Commit Graph

113 Commits

Author SHA1 Message Date
Taniya Das 2849dd8bc7 cpufreq: qcom-hw: Add support for QCOM cpufreq HW driver
The CPUfreq HW present in some QCOM chipsets offloads the steps necessary
for changing the frequency of CPUs. The driver implements the cpufreq
driver interface for this hardware engine.

Signed-off-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-12-18 23:43:09 +01:00
Sudeep Holla f174e49e49 cpufreq: remove unused arm_big_little_dt driver
Most of the ARM platforms used cpufreq-dt driver irrespective of
whether it's big-little(HMP) or SMP system. This arm_big_little_dt is
not used actively at all.

So let's remove the driver, so that it need not be maintained.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-10-25 18:39:02 +02:00
Krzysztof Kozlowski a443c1fc10 cpufreq: exynos: Remove support for Exynos5440
The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
2018-07-17 19:55:51 +02:00
Ilia Lin 46e2856b8e cpufreq: Add Kryo CPU scaling driver
In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors,
the CPU frequency subset and voltage value of each OPP varies
based on the silicon variant in use. Qualcomm Process Voltage Scaling Tables
defines the voltage and frequency value based on the msm-id in SMEM
and speedbin blown in the efuse combination.
The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
to provide the OPP framework with required information.
This is used to determine the voltage and frequency value for each OPP of
operating-points-v2 table when it is parsed by the OPP framework.

Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-05-30 12:53:11 +02:00
Linus Torvalds 38c23685b2 ARM: SoC driver updates for 4.17
The main addition this time around is the new ARM "SCMI" framework,
 which is the latest in a series of standards coming from ARM to do power
 management in a platform independent way. This has been through many
 review cycles, and it relies on a rather interesting way of using the
 mailbox subsystem, but in the end I agreed that Sudeep's version was
 the best we could do after all.
 
 Other changes include:
 
 - the ARM CCN driver is moved out of drivers/bus into drivers/perf,
   which makes more sense. Similarly, the performance monitoring
   portion of the CCI driver are moved the same way and cleaned up
   a little more.
 
 - a series of updates to the SCPI framework
 
 - support for the Mediatek mt7623a SoC in drivers/soc
 
 - support for additional NVIDIA Tegra hardware in drivers/soc
 
 - a new reset driver for Socionext Uniphier
 
 - lesser bug fixes in drivers/soc, drivers/tee, drivers/memory, and
   drivers/firmware and drivers/reset across platforms
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJaxiNzAAoJEGCrR//JCVInYhYP/2kPhc5t/kszA1bcklcbO9dY
 eX37Ra/RR4yQ5yeQZVIZ4UkUovxk9PmG2tM4K5oJaTDsz5pPEgavVOOr3sbfj6vb
 4O9auTeysEQlHcbVdNFum0YS2gUY2YD7D12DTRorotLxCqod184ccWXq0XGfIWaY
 l3YRrcL/lPlqmyS3z/GNx9oNygOMUzEfXfIQYICyzHuYiLBUGnkKC1vIb+Hx1TDq
 Cxk++AUqH13Mss24O2A2QQh+oBHj2BybDLLqwcC5PSpsUbFrVCfzG54l43mig32T
 NOxV0Qnml2wAtU4H0QcgtSgwRimHD0YOiX8ssquvDDiqTqM5G+llSTGkEbYe+AUW
 4GIZYoBOwGkfEXS+tyymHe9yfc5h1OLYAeFU1jRm723c7phanuu67rPn35YC8UMK
 zSql10JpkAGNzMikrxxb6wnis951w2UFlzhgZQ6ItA/nRq3l+oEQA0Qiljv965nz
 DVLsD5+gdhK6GBctkzlsD5HFn6GjM8JilnsOVPHD765nKnVBSxKiXRLV228XVug2
 rChF1FhQqLnM54jCMqHZX5fS9SbSgtYswHqIXpVw6GmJkqq/Ly10yGR0vuWD+uyn
 BV7q5AKpGrwm6wZkMM2uZ1VdUtWzn856AbkqrvX/QhmJcX4McuqaLUrC8bSOj1ty
 KeVil0akq3nU+xHl5Ojs
 =Pmsx
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC driver updates from Arnd Bergmann:
 "The main addition this time around is the new ARM "SCMI" framework,
  which is the latest in a series of standards coming from ARM to do
  power management in a platform independent way.

  This has been through many review cycles, and it relies on a rather
  interesting way of using the mailbox subsystem, but in the end I
  agreed that Sudeep's version was the best we could do after all.

  Other changes include:

   - the ARM CCN driver is moved out of drivers/bus into drivers/perf,
     which makes more sense. Similarly, the performance monitoring
     portion of the CCI driver are moved the same way and cleaned up a
     little more.

   - a series of updates to the SCPI framework

   - support for the Mediatek mt7623a SoC in drivers/soc

   - support for additional NVIDIA Tegra hardware in drivers/soc

   - a new reset driver for Socionext Uniphier

   - lesser bug fixes in drivers/soc, drivers/tee, drivers/memory, and
     drivers/firmware and drivers/reset across platforms"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (87 commits)
  reset: uniphier: add ethernet reset control support for PXs3
  reset: stm32mp1: Enable stm32mp1 reset driver
  dt-bindings: reset: add STM32MP1 resets
  reset: uniphier: add Pro4/Pro5/PXs2 audio systems reset control
  reset: imx7: add 'depends on HAS_IOMEM' to fix unmet dependency
  reset: modify the way reset lookup works for board files
  reset: add support for non-DT systems
  clk: scmi: use devm_of_clk_add_hw_provider() API and drop scmi_clocks_remove
  firmware: arm_scmi: prevent accessing rate_discrete uninitialized
  hwmon: (scmi) return -EINVAL when sensor information is unavailable
  amlogic: meson-gx-socinfo: Update soc ids
  soc/tegra: pmc: Use the new reset APIs to manage reset controllers
  soc: mediatek: update power domain data of MT2712
  dt-bindings: soc: update MT2712 power dt-bindings
  cpufreq: scmi: add thermal dependency
  soc: mediatek: fix the mistaken pointer accessed when subdomains are added
  soc: mediatek: add SCPSYS power domain driver for MediaTek MT7623A SoC
  soc: mediatek: avoid hardcoded value with bus_prot_mask
  dt-bindings: soc: add header files required for MT7623A SCPSYS dt-binding
  dt-bindings: soc: add SCPSYS binding for MT7623 and MT7623A SoC
  ...
2018-04-05 21:29:35 -07:00
Arnd Bergmann 9a1651dcc1 cpufreq: remove cris specific drivers
The cris architecture is getting removed, including the artpec3
and etraxfs SoCs, so these cpufreq drivers are now unused.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-03-26 15:56:52 +02:00
Arnd Bergmann 9a3daf58f9 cpufreq: remove blackfin driver
The blackfin architecture is getting removed, so this driver is
now obsolete.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-03-26 15:56:50 +02:00
Sudeep Holla 99d6bdf338 cpufreq: add support for CPU DVFS based on SCMI message protocol
On some ARM based systems, a separate Cortex-M based System Control
Processor(SCP) provides the overall power, clock, reset and system
control including CPU DVFS. SCMI Message Protocol is used to
communicate with the SCP.

