master->transfer_one returns positive value is not a error.
So set ret to 0 when master->transfer_one returns positive value.
Otherwise, I hit "spi_master spi0: failed to transfer one message from queue"
error when my transfer_one callback returns 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The documentation for spi_master.set_cs() says:
assert or deassert chip select, true to assert
i.e. its "enable" parameter uses assertion-level logic.
This does not match the implementation of spi_set_cs(), which calls
spi_master.set_cs() with the wanted logic level of the chip select line,
which depends on the polarity of the chip select signal.
Correct the documentation to match the implementation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 543bb25 "spi: add ability to validate xfer->bits_per_word in SPI
core", the driver can set bits_per_word_mask for the master then the SPI core
will reject transfers that attempt to use an unsupported bits_per_word value.
So we can remove the bits_per_word checking in sc18is602_check_transfer() and
let SPI core handle the checking.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
The implementation in spi_setup() already set spi->bits_per_word = 8 when
spi->bits_per_word is 0 before calling spi->master->setup.
So we don't need to do it again in setup() callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
CONFIG_PM will be set if either or both CONFIG_PM_SLEEP and
CONFIG_PM_RUNTIME is set. Compiling the driver with !CONFIG_PM_SLEEP causes
following compilation warning:
drivers/spi/spi-pxa2xx.c:1270:12: warning: ‘pxa2xx_spi_suspend’ defined but not used [-Wunused-function]
Fix this by using CONFIG_PM_SLEEP instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for specifying the SPI clock phase and polarity, based on the
SDK reference code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit cddb339bad (spi/pxa2xx: convert to dma_request_slave_channel_compat())
converted the driver to use ACPI provided DMA helpers but it forgot to
initialize the platform data for the channels to -1. Failing to do so will
result inadvertent match in the filter function because 0 is a valid
channel number.
Prevent this from happening by initializing both platform data channels
correctly to -1.
Fixes: cddb339bad (spi/pxa2xx: convert to dma_request_slave_channel_compat())
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
On ARM-based SHMOBILE, the rspi driver builds and works fine without the
DMA controller driver, hence relax the dependencies.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have a spi_sh_clear_bit() function, there's no reason not to use it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
- Rephrase the comments about tx/rx_nbits validity checks,
- Remove the stale comment about SPI_3WIRE (the code it refers to was
removed in commit 368ca4e0c7 ("spi:
Eliminate 3WIRE spi_transfer check")).
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi_write_then_read() takes a "void *" for rxbuf, so there's no need to
cast the buffer pointer to "u8 *".
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver name in current code looks like a compatible string which is not
the naming convention for platform drivers.
Fix it and also add modalias since this driver can be built as a module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make the unit of wlen to be byte, and simplify the code to avoid duplicate
code for different wlen cases.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Trent Piepho observed that since the current realistic maximum number of
data lines is four we can pack the spi_transfer struct more efficiently
if we use a bitfield for the number of bits, allowing the fields to fit
in a single byte along with cs_change.
If space becomes an issue further optimiation is possible by only using
the constants and packing the values chosen for them.
