Commit Graph

1613 Commits

Author SHA1 Message Date
Anton Vorontsov 4538d0ca71 powerpc: Fix no interrupt handling in pata_of_platform
When no interrupt is specified the pata_of_platform fills the irq_res
resource with -1, which is wrong to do for two reasons:

1. By definition, 'no irq' should be IRQ 0, not some negative integer;
2. pata_platform checks for irq_res.start > 0, but since irq_res.start
   is unsigned type, the check will be true for `-1'.

Reported-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2008-10-10 15:55:17 +11:00
Jens Axboe 8bff7c6b0f libata: set queue SSD flag for SSD devices
SSD devices should give an RPM setting of 1 in word 217 of the ID
page. If we see such a device, tell the block layer about it.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:19 +02:00
Jens Axboe 242f9dcb8b block: unify request timeout handling
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.

Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.

Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:13 +02:00
Seth Heasley 0395e61bab ata_piix: IDE Mode SATA patch for Intel Ibex Peak DeviceIDs
This patch updates the Intel Ibex Peak (PCH) IDE mode SATA Controller DeviceIDs.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:29:12 -04:00
Tejun Heo 11fc33da8d libata-eh: clear UNIT ATTENTION after reset
Resets make ATAPI devices raise UNIT ATTENTION which fails the next
command.  As resets can happen asynchronously for unrelated reasons,
this sometimes disrupts innocent users.  For example, reading DVD
fails after the system wakes up from suspend or the other device
sharing the channel went through bus error.

Clearing UA has some problems as it might clear UA which the userland
needs to know about.  However, UA after resets can only be about the
reset itself and benefits of clearing it overweights cons.  Missing UA
can only delay failure to one of the following commands anyway.  For
example, timeout while burning is in progress will trigger reset and
reset the device state and probably corrupt the burning run.  Although
the userland application won't get the UA, its pending writes will
fail.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:29:06 -04:00
Herton Ronaldo Krzesinski d09addf65c ata_piix: add Hercules EC-900 mini-notebook to ich_laptop short cable list
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:28:40 -04:00
Sonic Zhang 67e3e221d6 [libata] pata_bf54x: Add proper PM operation
[akpm@linux-foundation.org: remove ifdefs, make things static]
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:28:29 -04:00
Kumar Gala 47d692a946 pata_sil680: convert CONFIG_PPC_MERGE to CONFIG_PPC
Now that arch/ppc is dead CONFIG_PPC_MERGE is always defined for all
powerpc platforms and we want to get rid of CONFIG_PPC_MERGE use
CONFIG_PPC instead.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:28:02 -04:00
Elias Oltmanns 45fabbb77b libata: Implement disk shock protection support
On user request (through sysfs), the IDLE IMMEDIATE command with UNLOAD
FEATURE as specified in ATA-7 is issued to the device and processing of
the request queue is stopped thereafter until the specified timeout
expires or user space asks to resume normal operation. This is supposed
to prevent the heads of a hard drive from accidentally crashing onto the
platter when a heavy shock is anticipated (like a falling laptop
expected to hit the floor). In fact, the whole port stops processing
commands until the timeout has expired in order to avoid any resets due
to failed commands on another device.

Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:27:54 -04:00
Ben Dooks 2ad69677b6 PATA: RPC now selects HAVE_PATA_PLATFORM for pata platform driver
The RPC machine type now selects HAVE_PATA_PLATFORM so we can remove
the special case in the PATA_PLATFORM configuration code.

Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:25:43 -04:00
Tejun Heo be77e43abb ata_piix: drop merged SCR access and use slave_link instead
Now that libata has slave_link, there's no need to keep ugly merged
SCR access.  Drop it and use slave_link instead.  This results in
simpler code and much better separate link handling for master and
slave.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:25:32 -04:00
Tejun Heo b1c72916ab libata: implement slave_link
Explanation taken from the comment of ata_slave_link_init().

 In libata, a port contains links and a link contains devices.  There
 is single host link but if a PMP is attached to it, there can be
 multiple fan-out links.  On SATA, there's usually a single device
 connected to a link but PATA and SATA controllers emulating TF based
 interface can have two - master and slave.

 However, there are a few controllers which don't fit into this
 abstraction too well - SATA controllers which emulate TF interface
 with both master and slave devices but also have separate SCR
 register sets for each device.  These controllers need separate links
 for physical link handling (e.g. onlineness, link speed) but should
 be treated like a traditional M/S controller for everything else
 (e.g. command issue, softreset).

 slave_link is libata's way of handling this class of controllers
 without impacting core layer too much.  For anything other than
 physical link handling, the default host link is used for both master
 and slave.  For physical link handling, separate @ap->slave_link is
 used.  All dirty details are implemented inside libata core layer.
 From LLD's POV, the only difference is that prereset, hardreset and
 postreset are called once more for the slave link, so the reset
 sequence looks like the following.

 prereset(M) -> prereset(S) -> hardreset(M) -> hardreset(S) ->
 softreset(M) -> postreset(M) -> postreset(S)

 Note that softreset is called only for the master.  Softreset resets
 both M/S by definition, so SRST on master should handle both (the
 standard method will work just fine).

As slave_link excludes PMP support and only code paths which deal with
the attributes of physical link are affected, all the changes are
localized to libata.h, libata-core.c and libata-eh.c.

 * ata_is_host_link() updated so that slave_link is considered as host
   link too.

 * iterator extended to iterate over the slave_link when using the
   underbarred version.

 * force param handling updated such that devno 16 is mapped to the
   slave link/device.

 * ata_link_on/offline() updated to return the combined result from
   master and slave link.  ata_phys_link_on/offline() are the direct
   versions.

 * EH autopsy and report are performed separately for master slave
   links.  Reset is udpated to implement the above described reset
   sequence.

Except for reset update, most changes are minor, many of them just
modifying dev->link to ata_dev_phys_link(dev) or using phys online
test instead.

After this update, LLDs can take full advantage of per-dev SCR
registers by simply turning on slave link.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:25:28 -04:00
Tejun Heo b5b3fa386b libata: misc updates to prepare for slave link
* Add ATA_EH_ALL_ACTIONS.

* Make sata_link_{on|off}_line() return bool instead of int.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:22:32 -04:00
Tejun Heo aadffb682c libata: reimplement link iterator
Implement __ata_port_next_link() and reimplement
__ata_port_for_each_link() and ata_port_for_each_link() using it.
This removes relatively large inlined code and makes iteration easier
to extend.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:22:30 -04:00
Tejun Heo 82ef04fb4c libata: make SCR access ops per-link
Logically, SCR access ops should take @link; however, there was no
compelling reason to convert all SCR access ops when adding @link
abstraction as there's one-to-one mapping between a port and a non-PMP
link.  However, that assumption won't hold anymore with the scheduled
addition of slave link.

Make SCR access ops per-link.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:22:28 -04:00
Tejun Heo 4c1eb90a09 sata_nv: reinstate nv_hardreset() for non generic controllers
Commit 2fd673ecf0 which tried to remove
hardreset for generic accidentally removed it for all flavors as all
others were inheriting from nv_generic_ops.  This patch reinstates
nv_hardreset() and puts it into nv_common_ops which all flavors
inherit from.  nv_generic_ops now inherits from nv_common_ops and
overrides .hardreset to ATA_OP_NULL.

While at it, explain why nv_hardreset and ATA_OP_NULL override are
necessary.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:14:34 -04:00
Shaohua Li 1253f7aabf dock: introduce .uevent for devices in dock, eg libata
dock's uevent reported itself, not ata. It might be difficult to find an
ata device just according to a dock. This patch introduces docking ops
for each device in a dock. when docking, dock driver can send device
specific uevent. This should help dock station too (not just bay)

Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-09-23 23:23:00 -04:00
Shaohua Li f730ae1838 libata: remove functions now handed by ACPI dock driver
dock driver can handle ata(bay) hotplug now. dock driver already handles
_EJ0 and _STA, so remove them. Also libata doesn't need register
notification handler anymore.

Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-09-23 23:16:41 -04:00
David S. Miller 2e57572a50 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
Conflicts:

	arch/sparc64/kernel/pci_psycho.c
2008-09-16 14:11:43 -07:00
Bob Stewart 99580664aa sata_inic162x: enable LED blinking
Enable LED blinking.