This patch adds a cpufreq driver for such systems using SCMI interface
to drive CPU DVFS.

Cc: linux-pm@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
2018-02-28 16:37:57 +00:00
Corentin LABBE 3d70671667 cpufreq: remove at32ap-cpufreq
Since AVR32 arch was removed, at32ap-cpufreq is useless.
Remove this driver.

Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-02-07 11:44:23 +01:00
Gregory CLEMENT 92ce45fb87 cpufreq: Add DVFS support for Armada 37xx
This patch adds DVFS support for the Armada 37xx SoCs

There are up to four CPU frequency loads for Armada 37xx controlled by
the hardware.

This driver associates the CPU load level to a frequency, then the
hardware will switch while selecting a load level.

The hardware also can associate a voltage for each level (AVS support)
but it is not yet supported

Tested-by: Andre Heider <a.heider@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-12-16 17:11:43 +01:00
Gregory CLEMENT 16630642f1 cpufreq: sort the drivers in ARM part
Keep the driver files alphabetically sorted.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-12-16 02:29:42 +01:00
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Linus Walleij 919096f7f3 cpufreq: dbx500: Delete obsolete driver
We have moved the Ux500 over to use the generic DT based
cpufreq driver, so delete the old custom driver.

At the same time select CPUFREQ_DT from the machine's
Kconfig in order to satisfy the "default ARCH_U8500"
selection on the old driver.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-22 15:50:02 +02:00
Marc Gonzalez 9dbd224f9e cpufreq: dt: Don't use generic platdev driver for tango
On tango platforms, firmware configures the CPU clock, and Linux is
then only allowed to use the cpu_clk_divider to change the frequency.
Build the OPP table dynamically at init, in order to support whatever
firmware throws at us.

Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-07-22 02:20:59 +02:00
Sean Wang 501c574f4e cpufreq: mediatek: Add support of cpufreq to MT2701/MT7623 SoC
MT2701/MT7623 is a 32-bit ARMv7 based quad-core (4 * Cortex-A7) with
single cluster and this hardware is also compatible with the existing
driver through enabling CPU frequency feature with operating-points-v2
bindings. Also, this driver actually supports all MediaTek SoCs, the
Kconfig menu entry and file name itself should be updated with more
generic name to drop "MT8173"

Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-07-22 02:19:37 +02:00
Arnd Bergmann be0408d74d cpufreq: dbx500: add a Kconfig symbol
Moving the cooling code into the cpufreq driver caused a possible build failure
when the cpu_thermal helper code is a loadable module or disabled:

drivers/cpufreq/dbx500-cpufreq.o: In function `dbx500_cpufreq_ready':
dbx500-cpufreq.c:(.text.dbx500_cpufreq_ready+0x4): undefined reference to `cpufreq_cooling_register'

This adds the same dependency that we have in other cpufreq drivers,
forcing the driver to be disabled when we can't possibly link it.

Fixes: 19678ffb9f (cpufreq: dbx500: Manage cooling device from cpufreq driver)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-05-14 13:40:16 +02:00
Mikko Perttunen 939dc6f51e cpufreq: Add Tegra186 cpufreq driver
Add a new cpufreq driver for Tegra186 (and likely later).
The CPUs are organized into two clusters, Denver and A57,
with two and four cores respectively. CPU frequency can be
adjusted by writing the desired rate divisor and a voltage
hint to a special per-core register.

The frequency of each core can be set individually; however,
this is just a hint as all CPUs in a cluster will run at
the maximum rate of non-idle CPUs in the cluster.

Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-04-19 23:23:08 +02:00
Dave Gerlach e13cf046cd cpufreq: ti: Add cpufreq driver to determine available OPPs at runtime
Some TI SoCs, like those in the AM335x, AM437x, DRA7x, and AM57x families,
have different OPPs available for the MPU depending on which specific
variant of the SoC is in use. This can be determined through use of the
revision and an eFuse register present in the silicon. Introduce a
ti-cpufreq driver that can read the aformentioned values and provide
them as version matching data to the opp framework. Through this the
opp-supported-hw dt binding that is part of the operating-points-v2
table can be used to indicate availability of OPPs for each device.

This driver also creates the "cpufreq-dt" platform_device after passing
the version matching data to the OPP framework so that the cpufreq-dt
handles the actual cpufreq implementation. Even without the necessary
data to pass the version matching data the driver will still create this
device to maintain backwards compatibility with operating-points v1
tables.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-02-09 22:57:48 +01:00
Markus Mayer cdb56cbfd7 cpufreq: bmips-cpufreq: CPUfreq driver for Broadcom's BMIPS SoCs
Add the MIPS CPUfreq driver. This driver currently supports CPUfreq on
BMIPS5xxx-based SoCs.

Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-02-09 01:22:44 +01:00
Markus Mayer de322e0859 cpufreq: brcmstb-avs-cpufreq: AVS CPUfreq driver for Broadcom STB SoCs
This driver supports voltage and frequency scaling on Broadcom STB SoCs
using AVS firmware with DFS and DVFS support.

Actual frequency or voltage scaling is done exclusively by the AVS
firmware. The driver merely provides a standard CPUfreq interface to
other kernel components and userland, and instructs the AVS firmware to
perform frequency or voltage changes on its behalf.

Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-11-01 06:07:37 +01:00
Linus Walleij ae8b8d8f86 cpufreq: retire the Integrator cpufreq driver
After switching the core module clocks controlling the Integrator
clock frequencies to the common clock framework, defining the
operating points in the device tree, and activating the generic
DT-based CPUfreq driver, we can retire the old Integrator
cpufreq driver.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-11-01 06:01:18 +01:00
Linus Torvalds 07b75260eb Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for MIPS for 4.7.  Here's the summary of
  the changes:

   - ATH79: Support for DTB passuing using the UHI boot protocol
   - ATH79: Remove support for builtin DTB.
   - ATH79: Add zboot debug serial support.
   - ATH79: Add initial support for Dragino MS14 (Dragine 2), Onion Omega
            and DPT-Module.
   - ATH79: Update devicetree clock support for AR9132 and AR9331.
   - ATH79: Cleanup the DT code.
   - ATH79: Support newer SOCs in ath79_ddr_ctrl_init.
   - ATH79: Fix regression in PCI window initialization.
   - BCM47xx: Move SPROM driver to drivers/firmware/
   - BCM63xx: Enable partition parser in defconfig.
   - BMIPS: BMIPS5000 has I cache filing from D cache
   - BMIPS: BMIPS: Add cpu-feature-overrides.h
   - BMIPS: Add Whirlwind support
   - BMIPS: Adjust mips-hpt-frequency for BCM7435
   - BMIPS: Remove maxcpus from BCM97435SVMB DTS
   - BMIPS: Add missing 7038 L1 register cells to BCM7435
   - BMIPS: Various tweaks to initialization code.
   - BMIPS: Enable partition parser in defconfig.
   - BMIPS: Cache tweaks.
   - BMIPS: Add UART, I2C and SATA devices to DT.
   - BMIPS: Add BCM6358 and BCM63268support
   - BMIPS: Add device tree example for BCM6358.
   - BMIPS: Improve Improve BCM6328 and BCM6368 device trees
   - Lantiq: Add support for device tree file from boot loader
   - Lantiq: Allow build with no built-in DT.
   - Loongson 3: Reserve 32MB for RS780E integrated GPU.
   - Loongson 3: Fix build error after ld-version.sh modification
   - Loongson 3: Move chipset ACPI code from drivers to arch.
   - Loongson 3: Speedup irq processing.
   - Loongson 3: Add basic Loongson 3A support.
   - Loongson 3: Set cache flush handlers to nop.
   - Loongson 3: Invalidate special TLBs when needed.
   - Loongson 3: Fast TLB refill handler.
   - MT7620: Fallback strategy for invalid syscfg0.
   - Netlogic: Fix CP0_EBASE redefinition warnings
   - Octeon: Initialization fixes
   - Octeon: Add DTS files for the D-Link DSR-1000N and EdgeRouter Lite
   - Octeon: Enable add Octeon-drivers in cavium_octeon_defconfig
   - Octeon: Correctly handle endian-swapped initramfs images.
   - Octeon: Support CN73xx, CN75xx and CN78xx.
   - Octeon: Remove dead code from cvmx-sysinfo.
   - Octeon: Extend number of supported CPUs past 32.
   - Octeon: Remove some code limiting NR_IRQS to 255.
   - Octeon: Simplify octeon_irq_ciu_gpio_set_type.
   - Octeon: Mark some functions __init in smp.c
   - Octeon: Octeon: Add Octeon III CN7xxx interface detection
   - PIC32: Add serial driver and bindings for it.
   - PIC32: Add PIC32 deadman timer driver and bindings.
   - PIC32: Add PIC32 clock timer driver and bindings.
   - Pistachio: Determine SoC revision during boot
   - Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER.
   - Sibyte: Strip redundant comments from bcm1480_regs.h.
   - Panic immediately if panic_on_oops is set.
   - module: fix incorrect IS_ERR_VALUE macro usage.
   - module: Make consistent use of pr_*
   - Remove no longer needed work_on_cpu() call.
   - Remove CONFIG_IPV6_PRIVACY from defconfigs.
   - Fix registers of non-crashing CPUs in dumps.
   - Handle MIPSisms in new vmcore_elf32_check_arch.
   - Select CONFIG_HANDLE_DOMAIN_IRQ and make it work.
   - Allow RIXI to be used on non-R2 or R6 cores.
   - Reserve nosave data for hibernation
   - Fix siginfo.h to use strict POSIX types.
   - Don't unwind user mode with EVA.
   - Fix watchpoint restoration
   - Ptrace watchpoints for R6.
   - Sync icache when it fills from dcache
   - I6400 I-cache fills from dcache.
   - Various MSA fixes.
   - Cleanup MIPS_CPU_* definitions.
   - Signal: Move generic copy_siginfo to signal.h
   - Signal: Fix uapi include in exported asm/siginfo.h
   - Timer fixes for sake of KVM.
   - XPA TLB refill fixes.
   - Treat perf counter feature
   - Update John Crispin's email address
   - Add PIC32 watchdog and bindings.
   - Handle R10000 LL/SC bug in set_pte()
   - cpufreq: Various fixes for Longson1.
   - R6: Fix R2 emulation.
   - mathemu: Cosmetic fix to ADDIUPC emulation, plenty of other small fixes
   - ELF: ABI and FP fixes.
   - Allow for relocatable kernel and use that to support KASLR.
   - Fix CPC_BASE_ADDR mask
   - Plenty fo smp-cps, CM, R6 and M6250 fixes.
   - Make reset_control_ops const.
   - Fix kernel command line handling of leading whitespace.
   - Cleanups to cache handling.
   - Add brcm, bcm6345-l1-intc device tree bindings.
   - Use generic clkdev.h header
   - Remove CLK_IS_ROOT usage.
   - Misc small cleanups.
   - CM: Fix compilation error when !MIPS_CM
   - oprofile: Fix a preemption issue
   - Detect DSP ASE v3 support:1"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (275 commits)
  MIPS: pic32mzda: fix getting timer clock rate.
  MIPS: ath79: fix regression in PCI window initialization
  MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCs
  MIPS: Fix VZ probe gas errors with binutils <2.24
  MIPS: perf: Fix I6400 event numbers
  MIPS: DEC: Export `ioasic_ssr_lock' to modules
  MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC
  MIPS: CM: Fix compilation error when !MIPS_CM
  MIPS: Fix genvdso error on rebuild
  USB: ohci-jz4740: Remove obsolete driver
  MIPS: JZ4740: Probe OHCI platform device via DT
  MIPS: JZ4740: Qi LB60: Remove support for AVT2 variant
  MIPS: pistachio: Determine SoC revision during boot
  MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435
  mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for the memory type
  MIPS: Prevent "restoration" of MSA context in non-MSA kernels
  MIPS: cevt-r4k: Dynamically calculate min_delta_ns
  MIPS: malta-time: Take seconds into account
  MIPS: malta-time: Start GIC count before syncing to RTC
  MIPS: Force CPUs to lose FP context during mode switches
  ...
2016-05-19 10:02:26 -07:00
Kelvin Cheung 6a1d55ccd8 CPUFREQ: Loongson1: Rename the file to loongson1-cpufreq.c
This patch renames the file to loongson1-cpufreq.c,
and also includes some minor updates.

Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13052/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2016-05-13 14:02:08 +02:00
Viresh Kumar 9f123def55 cpufreq: mvebu: Move cpufreq code into drivers/cpufreq/
Move cpufreq bits for mvebu into drivers/cpufreq/ directory, that's
where they really belong to.

Compiled tested only.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-04-28 15:22:43 +02:00
Viresh Kumar 3920be471c cpufreq: hisilicon: Use generic platdev driver
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-04-25 16:18:24 +02:00
Viresh Kumar f56aad1d98 cpufreq: dt: Add generic platform-device creation support
Multiple platforms are using the generic cpufreq-dt driver now, and all
of them are required to create a platform device with name "cpufreq-dt",
in order to get the cpufreq-dt probed.

Many of them do it from platform code, others have special drivers just
to do that.

It would be more sensible to do this at a generic place, where all such
platform can mark their entries.

This patch adds a separate file to get this device created. Currently
the compat list of platforms that we support is empty, and will be
filled in as and when we move platforms to use it.

It always compiles as part of the kernel and so doesn't need a
module-exit operation.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-04-09 01:18:42 +02:00
Rafael J. Wysocki 2d0c58ad60 cpufreq: governor: Move abstract gov_attr_set code to seperate file
Move abstract code related to struct gov_attr_set to a separate (new)
file so it can be shared with (future) goverernors that won't share
more code with "ondemand" and "conservative".

No intentional functional changes.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
2016-04-02 01:09:01 +02:00
Lee Jones ab0ea257fc cpufreq: st: Provide runtime initialised driver for ST's platforms
The bootloader is charged with the responsibility to provide platform
specific Dynamic Voltage and Frequency Scaling (DVFS) information via
Device Tree.  This driver takes the supplied configuration and
registers it with the new generic OPP framework, to then be used with
CPUFreq.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-12-12 02:55:21 +01:00
Linus Torvalds b44a3d2a85 ARM: SoC driver updates for v4.4
As we've enabled multiplatform kernels on ARM, and greatly done away with
 the contents under arch/arm/mach-*, there's still need for SoC-related
 drivers to go somewhere.
 
 Many of them go in through other driver trees, but we still have
 drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
 that might be shared between ARM and ARM64 (or just in general makes
 sense to not have under the architecture directory).
 
 This branch contains mostly such code:
 
 - Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to communicate
   with power management blocks on these SoCs for use by clock, regulator and
   bus frequency drivers.
 - Allwinner Reduced Serial Bus driver, again used to communicate with PMICs.
 - Drivers for ARM's SCPI (System Control Processor). Not to be confused with
   PSCI (Power State Coordination Interface). SCPI is used to communicate with
   the assistant embedded cores doing power management, and we have yet to see
   how many of them will implement this for their hardware vs abstracting in
   other ways (or not at all like in the past).
 - To make confusion between SCPI and PSCI more likely, this release also
   includes an update of PSCI to interface version 1.0.
 - Rockchip support for power domains.
 - A driver to talk to the firmware on Raspberry Pi.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJWQC+cAAoJEIwa5zzehBx3jEUP/0GpxfDVanEUkudVLLe7J0RH
 CNlRan107Cw6hXRUJo7elEsuCALjccXjc1CAH4+RnNpOAeBKW97n+WU7trTv+wUZ
 sQX4SkBPKFBlgwGF2qhsi5q74gms/BrgtCa4kNb9joOYso039tlfIOPzK80DMkOm
 TkyIJdUCgFJMjCQLhX6kGT0PDcrbIjb6aA2cF3FAVeaJA7uz8lNe/eHJr3oHxIEY
 CvC651yJ2mIHQUU4BJx/AJo+wXg3dRUXNCAtBjwLRPEAzduYZXYm1ZTVIby/1q9r
 dR2KDFEuibODXmXrDBzKNJwCu/TLJEwo/1oPaEIVfY91XLKfiWUhgVqa1o1I+d9U
 XoGPibCW461qFahjQW87MfInALpCOA7/RbTNjFp+MVyipCYvkaYq7KFiYEldgFDx
 z4Qx/J4hYc2TlDWrpNiUCZMfmhwi7y+Ib+tnenYTO1eyMuw0e9mfnVdjk5iU3Pvk
 Ye4qPqpYclJruyHbYi164878+1lLaW2NCUgC3rkBO/GWPAzp7d9iLWoZ3PuyD5i5
 PEjs668UcRdZYbI4rdrhGHL8Eq9Gnuc4Rthu7HxPOK+DG0XgP8r97PhM8aYGYVDO
 +yikBtjWRsA9fPj3rMKA3UsQ61DAeR9LmZ0XPGjWFMCjCG0JlUoIMaA+Uu0i8fr8
 95qxBVxbO7rhL39r1rhV
 =dm+I
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC driver updates from Olof Johansson:
 "As we've enabled multiplatform kernels on ARM, and greatly done away
  with the contents under arch/arm/mach-*, there's still need for
  SoC-related drivers to go somewhere.

  Many of them go in through other driver trees, but we still have
  drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
  that might be shared between ARM and ARM64 (or just in general makes
  sense to not have under the architecture directory).

  This branch contains mostly such code:

   - Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
     communicate with power management blocks on these SoCs for use by
     clock, regulator and bus frequency drivers.

   - Allwinner Reduced Serial Bus driver, again used to communicate with
     PMICs.

   - Drivers for ARM's SCPI (System Control Processor).  Not to be
     confused with PSCI (Power State Coordination Interface).  SCPI is
     used to communicate with the assistant embedded cores doing power
     management, and we have yet to see how many of them will implement
     this for their hardware vs abstracting in other ways (or not at all
     like in the past).

   - To make confusion between SCPI and PSCI more likely, this release
     also includes an update of PSCI to interface version 1.0.

   - Rockchip support for power domains.

