On AR934x this UART is usually not initialized by the bootloader
as it is only used as a secondary serial port while the primary
UART is a newly introduced NS16550-compatible.
In order to make use of the ar933x-uart on AR934x without RTS/CTS
hardware flow control, one needs to set the
UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this
UART is used as primary/console, the bootloader on AR934x typically
doesn't set those bits.
Setting them explicitely on AR933x should not do any harm, so just
set them unconditionally.
Tested-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20200207095335.GA179836@makrotopia.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- fix randconfig to generate a sane .config
- rename hostprogs-y / always to hostprogs / always-y, which are
more natual syntax.
- optimize scripts/kallsyms
- fix yes2modconfig and mod2yesconfig
- make multiple directory targets ('make foo/ bar/') work
-----BEGIN PGP SIGNATURE-----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=sv4U
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- fix randconfig to generate a sane .config
- rename hostprogs-y / always to hostprogs / always-y, which are more
natual syntax.
- optimize scripts/kallsyms
- fix yes2modconfig and mod2yesconfig
- make multiple directory targets ('make foo/ bar/') work
* tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: make multiple directory targets work
kconfig: Invalidate all symbols after changing to y or m.
kallsyms: fix type of kallsyms_token_table[]
scripts/kallsyms: change table to store (strcut sym_entry *)
scripts/kallsyms: rename local variables in read_symbol()
kbuild: rename hostprogs-y/always to hostprogs/always-y
kbuild: fix the document to use extra-y for vmlinux.lds
kconfig: fix broken dependency in randconfig-generated .config
Zonefs is a very simple file system exposing each zone of a zoned block
device as a file.
Unlike a regular file system with native zoned block device support
(e.g. f2fs or the on-going btrfs effort), zonefs does not hide the
sequential write constraint of zoned block devices to the user. As a
result, zonefs is not a POSIX compliant file system. Its goal is to
simplify the implementation of zoned block devices support in
applications by replacing raw block device file accesses with a richer
file based API, avoiding relying on direct block device file ioctls
which may be more obscure to developers.
One example of this approach is the implementation of LSM
(log-structured merge) tree structures (such as used in RocksDB and
LevelDB) on zoned block devices by allowing SSTables to be stored in a
zone file similarly to a regular file system rather than as a range of
sectors of a zoned device. The introduction of the higher level
construct "one file is one zone" can help reducing the amount of changes
needed in the application while at the same time allowing the use of
zoned block devices with various programming languages other than C.
Zonefs IO management implementation uses the new iomap generic code.
Zonefs has been successfully tested using a functional test suite
(available with zonefs userland format tool on github) and a prototype
implementation of LevelDB on top of zonefs.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSRPv8tYSvhwAzJdzjdoc3SxdoYdgUCXj1y8QAKCRDdoc3SxdoY
dqozAP9J3t+Q95BgKgI5jP+XEtyYsPBTaVrvaSaViEnwtJLVoQD/ZQ1lTCZSE9OI
UkvWawkuFtLGfOxTqyA3eZrZi22Ttwk=
=YVvO
-----END PGP SIGNATURE-----
Merge tag 'zonefs-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs
Pull new zonefs file system from Damien Le Moal:
"Zonefs is a very simple file system exposing each zone of a zoned
block device as a file.
Unlike a regular file system with native zoned block device support
(e.g. f2fs or the on-going btrfs effort), zonefs does not hide the
sequential write constraint of zoned block devices to the user. As a
result, zonefs is not a POSIX compliant file system. Its goal is to
simplify the implementation of zoned block devices support in
applications by replacing raw block device file accesses with a richer
file based API, avoiding relying on direct block device file ioctls
which may be more obscure to developers.
One example of this approach is the implementation of LSM
(log-structured merge) tree structures (such as used in RocksDB and
LevelDB) on zoned block devices by allowing SSTables to be stored in a
zone file similarly to a regular file system rather than as a range of
sectors of a zoned device. The introduction of the higher level
construct "one file is one zone" can help reducing the amount of
changes needed in the application while at the same time allowing the
use of zoned block devices with various programming languages other
than C.
Zonefs IO management implementation uses the new iomap generic code.
Zonefs has been successfully tested using a functional test suite
(available with zonefs userland format tool on github) and a prototype
implementation of LevelDB on top of zonefs"
* tag 'zonefs-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
zonefs: Add documentation
fs: New zonefs file system
In order to allow the GICv4 code to link properly on 32bit ARM,
make sure we don't use 64bit divisions when it isn't strictly
necessary.
Fixes: 4e6437f12d ("irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=F1qf
-----END PGP SIGNATURE-----
Merge tag '5.6-rc-smb3-plugfest-patches' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"13 cifs/smb3 patches, most from testing at the SMB3 plugfest this week:
- Important fix for multichannel and for modefromsid mounts.
- Two reconnect fixes
- Addition of SMB3 change notify support
- Backup tools fix
- A few additional minor debug improvements (tracepoints and
additional logging found useful during testing this week)"
* tag '5.6-rc-smb3-plugfest-patches' of git://git.samba.org/sfrench/cifs-2.6:
smb3: Add defines for new information level, FileIdInformation
smb3: print warning once if posix context returned on open
smb3: add one more dynamic tracepoint missing from strict fsync path
cifs: fix mode bits from dir listing when mounted with modefromsid
cifs: fix channel signing
cifs: add SMB3 change notification support
cifs: make multichannel warning more visible
cifs: fix soft mounts hanging in the reconnect code
cifs: Add tracepoints for errors on flush or fsync
cifs: log warning message (once) if out of disk space
cifs: fail i/o on soft mounts if sessionsetup errors out
smb3: fix problem with null cifs super block with previous patch
SMB3: Backup intent flag missing from some more ops
Pull vboxfs from Al Viro:
"This is the VirtualBox guest shared folder support by Hans de Goede,
with fixups for fs_parse folded in to avoid bisection hazards from
those API changes..."
* 'work.vboxsf' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Add VirtualBox guest shared folder (vboxsf) support
- Ensure that the PIT is set up when the local APIC is disable or
configured in legacy mode. This is caused by an ordering issue
introduced in the recent changes which skip PIT initialization when the
TSC and APIC frequencies are already known.
- Handle malformed SRAT tables during early ACPI parsing which caused an
infinite loop anda boot hang.
- Fix a long standing race in the affinity setting code which affects PCI
devices with non-maskable MSI interrupts. The problem is caused by the
non-atomic writes of the MSI address (destination APIC id) and data
(vector) fields which the device uses to construct the MSI message. The
non-atomic writes are mandated by PCI.
If both fields change and the device raises an interrupt after writing
address and before writing data, then the MSI block constructs a
inconsistent message which causes interrupts to be lost and subsequent
malfunction of the device.