Reported-by: Trent Piepho <tpiepho@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We already has NULL test for master after calling spi_alloc_master().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
While running stress tests on adding and deleting ftrace instances I hit
this bug:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
IP: selinux_inode_permission+0x85/0x160
PGD 63681067 PUD 7ddbe067 PMD 0
Oops: 0000 [#1] PREEMPT
CPU: 0 PID: 5634 Comm: ftrace-test-mki Not tainted 3.13.0-rc4-test-00033-gd2a6dde-dirty #20
Hardware name: /DG965MQ, BIOS MQ96510J.86A.0372.2006.0605.1717 06/05/2006
task: ffff880078375800 ti: ffff88007ddb0000 task.ti: ffff88007ddb0000
RIP: 0010:[<ffffffff812d8bc5>] [<ffffffff812d8bc5>] selinux_inode_permission+0x85/0x160
RSP: 0018:ffff88007ddb1c48 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000800000 RCX: ffff88006dd43840
RDX: 0000000000000001 RSI: 0000000000000081 RDI: ffff88006ee46000
RBP: ffff88007ddb1c88 R08: 0000000000000000 R09: ffff88007ddb1c54
R10: 6e6576652f6f6f66 R11: 0000000000000003 R12: 0000000000000000
R13: 0000000000000081 R14: ffff88006ee46000 R15: 0000000000000000
FS: 00007f217b5b6700(0000) GS:ffffffff81e21000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033^M
CR2: 0000000000000020 CR3: 000000006a0fe000 CR4: 00000000000007f0
Call Trace:
security_inode_permission+0x1c/0x30
__inode_permission+0x41/0xa0
inode_permission+0x18/0x50
link_path_walk+0x66/0x920
path_openat+0xa6/0x6c0
do_filp_open+0x43/0xa0
do_sys_open+0x146/0x240
SyS_open+0x1e/0x20
system_call_fastpath+0x16/0x1b
Code: 84 a1 00 00 00 81 e3 00 20 00 00 89 d8 83 c8 02 40 f6 c6 04 0f 45 d8 40 f6 c6 08 74 71 80 cf 02 49 8b 46 38 4c 8d 4d cc 45 31 c0 <0f> b7 50 20 8b 70 1c 48 8b 41 70 89 d9 8b 78 04 e8 36 cf ff ff
RIP selinux_inode_permission+0x85/0x160
CR2: 0000000000000020
Investigating, I found that the inode->i_security was NULL, and the
dereference of it caused the oops.
in selinux_inode_permission():
isec = inode->i_security;
rc = avc_has_perm_noaudit(sid, isec->sid, isec->sclass, perms, 0, &avd);
Note, the crash came from stressing the deletion and reading of debugfs
files. I was not able to recreate this via normal files. But I'm not
sure they are safe. It may just be that the race window is much harder
to hit.
What seems to have happened (and what I have traced), is the file is
being opened at the same time the file or directory is being deleted.
As the dentry and inode locks are not held during the path walk, nor is
the inodes ref counts being incremented, there is nothing saving these
structures from being discarded except for an rcu_read_lock().
The rcu_read_lock() protects against freeing of the inode, but it does
not protect freeing of the inode_security_struct. Now if the freeing of
the i_security happens with a call_rcu(), and the i_security field of
the inode is not changed (it gets freed as the inode gets freed) then
there will be no issue here. (Linus Torvalds suggested not setting the
field to NULL such that we do not need to check if it is NULL in the
permission check).
Note, this is a hack, but it fixes the problem at hand. A real fix is
to restructure the destroy_inode() to call all the destructor handlers
from the RCU callback. But that is a major job to do, and requires a
lot of work. For now, we just band-aid this bug with this fix (it
works), and work on a more maintainable solution in the future.
Link: http://lkml.kernel.org/r/20140109101932.0508dec7@gandalf.local.home
Link: http://lkml.kernel.org/r/20140109182756.17abaaa8@gandalf.local.home
Cc: stable@vger.kernel.org
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We see General Protection Fault on RSI in copy_page_rep: that RSI is
what you get from a NULL struct page pointer.
RIP: 0010:[<ffffffff81154955>] [<ffffffff81154955>] copy_page_rep+0x5/0x10
RSP: 0000:ffff880136e15c00 EFLAGS: 00010286
RAX: ffff880000000000 RBX: ffff880136e14000 RCX: 0000000000000200
RDX: 6db6db6db6db6db7 RSI: db73880000000000 RDI: ffff880dd0c00000
RBP: ffff880136e15c18 R08: 0000000000000200 R09: 000000000005987c
R10: 000000000005987c R11: 0000000000000200 R12: 0000000000000001
R13: ffffea00305aa000 R14: 0000000000000000 R15: 0000000000000000
FS: 00007f195752f700(0000) GS:ffff880c7fc20000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000093010000 CR3: 00000001458e1000 CR4: 00000000000027e0
Call Trace:
copy_user_huge_page+0x93/0xab
do_huge_pmd_wp_page+0x710/0x815
handle_mm_fault+0x15d8/0x1d70
__do_page_fault+0x14d/0x840
do_page_fault+0x2f/0x90
page_fault+0x22/0x30
do_huge_pmd_wp_page() tests is_huge_zero_pmd(orig_pmd) four times: but
since shrink_huge_zero_page() can free the huge_zero_page, and we have
no hold of our own on it here (except where the fourth test holds
page_table_lock and has checked pmd_same), it's possible for it to
answer yes the first time, but no to the second or third test. Change
all those last three to tests for NULL page.
