Compile error reported by Jim Davis on netdev.
ip6_sk_accept_pmtu() needs net/ip6_route.h
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hauke Mehrtens says:
====================
b44: add support for external PHY
This adds support for an external phy connected to the mac controlled
by b44. This is used on home routers of the BCM47xx line where this MAC
core was used and is contended to an external switch core through MII.
These patches are in OpenWrt for some time and are tested by different
users with different devices.
The publicly available Programmer's Reference Guide for some of these
chips help making this patch it would be nice to have such a
documentation for more Broadcom Chips like some SoCs.
https://www.broadcom.com/collateral/pg/440X-PG02-R.pdf
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
The ADM6996L switch and some Broadcom switches with two MII interfaces
like the BCM5325F connected to two MACs on the SoC, used on some
routers do not return a valid value when reading the PHY id register
and Linux thinks there is no PHY at all, but that is wrong.
This patch registers a fixed phy in the arch code and then searches it
when there is no other phy in the Ethernet driver code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
b44_phy_reset() will fail for an external PHY and only work with the
internal PHY, this was an old workaround when the detection of an
external switch based on the PHY address failed and it is not needed
any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch we can not access the PHY when the MAC is switched
off. This PHY access is needed to configure the switch, which is done
through PHY registers.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the older home routers based on the Broadcom BCM47XX SoC series
are using a MAC that is supported by b44. On most of these routers not
the internal PHY of this MAC core is used, but a switch sometimes on an
external chip or integrated into the same SoC as the Ethernet core.
For this switch a special PHY driver is needed which should not be
integrated into b44 as the same switches are also used by other
Broadcom home networking SoCs which are using different Ethernet MAC
drivers. This was tested with the b53 switch driver which is currently
on its way to mainline.
If the internal PHY is not used, b44 will now search on the MDIO bus
for a phy and use the Linux phylib subsystem to register a driver.
Support for the internal PHY must stay here, because there are some
device which are suing the internal phy.
With this patch we scan the mdio bus when the sprom or nvram says that
the PHY address is 30, if a PHY was found at this address b44 uses it.
This was tested with a BCM4704, BCM4712 and BCM5354.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next patch will add these functions for phylib, and we should
rename the old ones before. This now indicates that these functions are
used for the mdio registers and on the mii interface.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the phy address is 31, this means that there is no PHY connected
to this MAC at all, no internal and no external PHY. Reading these PHY
registers causes a system reset on some routers.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY address 30 means there is no local PHY, but there could be an
external PHY like a switch connected via MII. This is the case on most
embedded home routers where this driver is used.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ethernet core supported by b44 supports an internal PHY integrated
into the mac core, which is supported by the b44 driver and an external
PHY to which the mac core is connected. This external PHY could be a
switch connected through MII, which is often the case when this core is
used on home routers. The usage of an external PHY was assumed when the
PHY address 30 was used and an internal PHY was assumed when the PHY
address was different. To verify that b44_phy_reset() was called and
checked if it worked, otherwise PHY address 30 was assumed, an external
PHY. It is better to check the register which says which PHY is
connected to the MAC instead of checking the PHY address.
The interface to an external PHY was only activated when this register
was set.
This also changes B44_FLAG_INTERNAL_PHY to B44_FLAG_EXTERNAL_PHY, it is
easier to check.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem noticed a TCP_RR regression caused by TCP autocorking
on a Mellanox test bed. MLX4_EN_TX_COAL_TIME is 16 us, which can be
right above RTT between hosts.
We can receive a ACK for a packet still in NIC TX ring buffer or in a
softnet completion queue.
Fix this by always pushing the skb if it is at the head of write queue.