The fix is to redirect the interrupt to the new vector on the current
CPU first and then switch it over to the new target CPU. This allows to
observe an eventually raised interrupt in the transitional stage (old
CPU, new vector) to be observed in the APIC IRR and retriggered on the
new target CPU and the new vector. The potential spurious interrupts
caused by this are harmless and can in the worst case expose a buggy
driver (all handlers have to be able to deal with spurious interrupts as
they can and do happen for various reasons).
- Add the missing suspend/resume mechanism for the HYPERV hypercall page
which prevents resume hibernation on HYPERV guests. This change got
lost before the merge window.
- Mask the IOAPIC before disabling the local APIC to prevent potentially
stale IOAPIC remote IRR bits which cause stale interrupt lines after
resume.
-----BEGIN PGP SIGNATURE-----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=WxKD
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for X86:
- Ensure that the PIT is set up when the local APIC is disable or
configured in legacy mode. This is caused by an ordering issue
introduced in the recent changes which skip PIT initialization when
the TSC and APIC frequencies are already known.
- Handle malformed SRAT tables during early ACPI parsing which caused
an infinite loop anda boot hang.
- Fix a long standing race in the affinity setting code which affects
PCI devices with non-maskable MSI interrupts. The problem is caused
by the non-atomic writes of the MSI address (destination APIC id)
and data (vector) fields which the device uses to construct the MSI
message. The non-atomic writes are mandated by PCI.
If both fields change and the device raises an interrupt after
writing address and before writing data, then the MSI block
constructs a inconsistent message which causes interrupts to be
lost and subsequent malfunction of the device.
The fix is to redirect the interrupt to the new vector on the
current CPU first and then switch it over to the new target CPU.
This allows to observe an eventually raised interrupt in the
transitional stage (old CPU, new vector) to be observed in the APIC
IRR and retriggered on the new target CPU and the new vector.
The potential spurious interrupts caused by this are harmless and
can in the worst case expose a buggy driver (all handlers have to
be able to deal with spurious interrupts as they can and do happen
for various reasons).
- Add the missing suspend/resume mechanism for the HYPERV hypercall
page which prevents resume hibernation on HYPERV guests. This
change got lost before the merge window.
- Mask the IOAPIC before disabling the local APIC to prevent
potentially stale IOAPIC remote IRR bits which cause stale
interrupt lines after resume"
* tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Mask IOAPIC entries when disabling the local APIC
x86/hyperv: Suspend/resume the hypercall page for hibernation
x86/apic/msi: Plug non-maskable MSI affinity race
x86/boot: Handle malformed SRAT tables during early ACPI parsing
x86/timer: Don't skip PIT setup when APIC is disabled or in legacy mode
- Make the UP version of smp_call_function_single() match SMP semantics
when called for a not available CPU. Instead of emitting a warning and
assuming that the function call target is CPU0, return a proper error
code like the SMP version does.
- Remove a superfluous check in smp_call_function_many_cond()
-----BEGIN PGP SIGNATURE-----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=XfHp
-----END PGP SIGNATURE-----
Merge tag 'smp-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull SMP fixes from Thomas Gleixner:
"Two fixes for the SMP related functionality:
- Make the UP version of smp_call_function_single() match SMP
semantics when called for a not available CPU. Instead of emitting
a warning and assuming that the function call target is CPU0,
return a proper error code like the SMP version does.
- Remove a superfluous check in smp_call_function_many_cond()"
* tag 'smp-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
smp/up: Make smp_call_function_single() match SMP semantics
smp: Remove superfluous cond_func check in smp_call_function_many_cond()
- Kernel fixes:
- Install cgroup events to the correct CPU context to prevent a
potential list double add
- Prevent am intgeer underflow in the perf mlock acounting
- Add a missing prototyp for arch_perf_update_userpage()
- Tooling:
- Add a missing unlock in the error path of maps__insert() in perf maps.
- Fix the build with the latest libbfd
- Fix the perf parser so it does not delete parse event terms, which
caused a regression for using perf with the ARM CoreSight as the sink
confuguration was missing due to the deletion.
- Fix the double free in the perf CPU map merging test case
- Add the missing ustring support for the perf probe command
-----BEGIN PGP SIGNATURE-----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=xu7D
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"A set of fixes and improvements for the perf subsystem:
Kernel fixes:
- Install cgroup events to the correct CPU context to prevent a
potential list double add
- Prevent an integer underflow in the perf mlock accounting
- Add a missing prototype for arch_perf_update_userpage()
Tooling:
- Add a missing unlock in the error path of maps__insert() in perf
maps.
- Fix the build with the latest libbfd
- Fix the perf parser so it does not delete parse event terms, which
caused a regression for using perf with the ARM CoreSight as the
sink configuration was missing due to the deletion.
- Fix the double free in the perf CPU map merging test case
- Add the missing ustring support for the perf probe command"
* tag 'perf-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf maps: Add missing unlock to maps__insert() error case
perf probe: Add ustring support for perf probe command
perf: Make perf able to build with latest libbfd
perf test: Fix test case Merge cpu map
perf parse: Copy string to perf_evsel_config_term
perf parse: Refactor 'struct perf_evsel_config_term'
kernel/events: Add a missing prototype for arch_perf_update_userpage()
perf/cgroups: Install cgroup events to correct cpuctx
perf/core: Fix mlock accounting in perf_mmap()
- Handle a subtle race between the clocksource watchdog and a concurrent
clocksource watchdog stop/start sequence correctly to prevent a timer
double add bug.
- Fix the file path for the core time namespace file.
-----BEGIN PGP SIGNATURE-----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=0zFj
-----END PGP SIGNATURE-----
Merge tag 'timers-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Two small fixes for the time(r) subsystem:
- Handle a subtle race between the clocksource watchdog and a
concurrent clocksource watchdog stop/start sequence correctly to
prevent a timer double add bug.
- Fix the file path for the core time namespace file"
* tag 'timers-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Prevent double add_timer_on() for watchdog_timer
MAINTAINERS: Correct path to time namespace source file
- Provision only ACPI enabled redistributors on GICv3
- Use the proper command colums when building the INVALL command for the
GICv3-ITS
- Ensure the allocation of the L2 vPE table for GICv4.1
- Correct the GICv4.1 VPROBASER programming so it uses the proper size
- A set of small GICv4.1 tidy up patches
- Configuration cleanup for C-SKY interrupt chip
- Clarify the function documentation for irq_set_wake() to document that
the wakeup functionality is orthogonal to the irq disable/enable
mechanism.
