This change allows userspace to register for probe request
frames on an IBSS interface. Userspace then has to handle
them and send replies.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add some information that we have about VHT to radiotap.
This at least lets one see the MCS and NSS information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.
Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the cipher suites need to be allocated, but this
allocation fails, this leaks the internal scan request.
Fix that by going to the correct error handling label.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even before channel contexts/multi-channel, having a
single global TX power limit was already problematic,
in particular if two managed interfaces connected to
two APs with different power constraints. The channel
context introduction completely broke this though and
in fact I had disabled TX power configuration there
for drivers using channel contexts.
Change everything to track TX power per interface so
that different user settings and different channel
maxima are treated correctly. Also continue tracking
the global TX power though for compatibility with
applications that attempt to configure the wiphy's
TX power globally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
WDS is (currently) not allowed when channel
contexts are *supported*, not when they're
*not* supported. Fix the inverted test.
Reported-by: Ronald <ronald645@gmail.com>
Tested-by: Ronald <ronald645@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the user wants to scan using a vif configured as AP,
cfg80211 must give him a chance to do it, even if this
will disrupt the stations performance due to off-channel
scanning. To do so, this patch adds a 'force' flag to the
SCAN_TRIGGER command which tells cfg80211 to perform the
scanning operation even if the vif is an AP and the
beaconing has already started.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use NL80211_SCAN_FLAG_LOW_PRIORITY flag in mac80211's scan state
machine to prematurely terminate scan operations if outbound
traffic collides. This is useful for marking background scans so
they don't affect throughput.
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
[set feature flag only if software scan is used]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The next patch will introduce a flag that is set
by default in cfg80211 so drivers and mac80211
need to use |= to set features they have so that
they don't clear the already-set feature.
We could set the flag in wiphy_register() instead
of wiphy_new() to avoid this patch, but then the
drivers couldn't *unset* flags they don't want to
use even though the implementation is generic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rename struct ieee80211_vht_capabilities to ieee80211_vht_cap
and renamed its member vht_capabilities_info to vht_cap_info.
Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SAE uses two rounds of Authentication frames and both rounds require
considerable calculation to be done. This commit extends the existing
station mode authentication request to allow more control for user
space programs to build the SAE fields and to run the authentication
step ones. Only the second round with authentication transaction
sequence 2 will result in moving to authenticated state.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On each channel that the device is operating on, it
may need to listen using one or more chains depending
on the SMPS settings of the interfaces using it. The
previous channel context changes completely removed
this ability (before, it was available as the SMPS
mode).
Add per-context tracking of the required static and
dynamic RX chains and notify the driver on changes.
To achieve this, track the chains and SMPS mode used
on each virtual interface and update the channel
context whenever this changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of operating on a single channel only,
use the new channel context infrastructure in
all mac80211 code.
This enables drivers that want to use the new
channel context infrastructure to use multiple
channels, while nothing should change for all
the other drivers that don't support it.
Right now this disables both TX power settings
and spatial multiplexing powersave. Both need
to be re-enabled on a channel context basis.
Additionally, when channel contexts are used
drop the connection when channel switch is
received rather than trying to handle it. This
will have to be improved later.
[With fixes from Eliad and Emmanuel incorporated]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on the driver, channel contexts may be used or
not. If they are used, the driver must have support for
hardware scan and remain-on-channel; otherwise the driver
must not advertise support for multiple channels.
Also prohibit WDS type interfaces when channel contexts
are to be used as there's no clear definition of which
channel they use.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel context are the foundation for multi-channel
operation. They are are immutable and are re-created
(or re-used if other interfaces are bound to a certain
channel and a compatible channel type) on channel
switching.
This is an initial implementation and more features
will come in separate patches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[some changes including RCU protection]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, mac80211 uses the power constraint IE, and reduces
the regulatory max TX power by it. This can cause issues if
the AP is advertising a large power constraint value matching
a high TX power in its country IE, for example in this case:
...
Country: US Environment: Indoor/Outdoor
...
Channels [157 - 157] @ 30 dBm
...
Power constraint: 13 dB
...
What happened here is that our local regulatory TX power is
15 dBm, and gets reduced by 13 dB so we end up with only
2 dBm effective TX power, which is way too low.
Instead, handle the country IE/power constraint IE combined
and restrict our TX power to the max of the regulatory power
and the maximum power advertised by the AP, in this case
17 dBm (= 30 dBm - 13 dB).
Also print a message when this happens to let the user know
and help us debug issues with it.
Reported-by: Carl A. Cook <CACook@quantum-equities.com>
Tested-by: Carl A. Cook <CACook@quantum-equities.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After cfg80211 got a P2P Device abstraction, add
support to mac80211. Whether it really is supported
or not will depend on whether or not the driver has
support for it, but mac80211 needs to change to be
able to support drivers that need a P2P Device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of tracking whether or not we're in a
scheduled scan, track the virtual interface
(sdata) in an RCU-protected pointer to make it
usable from RX to check the MAC address.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The implementation of tx_frags is buggy due to
not handling queue stop, and there's no driver
implementing it so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When CONFIG_PM is disabled, no device can possibly
support WoWLAN since it can't go to sleep to start
with. Due to this, mac80211 had even rejected the
hardware registration. By making all the code and
data for WoWLAN depend on CONFIG_PM we can promote
this runtime error to a compile-time error.