Signed-off-by: Bob Stewart <bob@evoria.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-13 16:43:20 -04:00
Stephen Hemminger da3ceb2288 ata: duplicate variable sparse warning
drivers/ata/ata_piix.c:1502:7: warning: symbol 'rc' shadows an earlier one

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-13 16:43:18 -04:00
Seth Heasley 8e48b6b307 ahci: RAID mode SATA patch for Intel Ibex Peak DeviceIDs
Add the Intel Ibex Peak (PCH) SATA RAID Controller DeviceIDs.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08 12:15:54 -04:00
David Milburn de058cdea6 pata_sil680: remove duplicate pcim_enable_device
Remove duplicate call to pcim_enable_device in sil680_init_one.

Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08 12:15:41 -04:00
Tejun Heo 9c2676b61a libata-sff: kill spurious WARN_ON() in ata_hsm_move()
On HSM_ST_ERR, ata_hsm_move() triggers WARN_ON() if AC_ERR_DEV or
AC_ERR_HSM is not set.  PHY events may trigger HSM_ST_ERR with other
error codes and, with or without it, there just isn't much reason to
do WARN_ON() on it.  Even if error code is not set there, core EH
logic won't have any problem dealing with the error condition.

OSDL bz#11065 reports this problem.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08 12:15:38 -04:00
Tejun Heo 2fd673ecf0 sata_nv: disable hardreset for generic
of them being unifying probing, hotplug and EH reset paths uniform.
Previously, broken hardreset could go unnoticed as it wasn't used
during probing but when something goes wrong or after hotplug the
problem will surface and bite hard.

OSDL bug 11195 reports that sata_nv generic flavor falls into this
category.  Hardreset itself succeeds but PHY stays offline after
hardreset.  I tried longer debounce timing but the result was the
same.

  http://bugzilla.kernel.org/show_bug.cgi?id=11195

So, it seems we'll have to drop hardreset from the generic flavor.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08 12:15:35 -04:00
Tejun Heo 17248461cb ahci: disable PMP for marvell ahcis
Marvell ahcis don't play nicely with PMPs.  Disable it.

Reported by KueiHuan Chen in the following thread.

  http://thread.gmane.org/gmane.linux.ide/33296

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: KueiHuan Chen <kueihuan.chen@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08 12:15:30 -04:00
Mark Lord 46c5784c8f sata_mv: add RocketRaid 1720 PCI ID to driver
Signed-off-by: Petr Jelen <petr.jelen@gmail.com>
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08 12:15:26 -04:00
Alan Cox 5b66c829bf ahci, pata_marvell: play nicely together
I've been chasing Jeff about this for months.  Jeff added the Marvell
device identifiers to the ahci driver without making the AHCI driver
handle the PATA port. This means a lot of users can't use current
kernels and in most distro cases can't even install.

This has been going on since March 2008 for the 6121 Marvell, and late 2007
for the 6145!!!

This was all pointed out at the time and repeatedly ignored. Bugs assigned
to Jeff about this are ignored also.

To quote Jeff in email

> "Just switch the order of 'ahci' and 'pata_marvell' in
> /etc/modprobe.conf, then use Fedora's tools regenerate the initrd.

> See?  It's not rocket science, and the current configuration can be
> easily made to work for Fedora users."

(Which isn't trivial, isn't end user, shouldn't be needed, and as it usually
breaks at install time is in fact impossible)

To quote Jeff in August 2007

> "   mv-ahci-pata
> Marvell 6121/6141 PATA support.  Needs fixing in the 'PATA controller
> command' area before it is usable, and can go upstream."

Only he add the ids anyway later and caused regressions, adding a further
id in March causing more regresions.

The actual fix for the moment is very simple. If the user has included
the pata_marvell driver let it drive the ports. If they've only selected
for SATA support give them the AHCI driver which will run the port a fraction
faster. Allow the user to control this decision via ahci.marvell_enable as
a module parameter so that distributions can ship 'it works' defaults and
smarter users (or config tools) can then flip it over it desired.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08 12:11:36 -04:00
Adrian Bunk 5110bd21b8 sparc: remove CONFIG_SUN4
While doing some easy cleanups on the sparc code I noticed that the
CONFIG_SUN4 code seems to be worse than the rest - there were some
"I don't know how it should work, but the current code definitely cannot
work." places.

And while I have seen people running Linux on machines like a
SPARCstation 5 a few years ago I don't recall having seen sun4
machines, even less ones running Linux.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-08-31 20:59:37 -07:00
Dominik Brodowski ff08705860 Merge branches 'pcmcia-config-loop' and 'pcmcia-printk' into pcmcia
* pcmcia-config-loop:
  pcmcia: pcmcia_config_loop() improvement by passing vcc
  pcmcia: pcmcia_config_loop() default CIS entry handling
  pcmcia: pcmcia_config_loop() ConfigIndex unification
  pcmcia: use pcmcia_loop_config in misc pcmcia drivers
  pcmcia: use pcmcia_loop_config in net pcmcia drivers
  pcmcia: use pcmcia_loop_config in ISDN pcmcia drivers
  pcmcia: use pcmcia_loop_config in scsi pcmcia drivers
  pcmcia: use pcmcia_loop_config in bluetooth drivers
  pcmcia: use pcmcia_loop_config in pata and ide drivers
  pcmcia: add pcmcia_loop_config() helper

* pcmcia-printk:
  pcmcia: don't add extra DEBUG cflag
  pcmcia: remove unused cs_socket_name() definition
  pcmcia: use dev_printk in module rsrc_nonstatic
  pcmcia: use dev_printk in module pcmcia
  pcmcia: use dev_printk in module pcmcia_core
  pcmcia: use dev_printk and dev_dbg in yenta_socket
2008-08-23 02:00:44 +02:00
Dominik Brodowski ad913c1192 pcmcia: pcmcia_config_loop() improvement by passing vcc
By passing the current Vcc setting to the pcmcia_config_loop callback
function, we can remove pcmcia_get_configuration_info() calls from many
drivers.

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2008-08-23 01:22:52 +02:00
Dominik Brodowski 8e2fc39dde pcmcia: pcmcia_config_loop() default CIS entry handling
Many drivers use the default CIS entry within their pcmcia_config_loop()
callback function. Therefore, factor the default CIS entry handling out.

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2008-08-23 01:22:00 +02:00
Dominik Brodowski 498ac1899b pcmcia: pcmcia_config_loop() ConfigIndex unification
Almost all drivers set p_dev->conf.ConfigIndex to cfg->index in
the pcmcia_config_loop() callback function. Therefore, factor it out.

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2008-08-23 01:21:29 +02:00
Dominik Brodowski 0bac660a77 pcmcia: use pcmcia_loop_config in pata and ide drivers
Use the config loop helper in pata_pcmcia and ide_cs

CC: Tejun Heo <htejun@gmail.com>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2008-08-23 00:49:35 +02:00
Dominik Brodowski 795659ef0e pcmcia: uniform device IDs of pata_pcmcia and ide-cs
Over time, a few differences have accumulated between pata_pcmcia
and ide-cs. Fix those.

CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2008-08-23 00:42:06 +02:00
Jeff Garzik 4ef2818534 [libata] pata_it821x: fix warning
Reported by Andrew Morton:
drivers/ata/pata_it821x.c: In function 'it821x_port_start':
drivers/ata/pata_it821x.c:609: warning: 'mtype' may be used uninitialized in
this function

Pretty horrid fix, but so's a warning..

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:33:23 -04:00
Alan Cox b15b3ebae1 libata: Fix a large collection of DMA mode mismatches
Dave Müller sent a diff for the pata_oldpiix that highlighted a problem
where a lot of the ATA drivers assume dma_mode == 0 means "no DMA" while
the core code uses 0xFF.

This turns out to have other consequences such as code doing >= XFER_UDMA_0
also catching 0xFF as UDMAlots. Fortunately it doesn't generally affect
set_dma_mode, although some drivers call back into their own set mode code
from other points.

Having been through the drivers I've added helpers for using_udma/using_mwdma
dma_enabled so that people don't open code ranges that may change (eg if UDMA8
appears somewhere)

Thanks to David for the initial bits
[and added fix for pata_oldpiix from and signed-off-by Dave Mueller
 <dave.mueller@gmx.ch>  -jg]

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:27:49 -04:00
Tejun Heo 20e2de4a50 ahci: sis controllers actually can do PMP
SIS controllers were blacklisted for PMP as enabling it made device
detection fail whether the device was PMP or not - the natural
conclusion was the controller chokes on SRST w/ pmp==15.  However, it
turned out that the controller just didn't like issuing SRST after
hardreset w/o clearing SError first.  Interestingly, the SRST itself
succeeds but the following commands fail.

