This patch support the new chipset rt3290 wifi implementation in rt2x00.
It initailize the related mac, bbp and rf register in startup phase.
And this patch modify the efuse read/write method for the different efuse data offset of rt3290.
Signed-off-by: Woody Hung <Woody.Hung@mediatek.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the eeprom parsing code overrides the sku
field directly with 11n_disable parameters, there's
no longer a need to keep a copy of this field.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The effect of using a short single-channel scan
to reset the radio is that scanning a channel
that isn't in use needs to re-tune the radio.
This means that the dwell time is irrelevant,
so use a shorter time.
While at it, clean up the code for this a bit.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My commit 26a7ca9a71 ("iwlwifi: refactor EEPROM reading/parsing")
broke the 11n_disable module parameter's BIT(0) to disable all HT
operation (using the other bits to disable aggregation only was
unaffected). Restore this by overriding the SKU when parsing the
EEPROM if the module parameter is set.
Reported-by: Matthijs Kooijman <matthijs@stdin.nl>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the device is doing an internal radio reset
scan, ROC can be rejected to the supplicant with
busy status which confuses it.
One option would be to queue the ROC and handle
it later, but since the radio reset scan is very
quick we can just wait for it to finish instead.
Also add a warning since we shouldn't run into
the case of having a scan active when requesting
a ROC in any other case since mac80211 will not
scan while ROC or ROC while scanning.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This feature needs to be disabled for all NICs.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This variable was accessed without taking the lock.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is really not needed, we already have a lock inside
the accesses to the prph.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is not needed since notif_wait_lock is never accessed
from IRQ.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is required by the op_mode API.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few op_mode of the op_mode API functions have requirements
on the running context of the caller. Document that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We introduced a lock here in ff1ffb850b ("iwlwifi: fix dynamic
loading"). But we missed an error path which needs an unlock.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug where no capabilites are parsed when the number
of firmware capability bits translate into fewer bytes than the host has
knowledge of. Instead just process number of capability bytes as
reported by the firmware.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
remove MCI_STATE_BT and use bt_state instead.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As p_data is unuse, lets remove it from ar9003_mci_state.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a MCI util function to send wlan channel info to BT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a utility function to set bluetooth version and remove
MCI_STATE_SET_BT_COEX_VERSION.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add utility functions to get and test GPM offset and
remove MCI_STATE*_GPM_OFFSET states.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
steps to recreate:
load latest ath9k driver with AR9485
stop the network-manager and wpa_supplicant
bring the interface up
Call Trace:
[<ffffffffa0517490>] ? ath_hw_check+0xe0/0xe0 [ath9k]
[<ffffffff812cd1e8>] __const_udelay+0x28/0x30
[<ffffffffa03bae7a>] ar9003_get_pll_sqsum_dvc+0x4a/0x80 [ath9k_hw]
[<ffffffffa05174eb>] ath_hw_pll_work+0x5b/0xe0 [ath9k]
[<ffffffff810744fe>] process_one_work+0x11e/0x470
[<ffffffff8107530f>] worker_thread+0x15f/0x360
[<ffffffff810751b0>] ? manage_workers+0x230/0x230
[<ffffffff81079af3>] kthread+0x93/0xa0
[<ffffffff815fd3a4>] kernel_thread_helper+0x4/0x10
[<ffffffff81079a60>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff815fd3a0>] ? gs_change+0x13/0x13
ensure that the PLL-WAR for AR9485/AR9340 is executed only if the STA is
associated (or) IBSS/AP mode had started beaconing. Ideally this WAR
is needed to recover from some rare beacon stuck during stress testing.
Before the STA is associated/IBSS had started beaconing, PLL4(0x1618c)
always seem to have zero even though we had configured PLL3(0x16188) to
query about PLL's locking status. When we keep on polling infinitely PLL4's
8th bit(ie check for PLL locking measurements is done), machine hangs
due to softlockup.
fixes https://bugzilla.redhat.com/show_bug.cgi?id=811142
Reported-by: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: stable@vger.kernel.org
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Reset duty cycle before updating btcoex scheme. Otherwise duty cycle
reaches max limit and never be reduced again
* Adjust duty cycle with proper BDR profile value
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As btcoex scheme updation might sleep, remove the function call
from tasklet context and queue it up as a separate work.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
btcoex periord is converted into micro seconds during initialization
and converted back to milli seconds while starting timer. As MCI code
handles btcoex period in msec, lets keep the btcoex timer in msec and
convert them into other form whenever needed.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies profile management utility functions.
* Separate find_profile from add/del functions
* Return correct values when the profile list is empty or
profile is ot found
* flush the profiles when there are entries in the list
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
let us process MCI interrupts only when BTCOEX is enabled to avoid
processing bogus interrupts.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After a full reset, mci_reset will put LNA update to the setting
for 2G mode. Those registers need to be forced to update when
the channel is in 5G.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both "MAC Warm Reset" and "MCI Reset Rx" will reset GPM HW write_ptr.
We should check software cached write_ptr against HW write_ptr before
reset. Otherwise the pending DMA data will be lost.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW statemachine is sometimes found stuck in the state
WL_LNA_CTRL_DISABLE when BT is in sleep, which will cause
TX_HOLD always asserted and resmgr stuck in PENDING_TX state
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not doing so, could cause imbalance in powersave count.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Choose legacy rate as the last rate of Multi Rate Retry series
if and only if the last selected rate is MCS and having higher
PER rate. The current code fills a legacy rate as last one even
though the previous rates in the series are having good PER value.
