Some USB device / host controller combinations seem to have problems
with Link Power Management. For example, Steinar found that his xHCI
controller wouldn't handle bandwidth calculations correctly for two
video cards simultaneously when LPM was enabled, even though the bus
had plenty of bandwidth available.
This patch introduces a new quirk flag for devices that should remain
disabled for LPM, and creates quirk entries for Steinar's devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to USB 2 specs ports need to signal resume for at least 20ms,
in practice even longer, before moving to U0 state.
Both host and devices can initiate resume.
On device initiated resume, a port status interrupt with the port in resume
state in issued. The interrupt handler tags a resume_done[port]
timestamp with current time + USB_RESUME_TIMEOUT, and kick roothub timer.
Root hub timer requests for port status, finds the port in resume state,
checks if resume_done[port] timestamp passed, and set port to U0 state.
On host initiated resume, current code sets the port to resume state,
sleep 20ms, and finally sets the port to U0 state. This should also
be changed to work in a similar way as the device initiated resume, with
timestamp tagging, but that is not yet tested and will be a separate
fix later.
There are a few issues with this approach
1. A host initiated resume will also generate a resume event. The event
handler will find the port in resume state, believe it's a device
initiated resume, and act accordingly.
2. A port status request might cut the resume signalling short if a
get_port_status request is handled during the host resume signalling.
The port will be found in resume state. The timestamp is not set leading
to time_after_eq(jiffies, timestamp) returning true, as timestamp = 0.
get_port_status will proceed with moving the port to U0.
3. If an error, or anything else happens to the port during device
initiated resume signalling it will leave all the device resume
parameters hanging uncleared, preventing further suspend, returning
-EBUSY, and cause the pm thread to busyloop trying to enter suspend.
Fix this by using the existing resuming_ports bitfield to indicate that
resume signalling timing is taken care of.
Check if the resume_done[port] is set before using it for timestamp
comparison, and also clear out any resume signalling related variables
if port is not in U0 or Resume state
This issue was discovered when a PM thread busylooped, trying to runtime
suspend the xhci USB 2 roothub on a Dell XPS
Cc: stable <stable@vger.kernel.org>
Reported-by: Daniel J Blueman <daniel@quora.org>
Tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hopefully final set of fixes for v4.4 release cycle.
There's a fix for a regression on dwc3 caused by recent changes to how
transfers are started. We're not pre-starting interrupt endpoints
anymore.
A NULL pointer dereference fix for the MSM phy driver.
The UVC gadget got a minor fix for permissions to its configfs
attributes and, finally, two fixes for MUSB. A fix for PM runtime when
MUSB returns EPROBE_DEFER and a fix to actually return an error in case
we can't initialize a DMA engine.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o5zI
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for-v4.4-rc5
Hopefully final set of fixes for v4.4 release cycle.
There's a fix for a regression on dwc3 caused by recent changes to how
transfers are started. We're not pre-starting interrupt endpoints
anymore.
A NULL pointer dereference fix for the MSM phy driver.
The UVC gadget got a minor fix for permissions to its configfs
attributes and, finally, two fixes for MUSB. A fix for PM runtime when
MUSB returns EPROBE_DEFER and a fix to actually return an error in case
we can't initialize a DMA engine.
Signed-off-by: Felipe Balbi <balbi@ti.com>
76e0da3 "usb-gadget/uvc: use per-attribute show and store methods"
removed write permission for writeable attributes. Correct attribute
permissions.
Fixes: 76e0da3 "usb-gadget/uvc: use per-attribute show and store methods"
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If musb_init_controller fails at musb_platform_init, we have already
called pm_runtime_irq_safe for musb and that causes the pm runtime count
to be enabled for parent before the parent has completed initialization.
This causes pm to stop working as on unload nothing gets idled.
This issue can be reproduced at least with:
# modprobe omap2430
HS USB OTG: no transceiver configured
musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
# modprobe phy-twl4030-usb
# rmmod omap2430
And after the steps above omap2430 will block deeper idle states on
omap3.
To fix this, let's not enable pm runtime until we need to and the
parent has been initialized. Note that this does not fix the issue of
PM being broken for musb during runtime.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Even if the probability of this case is very low, fixing it made
static analyzers happy.
Solving this with of_device_get_match_data made also code simplier.
Reported-by: coverity (CID 1324133)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The interrupt handler, ohci_hcd_at91_overcurrent_irq may be called right
after registration. At that time, pdev->dev.platform_data is not yet set,
leading to a NULL pointer dereference.
