Commit Graph

1661 Commits

Author SHA1 Message Date
Tejun Heo 1eedb4a90c ata_piix: add borked Tecra M4 to broken suspend list
Tecra M4 sometimes forget what it is and reports bogus data via DMI
which makes the machine evade broken suspend matching and thus fail
suspend/resume.  This patch updates piix_broken_suspend() such that it
can match such case.  As the borked DMI data is a bit generic,
matching many entries to make the match more specific is necessary.
As the usual DMI matching is limited to four entries, this patch uses
hard coded manual matching.

This is reported by Alexandru Romanescu.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-12-01 13:48:45 -05:00
Tejun Heo 6a6b97d360 libata: improve phantom device detection
Currently libata uses four methods to detect device presence.

1. PHY status if available.
2. TF register R/W test (only promotes presence, never demotes)
3. device signature after reset
4. IDENTIFY failure detection in SFF state machine

Combination of the above works well in most cases but recently there
have been a few reports where a phantom device causes unnecessary
delay during probe.  In both cases, PHY status wasn't available.  In
one case, it passed #2 and #3 and failed IDENTIFY with ATA_ERR which
didn't qualify as #4.  The other failed #2 but as it passed #3 and #4,
it still caused failure.

In both cases, phantom device reported diagnostic failure, so these
cases can be safely worked around by considering any !ATA_DRQ IDENTIFY
failure as NODEV_HINT if diagnostic failure is set.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-14 18:51:57 -05:00
Tejun Heo 19b723218b libata: fix last_reset timestamp handling
ehc->last_reset is used to ensure that resets are not issued too
close to each other.  It's initialized to jiffies minus one minute
on EH entry.  However, when new links are initialized after PMP is
probed, new links have zero for this timestamp resulting in long wait
depending on the current jiffies.

This patch makes last_set considered iff ATA_EHI_DID_RESET is set, in
which case last_reset is always initialized.  As an added precaution,
WARN_ON() is added so that warning is printed if last_reset is
in future.

This problem is spotted and debugged by Shane Huang.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Shane Huang <Shane.Huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-11 03:01:21 -05:00
Roland Dreier 44901a9684 libata: Avoid overflow in ata_tf_read_block() when tf->hba_lbal > 127
Phillip O'Donnell <phillip.odonnell@gmail.com> pointed out that the same
sign extension bug that was fixed in commit ba14a9c2 ("libata: Avoid
overflow in ata_tf_to_lba48() when tf->hba_lbal > 127") also appears to
exist in ata_tf_read_block().  Fix this by adding a cast to u64.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-11 02:59:27 -05:00
Marc Pignat a12d6c9a09 [libata] pata_pcmcia: another memory card support
Support for Apacer photo steno pro card.

Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-11 02:59:13 -05:00
Mark Salter bc170e6568 [libata] pata_sch: notice attached slave devices
I posted this last month, but was prompted to do so again in bz#467457

Add capability flag to support slave devices with pata_sch driver.

Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-11 02:58:59 -05:00
Qinghuang Feng bd6b52a17b [libata] pata_cs553*.c: cleanup kernel-doc
No arguments named @deadline in cs5535_cable_detect() and
cs5536_cable_detect().  Remove them.

Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-11 02:58:30 -05:00
Tejun Heo 8a8bc22332 libata: revert convert-to-block-tagging patches
This patch reverts the following three commits which convert libata to
use block layer tagging.

 43a49cbdf3
 e013e13bf6
 2fca5ccf97

Although using block layer tagging is the right direction, due to the
tight coupling among tag number, data structure allocation and
hardware command slot allocation, libata doesn't work correctly with
the current conversion.

The biggest problem is guaranteeing that tag 0 is always used for
non-NCQ commands.  Due to the way blk-tag is implemented and how SCSI
starts and finishes requests, such guarantee can't be made.  I'm not
sure whether this would actually break any low level driver but it
doesn't look like a good idea to break such assumption given the
frailty of ATA controllers.

So, for the time being, keep using the old dumb in-libata qc
allocation.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axobe <jens.axboe@oracle.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-10 08:04:47 -08:00
Tejun Heo 299246f9a2 libata: mask off DET when restoring SControl for detach
libata restores SControl on detach; however, trying to restore
non-zero DET can cause undeterministic behavior including PMP device
going offline till power cycling.  Mask off DET when restoring
SControl.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:33 -05:00
Tejun Heo 6a87e42e95 libata: implement ATA_HORKAGE_ATAPI_MOD16_DMA and apply it
libata always uses PIO for ATAPI commands when the number of bytes to
transfer isn't multiple of 16 but quantum DAT72 chokes on odd bytes
PIO transfers.  Implement a horkage to skip the mod16 check and apply
it to the quantum device.

This is reported by John Clark in the following thread.

  http://thread.gmane.org/gmane.linux.ide/34748

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: John Clark <clarkjc@runbox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:27 -05:00
Elias Oltmanns a464189de3 libata: Fix a potential race condition in ata_scsi_park_show()
Peter Moulder has pointed out that there is a slight chance that a
negative value might be passed to jiffies_to_msecs() in
ata_scsi_park_show(). This is fixed by saving the value of jiffies in a
local variable, thus also reducing code since the volatile variable
jiffies is accessed only once.

Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Tejun Heo <tj.kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:24 -05:00
Tejun Heo 3c324283e6 sata_nv: fix generic, nf2/3 detection regression
All three flavors of sata_nv's are different in how their hardreset
behaves.

* generic: Hardreset is not reliable.  Link often doesn't come online
  after hardreset.

* nf2/3: A little bit better - link comes online with longer debounce
  timing.  However, nf2/3 can't reliable wait for the first D2H
  Register FIS, so it can't wait for device readiness or classify the
  device after hardreset.  Follow-up SRST required.

* ck804: Hardreset finally works.

The core layer change to prefer hardreset and follow up changes
exposed the above issues and caused various detection regressions for
all three flavors.  This patch, hopefully, fixes all the known issues
and should make sata_nv error handling more reliable.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:11 -05:00
Marcin Slusarz 554d491de1 sata_via: restore vt*_prepare_host error handling
commit b9d5b89b48 (sata_via: fix support
for 5287) accidently (?) removed vt*_prepare_host error handling - restore it

catched by gcc:
drivers/ata/sata_via.c: In function 'svia_init_one':
drivers/ata/sata_via.c:567: warning: 'host' may be used uninitialized in this function

Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:06 -05:00
Mikael Pettersson cadef677e4 sata_promise: add ATA engine reset to reset ops
Promise ATA engines need to be reset when errors occur.
That's currently done for errors detected by sata_promise itself,
but it's not done for errors like timeouts detected outside of
the low-level driver.

The effect of this omission is that a timeout tends to result
in a sequence of failed COMRESETs after which libata EH gives
up and disables the port. At that point the port's ATA engine
hangs and even reloading the driver will not resume it.

To fix this, make sata_promise override ->hardreset on SATA
ports with code which calls pdc_reset_port() on the port in
question before calling libata's hardreset. PATA ports don't
use ->hardreset, so for those we override ->softreset instead.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:03 -05:00
Jens Axboe 9ce8e3073d libata: add whitelist for devices with known good pata-sata bridges
libata currently imposes a UDMA5 max transfer rate and 200 sector max
transfer size for SATA devices that sit behind a pata-sata bridge. Lots
of devices have known good bridges that don't need this limit applied.
The MTRON SSD disks are such devices. Transfer rates are increased by
20-30% with the restriction removed.

So add a "blacklist" entry for the MTRON devices, with a flag indicating
that the bridge is known good.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31 01:45:06 -04:00
Tejun Heo b9d5b89b48 sata_via: fix support for 5287
5287 used to be treated as vt6420 but it didn't work.  It's new family
of controllers called vt8251 which hosts four SATA ports as M/S of the
two ATA ports.  This configuration is rather peculiar in that although
the M/S devices are on the same port, each have its own SCR (or
equivalent link status/control) registers which screws up the
port-link-device hierarchy assumed by libata.  Another controller
which falls into this category is ata_piix w/ SIDPR access.

libata now has facility to deal with this class of controllers named
slave_link.  A low level driver for such controllers can just call
ata_slave_link_init() on the respective ports and libata will handle
all the difficult parts like following up with single SRST after
hardresetting both ports.

This patch creates new controller class vt8251, implements slave_link
aware init sequence and config space based SCR access for it and moves
5287 to the new class.

