Add support for ISO/IEC 15693 RF technology and Type 5 tags.
Note that Type 5 tags used to be referred to as Type V tags.
CC: Erick Macias <emacias@ti.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for Type 4A Tags which includes
supporting the underlying ISO/IEC 14443-A
protocol.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add a driver for the Texas Instruments TRF7970a RFID/NFC/15693
transceiver. The driver currently supports ISO/IEC 14443 Type 2
tags only (MIFARE Ultralight and Ultralight C but not Classic).
CC: Erick Macias <emacias@ti.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
According to the latest draft specification from
the NFC-V committee, ISO/IEC 15693 tags will be
referred to as "Type 5" tags and not "Type V"
tags anymore. Make the code reflect the new
terminology.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This ensures we won't add polling function to the table of polling technologies
for non-supported protocols.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
nfc_find_se() does not modify any list entry while iterating the list.
So use list_for_each_entry instead of list_for_each_entry_safe.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Calling init_completion() once is enough.
Then use reinit_completion() instead in __nci_request() and nci_spi_send().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes a memory leak issue that may occur if data sending fails in
initiator mode. The data_exch structure was not released in case of
error.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There was a missing break making the digital stack configured for
ISO1443 target instead of ISO15693.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds support for ISO-DEP protocol over NFC-A rf technology. The
port100 already supports NFC-A and ATS request and response for type 4A
tags are handled at digital level. This patch adds NFC_PROTO_ISO14443
to the supported protocols and an entry for framing configuration which
is the same as NFC-A standard frame with CRC handling.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When a type 4A target is activated, this change adds the ISO-DEP SoD
when sending frames and removes it when receiving responses. Chaining
is not supported so sent frames are rejected if they exceed remote FSC
bytes.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds support for ATS request and response handling for type 4A tag
activation.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The arrays for protocols and rf techs must define a number of entries
corresponding to their maximum possible index values.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
PN544 C3 firmwares already contain the command frames to be sent, but as
they may exceed the i2c maximum payload, we need to fragment them into
secure chunks and send them through the secure write command.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Different pn544 hardware variant may use different commands to download
new firmwares. The C2 does a regular firmware download while the C3 uses
a more secure protocol.
As a consequence we need to pass the hardware variant from the HCI SW
version command reply down to the pn544 i2c layer, in order to use the
right protocol at run time.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add ISO/IEC 15693 support by having netlink push the
1-byte DSFID and 8-byte UID tag information upstream.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for ISO/IEC 15693 to the digital layer. The code
currently uses single-slot anticollision only since the digital
layer infrastructure only supports one tag per adapter (making
it pointless to do 16-slot anticollision).
The code uses two new framing types:
'NFC_DIGITAL_FRAMING_ISO15693_INVENTORY' and
'NFC_DIGITAL_FRAMING_ISO15693_TVT'. The former is used to
tell the driver to prepare for an Inventory command and the
ensuing anticollision sequence. The latter is used to tell
the driver that the anticollision sequence is over and to
prepare for non-inventory commands.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add the header definitions required by upcoming
patches that add support for ISO/IEC 15693.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The dtim period sent to FW was 0 because the dtim period
was never set. This caused an incorrect dtim count to be sent in
beacons.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes problems seen with multiple softap clients and reconnecting
softap clients.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is more line with the names of the other members
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3680 has a few registers on other addresses.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After fw caps exchange, print the FW's capabilities.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If wowlan if off mac80211 will stop / start the driver on suspend /
resume. This causes problems on resume since request_firmware is called
from start. Fix this by caching the nv.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some wcnss firmwares the start command can take up to 300ms to
complete. Currently there is a 200ms timeout for SMD command to
complete which causes the start to fail.
Increase the timeout to 500ms. Also improve debug information
regarding SMD command completion time.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Response format is not in the canonical format.
wcn36xx_smd_rsp_status_check cannot be used.
* Save the FW caps in wcn36xx struct for later use.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TI wl12xx/wl18xx cards support channel switch via a driver specific
switch_channel op while operating with channel contexts.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enabling beacon filtering before receving a beacon
might result in not having a beacon at all for the
current connected AP, which prevents the station
from entering power-save.
