Add acpiphp to the MAINTAINERS file.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If pcie_portdrv_probe() fails but it had already called
pci_enable_device(), then call pci_disable_device() when
returning error.
Is there some reason that this isn't being done?
or was it just missed?
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Wait until all users have closed their device context before allowing
device unregistration to complete. This prevents a crash caused by
referring to stale data structures.
A better solution would be to have a way to revoke contexts rather
than waiting for userspace to close the context, but that's a much
bigger change that will have to wait. For now let's at least avoid
the crash.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove references to the IPoIB IETF working group as it has been closed.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Data corruption has been seen with Mellanox SRP targets when FMRs
create a memory region with I/O virtual address != 0. Add a
workaround that disables FMR merging for Mellanox targets (OUI 0002c9).
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Protect against srp_reset_device() clearing the req_queue while
srp_reconnect_target() is in progress (note that state change at
the top of srp_reconnect_target() is not sufficient for this since
srp_reset_device() ignores the state).
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Report error code rather than success (0) on failure allocating
timewait_info in ib_send_cm_req().
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Define a constant MTHCA_ARRAY_MASK to replace repeated uses of
(PAGE_SIZE / sizeof (void *) - 1) in mthca array code.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_array_clear() does not clear the slot if the used count is
positive. This leads to crashes in mthca_qp_event() since that uses
mthca_array_get() to check that the qp is valid.
Discovered by Ali Ayoub.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Michael C Thompson wrote: [Tue Aug 01 2006, 02:36:36PM EDT]
> The trigger for this oops is:
> # auditctl -a exit,always -S pread64 -F 'inode<1'
Setting the err value will fix it.
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Always initialize the audit_inode_hash[] so we don't oops on list rules.
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When an object is created via a symlink into an audited directory, audit misses
the event due to not having collected the inode data for the directory. Modify
__audit_inode_child() to copy the parent inode data if a parent wasn't found in
audit_names[].
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When the specified path is an existing file or when it is a symlink, audit
collects the wrong inode number, which causes it to miss the open() event.
Adding a second hook to the open() path fixes this.
Also add audit_copy_inode() to consolidate some code.
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (24 commits)
Revert "[PATCH] USB: move usb_device_class class devices to be real devices"
Revert "[PATCH] USB: convert usb class devices to real devices"
USB: UHCI: Don't test the Short Packet Detect bit
USB: unusual_devs entry for Nokia 3250
USB: dummy-hcd: disable interrupts during req->complete
USB: fix the USB_GADGET_DUMMY_HCD dependencies
USB: ati_remote.c: autorepeat fix
USB: doc: fixes devio.c location in proc_usb_info.txt.
USB: doc: usb-help.txt update.
USB: Patch for rtl8150 to fix unplug problems
USB: cypress driver comment updates
USB: unusual_devs device removal
usb-storage: Add US_FL_IGNORE_DEVICE flag; ignore ZyXEL G220F
USB: New USB ID for Belkin Serial Adapter
USB: Additional PID for the ftdi_sio driver
USB: adding support for SHARP WS003SH to ipaq.c
USB: Fix Freescale high-speed USB host dependency
USB: Removed 3-port device handler from Option driver
USB: Drop Sierra Wireless MC8755 from the Option driver
USB: Let option driver handle Anydata CDMA modems. Remove anydata driver.
...
If CONFIG_IOMMU_DEBUG is set force_iommu defaults to 1. In the case
where no HW IOMMU is present in the machine and we end up using nommu,
leaving force_iommu set to 1 causes dma_alloc_coherent to do the wrong
thing. Therefore, if we end up using nommu, make sure force_iommu is
0.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Re-add backlink for old style unwinder to stack switching. Add proper
stack frame and CFI annotations to call_softirq
This prevents a oops when backtracing with fallback through the
interrupt stack top.
Suggested by Jan Beulich and Herbert Xu wanted it in 2.6.18.
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Suresh points out that commit b0423a0d9c
broke the semantics of a synchronous signal like SIGSEGV occurring
recursively inside its own handler handler (or, indeed, any other
context when the signal was blocked).
That was unintentional, and this fixes things up by reinstating the old
semantics, but without reverting the cleanups.
Cc: Paul E. McKenney <paulmck@us.ibm.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-2.6.18:
gitignore: gitignore quilt's files
kbuild: always use $(CC) for $(call cc-version)
kconfig: correct oldconfig for unset choice options
kbuild: -fno-stack-protector is not good
kbuild: fix typo in modpost
kbuild: improve error from file2alias
kbuild: .gitignore utsrelease.h
kbuild: version.h and new headers_* targets does not require a kernel config
kbuild: hardcode value of YACC&LEX for aic7-triple-x
This reverts c182274ffe commit because it
required a newer version of udev to work properly than what is currently
documented in Documentation/Changes.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts bd00949647 commit because it
required a newer version of udev to work properly than what is currently
documented in Documentation/Changes.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Apparently some UHCI controllers change the value of the Short Packet
Detect (SPD) bit in the TD status word -- presumably when they receive a
short packet. This patch (as759) changes uhci-hcd to avoid assuming
that the bit is unchanged; in fact, the driver no longer looks at SPD at
all.