-----BEGIN PGP SIGNATURE-----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=a9t/
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull interrupt fixes from Thomas Gleixner:
"A set of fixes for the interrupt subsystem:
- Provision only ACPI enabled redistributors on GICv3
- Use the proper command colums when building the INVALL command for
the GICv3-ITS
- Ensure the allocation of the L2 vPE table for GICv4.1
- Correct the GICv4.1 VPROBASER programming so it uses the proper
size
- A set of small GICv4.1 tidy up patches
- Configuration cleanup for C-SKY interrupt chip
- Clarify the function documentation for irq_set_wake() to document
that the wakeup functionality is orthogonal to the irq
disable/enable mechanism"
* tag 'irq-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Rename VPENDBASER/VPROPBASER accessors
irqchip/gic-v3-its: Remove superfluous WARN_ON
irqchip/gic-v4.1: Drop 'tmp' in inherit_vpe_l1_table_from_rd()
irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level
irqchip/gic-v4.1: Set vpe_l1_base for all redistributors
irqchip/gic-v4.1: Fix programming of GICR_VPROPBASER_4_1_SIZE
genirq: Clarify that irq wake state is orthogonal to enable/disable
irqchip/gic-v3-its: Reference to its_invall_cmd descriptor when building INVALL
irqchip: Some Kconfig cleanup for C-SKY
irqchip/gic-v3: Only provision redistributors that are enabled in ACPI
recent rework of the EFI memory map parsing. On systems with invalid memmap
entries the cleanup function uses an value which cannot be relied on in
this stage. Use the actual EFI memmap entry instead.
-----BEGIN PGP SIGNATURE-----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=AU47
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fix from Thomas Gleixner:
"A single fix for a EFI boot regression on X86 which was caused by the
recent rework of the EFI memory map parsing. On systems with invalid
memmap entries the cleanup function uses an value which cannot be
relied on in this stage. Use the actual EFI memmap entry instead"
* tag 'efi-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/x86: Fix boot regression on systems with invalid memmap entries
Five small patches, all in drivers or doc, which missed the initial
pull request. The qla2xxx and megaraid_sas are actual fixes and the
rest are spelling and doc changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXj8MoCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishUjlAQChB8+I
pBKVOfU+38vndu+YW6IRb11HhxKzY9LlHVf04wD+LxKsxuYKpZjivytfuYJGsxMD
C5EWLUxB7GYUQItEBjQ=
=7xJj
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull misc SCSI fixes from James Bottomley:
"Five small patches, all in drivers or doc, which missed the initial
pull request.
The qla2xxx and megaraid_sas are actual fixes and the rest are
spelling and doc changes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: fix spelling mistake "initilized" -> "initialized"
scsi: pm80xx: fix spelling mistake "to" -> "too"
scsi: MAINTAINERS: ufs: remove pedrom.sousa@synopsys.com
scsi: megaraid_sas: fixup MSIx interrupt setup during resume
scsi: qla2xxx: Fix unbound NVME response length
Pull networking fixes from David Miller:
1) Unbalanced locking in mwifiex_process_country_ie, from Brian Norris.
2) Fix thermal zone registration in iwlwifi, from Andrei
Otcheretianski.
3) Fix double free_irq in sgi ioc3 eth, from Thomas Bogendoerfer.
4) Use after free in mptcp, from Florian Westphal.
5) Use after free in wireguard's root_remove_peer_lists, from Eric
Dumazet.
6) Properly access packets heads in bonding alb code, from Eric
Dumazet.
7) Fix data race in skb_queue_len(), from Qian Cai.
8) Fix regression in r8169 on some chips, from Heiner Kallweit.
9) Fix XDP program ref counting in hv_netvsc, from Haiyang Zhang.
10) Certain kinds of set link netlink operations can cause a NULL deref
in the ipv6 addrconf code. Fix from Eric Dumazet.
11) Don't cancel uninitialized work queue in drop monitor, from Ido
Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
net: thunderx: use proper interface type for RGMII
mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap
bpf: Improve bucket_log calculation logic
selftests/bpf: Test freeing sockmap/sockhash with a socket in it
bpf, sockhash: Synchronize_rcu before free'ing map
bpf, sockmap: Don't sleep while holding RCU lock on tear-down
bpftool: Don't crash on missing xlated program instructions
bpf, sockmap: Check update requirements after locking
drop_monitor: Do not cancel uninitialized work item
mlxsw: spectrum_dpipe: Add missing error path
mlxsw: core: Add validation of hardware device types for MGPIR register
mlxsw: spectrum_router: Clear offload indication from IPv6 nexthops on abort
selftests: mlxsw: Add test cases for local table route replacement
mlxsw: spectrum_router: Prevent incorrect replacement of local table routes
net: dsa: microchip: enable module autoprobe
ipv6/addrconf: fix potential NULL deref in inet6_set_link_af()
dpaa_eth: support all modes with rate adapting PHYs
net: stmmac: update pci platform data to use phy_interface
net: stmmac: xgmac: fix missing IFF_MULTICAST checki in dwxgmac2_set_filter
net: stmmac: fix missing IFF_MULTICAST check in dwmac4_set_filter
...
VirtualBox hosts can share folders with guests, this commit adds a
VFS driver implementing the Linux-guest side of this, allowing folders
exported by the host to be mounted under Linux.
This driver depends on the guest <-> host IPC functions exported by
the vboxguest driver.
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fix an existing bug in our user access handling, exposed by one of the bug fixes
we merged this cycle.
A fix for a boot hang on 32-bit with CONFIG_TRACE_IRQFLAGS and the recently
added CONFIG_VMAP_STACK.
Thanks to:
Christophe Leroy, Guenter Roeck.
-----BEGIN PGP SIGNATURE-----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=+Urh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix an existing bug in our user access handling, exposed by one of
the bug fixes we merged this cycle.
- A fix for a boot hang on 32-bit with CONFIG_TRACE_IRQFLAGS and the
recently added CONFIG_VMAP_STACK.
Thanks to: Christophe Leroy, Guenter Roeck.
* tag 'powerpc-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Fix CONFIG_TRACE_IRQFLAGS with CONFIG_VMAP_STACK
powerpc/futex: Fix incorrect user access blocking
This is a merge error on my part - the driver was merged into mainline
by commit c5951e7c8e ("Merge tag 'mips_5.6' of git://../mips/linux")
over a week ago, but nobody apparently noticed that it didn't actually
build due to still having a reference to the devm_ioremap_nocache()
function, removed a few days earlier through commit 6a1000bd27 ("Merge
tag 'ioremap-5.6' of git://../ioremap").
Apparently this didn't get any build testing anywhere. Not perhaps all
that surprising: it's restricted to 64-bit MIPS only, and only with the
new SGI_MFD_IOC3 support enabled.
I only noticed because the ioremap conflicts in the ARM SoC driver
update made me check there weren't any others hiding, and I found this
one.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is some material that we picked up into our tree late, or that had
more complex dependencies on more than one topic branch that makes sense
to keep separately.