This patch is based on Joseph Chan's larger patch which was created
before slave_link was implemented in libata.

  http://thread.gmane.org/gmane.linux.kernel.commits.mm/40640

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31 01:43:28 -04:00
Roland Dreier ba14a9c291 libata: Avoid overflow in ata_tf_to_lba48() when tf->hba_lbal > 127
In ata_tf_to_lba48(), when evaluating

	(tf->hob_lbal & 0xff) << 24

the expression is promoted to signed int (since int can hold all values
of u8).  However, if hob_lbal is 128 or more, then it is treated as a
negative signed value and sign-extended when promoted to u64 to | into
sectors, which leads to the MSB 32 bits of section getting set
incorrectly.

For example, Phillip O'Donnell <phillip.odonnell@gmail.com> reported
that a 1.5GB drive caused:

    ata3.00: HPA detected: current 2930277168, native 18446744072344861488

where 2930277168 == 0xAEA87B30 and 18446744072344861488 == 0xffffffffaea87b30
which shows the problem when hob_lbal is 0xae.

Fix this by adding a cast to u64, just as is used by for hob_lbah and
hob_lbam in the function.

Reported-by: Phillip O'Donnell <phillip.odonnell@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31 01:42:59 -04:00
Randy Dunlap 5b97fbd093 ATA: remove excess kernel-doc notation
Remove excess kernel-doc function parameter notation from drivers/ata/:

Warning(drivers/ata/libata-core.c:1622): Excess function parameter or struct member 'fn' description in 'ata_pio_queue_task'
Warning(drivers/ata/libata-core.c:4655): Excess function parameter or struct member 'err_mask' description in 'ata_qc_complete'
Warning(drivers/ata/ata_piix.c:751): Excess function parameter or struct member 'udma' description in 'do_pata_set_dmamode'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31 01:42:49 -04:00
Linus Torvalds 3c136f29ba Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: ahci enclosure management bit mask
  libata: ahci enclosure management led sync
  pata_ninja32: suspend/resume support
  libata: Fix LBA48 on pata_it821x RAID volumes.
  libata: clear saved xfer_mode and ncq_enabled on device detach
  sata_sil24: configure max read request size to 4k
  libata: add missing kernel-doc
  libata: fix device iteration bugs
  ahci: Add support for Promise PDC42819
  ata: Switch all my stuff to a common address
2008-10-28 09:42:48 -07:00
David Milburn 87943acf60 libata: ahci enclosure management bit mask
Enclosure management bit mask definitions.

Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-28 00:37:15 -04:00
David Milburn eb40963c83 libata: ahci enclosure management led sync
Synchronize ahci_sw_activity and ahci_sw_activity_blink with ata_port lock.

Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-28 00:36:10 -04:00
Alan Cox e7c0d217cd pata_ninja32: suspend/resume support
I had assumed that the standard recovery would be sufficient for this
hardware but it isn't. Fix up the other registers on resume as needed. See
bug #11735

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-28 00:35:59 -04:00
Ondrej Zary 054e5f616b libata: Fix LBA48 on pata_it821x RAID volumes.
[http://lkml.org/lkml/2008/10/18/82]

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27 23:56:33 -04:00
Tejun Heo 90484ebfc9 libata: clear saved xfer_mode and ncq_enabled on device detach
libata EH saves xfer_mode and ncq_enabled at start to later set
DUBIOUS_XFER flag if it has changed.  These values need to be cleared
on device detach such that hot device swap doesn't accidentally miss
DUBIOUS_XFER.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27 23:55:40 -04:00
Tejun Heo e8b3b5e9f5 sata_sil24: configure max read request size to 4k
Due to request posting limitations, bandwidth of sil3132 is limited to
around 120MB/s with the minimum pci-e payload size (128bytes) which is
used by most consumer systems.  However, write throughput can be
slightly (~3%) increased by increasing the max read requeset size.
Configure it to 4k which is the maximum supported.  This optimization
is also done by SIMG's windows driver.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27 23:55:27 -04:00
Randy Dunlap 3cd8ddbd86 libata: add missing kernel-doc
Fix libata missing kernel-doc:

Warning(lin2628-rc2//drivers/ata/libata-core.c:4562): No description
found for parameter 'tag'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27 23:55:23 -04:00
Tejun Heo 4a9c7b3359 libata: fix device iteration bugs
There were several places where only enabled devices should be
iterated over but device enabledness wasn't checked.

* IDENTIFY data 40 wire check in cable_is_40wire()
* xfer_mode/ncq_enabled saving in ata_scsi_error()
* DUBIOUS_XFER handling in ata_set_mode()

While at it, reformat comments in cable_is_40wire().

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27 23:55:12 -04:00
Mark Nelson c77a036bec ahci: Add support for Promise PDC42819
Add an appropriate entry for the Promise PDC42819 controller. It has an
AHCI mode and so far works correctly with board_ahci.

This chip is found on Promise's FastTrak TX2650 (2 port) and TX4650 (4 port)
software-based RAID cards (for which there is a binary driver, t3sas) and
can be found on some motherboards, for example the MSI K9A2 Platinum,
which calls the chip a Promise T3 controller.

Although this controller also supports SAS devices, its default bootup mode
is AHCI and the binary driver has to do some magic to get the chip into the
appropriate mode to drive SAS disks.

Seeing as no documentation is provided by Promise, adding this entry to the
ahci driver allows the controller to be useful to people as a SATA
controller (with no ill effects on the system if a SAS disk is connected -
probing of the port just times out with "link online but device
misclassified"), without having to resort to using the binary driver. Users
who require SAS or the proprietary software raid can get this functionality
using the binary driver.

Signed-off-by: Mark Nelson <mdnelson8@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27 23:54:55 -04:00
Alan Cox ab77163008 ata: Switch all my stuff to a common address
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27 23:54:50 -04:00
Jens Axboe 43a49cbdf3 libata: fix NCQ devices behind port multipliers
For devices behind sata port multipliers, we have to make sure that
they share a tag map since all tags for that PMP must be unique.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-27 19:25:30 +01:00
Jens Axboe e013e13bf6 libata: fix bug with non-ncq devices
The recent commit 2fca5ccf97 ("libata:
switch to using block layer tagging support") to enable support for
block layer tagging in libata was broken for non-NCQ devices

The block layer initializes the tag field to -1 to detect invalid uses
of a tag, and if the libata devices does NOT support NCQ, we just used
that field to index the internal command list.  So we need to check for
-1 first and only use the tag field if it's valid.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Tested-by: Paul Mundt <lethal@linux-sh.org>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-24 08:22:38 -07:00
Jens Axboe 2fca5ccf97 libata: switch to using block layer tagging support
libata currently has a pretty dumb ATA_MAX_QUEUE loop for finding
a free tag to use. Instead of fixing that up, convert libata to
using block layer tagging - gets rid of code in libata, and is also
much faster.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-23 16:05:26 -07:00
Linus Torvalds 765426e8ee Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (123 commits)
  dock: make dock driver not a module
  ACPI: fix ia64 build warning
  ACPI: hack around sysfs warning with link order
  ACPI suspend: fix build warning when CONFIG_ACPI_SLEEP=n
  intel_menlo: fix build warning
  panasonic-laptop: fix build
  ACPICA: Update version to 20080926
  ACPICA: Add support for zero-length buffer-to-string conversions
  ACPICA: New: Validation for predefined ACPI methods/objects
  ACPICA: Fix for implicit return compatibility
  ACPICA: Fixed a couple memory leaks associated with "implicit return"
  ACPICA: Optimize buffer allocation procedure
  ACPICA: Fix possible memory leak, error exit path
  ACPICA: Fix fault after mem allocation failure in AML parser
  ACPICA: Remove unused ACPI register bit definition
  ACPICA: Update version to 20080829
  ACPICA: Fix possible memory leak in acpi_ns_get_external_pathname
  ACPICA: Cleanup for internal Reference Object
  ACPICA: Update comments - no functional changes
  ACPICA: Update for Reference ACPI_OPERAND_OBJECT
  ...
2008-10-23 10:20:36 -07:00
Len Brown 057316cc6a Merge branch 'linus' into test
Conflicts:
	MAINTAINERS
	arch/x86/kernel/acpi/boot.c
	arch/x86/kernel/acpi/sleep.c
	drivers/acpi/Kconfig
	drivers/pnp/Makefile
	drivers/pnp/quirks.c

Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-23 00:11:07 -04:00
Len Brown 47bf31adc5 Merge branch 'dock' into test
Conflicts:
	drivers/acpi/osl.c

Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-22 23:25:26 -04:00
Tejun Heo b78152e9db sata_via: load DEVICE register when CTL changes
VIA controllers clear DEVICE register when IEN changes.  Make sure
DEVICE is updated along with CTL.

This change is separated from Joseph Chan's larger patch.

  http://thread.gmane.org/gmane.linux.kernel.commits.mm/40640

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-22 20:42:47 -04:00
Tejun Heo 816ab89782 libata: set device class to NONE if phys_offline
Reset methods don't have access to phys link status for slave links
and may incorrectly indicate device presence causing unnecessary probe
failures for unoccupied links.  This patch clears device class to NONE
during post-reset processing if phys link is offline.

