The WMI tx status event timeout was not aligning with the
TX cleanup timer threshold value. Fix this to handle dropped
packets.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce the credit size for UB94/95 to fix target hangs.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k_htc: Fix AMPDU subframe handling" registered the maximum
subframe limit of the driver with mac80211, which was used in ADDBA
negotiation. While technically correct, this causes inter-operability issues
with a few APs. Revert to the older behavior to fix this.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BSSID/AID has to be set for the first associated station interface.
Subsequent interfaces may move out of assoc/disassoc status, in which
case, the BSSID has to be re-calculated from the available interfaces.
Also, ANI should be enabled or disabled based on the current opmode.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Choose the MY_BEACON filter only in case of a single interface.
Also, set the ATH9K_RX_FILTER_MCAST_BCAST_ALL filter in case
of interfaces.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The FW does absolutely nothing with the station flags,
so remove them. But keep the field around since it might
come in handy in the future.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove all the unsupported modes like FH, TURBO etc.
Since this requires a FW update, increase the fw version to 1.3
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is to fix an issue that the throughput of the higher priority
stream gets dropped when a lower priority stream is present.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we go through the entire for loop in
mwifiex_wmm_get_highest_priolist_ptr() and don't find any packets,
set highest_queued_prio to NO_PKT_PRIO_TID (< LOW_PRIO_TID).
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add checks to mwifiex_wmm_process_tx() loop so it doesn't re-enter
mwifiex_dequeue_tx_packet() to find it can't send.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds highest_queued_prio to track priority of packets as
they are enqueued so that mwifiex_wmm_get_highest_priolist_ptr()
starts checking at the first level where we have packets, instead of
the highest. The function also lowers priority value to the level
where first packet is found.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds tx_pkts_queued to track number of packets being
enqueued & dequeued so that mwifiex_wmm_lists_empty() evaluation
is lightweight.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a new generic gpio rfkill driver to support rfkill switches
which are controlled by gpios. The driver also supports passing in
data about the clock for the radio, so that when rfkill is blocking,
it can disable the clock.
This driver assumes platform data is passed from the board files to
configure it for specific devices.
Original-patch-by: Anantha Idapalapati <aidapalapati@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ad-hoc mode, beacon timers are configured differently compared to AP
mode, and (depending on the scenario) can vary enough to make the beacon
tasklet not detect slot 0 based on the TSF.
Since staggered beacons are not (and cannot be) used in ad-hoc mode, it
makes more sense to just hardcode slot 0 here, avoiding unnecessary
TSF reads and calculations.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 scan code adds separate BSS entries if the same BSS shows up
on multiple channels. However, sme implementation does not use the
frequency when fetching the BSS entry. Fix this by adding channel
information to cfg80211_roamed() and include it in cfg80211_get_bss()
calls.
Please note that drivers using cfg80211_roamed() need to be modified to
fully implement this fix. This commit includes only minimal changes to
avoid compilation issues; it maintains the old (broken) behavior for
most drivers. ath6kl was the only one that I could test, so I updated
it to provide the operating frequency in the roamed event.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The changes that were made to rtl8192ce when rtl8192cu was added broke
HT40. The errors included a typo in rtlwifi, a missing routine in
rtl8192ce and a missing callback of that routine in rtl8192c-common.
This patch fixes the regression reported in Bug #35082.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds proper RCU annotations to the mesh path
table code, and fixes a number of bugs in the code
that I found while checking the sparse warnings I
got as a result of the annotations.
Some things like the changes in mesh_path_add() or
mesh_pathtbl_init() only serve to shut up sparse,
but other changes like the changes surrounding the
for_each_mesh_entry() macro fix real RCU bugs in
the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The locking in mesh_{mpath,mpp}_table_grow not only
has an rcu_read_unlock() missing, it's also racy
(though really only technically since it's invoked
from a single function only) since it obtains the
new size of the table without any locking, so two
invocations of the function could attempt the same
resize.
Additionally, it uses synchronize_rcu() which is
rather expensive and can be avoided trivially here.
Modify the functions to only use the table lock
and use call_rcu() instead of synchronize_rcu().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 uses call_rcu() with functions that are
defined in the module, so it must use rcu_barrier()
at module exit time.
Luckily, this seems to not be a problem in practice
as module unload and unregistration takes a long
time and probably does multiple synchronize_rcu().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Gottfried Haider <gottfried.haider@gmail.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As long as no delay is required b/w channel change, scan work
is proceeding without scheduling a new work. In such case, we
can not abort scan work when the card was unplugged. This patch
completes the scanning immediately whenever the device goes down.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers shouldn't attempt to advertise support
for more than one IBSS interface since mac80211
doesn't support that. Check and return an error
from ieee80211_register_hw() in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to provide multiple interfaces for a single device,
the driver will be required to advertise all possible
interface configurations to the stack.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We free name "dev" for something generic (like dev abstraction layer).
Additionaly code is cleaner now, especially magic dev->dev-dev chains.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh paths are deleted via mesh_path_del() which properly
deactivates the timer associated to a mesh path. But if paths were
deleted by mesh_table_free(..., true) timers would not be deactivated.
This fixes this case.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* use proc_mkdir_mode() instead of create_proc_entry(S_IFDIR|...),
export proc_mkdir_mode() for that, oh well.