- TI support for secure accelerators and hwrng on OMAP4/5
- TI camera changes for dra7 and am437x and SGX improvement due to better
reset control support on am335x, am437x and dra7
- Davinci moves to proper clocksource on DM365, and regulator/audio
improvements for DM365 and DM644x eval boards
-----BEGIN PGP SIGNATURE-----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=R7GU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC late updates from Olof Johansson:
"This is some material that we picked up into our tree late, or that
had more complex dependencies on more than one topic branch that makes
sense to keep separately.
- TI support for secure accelerators and hwrng on OMAP4/5
- TI camera changes for dra7 and am437x and SGX improvement due to
better reset control support on am335x, am437x and dra7
- Davinci moves to proper clocksource on DM365, and regulator/audio
improvements for DM365 and DM644x eval boards"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
ARM: dts: Configure interconnect target module for am437x sgx
ARM: dts: Configure sgx for dra7
ARM: dts: Configure rstctrl reset for am335x SGX
ARM: dts: dra7: Add ti-sysc node for VPE
ARM: dts: dra7: add vpe clkctrl node
ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
ARM: dts: am43xx: add support for clkout1 clock
arm: dts: dra76-evm: Add CAL and OV5640 nodes
arm: dtsi: dra76x: Add CAL dtsi node
arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
ARM: dts: DRA72: Add CAL dtsi node
ARM: dts: dra7-l4: Add ti-sysc node for CAM
ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
ARM: dts: dra7: add cam clkctrl node
ARM: OMAP2+: Drop legacy platform data for omap4 des
ARM: OMAP2+: Drop legacy platform data for omap4 sham
ARM: OMAP2+: Drop legacy platform data for omap4 aes
...
We keep this in a separate branch to avoid cross-branch conflicts, but
most of the material here is fairly boring -- some new drivers turned on
for hardware since they were merged, and some refreshed files due to
time having moved a lot of entries around.
-----BEGIN PGP SIGNATURE-----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=8F5r
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC defconfig updates from Olof Johansson:
"We keep this in a separate branch to avoid cross-branch conflicts, but
most of the material here is fairly boring -- some new drivers turned
on for hardware since they were merged, and some refreshed files due
to time having moved a lot of entries around"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
ARM: configs: at91: enable MMC_SDHCI_OF_AT91 and MICROCHIP_PIT64B
arm64: defconfig: Enable Broadcom's GENET Ethernet controller
ARM: multi_v7_defconfig: Enable devfreq thermal integration
ARM: exynos_defconfig: Enable devfreq thermal integration
ARM: multi_v7_defconfig: Enable NFS v4.1 and v4.2
ARM: exynos_defconfig: Enable NFS v4.1 and v4.2
arm64: defconfig: Enable Actions Semi specific drivers
arm64: defconfig: Enable Broadcom's STB PCIe controller
arm64: defconfig: Enable CONFIG_CLK_IMX8MP by default
ARM: configs: at91: enable config flags for sam9x60 SoC
ARM: configs: at91: use savedefconfig
arm64: defconfig: Enable tegra XUDC support
ARM: defconfig: gemini: Update defconfig
arm64: defconfig: enable CONFIG_ARM_QCOM_CPUFREQ_NVMEM
arm64: defconfig: enable CONFIG_QCOM_CPR
arm64: defconfig: Enable HFPLL
arm64: defconfig: Enable CRYPTO_DEV_FSL_CAAM
ARM: imx_v6_v7_defconfig: Select the TFP410 driver
ARM: imx_v6_v7_defconfig: Enable NFS_V4_1 and NFS_V4_2 support
arm64: defconfig: Enable ATH10K_SNOC
...
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----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=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
Most of these are smaller fixes that have accrued, and some continued
cleanup of OMAP platforms towards shared frameworks.
One new SoC from Atmel/Microchip: sam9x60.
-----BEGIN PGP SIGNATURE-----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=fIjZ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"Most of these are smaller fixes that have accrued, and some continued
cleanup of OMAP platforms towards shared frameworks.
One new SoC from Atmel/Microchip: sam9x60"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (35 commits)
ARM: OMAP2+: Fix undefined reference to omap_secure_init
ARM: s3c64xx: Drop unneeded select of TIMER_OF
ARM: exynos: Drop unneeded select of MIGHT_HAVE_CACHE_L2X0
ARM: s3c24xx: Switch to atomic pwm API in rx1950
ARM: OMAP2+: sleep43xx: Call secure suspend/resume handlers
ARM: OMAP2+: Use ARM SMC Calling Convention when OP-TEE is available
ARM: OMAP2+: Introduce check for OP-TEE in omap_secure_init()
ARM: OMAP2+: Add omap_secure_init callback hook for secure initialization
ARM: at91: Documentation: add sam9x60 product and datasheet
ARM: at91: pm: use of_device_id array to find the proper shdwc node
ARM: at91: pm: use SAM9X60 PMC's compatible
ARM: imx: only select ARM_ERRATA_814220 for ARMv7-A
ARM: zynq: use physical cpuid in zynq_slcr_cpu_stop/start
ARM: tegra: Use clk_m CPU on Tegra124 LP1 resume
ARM: tegra: Modify reshift divider during LP1
ARM: tegra: Enable PLLP bypass during Tegra124 LP1
ARM: samsung: Rename Samsung and Exynos to lowercase
ARM: exynos: Correct the help text for platform Kconfig option
ARM: bcm: Select ARM_AMBA for ARCH_BRCMSTB
ARM: brcmstb: Add debug UART entry for 7216
...
One patch in the compat-ioctl series broke 32-bit rootfs for multiple
people testing on 64-bit kernels. Let's fix it in -rc1 before others
run into the same issue.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=uMS2
-----END PGP SIGNATURE-----
Merge tag 'compat-ioctl-fix' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground
Pull compat-ioctl fix from Arnd Bergmann:
"One patch in the compat-ioctl series broke 32-bit rootfs for multiple
people testing on 64-bit kernels. Let's fix it in -rc1 before others
run into the same issue"
* tag 'compat-ioctl-fix' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground:
compat_ioctl: fix FIONREAD on devices
Pull vfs file system parameter updates from Al Viro:
"Saner fs_parser.c guts and data structures. The system-wide registry
of syntax types (string/enum/int32/oct32/.../etc.) is gone and so is
the horror switch() in fs_parse() that would have to grow another case
every time something got added to that system-wide registry.
New syntax types can be added by filesystems easily now, and their
namespace is that of functions - not of system-wide enum members. IOW,
they can be shared or kept private and if some turn out to be widely
useful, we can make them common library helpers, etc., without having
to do anything whatsoever to fs_parse() itself.