Also, as TX completion is lockless, it's safer to perform sk_wmem_alloc
test after setting TSQ_THROTTLED.
erd:~# MIB="MIN_LATENCY,MEAN_LATENCY,MAX_LATENCY,P99_LATENCY,STDDEV_LATENCY"
erd:~# ./netperf -H remote -t TCP_RR -- -o $MIB | tail -n 1
(repeat 3 times)
Before patch :
18,1049.87,41004,39631,6295.47
17,239.52,40804,48,2912.79
18,348.40,40877,54,3573.39
After patch :
18,22.84,4606,38,16.39
17,21.56,2871,36,13.51
17,22.46,2705,37,11.83
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: f54b311142 ("tcp: auto corking")
Signed-off-by: David S. Miller <davem@davemloft.net>
list_for_each_entry(a, &act_base, head) doesn't
exit with a = NULL if we reached the end of the list.
tcf_unregister_action(), tc_lookup_action_n() and tc_lookup_action()
need fixes.
Remove tc_lookup_action_id() as its unused and not worth 'fixing'
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 1f747c26c4 ("net_sched: convert tc_action_ops to use struct list_head")
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
list_for_each_entry(t, &tcf_proto_base, head) doesn't
exit with t = NULL if we reached the end of the list.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 3627287463 ("net_sched: convert tcf_proto_ops to use struct
list_head")
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes:
1) pass mask rather than size to tcf_hashinfo_init()
2) the cleanup should be in reversed order in mirred_cleanup_module()
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Fixes: 369ba56787 ("net_sched: init struct tcf_hashinfo at register time")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tan Xiaojun says:
====================
bridge: cleanup and fix checkpatch errors
Clean up and fix some checkpatch errors in bridge driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
That open brace { should be on the previous line.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spaces required before the open parenthesis '(', before the open
brace '{', after that ',' and around that '?/:'.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return is not a function, parentheses are not required.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because err is always negative, remove unnecessary condition
judgment.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov says:
====================
Add PHY IRQ support to the 'sh_eth' driver
This patchset adds support for passing PHY's IRQ to the 'sh_eth' driver from
the platform code and removes now useless code that hinders the PHY IRQ handing
by philib.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need anymore to call phy_init_hw() to reset/resume the PHY from the
driver, as the call chain in phylib already has reached it, and so reset/resumed
the PHY (even resuming it twice). This duplicate reset is not only needless, it
e.g. clears the PHY's interrupt enables just setup by phylib and so prevents the
expected IRQs from the PHY.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the platform code to pass PHY's IRQ to the driver. Print this IRQ along
with the other PHY datails in sh_eth_phy_init().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai says:
====================
net/mlx4: Mellanox driver update 08-12-2013
This patchset contains:
1. Support in ndo_get_phys_port_id added by Hadar.
2. Change the driver to use by default CQE/EQE size of 64 bytes done by Eyal.
This doubles the packet-rate of the NIC.
3. Configure the XPS queue mapping on driver load - added by Ido.
4. Fixes for some small bugs done by Jenny and Matan
Patchset was applied and tested against commit: "2372175 lib: hash: follow-up
fixups for arch hash"
Changes from V1:
- Removed Patch 10 "net/mlx4_en: Fix Supported/Advertised link mode reported by
ethtool". This patch is needed to be rewritten from scratch and I wouldn't
like it to block the rest of the patches in this set.
Also, fix to Kconfig suggested by Ben will be sent in next patchset.
Changes from V0:
- Found some issues in "Reuse memory in RX flow" patch from V0.
Removing this patch from the patchset till analyzed and fixed.
- Fix some coding style issues in patch 6 "Configure the XPS queue mapping on
driver load"
- Changed patch 9 "Add NAPI support for transmit side" to use NAPI_POLL_WEIGHT
instead of MLX4_EN_TX_BUDGET
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to validate port number at mlx4_promisc_qp() before use.
Since port number is extracted from gid, as a cooked or corrupted gid
could lead to a crash.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NAPI for TX side,
implement its support and provide NAPI callback.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MLX4_DEV_EVENT_SLAVE_INIT and MLX4_DEV_EVENT_SLAVE_SHUTDOWN
events used by Hypervisor to inform the PPF IB driver that
IB para-virtualization must be initialized/destroyed for a slave.