As on/offlineness semantics is strictly defined and used in multiple
places by the core layer, this won't change behavior for drivers which
don't use slave links.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-22 20:42:43 -04:00
Tejun Heo a568d1d2e2 libata-eh: fix slave link EH action mask handling
Slave link action mask is transferred to master link and all the EH
actions are taken by the master link.  ata_eh_about_to_do() and
ata_eh_done() are called with ATA_EH_ALL_ACTIONS to clear the slave
link actions during transfer.  This always sets ATA_PFLAG_RECOVERED
flag causing spurious "EH complete" messages.

Don't set ATA_PFLAG_RECOVERED for slave link actions.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-22 20:40:21 -04:00
Tejun Heo 848e4c68c4 libata: transfer EHI control flags to slave ehc.i
ATA_EHI_NO_AUTOPSY and ATA_EHI_QUIET are used to control the behavior
of EH.  As only the master link is visible outside EH, these flags are
set only for the master link although they should also apply to the
slave link, which causes spurious EH messages during probe and
suspend/resume.

This patch transfers those two flags to slave ehc.i before performing
slave autopsy and reporting.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-22 20:40:19 -04:00
Tejun Heo 570106df6b libata-sff: fix ata_sff_post_internal_cmd()
ata_sff_post_internal_cmd() needs to grab port lock before calling
ata_bmdma_stop() and also need to clear hsm_task_state.  Fix it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-22 20:40:15 -04:00
Tejun Heo f667fdbbbe libata: initialize port_task when !CONFIG_ATA_SFF
ap->port_task was not initialized if !CONFIG_ATA_SFF later triggering
lockdep warning.  Make sure it's initialized.

Reported by Larry Finger.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-22 20:40:01 -04:00
Benjamin Herrenschmidt 6dc6472581 Merge commit 'origin'
Manual fixup of conflicts on:

	arch/powerpc/include/asm/dcr-regs.h
	drivers/net/ibm_newemac/core.h
2008-10-15 11:31:54 +11:00
Linus Torvalds 2be4ff2f08 Merge git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: (49 commits)
  pcmcia: ioctl-internal definitions
  pcmcia: cistpl header cleanup
  pcmcia: remove unused argument to pcmcia_parse_tuple()
  pcmcia: card services header cleanup
  pcmcia: device_id header cleanup
  pcmcia: encapsulate ioaddr_t
  pcmcia: cleanup device driver header file
  pcmcia: cleanup socket services header file
  pcmcia: merge ds_internal.h into cs_internal.h
  pcmcia: cleanup cs_internal.h
  pcmcia: cs_internal.h is internal
  pcmcia: use dev_printk for cs_error()
  pcmcia: remove CS_ error codes alltogether
  pcmcia: deprecate CS_BAD_TUPLE
  pcmcia: deprecate CS_BAD_ARGS
  pcmcia: deprecate CS_BAD_BASE, CS_BAD_IRQ, CS_BAD_OFFSET and CS_BAD_SIZE
  pcmcia: deprecate CS_BAD_ATTRIBUTE, CS_BAD_TYPE and CS_BAD_PAGE
  pcmcia: deprecate CS_NO_MORE_ITEMS
  pcmcia: deprecate CS_IN_USE
  pcmcia: deprecate CS_CONFIGURATION_LOCKED
  ...

Fix trivial conflict in drivers/pcmcia/ds.c manually
2008-10-13 14:12:40 -07:00
Linus Torvalds 0710483959 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6: (180 commits)
  leo: disable cursor when leaving graphics mode
  cg6: disable cursor when leaving graphics mode
  sparc32: sun4m interrupt mask cleanup
  drivers/rtc/Kconfig: don't build rtc-cmos.o on sparc32
  sparc: arch/sparc/kernel/pmc.c -- extra #include?
  sparc32: Add more extensive documentation of sun4m interrupts.
  sparc32: Kill irq_rcvreg from sun4m_irq.c
  sparc32: Delete master_l10_limit.
  sparc32: Use PROM device probing for sun4c timers.
  sparc32: Use PROM device probing for sun4c interrupt register.
  sparc32: Delete claim_ticker14().
  sparc32: Stop calling claim_ticker14() from sun4c_irq.c
  sparc32: Kill clear_profile_irq btfixup entry.
  sparc32: Call sun4m_clear_profile_irq() directly from sun4m_smp.c
  sparc32: Remove #if 0'd code from sun4c_irq.c
  sparc32: Remove some SMP ifdefs in sun4d_irq.c
  sparc32: Use PROM infrastructure for probing and mapping sun4d timers.
  sparc32: Use PROM device probing for sun4m irq registers.
  sparc32: Use PROM device probing for sun4m timer registers.
  sparc: Fix user_regset 'n' field values.
  ...
2008-10-12 11:40:55 -07:00
David S. Miller 56c5d900db Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:

	sound/core/memalloc.c
2008-10-11 12:39:35 -07:00
Bartlomiej Zolnierkiewicz a4f19040a3 libata: WIN_* -> ATA_CMD_*
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-10-10 22:39:20 +02:00
Linus Torvalds e26feff647 Merge branch 'for-2.6.28' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.28' of git://git.kernel.dk/linux-2.6-block: (132 commits)
  doc/cdrom: Trvial documentation error, file not present
  block_dev: fix kernel-doc in new functions
  block: add some comments around the bio read-write flags
  block: mark bio_split_pool static
  block: Find bio sector offset given idx and offset
  block: gendisk integrity wrapper
  block: Switch blk_integrity_compare from bdev to gendisk
  block: Fix double put in blk_integrity_unregister
  block: Introduce integrity data ownership flag
  block: revert part of d7533ad0e132f92e75c1b2eb7c26387b25a583c1
  bio.h: Remove unused conditional code
  block: remove end_{queued|dequeued}_request()
  block: change elevator to use __blk_end_request()
  gdrom: change to use __blk_end_request()
  memstick: change to use __blk_end_request()
  virtio_blk: change to use __blk_end_request()
  blktrace: use BLKTRACE_BDEV_SIZE as the name size for setup structure
  block: add lld busy state exporting interface
  block: Fix blk_start_queueing() to not kick a stopped queue
  include blktrace_api.h in headers_install
  ...
2008-10-10 10:52:45 -07:00
Linus Torvalds 82219fceeb Merge branch 'upstream-2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  ata_piix: IDE Mode SATA patch for Intel Ibex Peak DeviceIDs
  libata-eh: clear UNIT ATTENTION after reset
  ata_piix: add Hercules EC-900 mini-notebook to ich_laptop short cable list
  libata: reorder ata_device to remove 8 bytes of padding on 64 bits
  [libata] pata_bf54x: Add proper PM operation
  pata_sil680: convert CONFIG_PPC_MERGE to CONFIG_PPC
  libata: Implement disk shock protection support
  [libata] Introduce ata_id_has_unload()
  PATA: RPC now selects HAVE_PATA_PLATFORM for pata platform driver
  ata_piix: drop merged SCR access and use slave_link instead
  libata: implement slave_link
  libata: misc updates to prepare for slave link
  libata: reimplement link iterator
  libata: make SCR access ops per-link
2008-10-10 07:46:45 -07:00
Anton Vorontsov 4538d0ca71 powerpc: Fix no interrupt handling in pata_of_platform
When no interrupt is specified the pata_of_platform fills the irq_res
resource with -1, which is wrong to do for two reasons:

1. By definition, 'no irq' should be IRQ 0, not some negative integer;
2. pata_platform checks for irq_res.start > 0, but since irq_res.start
   is unsigned type, the check will be true for `-1'.

Reported-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2008-10-10 15:55:17 +11:00
Jens Axboe 8bff7c6b0f libata: set queue SSD flag for SSD devices
SSD devices should give an RPM setting of 1 in word 217 of the ID
page. If we see such a device, tell the block layer about it.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:19 +02:00
Jens Axboe 242f9dcb8b block: unify request timeout handling
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.

Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.

Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:13 +02:00
Seth Heasley 0395e61bab ata_piix: IDE Mode SATA patch for Intel Ibex Peak DeviceIDs
This patch updates the Intel Ibex Peak (PCH) IDE mode SATA Controller DeviceIDs.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:29:12 -04:00
Tejun Heo 11fc33da8d libata-eh: clear UNIT ATTENTION after reset
Resets make ATAPI devices raise UNIT ATTENTION which fails the next
command.  As resets can happen asynchronously for unrelated reasons,
this sometimes disrupts innocent users.  For example, reading DVD
fails after the system wakes up from suspend or the other device
sharing the channel went through bus error.