And we already get that kind of requests - the thing that finally
pushed me into doing that was "oh, and let's add one for timeouts -
things like 15s or 2h". If some filesystem really wants that, let them
do it. Without somebody having to play gatekeeper for the variants
blessed by direct support in fs_parse(), TYVM.
Quite a bit of boilerplate is gone. And IMO the data structures make a
lot more sense now. -200LoC, while we are at it"
* 'merge.nfs-fs_parse.1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (25 commits)
tmpfs: switch to use of invalfc()
cgroup1: switch to use of errorfc() et.al.
procfs: switch to use of invalfc()
hugetlbfs: switch to use of invalfc()
cramfs: switch to use of errofc() et.al.
gfs2: switch to use of errorfc() et.al.
fuse: switch to use errorfc() et.al.
ceph: use errorfc() and friends instead of spelling the prefix out
prefix-handling analogues of errorf() and friends
turn fs_param_is_... into functions
fs_parse: handle optional arguments sanely
fs_parse: fold fs_parameter_desc/fs_parameter_spec
fs_parser: remove fs_parameter_description name field
add prefix to fs_context->log
ceph_parse_param(), ceph_parse_mon_ips(): switch to passing fc_log
new primitive: __fs_parse()
switch rbd and libceph to p_log-based primitives
struct p_log, variants of warnf() et.al. taking that one instead
teach logfc() to handle prefices, give it saner calling conventions
get rid of cg_invalf()
...
Pull misc vfs updates from Al Viro:
- bmap series from cmaiolino
- getting rid of convolutions in copy_mount_options() (use a couple of
copy_from_user() instead of the __get_user() crap)
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
saner copy_mount_options()
fibmap: Reject negative block numbers
fibmap: Use bmap instead of ->bmap method in ioctl_fibmap
ecryptfs: drop direct calls to ->bmap
cachefiles: drop direct usage of ->bmap method.
fs: Enable bmap() function to properly return errors
Merge thundering herd avoidance on pipe IO.
This would have been applied for 5.5 already, but got delayed because of
a user-space race condition in the GNU make jobserver code. Now that
there's a new GNU make 4.3 release, and most distributions seem to have
at least applied the (almost three year old) fix for the problem, let's
see if people notice.
And it might have been just bad random timing luck on my machine.
If you do hit the race condition, things will still work, but the
symptom is that you don't get nearly the expected parallelism when using
"make -j<N>".
The jobserver bug can definitely happen without this patch too, but
seems to be easier to trigger when we no longer wake up pipe waiters
unnecessarily.
* pipe-exclusive-wakeup:
pipe: use exclusive waits when reading or writing
This makes the pipe code use separate wait-queues and exclusive waiting
for readers and writers, avoiding a nasty thundering herd problem when
there are lots of readers waiting for data on a pipe (or, less commonly,
lots of writers waiting for a pipe to have space).
While this isn't a common occurrence in the traditional "use a pipe as a
data transport" case, where you typically only have a single reader and
a single writer process, there is one common special case: using a pipe
as a source of "locking tokens" rather than for data communication.
In particular, the GNU make jobserver code ends up using a pipe as a way
to limit parallelism, where each job consumes a token by reading a byte
from the jobserver pipe, and releases the token by writing a byte back
to the pipe.
This pattern is fairly traditional on Unix, and works very well, but
will waste a lot of time waking up a lot of processes when only a single
reader needs to be woken up when a writer releases a new token.
A simplified test-case of just this pipe interaction is to create 64
processes, and then pass a single token around between them (this
test-case also intentionally passes another token that gets ignored to
test the "wake up next" logic too, in case anybody wonders about it):
#include <unistd.h>
int main(int argc, char **argv)
{
int fd[2], counters[2];
pipe(fd);
counters[0] = 0;
counters[1] = -1;
write(fd[1], counters, sizeof(counters));
/* 64 processes */
fork(); fork(); fork(); fork(); fork(); fork();
do {
int i;
read(fd[0], &i, sizeof(i));
if (i < 0)
continue;
counters[0] = i+1;
write(fd[1], counters, (1+(i & 1)) *sizeof(int));
} while (counters[0] < 1000000);
return 0;
}
and in a perfect world, passing that token around should only cause one
context switch per transfer, when the writer of a token causes a
directed wakeup of just a single reader.
But with the "writer wakes all readers" model we traditionally had, on
my test box the above case causes more than an order of magnitude more
scheduling: instead of the expected ~1M context switches, "perf stat"
shows
231,852.37 msec task-clock # 15.857 CPUs utilized
11,250,961 context-switches # 0.049 M/sec
616,304 cpu-migrations # 0.003 M/sec
1,648 page-faults # 0.007 K/sec
1,097,903,998,514 cycles # 4.735 GHz
120,781,778,352 instructions # 0.11 insn per cycle
27,997,056,043 branches # 120.754 M/sec
283,581,233 branch-misses # 1.01% of all branches
14.621273891 seconds time elapsed
0.018243000 seconds user
3.611468000 seconds sys
before this commit.
After this commit, I get
5,229.55 msec task-clock # 3.072 CPUs utilized
1,212,233 context-switches # 0.232 M/sec
103,951 cpu-migrations # 0.020 M/sec
1,328 page-faults # 0.254 K/sec
21,307,456,166 cycles # 4.074 GHz
12,947,819,999 instructions # 0.61 insn per cycle
2,881,985,678 branches # 551.096 M/sec
64,267,015 branch-misses # 2.23% of all branches
1.702148350 seconds time elapsed
0.004868000 seconds user
0.110786000 seconds sys
instead. Much better.
[ Note! This kernel improvement seems to be very good at triggering a
race condition in the make jobserver (in GNU make 4.2.1) for me. It's
a long known bug that was fixed back in June 2017 by GNU make commit
b552b0525198 ("[SV 51159] Use a non-blocking read with pselect to
avoid hangs.").
But there wasn't a new release of GNU make until 4.3 on Jan 19 2020,
so a number of distributions may still have the buggy version. Some
have backported the fix to their 4.2.1 release, though, and even
without the fix it's quite timing-dependent whether the bug actually
is hit. ]
Josh Triplett says:
"I've been hammering on your pipe fix patch (switching to exclusive
wait queues) for a month or so, on several different systems, and I've
run into no issues with it. The patch *substantially* improves
parallel build times on large (~100 CPU) systems, both with parallel
make and with other things that use make's pipe-based jobserver.
All current distributions (including stable and long-term stable
distributions) have versions of GNU make that no longer have the
jobserver bug"
Tested-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
My final cleanup patch for sys_compat_ioctl() introduced a regression on
the FIONREAD ioctl command, which is used for both regular and special
files, but only works on regular files after my patch, as I had missed
the warning that Al Viro put into a comment right above it.
