tx_ack() wasn't checking the endpoint state and consequently would
attempt to post the p2p 0B read on an endpoint/QP that is closing or
aborting. This causes a NULL pointer dereference crash.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There exists a race condition when using wait_queue_head_t objects
that are declared on the stack. This was being done in a few places
where we are sending work requests to the FW and awaiting replies, but
we don't have an endpoint structure with an embedded c4iw_wr_wait
struct. So the code was allocating it locally on the stack. Bad
design. The race is:
1) thread on cpuX declares the wait_queue_head_t on the stack, then
posts a firmware WR with that wait object ptr as the cookie to be
returned in the WR reply. This thread will proceed to block in
wait_event_timeout() but before it does:
2) An interrupt runs on cpuY with the WR reply. fw6_msg() handles
this and calls c4iw_wake_up(). c4iw_wake_up() sets the condition
variable in the c4iw_wr_wait object to TRUE and will call
wake_up(), but before it calls wake_up():
3) The thread on cpuX calls c4iw_wait_for_reply(), which calls
wait_event_timeout(). The wait_event_timeout() macro checks the
condition variable and returns immediately since it is TRUE. So
this thread never blocks/sleeps. The function then returns
effectively deallocating the c4iw_wr_wait object that was on the
stack.
4) So at this point cpuY has a pointer to the c4iw_wr_wait object
that is no longer valid. Further its pointing to a stack frame
that might now be in use by some other context/thread. So cpuY
continues execution and calls wake_up() on a ptr to a wait object
that as been effectively deallocated.
This race, when it hits, can cause a crash in wake_up(), which I've
seen under heavy stress. It can also corrupt the referenced stack
which can cause any number of failures.
The fix:
Use struct completion, which supports on-stack declarations.
Completions use a spinlock around setting the condition to true and
the wake up so that steps 2 and 4 above are atomic and step 3 can
never happen in-between.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Fix
drivers/infiniband/ulp/srp/ib_srp.c: In function 'srp_handle_recv':
drivers/infiniband/ulp/srp/ib_srp.c:1150: warning: cast to pointer from integer of different size
drivers/infiniband/ulp/srp/ib_srp.c: In function 'srp_send_completion':
drivers/infiniband/ulp/srp/ib_srp.c🔢 warning: cast to pointer from integer of different size
by adding an intermediate cast to uintptr_t.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Acked-by: David Dillow <dillowda@ornl.gov>
We want the ucmX, umadX and issmX device nodes to show up under
/dev/infiniband, and additionally ucmX should have mode 0666. Add
appropriate devnode methods to their class structs for this.
Signed-off-by: Roland Dreier <roland@purestorage.com>
We had a script which was looping through the devices returned from
ibstat and attempted to register a SMI agent on an ethernet device.
This caused a kernel panic for IBoE devices that don't have QP0.
Fix this by checking if the QP exists before using it.
Signed-off-by: Ira Weiny <weiny2@llnl.gov>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We want udev to create a device node under /dev/infiniband with
permission 0666 for uverbsX devices, so add a devnode method to set the
appropriate info.
Signed-off-by: Roland Dreier <roland@purestorage.com>
We want udev to create a device node under /dev/infiniband with
permission 0666 for rdma_cm, so add that info to our struct miscdevice.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
After discovering that wide use of prefetch on modern CPUs
could be a net loss instead of a win, net drivers which were
relying on the implicit inclusion of prefetch.h via the list
headers showed up in the resulting cleanup fallout. Give
them an explicit include via the following $0.02 script.
=========================================
#!/bin/bash
MANUAL=""
for i in `git grep -l 'prefetch(.*)' .` ; do
grep -q '<linux/prefetch.h>' $i
if [ $? = 0 ] ; then
continue
fi
( echo '?^#include <linux/?a'
echo '#include <linux/prefetch.h>'
echo .
echo w
echo q
) | ed -s $i > /dev/null 2>&1
if [ $? != 0 ]; then
echo $i needs manual fixup
MANUAL="$i $MANUAL"
fi
done
echo ------------------- 8\<----------------------
echo vi $MANUAL
=========================================
Signed-off-by: Paul <paul.gortmaker@windriver.com>
[ Fixed up some incorrect #include placements, and added some
non-network drivers and the fib_trie.c case - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
Add basic RDMA netlink infrastructure that allows for registration of
RDMA clients for which data is to be exported and supplies message
construction callbacks.
Signed-off-by: Nir Muchtar <nirm@voltaire.com>
[ Reorganize a few things, add CONFIG_NET dependency. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Manual merge of arch/powerpc/kernel/smp.c and add missing scheduler_ipi()
call to arch/powerpc/platforms/cell/interrupt.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The driver reads PCI revision ID from the PCI configuration register
while it's already stored by PCI subsystem in the revision field of
struct pci_dev.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The IW_CM_EVENT_STATUS_xxx values were used in only a couple of places;
cma.c uses -Exxx values instead, and so do the amso1100, cxgb3 and cxgb4
drivers -- only nes was using the enum values (with the mild consequence
that all nes connection failures were treated as generic errors rather
than reported as timeouts or rejections).
We can fix this confusion by getting rid of enum iw_cm_event_status and
using a plain int for struct iw_cm_event.status, and converting nes to
use -Exxx as the other iWARP drivers do.
This also gets rid of the warning
drivers/infiniband/core/cma.c: In function 'cma_iw_handler':
drivers/infiniband/core/cma.c:1333:3: warning: case value '4294967185' not in enumerated type 'enum iw_cm_event_status'
drivers/infiniband/core/cma.c:1336:3: warning: case value '4294967186' not in enumerated type 'enum iw_cm_event_status'
drivers/infiniband/core/cma.c:1332:3: warning: case value '4294967192' not in enumerated type 'enum iw_cm_event_status'
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Faisal Latif <faisal.latif@intel.com>
Commit 44c10138fd ("PCI: Change all drivers to use pci_device->revision")
already converted this driver to using the revision field of struct
pci_dev but commit bb9171448d ("IB/ipath: Misc changes to prepare
for IB7220 introduction") later reverted that change for some strange
reason. Restore the change.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The time limit test now correctly checks against current jiffies to
avoid the hang.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
A few more EEH fixes:
c4iw_wait_for_reply(): detect fatal EEH condition on timeout and
return an error.
The iw_cxgb4 driver was only calling ib_deregister_device() on an EEH
event followed by a ib_register_device() when the device was
reinitialized. However, the RDMA core doesn't allow multiple
iterations of register/deregister by the provider. See
drivers/infiniband/core/sysfs.c: ib_device_unregister_sysfs() where
the kobject ref is held until the device is deallocated in
ib_deallocate_device(). Calling deregister adds this kobj reference,
and then a subsequent register call will generate a WARN_ON() from the
kobject subsystem because the kobject is being initialized but is
already initialized with the ref held.
So the provider must deregister and dealloc when resetting for an EEH
event, then alloc/register to re-initialize. To do this, we cannot
use the device ptr as our ULD handle since it will change with each
reallocation. This commit adds a ULD context struct which is used as
the ULD handle, and then contains the device pointer and other state
needed.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The driver was never really waiting for RDMA_WR/FINI completions
because the condition variable used to determine if the completion
happened was never reset, and this condition variable is reused for
both connection setup and teardown. This causes various driver
crashes under heavy loads due to releasing resources too early.
The fix is to use atomic bits to correctly reset the condition
immediately after the completion is detected.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Parens are missing: '|' has a higher presedence than '?'.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
c4iw_uld_add() must return ERR_PTR() values instead of NULL on failure.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Concurrent ingress CLOSE and ULP ABORT operations causes a crash due
to a race condition where the close path releases the EP lock and then
tries to move the QP state to CLOSED. This must be done inside the EP
lock to avoid the race.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Lustre requires that clients bind to a privileged port number before
connecting to a remote server. On larger clusters (typically more
than about 1000 nodes), the number of privileged ports is exhausted,
resulting in lustre being unusable.
To handle this, we add support for reusable addresses to the rdma_cm.
This mimics the behavior of the socket option SO_REUSEADDR. A user
may set an rdma_cm_id to reuse an address before calling
rdma_bind_addr() (explicitly or implicitly). If set, other
rdma_cm_id's may be bound to the same address, provided that they all
have reuse enabled, and there are no active listens.
