This patch adds support to sdc2 sdhci controller, which is used on some
of the boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds pinctrl required for sdhci for external sd card
controller.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to blsp2_spi5 device, which is used in some of
the APQ8096 based boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to blsp1_spi0 which is used on some of APQ8096
based boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to blsp2_i2c0, which is used on some of the
APQ8096 based boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to blsp2_i2c0 pinctrl.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to blsp2_i2c1, which is used in one of the
apq8096 based boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to blsp2_i2c1 pinctrl nodes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds blsp1_i2c2 support, as this bus is used on some of the
apq8096 boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds bslp2_uart2 node in soc so that boards that use this
uart can enable it.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds 2pin and 4 pin uart pinctrl support for blsp2_uart1
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds msmgpio label for pin and gpio controller so that
it can referenced in dedicated pins file and other board level gpios.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Unit addresses should not have a leading '0x'. Remove them.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Duc Dang <dhdang@apm.com>
The convention in these files is to use lowercase for "0x" prefixes and for
the hex constants themselves, but a few changes didn't follow that
convention, which makes the file annoying to read.
Use lowercase consistently for the hex constants. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Duc Dang <dhdang@apm.com>
- Anup adds nodes for the AHCI and SATA3 PHY peripherals to the Northstar2 SoCs
- Dhanajay enables pinctrl for the Northstar2 SoCs
- Jon Mason enables all of the UART peripherals found in the NS2 SVK and
finally adds the CCI-400 and PMU nodes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=296G
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.8/devicetree-arm64' of http://github.com/Broadcom/stblinux into next/dt64
This pull request contains Device Tree changes for Broadcom ARM64-based SoCS:
- Anup adds nodes for the AHCI and SATA3 PHY peripherals to the Northstar2 SoCs
- Dhanajay enables pinctrl for the Northstar2 SoCs
- Jon Mason enables all of the UART peripherals found in the NS2 SVK and
finally adds the CCI-400 and PMU nodes
* tag 'arm-soc/for-4.8/devicetree-arm64' of http://github.com/Broadcom/stblinux:
arm64: dts: NS2: Add CCI-400 PMU support
arm64: dts: NS2: Add all of the UARTs
arm64: dts: Enable GPIO for Broadcom NS2 SoC
arm64: dts: enable pinctrl for Broadcom NS2 SoC
arm64: dts: Add SATA3 AHCI and SATA3 PHY DT nodes for NS2
dt-bindings: ata: add compatible string for iProc AHCI controller
Signed-off-by: Olof Johansson <olof@lixom.net>
As Documentation/arm64/booting.txt says, the cpu-release-addr
location should be reserved.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
At first, 256 byte of the head of DRAM space was reserved for some
reasons. However, as the progress of development, it turned out
unnecessary, and it was never used in the end. Move the CPU release
address to leave no space.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This node consists of various system-level configuration registers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Update reserved-memory in accordance with memory the detailed memory map
for 8916, so that we will be able to reference the firmware memory
regions.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the devicetree node for the SCM firmware.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Add the PMU so we can get proper perf event support on this SoC.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add device bindings for CPUs to suspend using PSCI as the enable-method.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Tested-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch enables bam dma node, dma is used for both tx and rx on spi
and on high speed serial.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the necessary properties to enable the SD-card on db410c boards.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add dtsi file to support lg1313 SoC which based on Cortex-A53.
Also add dts file to support lg1312 reference board which based
on lg1313 SoC.
Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Update DTSI file to add the reset controller node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add node for ethernet interface and pinctrl pins.
Enable on odroid-C2 and P20x boards.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add DT nodes for additional UARTs (UART B & C in EE domain) and add pins
for all EE domain UARTs.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Update DTS and DTSI files to enable the pin controller. We also now
support the blinking blue LED on the Odroid-C2.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the two new compatibles for the Amlogic Meson GXBB pin controllers.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add two new buses in the DTS: hiu and periphs buses.
In the Amlogic S905/GXBB SoC several devices (clock / eth / pin
controllers, etc...) are mapped under these two buses. Add them in the
DT before starting to add new devices.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add support to the Northstar 2 Device tree file for the ARM CCI-400 PMU.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add all of the UARTs present on NS2 and enable them in the SVK device
tree file. Also, do some magic to make sure that uart3 is discovered as
ttyS0 (as that is the console UART).
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This enables the GPIO support for Broadcom NS2 SoC
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We have one dual-port SATA3 AHCI controller present in
NS2 SoC.
This patch enables SATA3 AHCI controller and SATA3 PHY
for NS2 SoC in NS2 DT.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The Broadcom iProc SoCs have AHCI compliant SATA controller. This
patch adds common compatible string for AHCI SATA controller on
iProc SoCs.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Drop 0x from unit address of gic as this is the desired form for
a unit address.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Warning (unit_address_vs_reg): Node /regulator@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@4 has a unit name, but no reg property
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Olof Johansson
Srinivas Kandagatla
Duc Dang
Bjorn Helgaas
Masahiro Yamada
Bjorn Andersson
Andy Gross
Stephen Boyd
Lina Iyer
Georgi Djakov
Chanho Min
Neil Armstrong
Kevin Hilman
Carlo Caione
Jon Mason
Yendapally Reddy Dhananjaya Reddy
Anup Patel
Simon Horman
Geert Uytterhoeven