Change it back so it can work on any file again by moving the implementation
to do_vfs_ioctl() instead.
Fixes: 77b9040195 ("compat_ioctl: simplify the implementation")
Reported-and-tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Reported-and-tested-by: youling257 <youling257@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The configuration of the OCTEONTX XCV_DLL_CTL register via
xcv_init_hw() is such that the RGMII RX delay is bypassed
leaving the RGMII TX delay enabled in the MAC:
/* Configure DLL - enable or bypass
* TX no bypass, RX bypass
*/
cfg = readq_relaxed(xcv->reg_base + XCV_DLL_CTL);
cfg &= ~0xFF03;
cfg |= CLKRX_BYP;
writeq_relaxed(cfg, xcv->reg_base + XCV_DLL_CTL);
This would coorespond to a interface type of PHY_INTERFACE_MODE_RGMII_RXID
and not PHY_INTERFACE_MODE_RGMII.
Fixing this allows RGMII PHY drivers to do the right thing (enable
RX delay in the PHY) instead of erroneously enabling both delays in the
PHY.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of fixes for v5.6. Buffer overflow fixes to mwifiex, quite a
few functionality fixes to iwlwifi and smaller fixes to other drivers.
mwifiex
* fix an unlock from a previous security fix
* fix two buffer overflows
libertas
* fix two bugs from previous security fixes
iwlwifi
* fix module removal with multiple NICs
* don't treat IGTK removal failure as an error
* avoid FW crashes due to DTS measurement races
* fix a potential use after free in FTM code
* prevent a NULL pointer dereference in iwl_mvm_cfg_he_sta()
* fix TDLS discovery
* check all CPUs when trying to detect an error during resume
rtw88
* fix clang warning
mt76
* fix reading of max_nss value from a register
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJePoxJAAoJEG4XJFUm622b7a4H/2t/K/AmDv+j2mGos+2oVlSh
RFIXBjYs4GY5NGdLQx56qfiQzlgn8NAWwQqwhtoyVxnJTZjhmQkfMpJIw14tbFB1
OwHd+q7y7jXY9v7YBPlyqCxkzQL3u+GrzFIb04cXrSdzqh+5qWk4Zn7F6ZYJ1vwb
xRDOJfOE/a9GGzzY5+iwxyZ6Y1E+OjbgT4Ps5YUaotH1iMGza7NPu6s+UkULkyRo
ylbiOR9u6jOiwUkSxUz+GGiXKJ9BQTLKm5kLM7lO5I49AcZb5UOIKJaJxHN0hMwj
uprqUsqtbO+bv8SKAjKLR/yQf2gmB+pSSeAmmfJ8ov5igg2g12sNfdy8ScWLks8=
=FiiT
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-02-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.6
First set of fixes for v5.6. Buffer overflow fixes to mwifiex, quite a
few functionality fixes to iwlwifi and smaller fixes to other drivers.
mwifiex
* fix an unlock from a previous security fix
* fix two buffer overflows
libertas
* fix two bugs from previous security fixes
iwlwifi
* fix module removal with multiple NICs
* don't treat IGTK removal failure as an error
* avoid FW crashes due to DTS measurement races
* fix a potential use after free in FTM code
* prevent a NULL pointer dereference in iwl_mvm_cfg_he_sta()
* fix TDLS discovery
* check all CPUs when trying to detect an error during resume
rtw88
* fix clang warning
mt76
* fix reading of max_nss value from a register
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2020-02-07
The following pull-request contains BPF updates for your *net* tree.
We've added 15 non-merge commits during the last 10 day(s) which contain
a total of 12 files changed, 114 insertions(+), 31 deletions(-).
The main changes are:
1) Various BPF sockmap fixes related to RCU handling in the map's tear-
down code, from Jakub Sitnicki.
2) Fix macro state explosion in BPF sk_storage map when calculating its
bucket_log on allocation, from Martin KaFai Lau.
3) Fix potential BPF sockmap update race by rechecking socket's established
state under lock, from Lorenz Bauer.
4) Fix crash in bpftool on missing xlated instructions when kptr_restrict
sysctl is set, from Toke Høiland-Jørgensen.
5) Fix i40e's XSK wakeup code to return proper error in busy state and
various misc fixes in xdpsock BPF sample code, from Maciej Fijalkowski.
6) Fix the way modifiers are skipped in BTF in the verifier while walking
pointers to avoid program rejection, from Alexei Starovoitov.
7) Fix Makefile for runqslower BPF tool to i) rebuild on libbpf changes and
ii) to fix undefined reference linker errors for older gcc version due to
order of passed gcc parameters, from Yulia Kartseva and Song Liu.
8) Fix a trampoline_count BPF kselftest warning about missing braces around
initializer, from Andrii Nakryiko.
9) Fix up redundant "HAVE" prefix from large INSN limit kernel probe in
bpftool, from Michal Rostecki.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PROVE_LOCKING is selected together with (now default)
CONFIG_VMAP_STACK, kernel enter deadlock during boot.
At the point of checking whether interrupts are enabled or not, the
value of MSR saved on stack is read using the physical address of the
stack. But at this point, when using VMAP stack the DATA MMU
translation has already been re-enabled, leading to deadlock.
Don't use the physical address of the stack when
CONFIG_VMAP_STACK is set.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 028474876f ("powerpc/32: prepare for CONFIG_VMAP_STACK")
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/daeacdc0dec0416d1c587cc9f9e7191ad3068dc0.1581095957.git.christophe.leroy@c-s.fr
The early versions of our kernel user access prevention (KUAP) were
written by Russell and Christophe, and didn't have separate
read/write access.
At some point I picked up the series and added the read/write access,
but I failed to update the usages in futex.h to correctly allow read
and write.
However we didn't notice because of another bug which was causing the
low-level code to always enable read and write. That bug was fixed
recently in commit 1d8f739b07 ("powerpc/kuap: Fix set direction in
allow/prevent_user_access()").
futex_atomic_cmpxchg_inatomic() is passed the user address as %3 and
does:
1: lwarx %1, 0, %3
cmpw 0, %1, %4
bne- 3f
2: stwcx. %5, 0, %3
Which clearly loads and stores from/to %3. The logic in
arch_futex_atomic_op_inuser() is similar, so fix both of them to use
allow_read_write_user().
Without this fix, and with PPC_KUAP_DEBUG=y, we see eg:
Bug: Read fault blocked by AMR!
WARNING: CPU: 94 PID: 149215 at arch/powerpc/include/asm/book3s/64/kup-radix.h:126 __do_page_fault+0x600/0xf30
CPU: 94 PID: 149215 Comm: futex_requeue_p Tainted: G W 5.5.0-rc7-gcc9x-g4c25df5640ae #1
...