If SError is cleared between hardreset and SRST, which is the default
behavior now, everything works fine and SIS controllers work with PMPs
happily.

Remove PMP blacklisting for SIS AHCIs.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Piter PUNK <piterpunk@slackware.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:19:58 -04:00
Tejun Heo ff04715bd5 pata_via: clean up recent tf_load changes
Commit bfce5e0179 implemented custom
tf_load for pata_via.  This patch cleans it up a bit.

* Instead of duplicating whole body, copy tf and set ATA_TFLAG_DEVICE
  when necessary.

* Rename via_ata_tf_load() to via_tf_load().

* No need to set .tf_load in via_port_ops_noirq as it inherits from
  via_port_ops.

* Clean up indentation.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:19:54 -04:00
Tejun Heo d127ea7b86 libata: restore SControl on detach
Save SControl during probing and restore it on detach.  This prevents
adjustments made by libata drivers to seep into the next driver which
gets attached (be it a libata one or not).

It's not clear whether SControl also needs to be restored on suspend.
The next system to have control (ACPI or kexec'd kernel) would
probably like to see the original SControl value but there's no
guarantee that a link is gonna keep working after SControl is adjusted
without a reset and adding a reset and modified recovery cycle soley
for this is an overkill.  For now, do it only for detach.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:19:46 -04:00
Tejun Heo da0e21d3fa libata: use ata_link_printk() when printing SError
SError belongs to link not port.  Use ata_link_printk() to print it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:19:44 -04:00
Tejun Heo 5dbfc9cb59 libata: always do follow-up SRST if hardreset returned -EAGAIN
As an optimization, follow-up SRST used to be skipped if
classification wasn't requested even when hardreset requested it via
-EAGAIN.  However, some hardresets can't wait for device readiness and
skipping SRST can cause timeout or other failures during revalidation.
Always perform follow-up SRST if hardreset returns -EAGAIN.  This
makes reset paths more predictable and thus less error-prone.

While at it, move hardreset error checking such that it's done right
after hardreset is finished.  This simplifies followup SRST condition
check a bit and makes the reset path easier to modify.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:19:41 -04:00
Tejun Heo a674050e06 libata: fix EH action overwriting in ata_eh_reset()
ehc->i.action got accidentally overwritten to ATA_EH_HARD/SOFTRESET in
ata_eh_reset().  The original intention was to clear reset action
which wasn't selected.  This can cause unexpected behavior when other
EH actions are scheduled together with reset.  Fix it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:19:39 -04:00
Saeed Bishara eb3a55a9f4 sata_mv: add the Gen IIE flag to the SoC devices.
The SoC sata port is based on the 7042/6042 devices (Gen IIE). This patch
will fix various issues when working with PMP and/or NCQ.

Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:19:36 -04:00
Seth Heasley c6c6a1afef ata_piix: IDE Mode SATA patch for Intel Ibex Peak DeviceIDs
This patch adds the Intel Ibex Peak (PCH) IDE mode SATA Controller DeviceIDs.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:08:04 -04:00
Seth Heasley adcb5308dd ahci: RAID mode SATA patch for Intel Ibex Peak DeviceIDs
Resend with proper whitespace.

This patch adds the Intel Ibex Peak (PCH) SATA RAID Controller DeviceIDs.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:07:56 -04:00
Tejun Heo 4bdee6c510 sata_mv: don't issue two DMA commands concurrently
sata_mv allowed issuing two DMA commands concurrently which the
hardware allows.  Unfortunately, libata core layer isn't ready for
this yet and spews ugly warning message and malfunctions on this.
Don't allow concurrent DMA commands for now.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:07:47 -04:00
Tejun Heo 05944bdf6f libata: implement no[hs]rst force params
Implement force params nohrst, nosrst and norst.  This is to work
around reset related problems and ease debugging.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:07:43 -04:00
Haavard Skinnemoen 3663b736a5 avr32: Use <mach/foo.h> instead of <asm/arch/foo.h>
Update all avr32-specific files to use the new platform-specific header
locations. Drivers shared with ARM are left alone for now.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-08-05 14:36:57 +02:00
Alan Cox 963e4975c6 pata_it821x: Driver updates and reworking
- Add support for the RDC 1010 variant
- Rework the core library to have a read_id method. This allows the hacky
  bits of it821x to go and prepares us for pata_hd
- Switch from WARN to BUG in ata_id_string as it will reboot if you get
  it wrong so WARN won't be seen
- Allow the issue of command 0xFC on the 821x. This is needed to query
  rebuild status.
- Tidy up printk formatting
- Do more ident rewriting on RAID volumes to handle firmware provided
  ident data which is rather wonky
- Report the firmware revision and device layout in RAID mode
- Don't try and disable raid on the 8211 or RDC - they don't have the
  relevant bits

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-31 02:04:50 -04:00
Tejun Heo 487eff68e4 ata_piix: subsys 106b:00a3 is apple ich8m too
Subsys 106b:00a3 also is the weird apple ich8m which chokes when the
latter two ports are accessed, add it.  Reported by Felipe Sere.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Felipe Sere <dodofxp@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-31 01:47:17 -04:00
Elias Oltmanns 49ea3b0497 libata-core: make sure that ata_force_tbl is freed in case of an error
Fix a potential memory leak when ata_init() encounters an error.

Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-31 01:47:12 -04:00
Tejun Heo 2486fa561a libata: update atapi disable handling
Global and per-LLD ATAPI disable checks were done in the command issue
path probably because it was left out during EH conversion.  On
affected machines, this can cause lots of warning messages.  Move them
to where they belong - the probing path.

Reported by Chunbo Luo.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Chunbo Luo <chunbo.luo@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-31 01:47:05 -04:00
JosephChan@via.com.tw bfce5e0179 pata_via: add VX800 flag; add function for fixing h/w bugs
Add flag VIA_SATA_PATA for vx800, VX800 uses the same
chipset(0x0581/0x5324) as CX700, which has 1 PATA channel(Master/Slave)
and 1 SATA channel(Master/Slave) Add function <via_ata_tf_load>.  This is
to fix the internal bug of VIA chipsets, which will reset the device
register after changing the IEN bit in CTL register

Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-31 01:39:31 -04:00
Ben Dooks e8389f0c44 pata_ali: misplaced pci_dev_put()
The ali_init_one() function does a search for an isa_bridge,
but then fails to release it if the revision information was
not correctly found.

the problem comes from:
	isa_bridge = pci_get_device(...);
	if (isa_bridge && ...) {
		pci_dev_put(isa_bridge);
	}

where the pci_dev_put() is never called if isa_bridge
was valid but the extra checks on the chip-revision
fail to match.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-31 01:38:19 -04:00
Dmitry Baryshkov 6cab486029 [ARM] 5179/1: Replace obsolete IRQT_* and __IRQT_* values with IRQ_TYPE_*
IRQT_* and __IRQT_* were obsoleted long ago by patch [3692/1].
Remove them completely. Sed script for the reference:

s/__IRQT_RISEDGE/IRQ_TYPE_EDGE_RISING/g
s/__IRQT_FALEDGE/IRQ_TYPE_EDGE_FALLING/g
s/__IRQT_LOWLVL/IRQ_TYPE_LEVEL_LOW/g
s/__IRQT_HIGHLVL/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_RISING/IRQ_TYPE_EDGE_RISING/g
s/IRQT_FALLING/IRQ_TYPE_EDGE_FALLING/g
s/IRQT_BOTHEDGE/IRQ_TYPE_EDGE_BOTH/g
s/IRQT_LOW/IRQ_TYPE_LEVEL_LOW/g
s/IRQT_HIGH/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_PROBE/IRQ_TYPE_PROBE/g
s/IRQT_NOEDGE/IRQ_TYPE_NONE/g