(Note: this is not the same issue as trinity's DEBUG_PAGEALLOC BUG
in copy_page_rep with RSI: ffff88009c422000, reported by Sasha Levin
in https://lkml.org/lkml/2013/3/29/103. I believe that one is due
to the source page being split, and a tail page freed, while copy
is in progress; and not a problem without DEBUG_PAGEALLOC, since
the pmd_same check will prevent a miscopy from being made visible.)
Fixes: 97ae17497e ("thp: implement refcounting for huge zero page")
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org # v3.10 v3.11 v3.12
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When queue_mode is NULL_Q_MQ and null_blk is being removed,
blk_cleanup_queue() isn't called to cleanup queue, so the queue
allocated won't be freed.
This patch calls blk_cleanup_queue() for MQ to drain all pending
requests first and release the reference counter of queue kobject, then
blk_mq_free_queue() will be called in queue kobject's release handler
when queue kobject's reference counter drops to zero.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
"Famouse last words: "final pull request" :-)
I'm sending this because Jason Wang's fixes are pretty important
1) Add missing per-cpu stats initialization to ip6_vti. Otherwise
lockdep spits out a call trace. From Li RongQing.
2) Fix NULL oops in wireless hwsim, from Javier Lopez
3) TIPC deferred packet queue unlink must NULL out skb->next to avoid
crashes. From Erik Hugne
4) Fix access to uninitialized buffer in nf_nat netfilter code, from
Daniel Borkmann
5) Fix lifetime of ipv6 loopback and SIT tunnel addresses, otherwise
they basically timeout immediately. From Hannes Frederic Sowa
6) Fix DMA unmapping of TSO packets in bnx2x driver, from Michal
Schmidt
7) Do not allow L2 forwarding offload via macvtap device, the way
things are now it will not end up being forwaded at all. From
Jason Wang
8) Fix transmit queue selection via ndo_dfwd_start_xmit(), fixing
things like applying NETIF_F_LLTX to the wrong device (!!) and
eliding the proper transmit watchdog handling
9) qlcnic driver was not updating tx statistics at all, from Manish
Chopra"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
qlcnic: Fix ethtool statistics length calculation
qlcnic: Fix bug in TX statistics
net: core: explicitly select a txq before doing l2 forwarding
macvlan: forbid L2 fowarding offload for macvtap
bnx2x: fix DMA unmapping of TSO split BDs
ipv6: add link-local, sit and loopback address with INFINITY_LIFE_TIME
bnx2x: prevent WARN during driver unload
tipc: correctly unlink packets from deferred packet queue
ipv6: pcpu_tstats.syncp should be initialised in ip6_vti.c
netfilter: only warn once on wrong seqadj usage
netfilter: nf_nat: fix access to uninitialized buffer in IRC NAT helper
NFC: Fix target mode p2p link establishment
iwlwifi: add new devices for 7265 series
mac80211: move "bufferable MMPDU" check to fix AP mode scan
mac80211_hwsim: Fix NULL pointer dereference
- fix off-by-one in xfs_attr3_rmt_verify
- fix missing destroy_work_on_stack() in xfs_bmapi_allocate
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=Xpq3
-----END PGP SIGNATURE-----
Merge tag 'xfs-for-linus-v3.13-rc8' of git://oss.sgi.com/xfs/xfs
Pull xfs bugfixes from Ben Myers:
"Here we have a bugfix for an off-by-one in the remote attribute
verifier that results in a forced shutdown which you can hit with v5
superblock by creating a 64k xattr, and a fix for a missing
destroy_work_on_stack() in the allocation worker.
