If the RTNL is held when we invoke flush_scheduled_work() we could
deadlock. One such case is linkwatch, it is a work struct which tries
to grab the RTNL semaphore.
The most common case are net driver ->stop() methods. The
simplest conversion is to instead use cancel_{delayed_}work_sync()
explicitly on the various work struct the driver uses.
This is an OK transformation because these work structs are doing
things like resetting the chip, restarting link negotiation, and so
forth. And if we're bringing down the device, we're about to turn the
chip off and reset it anways. So if we cancel a pending work event,
that's fine here.
Some drivers were working around this deadlock by using a msleep()
polling loop of some sort, and those cases are converted to instead
use cancel_{delayed_}work_sync() as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of assigning values for the struct cpu_reg's at runtime,
we already know these values at compile time. Therefore, we can use
designated initializers, to initialize these structures and not have
to incur this assignment cost at run-time.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make the bnx2 code more consistent, all instances of
RX_COPY_THRESH have been changed to BNX2_RX_COPY_THRESH.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_offset field is set to a constant value and initialized
only once. By replacing all references to the rx_offset field,
we can eliminate rx_offset from the bnx2 structure. This will
save 4 bytes for every bnx2 instance.
[Added parentheses to the definition of BNX2_RX_OFFSET, as noted
by Ben Hutchings.]
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PCI recovery functions to the driver. The initial pci state is
also saved so the the MSI state can be restored during PCI recovery.
Signed-off-by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Gospodarek <andy@greyhouse.net> found that netconsole would
panic when resetting bnx2 devices.
>From Andy:
"The issue is the bnx2_set_link in bnx2_init_nic will print a link-status
message before we are fully initialized and ready to start polling.
Polling is currently disabled in this state, but since the
__LINK_STATE_RX_SCHED is overloaded to not only try and disable polling
but also to make the system aware there is something waiting to be
polled, we really have to fix this in drivers.
The problematic call is the one to netif_rx_complete as it tries to
remove an entry from the poll_list when there isn't one."
While this netconsole problem should be fixed separately, we really
should not reset the PHY when changing ring sizes, MTU, or other
similar settings. The PHY reset causes several seconds of unnecessary
link disruptions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new RV2P firmware fixes 2 issues:
1. The jumbo rx buffer page size is now configurable and set to the
proper PAGE_SIZE. Before, it was assumed to be always 4K.
2. Driver sometimes would crash when receiving jumbo packets mixed
with firmware management packets. This was caused by the old
firmware DMA'ing to the wrong address.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should zero out the context memory for 5709 before each reset. When
we resume after suspend for example, the memory may not be zero and the
chip may not function correctly.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register BNX2_CTX_STATUS (0x1004) should be skipped on 5709 as it
contains reserved bits.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some remote PHY blade systems, the driver receives no initial link
interrupt. As a result, the GMII/MII MAC mode does not get setup properly.
To fix this problem, we add an initial poll of the link state after chip
reset.
With this change, the setting of the initial carrier state in the init
code can be eliminated.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2_set_remote_link() should be called under bp->phy_lock to protect
against concurrent polling and interrupt calls. This change is needed
by the next patch which will add one initial poll of the remote PHY
link status.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of some board issues, we need to disable parallel detect on
an HP blade. Without this patch, the link state can become stuck
when it goes into parallel detect mode.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patches to workaround the 5706S on an HP blade were not
sufficient. The link state still does not change properly in some
cases. This patch adds polling to make it completely reliable.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-3.4.4 on powerpc:
drivers/net/bnx2.c:67: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were checking for the ASYM_PAUSE bit for 1000Base-X twice instead
checking for both the 1000Base-X bit and the 10/100/1000Base-T bit.
The purpose of the logic is to tell the firmware that ASYM_PAUSE is
set on either the Serdes or Copper interface.
Problem was discovered by Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the programmable high/low water marks in 5709 for
802.3 flow control.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CTX_WR macro is unnecessary and obfuscates the code.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The REG_WR_IND/REG_RD_IND macros are unnecessary and obfuscate the
code. Many callers to these macros read and write shared memory from
the bp->shmem_base, so we add 2 similar functions that automatically
add the shared memory base.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the tx coalescing setup code independent of the MSIX vector.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Correct the MII expansion serdes control register definition.
2. Check an additional RUDI_INVALID bit when determining 5706S link.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix "bp->phy_flags" names with BNX2_PHY_FLAG_* for consistency.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some blade systems using the 5706 serdes, the hardware sometimes
does not properly generate link down interrupts. We add a workaround
in the driver's timer to force a link-down when some PHY registers
report loss of SYNC.