   - A driver to talk to the firmware on Raspberry Pi"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
  soc: qcom: smd-rpm: Correct size of outgoing message
  bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
  bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
  ARM: bcm2835: add mutual inclusion protection
  drivers: psci: make PSCI 1.0 functions initialization version dependent
  dt-bindings: Correct paths in Rockchip power domains binding document
  soc: rockchip: power-domain: don't try to print the clock name in error case
  soc: qcom/smem: add HWSPINLOCK dependency
  clk: berlin: add cpuclk
  ARM: berlin: dts: add CLKID_CPU for BG2Q
  ARM: bcm2835: Add the Raspberry Pi firmware driver
  soc: qcom: smem: Move RPM message ram out of smem DT node
  soc: qcom: smd-rpm: Correct the active vs sleep state flagging
  soc: qcom: smd: delete unneeded of_node_put
  firmware: qcom-scm: build for correct architecture level
  soc: qcom: smd: Correct SMEM items for upper channels
  qcom-scm: add missing prototype for qcom_scm_is_available()
  qcom-scm: fix endianess issue in __qcom_scm_is_call_available
  soc: qcom: smd: Reject send of too big packets
  soc: qcom: smd: Handle big endian CPUs
  ...
2015-11-10 15:00:03 -08:00
Rafael J. Wysocki 394f7164e6 Merge branch 'pm-opp'
* pm-opp:
  PM / OPP: passing NULL to PTR_ERR()
  PM / OPP: Move cpu specific code to opp/cpu.c
  PM / OPP: Move opp core to its own directory
  PM / OPP: Prefix exported opp routines with dev_pm_opp_
  PM / OPP: Rename opp init/free table routines
  PM / OPP: reuse of_parse_phandle()
2015-11-02 00:54:37 +01:00
Ashwin Chaugule 5477fb3bd1 ACPI / CPPC: Add a CPUFreq driver for use with CPPC
This driver utilizes the methods introduced in a previous
patch titled - "ACPI: Introduce CPU performance controls using CPPC"
and enables usage with existing CPUFreq governors.

Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Reviewed-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-12 23:04:31 +02:00
Sudeep Holla 8def31034d cpufreq: arm_big_little: add SCPI interface driver
On some ARM based systems, a separate Cortex-M based System Control
Processor(SCP) provides the overall power, clock, reset and system
control including CPU DVFS. SCPI Message Protocol is used to
communicate with the SCPI.

This patch adds a interface driver for adding OPPs and registering
the arm_big_little cpufreq driver for such systems.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
2015-09-28 11:53:38 +01:00
Viresh Kumar 33692dc381 PM / OPP: Move opp core to its own directory
OPP code is expanding and is already present in multiple directories
(cpufreq and power). Lets move it to its own directory, to manage it
better.

This also moves/renames the cpufreq_opp file to cpu.c, as it will
contain helpers for cpu device. Its not just about cpufreq, other
frameworks can use OPPs as well.

Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-09-15 02:03:16 +02:00
Linus Torvalds d71fc239b6 ARM: SoC: late fixes and dependencies
This is a collection of a few late fixes and other misc. stuff that
 had dependencies on things being merged from other trees.
 
 The bulk of the changes are for samsung/exynos SoCs for some changes
 that needed a few minor reworks so ended up a bit late.  The others
 are mainly for qcom SoCs: a couple fixes and some DTS updates.
 
 There's one conflict with drivers/cpufreq/exynos-cpufreq.c because
 it's now been completely removed, but there were some fixes that hit
 mainline in the meantime.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIbBAABAgAGBQJV8fkAAAoJEFk3GJrT+8Zllf8P9jj3+TnvbJS/8bWoQoB7BRUZ
 LZPgi2+sBXylrBV60uQdyodiTHQUMZhbL7GvgEVG0z6yyin7nyijqNkulTbQbWmg
 WhumLNCNcs8vlZegA/corbwgcVC7FkjOP97HveTe2mgwZ+GaXj9qMRQzBsMqSXEo
 4890ZeP1nWBTP42oXOQHkNyKWFBjuERK0dTw2MXj7WE0/Ag8i7ERp76uJQdQ7V5O
 BpNRwxp3vSCky8rxbpD/avWdlspv1yZGBQyLeIreVq2YQFojvT36K8wHcf6iWBT/
 pzGGV/uZM7MnrGZdqSfVEMDHl7Z2s7Ls+sv5F6Md7ErnVDerHGRjw/6lJDjbeH7u
 trucpsuhz5yhTjpZssGHH2NT8pWxxh8M+AaNOiiH8PuYESAbPAmWLpWkn+648bIn
 P++Z90DIyfNEqnNSMHkcQYpVt8zc4g75gZfTIIsXLB+DLgzgSK8ergrfyRN/O0zj
 oFY35g3wHdgisnGve+BAW30zTZtP19TMT36OltWjIkjuRZC29PS2vkH8eTETdVXx
 01f/qcpbB1L1rXfIBjNkjx81j89XPd68JIBfctTF5QBOAGm/Dix6tj2mU/N7TNu5
 TrBmD3CXdOQbCPaoK/qWX7/b11IN/XOlGL06hhYwbSdvCVy7rNccApXvfnrDWziK
 Ly923FP1OB7h0Kk1cmo=
 =85Ck
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull late ARM SoC updates from Kevin Hilman:
 "This is a collection of a few late fixes and other misc stuff that had
  dependencies on things being merged from other trees.

  The bulk of the changes are for samsung/exynos SoCs for some changes
  that needed a few minor reworks so ended up a bit late.  The others
  are mainly for qcom SoCs: a couple fixes and some DTS updates"

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
  ARM: multi_v7_defconfig: Enable PBIAS regulator
  soc: qcom: smd: Correct fBLOCKREADINTR handling
  soc: qcom: smd: Use correct remote processor ID
  soc: qcom: smem: Fix errant private access
  ARM: dts: qcom: msm8974-sony-xperia-honami: Use stdout-path
  ARM: dts: qcom: msm8960-cdp: Use stdout-path
  ARM: dts: qcom: msm8660-surf: Use stdout-path
  ARM: dts: qcom: ipq8064-ap148: Use stdout-path
  ARM: dts: qcom: apq8084-mtp: Use stdout-path
  ARM: dts: qcom: apq8084-ifc6540: Use stdout-path
  ARM: dts: qcom: apq8074-dragonboard: Use stdout-path
  ARM: dts: qcom: apq8064-ifc6410: Use stdout-path
  ARM: dts: qcom: apq8064-cm-qs600: Use stdout-path
  ARM: dts: qcom: Label serial nodes for aliasing and stdout-path
  reset: ath79: Fix missing spin_lock_init
  reset: Add (devm_)reset_control_get stub functions
  ARM: EXYNOS: switch to using generic cpufreq driver for exynos4x12
  cpufreq: exynos: Remove unselectable rule for arm-exynos-cpufreq.o
  ARM: dts: add iommu property to JPEG device for exynos4
  ARM: dts: enable SPI1 for exynos4412-odroidu3
  ...
2015-09-10 17:59:04 -07:00
Linus Torvalds ae98207309 Power management and ACPI material for v4.3-rc1
- ACPICA update to upstream revision 20150818 including method
    tracing extensions to allow more in-depth AML debugging in the
    kernel and a number of assorted fixes and cleanups (Bob Moore,
    Lv Zheng, Markus Elfring).
 