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-27 09:46:18 +01:00
Linus Torvalds 93082f0b15 Fix ahci driver 'flags' type
The new type checking of the flags arguments to irqsave and friends
(commit 3f307891ce) pointed out this thing
with a big nice warning.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-25 10:56:36 -07:00
Benjamin Herrenschmidt 84c3d4aaec Merge commit 'origin/master'
Manual merge of:

	arch/powerpc/Kconfig
	arch/powerpc/kernel/stacktrace.c
	arch/powerpc/mm/slice.c
	arch/ppc/kernel/smp.c
2008-07-16 11:07:59 +10:00
Linus Torvalds b312bf359e Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  AHCI: Remove an unnecessary flush from ahci_qc_issue
  AHCI: speed up resume
  [libata] Add support for VPD page b1
  ata: endianness annotations in pata drivers
  libata-eh: update atapi_eh_request_sense() to take @dev instead of @qc
  [libata] sata_svw: update code comments relating to data corruption
  libata/ahci: enclosure management support
  libata: improve EH internal command timeout handling
  libata: use ULONG_MAX to terminate reset timeout table
  libata: improve EH retry delay handling
  libata: consistently use msecs for time durations
2008-07-15 11:18:10 -07:00
Benjamin Herrenschmidt 43d2548bb2 Merge commit '85082fd7cbe3173198aac0eb5e85ab1edcc6352c' into test-build
Manual fixup of:

	arch/powerpc/Kconfig
2008-07-15 15:44:51 +10:00
Benjamin Herrenschmidt 5b0504c0d7 Merge commit 'gcl/gcl-next' 2008-07-15 11:55:27 +10:00
Linus Torvalds dddec01eb8 Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (37 commits)
  splice: fix generic_file_splice_read() race with page invalidation
  ramfs: enable splice write
  drivers/block/pktcdvd.c: avoid useless memset
  cdrom: revert commit 22a9189 (cdrom: use kmalloced buffers instead of buffers on stack)
  scsi: sr avoids useless buffer allocation
  block: blk_rq_map_kern uses the bounce buffers for stack buffers
  block: add blk_queue_update_dma_pad
  DAC960: push down BKL
  pktcdvd: push BKL down into driver
  paride: push ioctl down into driver
  block: use get_unaligned_* helpers
  block: extend queue_flag bitops
  block: request_module(): use format string
  Add bvec_merge_data to handle stacked devices and ->merge_bvec()
  block: integrity flags can't use bit ops on unsigned short
  cmdfilter: extend default read filter
  sg: fix odd style (extra parenthesis) introduced by cmd filter patch
  block: add bounce support to blk_rq_map_user_iov
  cfq-iosched: get rid of enable_idle being unused warning
  allow userspace to modify scsi command filter on per device basis
  ...
2008-07-14 13:15:14 -07:00
Matthew Wilcox 2640d7c0b8 AHCI: Remove an unnecessary flush from ahci_qc_issue
In an I/O heavy workload (IOZone), ahci_qc_issue is the second-highest
consumer of CPU cycles.  Removing the flush gets us approximately 10%
bandwidth improvement.  I believe this to be because the CPU can start
queueing the next request instead of waiting for the readl() to flush the
writes to the device.  The flush isn't necessary because we're using a
'queue' metaphor; we don't guarantee the command has got to the device,
nor do we need to guarantee the command has got to the controller.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:34 -04:00
Zhang Rui 24920c8a63 AHCI: speed up resume
During resume, sleep 1 second to wait for the HBA reset
to finish is a waste of time.

According to the AHCI 1.2 spec,
We should poll the HOST_CTL register,
and return error if the host reset is not
finished within 1 second.

Test results show that the HBA reset can be done quickly(in usecs).
And this patch may save nearly 1 second during resume.

Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:33 -04:00
Matthew Wilcox 1e9dbc9291 [libata] Add support for VPD page b1
SCSI VPD page b1 reports the nominal rotation speed and physical size
of the device.  Devices that conform to ATA-8 can return this information
in words 217 and 168 of the identify data.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:33 -04:00
Harvey Harrison 6ad67403da ata: endianness annotations in pata drivers
drivers/ata/pata_qdi.c:142:9: warning: incorrect type in assignment (different base types)
drivers/ata/pata_qdi.c:142:9:    expected unsigned int [unsigned] [usertype] pad
drivers/ata/pata_qdi.c:142:9:    got restricted __le32 [usertype] <noident>
drivers/ata/pata_qdi.c:146:15: warning: cast to restricted __le32

drivers/ata/pata_winbond.c:110:9: warning: incorrect type in assignment (different base types)
drivers/ata/pata_winbond.c:110:9:    expected unsigned int [unsigned] [usertype] pad
drivers/ata/pata_winbond.c:110:9:    got restricted __le32 [usertype] <noident>
drivers/ata/pata_winbond.c:114:15: warning: cast to restricted __le32

drivers/ata/pata_legacy.c:310:9: warning: incorrect type in assignment (different base types)
drivers/ata/pata_legacy.c:310:9:    expected unsigned int [unsigned] [usertype] pad
drivers/ata/pata_legacy.c:310:9:    got restricted __le32 [usertype] <noident>
drivers/ata/pata_legacy.c:314:15: warning: cast to restricted __le32
drivers/ata/pata_legacy.c:752:11: warning: cast to restricted __le32
drivers/ata/pata_legacy.c:756:9: warning: incorrect type in assignment (different base types)
drivers/ata/pata_legacy.c:756:9:    expected unsigned int [unsigned] [addressable] [assigned] [usertype] pad
drivers/ata/pata_legacy.c:756:9:    got restricted __le32 [usertype] <noident>

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:33 -04:00
Tejun Heo 3eabddb8ed libata-eh: update atapi_eh_request_sense() to take @dev instead of @qc
Update atapi_eh_request_sense() to take @dev, @sense_buf and
@dfl_sense_key instead of taking @qc and extracting information from
it.  This change is to make the function more generic and allow it to
be called from other places.

While at it, make cdb initialization use initializer.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:33 -04:00
Pavel Machek ec6add9930 [libata] sata_svw: update code comments relating to data corruption
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:33 -04:00
Kristen Carlson Accardi 18f7ba4c2f libata/ahci: enclosure management support
Add Enclosure Management support to libata and ahci.

Signed-off-by:  Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:33 -04:00
Tejun Heo 87fbc5a060 libata: improve EH internal command timeout handling
ATA_TMOUT_INTERNAL which was 30secs were used for all internal
commands which is way too long when something goes wrong.  This patch
implements command type based stepped timeouts.  Different command
types can use different timeouts and each command type can use
different timeout values after timeouts.

ie. the initial timeout is set to a value which should cover most of
the cases but not too long so that run away cases don't delay things
too much.  After the first try times out, the second try can use
longer timeout and if that one times out too, it can go for full 30sec
timeout.

IDENTIFYs use 5s - 10s - 30s timeout and all other commands use 5s -
10s timeouts.

This patch significantly cuts down the needed time to handle failure
cases while still allowing libata to work with nut job devices through
retries.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:32 -04:00
Tejun Heo d8af0eb604 libata: use ULONG_MAX to terminate reset timeout table
This doesn't introduce any functional changes.  This is to make reset
timeout table consistent with to-be-added command timeout tables.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:32 -04:00
Tejun Heo 0a2c0f5615 libata: improve EH retry delay handling
EH retries were delayed by 5 seconds to ensure that resets don't occur
back-to-back.  However, this 5 second delay is superflous or excessive
in many cases.  For example, after IDENTIFY times out, there's no
reason to wait five more seconds before retrying.

This patch adds ehc->last_reset timestamp and record the timestamp for
the last reset trial or success and uses it to space resets by
ATA_EH_RESET_COOL_DOWN which is 5 secs and removes unconditional 5 sec
sleeps.

As this change makes inter-try waits often shorter and they're
redundant in nature, this patch also removes the "retrying..."
messages.

While at it, convert explicit rounding up division to DIV_ROUND_UP().

This change speeds up EH in many cases w/o sacrificing robustness.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:32 -04:00
Tejun Heo 341c2c958e libata: consistently use msecs for time durations
libata has been using mix of jiffies and msecs for time druations.
This is getting confusing.  As writing sub HZ values in jiffies is
PITA and msecs_to_jiffies() can't be used as initializer, unify unit
for all time durations to msecs.  So, durations are in msecs and
deadlines are in jiffies.  ata_deadline() is added to compute deadline
from a start time and duration in msecs.