NIP [c000000000070680] __do_page_fault+0x600/0xf30
LR [c00000000007067c] __do_page_fault+0x5fc/0xf30
Call Trace:
[c00020138e5637e0] [c00000000007067c] __do_page_fault+0x5fc/0xf30 (unreliable)
[c00020138e5638c0] [c00000000000ada8] handle_page_fault+0x10/0x30
--- interrupt: 301 at cmpxchg_futex_value_locked+0x68/0xd0
LR = futex_lock_pi_atomic+0xe0/0x1f0
[c00020138e563bc0] [c000000000217b50] futex_lock_pi_atomic+0x80/0x1f0 (unreliable)
[c00020138e563c30] [c00000000021b668] futex_requeue+0x438/0xb60
[c00020138e563d60] [c00000000021c6cc] do_futex+0x1ec/0x2b0
[c00020138e563d90] [c00000000021c8b8] sys_futex+0x128/0x200
[c00020138e563e20] [c00000000000b7ac] system_call+0x5c/0x68
Fixes: de78a9c42a ("powerpc: Add a framework for Kernel Userspace Access Protection")
Cc: stable@vger.kernel.org # v5.2+
Reported-by: syzbot+e808452bad7c375cbee6@syzkaller-ppc64.appspotmail.com
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20200207122145.11928-1-mpe@ellerman.id.au
V{PEND,PROP}BASER registers are actually located in VLPI_base frame
of the *redistributor*. Rename their accessors to reflect this fact.
No functional changes.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200206075711.1275-7-yuzenghui@huawei.com
"ITS virtual pending table not cleaning" is already complained inside
its_clear_vpend_valid(), there's no need to trigger a WARN_ON again.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200206075711.1275-6-yuzenghui@huawei.com
In GICv4, we will ensure that level2 vPE table memory is allocated
for the specified vpe_id on all v4 ITS, in its_alloc_vpe_table().
This still works well for the typical GICv4.1 implementation, where
the new vPE table is shared between the ITSs and the RDs.
To make it explicit, let us introduce allocate_vpe_l2_table() to
make sure that the L2 tables are allocated on all v4.1 RDs. We're
likely not need to allocate memory in it because the vPE table is
shared and (L2 table is) already allocated at ITS level, except
for the case where the ITS doesn't share anything (say SVPET == 0,
practically unlikely but architecturally allowed).
The implementation of allocate_vpe_l2_table() is mostly copied from
its_alloc_table_entry().
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200206075711.1275-4-yuzenghui@huawei.com
Currently, we will not set vpe_l1_page for the current RD if we can
inherit the vPE configuration table from another RD (or ITS), which
results in an inconsistency between RDs within the same CommonLPIAff
group.
Let's rename it to vpe_l1_base to indicate the base address of the
vPE configuration table of this RD, and set it properly for *all*
v4.1 redistributors.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200206075711.1275-3-yuzenghui@huawei.com
The Size field of GICv4.1 VPROPBASER register indicates number of
pages minus one and together Page_Size and Size control the vPEID
width. Let's respect this requirement of the architecture.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200206075711.1275-2-yuzenghui@huawei.com
Fix u8 cast reading max_nss from MT_TOP_STRAP_STA register in
mt7615_eeprom_parse_hw_cap routine
Fixes: acf5457fd9 ("mt76: mt7615: read {tx,rx} mask from eeprom")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSQHSd0lITzzeNWNm3h3BK/laaZPAUCXj182AAKCRDh3BK/laaZ
PIiWAQCprdMIBe0u9Rd9cqQYXClOI7PI9oIcpLmkIlHDuUWDgQD/Y4c1UMsN8yQY
d8cYZXMivKKhyY2nRitR1mbv0RPoGwE=
=8hFo
-----END PGP SIGNATURE-----
Merge tag 'fuse-fixes-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse fixes from Miklos Szeredi:
- Fix a regression introduced in v5.1 that triggers WARNINGs for some
fuse filesystems
- Fix an xfstest failure
- Allow overlayfs to be used on top of fuse/virtiofs
- Code and documentation cleanups
* tag 'fuse-fixes-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: use true,false for bool variable
Documentation: filesystems: convert fuse to RST
fuse: Support RENAME_WHITEOUT flag
fuse: don't overflow LLONG_MAX with end offset
fix up iter on short count in fuse_direct_io()
- Fix a bug in Abhi Das's journal head lookup improvements that can cause a
valid journal to be rejected.
- Fix an O_SYNC write handling bug reported by Christoph Hellwig.
-----BEGIN PGP SIGNATURE-----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=+6PA
-----END PGP SIGNATURE-----
Merge tag 'gfs2-for-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull gfs2 fixes from Andreas Gruenbacher:
- Fix a bug in Abhi Das's journal head lookup improvements that can
cause a valid journal to be rejected.
- Fix an O_SYNC write handling bug reported by Christoph Hellwig.
* tag 'gfs2-for-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: fix O_SYNC write handling
gfs2: move setting current->backing_dev_info
gfs2: fix gfs2_find_jhead that returns uninitialized jhead with seq 0
Vasliy Averin noticed that "if seq_file .next function does not change
position index, read after some lseek can generate unexpected output."
and sent in this fix.
-----BEGIN PGP SIGNATURE-----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=tjs3
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.6-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux
Pull orangefs fix from Mike Marshall:
"Debugfs fix for orangefs.
Vasliy Averin noticed that 'if seq_file .next function does not change
position index, read after some lseek can generate unexpected output'
and sent in this fix"
* tag 'for-linus-5.6-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
help_next should increase position index
- Server-to-server copy code from Olga. To use it, client and
both servers must have support, the target server must be able
to access the source server over NFSv4.2, and the target
server must have the inter_copy_offload_enable module
parameter set.
- Improvements and bugfixes for the new filehandle cache,
especially in the container case, from Trond
- Also from Trond, better reporting of write errors.
- Y2038 work from Arnd.
-----BEGIN PGP SIGNATURE-----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=FxLY
-----END PGP SIGNATURE-----
Merge tag 'nfsd-5.6' of git://linux-nfs.org/~bfields/linux
Pull nfsd updates from Bruce Fields:
"Highlights:
- Server-to-server copy code from Olga.
To use it, client and both servers must have support, the target
server must be able to access the source server over NFSv4.2, and
the target server must have the inter_copy_offload_enable module
parameter set.
- Improvements and bugfixes for the new filehandle cache, especially
in the container case, from Trond
- Also from Trond, better reporting of write errors.
