the OMAP
conditional checking in a single location.
- Update set_mpu_wkup_lat prototypes to match OMAP PM layer so
OMAP PM function can be used directly in pdata.
Cc: Moiz Sonasath <m-sonasath@ti.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
McBSP module in OMAP4 needs to be able to set its tx/rx threshold
and enable the transmitter/receiver when starting an audio stream.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In OMAP4, there is only one irq line for TX and RX paths. Use
the correct irq line to avoid errors at runtime.
Also, request irq line only once (instead of requesting for TX
and RX).
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This rejects unaligned device virtual address('da') and physical
address('pa') and informs error to caller when a page table entry is
set. Otherwise, a wrong address can be used by IO device.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: Hari Kanigeri <h-kanigeri2@ti.com>
Searching avaialable spaces should be stopped as soon as it turns out
that there's no possibility with the rest of it.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Inserting a gap page between IOVMAs could detect an override on other
IOVMA with iommu fault. This was originally suggested by Sakari Ailus
and based on the work and comment by David Cohen.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: David Cohen <david.cohen@nokia.com>
Cc: Sakari Ailus <Sakari.Ailus@nokia.com>
This CONFIG_OMAP_IOMMU_DEBUG option cannot be selected because it's
not visible on menu. Make this option selectable.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
There are some places to scan iotlb entries. This iteration macro
could make these code a bit simpler with proceeding iotlb entries
transparently.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Tested-by: Hari Kanigeri <h-kanigeri2@ti.com>
This patch adds TLB preservation support to IOMMU module
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
This patch provides the iommu support for OMAP4 co-processors.
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
The generic gpiolib provides a debugfs interface to GPIOs which
provides identical (but nicer looking) data as the OMAP specific one.
This patch completely drops the OMAP specific interface
(/debug/omap_gpio) in favor of using the generic one (/debug/gpio.)
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
setwkuena and setdataout are covered already by wake_en and dataout fields.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Ensure GPIO debounce clocks are disabled when idle. Otherwise,
clocks will prevent PER powerdomain from entering retention.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently, the GPIO 'prepare' hook is only called when going to
off-mode, while the function is called 'prepare_for_retention.' This
patch renames the function to 'prepare_for_idle' and calls it for any
powersate != PWRDM_POWER_ON passing in the powerstate.
The hook itself is then responsible for doing various preparation
based on the powerstate.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
According to the GPIO 'Wakeup and Interrupt' section of the TRM[1],
wake-up requests can only be generated on edge transitions.
Also for OMAP3, only edge GPIOs may lose interrupts when PER enters
RET/OFF state, this is addressed by gpio prepare|resume idle functions
[1] Section 25.5.3.1 OMAP34xx_ES3.1_TRM_V_Q
Signed-off-by: Chunqiu Wang <cqwang@motorola.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Off mode is now using the omap2 retention fix code for scanning GPIOs
during off-mode transitions. All the *non_wakeup_gpios variables
are now used for off-mode transition tracking on OMAP3. This patch fixes
cases where GPIO state changes are missed during off-mode.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Several ARM platforms/machines that use FIQ define their value of FIQ_START.
Since FIQ is not implemented for OMAP yet, this definition is missing from
OMAP header files.
Put an arbitrary value for FIQ_START into plat/irqs.h for OMAP. Even if not
used by the FIQ handler for Amstrad Delta, this is required for successfull
compilation of arch/arm/plat-omap/fiq.c that provides several
usefull functions.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We cannot use the omap34xx_sram_init(). It needs to be implemented
for omap4. Otherwise we get an error and the system won't boot:
Unhandled fault: imprecise external abort (0x1406) at 0xea963e94
...
Fix this by adding a dummy omap44xx_sram_init().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Zoom2 and 3 have UARTs only on the external debug board.
GPMC needs to be mapped early to use it for DEBUG_LL.
Additionally, 0xfb000000 overlaps with other areas, so
use 0xfa400000 for the virtual address instead.
Note that with the pending serial.c patches you need to
set console=ttyS0,115200n8 as it will be the only UART
mapped. To use DEBUG_LL, you need to pass also earlyprintk
in cmdline.
Cc: Allen Pais <allen.pais@ti.com>
Acked-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This removes the dependency to the UART1 being available for storing
the debug configuration in uncompress.h. This will simplify the
DEBUG_LL UART configuration for boards that may not have UART1, or
have an external UART as it requires only one mapping for DEBUG_LL.
The patch has a few limitations. Basically now we're assuming that
the kernel uncompress code won't overlap with OMAP_UART_INFO. We also
assume the printascii is called at least once before paging_init in
order for addruart to have a chance to read the UART setup from
OMAP_UART_INFO.
As suggested by Cyril Chemparathy <cyril@ti.com>,
Vikram Pandita <vikram.pandita@ti.com> and
Kevin Hilman <khilman@deeprootsystems.com>. Based on an earlier
patch posted for Davinci by Cyril Chemparathy <cyril@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we'll get an error about get_irqnr_and_base being defined
twice. Add an entry for omap4, and use ARCH_OMAP3 for omap3 instead of
ARCH_OMAP3430.
Also fix the check for omap1 to use ARCH_OMAP2PLUS to avoid having to
add ARCH_OMAP4 separately there.