While at it, drop now superflous _msec suffix from arguments and
rename @timeout to @deadline if it represents a fixed point in time
rather than duration.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:32 -04:00
Stephen Rothwell e6a9192d06 powerpc/pata_mpc52xx: use linux/of_platform.h instead of asm
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-07-12 12:10:52 -06:00
Zhang Rui 3c1e389634 libata-acpi: don't call sleeping function from invalid context
The problem is introduced by commit
664d080c41.

acpi_evaluate_integer is a sleeping function,
and it should not be called with spin_lock_irqsave.
https://bugzilla.redhat.com/show_bug.cgi?id=451399

Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-11 09:42:03 -04:00
Kai Krakow edb804713f Added Targa Visionary 1000 IDE adapter to pata_sis.c
This enables short 40-wire detection for my laptop thus
enabling UDMA/100.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-11 09:38:24 -04:00
Tejun Heo b344991ace libata-acpi: filter out DIPM enable
Some BIOSen enable DIPM via _GTF which causes command timeouts under
certain configuration.  This didn't occur on 2.6.25 because 2.6.25
defaulted to SRST, so _GTF wasn't executed during boot probe, so ahci
host reset disabled DIPM and as _GTF wasn't executed after SRST, DIPM
wasn't enabled.  On 2.6.26, hardreset is used during probe and after
probe _GTF is executed enabling DIPM and thus the failures.

This patch could theoretically disable DIPM on machines which used to
have it enabled on 2.6.25 but AFAIK ahci is currently the only driver
which uses SATA ACPI hierarchy (_SDD) and as the host reset would have
always disabled DIPM, this shouldn't happen.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-11 09:38:23 -04:00
Tejun Heo d28f87aa87 ahci: give another shot at clearing all bits in irq_stat
Commit ea0c62f7cf tried to clear all
bits in irq_stat but it didn't actually achieve that as irq_stat was
anded with port_map right after read.  This patch makes ahci driver
always use the unmasked value to clear irq_status.

While at it, add explanation on the peculiarities of ahci IRQ
clearing.

This was spotted by Linus Torvalds.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-05 13:05:37 -07:00
Mark Lord c7843e8f56 sata_mv: safer logic for limit_warnings
There is a miniscule chance that two separate host controllers
might be in sata_mv at the same time and manage to decrement
the static limit_warnings variable below zero.

Fix the comparison to deal with it.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-04 09:07:12 -04:00
Tejun Heo a836d3e882 libata-sff: improve HSM violation reporting
Improve SFF HSM violation reporting such that each HSM violation can
be distinguished using ehi_desc.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-04 09:06:02 -04:00
Tejun Heo ea0c62f7cf ahci: always clear all bits in irq_stat
Some AHCI controllers (ICH7 was reported) set pending bit in
HOST_IRQ_STAT for non-existent ports and when it's not cleared falls
into IRQ storm.  Always clear full irq_stat instead of only the bits
that are handled.  As nothing changes for recognized ports, the risk
of breaking things is pretty low.

Reported and verified by Philipp Thomas in the following suse
bugzilla.

https://bugzilla.novell.com/attachment.cgi?id=215692

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Philipp Thomas <pth@novell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-04 09:05:59 -04:00
Tejun Heo 464b3286b4 sata_sil24: add DID for another adaptec flavor
There's another DID used for Adaptec card.  Add it.

Reported by Travis Read.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Travis Read <ics@dark.net.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-04 09:05:43 -04:00
FUJITA Tomonori 27f8221af4 block: add blk_queue_update_dma_pad
This adds blk_queue_update_dma_pad to prevent LLDs from overwriting
the dma pad mask wrongly (we added blk_queue_update_dma_alignment due
to the same reason).

This also converts libata to use blk_queue_update_dma_pad instead of
blk_queue_dma_pad.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-07-04 09:52:13 +02:00
Tejun Heo 70a3143af8 sata_uli: hardreset is broken
sata_uli can't do hardresets reliably and lock up.  This went
unnoticed till now as softreset was the default and hardreset was only
used after softreset failed.

Reported by Christian Casteyde in bz#10860.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-27 02:57:48 -04:00
Linus Torvalds 06d5e334a4 Merge git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  BAST: Remove old IDE driver
  pcmcia ide kingston compactflash's have a new manufacturer id
  pcmcia: add another pata/ide ID
  pcmcia: add an pata/ide ID
  ide: increase timeout in wait_drive_not_busy()
  palm_bk3710: fix resource management
2008-06-20 12:46:47 -07:00
Kristoffer Ericson a17bf22023 pcmcia: add another pata/ide ID
Addition of Transcend 1GB 45x id so that it is properly detected.

[bart: fix typo in ide-cs's ID spotted by Alan Cox]

Signed-off-by: William Peters <w1ll14@gmail.com>
Signed-off-by: Kristoffer Ericson <Kristoffer_e1@hotmail.com>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-06-20 20:53:34 +02:00
Matt Reimer 74e23386b7 pcmcia: add an pata/ide ID
Add an id for:

product info: "M-Systems", "CF300", ""
manfid: 0x000a, 0x0000
function: 4 (fixed disk)

Signed-off-by: Matt Reimer <mreimer@vpop.net>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-06-20 20:53:34 +02:00
Tejun Heo 9a3b103c27 ahci: sis can't do PMP
From: Piter PUNK <piterpunk@slackware.com>

SiS AHCIs say they can do PMP but can't and fail detection if SRST w/
pmp==15 is used.  Turn off PMP support.

tj: added patch description, adapted patch to #upstream-fixes and
    renamed board_ahci_sis to board_ahci_nopmp.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-18 20:56:58 -04:00
Tejun Heo 040dee53a7 ata_piix: add TECRA M4 to broken suspend list
TOSHIBA also used "TECRA M4" in additon to "Tecra M4", add it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-18 20:28:17 -04:00
Ben Dooks cc18e0fea7 LIBATA: Add HAVE_PATA_PLATFORM to select PATA_PLATFORM driver
Add HAVE_PATA_PLATFORM to select the pata platform driver
to ensure that we do not end up with a long 'depends on' list
when other users of this driver turn up.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-18 20:28:00 -04:00
Mark Lord c6112bd86b sata_mv: warn on PIO with multiple DRQs
Chip errata sometimes prevents reliable use of PIO commands which involve
more than a single DRQ (data request).  In normal operation, libata should
not generate such PIO commands (uses DMA instead), but they could be sent
in via SG_IO from userspace.

A full workaround might be to break up such commands into sequences
of single DRQ ones, but that's just way too complex for something
that doesn't normally happen in real life.

So, allow the attempt (it often works, despite the errata),
but log the event for reference when somebody screams.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-18 20:27:58 -04:00
Mark Lord 3bd0a70ee9 sata_mv: enable async_notify for 60x1 Rev.C0 and higher
The early chipsets cannot safely handle Async Notification (AN),
but 6041/6081 chip revision "C0" (and newer) can handle it.

So allow AN for "C0" and higher.

This enables use of hotplug on PMP ports for the 6041/6081 PCI Rev.9 chips.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-18 20:27:55 -04:00
Tejun Heo 5895ef9a5b libata: don't check whether to use DMA or not for no data commands
There's no reason to check whether to use DMA or not for no data
commands.  Don't do it.  While at it, make local variable using_pio in
atapi_xlat() set iff ATAPI_PROT_PIO is going to be used and rename
ata_check_atapi_dma() to atapi_check_dma() for consistency.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-18 20:27:49 -04:00
Tejun Heo d799e083a8 ahci: jmb361 has only one port
JMB361 has only one port but reports it has two causing longish probe
failure on the second one.  Quirk it.

Reported by Gajo Petrovic in bz 10911.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Gajo Petrovic <gajo01@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-18 20:27:45 -04:00
Shane Huang bd17243a84 ahci: Workaround HW bug for SB600/700 SATA controller PMP support
There is one bug in ATI SATA PMP of SB600 and SB700 old revision, which leads
to soft reset failure. This patch can fix the bug.