If rdma_listen() is called on an rdma_cm_id that has reuse enabled, it
will only succeed if there are no other id's bound to that same
address. The reuse option is exported to user space. The behavior of
the kernel reuse implementation was verified against that given by
sockets.
This patch is derived from a path by Ira Weiny <weiny2@llnl.gov>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
cma_use_port() assumes that the sockaddr is an IPv4 address. Since
IPv6 addressing is supported (and also to support other address
families) make the code more generic in its address handling.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This updates the network drivers so that they don't access the
ethtool_cmd::speed field directly, but use ethtool_cmd_speed()
instead.
For most of the drivers, these changes are purely cosmetic and don't
fix any problem, such as for those 1GbE/10GbE drivers that indirectly
call their own ethtool get_settings()/mii_ethtool_gset(). The changes
are meant to enforce code consistency and provide robustness with
future larger throughputs, at the expense of a few CPU cycles for each
ethtool operation.
All drivers compiled with make allyesconfig ion x86_64 have been
updated.
Tested: make allyesconfig on x86_64 + e1000e/bnx2x work
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fe3cc0d99d ("powerpc: Add
pgprot_writecombine") in benh's tree exposes the pgprot_writecombine()
API to drivers on powerpc. cxgb4 has an open-coded version of the same,
so use the common API now that it's available.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Anton Blanchard <anton@samba.org>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
route: Take the right src and dst addresses in ip_route_newports
ipv4: Fix nexthop caching wrt. scoping.
ipv4: Invalidate nexthop cache nh_saddr more correctly.
net: fix pch_gbe section mismatch warning
ipv4: fix fib metrics
mlx4_en: Removing HW info from ethtool -i report.
net_sched: fix THROTTLED/RUNNING race
drivers/net/a2065.c: Convert release_resource to release_region/release_mem_region
drivers/net/ariadne.c: Convert release_resource to release_region/release_mem_region
bonding: fix rx_handler locking
myri10ge: fix rmmod crash
mlx4_en: updated driver version to 1.5.4.1
mlx4_en: Using blue flame support
mlx4_core: reserve UARs for userspace consumers
mlx4_core: maintain available field in bitmap allocator
mlx4: Add blue flame support for kernel consumers
mlx4_en: Enabling new steering
mlx4: Add support for promiscuous mode in the new steering model.
mlx4: generalization of multicast steering.
mlx4_en: Reporting HW revision in ethtool -i
...
Commit 1765a57533 ("net: make dev->master general") introduced a
test of an uninitialized netdev. Fix the code so the intended netdev
is tested.
Signed-off-by: Roland Dreier <roland@purestorage.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB: Increase DMA max_segment_size on Mellanox hardware
IB/mad: Improve an error message so error code is included
RDMA/nes: Don't print success message at level KERN_ERR
RDMA/addr: Fix return of uninitialized ret value
IB/srp: try to use larger FMR sizes to cover our mappings
IB/srp: add support for indirect tables that don't fit in SRP_CMD
IB/srp: rework mapping engine to use multiple FMR entries
IB/srp: allow sg_tablesize to be set for each target
IB/srp: move IB CM setup completion into its own function
IB/srp: always avoid non-zero offsets into an FMR
The same packet steering mechanism would be used both for IB and Ethernet,
Both multicasts and unicasts.
This commit prepares the general infrastructure for this.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW revision is derived from device ID and rev id.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, each device is assumed to be able only handle 64 KB chunks
during DMA. By giving the segment size a larger value, the block layer
will coalesce more S/G entries together for SRP, allowing larger
requests with the same sg_tablesize setting. The block layer is the
only direct user of it, though a few IOMMU drivers reference it as
well for their *_map_sg coalescing code. pci-gart_64 on x86, and a
smattering on on sparc, powerpc, and ia64.
Since other IB protocols could potentially see larger segments with
this, let's check those:
- iSER is fine, because you limit your maximum request size to 512
KB, so we'll never overrun the page vector in struct iser_page_vec
(128 entries currently). It is independent of the DMA segment size,
and handles multi-page segments already.
- IPoIB is fine, as it maps each page individually, and doesn't use
ib_dma_map_sg().
- RDS appears to do the right thing and has no dependencies on DMA
segment size, but I don't claim to have done a complete audit.
- NFSoRDMA and 9p are OK -- they do not use ib_dma_map_sg(), so they
doesn't care about the coalescing.
- Lustre's ko2iblnd does not care about coalescing -- it properly
walks the returned sg list.
This patch ups the value on Mellanox hardware to 1 GB, which matches
reported firmware limits on mlx4.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There's no reason to print "NetEffect RNIC driver successfully loaded"
at level KERN_ERR (where it will uglify the console on a quiet boot).
Change it to KERN_INFO.
Signed-off-by: Roland Dreier <roland@purestorage.com>
* 'kvm-updates/2.6.39' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (55 commits)
KVM: unbreak userspace that does not sets tss address
KVM: MMU: cleanup pte write path
KVM: MMU: introduce a common function to get no-dirty-logged slot
KVM: fix rcu usage in init_rmode_* functions
KVM: fix kvmclock regression due to missing clock update
KVM: emulator: Fix permission checking in io permission bitmap
KVM: emulator: Fix io permission checking for 64bit guest
KVM: SVM: Load %gs earlier if CONFIG_X86_32_LAZY_GS=n
KVM: x86: Remove useless regs_page pointer from kvm_lapic
KVM: improve comment on rcu use in irqfd_deassign
KVM: MMU: remove unused macros
KVM: MMU: cleanup page alloc and free
KVM: MMU: do not record gfn in kvm_mmu_pte_write
KVM: MMU: move mmu pages calculated out of mmu lock
KVM: MMU: set spte accessed bit properly
KVM: MMU: fix kvm_mmu_slot_remove_write_access dropping intermediate W bits
KVM: Start lock documentation
KVM: better readability of efer_reserved_bits
KVM: Clear async page fault hash after switching to real mode
KVM: VMX: Initialize vm86 TSS only once.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (170 commits)
[SCSI] scsi_dh_rdac: Add MD36xxf into device list
[SCSI] scsi_debug: add consecutive medium errors
[SCSI] libsas: fix ata list corruption issue
[SCSI] hpsa: export resettable host attribute
[SCSI] hpsa: move device attributes to avoid forward declarations
[SCSI] scsi_debug: Logical Block Provisioning (SBC3r26)
[SCSI] sd: Logical Block Provisioning update
[SCSI] Include protection operation in SCSI command trace
[SCSI] hpsa: fix incorrect PCI IDs and add two new ones (2nd try)
[SCSI] target: Fix volume size misreporting for volumes > 2TB
[SCSI] bnx2fc: Broadcom FCoE offload driver
[SCSI] fcoe: fix broken fcoe interface reset
[SCSI] fcoe: precedence bug in fcoe_filter_frames()
[SCSI] libfcoe: Remove stale fcoe-netdev entries
[SCSI] libfcoe: Move FCOE_MTU definition from fcoe.h to libfcoe.h
[SCSI] libfc: introduce __fc_fill_fc_hdr that accepts fc_hdr as an argument
[SCSI] fcoe, libfc: initialize EM anchors list and then update npiv EMs
[SCSI] Revert "[SCSI] libfc: fix exchange being deleted when the abort itself is timed out"
[SCSI] libfc: Fixing a memory leak when destroying an interface
[SCSI] megaraid_sas: Version and Changelog update
...
Fix up trivial conflicts due to whitespace differences in
drivers/scsi/libsas/{sas_ata.c,sas_scsi_host.c}
Commit b23dd4fe42 ("ipv4: Make output route lookup return rtable
directly") resulted in leaving ret uninitialized, where it may later
be returned.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In most cases, get_user_pages and get_user_pages_fast should be used
to pin user pages in memory. But sometimes, some special flags except
FOLL_GET, FOLL_WRITE and FOLL_FORCE are needed, for example in
following patch, KVM needs FOLL_HWPOISON. To support these users,
__get_user_pages is exported directly.
There are some symbol name conflicts in infiniband driver, fixed them too.