The parallel detect logic is cleaned up slightly to better integrate
the workaround.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is more correct to get the status block from the bnx2_napi struct
instead of the bnx2 struct. It happens that they are the same in this
case because we are using the first MSIX vector.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip has problem running in this mode and needs to be disabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change bnx2_init_napi() to void.
Warning was noted by DaveM.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable new tx ring and add new MSIX handler and NAPI poll function
for the new tx ring. Enable MSIX when the hardware supports it.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To separate TX IRQs into a different MSIX vector, we need to
support a new tx ring. The original tx ring will still be used
when not using MSIX.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change bnx2_napi struct into an array and add code to manage multiple
IRQs. MSIX hardware structures and new registers are also added.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx related fields used in NAPI polling are moved from the main
bnx2 struct to the bnx2_napi struct.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx related fields used in NAPI polling are moved from the main
bnx2 struct to the bnx2_napi struct.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a bnx2_napi structure that will hold a napi_struct and
other fields to handle NAPI polling for the napi_struct. Various tx
and rx indexes and status block pointers will be moved from the main
bnx2 structure to this bnx2_napi structure.
Most NAPI path functions are modified to be passed this bnx2_napi
struct pointer.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a table to keep track of multiple IRQs and restructure the IRQ
request and free functions so that they can be easily expanded to
handle multiple IRQs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the code cleaner and easier to support different tx rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the MTU requires more than 1 page for the SKB, enable the page ring
and calculate the size of the page ring. This will guarantee order-0
allocation regardless of the MTU size.
Fixup loopback test packet size so that we don't deal with the pages
during loopback test.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add function to reuse a page in case of allocation or other errors.
Add code to construct the completed SKB with the additional data in
the pages.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new fields to keep track of the pages and the page rings.
Add functions to allocate and free pages.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the common functions that will be used to initialize the
normal RX rings and the page rings.
Change the copybreak constant RX_COPY_THRESH to 128. This same
constant will be used for the max. size of the linear SKB when pages
are used. Copybreak will be turned off when pages are used.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new function to handle new SKB allocation and to prepare the
completed SKB. This makes it easier to add support for non-linear
SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the various ring constants to make the code cleaner.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets can be left in the RX ring if the NAPI budget is reached.
This is caused by storing the latest rx index at the beginning of
bnx2_rx_int(). We may not process all the work up to this index
if the budget is reached and so some packets in the RX ring may rot
when we later check for more work using this stored rx index.
The fix is to not store this latest hw index and only store the
processed rx index. We use a new function bnx2_get_hw_rx_cons()
to fetch the latest hw rx index.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove asm/bitops.h includes
including asm/bitops directly may cause compile errors. don't include it
and include linux/bitops instead. next patch will deny including asm header
directly.
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (51 commits)
[IPV6]: Fix again the fl6_sock_lookup() fixed locking
[NETFILTER]: nf_conntrack_tcp: fix connection reopening fix
[IPV6]: Fix race in ipv6_flowlabel_opt() when inserting two labels
[IPV6]: Lost locking in fl6_sock_lookup
[IPV6]: Lost locking when inserting a flowlabel in ipv6_fl_list
[NETFILTER]: xt_sctp: fix mistake to pass a pointer where array is required
[NET]: Fix OOPS due to missing check in dev_parse_header().
[TCP]: Remove lost_retrans zero seqno special cases
[NET]: fix carrier-on bug?
[NET]: Fix uninitialised variable in ip_frag_reasm()
[IPSEC]: Rename mode to outer_mode and add inner_mode
[IPSEC]: Disallow combinations of RO and AH/ESP/IPCOMP
[IPSEC]: Use the top IPv4 route's peer instead of the bottom
[IPSEC]: Store afinfo pointer in xfrm_mode
[IPSEC]: Add missing BEET checks
[IPSEC]: Move type and mode map into xfrm_state.c
[IPSEC]: Fix length check in xfrm_parse_spi
[IPSEC]: Move ip_summed zapping out of xfrm6_rcv_spi
[IPSEC]: Get nexthdr from caller in xfrm6_rcv_spi
[IPSEC]: Move tunnel parsing for IPv4 out of xfrm4_input
...
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The bug is in the code in bnx2_set_power_state() that assumes copper
devices when setting up WoL. This is no longer true after adding WoL
support for Serdes devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to read and store sblk->status_idx before checking for more work.
