To support PCIe hot plug in IOMMU, we register a notifier to respond to device
change action.
When the notifier gets BUS_NOTIFY_UNBOUND_DRIVER, it removes the device
from its DMAR domain.
A hot added device will be added into an IOMMU domain when it first does IOMMU
op. So there is no need to add more code for hot add.
Without the patch, after a hot-remove, a hot-added device on the same
slot will not work.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The model for IOMMU passthrough is that decent devices that can cope
with DMA to all of memory get passthrough; crappy devices with a limited
dma_mask don't -- they get to use the IOMMU anyway.
This is done on the basis that IOMMU passthrough is usually wanted for
performance reasons, and it's only the decent PCI devices that you
really care about performance for, while the crappy 32-bit ones like
your USB controller can just use the IOMMU and you won't really care.
Unfortunately, the check for this was only looking at dev->dma_mask, not
at dev->coherent_dma_mask. And some devices have a 32-bit
coherent_dma_mask even though they have a full 64-bit dma_mask.
Even more unfortunately, fixing that simple oversight would upset
certain broken HP devices. Not only do they have a 32-bit
coherent_dma_mask, but they also have a tendency to do stray DMA to
unmapped addresses. And then they die when they take the DMA fault they
so richly deserve.
So if we do the 'correct' fix, it'll mean that affected users have to
disable IOMMU support completely on "a large percentage of servers from
a major vendor."
Personally, I have little sympathy -- given that this is the _same_
'major vendor' who is shipping machines which claim to have IOMMU
support but have obviously never _once_ booted a VT-d capable OS to do
any form of QA. But strictly speaking, it _would_ be a regression even
though it only ever worked by fluke.
For 2.6.33, we'll come up with a quirk which gives swiotlb support
for this particular device, and other devices with an inadequate
coherent_dma_mask will just get normal IOMMU mapping.
The simplest fix for 2.6.32, though, is just to jump through some hoops
to try to allocate coherent DMA memory for such devices in a place that
they can reach. We'd use dma_generic_alloc_coherent() for this if it
existed on IA64.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Chris Wright has some patches which let us fall back to swiotlb nicely
if IOMMU initialisation fails. But those are a bit much for 2.6.32.
Instead, let's shift the check for the biggest problem, the HP and Acer
BIOS bug which reports a DMAR at physical address zero. That one can
actually be checked much earlier -- before we even admit to having
detected an IOMMU in the first place. So the swiotlb init goes ahead as
we want.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Add an interface to lock/unlock an I2C bus segment
i2c-piix4: Modify code name SB900 to Hudson-2
* 'for-linus' of git://neil.brown.name/md:
md/raid5: make sure curr_sync_completes is uptodate when reshape starts
md: don't clear endpoint for resync when resync is interrupted.
KSM needs a cond_resched() for CONFIG_PREEMPT_NONE, in its unbounded
search of the unstable tree. The stable tree cases already have one,
and originally there was one down inside get_user_pages();
but I missed it when I converted to follow_page() instead.
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Acked-by: Izik Eidus <ieidus@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
nilfs2: fix missing cleanup of gc cache on error cases
nilfs2: fix kernel oops in error case of nilfs_ioctl_move_blocks
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
net/fsl_pq_mdio: add module license GPL
can: fix WARN_ON dump in net/core/rtnetlink.c:rtmsg_ifinfo()
can: should not use __dev_get_by_index() without locks
hisax: remove bad udelay call to fix build error on ARM
ipip: Fix handling of DF packets when pmtudisc is OFF
qlge: Set PCIe reset type for EEH to fundamental.
qlge: Fix early exit from mbox cmd complete wait.
ixgbe: fix traffic hangs on Tx with ioatdma loaded
ixgbe: Fix checking TFCS register for TXOFF status when DCB is enabled
ixgbe: Fix gso_max_size for 82599 when DCB is enabled
macsonic: fix crash on PowerBook 520
NET: cassini, fix lock imbalance
ems_usb: Fix byte order issues on big endian machines
be2net: Bug fix to send config commands to hardware after netdev_register
be2net: fix to set proper flow control on resume
netfilter: xt_connlimit: fix regression caused by zero family value
rt2x00: Don't queue ieee80211 work after USB removal
Revert "ipw2200: fix oops on missing firmware"
decnet: netdevice refcount leak
netfilter: nf_nat: fix NAT issue in 2.6.30.4+
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: Move of_set_property_mutex acquisition outside of devtree_lock grab.
sparc64: replace parentheses in pmul()
sparc64: Add a comment about why we only use certain memory barriers these days.