Clearing UA has some problems as it might clear UA which the userland
needs to know about.  However, UA after resets can only be about the
reset itself and benefits of clearing it overweights cons.  Missing UA
can only delay failure to one of the following commands anyway.  For
example, timeout while burning is in progress will trigger reset and
reset the device state and probably corrupt the burning run.  Although
the userland application won't get the UA, its pending writes will
fail.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:29:06 -04:00
Herton Ronaldo Krzesinski d09addf65c ata_piix: add Hercules EC-900 mini-notebook to ich_laptop short cable list
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:28:40 -04:00
Sonic Zhang 67e3e221d6 [libata] pata_bf54x: Add proper PM operation
[akpm@linux-foundation.org: remove ifdefs, make things static]
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:28:29 -04:00
Kumar Gala 47d692a946 pata_sil680: convert CONFIG_PPC_MERGE to CONFIG_PPC
Now that arch/ppc is dead CONFIG_PPC_MERGE is always defined for all
powerpc platforms and we want to get rid of CONFIG_PPC_MERGE use
CONFIG_PPC instead.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:28:02 -04:00
Elias Oltmanns 45fabbb77b libata: Implement disk shock protection support
On user request (through sysfs), the IDLE IMMEDIATE command with UNLOAD
FEATURE as specified in ATA-7 is issued to the device and processing of
the request queue is stopped thereafter until the specified timeout
expires or user space asks to resume normal operation. This is supposed
to prevent the heads of a hard drive from accidentally crashing onto the
platter when a heavy shock is anticipated (like a falling laptop
expected to hit the floor). In fact, the whole port stops processing
commands until the timeout has expired in order to avoid any resets due
to failed commands on another device.

Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:27:54 -04:00
Ben Dooks 2ad69677b6 PATA: RPC now selects HAVE_PATA_PLATFORM for pata platform driver
The RPC machine type now selects HAVE_PATA_PLATFORM so we can remove
the special case in the PATA_PLATFORM configuration code.

Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:25:43 -04:00
Tejun Heo be77e43abb ata_piix: drop merged SCR access and use slave_link instead
Now that libata has slave_link, there's no need to keep ugly merged
SCR access.  Drop it and use slave_link instead.  This results in
simpler code and much better separate link handling for master and
slave.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:25:32 -04:00
Tejun Heo b1c72916ab libata: implement slave_link
Explanation taken from the comment of ata_slave_link_init().

 In libata, a port contains links and a link contains devices.  There
 is single host link but if a PMP is attached to it, there can be
 multiple fan-out links.  On SATA, there's usually a single device
 connected to a link but PATA and SATA controllers emulating TF based
 interface can have two - master and slave.

 However, there are a few controllers which don't fit into this
 abstraction too well - SATA controllers which emulate TF interface
 with both master and slave devices but also have separate SCR
 register sets for each device.  These controllers need separate links
 for physical link handling (e.g. onlineness, link speed) but should
 be treated like a traditional M/S controller for everything else
 (e.g. command issue, softreset).

 slave_link is libata's way of handling this class of controllers
 without impacting core layer too much.  For anything other than
 physical link handling, the default host link is used for both master
 and slave.  For physical link handling, separate @ap->slave_link is
 used.  All dirty details are implemented inside libata core layer.
 From LLD's POV, the only difference is that prereset, hardreset and
 postreset are called once more for the slave link, so the reset
 sequence looks like the following.

 prereset(M) -> prereset(S) -> hardreset(M) -> hardreset(S) ->
 softreset(M) -> postreset(M) -> postreset(S)

 Note that softreset is called only for the master.  Softreset resets
 both M/S by definition, so SRST on master should handle both (the
 standard method will work just fine).

As slave_link excludes PMP support and only code paths which deal with
the attributes of physical link are affected, all the changes are
localized to libata.h, libata-core.c and libata-eh.c.

 * ata_is_host_link() updated so that slave_link is considered as host
   link too.

 * iterator extended to iterate over the slave_link when using the
   underbarred version.

 * force param handling updated such that devno 16 is mapped to the
   slave link/device.

 * ata_link_on/offline() updated to return the combined result from
   master and slave link.  ata_phys_link_on/offline() are the direct
   versions.

 * EH autopsy and report are performed separately for master slave
   links.  Reset is udpated to implement the above described reset
   sequence.

Except for reset update, most changes are minor, many of them just
modifying dev->link to ata_dev_phys_link(dev) or using phys online
test instead.

After this update, LLDs can take full advantage of per-dev SCR
registers by simply turning on slave link.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:25:28 -04:00
Tejun Heo b5b3fa386b libata: misc updates to prepare for slave link
* Add ATA_EH_ALL_ACTIONS.

* Make sata_link_{on|off}_line() return bool instead of int.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:22:32 -04:00
Tejun Heo aadffb682c libata: reimplement link iterator
Implement __ata_port_next_link() and reimplement
__ata_port_for_each_link() and ata_port_for_each_link() using it.
This removes relatively large inlined code and makes iteration easier
to extend.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:22:30 -04:00
Tejun Heo 82ef04fb4c libata: make SCR access ops per-link
Logically, SCR access ops should take @link; however, there was no
compelling reason to convert all SCR access ops when adding @link
abstraction as there's one-to-one mapping between a port and a non-PMP
link.  However, that assumption won't hold anymore with the scheduled
addition of slave link.

Make SCR access ops per-link.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:22:28 -04:00
Tejun Heo 4c1eb90a09 sata_nv: reinstate nv_hardreset() for non generic controllers
Commit 2fd673ecf0 which tried to remove
hardreset for generic accidentally removed it for all flavors as all
others were inheriting from nv_generic_ops.  This patch reinstates
nv_hardreset() and puts it into nv_common_ops which all flavors
inherit from.  nv_generic_ops now inherits from nv_common_ops and
overrides .hardreset to ATA_OP_NULL.

While at it, explain why nv_hardreset and ATA_OP_NULL override are
necessary.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:14:34 -04:00
Shaohua Li 1253f7aabf dock: introduce .uevent for devices in dock, eg libata
dock's uevent reported itself, not ata. It might be difficult to find an
ata device just according to a dock. This patch introduces docking ops
for each device in a dock. when docking, dock driver can send device
specific uevent. This should help dock station too (not just bay)

Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-09-23 23:23:00 -04:00
Shaohua Li f730ae1838 libata: remove functions now handed by ACPI dock driver
dock driver can handle ata(bay) hotplug now. dock driver already handles
_EJ0 and _STA, so remove them. Also libata doesn't need register
notification handler anymore.

Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-09-23 23:16:41 -04:00
David S. Miller 2e57572a50 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
Conflicts:

	arch/sparc64/kernel/pci_psycho.c
2008-09-16 14:11:43 -07:00
Bob Stewart 99580664aa sata_inic162x: enable LED blinking
Enable LED blinking.

Signed-off-by: Bob Stewart <bob@evoria.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-13 16:43:20 -04:00
Stephen Hemminger da3ceb2288 ata: duplicate variable sparse warning
drivers/ata/ata_piix.c:1502:7: warning: symbol 'rc' shadows an earlier one

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-13 16:43:18 -04:00
Seth Heasley 8e48b6b307 ahci: RAID mode SATA patch for Intel Ibex Peak DeviceIDs
Add the Intel Ibex Peak (PCH) SATA RAID Controller DeviceIDs.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08 12:15:54 -04:00
David Milburn de058cdea6 pata_sil680: remove duplicate pcim_enable_device
Remove duplicate call to pcim_enable_device in sil680_init_one.

Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08 12:15:41 -04:00
Tejun Heo 9c2676b61a libata-sff: kill spurious WARN_ON() in ata_hsm_move()
On HSM_ST_ERR, ata_hsm_move() triggers WARN_ON() if AC_ERR_DEV or
AC_ERR_HSM is not set.  PHY events may trigger HSM_ST_ERR with other
error codes and, with or without it, there just isn't much reason to
do WARN_ON() on it.  Even if error code is not set there, core EH
logic won't have any problem dealing with the error condition.

OSDL bz#11065 reports this problem.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08 12:15:38 -04:00
Tejun Heo 2fd673ecf0 sata_nv: disable hardreset for generic
of them being unifying probing, hotplug and EH reset paths uniform.
Previously, broken hardreset could go unnoticed as it wasn't used
during probing but when something goes wrong or after hotplug the
problem will surface and bite hard.

OSDL bug 11195 reports that sata_nv generic flavor falls into this
category.  Hardreset itself succeeds but PHY stays offline after
hardreset.  I tried longer debounce timing but the result was the
same.

  http://bugzilla.kernel.org/show_bug.cgi?id=11195

So, it seems we'll have to drop hardreset from the generic flavor.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08 12:15:35 -04:00
Tejun Heo 17248461cb ahci: disable PMP for marvell ahcis
Marvell ahcis don't play nicely with PMPs.  Disable it.