Signed-off-by: Huang Ying <ying.huang@intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Michel Lespinasse <walken@google.com>
CC: Roland Dreier <roland@kernel.org>
CC: Ralph Campbell <infinipath@qlogic.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1480 commits)
bonding: enable netpoll without checking link status
xfrm: Refcount destination entry on xfrm_lookup
net: introduce rx_handler results and logic around that
bonding: get rid of IFF_SLAVE_INACTIVE netdev->priv_flag
bonding: wrap slave state work
net: get rid of multiple bond-related netdevice->priv_flags
bonding: register slave pointer for rx_handler
be2net: Bump up the version number
be2net: Copyright notice change. Update to Emulex instead of ServerEngines
e1000e: fix kconfig for crc32 dependency
netfilter ebtables: fix xt_AUDIT to work with ebtables
xen network backend driver
bonding: Improve syslog message at device creation time
bonding: Call netif_carrier_off after register_netdevice
bonding: Incorrect TX queue offset
net_sched: fix ip_tos2prio
xfrm: fix __xfrm_route_forward()
be2net: Fix UDP packet detected status in RX compl
Phonet: fix aligned-mode pipe socket buffer header reserve
netxen: support for GbE port settings
...
Fix up conflicts in drivers/staging/brcm80211/brcmsmac/wl_mac80211.c
with the staging updates.
Now that we can get larger SG lists, we can take advantage of HCAs that
allow us to use larger FMR sizes. In many cases, we can use up to 512
entries, so start there and work our way down.
Signed-off-by: David Dillow <dillowda@ornl.gov>
This allows us to guarantee the ability to submit up to 8 MB requests
based on the current value of SCSI_MAX_SG_CHAIN_SEGMENTS. While FMR will
usually condense the requests into 8 SG entries, it is imperative that
the target support external tables in case the FMR mapping fails or is
not supported.
We add a safety valve to allow targets without the needed support to
reap the benefits of the large tables, but fail in a manner that lets
the user know that the data didn't make it to the device. The user must
add "allow_ext_sg=1" to the target parameters to indicate that the
target has the needed support.
If indirect_sg_entries is not specified in the modules options, then
the sg_tablesize for the target will default to cmd_sg_entries unless
overridden by the target options.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Instead of forcing all of the S/G entries to fit in one FMR, and falling
back to indirect descriptors if that fails, allow the use of as many
FMRs as needed to map the request. This lays the groundwork for allowing
indirect descriptor tables that are larger than can fit in the command
IU, but should marginally improve performance now by reducing the number
of indirect descriptors needed.
We increase the minimum page size for the FMR pool to 4K, as larger
pages help increase the coverage of each FMR, and it is rare that the
kernel would send down a request with scattered 512 byte fragments.
This patch also move some of the target initialization code afte the
parsing of options, to keep it together with the new code that needs to
allocate memory based on the options given.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Different configurations of target software allow differing max sizes of
the command IU. Allowing this to be changed per-target allows all
targets on an initiator to get an optimal setting.
We deprecate srp_sg_tablesize and replace it with cmd_sg_entries in
preparation for allowing more indirect descriptors than can fit in the
IU.
Signed-off-by: David Dillow <dillowda@ornl.gov>
It is unclear exactly how this code works around Mellanox SRP targets,
or if the problem is on the target side or in the HCA itself. In an
abundance of caution, we should always enable the workaround.
Signed-off-by: David Dillow <dillowda@ornl.gov>
rdma_destroy_id currently uses the global rdma cm 'lock' to test if an
rdma_cm_id has been bound to a device. This prevents an active
address resolution callback handler from assigning a device to the
rdma_cm_id after rdma_destroy_id checks for one.
Instead, we can replace the use of the global lock around the check to
the rdma_cm_id device pointer by setting the id state to destroying,
then flushing all active callbacks. The latter is accomplished by
acquiring and releasing the handler_mutex. Any active handler will
complete first, and any newly scheduled handlers will find the
rdma_cm_id in an invalid state.
In addition to optimizing the current locking scheme, the use of the
rdma_cm_id mutex is a more intuitive synchronization mechanism than
that of the global lock. These changes are based on feedback from
Doug Ledford <dledford@redhat.com> while he was trying to debug a
crash in the rdma cm destroy path.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This problem was reported by Moni Shoua <monis@mellanox.com> and Amir
Vadai <amirv@mellanox.com>:
When destroying a cm_id from a context of a work queue and if
the lap_state of this cm_id is IB_CM_LAP_SENT, we need to
release the reference of this id that was taken upon the send
of the LAP message. Otherwise, if the expected APR message
gets lost, it is only after a long time that the reference
will be released, while during that the work handler thread is
not available to process other things.
It turns out that we need to cancel any pending LAP messages whenever
we transition out of the IB_CM_ESTABLISH state. This occurs when
disconnecting - either sending or receiving a DREQ. It can also
happen in a corner case where we receive a REJ message after sending
an RTU, followed by a LAP. Add checks and cancel any outstanding LAP
messages in these three cases.
Canceling the LAP when sending a DREQ fixes the destroy problem
reported by Moni. When a cm_id is destroyed in the IB_CM_ESTABLISHED
state, it sends a DREQ to the remote side to notify the peer that the
connection is going away.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When processing a SIDR REQ, the ib_cm allocates a new cm_id. The
refcount of the cm_id is initialized to 1. However, cm_process_work
will decrement the refcount after invoking all callbacks. The result
is that the cm_id will end up with refcount set to 0 by the end of the
sidr req handler.
If a user tries to destroy the cm_id, the destruction will proceed,
under the incorrect assumption that no other threads are referencing
the cm_id. This can lead to a crash when the cm callback thread tries
to access the cm_id.
This problem was noticed as part of a larger investigation with kernel
crashes in the rdma_cm when running on a real time OS.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Doug Ledford and Red Hat reported a crash when running the rdma_cm on
a real-time OS. The crash has the following call trace:
cm_process_work
cma_req_handler
cma_disable_callback
rdma_create_id
kzalloc
init_completion
cma_get_net_info
cma_save_net_info
cma_any_addr
cma_zero_addr
rdma_translate_ip
rdma_copy_addr
cma_acquire_dev
rdma_addr_get_sgid
ib_find_cached_gid
cma_attach_to_dev
ucma_event_handler
kzalloc
ib_copy_ah_attr_to_user
cma_comp
[ preempted ]
cma_write
copy_from_user
ucma_destroy_id
copy_from_user
_ucma_find_context
ucma_put_ctx
ucma_free_ctx
rdma_destroy_id
cma_exch
cma_cancel_operation
rdma_node_get_transport
rt_mutex_slowunlock
bad_area_nosemaphore
oops_enter
They were able to reproduce the crash multiple times with the
following details:
Crash seems to always happen on the:
mutex_unlock(&conn_id->handler_mutex);
as conn_id looks to have been freed during this code path.
An examination of the code shows that a race exists in the request
handlers. When a new connection request is received, the rdma_cm
allocates a new connection identifier. This identifier has a single
reference count on it. If a user calls rdma_destroy_id() from another
thread after receiving a callback, rdma_destroy_id will proceed to
destroy the id and free the associated memory. However, the request
handlers may still be in the process of running. When control returns
to the request handlers, they can attempt to access the newly created
identifiers.
Fix this by holding a reference on the newly created rdma_cm_id until
the request handler is through accessing it.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Set the M_Key field in SubnGet and SugnGetResp MADs based on correctly
interpreting the protection level specified in the M_KeyProtBits field.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For active and far-EQ cables use an LE2 value of 0 for improved SI.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
- Show whether the SQ is in onchip memory or not.
- Dump both SQ and RQ QIDs.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This at least kicks the user mode applications that are watching for
device events.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Set the ULP mode for initial RDMA connection setup to the proper DDP
mode. This avoids wasting some HW resources while in streaming mode.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This avoids the CIDX_INC overflow issue with T4A2 when running
kernel RDMA applications.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Unloading iw_cxgb4 can crash due to the unload code trying to use
db_drop_task, which is uninitialized. So remove this dead code.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
I intend to turn struct flowi into a union of AF specific flowi
structs. There will be a common structure that each variant includes
first, much like struct sock_common.
This is the first step to move in that direction.
Signed-off-by: David S. Miller <davem@davemloft.net>
The idea here is this minimizes the number of places one has to edit
in order to make changes to how flows are defined and used.
Signed-off-by: David S. Miller <davem@davemloft.net>
This pactch has iser export the address and port
of the endpoint.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix a bug which causes the driver to return incorrect MADs as a
response to Set(PortInfo) which sets the link width to 0xFF or link
speed to 0xF.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There is a double completion associated with error handling for RC QPs.