Signed-off-by: Shane Huang <shane.huang@amd.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-13 02:46:55 -04:00
Tejun Heo e297d99e10 ahci: workarounds for mcp65
MCP65 ahci can do NCQ but doesn't set the CAP bit and rev A0 and A1
can't do MSI but have MSI capability.  Implement AHCI_HFLAG_YES_NCQ
and apply appropriate workarounds.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-13 02:46:17 -04:00
Hugh Dickins 6311c90a9e libata: fix G5 SATA broken on -rc5
Fix G5 SATA irq 18: nobody cared, reported on -rc5 by Olaf Hering:
fixlet to a57c1bade5 libata-sff:
Fix oops reported in kerneloops.org for pnp devices with no ctl

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Tested-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-05 08:36:37 -07:00
Alan Cox a57c1bade5 libata-sff: Fix oops reported in kerneloops.org for pnp devices with no ctl
- Make ata_sff_altstatus private so nobody uses it by mistake
- Drop the 400nS delay from it

Add

ata_sff_irq_status	-	encapsulates the IRQ check logic

This function keeps the existing behaviour for altstatus using devices. I
actually suspect the logic was wrong before the changes but -rc isn't the
time to play with that

ata_sff_sync		-	ensure writes hit the device

Really we want an io* operation for 'is posted' eg ioisposted(ioaddr) so
that we can fix the nasty delay this causes on most systems.

- ata_sff_pause		-	400nS delay

Ensure the command hit the device and delay 400nS

- ata_sff_dma_pause

Ensure the I/O hit the device and enforce an HDMA1:0 transition delay.
Requires altstatus register exists, BUG if not so we don't risk
corruption in MWDMA modes. (UDMA the checksum will save your backside in
theory)

The only other complication then is devices with their own handlers.
rb532 can use dma_pause but scc needs to access its own altstatus
register for internal errata workarounds so directly call the drivers own
altstatus function.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-04 06:40:41 -04:00
Mark Lord ba069e376c sata_mv: PHY_MODE4 cleanups
The handling for PHY_MODE4 was originally just cloned from the
Marvell proprietary driver (with their blessing).
But we can do better than that.

Tidy things up with some judicious mask definitions, to improve maintainability.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-04 06:29:11 -04:00
Colin Ian King e1fefea9cc [libata] ata_piix: more acer short cable quirks
Add ICH6 on ACER Aspire 1694WLMi to list of laptops that use short cables
rather than 80 wire

OriginalAuthor: Tiago Sousa
OriginalLocation: http://launchpadlibrarian.net/11627664/new.ich_laptop.short.cables.diff
Bug: #187121

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-04 06:29:06 -04:00
Holger Macht 664d080c41 [libata] ACPI: Properly handle bay devices in dock stations
* Differentiate between bay devices in dock stations and others:

 - When an ACPI_NOTIFY_EJECT_REQUEST appears, just signal uevent to
   userspace (that is when the optional eject button on a bay device is
   pressed/pulled) giving the possibility to unmount file systems and to
   clean up. Also, only send uevent in case we get an EJECT_REQUEST
   without doing anything else. In other cases, you'll get an add/remove
   event because libata attaches/detaches the device.

 - In case of a dock event, which in turn signals an
   ACPI_NOTIFY_EJECT_REQUEST, immediately detach the device, because it
   may already have been gone

* In case of an ACPI_NOTIFY_DEVICE/BUS_CHECK, evaluate _STA to check if
  the device has been plugged or unplugged. If plugged, hotplug it, if
  unplugged, just signal event to userspace
  (initial patch by Matthew Garrett <mjg59@srcf.ucam.org>)

* Call ACPI _EJ0 for detached devices

Signed-off-by: Holger Macht <hmacht@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-04 06:28:50 -04:00
peerchen 3072c379bc ahci: change the Device IDs of nvidia MCP7B AHCI controller in ahci.c
Change the partial Device IDs of nvidia MCP7B AHCI controller in ahci.c,
as the actual PCI IDs deployed in the field differed from the forecasted ones
preemptively placed in the driver.

Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-30 12:40:28 -04:00
Ashish Kalra 034d8e8f27 [libata] sata_fsl: Fix broken driver, add port multiplier (PMP) support
The following commit (4c9bf4e799):
libata: replace tf_read with qc_fill_rtf for non-SFF drivers

Broke the sata_fsl.c driver in 2.6.26-rc.  I know the following patch fixes
the issue, it clearly also adds port multipler support.  The current
2.6.26-rc driver is broken.

On boot with debug enabled we get something like (w/o this patch):

spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1

.. continues for ever.

This change fixes this as a side effect of adding port multiplier support.

Signed-off-by: Ashish Kalra <ashish.kalra@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-30 12:39:44 -04:00
Tejun Heo 19ef9d5e45 libata: SRST can't be trusted on PMP sil3726
As in sil4726, SRST can't be trusted on sil3726 causing detection
problems under certain configuraitons.  I thought it was from the
Config Disk device but apparently not.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-30 12:37:56 -04:00
Randy Dunlap ec2a20e619 libata: fix libata-scsi kernel-doc notation
Fix libata-scsi kernel-doc notation:

Warning(linux-2.6.25-git15//drivers/ata/libata-scsi.c:1659): No description found for parameter 'cmd'
Warning(linux-2.6.25-git15//drivers/ata/libata-scsi.c:1971): No description found for parameter 'buf'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-30 12:37:50 -04:00
Pradeep Singh Rautela 2da676594a ata: Convert to static DEFINE_SPINLOCK(lock)
Replace deprecated static spinlock_t instance to static DEFINE_SPINLOCK(lock).

Signed-off-by: Pradeep Singh <rautelap@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-30 12:37:43 -04:00
Tejun Heo 23cf296e3b ata_piix: fix macbook ich8m problems
ICH8M on macbooks are peculiar in that some of them lock up when the
second port is enabled, some return bogus values on SIDPR access while
yet others hang on SIDPR access.  Also, the ich8m_apple_sata entry was
wrongly added below generic ich8m entry making it virtually useless.

This patch works around macbook ich8m problems by

* moving ich8m_apple_sata entry above generic ich8m entry
* dropping PIIX_FLAG_SIDPR from ich8m_apple_sata
* adding subsystem 106b:00a1 as ich8m_apple_sata

Reported and tested by MATSUBAYASHI.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: MATSUBAYASHI 'Shaolin' Kohji <shaolin@rhythmaning.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-30 12:37:29 -04:00
Mark Lord 0388a8c0d5 sata_mv: implement SoC guideline SATA_S11
The 5182 System-On-Chip (SOC) variant wants certain lower
bits to be cleared on any write to the PHY_MODE3 register.

If/when support is added for other SOC variants, we'll need
some way to uniquely identify the 5182, and not perform this
workaround for the others.

But for now, it is the only SOC variant we support here.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-30 12:37:26 -04:00
Mark Lord b406c7a665 sata_mv: workaround for 60x1 errata sata13
The "B2" variant of the 6041/6081 (genII) chips requires
that the PHY_MODE3 register be rewritten after any write
to PHY_MODE4.

This fixes a regression introduced by an earlier patch.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-30 12:37:24 -04:00
Mark Lord 5cf73bfb06 sata_mv: nuke unreleased GenIIe revisions
The only public release of the 6042/7042 chips was/is revision "B0".
Remove code that attempted to deal with earlier, non-released revs.
This matches the logic of the current Marvell "proprietary" driver.

Also, bump up the sata_mv version number, to reflect this batch of erratas.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-30 12:37:23 -04:00
Mark Lord 8c30a8b9b5 sata_mv: PHY_MODEx errata fixes
Fix and update the errata handling for the PHY_MODEx registers.
This improves receiver noise tolerance, among other things.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-30 12:37:21 -04:00
Mark Lord 1f39847255 sata_mv: move SOC_FLAG to hpriv
Convert the System-on-Chip flag from a host flag to an hpriv flag,
for better consistency with other chip-rev flags, and for easier use
in errata fixes etc.

Also change the related "HAS_PCI()" into "!IS_SOC()" for better consistency
of naming/use (everything else SOC-related already uses "SOC").