If this event is catched by ETH VF annoying but harmless error message
is printed into dmesg. Remove dmesg prints for these events.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To achieve out of the box performance default is to use 64 byte CQE/EQE.
In tests that we conduct in our labs, we achieved a performance
improvement of twice the message rate. For older VF/libmlx4 support,
enable_64b_cqe_eqe must be set to 0 (disabled).
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only TX rings of User Piority 0 are mapped.
TX rings of other UP's are using UP 0 mapping.
XPS is not in use when num_tc is set.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the port GUID read from the firmware to identify the physical port.
This port identifier is available via ndo_get_phys_port_id for both PF
and VF net-devices.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the infrastructure needed to support ndo_get_phys_port_id which
allows users to identify to which physical port a net-device is connected
to by reading a unique port id.
This will work for VFs and PFs.
The driver uses a new device capability - phys_port_id, The PF driver
reads the port phys_port_id from Firmware and stores it. The VF driver
reads the port phys_port_id from the PF using QUERY_FUNC_CAP command.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set nic_info field in QUERY_FUNC_CAP, which designates
supplementary NIC information is provided by the hypervisor.
When set, the following fields are valid: nic_num_rings,
nic_indirection_tbl_sz, cur_mac and phys_port_id.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use correct names for QUERY_FUNC_CAP fields: flags0 and flags1.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All mailboxes are already zeroed by commit:
571b8b9 net/mlx4_core: Initialize all mailbox buffers to zero before use
Remove explicit zero set for force mac and force vlan fields in
mlx4_QUERY_FUNC_CAP_wrapper
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given we allocate memory for each cpu, we can do this
using NUMA affinities, instead of using NUMA policies
of the process changing flow_limit_cpu_bitmap value.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch marks the function il_clear_traffic_stats() in debug.c as
static because they are not used outside this file.
Thus, it also removes the following warnings in
wireless/iwlegacy/debug.c:
drivers/net/wireless/iwlegacy/debug.c:35:1: warning: no previous prototype for ‘il_clear_traffic_stats’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch marks the function il4965_ucode_rx_stats_read(),
il4965_ucode_tx_stats_read() and il4965_ucode_general_stats_read() in
4965-debug.c as static because they are not used outside this file.
Thus, it also removes the following warnings in
wireless/iwlegacy/4965-debug.c:
drivers/net/wireless/iwlegacy/4965-debug.c:59:1: warning: no previous prototype for ‘il4965_ucode_rx_stats_read’ [-Wmissing-prototypes]
drivers/net/wireless/iwlegacy/4965-debug.c:471:1: warning: no previous prototype for ‘il4965_ucode_tx_stats_read’ [-Wmissing-prototypes]
drivers/net/wireless/iwlegacy/4965-debug.c:637:1: warning: no previous prototype for ‘il4965_ucode_general_stats_read’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch marks the function il3945_ucode_rx_stats_read(),
il3945_ucode_tx_stats_read() and il3945_ucode_general_stats_read() in
3945-debug.c as static because they are not used outside this file.
Thus, it also removes the following warnings in
wireless/iwlegacy/3945-debug.c:
drivers/net/wireless/iwlegacy/3945-debug.c:52:1: warning: no previous prototype for ‘il3945_ucode_rx_stats_read’ [-Wmissing-prototypes]
drivers/net/wireless/iwlegacy/3945-debug.c:317:1: warning: no previous prototype for ‘il3945_ucode_tx_stats_read’ [-Wmissing-prototypes]
drivers/net/wireless/iwlegacy/3945-debug.c:407:1: warning: no previous prototype for ‘il3945_ucode_general_stats_read’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new header file include/net/Space.h which contains
prototype declaration of sbni_probe().
Include the new header file in drivers/net/Space.c and
drivers/net/wan/sbni.c because they use this function.