Reported by KueiHuan Chen in the following thread.

  http://thread.gmane.org/gmane.linux.ide/33296

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: KueiHuan Chen <kueihuan.chen@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08 12:15:30 -04:00
Mark Lord 46c5784c8f sata_mv: add RocketRaid 1720 PCI ID to driver
Signed-off-by: Petr Jelen <petr.jelen@gmail.com>
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08 12:15:26 -04:00
Alan Cox 5b66c829bf ahci, pata_marvell: play nicely together
I've been chasing Jeff about this for months.  Jeff added the Marvell
device identifiers to the ahci driver without making the AHCI driver
handle the PATA port. This means a lot of users can't use current
kernels and in most distro cases can't even install.

This has been going on since March 2008 for the 6121 Marvell, and late 2007
for the 6145!!!

This was all pointed out at the time and repeatedly ignored. Bugs assigned
to Jeff about this are ignored also.

To quote Jeff in email

> "Just switch the order of 'ahci' and 'pata_marvell' in
> /etc/modprobe.conf, then use Fedora's tools regenerate the initrd.

> See?  It's not rocket science, and the current configuration can be
> easily made to work for Fedora users."

(Which isn't trivial, isn't end user, shouldn't be needed, and as it usually
breaks at install time is in fact impossible)

To quote Jeff in August 2007

> "   mv-ahci-pata
> Marvell 6121/6141 PATA support.  Needs fixing in the 'PATA controller
> command' area before it is usable, and can go upstream."

Only he add the ids anyway later and caused regressions, adding a further
id in March causing more regresions.

The actual fix for the moment is very simple. If the user has included
the pata_marvell driver let it drive the ports. If they've only selected
for SATA support give them the AHCI driver which will run the port a fraction
faster. Allow the user to control this decision via ahci.marvell_enable as
a module parameter so that distributions can ship 'it works' defaults and
smarter users (or config tools) can then flip it over it desired.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08 12:11:36 -04:00
Adrian Bunk 5110bd21b8 sparc: remove CONFIG_SUN4
While doing some easy cleanups on the sparc code I noticed that the
CONFIG_SUN4 code seems to be worse than the rest - there were some
"I don't know how it should work, but the current code definitely cannot
work." places.

And while I have seen people running Linux on machines like a
SPARCstation 5 a few years ago I don't recall having seen sun4
machines, even less ones running Linux.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-08-31 20:59:37 -07:00
Dominik Brodowski ff08705860 Merge branches 'pcmcia-config-loop' and 'pcmcia-printk' into pcmcia
* pcmcia-config-loop:
  pcmcia: pcmcia_config_loop() improvement by passing vcc
  pcmcia: pcmcia_config_loop() default CIS entry handling
  pcmcia: pcmcia_config_loop() ConfigIndex unification
  pcmcia: use pcmcia_loop_config in misc pcmcia drivers
  pcmcia: use pcmcia_loop_config in net pcmcia drivers
  pcmcia: use pcmcia_loop_config in ISDN pcmcia drivers
  pcmcia: use pcmcia_loop_config in scsi pcmcia drivers
  pcmcia: use pcmcia_loop_config in bluetooth drivers
  pcmcia: use pcmcia_loop_config in pata and ide drivers
  pcmcia: add pcmcia_loop_config() helper

* pcmcia-printk:
  pcmcia: don't add extra DEBUG cflag
  pcmcia: remove unused cs_socket_name() definition
  pcmcia: use dev_printk in module rsrc_nonstatic
  pcmcia: use dev_printk in module pcmcia
  pcmcia: use dev_printk in module pcmcia_core
  pcmcia: use dev_printk and dev_dbg in yenta_socket
2008-08-23 02:00:44 +02:00
Dominik Brodowski ad913c1192 pcmcia: pcmcia_config_loop() improvement by passing vcc
By passing the current Vcc setting to the pcmcia_config_loop callback
function, we can remove pcmcia_get_configuration_info() calls from many
drivers.

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2008-08-23 01:22:52 +02:00
Dominik Brodowski 8e2fc39dde pcmcia: pcmcia_config_loop() default CIS entry handling
Many drivers use the default CIS entry within their pcmcia_config_loop()
callback function. Therefore, factor the default CIS entry handling out.

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2008-08-23 01:22:00 +02:00
Dominik Brodowski 498ac1899b pcmcia: pcmcia_config_loop() ConfigIndex unification
Almost all drivers set p_dev->conf.ConfigIndex to cfg->index in
the pcmcia_config_loop() callback function. Therefore, factor it out.

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2008-08-23 01:21:29 +02:00
Dominik Brodowski 0bac660a77 pcmcia: use pcmcia_loop_config in pata and ide drivers
Use the config loop helper in pata_pcmcia and ide_cs

CC: Tejun Heo <htejun@gmail.com>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2008-08-23 00:49:35 +02:00
Dominik Brodowski 795659ef0e pcmcia: uniform device IDs of pata_pcmcia and ide-cs
Over time, a few differences have accumulated between pata_pcmcia
and ide-cs. Fix those.

CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2008-08-23 00:42:06 +02:00
Jeff Garzik 4ef2818534 [libata] pata_it821x: fix warning
Reported by Andrew Morton:
drivers/ata/pata_it821x.c: In function 'it821x_port_start':
drivers/ata/pata_it821x.c:609: warning: 'mtype' may be used uninitialized in
this function

Pretty horrid fix, but so's a warning..

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:33:23 -04:00
Alan Cox b15b3ebae1 libata: Fix a large collection of DMA mode mismatches
Dave Müller sent a diff for the pata_oldpiix that highlighted a problem
where a lot of the ATA drivers assume dma_mode == 0 means "no DMA" while
the core code uses 0xFF.

This turns out to have other consequences such as code doing >= XFER_UDMA_0
also catching 0xFF as UDMAlots. Fortunately it doesn't generally affect
set_dma_mode, although some drivers call back into their own set mode code
from other points.

Having been through the drivers I've added helpers for using_udma/using_mwdma
dma_enabled so that people don't open code ranges that may change (eg if UDMA8
appears somewhere)

Thanks to David for the initial bits
[and added fix for pata_oldpiix from and signed-off-by Dave Mueller
 <dave.mueller@gmx.ch>  -jg]

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:27:49 -04:00
Tejun Heo 20e2de4a50 ahci: sis controllers actually can do PMP
SIS controllers were blacklisted for PMP as enabling it made device
detection fail whether the device was PMP or not - the natural
conclusion was the controller chokes on SRST w/ pmp==15.  However, it
turned out that the controller just didn't like issuing SRST after
hardreset w/o clearing SError first.  Interestingly, the SRST itself
succeeds but the following commands fail.

If SError is cleared between hardreset and SRST, which is the default
behavior now, everything works fine and SIS controllers work with PMPs
happily.

Remove PMP blacklisting for SIS AHCIs.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Piter PUNK <piterpunk@slackware.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:19:58 -04:00
Tejun Heo ff04715bd5 pata_via: clean up recent tf_load changes
Commit bfce5e0179 implemented custom
tf_load for pata_via.  This patch cleans it up a bit.

* Instead of duplicating whole body, copy tf and set ATA_TFLAG_DEVICE
  when necessary.

* Rename via_ata_tf_load() to via_tf_load().

* No need to set .tf_load in via_port_ops_noirq as it inherits from
  via_port_ops.

* Clean up indentation.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:19:54 -04:00
Tejun Heo d127ea7b86 libata: restore SControl on detach
Save SControl during probing and restore it on detach.  This prevents
adjustments made by libata drivers to seep into the next driver which
gets attached (be it a libata one or not).

It's not clear whether SControl also needs to be restored on suspend.
The next system to have control (ACPI or kexec'd kernel) would
probably like to see the original SControl value but there's no
guarantee that a link is gonna keep working after SControl is adjusted
without a reset and adding a reset and modified recovery cycle soley
for this is an overkill.  For now, do it only for detach.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:19:46 -04:00
Tejun Heo da0e21d3fa libata: use ata_link_printk() when printing SError
SError belongs to link not port.  Use ata_link_printk() to print it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:19:44 -04:00
Tejun Heo 5dbfc9cb59 libata: always do follow-up SRST if hardreset returned -EAGAIN
As an optimization, follow-up SRST used to be skipped if
classification wasn't requested even when hardreset requested it via
-EAGAIN.  However, some hardresets can't wait for device readiness and
skipping SRST can cause timeout or other failures during revalidation.
Always perform follow-up SRST if hardreset returns -EAGAIN.  This
makes reset paths more predictable and thus less error-prone.