There are no functionality changes in this patch.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-30 12:37:20 -04:00
Jeff Garzik c85665ffa8 drivers/ata: trim trailing whitespace
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:56:10 -04:00
Matthew Garrett ae6c23c4e1 Fixups to ATA ACPI hotplug
The libata-acpi.c code currently accepts hotplug messages from both the
port and the device. This does not match the behaviour of the bay
driver, and may result in confusion when two hotplug requests are
received for the same device. This patch limits the hotplug notification
to removable ACPI devices, which in turn allows it to use the _STA
method to determine whether the device has been removed or inserted.
On removal, devices are marked as detached. On insertion, a hotplug scan
is started. This should avoid lockups caused by the ata layer attempting
to scan devices which have been removed. The uevent sending is moved
outside the spinlock in order to avoid a warning generated by it firing
when interrupts are disabled.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:55:18 -04:00
Tejun Heo 50af2fa1e1 libata: ignore SIMG4726 config pseudo device
I was hoping ATA_HORKAGE_NODMA | ATA_HORKAGE_SKIP_PM could keep it
happy but no even this doesn't work under certain configurations and
it's not like we can do anything useful with the cofig device anyway.
Replace ATA_HORKAGE_SKIP_PM with ATA_HORKAGE_DISABLE and use it for
the config device.  This makes the device completely ignored by
libata.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:51:48 -04:00
Tejun Heo 906c1ff44a sata_sil24: don't use NCQ if marvell 4140 PMP is attached
When 4140 PMP is attached to sil24, NCQ commands to fan out port 1 and
2 (0 based) often stall if commands are in progress to other ports.
I've tried a number of things but can't tell what's going on.  It
never happens w/ ahci and reportedly sata_mv which can issue NCQ
commands to multiple devices simultaneously like sil24 does.

Disable NCQ for devices behind 4140 PMP for the time being.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:51:48 -04:00
Tejun Heo 391191c116 libata: don't schedule LPM action seperately during probing
There's no reason to schedule LPM action after probing is complete
causing another EH iteration.  Just schedule it together with probing
itself.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:51:48 -04:00
Tejun Heo f1bbfb90e8 libata: make sure PMP notification is turned off during recovery
PMP notification during reset can make some controllers fail reset
processing and needs to be turned off during resets.  PMP attach and
full-revalidation path did this via sata_pmp_configure() but the quick
revalidation wasn't.  Move the notification disable code right above
fan-out port recovery so that it's always turned off.

This fixes obscure reset failures.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:51:48 -04:00
Tejun Heo bf1bff6fa9 libata: increase PMP register access timeout to 3s
This timeout was set low because previously PMP register access was
done via polling and register access timeouts could stack up.  This is
no longer the case.  One timeout will make all following accesses fail
immediately.

In rare cases both marvell and SIMG PMPs need almost a second.  Bump
it to 3s.

While at it, rename it to SATA_PMP_RW_TIMEOUT.  It's not specific to
SCR access.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:51:47 -04:00
Tejun Heo e0614db2a3 libata: ignore recovered PHY errors
No reason to get overzealous about recovered comm and data errors.
Some PHYs habitually sets them w/o no good reason and being draconian
about these soft error conditions doesn't seem to help anybody.

If need ever rises, we might need to add soft PHY error condition, say
AC_ERR_MAYBE_ATA_BUS and use it only to determine whether speed down
is necessary but I don't think that's very likely to happen.  It's far
more likely we'll get timeouts or fatal transmission errors if
recovered errors are so prominent that they hamper operation.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:51:47 -04:00
Tejun Heo f046519fc8 libata: kill hotplug related race condition
Originally, whole reset processing was done while the port is frozen
and SError was cleared during @postreset().  This had two race
conditions.  1: hotplug could occur after reset but before SError is
cleared and libata won't know about it.  2: hotplug could occur after
all the reset is complete but before the port is thawed.  As all
events are cleared on thaw, the hotplug event would be lost.

Commit ac371987a8 kills the first race
by clearing SError during link resume but before link onlineness test.
However, this doesn't fix race #2 and in some cases clearing SError
after SRST is a good idea.

This patch solves this problem by cross checking link onlineness with
classification result after SError is cleared and port is thawed.
Reset is retried if link is online but all devices attached to the
link are unknown.  As all devices will be revalidated, this one-way
check is enough to ensure that all devices are detected and
revalidated reliably.

This, luckily, also fixes the cases where host controller returns
bogus status while harddrive is spinning up after hotplug making
classification run before the device sends the first FIS and thus
causes misdetection.

Low level drivers can bypass the logic by setting class explicitly to
ATA_DEV_NONE if ever necessary (currently none requires this).

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:51:47 -04:00
Tejun Heo dc98c32cbe libata: move reset freeze/thaw handling into ata_eh_reset()
Previously reset freeze/thaw handling lived outside of ata_eh_reset()
mainly because the original PMP reset code needed the port frozen
while resetting all the fan-out ports, which is no longer the case.

This patch moves freeze/thaw handling into ata_eh_reset().
@prereset() and @postreset() are now called w/o freezing the port
although @prereset() an be called frozen if the port is frozen prior
to entering ata_eh_reset().

This makes code simpler and will help removing hotplug event related
races.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:51:47 -04:00
Tejun Heo 932648b007 libata: reorganize ata_eh_reset() no reset method path
Reorganize ata_eh_reset() such that @prereset() is called even when no
reset method is available and if block is used instead of goto to skip
actual reset.  This makes no reset case behave better (readiness wait)
and future changes easier.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:51:47 -04:00
Tejun Heo 0cbf0711a1 libata: fix sata_link_hardreset() @online out parameter handling
The @online out parameter is supposed to set to true iff link is
online and reset succeeded as advertised in the function description
and callers are coded expecting that.  However, sata_link_reset()
didn't behave this way on device readiness test failure.  Fix it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:51:47 -04:00
Mikael Pettersson 7715a6f9cd sata_promise: other cleanups
Minor coding-style fixes for sata_promise:
- remove stray blank lines
- fix checkpatch.pl errors; warnings about long lines
  remain, but I don't intend to address those at this time
- remove two inline directives: neither is essential and
  both functions are trivially inlinable anyway by virtue
  of being static and having a single unique call site
- fix comment in pdc_interrupt(): the bits in PDC_INT_SEQMASK
  denote SEQIDs not tags, the distinction becomes important
  when NCQ gets implemented

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:31:34 -04:00
Mikael Pettersson 821d22cdcd sata_promise: mmio access cleanups
This patch cleans up sata_promise's mmio accesses.

In sata_promise there are three distinct mmio address spaces:
1. global registers, offsets from host->iomap[PDC_MMIO_BAR]
2. per-port ATA registers, offsets from ap->ioaddr.cmd_addr
3. per-port SATA registers, offsets from ap->ioaddr.scr_addr

The driver currently often fails to indicate which address space
a given mmio base pointer refers to, which is a source of bugs
and confusion (see recent pdc_thaw() irq clearing bug; it's also
been an obstacle for the pending NCQ extensions).

To reduce these problems, adopt a coding style where the name of
a base pointer always indicates which address space it refers to:
1. global registers: host_mmio
2. per-port ATA registers: ata_mmio
3. per-port SATA registers: sata_mmio

Also rearrange register offset definitions to clearly indicate
which address space they belong to, and add a symbolic definition
for the previously hard-coded PHYMODE4 register.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:31:26 -04:00
Mikael Pettersson a13db78e22 sata_promise: fix irq clearing buglets
This patch fixes two bugs in sata_promise's irq status clearing paths:
1. When clearing the irq status for a specific port, the driver
   read the global SEQMASK register. This is wrong because that
   clears the irq status for _all_ ports.
2. pdc_thaw() incorrectly added the PDC_INT_SEQMASK host register
   offset to a per-port ata engine base address. This resulted in
   it reading the unrelated PDC_PKT_SUBMIT register, which did not
   have the desired irq status clearing effect.

In both cases the fix is to read from the port's Command/Status
register. This also matches what Promise's own driver does.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:30:47 -04:00
Harvey Harrison 07633b5d07 ata: remove FIT() macro
Use the kernel-provided clamp_val() macro.

FIT was always applied to a member of struct ata_timing (unsigned short)
and two constants.  clamp_val will not cast to short anymore.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:30:32 -04:00
Mark Lord 06aaca3f63 sata_mv: ensure empty request queue for FBS-NCQ EH
Check for an empty request queue before stopping EDMA after a FBS-NCQ error,
as per recommendation from the Marvell datasheet.

This ensures that the EDMA won't suddenly become active again
just after our subsequent check of the empty/idle bits.

Also bump DRV_VERSION.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:30:28 -04:00
Mark Lord 96e2c48793 sata_mv: cache main_irq_mask register in hpriv
Part five of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.

Keep a cached copy of the main_irq_mask so that we don't have
to stall the CPU to read it on every pass through mv_interrupt.

This significantly speeds up interrupt handling, both for sata_mv,
and for any other driver/device sharing the same PCI IRQ line.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:30:11 -04:00
Mark Lord a44253d24a sata_mv: disregard masked irqs
Part four of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.