The sequence is:
- The do_rc_ack() routine fields an RNR nack and there are 0
rnr_retries configured on the QP.
- qib_error_qp() stops the pending timer
- qib_rc_send_complete() is called from sdma_complete()
- qib_rc_send_complete() starts the timer because the msb of the psn
just completed says an ack is needed.
- a bunch of flushes occur as ipoib posts WQEs to an error'ed QP
- rc_timeout() calls qib_restart_rc()
- qib_restart_rc() calls qib_send_complete() with a
IB_WC_RETRY_EXC_ERR on a wqe that has already been completed in the
past
The fix avoids starting the timer since another packet will never
arrive.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
dev->master is now tightly connected to bonding driver. This patch makes
this pointer more general and ready to be used by others.
- netdev_set_master() - bond specifics moved to new function
netdev_set_bond_master()
- introduced netif_is_bond_slave() to check if device is a bonding slave
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following panic BUG_ON occurs during qib testing:
Kernel BUG at include/linux/timer.h:82
RIP [<ffffffff881f7109>] :ib_qib:start_timer+0x73/0x89
RSP <ffffffff80425bd0>
<0>Kernel panic - not syncing: Fatal exception
<0>Dumping qib trace buffer from panic
qib_set_lid INFO: IB0:1 got a lid: 0xf8
Done dumping qib trace buffer
BUG: warning at kernel/panic.c:137/panic() (Tainted: G
The flaw is due to a missing state test when processing responses that
results in an add_timer() call when the same timer is already queued.
This code was executing in parallel with a QP destroy on another CPU
that had changed the state to reset, but the missing test caused to
response handling code to run on into the panic.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
nes_port_ibevent() should not be called when the nes RDMA device is not
registered with the RDMA core. Add missing checks of of_device_registered flag.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA: Update missed conversion of flush_scheduled_work()
RDMA/ucma: Copy iWARP route information on queries
RDMA/amso1100: Fix compile warnings
RDMA/cxgb4: Set the correct device physical function for iWARP connections
RDMA/cxgb4: Limit MAXBURST EQ context field to 256B
IB/qib: Hold link for TX SERDES settings
mlx4_core: Add ConnectX-3 device IDs
Commit f06267104d ("RDMA: Update workqueue usage") introduced ib_wq
and removed the use of flush_scheduled_work(); however, during the merge
process one chunk was lost in ib_sa_remove_one(). Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For iWARP rdma_cm ids, the "route" information is the L2 src and
next hop addresses.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix compile warnings on 32-bit by using "0" instead of "(u64) NULL" to
assign to "c2_vq_req->reply_msg".
Signed-off-by: Ralf Thielow <ralf.thielow@googlemail.com>
[ Change from "(unsigned long) NULL" to plain old "0" as suggested by
Bart Van Assche <bvanassche@acm.org>. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
The PF passed to FW was 0, causing PCI failures in an SR-IOV environment.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
MAXBURST cannot exceed 256B for on-chip queues. With a 512B MAXBURST,
we can lock up the chip.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Hold the IB link at DISABLED until we get the correct TX settings
on mezz boards.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA: Update workqueue usage
RDMA/nes: Fix incorrect SFP+ link status detection on driver init
RDMA/nes: Fix SFP+ link down detection issue with switch port disable
RDMA/nes: Generate IB_EVENT_PORT_ERR/PORT_ACTIVE events
RDMA/nes: Fix bonding on iw_nes
IB/srp: Test only once whether iu allocation succeeded
IB/mlx4: Handle protocol field in multicast table
RDMA: Use vzalloc() to replace vmalloc()+memset(0)
mlx4_{core, ib, en}: Fix driver when sizeof (phys_addr_t) > sizeof (long)
IB/mthca: Fix driver when sizeof (phys_addr_t) > sizeof (long)
* ib_wq is added, which is used as the common workqueue for infiniband
instead of the system workqueue. All system workqueue usages
including flush_scheduled_work() callers are converted to use and
flush ib_wq.
* cancel_delayed_work() + flush_scheduled_work() converted to
cancel_delayed_work_sync().
* qib_wq is removed and ib_wq is used instead.
This is to prepare for deprecation of flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During iw_nes initialization the link status for SFP+ PHY is always
detected as "up" regardless of real state (cable either connected or
disconnected). Add SFP+ PHY specific link status detection to the
iw_nes initialization procedure. Use link status recheck for
netdev_open to detect delayed state updates.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In case of SFP+ PHY, link status check at interrupt processing can
give false results. For proper link status change detection a delayed
recheck is needed to give nes registers time to settle. Add a
periodic link status recheck scheduled at interrupt to detect
potential delayed registers state changes.
Addresses: http://bugs.openfabrics.org/bugzilla/show_bug.cgi?id=2117
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Depending on link state change, IB_EVENT_PORT_ERR or
IB_EVENT_PORT_ACTIVE should be generated when handling MAC interrupts.
Plugging in a cable happens to result in series of interrupts changing
driver's link state a number of times before finally staying at link
up (e.g. link up, link down, link up, link down, ..., link up). To
prevent sending series of redundant IB_EVENT_PORT_ACTIVE and
IB_EVENT_PORT_ERR events, we use a timer to debounce them in
nes_port_ibevent().
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable configuring bonds on nes devices by adding missing support for
master net_device to the driver.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Merge the two tests in srp_queuecommand() of whether information unit
allocation succeeded into one. An intended side effect of this change
is that we fix the warning:
drivers/infiniband/ulp/srp/ib_srp.c: In function 'srp_queuecommand':
drivers/infiniband/ulp/srp/ib_srp.c:1116: warning: 'req' may be used uninitialized in this function
(seen with CONFIG_CC_OPTIMIZE_FOR_SIZE=y at least with gcc 4.4.4)
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The newest device firmware stores IB vs. Ethernet protocol in two bits
in members_count field of multicast group table (0: Infiniband, 1:
Ethernet). When changing the QP members count for a multicast group,
it important not to reset this information. When calling multicast
attach first time, the protocol type should be specified. In this
patch we always set it IB, but in the future we will handle Ethernet
too. When looking for a QP, the protocol type shoud be checked too.
Signed-off-by: Aleksey Senin <alekseys@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some systems have PCI addresses that don't fit in unsigned long (eg some
32-bit PowerPC 440 systems have 36-bit bus addresses). Fix up mlx4 drivers
by using phys_addr_t where appropriate, so we don't truncate any PCI
resource addresses before ioremapping them.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some systems have PCI addresses that don't fit in unsigned long (eg some
32-bit PowerPC 440 systems have 36-bit bus addresses). Fix up the driver
by using phys_addr_t where appropriate, so we don't truncate any PCI
resource addresses before ioremapping them.
Signed-off-by: John L. Burr <jlburr@cadence.com>
[ Update to apply to current driver source. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (42 commits)
IB/qib: Fix refcount leak in lkey/rkey validation
IB/qib: Improve SERDES tunning on QMH boards
IB/qib: Unnecessary delayed completions on RC connection
IB/qib: Issue pre-emptive NAKs on eager buffer overflow
IB/qib: RDMA lkey/rkey validation is inefficient for large MRs
IB/qib: Change QPN increment
IB/qib: Add fix missing from earlier patch
IB/qib: Change receive queue/QPN selection
IB/qib: Fix interrupt mitigation
IB/qib: Avoid duplicate writes to the rcv head register
IB/qib: Add a few new SERDES tunings
IB/qib: Reset packet list after freeing
IB/qib: New SERDES init routine and improvements to SI quality
IB/qib: Clear WAIT_SEND flags when setting QP to error state
IB/qib: Fix context allocation with multiple HCAs
IB/qib: Fix multi-Florida HCA host panic on reboot
IB/qib: Handle transitions from ACTIVE_DEFERRED to ACTIVE better
IB/qib: UD send with immediate receive completion has wrong size
IB/qib: Set port physical state even if other fields are invalid
IB/qib: Generate completion callback on errors
...
The mr optimization introduced a reference count leak on an exception
test. The lock/refcount manipulation is moved down and the problematic
exception test now calls bail to insure that the lock is released.