  - ACPI sysfs code updates and a documentation update related to
    AML method tracing (Lv Zheng).
 
  - ACPI EC driver fix related to serialized evaluations of _Qxx
    methods and ACPI tools updates allowing the EC userspace tool
    to be built from the kernel source (Lv Zheng).
 
  - ACPI processor driver updates preparing it for future
    introduction of CPPC support and ACPI PCC mailbox driver
    updates (Ashwin Chaugule).
 
  - ACPI interrupts enumeration fix for a regression related
    to the handling of IRQ attribute conflicts between MADT
    and the ACPI namespace (Jiang Liu).
 
  - Fixes related to ACPI device PM (Mika Westerberg, Srinidhi Kasagar).
 
  - ACPI device registration code reorganization to separate the
    sysfs-related code and bus type operations from the rest (Rafael
    J Wysocki).
 
  - Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
    Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).
 
  - ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups
    (Pan Xinhui, Rafael J Wysocki).
 
  - cpufreq core cleanups on top of the previous changes allowing it
    to preseve its sysfs directories over system suspend/resume (Viresh
    Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).
 
  - cpufreq fixes and cleanups related to governors (Viresh Kumar).
 
  - cpufreq updates (core and the cpufreq-dt driver) related to the
    turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).
 
  - New DT bindings for Operating Performance Points (OPP), support
    for them in the OPP framework and in the cpufreq-dt driver plus
    related OPP framework fixes and cleanups (Viresh Kumar).
 
  - cpufreq powernv driver updates (Shilpasri G Bhat).
 
  - New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).
 
  - Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
    and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).
 
  - intel_pstate driver updates including Skylake-S support, support
    for enabling HW P-states per CPU and an additional vendor bypass
    list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).
 
  - cpuidle core fixes related to the handling of coupled idle states
    (Xunlei Pang).
 
  - intel_idle driver updates including Skylake Client support and
    support for freeze-mode-specific idle states (Len Brown).
 
  - Driver core updates related to power management (Andy Shevchenko,
    Rafael J Wysocki).
 
  - Generic power domains framework fixes and cleanups (Jon Hunter,
    Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).
 
  - Device PM QoS framework update to allow the latency tolerance
    setting to be exposed to user space via sysfs (Mika Westerberg).
 
  - devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
    exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).
 
  - System sleep support updates (Alan Stern, Len Brown, SungEun Kim).
 
  - rockchip-io AVS support updates (Heiko Stuebner).
 
  - PM core clocks support fixup (Colin Ian King).
 
  - Power capping RAPL driver update including support for Skylake H/S
    and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).
 
  - Generic device properties framework fixes related to the handling
    of static (driver-provided) property sets (Andy Shevchenko).
 
  - turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
    Shreyas B Prabhu).
 
 /
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iQIcBAABCAAGBQJV5hhGAAoJEILEb/54YlRxs+EQAK51iFk48+IbpHYaZZ50Yo4m
 ZZc2zBcbwRcBlU9vKERrhG+jieSl8J/JJNxT8vBjKqyvNw038mCjewQh02ol0HuC
 R7nlDiVJkmZ50sLO4xwE/1UBZr/XqbddwCUnYzvFMkMTA0ePzFtf8BrJ1FXpT8S/
 fkwSXQty6hvJDwxkfrbMSaA730wMju9lahx8D6MlmUAedWYZOJDMQKB4WKa/St5X
 9uckBPHUBB2KiKlXxdbFPwKLNxHvLROq5SpDLc6cM/7XZB+QfNFy85CUjCUtYo1O
 1W8k0qnztvZ6UEv27qz5dejGyAGOarMWGGNsmL9evoeGeHRpQL+dom7HcTnbAfUZ
 walyhYSm/zKkdy7Vl3xWUUQkMG48+PviMI6K0YhHXb3Rm5wlR/yBNZTwNIty9SX/
 fKCHEa8QynWwLxgm53c3xRkiitJxMsHNK03moLD9zQMjshTyTNvpNbZoahyKQzk6
 H+9M1DBRHhkkREDWSwGutukxfEMtWe2vcZcyERrFiY7l5k1j58DwDBMPqjPhRv6q
 P/1NlCzr0XYf83Y86J18LbDuPGDhTjjIEn6CqbtI2mmWqTg3+rF7zvS2ux+FzMnA
 gisv8l6GT9JiWhxKFqqL/rrVpwtyHebWLYE/RpNUW6fEzLziRNj1qyYO9dqI/GGi
 I3rfxlXoc/5xJWCgNB8f
 =fTgI
 -----END PGP SIGNATURE-----

Merge tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull power management and ACPI updates from Rafael Wysocki:
 "From the number of commits perspective, the biggest items are ACPICA
  and cpufreq changes with the latter taking the lead (over 50 commits).

  On the cpufreq front, there are many cleanups and minor fixes in the
  core and governors, driver updates etc.  We also have a new cpufreq
  driver for Mediatek MT8173 chips.

  ACPICA mostly updates its debug infrastructure and adds a number of
  fixes and cleanups for a good measure.

  The Operating Performance Points (OPP) framework is updated with new
  DT bindings and support for them among other things.

  We have a few updates of the generic power domains framework and a
  reorganization of the ACPI device enumeration code and bus type
  operations.

  And a lot of fixes and cleanups all over.

  Included is one branch from the MFD tree as it contains some
  PM-related driver core and ACPI PM changes a few other commits are
  based on.

  Specifics:

   - ACPICA update to upstream revision 20150818 including method
     tracing extensions to allow more in-depth AML debugging in the
     kernel and a number of assorted fixes and cleanups (Bob Moore, Lv
     Zheng, Markus Elfring).

   - ACPI sysfs code updates and a documentation update related to AML
     method tracing (Lv Zheng).

   - ACPI EC driver fix related to serialized evaluations of _Qxx
     methods and ACPI tools updates allowing the EC userspace tool to be
     built from the kernel source (Lv Zheng).