This fixes the second problem reported in Bugzilla #6752.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is another unusual_devs entry (as760) for another Nokia device,
this time the 3250.
From: Mario Rettig <mariorettig@web.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as756) fixes a bug in dummy-hcd found by the lockdep
checker. In one of the code paths, the driver did not disable
interrupts before calling a request completion routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If USB=m, USB_GADGET=y, the option USB_GADGET_DUMMY_HCD mustn't be
offered since selecting it results in a compile error.
This patch fixes kernel Bugzilla #6534 reported by Toralf Frster.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When HZ is set to 250 (new default) or 100, the time span during which
repeated events from the device are ignored could be too small due to
ms->jiffies rounding. This causes the auto repeat to kick in early making
it impossible for the user to generate individual press/release events.
Increate the timeout to compensate.
Signed-off-by: Marko Macek <Marko.Macek@gmx.net>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The RTL8150 driver currently crashes the kernel if the USB lead is unplugged
while the device is active. The attached patch adds error handling to
tell the network layer that the device has gone away when the device is
unplugged. With this patch, the device can be plugged and unplugged
to one's hearts' content, without crashing anything.
Oh, I've also added rudimentary suspend and resume methods.
Signed-off-by: Peter Chubb <peter@gelato.unsw.edu.au>
Acked-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This entry has been a mystery for some time. I had sent this patch as an
RFC a while ago, and now we've had two reports of this not being needed,
so I'm removing it.
In the event there are reports of breakage, we should revert this patch,
but add a US_FL_NEED_OVERRIDE flag.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new unusual_devs flag for when usb-storage needs to ignore
a device that it would otherwise claim.
We need to ignore the ZyXEL G220F as it is a virtual CDROM drive which
includes the windows driver for this USB-WLAN adapter. After the windows
driver is installed on a windows system, it converts it into a WLAN adapter
(by ejecting the virtual disc).
The virtual CDROM is of no interest to Linux users. The zd1211rw driver will
automatically perform the eject operation, we just need to ensure that
usb-storage does not claim the device.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Can you add the USB IDs for the Belkin USB Serial adapter (P/N F5U257)
to the pl2303 driver in the Linux Kernel? Are you the appropriate person
to approach for this?
I recently purchased a Belkin USB Serial adapter (P/N F5U257) and found
that it didn't work. After a bit of experimentation I found that it
works with the pl2303 driver once the ID has been added. See attached
patch to fix this. Also attached is the output from lsusb -v just in
case you require any information from there.
From: Kim Oldfield <luv@oldfield.wattle.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a short patch which adds one PID to the set of devices
supported by the ftdi_sio driver. The device in question is a
DLP module used as part of a ham radio USB-to-packet adapter.
From: Dave Platt <dplatt@radagast.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This small patch enables a support of "SHARP WS003SH".
"SHARP WS003SH" (usullary called "W-ZERO3") is most polular All-in-one handheld
CellPhone-plus-WindowsMobile5.0 in Japan.
"SHARP WS003SH" has two modes, "Modem" and "ActiveSync".
But, "ActiveSync" mode uses NDIS connection.
Therefore, ipaq.c can only support "Modem" mode.
http://www.sharp.co.jp/ws/ (Japanese Site)
http://greggman.com/edit/editheadlines/2005-12-24.htm
From: Norihiko Tomiyama <norihiko.tomiyama@ctc-g.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The high-speed USB SOC only exists on MPC834x family not MPC83xx family.
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The short driver names were not unique,
which prevented the driver from actually loading.
Also, one of the ioctl pointers was missing.
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OHCI updates for AT91 series processors:
- Get ready for at91sam926x processors (ARMv5tej not ARMv4t)
- Suspend/resume support now behaves properly
- In "standby" mode, OHCI can be a source of system wakeup events
(remote wakeup, device connect/disconnect, etc)
And minor cleanups.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
UDC updates for AT91 series processors:
- Get ready for at91sam926x processors (ARMv5tej not ARMv4t)
- Suspend/resume support now behaves properly
- In "standby" mode, UDC can be a source of system wakeup events
(host resume, device connect/disconnect, etc)
- Fix IRQ storming issues, seemingly related to clock disabling
changes that went in a while back
And minor cleanups, especially whitespace.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kristen Carlson Accardi
Randy Dunlap
Henrik Kretzschmar
Jack Morgenstein
Or Gerlitz
Ishai Rabinovitz
Sean Hefty
Roland Dreier
Michael S. Tsirkin
Al Viro
Amy Griffis
Linus Torvalds
Muli Ben-Yehuda
Andi Kleen
Greg Kroah-Hartman
Alan Stern
Adrian Bunk
Marko Macek
Luiz Fernando N. Capitulino
Peter Chubb
Oliver Bock
Phil Dibowitz
Daniel Drake
Kim Oldfield
Dave Platt
Norihiko Tomiyama
Li Yang
Matthias Urlichs
David Brownell