Additional fixes as suggested by Ralph Campbell <ralph.campbell@qlogic.org>:
- reduce lock scope of dma regions
- use explicit values on returns vs. automatic ret value
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Improve the QMH SERDES tunning on initial driver load by having the
driver go through a link state change.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently on receipt of a response message (ACKs, RDMA Response,
Atomic Responses etc.) if the SDMA completion counter is not advanced
the driver delays the completion of the WQE. In most cases this is
overly pessimistic as the response (ACK) to a previously transmitted
send implies that the send is complete. Ensure that SDMA queue is
progressed appropriately before determining if a send has delayed
completions.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Under congestion resulting in eager buffer overflow attempt to send
pre-emptive NAKs if header queue entries with TID errors are generated
and a valid header is present. This prevents long timeouts and flow
restarts if a trailing set of packets are dropped due to eager
overflows. Pre-emptive NAKs are currently only supported for RDMA
writes.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current code loops during rkey/lkey validiation to isolate the MR
for the RDMA, which is expensive when the current operation is inside
a very large memory region.
This fix optimizes rkey/lkey validation routines for user memory
regions and fast memory regions. The MR entry can be isolated by
shifts/mods instead of looping. The existing loop is preserved for
phys memory regions for now.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Changing from +1 to +2 allows for better QP distribution across
receive contexts.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The upstream code was missing part of a receive/error race fix from
the internal tree. Add the missing part, which makes future merges
possible.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The basic idea is that on SusieQ, the difficult part of mapping QPN to
context is handled by the mapping registers so the generic QPN
allocation doesn't need to worry about chip specifics. For Monty and
Linda, there is no mapping table so the qpt->mask (same as
dd->qpn_mask), is used to see if the QPN to context falls within
[zero..dd->n_krcv_queues).
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For SusieQ we need to write to the interrupt timer register before
updating the header queue head with interrupt count. This is to
ensure that the timer is enabled properly and a receive available
interrupt is delivered. Otherwise this interrupt can be lost if the
receiver header/eager queues are full before the timer is enabled.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Avoid duplicate writes to the head register as this can lead to lost
interrupts if the context goes full before the second write is done.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add new SERDES tuning to aid manufacturing.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Reset the list pointers after freeing the SDMA packet list. This is
done to any potential double-free cases.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Implement new SERDES initialization routine and improvements to signal
integrity -- disable LE1 adaptation, disable LOS after link-up, set
better SERDES parameters.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If these flags are set when the QP is transitioned to the error state,
it will wait until the flags are cleared, which may never happen if
the error transition is due to a link going down.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The driver was incorrectly choosing HCAs on which to allocate new user
contexts based on overall count of usable ports regardless whether the
usable port was on the currently selected HCA.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add check when setting configured contexts that the value does not
exceed the number of contexts allocated for the card. If the value
exceeds the already allocated count, set it to what is already
allocated.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the link transitions from ACTIVE_DEFERRED to ACTIVE, the driver
only sees the ACTIVE state. With this change, it will check whether
the state was already ACTIVE and if so, it will not generated IB
events and will not clear symbol error counts.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code to generate receive completion entries for UD send with
immediate contains the wrong payload length. This is because when the
code to compute the payload size was moved, the value of hdrsize
didn't get moved too. The fix is to update tlen directly.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IBTA vol. 1 release 1.2.1 spec. says:
C14-24.2.1: If PortInfo:Portstate=Down, then a SubnSet(PortInfo) shall
make any changes it specifies to PortInfo:PortPhysicalState; any other
result is vendor-dependent.
The patch changes the error handling so that the reply says there are
invalid fields but still attempts to set fields that are in range
including PortInfo:PortPhysicalState.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
According to IBTA vol. 1, C11-30.1.1, a notification callback is
invoked if the CQ is armed for the next solicited completion event or
an error completion. The error case wasn't being generated correctly.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support to recognize another board variation named QME7362.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The receive header queue sizes need to modified for performance
tuning. Three module parameters are added to support this.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_create_send_mad() can return ERR_PTR(-ENOMEM) here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_create_send_mad() can return ERR_PTR(-ENOMEM) here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mlx4_ib_free_cq_buf() should not be called under spin_lock_irq() since
it calls dma_free_coherent(), which needs irqs enabled. Fix this by
deferring the free to outside the locked region.
This was found due to the
WARN_ON(irqs_disabled());
in swiotlb_free_coherent().
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
As a first step in moving from LRO to GRO, revert commit af40da894e
("IPoIB: add LRO support"). Also eliminate the ethtool set_flags
callback which isn't needed anymore. Finally, we need to include
<linux/sched.h> directly to get the declaration of restart_syscall()
(which used to be included implicitly through <linux/inet_lro.h>).
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Re-initializing the wait object in rdma_init()/rdma_fini() causes a
timing window which can lead to a deadlock during close. Once this
deadlock hits, all RDMA activity over the T4 device will be stuck.
There's no need to re-init the wait object, so remove it.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This removes unused code found by running 'make namespacecheck';
compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Put the variables accessed together in the hot-path into common
cachelines, and separate them by RW vs RO to avoid false dirtying.
We keep a local copy of the lkey and rkey in the target to avoid
traversing pointers (and associated cache lines) to find them.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David Dillow <dillowda@ornl.gov>
We don't need protection against the SCSI stack, so use our own lock to
allow parallel progress on separate CPUs.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
[ broken out and small cleanups by David Dillow ]
Signed-off-by: David Dillow <dillowda@ornl.gov>
We only need the lock to cover list and credit manipulations, so push
those into srp_remove_req() and update the call chains.
We reorder the request removal and command completion in
srp_process_rsp() to avoid the SCSI mid-layer sending another command
before we've released our request and added any credits returned by the
target. This prevents us from returning HOST_BUSY unneccesarily.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
[ broken out, small cleanups, and modified to avoid potential extraneous
HOST_BUSY returns by David Dillow ]
Signed-off-by: David Dillow <dillowda@ornl.gov>
We only need locks to protect our lists and number of credits available.
By pre-consuming the credit for the request, we can reduce our lock
coverage to just those areas. If we don't actually send the request,
we'll need to put the credit back into the pool.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
[ broken out and small cleanups by David Dillow ]
Signed-off-by: David Dillow <dillowda@ornl.gov>
We use req->scmnd != NULL to indicate an active request, so there's no
need to keep a separate list for them. We can afford the array iteration
during error handling, and dropping it gives us one less item that needs
lock protection.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
[ broken out and small cleanups by David Dillow ]
Signed-off-by: David Dillow <dillowda@ornl.gov>
dget_locked was a shortcut to avoid the lazy lru manipulation when we already
held dcache_lock (lru manipulation was relatively cheap at that point).
However, how that the lru lock is an innermost one, we never hold it at any
caller, so the lock cost can now be avoided. We already have well working lazy
dcache LRU, so it should be fine to defer LRU manipulations to scan time.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Make d_count non-atomic and protect it with d_lock. This allows us to ensure a
0 refcount dentry remains 0 without dcache_lock. It is also fairly natural when
we start protecting many other dentry members with d_lock.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Only one CPU at a time will own an RX IU, so using the address of the IU
as the work request cookie allows us to avoid taking a lock. We can
similarly prepare the TX path for lockless posting by moving the free TX
IUs to a list. This also removes the requirement that the queue sizes be
a power of 2.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
[ broken out, small cleanups, and modified to avoid needing an extra field
in the IU by David Dillow]
Signed-off-by: David Dillow <dillowda@ornl.gov>
We can only have one task management comment outstanding, so move the
completion and status to the target port. This allows us to handle
resets of a LUN without a corresponding request having been sent.
Meanwhile, we don't need to play games with host_scribble, just use it
as the pointer it is.
This fixes a crash when we issue a bus reset using sg_reset.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=13893
Reported-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David Dillow <dillowda@ornl.gov>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
In ib_uverbs_poll_cq() code there is a potential integer overflow if
userspace passes in a large cmd.ne. The calls to kmalloc() would
allocate smaller buffers than intended, leading to memory corruption.
There iss also an information leak if resp wasn't all used.
Unprivileged userspace may call this function, although only if an
RDMA device that uses this function is present.
Fix this by copying CQ entries one at a time, which avoids the
allocation entirely, and also by moving this copying into a function
that makes sure to initialize all memory copied to userspace.
Special thanks to Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
for his help and advice.