Replace the current approach (of starting beacon
filtering on init) and configure beacon filering
only after bss_conf->dtimper is set (which means
mac80211 already parsed a beacon).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dfs configuration command might take longer than
the current timeout. increase it to 5 seconds.
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Silently ignore repetitive scheduling of recovery work and commands
being passed to the bus when the HW is not available. This can happen
many times during recovery and slow it down. It also spams the kernel
logs.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each AP has its own global and broadcast links, so when
checking for active sta count (according to the active_link_count)
we must take them all into account.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 unsets the default wep key on disassoc.
The fw doesn't support this notification, so simply
ignore it.
The actual flow actually triggers fw recovery in some
cases, as mac80211 unsets the default key only after
disassoc, when wlvif->sta.hlid, resulting in invalid
hlid being passed to the fw.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12xx chips allow only OFDM rates in AP mode for BT-Coex purposes. This
is no longer required in 18xx chips, starting with FW 8.6.0.0.8.
Update the min allowed FW version in 18xx to support this functionality.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stopping sched scan on interface removal (during recovery)
is no longer needed, as sched scanning is automatically
restarted by mac80211.
Signed-off-by: Barak Bercovitz <barak@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send EAPOL frames with voice priority by setting (the new)
TX_HW_ATTR_EAPOL_FRAME bit in tx attribute.
Sending EAPOL with voice priority fixes re-key
timeout issues during heavy traffic.
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bump the min wl18xx fw version to 8.8.0.0.13
This fw is not backward compatible with older
firmware (due to api changes), so use bump
the firmware name as well.
Some modifications were done to the driver-fw api
in order to support multiple APs.
Additionally, some of the consts (such as max stations,
max links and max RX BA sessions) were changed.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each hw supports a different iface combinations.
Define the supported combinations in each driver,
and save it in wl->iface_combinations.
Since each driver defines its own combinations now,
it can also define its max supported channels, so
we no longer need to save and set it explicitly
in wlcore.
Update wl18xx interface combinations to allow
multiple APs.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each hw supports a different max stations (connected to the
same ap). add a new wl->max_ap_stations and use it instead
of the current common AP_MAX_STATIONS.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upcoming fw versions will have different max links support
(according to the hw). Get ready for it by configuring
wl->num_links per-hw, instead of using the const WL12XX_MAX_LINKS.
However, continue using WLCORE_MAX_LINKS in order to simplify
structs declarations (we use it in multiple bitmaps, and converting
them to dynamic arrays is just cumbersome).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of splitting the fw_status into 2 and using some
complex calculations, read the fw status and let each low-level
driver (wl12xx/wl18xx) convert it into a common struct.
This is required for the upcoming fw api changes, which
break the current logic anyway.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems the wl18xx FW sometimes sends spurious changes on the PSM state
of the broadcast HLID. This causes us to search for a station on a
non-peer link and fail, causing warnings in our log.
Prevent the driver from considering PSM changes for any non-peer HLIDs.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the chip is in ELP mode read/write to FW is invalid and may cause
the lower layers to get stuck. The reads/writes concerning ELP wakeup
are the exception here and are checked for. In addition to blocking the
IO, produce a warning.
Signed-off-by: Barak Bercovitz <barak@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes a tx_flush during suspend fails, but the FW manages to flush
out the packets during the time when the host is supsended. Cancel
the Tx-watchdog on suspend to not cause a spurious recovery on resume
for that case. Set a flag to reinit the watchdog on the first Tx after
resume, so we'll still recover if the FW is not empty and there's
indeed a problem.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zero rx_filter_enabled array after recovery to avoid
cases were the driver will keep trying to clear a
filter which is not configured in FW.
Such case will cause consecutive recoveries due to
command execution failures.
While on it, convert rx_filter_enabled to bitmap,
to save some memory and make sparse happy (it
doesn't like sizeof(bool array)).
Signed-off-by: Nadim Zubidat <nadimz@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ieee80211_channel_to_frequency() to replace b43_channel_to_freq_{2,5}ghz(),
and remove unused b43_freq_to_channel_{2,5}ghz().
Signed-off-by: ZHAO Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>