This eliminates the following warning in wan/sbni.c:
drivers/net/wan/sbni.c:224:12: warning: no previous prototype for ‘sbni_probe’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch marks the function stmmac_pltfr_freeze() and
stmmac_pltfr_restore() in stmmac_platform.c as static because they are
not used outside this file.
Thus, it also removes the following warnings in
ethernet/stmicro/stmmac/stmmac_platform.c:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:222:5: warning: no previous prototype for ‘stmmac_pltfr_freeze’ [-Wmissing-prototypes]
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:236:5: warning: no previous prototype for ‘stmmac_pltfr_restore’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch marks the function qlcnic_83xx_clear_legacy_intr_mask(),
qlcnic_83xx_set_legacy_intr_mask() and
qlcnic_83xx_enable_legacy_msix_mbx_intr() in qlcnic_83xx_hw.c as static
because they are not used outside this file.
Thus, it also removes the following warnings
in ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c:318:13: warning: no previous prototype for ‘qlcnic_83xx_clear_legacy_intr_mask’ [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c:323:13: warning: no previous prototype for ‘qlcnic_83xx_set_legacy_intr_mask’ [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c:343:13: warning: no previous prototype for ‘qlcnic_83xx_enable_legacy_msix_mbx_intr’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch marks the function qlcnic_enable_tx_intr(),
qlcnic_83xx_enable_tx_intr() and qlcnic_83xx_disable_tx_intr() in
qlcnic_io.c as static because they are not used outside this file.
Thus, it also removes the following warnings in
ethernet/qlogic/qlcnic/qlcnic_io.c:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_io.c:130:13: warning: no previous prototype for ‘qlcnic_enable_tx_intr’ [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_io.c:147:13: warning: no previous prototype for ‘qlcnic_83xx_enable_tx_intr’ [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_io.c:153:13: warning: no previous prototype for ‘qlcnic_83xx_disable_tx_intr’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2013-12-19
1) Use the user supplied policy index instead of a generated one
if present. From Fan Du.
2) Make xfrm migration namespace aware. From Fan Du.
3) Make the xfrm state and policy locks namespace aware. From Fan Du.
4) Remove ancient sleeping when the SA is in acquire state,
we now queue packets to the policy instead. This replaces the
sleeping code.
5) Remove FLOWI_FLAG_CAN_SLEEP. This was used to notify xfrm about the
posibility to sleep. The sleeping code is gone, so remove it.
6) Check user specified spi for IPComp. Thr spi for IPcomp is only
16 bit wide, so check for a valid value. From Fan Du.
7) Export verify_userspi_info to check for valid user supplied spi ranges
with pfkey and netlink. From Fan Du.
8) RFC3173 states that if the total size of a compressed payload and the IPComp
header is not smaller than the size of the original payload, the IP datagram
must be sent in the original non-compressed form. These packets are dropped
by the inbound policy check because they are not transformed. Document the need
to set 'level use' for IPcomp to receive such packets anyway. From Fan Du.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman says:
====================
bonding: add even more netlink attributes
The following series implements five more bonding netlink attributes:
num_grat_arp|num_unsol_na
all_slaves_active
min_links
lp_interval
packets_per_slave
Tested with modified iproute2 to verify attributes can be set at bond creation
time or set later. Verified sysfs interface to attributes continues to work.
I have one more set after this one for all of the 802.3ad attributes. Whew.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BOND_PACKETS_PER_SLAVE to allow get/set of bonding parameter
packets_per_slave via netlink.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BOND_LP_INTERVAL to allow get/set of bonding parameter
lp_interval via netlink.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BOND_MIN_LINKS to allow get/set of bonding parameter
min_links via netlink.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BOND_ALL_SLAVES_ACTIVE to allow get/set of bonding parameter
all_slaves_active via netlink.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BOND_NUM_PEER_NOTIF to allow get/set of bonding parameter
num_grat_arp via netlink. Bonding parameter num_unsol_na is
synonymous with num_grat_arp, so add only one netlink attribute
to represent both bonding parameters.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
sfeldma@cumulusnetworks.com