While at it, move hardreset error checking such that it's done right
after hardreset is finished.  This simplifies followup SRST condition
check a bit and makes the reset path easier to modify.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:19:41 -04:00
Tejun Heo a674050e06 libata: fix EH action overwriting in ata_eh_reset()
ehc->i.action got accidentally overwritten to ATA_EH_HARD/SOFTRESET in
ata_eh_reset().  The original intention was to clear reset action
which wasn't selected.  This can cause unexpected behavior when other
EH actions are scheduled together with reset.  Fix it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:19:39 -04:00
Saeed Bishara eb3a55a9f4 sata_mv: add the Gen IIE flag to the SoC devices.
The SoC sata port is based on the 7042/6042 devices (Gen IIE). This patch
will fix various issues when working with PMP and/or NCQ.

Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:19:36 -04:00
Seth Heasley c6c6a1afef ata_piix: IDE Mode SATA patch for Intel Ibex Peak DeviceIDs
This patch adds the Intel Ibex Peak (PCH) IDE mode SATA Controller DeviceIDs.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:08:04 -04:00
Seth Heasley adcb5308dd ahci: RAID mode SATA patch for Intel Ibex Peak DeviceIDs
Resend with proper whitespace.

This patch adds the Intel Ibex Peak (PCH) SATA RAID Controller DeviceIDs.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:07:56 -04:00
Tejun Heo 4bdee6c510 sata_mv: don't issue two DMA commands concurrently
sata_mv allowed issuing two DMA commands concurrently which the
hardware allows.  Unfortunately, libata core layer isn't ready for
this yet and spews ugly warning message and malfunctions on this.
Don't allow concurrent DMA commands for now.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:07:47 -04:00
Tejun Heo 05944bdf6f libata: implement no[hs]rst force params
Implement force params nohrst, nosrst and norst.  This is to work
around reset related problems and ease debugging.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22 02:07:43 -04:00
Haavard Skinnemoen 3663b736a5 avr32: Use <mach/foo.h> instead of <asm/arch/foo.h>
Update all avr32-specific files to use the new platform-specific header
locations. Drivers shared with ARM are left alone for now.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-08-05 14:36:57 +02:00
Alan Cox 963e4975c6 pata_it821x: Driver updates and reworking
- Add support for the RDC 1010 variant
- Rework the core library to have a read_id method. This allows the hacky
  bits of it821x to go and prepares us for pata_hd
- Switch from WARN to BUG in ata_id_string as it will reboot if you get
  it wrong so WARN won't be seen
- Allow the issue of command 0xFC on the 821x. This is needed to query
  rebuild status.
- Tidy up printk formatting
- Do more ident rewriting on RAID volumes to handle firmware provided
  ident data which is rather wonky
- Report the firmware revision and device layout in RAID mode
- Don't try and disable raid on the 8211 or RDC - they don't have the
  relevant bits

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-31 02:04:50 -04:00
Tejun Heo 487eff68e4 ata_piix: subsys 106b:00a3 is apple ich8m too
Subsys 106b:00a3 also is the weird apple ich8m which chokes when the
latter two ports are accessed, add it.  Reported by Felipe Sere.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Felipe Sere <dodofxp@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-31 01:47:17 -04:00
Elias Oltmanns 49ea3b0497 libata-core: make sure that ata_force_tbl is freed in case of an error
Fix a potential memory leak when ata_init() encounters an error.

Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-31 01:47:12 -04:00
Tejun Heo 2486fa561a libata: update atapi disable handling
Global and per-LLD ATAPI disable checks were done in the command issue
path probably because it was left out during EH conversion.  On
affected machines, this can cause lots of warning messages.  Move them
to where they belong - the probing path.

Reported by Chunbo Luo.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Chunbo Luo <chunbo.luo@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-31 01:47:05 -04:00
JosephChan@via.com.tw bfce5e0179 pata_via: add VX800 flag; add function for fixing h/w bugs
Add flag VIA_SATA_PATA for vx800, VX800 uses the same
chipset(0x0581/0x5324) as CX700, which has 1 PATA channel(Master/Slave)
and 1 SATA channel(Master/Slave) Add function <via_ata_tf_load>.  This is
to fix the internal bug of VIA chipsets, which will reset the device
register after changing the IEN bit in CTL register

Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-31 01:39:31 -04:00
Ben Dooks e8389f0c44 pata_ali: misplaced pci_dev_put()
The ali_init_one() function does a search for an isa_bridge,
but then fails to release it if the revision information was
not correctly found.

the problem comes from:
	isa_bridge = pci_get_device(...);
	if (isa_bridge && ...) {
		pci_dev_put(isa_bridge);
	}

where the pci_dev_put() is never called if isa_bridge
was valid but the extra checks on the chip-revision
fail to match.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-31 01:38:19 -04:00
Dmitry Baryshkov 6cab486029 [ARM] 5179/1: Replace obsolete IRQT_* and __IRQT_* values with IRQ_TYPE_*
IRQT_* and __IRQT_* were obsoleted long ago by patch [3692/1].
Remove them completely. Sed script for the reference:

s/__IRQT_RISEDGE/IRQ_TYPE_EDGE_RISING/g
s/__IRQT_FALEDGE/IRQ_TYPE_EDGE_FALLING/g
s/__IRQT_LOWLVL/IRQ_TYPE_LEVEL_LOW/g
s/__IRQT_HIGHLVL/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_RISING/IRQ_TYPE_EDGE_RISING/g
s/IRQT_FALLING/IRQ_TYPE_EDGE_FALLING/g
s/IRQT_BOTHEDGE/IRQ_TYPE_EDGE_BOTH/g
s/IRQT_LOW/IRQ_TYPE_LEVEL_LOW/g
s/IRQT_HIGH/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_PROBE/IRQ_TYPE_PROBE/g
s/IRQT_NOEDGE/IRQ_TYPE_NONE/g

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-27 09:46:18 +01:00
Linus Torvalds 93082f0b15 Fix ahci driver 'flags' type
The new type checking of the flags arguments to irqsave and friends
(commit 3f307891ce) pointed out this thing
with a big nice warning.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-25 10:56:36 -07:00
Benjamin Herrenschmidt 84c3d4aaec Merge commit 'origin/master'
Manual merge of:

	arch/powerpc/Kconfig
	arch/powerpc/kernel/stacktrace.c
	arch/powerpc/mm/slice.c
	arch/ppc/kernel/smp.c
2008-07-16 11:07:59 +10:00
Linus Torvalds b312bf359e Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  AHCI: Remove an unnecessary flush from ahci_qc_issue
  AHCI: speed up resume
  [libata] Add support for VPD page b1
  ata: endianness annotations in pata drivers
  libata-eh: update atapi_eh_request_sense() to take @dev instead of @qc
  [libata] sata_svw: update code comments relating to data corruption
  libata/ahci: enclosure management support
  libata: improve EH internal command timeout handling
  libata: use ULONG_MAX to terminate reset timeout table
  libata: improve EH retry delay handling
  libata: consistently use msecs for time durations
2008-07-15 11:18:10 -07:00
Benjamin Herrenschmidt 43d2548bb2 Merge commit '85082fd7cbe3173198aac0eb5e85ab1edcc6352c' into test-build
Manual fixup of:

	arch/powerpc/Kconfig
2008-07-15 15:44:51 +10:00
Benjamin Herrenschmidt 5b0504c0d7 Merge commit 'gcl/gcl-next' 2008-07-15 11:55:27 +10:00
Linus Torvalds dddec01eb8 Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (37 commits)
  splice: fix generic_file_splice_read() race with page invalidation
  ramfs: enable splice write
  drivers/block/pktcdvd.c: avoid useless memset
  cdrom: revert commit 22a9189 (cdrom: use kmalloced buffers instead of buffers on stack)
  scsi: sr avoids useless buffer allocation
  block: blk_rq_map_kern uses the bounce buffers for stack buffers
  block: add blk_queue_update_dma_pad
  DAC960: push down BKL
  pktcdvd: push BKL down into driver
  paride: push ioctl down into driver
  block: use get_unaligned_* helpers
  block: extend queue_flag bitops
  block: request_module(): use format string
  Add bvec_merge_data to handle stacked devices and ->merge_bvec()
  block: integrity flags can't use bit ops on unsigned short
  cmdfilter: extend default read filter
  sg: fix odd style (extra parenthesis) introduced by cmd filter patch
  block: add bounce support to blk_rq_map_user_iov
  cfq-iosched: get rid of enable_idle being unused warning
  allow userspace to modify scsi command filter on per device basis
  ...
2008-07-14 13:15:14 -07:00
Matthew Wilcox 2640d7c0b8 AHCI: Remove an unnecessary flush from ahci_qc_issue
In an I/O heavy workload (IOZone), ahci_qc_issue is the second-highest
consumer of CPU cycles.  Removing the flush gets us approximately 10%
bandwidth improvement.  I believe this to be because the CPU can start
queueing the next request instead of waiting for the readl() to flush the
writes to the device.  The flush isn't necessary because we're using a
'queue' metaphor; we don't guarantee the command has got to the device,
nor do we need to guarantee the command has got to the controller.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:34 -04:00
Zhang Rui 24920c8a63 AHCI: speed up resume
During resume, sleep 1 second to wait for the HBA reset
to finish is a waste of time.