The status idx is later written back to the hardware when enabling
interrupts to acknowledge how much work has been processed. If the
order is reversed, we can end up acknowledging work we haven't
processed.
When completing bnx2_poll(), we should always break out of the while
loop and return work_done instead of returning 0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for the list handling in net_rx_action() to be
correct, drivers must follow certain rules as stated by
this comment in net_rx_action():
/* Drivers must not modify the NAPI state if they
* consume the entire weight. In such cases this code
* still "owns" the NAPI instance and therefore can
* move the instance around on the list at-will.
*/
A few drivers do not do this because they mix the budget checks
with reading hardware state, resulting in crashes like the one
reported by takano@axe-inc.co.jp.
BNX2 and TG3 are taken care of here, SKY2 fix is from Stephen
Hemminger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the default WoL setting to match the NVRAM's setting. It
always defaulted to WoL disabled before and caused a lot of confusion
for users.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The remote PHY media type and link status can change between
->probe() and ->open(). For correct operation, we need to get the
new status again during ->open().
The ethtool link test and loopback test are also fixed to work with
remote PHY. PHY loopback is simply skipped when remote PHY is
present.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a follow up to the patches from Denys Vlasenkos
<vda.linux@googlemail.com> to further optimize firmware loading.
1. In bnx2_init_cpus(), we allocate memory for decompression once
and use it repeatedly instead of doing this for every firmware image.
2. We eliminate the BSS and SBSS firmware sections in bnx2_fw*.h since
these are always zeros.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies gzip unpacking code in bnx2 driver so that
it does not depend on bnx2 internals. I will move this code
out of the driver and into zlib in follow-on patch.
It can be useful in other drivers which need to store firmwares
or any other relatively big binary blobs - fonts, cursor bitmaps,
whatever.
Patch is run tested by Michael Chan (driver author).
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the operations
get-tx-csum
get-sg
get-tso
get-ufo
the default ethtool_op_xxx behavior is fine for all drivers, so we
permit op==NULL to imply the default behavior.
This provides a more uniform behavior across all drivers, eliminating
ethtool(8) "ioctl not supported" errors on older drivers that had
not been updated for the latest sub-ioctls.
The ethtool_op_xxx() functions are left exported, in case anyone
wishes to call them directly from a driver-private implementation --
a not-uncommon case. Should an ethtool_op_xxx() helper remain unused
for a while, except by net/core/ethtool.c, we can un-export it at a
later date.
[ Resolved conflicts with set/get value ethtool patch... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.
In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.
The signature of the ->poll() call back goes from:
int foo_poll(struct net_device *dev, int *budget)
to
int foo_poll(struct napi_struct *napi, int budget)
The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract). The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.
The napi_struct is to be embedded in the device driver private data
structures.
Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler. Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.
With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.
Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.
[ Ported to current tree and all drivers converted. Integrated
Stephen's follow-on kerneldoc additions, and restored poll_list
handling to the old style to fix mutual exclusion issues. -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the DIS_EARLY_DAC PHY workaround for 5709 A1. Without it, link
sometimes does not come up.
Update version to 1.6.5.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add comment to explain why we cannot read back after chip reset
before delaying.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2.c (incorrectly) sets current->state directly to
TASK_UNINTERRUPTIBLE, without going through set_task_state(). However
all the code wants to do is an msleep so just make it do that instead...
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device would not resume properly if it was shutdown before the system
was suspended. In such scenario where the netif_running state is 0,
bnx2_suspend() would not save the PCI state and so the memory enable bit
and bus master enable bit would be lost.
We fix this by always saving and restoring the PCI state in
bnx2_suspend() and bnx2_resume() regardless of netif_running() state.
Update version to 1.6.4.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers implement ethtool get_perm_addr the same way -- by calling
the generic function. So we can inline the generic function into the
caller and avoid going through the drivers.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change all stats related magic numbers to constants.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The management firmware may still be loading during bnx2_init_one()
because of the D3hot -> D0 transition and the firmware version may
not be available without waiting a bit.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NVRAM interface is slightly modified on the 5709. To properly
support it, we need to change the buffered flag in the flash data
structure into multiple flags to indicate buffered operation, address
translation, and the use of write enable (WREN). The 5709 flash
only requires the buffered operation bit to be set.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool utility function to set or clear IPV6_CSUM feature flag.