   - ACPI processor driver updates preparing it for future introduction
     of CPPC support and ACPI PCC mailbox driver updates (Ashwin
     Chaugule).

   - ACPI interrupts enumeration fix for a regression related to the
     handling of IRQ attribute conflicts between MADT and the ACPI
     namespace (Jiang Liu).

   - Fixes related to ACPI device PM (Mika Westerberg, Srinidhi
     Kasagar).

   - ACPI device registration code reorganization to separate the
     sysfs-related code and bus type operations from the rest (Rafael J
     Wysocki).

   - Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
     Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).

   - ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups (Pan
     Xinhui, Rafael J Wysocki).

   - cpufreq core cleanups on top of the previous changes allowing it to
     preseve its sysfs directories over system suspend/resume (Viresh
     Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).

   - cpufreq fixes and cleanups related to governors (Viresh Kumar).

   - cpufreq updates (core and the cpufreq-dt driver) related to the
     turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).

   - New DT bindings for Operating Performance Points (OPP), support for
     them in the OPP framework and in the cpufreq-dt driver plus related
     OPP framework fixes and cleanups (Viresh Kumar).

   - cpufreq powernv driver updates (Shilpasri G Bhat).

   - New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).

   - Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
     and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).

   - intel_pstate driver updates including Skylake-S support, support
     for enabling HW P-states per CPU and an additional vendor bypass
     list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).

   - cpuidle core fixes related to the handling of coupled idle states
     (Xunlei Pang).

   - intel_idle driver updates including Skylake Client support and
     support for freeze-mode-specific idle states (Len Brown).

   - Driver core updates related to power management (Andy Shevchenko,
     Rafael J Wysocki).

   - Generic power domains framework fixes and cleanups (Jon Hunter,
     Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).

   - Device PM QoS framework update to allow the latency tolerance
     setting to be exposed to user space via sysfs (Mika Westerberg).

   - devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
     exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).

   - System sleep support updates (Alan Stern, Len Brown, SungEun Kim).

   - rockchip-io AVS support updates (Heiko Stuebner).

   - PM core clocks support fixup (Colin Ian King).

   - Power capping RAPL driver update including support for Skylake H/S
     and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).

   - Generic device properties framework fixes related to the handling
     of static (driver-provided) property sets (Andy Shevchenko).

   - turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
     Shreyas B Prabhu)"

* tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (180 commits)
  cpufreq: speedstep-lib: Use monotonic clock
  cpufreq: powernv: Increase the verbosity of OCC console messages
  cpufreq: sfi: use kmemdup rather than duplicating its implementation
  cpufreq: drop !cpufreq_driver check from cpufreq_parse_governor()
  cpufreq: rename cpufreq_real_policy as cpufreq_user_policy
  cpufreq: remove redundant 'policy' field from user_policy
  cpufreq: remove redundant 'governor' field from user_policy
  cpufreq: update user_policy.* on success
  cpufreq: use memcpy() to copy policy
  cpufreq: remove redundant CPUFREQ_INCOMPATIBLE notifier event
  cpufreq: mediatek: Add MT8173 cpufreq driver
  dt-bindings: mediatek: Add MT8173 CPU DVFS clock bindings
  PM / Domains: Fix typo in description of genpd_dev_pm_detach()
  PM / Domains: Remove unusable governor dummies
  PM / Domains: Make pm_genpd_init() available to modules
  PM / domains: Align column headers and data in pm_genpd_summary output
  powercap / RAPL: disable the 2nd power limit properly
  tools: cpupower: Fix error when running cpupower monitor
  PM / OPP: Drop unlikely before IS_ERR(_OR_NULL)
  PM / OPP: Fix static checker warning (broken 64bit big endian systems)
  ...
2015-09-01 19:45:46 -07:00
Pi-Cheng Chen 1453863fb0 cpufreq: mediatek: Add MT8173 cpufreq driver
Mediatek MT8173 is an ARMv8 based quad-core (2*Cortex-A53 and
2*Cortex-A72) SoC with duall clusters. For each cluster, two voltage
inputs, Vproc and Vsram are supplied by two regulators. For the big
cluster, two regulators come from different PMICs. In this case, when
scaling voltage inputs of the cluster, the voltages of two regulator
inputs need to be controlled by software explicitly under the SoC
specific limitation:

	100mV < Vsram - Vproc < 200mV

which is called 'voltage tracking' mechanism. And when scaling the
frequency of cluster clock input, the input MUX need to be parented to
another "intermediate" stable PLL first and reparented to the original
PLL once the original PLL is stable at the target frequency. This patch
implements those mechanisms to enable CPU DVFS support for Mediatek
MT8173 SoC.

Signed-off-by: Pi-Cheng Chen <pi-cheng.chen@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-09-01 15:50:20 +02:00
Jonas Rabenstein 5e3863a74f cpufreq: exynos: Remove unselectable rule for arm-exynos-cpufreq.o
Commit 966f2a71a9 ("cpufreq: exynos: remove Exynos4x12 specific
cpufreq driver support") deleted option ARM_EXYNOS_CPUFREQ but missed
to delete a rule in drivers/cpufreq/Makefile which depends on that
option.

Remove unselectable rule for arm-exynos-cpufreq.o
from drivers/cpufreq/Makefile.

Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
2015-08-14 02:36:33 +09:00
Bartlomiej Zolnierkiewicz 966f2a71a9 cpufreq: exynos: remove Exynos4x12 specific cpufreq driver support
Exynos4x12 based platforms have switched over to use generic
cpufreq driver for cpufreq functionality.  So the Exynos
specific cpufreq support for these platforms can be removed.

Also once Exynos4x12 based platforms support have been removed
the shared exynos-cpufreq driver is no longer needed and can
be deleted.

Based on the earlier work by Thomas Abraham.

Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
2015-08-14 02:01:42 +09:00
Bartlomiej Zolnierkiewicz ac4c90c82e cpufreq: exynos: remove exynos5250 specific cpufreq driver support
Exynos5250 based platforms have switched over to use generic
cpufreq driver for cpufreq functionality. So the Exynos
specific cpufreq support for these platforms can be removed.

Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[k.kozlowski: Rebased the patch around exynos-cpufreq.c]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
2015-07-24 12:16:12 +09:00
Tuomas Tynkkynen 9eb15dbbfa cpufreq: Add cpufreq driver for Tegra124
Add a new cpufreq driver for Tegra124. Instead of using the PLLX as
the CPU clocksource, switch immediately to the DFLL. It allows the use
of higher clock rates, and will automatically scale the CPU voltage as
well. Besides the CPU clocksource switch, we let the cpufreq-dt driver
for all the cpufreq operations.