According to the AHCI 1.2 spec,
We should poll the HOST_CTL register,
and return error if the host reset is not
finished within 1 second.

Test results show that the HBA reset can be done quickly(in usecs).
And this patch may save nearly 1 second during resume.

Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:33 -04:00
Matthew Wilcox 1e9dbc9291 [libata] Add support for VPD page b1
SCSI VPD page b1 reports the nominal rotation speed and physical size
of the device.  Devices that conform to ATA-8 can return this information
in words 217 and 168 of the identify data.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:33 -04:00
Harvey Harrison 6ad67403da ata: endianness annotations in pata drivers
drivers/ata/pata_qdi.c:142:9: warning: incorrect type in assignment (different base types)
drivers/ata/pata_qdi.c:142:9:    expected unsigned int [unsigned] [usertype] pad
drivers/ata/pata_qdi.c:142:9:    got restricted __le32 [usertype] <noident>
drivers/ata/pata_qdi.c:146:15: warning: cast to restricted __le32

drivers/ata/pata_winbond.c:110:9: warning: incorrect type in assignment (different base types)
drivers/ata/pata_winbond.c:110:9:    expected unsigned int [unsigned] [usertype] pad
drivers/ata/pata_winbond.c:110:9:    got restricted __le32 [usertype] <noident>
drivers/ata/pata_winbond.c:114:15: warning: cast to restricted __le32

drivers/ata/pata_legacy.c:310:9: warning: incorrect type in assignment (different base types)
drivers/ata/pata_legacy.c:310:9:    expected unsigned int [unsigned] [usertype] pad
drivers/ata/pata_legacy.c:310:9:    got restricted __le32 [usertype] <noident>
drivers/ata/pata_legacy.c:314:15: warning: cast to restricted __le32
drivers/ata/pata_legacy.c:752:11: warning: cast to restricted __le32
drivers/ata/pata_legacy.c:756:9: warning: incorrect type in assignment (different base types)
drivers/ata/pata_legacy.c:756:9:    expected unsigned int [unsigned] [addressable] [assigned] [usertype] pad
drivers/ata/pata_legacy.c:756:9:    got restricted __le32 [usertype] <noident>

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:33 -04:00
Tejun Heo 3eabddb8ed libata-eh: update atapi_eh_request_sense() to take @dev instead of @qc
Update atapi_eh_request_sense() to take @dev, @sense_buf and
@dfl_sense_key instead of taking @qc and extracting information from
it.  This change is to make the function more generic and allow it to
be called from other places.

While at it, make cdb initialization use initializer.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:33 -04:00
Pavel Machek ec6add9930 [libata] sata_svw: update code comments relating to data corruption
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:33 -04:00
Kristen Carlson Accardi 18f7ba4c2f libata/ahci: enclosure management support
Add Enclosure Management support to libata and ahci.

Signed-off-by:  Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:33 -04:00
Tejun Heo 87fbc5a060 libata: improve EH internal command timeout handling
ATA_TMOUT_INTERNAL which was 30secs were used for all internal
commands which is way too long when something goes wrong.  This patch
implements command type based stepped timeouts.  Different command
types can use different timeouts and each command type can use
different timeout values after timeouts.

ie. the initial timeout is set to a value which should cover most of
the cases but not too long so that run away cases don't delay things
too much.  After the first try times out, the second try can use
longer timeout and if that one times out too, it can go for full 30sec
timeout.

IDENTIFYs use 5s - 10s - 30s timeout and all other commands use 5s -
10s timeouts.

This patch significantly cuts down the needed time to handle failure
cases while still allowing libata to work with nut job devices through
retries.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:32 -04:00
Tejun Heo d8af0eb604 libata: use ULONG_MAX to terminate reset timeout table
This doesn't introduce any functional changes.  This is to make reset
timeout table consistent with to-be-added command timeout tables.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:32 -04:00
Tejun Heo 0a2c0f5615 libata: improve EH retry delay handling
EH retries were delayed by 5 seconds to ensure that resets don't occur
back-to-back.  However, this 5 second delay is superflous or excessive
in many cases.  For example, after IDENTIFY times out, there's no
reason to wait five more seconds before retrying.

This patch adds ehc->last_reset timestamp and record the timestamp for
the last reset trial or success and uses it to space resets by
ATA_EH_RESET_COOL_DOWN which is 5 secs and removes unconditional 5 sec
sleeps.

As this change makes inter-try waits often shorter and they're
redundant in nature, this patch also removes the "retrying..."
messages.

While at it, convert explicit rounding up division to DIV_ROUND_UP().

This change speeds up EH in many cases w/o sacrificing robustness.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:32 -04:00
Tejun Heo 341c2c958e libata: consistently use msecs for time durations
libata has been using mix of jiffies and msecs for time druations.
This is getting confusing.  As writing sub HZ values in jiffies is
PITA and msecs_to_jiffies() can't be used as initializer, unify unit
for all time durations to msecs.  So, durations are in msecs and
deadlines are in jiffies.  ata_deadline() is added to compute deadline
from a start time and duration in msecs.

While at it, drop now superflous _msec suffix from arguments and
rename @timeout to @deadline if it represents a fixed point in time
rather than duration.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:32 -04:00
Stephen Rothwell e6a9192d06 powerpc/pata_mpc52xx: use linux/of_platform.h instead of asm
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-07-12 12:10:52 -06:00
Zhang Rui 3c1e389634 libata-acpi: don't call sleeping function from invalid context
The problem is introduced by commit
664d080c41.

acpi_evaluate_integer is a sleeping function,
and it should not be called with spin_lock_irqsave.
https://bugzilla.redhat.com/show_bug.cgi?id=451399

Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-11 09:42:03 -04:00
Kai Krakow edb804713f Added Targa Visionary 1000 IDE adapter to pata_sis.c
This enables short 40-wire detection for my laptop thus
enabling UDMA/100.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-11 09:38:24 -04:00
Tejun Heo b344991ace libata-acpi: filter out DIPM enable
Some BIOSen enable DIPM via _GTF which causes command timeouts under
certain configuration.  This didn't occur on 2.6.25 because 2.6.25
defaulted to SRST, so _GTF wasn't executed during boot probe, so ahci
host reset disabled DIPM and as _GTF wasn't executed after SRST, DIPM
wasn't enabled.  On 2.6.26, hardreset is used during probe and after
probe _GTF is executed enabling DIPM and thus the failures.

This patch could theoretically disable DIPM on machines which used to
have it enabled on 2.6.25 but AFAIK ahci is currently the only driver
which uses SATA ACPI hierarchy (_SDD) and as the host reset would have
always disabled DIPM, this shouldn't happen.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-11 09:38:23 -04:00
Tejun Heo d28f87aa87 ahci: give another shot at clearing all bits in irq_stat
Commit ea0c62f7cf tried to clear all
bits in irq_stat but it didn't actually achieve that as irq_stat was
anded with port_map right after read.  This patch makes ahci driver
always use the unmasked value to clear irq_status.

While at it, add explanation on the peculiarities of ahci IRQ
clearing.

This was spotted by Linus Torvalds.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-05 13:05:37 -07:00
Mark Lord c7843e8f56 sata_mv: safer logic for limit_warnings
There is a miniscule chance that two separate host controllers
might be in sata_mv at the same time and manage to decrement
the static limit_warnings variable below zero.

Fix the comparison to deal with it.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-04 09:07:12 -04:00
Tejun Heo a836d3e882 libata-sff: improve HSM violation reporting
Improve SFF HSM violation reporting such that each HSM violation can
be distinguished using ehi_desc.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-04 09:06:02 -04:00
Tejun Heo ea0c62f7cf ahci: always clear all bits in irq_stat
Some AHCI controllers (ICH7 was reported) set pending bit in
HOST_IRQ_STAT for non-existent ports and when it's not cleared falls
into IRQ storm.  Always clear full irq_stat instead of only the bits
that are handled.  As nothing changes for recognized ports, the risk
of breaking things is pretty low.

Reported and verified by Philipp Thomas in the following suse
bugzilla.

https://bugzilla.novell.com/attachment.cgi?id=215692

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Philipp Thomas <pth@novell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-04 09:05:59 -04:00
Tejun Heo 464b3286b4 sata_sil24: add DID for another adaptec flavor
There's another DID used for Adaptec card.  Add it.