* don't supply S_IFREG to proc_create_data(), it's unnecessary
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: <stable@kernel.org>
Reported-by: Mark Davis <marked86@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex was using its own implementation of converting 802.11n
AMSDU to 802.3s. This patch removes mwifiex specific
implementation and uses existing ieee80211_amsdu_to_8023s
routine.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the devices that have already stripped IEEE 802.11
header from the AMSDU SKB can not use ieee80211_amsdu_to_8023s
routine. This patch enhances ieee80211_amsdu_to_8023s() API by
changing mandatory removing of IEEE 802.11 header from AMSDU
to optional.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These definitions need to be exposed now that we can set the peer link
states via NL80211_ATTR_STA_PLINK_STATE. They were already being
(opaquely) reported by NL80211_STA_INFO_PLINK_STATE.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we are not doing anything by tracking the number of pending frames.
bail out when we first find a pending frame in any one of the 10 queues.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
some times the rssi control descriptor for the main antenna may be
negative like that of alternate antenna, hence before incrementing
packet counts/rssi of main/alternate antenna make sure both main_rssi
and alt_rssi are positive only. this avoids wrong selection of antenna
due to diversity
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
configure fast diversity bias based on the antenna diversity group and
based on main/alt LNA configurations. also configure main antenna and
alternate antenna to gain-table 0 for diversity group 2(AR9485)
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
for the diversity group 2(AR9485) we swap the LNA's of main/ALT antenna
based on alternate antenna's rssi average in comparision with main
antenna's rssi, while for AR9285(antenna diversity group 0)we still
follow the older method of looking at the packet count in alternate
antenna
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9285 belongs to diversity group 0 and AR9485 belongs to diversity
group 2. Based on the diversity group we configure certain antenna
diversity paramaters such as lna1_lna2_delta and fast diversity
bias values. For AR9485 we have some gain table parameter which
selects the gain table 0/1 for main and alternate antenna
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
these are the two important modules that will be called by the antenna
diversity algorithm module in the rx. this will continuosly configure
the hardware based on the current diversity status obtained
from the algorithm
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* enable LNA-diversity, fast-diversity for AR9485 based on
the value read from EEPROM content
* if antenna diversity/combining is supported, set LNA1 for the main
antenna and LNA2 for the alternate antenna based on the new diversity
algorithm
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Cc: Luis Rodriguez <Luis.Rodriguez@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
define few registers and macros to configure/enable Antenna diversity
parameters in AR9485
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
read antenna diversity and combining information from the EEPROM.
Enable antenna diversity/combining feature only when both LNA
diversity and fast diversity are supported
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Tested-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this is necessary to support Antenna diversity and combining in new chip
sets such as AR9485, previously Antenna diversity support is available
only in AR9285
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The list_for_each_entry loop can fail, in which case the list element is
not removed from the list rfkill_fds. Since this list is not accessed by
the loop, the addition of &data->list into the list is just moved after the
loop.
The sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E,E1,E2;
identifier l;
@@
*list_add(&E->l,E1);
... when != E1
when != list_del(&E->l)
when != list_del_init(&E->l)
when != E = E2
*kfree(E);// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds sparse RCU annotations to most of
mac80211, only the mesh code remains to be
done.
Due the the previous patches, the annotations
are pretty simple. The only thing that this
actually changes is removing the RCU usage of
key->sta in debugfs since this pointer isn't
actually an RCU-managed pointer (it only has
a single assignment done before the key even
goes live). As that is otherwise harmless, I
decided to make it part of this patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During my quest to make mac80211 not have any RCU
warnings from sparse, I came across the a-MPDU code
again and it wasn't quite clear why it isn't racy.
So instead of assigning the tid_tx array with just
the spinlock held in ieee80211_start_tx_ba_session
use a separate temporary array protected only by
the spinlock and protect all assignments to the
"live" array by both the spinlock and the mutex so
that other code is easily verified to be correct.
Due to pointer assignment atomicity I don't think
this is a real issue, but I'm not sure, especially
on Alpha the current code might be problematic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the ability to advertise interface combinations in nl80211.
This allows the driver to indicate what the combinations are
that it supports. "Combinations" of just a single interface are
implicit, as previously. Note that cfg80211 will enforce that
the restrictions are met, but not for all drivers yet (once all
drivers are updated, we can remove the flag and enforce for all).
When no combinations are actually supported, an empty list will
be exported so that userspace can know if the kernel exported
this info or not (although it isn't clear to me what tools using
the info should do if the kernel didn't export it).
Since some interface types are purely virtual/software and don't
fit the restrictions, those are exposed in a new list of pure SW
types, not subject to restrictions. This mainly exists to handle
AP-VLAN and monitor interfaces in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enabling DEBUG_STRICT_USER_COPY_CHECKS causes the following
warning:
In file included from arch/x86/include/asm/uaccess.h:573,
from include/net/checksum.h:25,
from include/linux/skbuff.h:28,
from drivers/net/wireless/iwlwifi/iwl-agn-rs.c:28:
In function 'copy_from_user',
inlined from 'rs_sta_dbgfs_scale_table_write' at
drivers/net/wireless/iwlwifi/iwl-agn-rs.c:3099:
arch/x86/include/asm/uaccess_64.h:65:
warning: call to 'copy_from_user_overflow' declared with
attribute warning: copy_from_user() buffer size is not provably
correct
presumably due to buf_size being signed causing GCC to fail to
see that buf_size can't become negative.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan
Sujith Manoharan
Daniel Halperin
Marc Yang
Rhyland Klein
Felix Fietkau
Jouni Malinen
Rajkumar Manoharan
Larry Finger
Johannes Berg
Rafał Miłecki
Christian Lamparter
Javier Cardona
Alexey Dobriyan
John W. Linville
Yogesh Ashok Powar
Julia Lawall
Stephen Boyd