This could limit the aggregation that affects the uplink performance.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust quick_drop value in the baseband AGC register to
improve RX in HT20 mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The structure brcmf_sdio contains a number of counters that are useful
for debugging. These were not available in user-space. This patch
exposes them in debugfs under the filename 'counters'.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds debugfs support to brcmfmac. It provide helper functions
to setup the debugfs folder structure for the driver, which has following
hierarchy:
<debugfs_mount>/brcmfmac/<dev_name>/
ie.: /sys/kernel/debug/brcmfmac/mmc0:0001:2/
The new source file provides functions to create and remove the two
folders and a function to retrieve the device-specific folder so files
can be created in it.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes potential NULL pointer dereference in ampdu. This
was found running smatch static code checker. Smatch warning says:
drivers/net/wireless/brcm80211/brcmsmac/ampdu.c:741 brcms_c_sendampdu()
warn: variable dereferenced before check 'p'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcms_set_hint() does not add any functionality
so regulatory_hint() can be called directly. The error value
has been removed from the message when regulatory_hint() fails.
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
steps to recreate:
load latest ath9k driver with AR9485
stop the network-manager and wpa_supplicant
bring the interface up
Call Trace:
[<ffffffffa0517490>] ? ath_hw_check+0xe0/0xe0 [ath9k]
[<ffffffff812cd1e8>] __const_udelay+0x28/0x30
[<ffffffffa03bae7a>] ar9003_get_pll_sqsum_dvc+0x4a/0x80 [ath9k_hw]
[<ffffffffa05174eb>] ath_hw_pll_work+0x5b/0xe0 [ath9k]
[<ffffffff810744fe>] process_one_work+0x11e/0x470
[<ffffffff8107530f>] worker_thread+0x15f/0x360
[<ffffffff810751b0>] ? manage_workers+0x230/0x230
[<ffffffff81079af3>] kthread+0x93/0xa0
[<ffffffff815fd3a4>] kernel_thread_helper+0x4/0x10
[<ffffffff81079a60>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff815fd3a0>] ? gs_change+0x13/0x13
ensure that the PLL-WAR for AR9485/AR9340 is executed only if the STA is
associated (or) IBSS/AP mode had started beaconing. Ideally this WAR
is needed to recover from some rare beacon stuck during stress testing.
Before the STA is associated/IBSS had started beaconing, PLL4(0x1618c)
always seem to have zero even though we had configured PLL3(0x16188) to
query about PLL's locking status. When we keep on polling infinitely PLL4's
8th bit(ie check for PLL locking measurements is done), machine hangs
due to softlockup.
fixes https://bugzilla.redhat.com/show_bug.cgi?id=811142
Reported-by: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: stable@vger.kernel.org [3.0+]
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stop connection monitor poll during disassociation.
This clears the polling flags and if a scan was
deferred it will be run.
Without this fix, if a scan was deferred due to
connection monitoring while disassociation happens,
this scan blocks further scan requests until interface
down/up which causes problems connecting to another AP.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise, we might call the driver callback before
the interface was uploaded.
Solves the following warning:
WARNING: at net/mac80211/driver-ops.h:12 ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211]()
wlan0: Failed check-sdata-in-driver check, flags: 0x0
Modules linked in: wlcore_sdio wl12xx wl18xx wlcore mac80211 cfg80211 [last unloaded: cfg80211]
[<c001b964>] (unwind_backtrace+0x0/0x12c) from [<c0495550>] (dump_stack+0x20/0x24)
[<c0495550>] (dump_stack+0x20/0x24) from [<c003ee28>] (warn_slowpath_common+0x5c/0x74)
[<c003ee28>] (warn_slowpath_common+0x5c/0x74) from [<c003eefc>] (warn_slowpath_fmt+0x40/0x48)
[<c003eefc>] (warn_slowpath_fmt+0x40/0x48) from [<bf5c1ad0>] (ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211])
[<bf5c1ad0>] (ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211]) from [<bf575960>] (nl80211_set_tx_bitrate_mask+0x350/0x358 [cfg80211])
[<bf575960>] (nl80211_set_tx_bitrate_mask+0x350/0x358 [cfg80211]) from [<c03e9e94>] (genl_rcv_msg+0x1a8/0x1e8)
[<c03e9e94>] (genl_rcv_msg+0x1a8/0x1e8) from [<c03e9164>] (netlink_rcv_skb+0x5c/0xc0)
[<c03e9164>] (netlink_rcv_skb+0x5c/0xc0) from [<c03e9ce0>] (genl_rcv+0x28/0x34)
[<c03e9ce0>] (genl_rcv+0x28/0x34) from [<c03e8e74>] (netlink_unicast+0x158/0x234)
[<c03e8e74>] (netlink_unicast+0x158/0x234) from [<c03e93e0>] (netlink_sendmsg+0x218/0x298)
[<c03e93e0>] (netlink_sendmsg+0x218/0x298) from [<c03b4e5c>] (sock_sendmsg+0xa4/0xc0)
[<c03b4e5c>] (sock_sendmsg+0xa4/0xc0) from [<c03b5af4>] (__sys_sendmsg+0x1d8/0x254)
[<c03b5af4>] (__sys_sendmsg+0x1d8/0x254) from [<c03b5ca8>] (sys_sendmsg+0x4c/0x70)
[<c03b5ca8>] (sys_sendmsg+0x4c/0x70) from [<c0013980>] (ret_fast_syscall+0x0/0x3c)
Note that calling the driver can also result
in undefined behaviour since it doesn't have
to deal with calls while down.
Signed-off-by: Eliad Peller <eliad@wizery.com>
[removed timestamps, added note - Johannes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Woody Hung
John W. Linville
Johannes Berg
Emmanuel Grumbach
Dan Carpenter
Kalle Valo
Thomas Pedersen
Rajkumar Manoharan
Mohammed Shafi Shajakhan
Sujith Manoharan
Arend van Spriel
David Spinadel
Eliad Peller