Ignore masked IRQs in mv_interrupt().
This prevents "unexpected device interrupt while idle" messages.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:30:05 -04:00
Mark Lord 88e675e193 sata_mv: fix pmp drives not found
Part three of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.

Partially fix a reported bug whereby we sometimes miss seeing drives on
a port-multiplier, as reported by Gwendal Grignou <gwendal@google.com>.

The problem was that we were receiving unexpected interrupts
during EH from POLLed commands while accessing port-multiplier registers.
These unexpected interrupts can be prevented by masking the DONE_IRQ bit
for the port whenever not operating in EDMA mode.

Also fix port_stop() to mask all port interrupts.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:29:51 -04:00
Mark Lord c4de573b14 sata_mv: consolidate main_irq_mask updates
Part two of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.

Consolidate all updates of the host main_irq_mask register
into a single function.  This simplifies maintenance,
and also prepares the way for caching it (later).

No functionality changes in this update.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:29:10 -04:00
Mark Lord 51de32d200 sata_mv: don't blindly enable IRQs
Part one of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.

Don't blindly enable port IRQs at host init time.
Instead, enable only the bits that we want,
which in this case is simply the PCI_ERR bit.

The per-port bits can wait until the ports are reset/probed for devices.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:28:44 -04:00
Mark Lord c443c5002b sata_mv: async notify for genIIe only
Now that we handle the FIS_IRQ_CAUSE register correctly,
we can also now handle SATA asynchronous notification events.

So enable them, but only for the more modern GenIIe chips.
(older chips have unaddressed errata issues related to this).

This fixes hot plug/unplug for port-muliplier ports.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:28:17 -04:00
Mark Lord ad3aef51e1 sata_mv: group genIIe flags
Group all of the flags for GenIIe devices into a common definition,
to ensure that any updates to them are shared by all GenIIe devices.

This will help make future maintenance somewhat simpler.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:28:07 -04:00
Mark Lord e40060772d sata_mv: fis irq register fixes
Fix handling of the FIS_IRQ_CAUSE register in sata_mv.

This register exists *only* on GenIIe devices, so don't bother
writing to it on older chips.  Also, it has to be read/cleared
in mv_err_intr() before clearing the main ERR_IRQ_CAUSE register.

This keeps sata_mv from getting stuck forever on certain error types.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:27:57 -04:00
Mark Lord 9dcffd99d0 sata_mv: always do softreset
Always request a softreset after hardreset succeeds.

This fixes a regression reported by Martin Michlmayr <tbm@cyrius.com>.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:27:47 -04:00
Christophe Jaillet 68b90ee7c8 avr32/pata: avoid unnecessary memset (updated after comments)
Remove an explicit memset(.., 0, ...) to a variable allocated with
kzalloc (i.e. 'info').

Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:27:40 -04:00
Sonic Zhang b6e7b44797 pata-bf54x: Set ATAPI HSM to control IDE device terminate sequence.
Set ATAPI host state machine to control IDE device terminate sequence.
Some IDE harddisk may assert terminate sequence in the middle of a
formal DMA transaction and resume later. Bit DETECT_TERM in ATAPI_CTRL
register determines whether the ATAPI host state machine or the kernel
driver should take care of this case.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:27:29 -04:00
Alan Cox 05177f178e pata_atiixp: Don't disable
A couple of distributions (Fedora, Ubuntu) were having weird problems with the
ATI IXP series PATA controllers being reported as simplex.  At the heart of
the problem is that both distros ignored the recommendations to load pata_acpi
and ata_generic *AFTER* specific host drivers.

The underlying cause however is that if you D3 and then D0 an ATI IXP it
helpfully throws away some configuration and won't let you rewrite it.

Add checks to ata_generic and pata_acpi to pin ATIIXP devices.  Possibly the
real answer here is to quirk them and pin them, but right now we can't do that
before they've been pcim_enable()'d by a driver.

I'm indebted to David Gero for this.  His bug report not only reported the
problem but identified the cause correctly and he had tested the right values
to prove what was going on

[If you backport this for 2.6.24 you will need to pull in the 2.6.25
removal of the bogus WARN_ON() in pcim_enagle]

Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: David Gero <davidg@havidave.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:43:44 -04:00
Tejun Heo 22bfc6d5e1 sata_inic162x: update intro comment, up the version and drop EXPERIMENTAL
sata_inic162x is now ready for production use.  Bump the version,
explain what's working and what's not and drop EXPERIMENTAL.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:40:57 -04:00
Tejun Heo ba66b242b1 sata_inic162x: add cardbus support
When attached to cardbus, mmio region is at BAR 1.  Other than that,
everything else is the same.  Add support for it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:40:56 -04:00
Tejun Heo f8b0685a8e sata_inic162x: kill now unused SFF related stuff
sata_inic162x now doesn't use any SFF features.  Remove all SFF
related stuff.

* Mask unsolicited ATA interrupts.  This removes our primary source of
  spurious interrupts and spurious interrupt handling can be tightened
  up.  There's no need to clear ATA interrupts by reading status
  register either.

* Don't dance with IDMA_CTL_ATA_NIEN and simplify accesses to
  IDMA_CTL.

* Inherit from sata_port_ops instead of ata_sff_port_ops.

* Don't initialize or use ioaddr.  There's no need to map BAR0-4
  anymore.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:40:56 -04:00
Tejun Heo b3f677e501 sata_inic162x: use IDMA for ATAPI commands
Use IDMA for ATAPI commands.  Write and some misc commands time out
when executed using ATAPI_PROT_DMA but ATAPI_PROT_PIO works fine.  As
PIO is driven by DMA too, it doesn't make any noticeable difference
for native SATA devices.  inic_check_atapi_dma() is implemented to
force PIO for those ATAPI commands.

After this change, sata_inic162x issues all commands using IDMA.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:40:55 -04:00
Tejun Heo 049e8e0498 sata_inic162x: use IDMA for non DMA ATA commands
Use IDMA for PIO and non-data commands.  This allows sata_inic162x to
safely drive LBA48 devices.  Kill inic_dev_config() which contains
code to reject LBA48 devices.

With this change, status checking in inic_qc_issue() to avoid hard
lock up after hotplug can go away too.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:40:55 -04:00
Tejun Heo ab5b0235c4 sata_inic162x: kill now unused bmdma related stuff
sata_inic162x doesn't use BMDMA anymore.  Kill bmdma related stuff.

* prdctl manipulation

* port IRQ mask manipulation

* inherit ATA_BASE_SHT instead of ATA_BMDMA_SHT

* BMDMA methods

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:40:54 -04:00
Tejun Heo 3ad400a92e sata_inic162x: use IDMA for ATA_PROT_DMA
The modified driver on initio site has enough clue on how to use IDMA.
Use IDMA for ATA_PROT_DMA.

* LBA48 now works as long as it uses DMA (LBA48 devices still aren't
  allowed as it can destroy data if PIO is used for any reason).

* No need to mask IRQs for read DMAs as IDMA_DONE is properly raised
  after transfer to memory is actually completed.  There will be some
  spurious interrupts but host_intr will handle it correctly and
  manipulating port IRQ mask interacts badly with the other port for
  some reason, so command type dependent port IRQ masking is not used
  anymore.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:40:54 -04:00
Tejun Heo 364fac0e56 sata_inic162x: update TF read handling
inic162x can't reliably read back TF or at least we don't know how to
do it yet.  The only values which seem reliable are status and error.
This patch updates access to TF.

* implement inic_tf_read() which reads the TF area in mmio area

* implement custom inic_qc_fill_rtf() which only returns true if
  status indicates device error.  it'll be returning bogus addresses
  for device errors but it'll be able to report why it failed at
  least.

* implement custom inic_check_ready() and use ata_wait_after_reset()
  instead of the SFF version.

* use inic_tf_read() for classification.

This is not perfect but it fixes hotplug detection failure and at
least makes the driver report 0's instead of random garbages while
reporting valid status and error for device errors.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:40:53 -04:00
Tejun Heo b0dd9b8ef9 sata_inic162x: add / update constants
* add a bunch of constants, most are from the datasheet, a few
  undocumented ones are from initio's modified driver

* HCTL_PWRDWN is bit 12 not 13

This is in preparation of further inic162x updates.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:40:53 -04:00