Cc: <stable@kernel.org>
Signed-off-by: Dan Carpenter <error27@gmail.com>
[ Monkey around with things a bit to avoid bad code generation by gcc
when designated initializers are used. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB: Fix information leak in marshalling code
IB/pack: Remove some unused code added by the IBoE patches
IB/mlx4: Fix IBoE link state
IB/mlx4: Fix IBoE reported link rate
mlx4_core: Workaround firmware bug in query dev cap
IB/mlx4: Fix memory ordering of VLAN insertion control bits
MAINTAINERS: Update NetEffect entry
ib_ucm_init_qp_attr() and ucma_init_qp_attr() pass struct ib_uverbs_qp_attr
with reserved, qp_state, {ah_attr,alt_ah_attr}{reserved,->grh.reserved}
fields uninitialized to copy_to_user(). This leads to leaking of
contents of kernel stack memory to userspace.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use netif_running() and netif_carrier_ok() to report link state,
exactly as is done to report Ethernet link state in sysfs.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The link rate is the product of the link speed in the link width. For
Etherent ports the rate is 10G, so we use 1 for the width and 4 for
speed to get the correct rate.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We must fully update the control segment before marking it as valid,
so that hardware doesn't start executing it before we're ready.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Move VLAN control bit setting to before wmb(). - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
dev_base_lock is the legacy way to lock the device list, and is planned
to disappear. (writers hold RTNL, readers hold RCU lock)
Convert rdma_translate_ip() and update_ipv6_gids() to RCU locking.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Only include the header linux/mutex.h once inside
drivers/infiniband/hw/cxgb4/iw_cxgb4.h
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It seems idev field in struct rtable has no special purpose, but adding
extra atomic ops.
We hold refcounts on the device itself (using percpu data, so pretty
cheap in current kernel).
infiniband case is solved using dst.dev instead of idev->dev
Removal of this field means routing without route cache is now using
shared data, percpu data, and only potential contention is a pair of
atomic ops on struct neighbour per forwarded packet.
About 5% speedup on routing test.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (52 commits)
split invalidate_inodes()
fs: skip I_FREEING inodes in writeback_sb_inodes
fs: fold invalidate_list into invalidate_inodes
fs: do not drop inode_lock in dispose_list
fs: inode split IO and LRU lists
fs: switch bdev inode bdi's correctly
fs: fix buffer invalidation in invalidate_list
fsnotify: use dget_parent
smbfs: use dget_parent
exportfs: use dget_parent
fs: use RCU read side protection in d_validate
fs: clean up dentry lru modification
fs: split __shrink_dcache_sb
fs: improve DCACHE_REFERENCED usage
fs: use percpu counter for nr_dentry and nr_dentry_unused
fs: simplify __d_free
fs: take dcache_lock inside __d_path
fs: do not assign default i_ino in new_inode
fs: introduce a per-cpu last_ino allocator
new helper: ihold()
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (63 commits)
IB/qib: clean up properly if pci_set_consistent_dma_mask() fails
IB/qib: Allow driver to load if PCIe AER fails
IB/qib: Fix uninitialized pointer if CONFIG_PCI_MSI not set
IB/qib: Fix extra log level in qib_early_err()
RDMA/cxgb4: Remove unnecessary KERN_<level> use
RDMA/cxgb3: Remove unnecessary KERN_<level> use
IB/core: Add link layer type information to sysfs
IB/mlx4: Add VLAN support for IBoE
IB/core: Add VLAN support for IBoE
IB/mlx4: Add support for IBoE
mlx4_en: Change multicast promiscuous mode to support IBoE
mlx4_core: Update data structures and constants for IBoE
mlx4_core: Allow protocol drivers to find corresponding interfaces
IB/uverbs: Return link layer type to userspace for query port operation
IB/srp: Sync buffer before posting send
IB/srp: Use list_first_entry()
IB/srp: Reduce number of BUSY conditions
IB/srp: Eliminate two forward declarations
IB/mlx4: Signal node desc changes to SM by using FW to generate trap 144
IB: Replace EXTRA_CFLAGS with ccflags-y
...
Use the new {max,min}3 macros to save some cycles and bytes on the stack.
This patch substitutes trivial nested macros with their counterpart.
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Joe Perches <joe@perches.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up properly if pci_set_consistent_dma_mask() fails.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some PCIe root complex chip sets don't support advanced error reporting.
Allow the driver to load OK if pci_enable_pcie_error_reporting() fails.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If CONFIG_PCI_MSI is not set, and a QLE7140 is present, the pointer
"dd" is uninitialized.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Noticed this odd looking thing in dmesg:
ib_qib 0000:02:00.0: <3>ib_qib: Unable to enable pcie error reporting: -5
which is due to a bad use of dev_info.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Instead of always assigning an increasing inode number in new_inode
move the call to assign it into those callers that actually need it.
For now callers that need it is estimated conservatively, that is
the call is added to all filesystems that do not assign an i_ino
by themselves. For a few more filesystems we can avoid assigning
any inode number given that they aren't user visible, and for others
it could be done lazily when an inode number is actually needed,
but that's left for later patches.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Since an IB transport port may use either IB or Ethernet as its link layer,
add the file /sys/class/infiniband/<device>/ports/<port_num>/link_layer to
show the link layer for the port.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch allows IBoE traffic to be encapsulated in 802.1Q tagged
VLAN frames. The VLAN tag is encoded in the GID and derived from it
by a simple computation.
The netdev notifier callback is modified to catch VLAN device
addition/removal and the port's GID table is updated to reflect the
change, so that for each netdevice there is an entry in the GID table.
When the port's GID table is exhausted, GID entries will not be added.
Only children of the main interfaces can add to the GID table; if a
VLAN interface is added on another VLAN interface (e.g. "vconfig add
eth2.6 8"), then that interfaces will not add an entry to the GID
table.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add 802.1q VLAN support to IBoE. The VLAN tag is encoded within the
GID derived from a link local address in the following way:
GID[11] GID[12] contain the VLAN ID when the GID contains a VLAN.
The 3 bits user priority field of the packets are identical to the 3
bits of the SL.
In case of rdma_cm apps, the TOS field is used to generate the SL
field by doing a shift right of 5 bits effectively taking to 3 MS bits
of the TOS field.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for IBoE to mlx4_ib. The bulk of the code is handling the
new address vector fields; mlx4 needs the MAC address of a remote node
to include it in a WQE (for datagrams) or in the QP context (for
connected QPs). Address resolution is done by assuming all unicast
GIDs are either link-local IPv6 addresses.
Multicast group attach/detach needs to update the NIC's multicast
filters; but since attaching a QP to a multicast group can be done
before the QP is bound to a port, for IBoE we need to keep track of
all multicast groups that a QP is attached too before it transitions
from INIT to RTR (since it does not have a port in the INIT state).
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Many things cleaned up and otherwise monkeyed with; hope I didn't
introduce too many bugs. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
srp_send_tsk_mgmt() was missing the proper DMA sync calls before posting
the buffer to the device.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use the list_first_entry() macro in ib_srp instead of open-coding the equivalent,
which makes the source code slightly more descriptive. The list_first_entry()
macro itself was introduced in kernel 2.6.22.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
As proposed by the SRP (draft) standard, ib_srp reserves one ring
element for SRP_TSK_MGMT requests. This patch makes sure that the SCSI
mid-layer never tries to queue more than (SRP request limit) - 1 SCSI
commands to ib_srp. This improves performance for targets whose request
limit is less than or equal to SRP_NORMAL_REQ_SQ_SIZE by reducing the
number of BUSY responses reported by ib_srp to the SCSI mid-layer.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The Node Description cannot be changed via MADs (it is read-only).
Until now, it was changed in the driver via sysfs, and the new Node
Description was simply inserted by the driver into MAD responses
(replacing the description returned by FW).
System startup scripts use the sysfs interface to change the node
description at driver startup to show the hostname, etc. However, this
has a race condition: the SM could discover the original FW node
description rather than the system-specific description if it queried the
port before the startup scripts finish running.
For mlx4, we fix this with a new FW command (SET_NODE) that allows
passing the new node description to FW. When this command is invoked,
FW sends a trap 144 to the SM. When it gets this trap, the SM can
query the node to obtain the new node description -- thus eliminating
the effects of the race.
This patch simply calls SET_NODE command when a new node description
is entered via sysfs (thus causing trap 144 to be issued by the FW).