- Y2038 work from Arnd"
* tag 'nfsd-5.6' of git://linux-nfs.org/~bfields/linux: (55 commits)
sunrpc: expiry_time should be seconds not timeval
nfsd: make nfsd_filecache_wq variable static
nfsd4: fix double free in nfsd4_do_async_copy()
nfsd: convert file cache to use over/underflow safe refcount
nfsd: Define the file access mode enum for tracing
nfsd: Fix a perf warning
nfsd: Ensure sampling of the write verifier is atomic with the write
nfsd: Ensure sampling of the commit verifier is atomic with the commit
sunrpc: clean up cache entry add/remove from hashtable
sunrpc: Fix potential leaks in sunrpc_cache_unhash()
nfsd: Ensure exclusion between CLONE and WRITE errors
nfsd: Pass the nfsd_file as arguments to nfsd4_clone_file_range()
nfsd: Update the boot verifier on stable writes too.
nfsd: Fix stable writes
nfsd: Allow nfsd_vfs_write() to take the nfsd_file as an argument
nfsd: Fix a soft lockup race in nfsd_file_mark_find_or_create()
nfsd: Reduce the number of calls to nfsd_file_gc()
nfsd: Schedule the laundrette regularly irrespective of file errors
nfsd: Remove unused constant NFSD_FILE_LRU_RESCAN
nfsd: Containerise filecache laundrette
...
Stable bugfixes:
- Fix memory leaks and corruption in readdir # v2.6.37+
- Directory page cache needs to be locked when read # v2.6.37+
New features:
- Convert NFS to use the new mount API
- Add "softreval" mount option to let clients use cache if server goes down
- Add a config option to compile without UDP support
- Limit the number of inactive delegations the client can cache at once
- Improved readdir concurrency using iterate_shared()
Other bugfixes and cleanups:
- More 64-bit time conversions
- Add additional diagnostic tracepoints
- Check for holes in swapfiles, and add dependency on CONFIG_SWAP
- Various xprtrdma cleanups to prepare for 5.7's changes
- Several fixes for NFS writeback and commit handling
- Fix acls over krb5i/krb5p mounts
- Recover from premature loss of openstateids
- Fix NFS v3 chacl and chmod bug
- Compare creds using cred_fscmp()
- Use kmemdup_nul() in more places
- Optimize readdir cache page invalidation
- Lease renewal and recovery fixes
-----BEGIN PGP SIGNATURE-----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=b6+F
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-5.6-1' of git://git.linux-nfs.org/projects/anna/linux-nfs
Puyll NFS client updates from Anna Schumaker:
"Stable bugfixes:
- Fix memory leaks and corruption in readdir # v2.6.37+
- Directory page cache needs to be locked when read # v2.6.37+
New features:
- Convert NFS to use the new mount API
- Add "softreval" mount option to let clients use cache if server goes down
- Add a config option to compile without UDP support
- Limit the number of inactive delegations the client can cache at once
- Improved readdir concurrency using iterate_shared()
Other bugfixes and cleanups:
- More 64-bit time conversions
- Add additional diagnostic tracepoints
- Check for holes in swapfiles, and add dependency on CONFIG_SWAP
- Various xprtrdma cleanups to prepare for 5.7's changes
- Several fixes for NFS writeback and commit handling
- Fix acls over krb5i/krb5p mounts
- Recover from premature loss of openstateids
- Fix NFS v3 chacl and chmod bug
- Compare creds using cred_fscmp()
- Use kmemdup_nul() in more places
- Optimize readdir cache page invalidation
- Lease renewal and recovery fixes"
* tag 'nfs-for-5.6-1' of git://git.linux-nfs.org/projects/anna/linux-nfs: (93 commits)
NFSv4.0: nfs4_do_fsinfo() should not do implicit lease renewals
NFSv4: try lease recovery on NFS4ERR_EXPIRED
NFS: Fix memory leaks
nfs: optimise readdir cache page invalidation
NFS: Switch readdir to using iterate_shared()
NFS: Use kmemdup_nul() in nfs_readdir_make_qstr()
NFS: Directory page cache pages need to be locked when read
NFS: Fix memory leaks and corruption in readdir
SUNRPC: Use kmemdup_nul() in rpc_parse_scope_id()
NFS: Replace various occurrences of kstrndup() with kmemdup_nul()
NFSv4: Limit the total number of cached delegations
NFSv4: Add accounting for the number of active delegations held
NFSv4: Try to return the delegation immediately when marked for return on close
NFS: Clear NFS_DELEGATION_RETURN_IF_CLOSED when the delegation is returned
NFSv4: nfs_inode_evict_delegation() should set NFS_DELEGATION_RETURNING
NFS: nfs_find_open_context() should use cred_fscmp()
NFS: nfs_access_get_cached_rcu() should use cred_fscmp()
NFSv4: pnfs_roc() must use cred_fscmp() to compare creds
NFS: remove unused macros
nfs: Return EINVAL rather than ERANGE for mount parse errors
...
It was reported that the max_t, ilog2, and roundup_pow_of_two macros have
exponential effects on the number of states in the sparse checker.
This patch breaks them up by calculating the "nbuckets" first so that the
"bucket_log" only needs to take ilog2().
In addition, Linus mentioned:
Patch looks good, but I'd like to point out that it's not just sparse.
You can see it with a simple
make net/core/bpf_sk_storage.i
grep 'smap->bucket_log = ' net/core/bpf_sk_storage.i | wc
and see the end result:
1 365071 2686974
That's one line (the assignment line) that is 2,686,974 characters in
length.
Now, sparse does happen to react particularly badly to that (I didn't
look to why, but I suspect it's just that evaluating all the types
that don't actually ever end up getting used ends up being much more
expensive than it should be), but I bet it's not good for gcc either.
Fixes: 6ac99e8f23 ("bpf: Introduce bpf sk local storage")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Link: https://lore.kernel.org/bpf/20200207081810.3918919-1-kafai@fb.com
Commit 7e81a35302 ("bpf: Sockmap, ensure sock lock held during tear
down") introduced sleeping issues inside RCU critical sections and while
holding a spinlock on sockmap/sockhash tear-down. There has to be at least
one socket in the map for the problem to surface.
This adds a test that triggers the warnings for broken locking rules. Not a
fix per se, but rather tooling to verify the accompanying fixes. Run on a
VM with 1 vCPU to reproduce the warnings.
Fixes: 7e81a35302 ("bpf: Sockmap, ensure sock lock held during tear down")
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200206111652.694507-4-jakub@cloudflare.com
We need to have a synchronize_rcu before free'ing the sockhash because any
outstanding psock references will have a pointer to the map and when they
use it, this could trigger a use after free.
This is a sister fix for sockhash, following commit 2bb90e5cc9 ("bpf:
sockmap, synchronize_rcu before free'ing map") which addressed sockmap,
which comes from a manual audit.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200206111652.694507-3-jakub@cloudflare.com