It's a bit late, but they are both fairly straightforward"
* tag 'xfs-for-linus-v3.13-rc8' of git://oss.sgi.com/xfs/xfs:
xfs: Calling destroy_work_on_stack() to pair with INIT_WORK_ONSTACK()
xfs: fix off-by-one error in xfs_attr3_rmt_verify
Pull LED fix from Bryan Wu:
"Pali Rohár and Pavel Machek reported the LED of Nokia N900 doesn't
work with our latest 3.13-rc6 kernel. Milo fixed the regression here"
* 'leds-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: lp5521/5523: Remove duplicate mutex
- Recent commits modifying the lists of C-states in the intel_idle
driver introduced bugs leading to crashes on some systems. Two
fixes from Jiang Liu.
- The ACPI AC driver should receive all types of notifications, but
recent change made it ignore some of them. Fix from Alexander Mezin.
- intel_pstate's validity checks for MSRs it depends on are not
sufficient to catch the lack of support in nested KVM setups, so
they are extended to cover that case. From Dirk Brandewie.
- NEC LZ750/LS has a botched up _BIX method in its ACPI tables, so our
ACPI battery driver needs a quirk for it. From Lan Tianyu.
- The tpm_ppi driver sometimes leaks memory allocated by acpi_get_name().
Fix from Jiang Liu.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Eqc0
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.13-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Recent commits modifying the lists of C-states in the intel_idle
driver introduced bugs leading to crashes on some systems. Two fixes
from Jiang Liu.
- The ACPI AC driver should receive all types of notifications, but
recent change made it ignore some of them. Fix from Alexander Mezin.
- intel_pstate's validity checks for MSRs it depends on are not
sufficient to catch the lack of support in nested KVM setups, so they
are extended to cover that case. From Dirk Brandewie.
- NEC LZ750/LS has a botched up _BIX method in its ACPI tables, so our
ACPI battery driver needs a quirk for it. From Lan Tianyu.
- The tpm_ppi driver sometimes leaks memory allocated by
acpi_get_name(). Fix from Jiang Liu.
* tag 'pm+acpi-3.13-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
intel_idle: close avn_cstates array with correct marker
Revert "intel_idle: mark states tables with __initdata tag"
ACPI / Battery: Add a _BIX quirk for NEC LZ750/LS
intel_pstate: Add X86_FEATURE_APERFMPERF to cpu match parameters.
ACPI / TPM: fix memory leak when walking ACPI namespace
ACPI / AC: change notification handler type to ACPI_ALL_NOTIFY
It only contains one fix for the rtsx_pcr driver. Without it we see a
kernel panic on some machines, when resuming from suspend to RAM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=Dmc7
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-fixes
Pull MFD fix from Samuel Ortiz:
"This is the 2nd MFD pull request for 3.13
It only contains one fix for the rtsx_pcr driver. Without it we see a
kernel panic on some machines, when resuming from suspend to RAM"
* tag 'mfd-fixes-3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-fixes:
mfd: rtsx_pcr: Disable interrupts before cancelling delayed works
It can be a problem when a pattern is loaded via the firmware interface.
LP55xx common driver has already locked the mutex in 'lp55xx_firmware_loaded()'.
So it should be deleted.
On the other hand, locks are required in store_engine_load()
on updating program memory.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Cc: <stable@vger.kernel.org>
In case CONFIG_DEBUG_OBJECTS_WORK is defined, it is needed to
call destroy_work_on_stack() which frees the debug object to pair
with INIT_WORK_ONSTACK().