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: don't use CIFSGetSrvInodeNumber in is_path_accessible
cifs: clean up handling when server doesn't consistently support inode numbers
* 'sh/for-2.6.32' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Replace old style lock initializer
sh: Account for cache aliases in flush_icache_range()
sh: unwinder: Fix up invalid PC refetch in dwarf unwinder.
serial: sh-sci: disable callback typo fix
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: snd-aica: declare MODULE_FIRMWARE
ALSA: hda - Don't initialize CORB/RIRB for single_cmd mode
ALSA: usb-audio: fix combine_word problem
sound: Replace old style lock initializer
ASoC: S3C64XX I2S: Enable audio-bus clock
ASoC: OMAP: Don't try to set unsupported OMAP_DMA_DATA_BURST_16 on OMAP1
ALSA: hda, move hp_bseries_system
sound: Use KERN_WARNING instead of KERN_WARN, which does not exist
ALSA: intel8x0: Mute External Amplifier by default for another Sony model
ALSA: hda - Add OLPC XO-1.5 PCI ID
ALSA: hda - Enable GPIO control for mute LED on HP systems
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: sleep: another HP/Compaq DMI entries for init_set_sci_en_on_resume
ACPI: add DMI entry for SCI_EN resume quirk on HP dv4
thermal: sysfs-api.txt - document passive attribute for thermal zones
thermal: sysfs-api.txt - reformat for improved readability
acpi: thermal: Add EOL to the trip_point_N_type strings
ACPI: Move dereference after NULL test
ACPICA: avoid "Info: mapping multiple BARs. Your kernel is fine."
ACPI: add __cpuinit to acpi_processor_add()
acpi-power-meter: Don't leak ACPI error codes to userspace
eeepc-laptop: don't enable camera at startup if it's already on.
Revert "eeepc-laptop: Prevent a panic when disabling RT2860 wireless when associated"
ACPI: clean up video.c boundary checks and types
SPIN_LOCK_UNLOCKED is deprecated. Use __SPIN_LOCK_UNLOCKED instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The icache may also contain aliases so we must account for them just
like we do when manipulating the dcache. We usually get away with
aliases in the icache because the instructions that are read from memory
are read-only, i.e. they never change. However, the place where this
bites us is when the code has been modified.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes an -rc1 regression brought by the commit:
1cf58fa840 ("nilfs2: shorten freeze
period due to GC in write operation v3").
Although the patch moved out a function call of
nilfs_ioctl_move_blocks() to nilfs_ioctl_clean_segments() from
nilfs_ioctl_prepare_clean_segments(), it didn't move corresponding
cleanup job needed for the error case.
This will move the missing cleanup job to the destination function.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Acked-by: Jiro SEKIBA <jir@unicus.jp>
This fixes a kernel oops reported by Markus Trippelsdorf in the email
titled "[NILFS users] kernel Oops while running nilfs_cleanerd".
The oops was caused by a bug of error path in
nilfs_ioctl_move_blocks() function, which was inlined in
nilfs_ioctl_clean_segments().
nilfs_ioctl_move_blocks checks duplication of blocks which will be
moved in garbage collection. But, the check should have be done
within nilfs_ioctl_move_inode_block() to prevent list corruption among
buffers storing the target blocks.
To fix the kernel oops, this moves forward the duplication check
before the list insertion.
I also tested this for stable trees [2.6.30, 2.6.31].
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: stable <stable@kernel.org>
or it will taint the kernel and fail to load becuase
of_address_to_resource() is GPL only.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On older kernels, e.g. 2.6.27, a WARN_ON dump in rtmsg_ifinfo()
is thrown when the CAN device is registered due to insufficient
skb space, as reported by various users. This patch adds the
rtnl_link_ops "get_size" to fix the problem. I think this patch
is required for more recent kernels as well, even if no WARN_ON
dumps are triggered. Maybe we also need "get_xstats_size" for
the CAN xstats.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_proc_getifname() is called with RTNL and dev_base_lock
not held. It calls __dev_get_by_index() without locks, and
this is illegal (might crash)
Close the race by holding dev_base_lock and copying dev->name
in the protected section.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
`>>' has a higher precedence than `?' so src2 evaluated to
either 16 or 0 dependent on the bits set in rs2.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers need to be able to prevent access to an I2C bus segment
for a specific period of time. Add an interface for them to do so
without twiddling with i2c-core internals.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
So far, CORB/RIRB still remains even if the driver is switched to the
single_cmd mode. The specification says that this should be disabled,
but I hoped this isn't the case; indeed most devices worked together with
CORB/RIRB.
However, Poulsbo (US15W) seems problematic with this setup, and it
requires to disable CORB/RIRB when single_cmd is used.
Now this patch disables CORB/RIRB initialization when the single_cmd
mode is used. Also the unsolicited event is disabled because it can't
work without RIRB.
Reported-and-tested-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix combine_word problem where first octet is not
read properly. The only affected place seems to be the
INPUT_TERMINAL type. Before now, sound controls can be created
with the output terminal's name which is a fallback mechanism
used only for unknown input terminal types. For example,
Line can wrongly appear as Speaker. After the change it
should appear as Line.
The side effect of this change can be that users
can expect the wrong control name in their scripts or
programs while now we return the correct one.