This driver also relies on the DFLL driver to fill the OPP table for the
CPU0 device, so that the cpufreq-dt driver knows what frequencies to
use.

Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-07-16 09:34:09 +02:00
Tuomas Tynkkynen 109e13eaa4 cpufreq: tegra: Rename tegra-cpufreq to tegra20-cpufreq
The Tegra124 will use a different driver for frequency scaling, so
rename the old driver (which handles only Tegra20) appropriately.

Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-07-16 09:34:08 +02:00
Thomas Abraham 8eb92ab68f cpufreq: exynos: remove Exynos4210 specific cpufreq driver support
Exynos4210 based platforms have switched over to use generic
cpufreq driver for cpufreq functionality. So the Exynos
specific cpufreq support for these platforms can be removed.

Changes by Bartlomiej:
- dropped Exynos5250 support removal for now
- updated exynos-cpufreq.[c,h]

Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
2015-06-20 12:17:44 -07:00
Leo Yan 5acb972fed cpufreq: hisilicon: add acpu driver
Add acpu driver for hisilicon SoC, acpu is application processor
subsystem. Currently the acpu has the coupled clock domain for two
clusters, so this driver will directly use cpufreq-dt driver as
backend.

Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-04-02 02:24:54 +02:00
Tang Yuantian 2f249358ee cpufreq: qoriq: rename the driver
This driver works on all QorIQ platforms which include
ARM-based cores and PPC-based cores.
Rename it in order to represent better.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-03-18 22:35:16 +01:00
Linus Torvalds 3d883483dc Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull more thermal managament updates from Zhang Rui:
 "Specifics:

   - Exynos thermal driver refactoring.  Several cleanups, code
     optimization, unused symbols removal, and unused feature removal in
     Exynos thermal driver.  Thanks Lukasz for this effort.

   - Exynos thermal driver support to OF thermal.  After the code
     refactoring, the driver earned the support to OF thermal.  Chip
     thermal data were moved from driver code to DTS, reducing the code
     footprint.  Thanks Lukasz for this.

   - After receiving the OF thermal support, the exynos thermal driver
     now must allow modular build.  Thanks Arnd for detecting, reporting
     and fixing this.

   - Exynos thermal driver support to Exynos 7 SoC.  Thanks Abhilash for
     this.

   - Accurate temperature reporting on Rockchip thermal driver, thanks
     to Caesar.

   - Fix on how OF thermal enables its zones, thanks Lukasz for fixing.

   - Fixes in OF thermal examples under Documentation/.  Thanks Srinivas
     for fixing"

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
  thermal: exynos: Add TMU support for Exynos7 SoC
  dts: Documentation: Add documentation for Exynos7 SoC thermal bindings
  cpufreq: exynos: allow modular build
  thermal: Fix examples in DT documentation
  thermal: exynos: Correct sanity check at exynos_report_trigger() function
  thermal: Kconfig: Remove config for not used EXYNOS_THERMAL_CORE
  thermal: exynos: Remove exynos_tmu_data.c file
  thermal: rockchip: make temperature reporting much more accurate
  thermal: exynos: Remove exynos_thermal_common.[c|h] files
  thermal: samsung: core: Exynos TMU rework to use device tree for configuration
  dts: Documentation: Update exynos-thermal.txt example for Exynos5440
  dts: Documentation: Extending documentation entry for exynos-thermal
  cpufreq: exynos: Use device tree to determine if cpufreq cooling should be registered
  thermal: exynos: Modify exynos thermal code to use device tree for cpu cooling configuration
  thermal: exynos: Provide thermal_exynos.h file to be included in device tree files
  thermal: exynos: cosmetic: Correct comment format
  thermal: of: Enable thermal_zoneX when sensor is correctly added
2015-02-19 17:51:22 -08:00
Rafael J. Wysocki c488ea4613 Merge branch 'sfi' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux into pm-cpufreq
Pull SFI-based cpufreq driver for v3.20 from Len Brown.

* 'sfi' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  cpufreq: Add SFI based cpufreq driver support
  SFI: fix compiler warnings
2015-02-09 23:43:53 +01:00
Arnd Bergmann 8b2b4a4e53 cpufreq: exynos: allow modular build
The exynos cpufreq driver code recently gained a dependency on the
cooling code, which may be a loadable module. This breaks an ARM
allmodconfig build:

drivers/built-in.o: In function `exynos_cpufreq_probe':
:(.text+0x1748e8): undefined reference to `of_cpufreq_cooling_register'

To avoid this problem, change cpufreq Kconfig to allow the drivers
to be loadable modules as well and enforce a dependency on the
thermal module.

This change, in order to allow module builds on this cpufreq
driver, properly constructs the driver into a single module,
instead of several modules. The change also keeps the proper
platform dependency, and therefore, it wont load in platforms
that are not supposed to be loaded. The user will be able to
build the support for all platforms, or select which platforms
(s)he wants (as originally), except that now it can be a module,
instead.

Besides, it will still keep the driver only on those configs
that expect it to be on. And it won't compile/load on platforms
that it is not supposed to. It brings the config ARM_EXYNOS_CPU_FREQ_BOOST_SW
closer to this driver, so it looks better in the menuconfig.

We intentionally change ARM_EXYNOS5440_CPUFREQ to be tristate too, to
avoid future troubles.

Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-pm@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Fixes: e725d26c48 ("cpufreq: exynos: Use device tree to determine if cpufreq cooling should be registered")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
2015-01-31 14:56:27 -04:00
Srinidhi Kasagar e7ddf4b7b3 cpufreq: Add SFI based cpufreq driver support
This adds the SFI based cpu freq driver for some of the Intel's
Silvermont based Atom architectures like Z34xx and Z35xx.

Signed-off-by: Rudramuni, Vishwesh M <vishwesh.m.rudramuni@intel.com>
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Len Brown <len.brown@intel.com>
2014-12-20 13:37:37 -05:00
Petr Cvek 608eab2282 cpufreq: pxa2xx: Add Kconfig entry
Add ability for PXA2xx CPUFreq to be compiled as a module or not at all.

Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2014-11-27 01:53:12 +01:00
Kelvin Cheung a0a22cf144 cpufreq: Loongson1: Add cpufreq driver for Loongson1B
This patch adds cpufreq driver for Loongson1B which
is capable of changing the CPU frequency dynamically.

Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2014-11-06 01:23:44 +01:00