Signed-off-by: Liu, Chuansheng <chuansheng.liu@intel.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 6f96b3063c)
With CRC check is enabled, if trying to set an attributes value just
equal to the maximum size of XATTR_SIZE_MAX would cause the v3 remote
attr write verification procedure failure, which would yield the back
trace like below:
<snip>
XFS (sda7): Internal error xfs_attr3_rmt_write_verify at line 191 of file fs/xfs/xfs_attr_remote.c
<snip>
Call Trace:
[<ffffffff816f0042>] dump_stack+0x45/0x56
[<ffffffffa0d99c8b>] xfs_error_report+0x3b/0x40 [xfs]
[<ffffffffa0d96edd>] ? _xfs_buf_ioapply+0x6d/0x390 [xfs]
[<ffffffffa0d99ce5>] xfs_corruption_error+0x55/0x80 [xfs]
[<ffffffffa0dbef6b>] xfs_attr3_rmt_write_verify+0x14b/0x1a0 [xfs]
[<ffffffffa0d96edd>] ? _xfs_buf_ioapply+0x6d/0x390 [xfs]
[<ffffffffa0d97315>] ? xfs_bdstrat_cb+0x55/0xb0 [xfs]
[<ffffffffa0d96edd>] _xfs_buf_ioapply+0x6d/0x390 [xfs]
[<ffffffff81184cda>] ? vm_map_ram+0x31a/0x460
[<ffffffff81097230>] ? wake_up_state+0x20/0x20
[<ffffffffa0d97315>] ? xfs_bdstrat_cb+0x55/0xb0 [xfs]
[<ffffffffa0d9726b>] xfs_buf_iorequest+0x6b/0xc0 [xfs]
[<ffffffffa0d97315>] xfs_bdstrat_cb+0x55/0xb0 [xfs]
[<ffffffffa0d97906>] xfs_bwrite+0x46/0x80 [xfs]
[<ffffffffa0dbfa94>] xfs_attr_rmtval_set+0x334/0x490 [xfs]
[<ffffffffa0db84aa>] xfs_attr_leaf_addname+0x24a/0x410 [xfs]
[<ffffffffa0db8893>] xfs_attr_set_int+0x223/0x470 [xfs]
[<ffffffffa0db8b76>] xfs_attr_set+0x96/0xb0 [xfs]
[<ffffffffa0db13b2>] xfs_xattr_set+0x42/0x70 [xfs]
[<ffffffff811df9b2>] generic_setxattr+0x62/0x80
[<ffffffff811e0213>] __vfs_setxattr_noperm+0x63/0x1b0
[<ffffffff81307afe>] ? evm_inode_setxattr+0xe/0x10
[<ffffffff811e0415>] vfs_setxattr+0xb5/0xc0
[<ffffffff811e054e>] setxattr+0x12e/0x1c0
[<ffffffff811c6e82>] ? final_putname+0x22/0x50
[<ffffffff811c708b>] ? putname+0x2b/0x40
[<ffffffff811cc4bf>] ? user_path_at_empty+0x5f/0x90
[<ffffffff811bdfd9>] ? __sb_start_write+0x49/0xe0
[<ffffffff81168589>] ? vm_mmap_pgoff+0x99/0xc0
[<ffffffff811e07df>] SyS_setxattr+0x8f/0xe0
[<ffffffff81700c2d>] system_call_fastpath+0x1a/0x1f
Tests:
setfattr -n user.longxattr -v `perl -e 'print "A"x65536'` testfile
This patch fix it to check the remote EA size is greater than the
XATTR_SIZE_MAX rather than more than or equal to it, because it's
valid if the specified EA value size is equal to the limitation as
per VFS setxattr interface.
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 85dd0707f0)
o Consider number of Tx queues while calculating the length of
Tx statistics as part of ethtool stats.
o Calculate statistics lenght properly for 82xx and 83xx adapter
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver was not updating TX stats so it was not populating
statistics in `ifconfig` command output.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven
Mark Brown
Axel Lin
Mika Westerberg
Linus Torvalds
Steven Rostedt
Hugh Dickins
Ming Lei
Milo Kim
Chuansheng Liu
Jie Liu
Shahed Shaikh
Manish Chopra