Modify tg3.c and bnx2.c to use this function when doing ethtool -K
to change tx checksum.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 963bd949b1. The
driver _does_ need the networking header files;
CC [M] drivers/net/bnx2.o
drivers/net/bnx2.c: In function 'bnx2_start_xmit':
drivers/net/bnx2.c:5177: warning: implicit declaration of function 'tcp_optlen'
drivers/net/bnx2.c:5181: error: invalid application of 'sizeof' to incomplete type 'struct ipv6hdr'
drivers/net/bnx2.c:5202: error: invalid application of 'sizeof' to incomplete type 'struct tcphdr'
drivers/net/bnx2.c:5207: warning: implicit declaration of function 'tcp_hdr'
drivers/net/bnx2.c:5207: error: invalid type argument of '->'
make[2]: *** [drivers/net/bnx2.o] Error 1
make[1]: *** [drivers/net] Error 2
make: *** [drivers] Error 2
Cc: Ilpo Jävinen <ilpo.jarvinen@helsinki.fi>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Got bored to always recompile it for no reason.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
In addition to the periodic heartbeat, we're adding a heartbeat
request interrupt when the heartbeat is late. This is needed during
netpoll where the timer is not available. -rt kernels will also
benefit since the timer is not as accurate.
[ We discussed this patch last time and we decided that the -rt
kernel problem alone did not justify this patch. I think the
netpoll problem makes this patch necessary. ]
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spurious interrupts are often encountered especially on systems
using the 8259 PIC mode. This is because the I/O write to deassert
the interrupt is posted and won't get to the chip immediately. As
a result, the IRQ may remain asserted after the IRQ handler exits,
causing spurious interrupts.
Add read back to flush the I/O write to deassert the IRQ immediately.
We also store the last_status_idx immediately in the IRQ handler to
help detect whether the interrupt is ours or not when the IRQ is
entered again before ->poll gets called.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the link up dmesg to report remote copper or Serdes link.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the driver's ethtool_ops->get_settings and set_settings
functions to support remote PHY. Users control the remote copper
PHY settings by specifying link settings for the tp (twisted pair)
port.
The nway_reset function is also modified to support remote PHY.
mii-tool operations are not supported on remote PHY and we will
return -EOPNOTSUPP.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In blade servers, the Serdes PHY in 5708S can control the remote
copper PHY through autonegotiation on the backplane. This patch adds
the logic to interface with the firmware to control the remote PHY
autonegotiation and to handle remote PHY link events.
When remote PHY is present, the 5708S Serdes device practically
becomes a copper device with full control over the 1000Base-T
link settings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put existing code to setup the default link settings in this new
function. This makes it easier to support the remote PHY feature in
the next few patches.
Also change ETHTOOL_ALL_FIBRE_SPEED to include 2500Mbps if supported.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing model for checksum offload does not correctly handle
devices that can offload IPV4 and IPV6 only. The NETIF_F_HW_CSUM flag
implies device can do any arbitrary protocol.
This patch:
* adds NETIF_F_IPV6_CSUM for those devices
* fixes bnx2 and tg3 devices that need it
* add NETIF_F_IPV6_CSUM to ipv6 output (incl GSO)
* fixes assumptions about NETIF_F_ALL_CSUM in nat
* adjusts bridge union of checksumming computation
Signed-off-by: David S. Miller <davem@davemloft.net>
Update to version 1.5.11.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistics block DMA on 5708 can be messed up occasionally on the
average of about once per hour. If the user is reading the counters
within one second after the corruption, the counters will be all
messed up. One second later, the counters will be ok again until the
next corruption occurs.
The workaround is to disable the periodic statistics DMA. Instead,
we manually trigger the DMA once a second in bnx2_timer(). This
manual trigger of the DMA avoids the problem.
As a consequence, we can only allow 0 or 1 second settings for
ethtool -C statistics block.
Thanks to Jean-Daniel Pauget <jd@disjunkt.com> and
CaT <cat@zip.com.au> for reporting this rare problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing code to enable DMA on 5709 A1. The bit is a no-op on A0
and therefore can be set on all 5709 chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller
Michael Chan
Benjamin Li
Wendy Xiong
Harvey Harrison
Andrew Morton
Al Viro
Al Viro
Jiri Slaby
Linus Torvalds
Joe Perches
David S. Miller
Denys Vlasenko
Jeff Garzik
Denis Cheng
Ralf Baechle
Stephen Hemminger
Arjan van de Ven
Matthew Wilcox
Auke Kok
Ilpo Järvinen