We ignore all failures of the SET_NODE command (including those caused
by using a device FW that predates the SET_NODE command), since in
that case things work just as before.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For iWARP connections, the connect request is carried in a TCP payload
on an already established TCP connection. So if the ucma's backlog is
full, the connection request is transmitted and acked at the TCP level
by the time the connect request gets dropped in the ucma. The end
result is the connection gets rejected by the iWARP provider.
Further, a 32 node 256NP OpenMPI job will generate > 128 connect
requests on some ranks.
This patch increases the default max backlog to 1024, and adds a
sysctl variable so the backlog can be adjusted at run time.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use the net device's dev_id field to encode the port number of the pci
device. This can be used to to associate a net device with the pci
device's port. The encoding is: dev_id = port - 1.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
vlan: Calling vlan_hwaccel_do_receive() is always valid.
tproxy: use the interface primary IP address as a default value for --on-ip
tproxy: added IPv6 support to the socket match
cxgb3: function namespace cleanup
tproxy: added IPv6 support to the TPROXY target
tproxy: added IPv6 socket lookup function to nf_tproxy_core
be2net: Changes to use only priority codes allowed by f/w
tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
tproxy: added tproxy sockopt interface in the IPV6 layer
tproxy: added udp6_lib_lookup function
tproxy: added const specifiers to udp lookup functions
tproxy: split off ipv6 defragmentation to a separate module
l2tp: small cleanup
nf_nat: restrict ICMP translation for embedded header
can: mcp251x: fix generation of error frames
can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
can-raw: add msg_flags to distinguish local traffic
9p: client code cleanup
rds: make local functions/variables static
...
Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
This patch adds support for SRP_CRED_REQ to avoid a lockup by targets
that use that mechanism to return credits to the initiator. This
prevents a lockup observed in the field where we would never add the
credits from the SRP_CRED_REQ to our current count, and would therefore
never send another command to the target.
Minimal support for SRP_AER_REQ is also added, as these messages can
also be used to convey additional credits to the initiator.
Based upon extensive debugging and code by Bart Van Assche and a bug
report by Chris Worley.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The transmit ring in ib_srp (srp_target.tx_ring) is currently only used
for allocating requests sent by the initiator to the target. This patch
prepares using that ring for allocation of both requests and responses.
Also, this patch differentiates the uses of SRP_SQ_SIZE, increases the
size of the IB send completion queue by one element and reserves one
transmit ring slot for SRP_TSK_MGMT requests.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
See table 35 in IBA - the header order for RDMA_WRITE_ONLY_WITH_IMMEDIATE
and SEND_LAST_WITH_IMMEDIATE is different: the RDMA_WRITE_ONLY has
a RETH header before the immediate data, so we need a different code path
to extract the immediate data.
I tested this with a userspace app that does RDMA_WRITE with immediate
on a QLE7140.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The flushing of work requests for user QPs is implemented entirely in
the user mode library. The only kernel interaction is to mark the
user QP object indicating it is in error when the QP exits RTS. When
the user QP operations are called by the application (eg: post_send,
post_recv), the QP in error bit is checked and if set, the library
flushes the QP. If, however, the application is not doing IO, but
rather just polling the CQ, it will never get flushed work requests.
This breaks some classes of applications.
This patch adds logic to mark user CQs in error when a QP that is bound
to the CQ is marked in error. The library poll code can then notice
the CQ is in error and flush all the in error QPs bound to that CQ.
Design:
- add 1 extra CQE entry to the CQ memory that will be used to indicate
in error status.
- return the desired CQ memory size that should be mapped by the library
- bump the ABI since the create_cq uverbs response changes.
- detect older libraries and reduce the mmap size accordingly.
(The ABI bump doesn't break old libraries, since they didn't check
the ABI field anyway)
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove the local service t4_pktgl_to_skb() and use cxgb4_pktgl_to_skb()
exported by cxgb4.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Add support for packing IBoE packet headers.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Clean up and fix ib_ud_header_init() a bit. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for IBoE device binding and IP --> GID resolution. Path
resolving and multicast joining are implemented within cma.c by
filling in the responses and running callbacks in the CMA work queue.
IP --> GID resolution always yields IPv6 link local addresses; remote
GIDs are derived from the destination MAC address of the remote port.
Multicast GIDs are always mapped to multicast MACs as is done in IPv6.
(IPv4 multicast is enabled by translating IPv4 multicast addresses to
IPv6 multicast as described in
<http://www.mail-archive.com/ipng@sunroof.eng.sun.com/msg02134.html>.)
Some helper functions are added to ib_addr.h.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since IBoE is using Ethernet as its link layer, there is no central
management entity so there is need for QP0. QP1 is still needed since
it handles communications between CM agents. This patch will skip QP0
and create only QP1 for IBoE ports.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
IPoIB is IP-over-Infiniband link layer. In the case of IBoE, the link
layer is Ethernet and IP can work directly over Ethernet, so disable
IPoIB for non-IB_LINK_LAYER_INFINIBAND ports.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We tried very hard to remove all possible dev_hold()/dev_put() pairs in
network stack, using RCU conversions.
There is still an unavoidable device refcount change for every dst we
create/destroy, and this can slow down some workloads (routers or some
app servers, mmap af_packet)
We can switch to a percpu refcount implementation, now dynamic per_cpu
infrastructure is mature. On a 64 cpus machine, this consumes 256 bytes
per device.
On x86, dev_hold(dev) code :
before
lock incl 0x280(%ebx)
after:
movl 0x260(%ebx),%eax
incl fs:(%eax)
Stress bench :
(Sending 160.000.000 UDP frames,
IP route cache disabled, dual E5540 @2.53GHz,
32bit kernel, FIB_TRIE)
Before:
real 1m1.662s
user 0m14.373s
sys 12m55.960s
After:
real 0m51.179s
user 0m15.329s
sys 10m15.942s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A process can get stuck in an uninterruptible wait in the
kernel while destroying a cm_id when iw_cm_connect() fails:
For example, When creation of a PD fails but the user continues with
an attempt to connect to the server without checking the return value,
in iw_cm_connect() a NULL qp is found so the call fails. However the
IWCM_F_CONNECT_WAIT bit is not cleared. destroy_cm_id() then waits
forever for IWCM_F_CONNECT_WAIT to be cleared.
The same problem exists on the passive side with the accept call.
Fix this by clearing the bit and waking up any waiters in the
appropriate spots.
Signed-off-by: Animesh Trivedi <atr@zurich.ibm.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We can replace our equivalent open-coded version.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix the limit on the size of max fast registration WRs that can be
posted to match hardware capabilities.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This lets the bonding driver to detect when an interface goes down.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
With commit cd6860eb ("RDMA/nes: Fix hangs on ifdown") we no longer
remove nes interfaces on ifdown. On nes_query_port(), add an
additional check of the netdev queue and report IB_PORT_DOWN if the
queue is not running.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
the eHCA driver registers a MR for all of kernel memory, but makes the
assumption that valid memory exists at KERNELBASE. This assumption
may not be true in the case of a relocatable kernel, so use KERNELBASE
+ PHYSICAL_START to get the true beginning of usable kernel memory.
cc: Joachim Fenkes <fenkes@de.ibm.com>
cc: Christoph Raisch <raisch@de.ibm.com>
cc: Hoan-Ham Hguyen <hnguyen@de.ibm.com>
Signed-off-by: Sonny Rao <sonnyrao@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Get rid of init_MUTEX[_LOCKED]() and use sema_init() instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Just a small cleanup. The "passive_state" variable isn't used any
more after commit dae58728dc ("RDMA/nes: Fix double CLOSE event
indication crash")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
IGMP processing is broken because the IPOIB does not set the
skb->pkt_type the right way for multicast traffic. All incoming
packets are set to PACKET_HOST which means that igmp_recv() will
ignore the IGMP broadcasts/multicasts.
This in turn means that the IGMP timers are firing and are sending
information about multicast subscriptions unnecessarily. In a large
private network this can cause traffic spikes.
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Remove dsgl support - doesn't work in T4.
- Wrap the immediate PBL as needed when building it in the wr.
- Adjust max pbl depth allowed based on ulptx alignment requirements.
- Bump the slots per SQ to 5 to allow up to 128MB fast registers.