Add #ifdef around all WoWLAN code to remove it in
systems that don't need it as they never suspend.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set the necessary flags to allow user space applications
to register for authentication frames on IBSS interfaces.
This is useful for situations where userspace applications
want to control key negotiation between stations.
Signed-off-by: Will Hawkins <hawkinsw@opentechinstitute.org>
[reword commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While HW reconfig is in progress, drop all incoming Rx. This prevents
incoming packets from changing the internal state of the driver or
calling callbacks of the low level driver while it is in inconsistent
state.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Redesign all the off-channel code, getting rid of
the generic off-channel work concept, replacing
it with a simple remain-on-channel list.
This fixes a number of small issues with the ROC
implementation:
* offloaded remain-on-channel couldn't be queued,
now we can queue it as well, if needed
* in iwlwifi (the only user) offloaded ROC is
mutually exclusive with scanning, use the new
queue to handle that case -- I expect that it
will later depend on a HW flag
The bigger issue though is that there's a bad bug
in the current implementation: if we get a mgmt
TX request while HW roc is active, and this new
request has a wait time, we actually schedule a
software ROC instead since we can't guarantee the
existing offloaded ROC will still be that long.
To fix this, the queuing mechanism was needed.
The queuing mechanism for offloaded ROC isn't yet
optimal, ideally we should add API to have the HW
extend the ROC if needed. We could add that later
but for now use a software implementation.
Overall, this unifies the behaviour between the
offloaded and software-implemented case as much
as possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Low level drivers can now set certain netdev feature bits in
netdev_features member of the ieee80211_hw struct. These will be
propagated to every netdev created from this HW.
The white-listed features currently include only ones related to HW
checksumming.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a flag for the HT format (mixed vs. greenfield)
to allow drivers to report that on receive. Not all
drivers will do that though, so allow drivers to set
which radiotap MCS details they report.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This based on an idea posted by Stanislaw Gruszka,
though I accept full blame for the implementation!
This has been tested with ath9k.
The idea is to let users scan on the current operating
channel without interrupting normal traffic more than
absolutely necessary (changing power level might reset
some hardware, for instance).
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 currently only supports one hardware queue
per AC. This is already problematic for off-channel
uses since if we go off channel while the BE queue
is full and then try to send an off-channel frame
the frame will never go out. This will become worse
when we support multi-channel since then a queue on
one channel might be full, but we have to stop the
software queue for all channels. That is obviously
not desirable.
To address this problem allow drivers to register
more hardware queues, and allow them to map them to
virtual interfaces. When they stop a hardware queue
the corresponding AC software queues on the correct
interfaces will be stopped as well. Additionally,
there's an off-channel queue to solve that problem
and a per-interface after-DTIM beacon queue. This
allows drivers to manage software queues closer to
how the hardware works.
Currently, there's a limit of 16 hardware queues.
This may or may not be sufficient, we can adjust it
as needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not all devices are really capable of implementing
remain-on-channel, even if it is implemented in SW,
as they can't necessarily deal with channel changes
while associated.
Remove the WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL and add
it only if either the driver has remain_on_channel
implemented in the driver/device.
Also add it to all drivers that advertise P2P right
now since those definitely have to have it working.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The on-oper-channel optimization was reverted,
so remove the outdated comment as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
uapsd_queues and uapsd_max_sp_len are relevant only for managed
interfaces, and can be configured differently for each vif.
Move them from the local struct to sdata->u.mgd, and update
the debugfs functions accordingly.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
That's a lot longer than open-coding it and
doesn't really add value, so just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
read_lock(&tpt_trig->trig.leddev_list_lock) is accessed via the path
ieee80211_open (->) ieee80211_do_open (->) ieee80211_mod_tpt_led_trig
(->) ieee80211_start_tpt_led_trig (->) tpt_trig_timer before initializing
it.
the intilization of this read/write lock happens via the path
ieee80211_led_init (->) led_trigger_register, but we are doing
'ieee80211_led_init' after 'ieeee80211_if_add' where we
register netdev_ops.