Reported by Travis Read.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Travis Read <ics@dark.net.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-04 09:05:43 -04:00
FUJITA Tomonori 27f8221af4 block: add blk_queue_update_dma_pad
This adds blk_queue_update_dma_pad to prevent LLDs from overwriting
the dma pad mask wrongly (we added blk_queue_update_dma_alignment due
to the same reason).

This also converts libata to use blk_queue_update_dma_pad instead of
blk_queue_dma_pad.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-07-04 09:52:13 +02:00
Tejun Heo 70a3143af8 sata_uli: hardreset is broken
sata_uli can't do hardresets reliably and lock up.  This went
unnoticed till now as softreset was the default and hardreset was only
used after softreset failed.

Reported by Christian Casteyde in bz#10860.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-27 02:57:48 -04:00
Linus Torvalds 06d5e334a4 Merge git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  BAST: Remove old IDE driver
  pcmcia ide kingston compactflash's have a new manufacturer id
  pcmcia: add another pata/ide ID
  pcmcia: add an pata/ide ID
  ide: increase timeout in wait_drive_not_busy()
  palm_bk3710: fix resource management
2008-06-20 12:46:47 -07:00
Kristoffer Ericson a17bf22023 pcmcia: add another pata/ide ID
Addition of Transcend 1GB 45x id so that it is properly detected.

[bart: fix typo in ide-cs's ID spotted by Alan Cox]

Signed-off-by: William Peters <w1ll14@gmail.com>
Signed-off-by: Kristoffer Ericson <Kristoffer_e1@hotmail.com>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-06-20 20:53:34 +02:00
Matt Reimer 74e23386b7 pcmcia: add an pata/ide ID
Add an id for:

product info: "M-Systems", "CF300", ""
manfid: 0x000a, 0x0000
function: 4 (fixed disk)

Signed-off-by: Matt Reimer <mreimer@vpop.net>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-06-20 20:53:34 +02:00
Tejun Heo 9a3b103c27 ahci: sis can't do PMP
From: Piter PUNK <piterpunk@slackware.com>

SiS AHCIs say they can do PMP but can't and fail detection if SRST w/
pmp==15 is used.  Turn off PMP support.

tj: added patch description, adapted patch to #upstream-fixes and
    renamed board_ahci_sis to board_ahci_nopmp.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-18 20:56:58 -04:00
Tejun Heo 040dee53a7 ata_piix: add TECRA M4 to broken suspend list
TOSHIBA also used "TECRA M4" in additon to "Tecra M4", add it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-18 20:28:17 -04:00
Ben Dooks cc18e0fea7 LIBATA: Add HAVE_PATA_PLATFORM to select PATA_PLATFORM driver
Add HAVE_PATA_PLATFORM to select the pata platform driver
to ensure that we do not end up with a long 'depends on' list
when other users of this driver turn up.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-18 20:28:00 -04:00
Mark Lord c6112bd86b sata_mv: warn on PIO with multiple DRQs
Chip errata sometimes prevents reliable use of PIO commands which involve
more than a single DRQ (data request).  In normal operation, libata should
not generate such PIO commands (uses DMA instead), but they could be sent
in via SG_IO from userspace.

A full workaround might be to break up such commands into sequences
of single DRQ ones, but that's just way too complex for something
that doesn't normally happen in real life.

So, allow the attempt (it often works, despite the errata),
but log the event for reference when somebody screams.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-18 20:27:58 -04:00
Mark Lord 3bd0a70ee9 sata_mv: enable async_notify for 60x1 Rev.C0 and higher
The early chipsets cannot safely handle Async Notification (AN),
but 6041/6081 chip revision "C0" (and newer) can handle it.

So allow AN for "C0" and higher.

This enables use of hotplug on PMP ports for the 6041/6081 PCI Rev.9 chips.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-18 20:27:55 -04:00
Tejun Heo 5895ef9a5b libata: don't check whether to use DMA or not for no data commands
There's no reason to check whether to use DMA or not for no data
commands.  Don't do it.  While at it, make local variable using_pio in
atapi_xlat() set iff ATAPI_PROT_PIO is going to be used and rename
ata_check_atapi_dma() to atapi_check_dma() for consistency.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-18 20:27:49 -04:00
Tejun Heo d799e083a8 ahci: jmb361 has only one port
JMB361 has only one port but reports it has two causing longish probe
failure on the second one.  Quirk it.

Reported by Gajo Petrovic in bz 10911.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Gajo Petrovic <gajo01@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-18 20:27:45 -04:00
Shane Huang bd17243a84 ahci: Workaround HW bug for SB600/700 SATA controller PMP support
There is one bug in ATI SATA PMP of SB600 and SB700 old revision, which leads
to soft reset failure. This patch can fix the bug.

Signed-off-by: Shane Huang <shane.huang@amd.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-13 02:46:55 -04:00
Tejun Heo e297d99e10 ahci: workarounds for mcp65
MCP65 ahci can do NCQ but doesn't set the CAP bit and rev A0 and A1
can't do MSI but have MSI capability.  Implement AHCI_HFLAG_YES_NCQ
and apply appropriate workarounds.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-13 02:46:17 -04:00
Hugh Dickins 6311c90a9e libata: fix G5 SATA broken on -rc5
Fix G5 SATA irq 18: nobody cared, reported on -rc5 by Olaf Hering:
fixlet to a57c1bade5 libata-sff:
Fix oops reported in kerneloops.org for pnp devices with no ctl

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Tested-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-05 08:36:37 -07:00
Alan Cox a57c1bade5 libata-sff: Fix oops reported in kerneloops.org for pnp devices with no ctl
- Make ata_sff_altstatus private so nobody uses it by mistake
- Drop the 400nS delay from it

Add

ata_sff_irq_status	-	encapsulates the IRQ check logic

This function keeps the existing behaviour for altstatus using devices. I
actually suspect the logic was wrong before the changes but -rc isn't the
time to play with that

ata_sff_sync		-	ensure writes hit the device

Really we want an io* operation for 'is posted' eg ioisposted(ioaddr) so
that we can fix the nasty delay this causes on most systems.

- ata_sff_pause		-	400nS delay

Ensure the command hit the device and delay 400nS

- ata_sff_dma_pause

Ensure the I/O hit the device and enforce an HDMA1:0 transition delay.
Requires altstatus register exists, BUG if not so we don't risk
corruption in MWDMA modes. (UDMA the checksum will save your backside in
theory)

The only other complication then is devices with their own handlers.
rb532 can use dma_pause but scc needs to access its own altstatus
register for internal errata workarounds so directly call the drivers own
altstatus function.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-04 06:40:41 -04:00
Mark Lord ba069e376c sata_mv: PHY_MODE4 cleanups
The handling for PHY_MODE4 was originally just cloned from the
Marvell proprietary driver (with their blessing).
But we can do better than that.

Tidy things up with some judicious mask definitions, to improve maintainability.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-04 06:29:11 -04:00
Colin Ian King e1fefea9cc [libata] ata_piix: more acer short cable quirks
Add ICH6 on ACER Aspire 1694WLMi to list of laptops that use short cables
rather than 80 wire

OriginalAuthor: Tiago Sousa
OriginalLocation: http://launchpadlibrarian.net/11627664/new.ich_laptop.short.cables.diff
Bug: #187121

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-04 06:29:06 -04:00
Holger Macht 664d080c41 [libata] ACPI: Properly handle bay devices in dock stations
* Differentiate between bay devices in dock stations and others:

 - When an ACPI_NOTIFY_EJECT_REQUEST appears, just signal uevent to
   userspace (that is when the optional eject button on a bay device is
   pressed/pulled) giving the possibility to unmount file systems and to
   clean up. Also, only send uevent in case we get an EJECT_REQUEST
   without doing anything else. In other cases, you'll get an add/remove
   event because libata attaches/detaches the device.

 - In case of a dock event, which in turn signals an
   ACPI_NOTIFY_EJECT_REQUEST, immediately detach the device, because it
   may already have been gone

* In case of an ACPI_NOTIFY_DEVICE/BUS_CHECK, evaluate _STA to check if
  the device has been plugged or unplugged. If plugged, hotplug it, if
  unplugged, just signal event to userspace
  (initial patch by Matthew Garrett <mjg59@srcf.ucam.org>)

* Call ACPI _EJ0 for detached devices

Signed-off-by: Holger Macht <hmacht@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-04 06:28:50 -04:00
peerchen 3072c379bc ahci: change the Device IDs of nvidia MCP7B AHCI controller in ahci.c
Change the partial Device IDs of nvidia MCP7B AHCI controller in ahci.c,
as the actual PCI IDs deployed in the field differed from the forecasted ones
preemptively placed in the driver.

Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-30 12:40:28 -04:00