- Advertise fastreg support by default.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the connection setup/teardown paths to the workq thread removing
spin lock/irq disable requirements for these paths. This allows calls
down to the LLD for EP and QP state transition actions to be atomic
with respect to processing CPL messages coming up from the HW.
Namely, calls to rdma_init() and rdma_fini() can now be called with
the mutex held avoiding many race conditions with the abort path.
The QP spinlock is still used but only to manipulate the qp state. This
allows the fastpaths, poll, post_send, and pos_recv, to run in the
irq context.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
T4 support on-chip SQs to reduce latency. This patch adds support for
this in iw_cxgb4:
- Manage ocqp memory like other adapter mem resources.
- Allocate user mode SQs from ocqp mem if available.
- Map ocqp mem to user process using write combining.
- Map PCIE_MA_SYNC reg to user process.
Bump uverbs ABI.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add "stags" debugfs file. This is useful for examining the TPTE and
PBL entries in adapter memory. It allows scripts to dump just the
active entries.
Also clean up the "qps" file handlers and shared common code.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This helps debug cases where HW resources are depleted.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
T4 FW sends up CPL_RDMA_TERMINATE to indicate a peer TERM. This
triggers the QP moving to TERMINATE state.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
T4 incorrectly inserts TERM CQEs into the CQ. Silently ignore them.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The cxgb4_*_send() functions return NET_XMIT_ values, which are
positive integers or negative errno values. So don't treat positive
return values as an error.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The HW design requires zeroing any pad in SGLs.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In c4iw_modify_qp() error path, only use qhp->ep if ep is not already set.
Otherwise qhp->ep can be NULL and we crash.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix:
drivers/infiniband/hw/nes/nes_verbs.c: In function 'nes_alloc_fast_reg_page_list':
drivers/infiniband/hw/nes/nes_verbs.c:477: warning: cast to pointer from integer of different size
drivers/infiniband/hw/nes/nes_verbs.c: In function 'nes_post_send':
drivers/infiniband/hw/nes/nes_verbs.c:3486: warning: cast to pointer from integer of different size
drivers/infiniband/hw/nes/nes_verbs.c:3486: warning: cast to pointer from integer of different size
by printing u64 quantities by casting to unsigned long and long and
using %llx, rather than casting to void* and using %p.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch allows ports to have different link layers:
IB_LINK_LAYER_INFINIBAND or IB_LINK_LAYER_ETHERNET. This is required
for adding IBoE (InfiniBand-over-Ethernet, aka RoCE) support. For
devices that do not provide an implementation for querying the link
layer property of a port, we return a default value based on the
transport: RMA_TRANSPORT_IB nodes will return IB_LINK_LAYER_INFINIBAND
and RDMA_TRANSPORT_IWARP nodes will return IB_LINK_LAYER_ETHERNET.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix:
drivers/infiniband/hw/cxgb4/qp.c: In function ‘create_qp’:
drivers/infiniband/hw/cxgb4/qp.c:147: warning: cast from pointer to integer of different size
drivers/infiniband/hw/cxgb4/qp.c: In function ‘rdma_fini’:
drivers/infiniband/hw/cxgb4/qp.c:988: warning: cast from pointer to integer of different size
drivers/infiniband/hw/cxgb4/qp.c: In function ‘rdma_init’:
drivers/infiniband/hw/cxgb4/qp.c:1063: warning: cast from pointer to integer of different size
drivers/infiniband/hw/cxgb4/mem.c: In function ‘write_adapter_mem’:
drivers/infiniband/hw/cxgb4/mem.c:74: warning: cast from pointer to integer of different size
drivers/infiniband/hw/cxgb4/cq.c: In function ‘destroy_cq’:
drivers/infiniband/hw/cxgb4/cq.c:58: warning: cast from pointer to integer of different size
drivers/infiniband/hw/cxgb4/cq.c: In function ‘create_cq’:
drivers/infiniband/hw/cxgb4/cq.c:135: warning: cast from pointer to integer of different size
drivers/infiniband/hw/cxgb4/cm.c: In function ‘fw6_msg’:
drivers/infiniband/hw/cxgb4/cm.c:2326: warning: cast to pointer from integer of different size
by casting pointers to unsigned long instead of u64.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The HW by default has RX coalescing on. For iWARP connections, this
causes a 100ms delay in connection establishement due to the ingress
MPA Start message being stalled in HW. So explicitly turn RX
coalescing off when setting up iWARP connections.
This was causing very bad performance for NP64 gather operations using
Open MPI, due to the way it sets up connections on larger jobs.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Changing state to CLOSING when FIN is received causes A0 cards to
hang. Fix this by checking for A0 cards in FIN handling.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the driver receives an AE for FIN received, it closes the
connection without changing the state of the connection in the
hardware to closing. By changing the state to closing, hardware will
do a normal close sequence.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During a stress testing in a large cluster, multiple close event are
detected and BUG() is hit in the iWARP core. The cause is that the
active node gave up while waiting for an MPA response from the peer
and tried to close the connection by sending RST. The passive node
driver receives the RST but is waiting for MPA response from the user.
When the MPA accept is received, the driver offloads the connection
and sends a CLOSE event. The driver gets an AE indicating RESET
received and also sends a CLOSE event, hitting a BUG().
Fix this by correcting RESET handling and sending CLOSE events.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Setting TX pause param writes to the wrong register location causing
the adapter to hang. Correct the define used to write the reigster.
Addresses: https://bugs.openfabrics.org/show_bug.cgi?id=2116
Reported-by: Shiri Franchi <shirif@voltaire.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The max depth supported by T3 is 64K entries. This fixes a bug
introduced in commit 9918b28d ("RDMA/cxgb3: Increase the max CQ
depth") that causes stalls and possibly crashes in large MPI clusters.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (42 commits)
IB/qib: Add missing <linux/slab.h> include
IB/ehca: Drop unnecessary NULL test
RDMA/nes: Fix confusing if statement indentation
IB/ehca: Init irq tasklet before irq can happen
RDMA/nes: Fix misindented code
RDMA/nes: Fix showing wqm_quanta
RDMA/nes: Get rid of "set but not used" variables
RDMA/nes: Read firmware version from correct place
IB/srp: Export req_lim via sysfs
IB/srp: Make receive buffer handling more robust
IB/srp: Use print_hex_dump()
IB: Rename RAW_ETY to RAW_ETHERTYPE
RDMA/nes: Fix two sparse warnings
RDMA/cxgb3: Make needlessly global iwch_l2t_send() static
IB/iser: Make needlessly global iser_alloc_rx_descriptors() static
RDMA/cxgb4: Add timeouts when waiting for FW responses
IB/qib: Fix race between qib_error_qp() and receive packet processing
IB/qib: Limit the number of packets processed per interrupt
IB/qib: Allow writes to the diag_counters to be able to clear them
IB/qib: Set cfgctxts to number of CPUs by default
...
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
Steve Wise
Roland Dreier
Ira Weiny
Paul Gortmaker
Linus Torvalds
Nir Muchtar
Benjamin Herrenschmidt
Sergei Shtylyov
David S. Miller
Mitko Haralanov
Roel Kluin
Hefty, Sean
David Decotigny
Lucas De Marchi
Nishanth Aravamudan
Michał Mirosław
Yevgeny Petrilin
David Dillow
Michael Heinz
Huang Ying
Nicolas Kaiser
Mike Christie
Mike Marciniszyn
Jiri Pirko
Maciej Sosnowski
Tejun Heo
Ralf Thielow
David Rientjes
Roland Dreier
Bart Van Assche
Aleksey Senin
Joe Perches
John L. Burr
Mike Marciniszyn
Dan Carpenter
Vladimir Sokolovsky
Or Gerlitz
Stephen Hemminger
Nick Piggin
Jiri Kosina
Vasiliy Kulikov
Eli Cohen
Eric Dumazet
Arnd Bergmann
Jeff Garzik
Jesper Juhl
Uwe Kleine-König
Al Viro
Hagen Paul Pfeifer
Jason Gunthorpe
Ralph Campbell
Christoph Hellwig
Eli Cohen
Jack Morgenstein
matt mooney
Justin P. Mattock
Randy Dunlap
Animesh K Trivedi
Chien Tung
Sonny Rao
Thomas Gleixner
Christoph Lameter
Faisal Latif
Grant Likely