Probably, these defines should use get_unaligned_le16 and
friends.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SPIN_LOCK_UNLOCKED is deprecated. Use __SPIN_LOCK_UNLOCKED instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hisax ISDN driver fails to build on ARM with CONFIG_HISAX_ELSA:
| drivers/built-in.o: In function `modem_set_dial':
| drivers/isdn/hisax/elsa_ser.c:535: undefined reference to `__bad_udelay'
| drivers/isdn/hisax/elsa_ser.c:544: undefined reference to `__bad_udelay'
| drivers/built-in.o: In function `modem_set_init':
| drivers/isdn/hisax/elsa_ser.c:486: undefined reference to `__bad_udelay'
| [...]
According to the comment in arch/arm/include/asm/delay.h, __bad_udelay
is specifically designed on ARM to produce a build failure when udelay
is called with a value > 2000.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 2003 requires the outer header to have DF set if DF is set
on the inner header, even when PMTU discovery is off for the
tunnel. Our implementation does exactly that.
For this to work properly the IPIP gateway also needs to engate
in PMTU when the inner DF bit is set. As otherwise the original
host would not be able to carry out its PMTU successfully since
part of the path is only visible to the gateway.
Unfortunately when the tunnel PMTU discovery setting is off, we
do not collect the necessary soft state, resulting in blackholes
when the original host tries to perform PMTU discovery.
This problem is not reproducible on the IPIP gateway itself as
the inner packet usually has skb->local_df set. This is not
correctly cleared (an unrelated bug) when the packet passes
through the tunnel, which allows fragmentation to occur. For
hosts behind the IPIP gateway it is readily visible with a simple
ping.
This patch fixes the problem by performing PMTU discovery for
all packets with the inner DF bit set, regardless of the PMTU
discovery setting on the tunnel itself.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device requires a fundamental reset when recovering from EEH.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This line was accidentally left out of the previous commit #
da03945140 ("qlge: Fix firmware mailbox
command timeout.").
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ioatdma was loaded we we were unable to transmit traffic. We weren't
using the correct registers in ixgbe_update_tx_dca for 82599 systems.
Likewise in ixgbe_configure_tx() we weren't disabling the arbiter before
modifying MTQC.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When DCB is enabled, the ixgbe_check_tx_hang() should check the corresponding
TC's TXOFF in TFCS based on the TC that the tx ring belongs to. Adds a
function to map from the tx_ring hw reg_idx to the correspodning TC and read
TFCS accordingly.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 32k gso_max_size when DCB is enabled is for 82598 only, not for 82599.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No-one seems to know where the PowerBook 500 series store their ethernet
MAC addresses. So, rather than crash, use a MAC address from the SONIC
CAM. Failing that, generate a random one.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanse found that one error path in cas_open omits to unlock pm_mutex.
Fix that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPC-USB is using a ARM7 core with little endian byte order. The "id" field
in can_msg needs byte order conversion from/to CPU byte order.
Signed-off-by: Sebastian Haas <haas@ems-wuensche.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sending config commands to be2 hardware before netdev_register is
completed, is sometimes causing the async link notification to arrive
even before the driver is ready to handle it. The commands for vlan
config and flow control settings can infact wait till be_open.
This patch takes care of that.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If be2 goes into suspend after a user changes the flow control settings,
we are not programming them back after resume. This patch takes care of it.
We now get the flow control settings before going to suspend mode and
then apply them during resume.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit v2.6.28-rc1~717^2~109^2~2 was slightly incomplete; not all
instances of par->match->family were changed to par->family.
References: http://bugzilla.netfilter.org/show_bug.cgi?id=610
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because it's lighter weight, CIFS tries to use CIFSGetSrvInodeNumber to
verify the accessibility of the root inode and then falls back to doing a
full QPathInfo if that fails with -EOPNOTSUPP. I have at least a report
of a server that returns NT_STATUS_INTERNAL_ERROR rather than something
that translates to EOPNOTSUPP.
Rather than trying to be clever with that call, just have
is_path_accessible do a normal QPathInfo. That call is widely
supported and it shouldn't increase the overhead significantly.
Cc: Stable <stable@kernel.org>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
It's possible that a server will return a valid FileID when we query the
FILE_INTERNAL_INFO for the root inode, but then zeroed out inode numbers
when we do a FindFile with an infolevel of
SMB_FIND_FILE_ID_FULL_DIR_INFO.
In this situation turn off querying for server inode numbers, generate a
warning for the user and just generate an inode number using iunique.
Once we generate any inode number with iunique we can no longer use any
server inode numbers or we risk collisions, so ensure that we don't do
that in cifs_get_inode_info either.
Cc: Stable <stable@kernel.org>
Reported-by: Timothy Normand Miller <theosib@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
This prevents the rt2x00 driver from queueing ieee80211 work after the
USB card has been removed, preventing a kernel panic.
Signed-off-by: Sean Cross <sean@chumby.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>