so we access leddev_list_lock before initializing it and causes the
following bug in chrome laptops with AR928X cards with the following
script
while true
do
sudo modprobe -v ath9k
sleep 3
sudo modprobe -r ath9k
sleep 3
done
BUG: rwlock bad magic on CPU#1, wpa_supplicant/358, f5b9eccc
Pid: 358, comm: wpa_supplicant Not tainted 3.0.13 #1
Call Trace:
[<8137b9df>] rwlock_bug+0x3d/0x47
[<81179830>] do_raw_read_lock+0x19/0x29
[<8137f063>] _raw_read_lock+0xd/0xf
[<f9081957>] tpt_trig_timer+0xc3/0x145 [mac80211]
[<f9081f3a>] ieee80211_mod_tpt_led_trig+0x152/0x174 [mac80211]
[<f9076a3f>] ieee80211_do_open+0x11e/0x42e [mac80211]
[<f9075390>] ? ieee80211_check_concurrent_iface+0x26/0x13c [mac80211]
[<f9076d97>] ieee80211_open+0x48/0x4c [mac80211]
[<812dbed8>] __dev_open+0x82/0xab
[<812dc0c9>] __dev_change_flags+0x9c/0x113
[<812dc1ae>] dev_change_flags+0x18/0x44
[<8132144f>] devinet_ioctl+0x243/0x51a
[<81321ba9>] inet_ioctl+0x93/0xac
[<812cc951>] sock_ioctl+0x1c6/0x1ea
[<812cc78b>] ? might_fault+0x20/0x20
[<810b1ebb>] do_vfs_ioctl+0x46e/0x4a2
[<810a6ebb>] ? fget_light+0x2f/0x70
[<812ce549>] ? sys_recvmsg+0x3e/0x48
[<810b1f35>] sys_ioctl+0x46/0x69
[<8137fa77>] sysenter_do_call+0x12/0x2
Cc: <stable@vger.kernel.org>
Cc: Gary Morain <gmorain@google.com>
Cc: Paul Stewart <pstew@google.com>
Cc: Abhijit Pradhan <abhijit@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, mac80211 goes to idle-off before starting a scan.
However, some devices that implement hw scan might not
need going idle-off in order to perform a hw scan, and
thus saving some energy and simplifying their state machine.
(Note that this is also the case for sched scan - it
currently doesn't make mac80211 go idle-off)
Add a new flag to indicate support for hw scan while idle.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the second part of the auth/assoc redesign,
the mac80211 part. This moves the auth/assoc code
out of the work abstraction and into the MLME, so
that we don't flip channels all the time etc.
The only downside is that when we are associated,
we need to drop the association in order to create
a connection to another AP, but for most drivers
this is actually desirable and the ability to do
was never used by any applications. If we want to
implement resource reservation with FT-OTA, we'd
probably best do it with explicit R-O-C in wpa_s.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(based on Eliad's patch)
Add a callback to notify the low-level driver whenever
the state of a station changes. The driver is only
notified when the station is actually in the mac80211
hash table, not for pre-insert state transitions.
To allow the driver to replace sta_add/remove calls
with this, call extra transitions with the NOTEXIST
state.
This callback can fail, so we need to be careful in
handling it when a station is inserted, particularly
in the IBSS case where we still keep the station entry
around for mac80211 purposes.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The local maximum transmit power for a channel is defined as the maximum
regulatory transmission power minus the local power constraint specified
for the channel in the Power Constraint element. (7.3.2.15 IEEE80211 2007)
Signed-off-by: Hong Wu <hong.wu@dspg.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ip address of the vif can be set even before the
vif is up. requiring the vif to be up in the vif
notifier makes the notifer ignore this event, which
causes wrong arp filter configuration later on.
Reported-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_configure_filter code used local->scanning as a boolean
value when it was a bit mask. Bits SCAN_COMPLETED, SCAN_ABORTED
should not set FIF_BCN_PRBRESP_PROMISC filter.
SCAN_HW_SCANNING should not set FIF_BCN_PRBRESP_PROMISC either,
as there is no explicit filter configuration request from
scan code. If a driver requires FIF_BCN_PRBRESP_PROMISC mode
during HW scanning, it's up to the driver to temporary enable it.
Similar mistake was fixed also in ieee80211_hw_config (power
configuration code).
Verified-by: Vitaly Wool <vitaly.wool@sonyericsson.com>
Signed-off-by: Dmitry Tarnyagin <dmitry.tarnyagin@stericsson.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HT mode is set by iw (previous patchsets).
The interface is set into the specified HT mode.
HT mode and capabilities are announced in beacons.
If we add a station that uses HT also, the fastest matching HT mode will
be used for transmission. That means if we are using HT40+ and we add a station
running on HT40-, we would transfer at HT20.
If we join an IBSS with HT40, but the secondary channel is not
available, we will fall back into HT20 as well.
Allow frame aggregation to start in IBSS mode.
Signed-off-by: Alexander Simon <an.alexsimon@googlemail.com>
[siwu@hrz.tu-chemnitz.de: Updates]
* remove implicit channel_type enum assumptions
* use rate_control_rate_init() if channel type changed
* remove channel flags check
* activate HT IBSS feature support
* slightly reword commit message
* rebase on wireless-testing
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The on-channel work optimisations have caused a
number of issues, and the code is unfortunately
very complex and almost impossible to follow.
Instead of attempting to put in more workarounds
let's just remove those optimisations, we can
work on them again later, after we change the
whole auth/assoc design.
This should fix rate_control_send_low() warnings,
see RH bug 731365.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville
Antonio Quartulli
Johannes Berg
Antonio Quartulli
Sam Leffler
Mahesh Palivela
Jouni Malinen
Michal Kazior
Will Hawkins
Arik Nemtsov
Ben Greear
Eliad Peller
Mohammed Shafi Shajakhan
Hong Wu
Dmitry TARNYAGIN
Alexander Simon