Signed-off-by: Tony Lindgren <tony@atomide.com>
- registration with multi OMAP kernels support
- clocks
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
MUSB can supply upto 500mA such as, AM3517 and OMAP3EVM Rev >=E and thus
the 'power' field has to hold values above 255.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (39 commits)
omap: delete unused bootloader tag variables
omap: Devkit8000: Remove unused pins
omap: Devkit8000: Change position of init calls
omap: Devkit8000: Remove unnecessary include file
omap: Devkit8000: Fix typo in pin name
omap: Devkit8000: Add missing package selection
omap: Devkit8000: Fix typo in supplies
n8x0_defconfig: remove CONFIG_NILFS2_FS override
omap: board-sdp-flash.c: Fix typos in debug output
omap4: Fix McBSP4 base address
omap: rx51_defconfig: Remove CONFIG_SYSFS_DEPRECATED*=y options
omap: rx51_defconfig: Remove duplicate phonet
omap: fix a gpmc nand problem
AM3517: initialize i2c subsystem after mux subsystem
omap: remove one of the define of INT_34XX_BENCH_MPU_EMUL
omap: fix the compile error if CONFIG_MTD_NAND_OMAP2 is notenabled
OMAP4: Clocks: Change SPI Instance Names
omap: Devkit8000: Fix wrong usb port on Devkit8000
OMAP4: Fix for CONTROL register Base
OMAP4-HSMMC: FIX for MMC5 Controller IRQ Base
...
They are not needed and add over 512 bytes to kernel data.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
INT_34XX_BENCH_MPU_EMUL was defined twice, another is at Line 312.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If CONFIG_MTD_NAND_OMAP2 is not enabled, there will be a compile error,
"gpmc_nand_init() is not defined". Add a inline noop function to fix it.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the base address of CONTROL register on OMAP4430SDP.
The control base is used by peripherals like MMC1 for PBIAS configuration.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The register DMA4_CDAC needs to be initialized to zero
before starting DMA transfer.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Govindraj R <govindraj.raja@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Reported-by:S, Venkatraman <svenkatr@ti.com>
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since IRQ_TYPE_EDGE_BOTH is defined as (IRQ_TYPE_EDGE_FALLING |
IRQ_TYPE_EDGE_RISING), testing against it with a bitwise AND also matches
both single-edge cases in addition to the intended both edges case. Fix it,
replacing with a more accurate expression.
Created and tested againts linux-2.6.34-rc3.
Applicable to 2.6.33-stable as well.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When the 32k sync timer is used for sched_clock(), it should count
time from the kernel boot (clocksource init) instead of the last HW
reset. Otherwise printk.time values will jump suddenly during the boot:
[ 0.000000] calling omap2_clk_arch_init+0x0/0x138 @ 1
[ 0.000000] initcall omap2_clk_arch_init+0x0/0x138 returned -22 after 0 usecs
[ 0.000000] initcall omap2_clk_arch_init+0x0/0x138 returned with error code -22
[ 0.000000] calling omap_init_clocksource_32k+0x0/0x98 @ 1
[ 508.697937] initcall omap_init_clocksource_32k+0x0/0x98 returned 0 after 0 usecs
[ 508.697967] calling omap_init_devices+0x0/0x38 @ 1
[ 508.698425] initcall omap_init_devices+0x0/0x38 returned 0 after 0 usecs
This will confuse tools such as scripts/bootgraph.pl.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch corrects the width of sysc_flags in hwmod sysconfig structure
where the values to be stored to this variable exceed the current
field width.
Signed-off-by: Thara Gopinath <thara@ti.com>
[paul@pwsan.com: edited to apply; rearranged structure members to pack]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The MsBSP register cache will never have any error/status flags set, since
these flags are never written to the reg_cache. So it is kind of not
necessary to clear these flags, which are actually always 0.
In other words, clearing the status/error flags are not necessary, since the
reg_cache will never got these bits set. We can just write back the
register content from the cache as it is when clearing an error condition.
Tested on Amstrad Delta.
Reported-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
New functions for querying the FIFO caused delay on both
TX and RX path.
On TX path the return value shows the number of used
locations in the FIFO.
On RX papth it returns the number of locations to be filled
to reach the threshold value (DMA will be triggered to read
the data out from the FIFO).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently if omap2420 is defined but not omap2430, cpu_is_omap2430()
is still defined as a macro, instead of #define'd to zero. This
results in conditional cpu_is_omap2430() code still being compiled,
and leads to possible compile/link errors. In particular for hwmod
init.
To fix, add extra #ifdefs to CPU check macros to ensure that the
is_omap* macros are zero for each OMAP2 if they are not configured
into the kernel.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For omap4 case, this was wrongly writing GPIO_LEVELDETECTx
registers with OMAP24XX_ offset and OMAP4_ offset.
Bug introduced in commit:
commit 3f1686a9bf
Author: Tony Lindgren <tony@atomide.com>
Date: Mon Feb 15 09:27:25 2010 -0800
omap: Fix gpio.c for multi-omap for omap4
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
arch/arm/plat-omap/include/plat/blizzard.h:9:
ERROR: spaces prohibited around that ':' (ctx:WxW)
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