Fixes: e4df92279f (USB: host: ohci-at91: merge loops in ohci_hcd_at91_drv_probe)
Reported-by: Peter Rosin <peda@axentia.se>
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: stable@vger.kernel.org # 4.3+
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My recent Intel box is spewing these messages:
xhci_hcd 0000:00:14.0: xHCI Host Controller
xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: xHCI Host Controller
usb usb2: Manufacturer: Linux 4.3.0+ xhci-hcd
usb usb2: SerialNumber: 0000:00:14.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
usb: failed to peer usb2-port2 and usb1-port1 by location (usb2-port2:none) (usb1-port1:usb2-port1)
usb usb2-port2: failed to peer to usb1-port1 (-16)
usb: port power management may be unreliable
usb: failed to peer usb2-port3 and usb1-port1 by location (usb2-port3:none) (usb1-port1:usb2-port1)
usb usb2-port3: failed to peer to usb1-port1 (-16)
usb: failed to peer usb2-port5 and usb1-port1 by location (usb2-port5:none) (usb1-port1:usb2-port1)
usb usb2-port5: failed to peer to usb1-port1 (-16)
usb: failed to peer usb2-port6 and usb1-port1 by location (usb2-port6:none) (usb1-port1:usb2-port1)
usb usb2-port6: failed to peer to usb1-port1 (-16)
Diving into the acpi tables, I noticed the EHCI hub has 12 ports while the XHCI
hub has 8 ports. Most of those ports are of connect type USB_PORT_NOT_USED
(including port 1 of the EHCI hub).
Further the unused ports have location data initialized to 0x80000000.
Now each unused port on the xhci hub walks the port list and finds a matching
peer with port1 of the EHCI hub because the zero'd out group id bits falsely match.
After port1 of the XHCI hub, each following matching peer will generate the
above warning.
These warnings seem to be harmless for this scenario as I don't think it
matters that unused ports could not create a peer link.
The attached patch utilizes that assumption and just turns the pr_warn into
pr_debug to quiet things down.
Tested on my Intel box.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if a full speed hub connects to a high speed hub which
supports MTT, the MTT field of its slot context will be set
to 1 when xHCI driver setups an xHCI virtual device in
xhci_setup_addressable_virt_dev(); once usb core fetch its
hub descriptor, and need to update the xHC's internal data
structures for the device, the HUB field of its slot context
will be set to 1 too, meanwhile MTT is also set before,
this will cause configure endpoint command fail, so in the
case, we should clear MTT to 0 for full speed hub according
to section 6.2.2
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a memory leak because acpi_evaluate_dsm() actually returns an
object which the caller is supposed to release. Fix this by calling
ACPI_FREE() for the returned object (this expands to kfree() so passing
NULL there is fine as well).
While there correct indentation in !CONFIG_ACPI case.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # v4.2
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_parse_ss_endpoint_companion() now decodes the burst multiplier
correctly in order to check that it's <= 3, but still uses the wrong
expression if warning that it's > 3.
Fixes: ff30cbc8da ("usb: Use the USB_SS_MULT() macro to get the ...")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
qset_fill_page_list() do not check for dma mapping errors.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB 3.0 mass storage device is disconnected in transporting
state, storage device driver may handle it as a transport error and
reset the device by invoking usb_reset_and_verify_device()
and following could happen:
in usb_reset_and_verify_device():
udev->bos = NULL;
For U1/U2 enabled devices, driver will disable LPM, and in some
conditions:
from usb_unlocked_disable_lpm()
--> usb_disable_lpm()
--> usb_enable_lpm()
udev->bos->ss_cap->bU1devExitLat;
And it causes 'NULL pointer' and 'kernel panic':
[ 157.976257] Unable to handle kernel NULL pointer dereference
at virtual address 00000010
...
[ 158.026400] PC is at usb_enable_link_state+0x34/0x2e0
[ 158.031442] LR is at usb_enable_lpm+0x98/0xac
...
[ 158.137368] [<ffffffc0006a1cac>] usb_enable_link_state+0x34/0x2e0
[ 158.143451] [<ffffffc0006a1fec>] usb_enable_lpm+0x94/0xac
[ 158.148840] [<ffffffc0006a20e8>] usb_disable_lpm+0xa8/0xb4
...
[ 158.214954] Kernel panic - not syncing: Fatal exception
This commit moves 'udev->bos = NULL' behind usb_unlocked_disable_lpm()
to prevent from NULL pointer access.
Issue can be reproduced by following setup:
1) A SS pen drive behind a SS hub connected to the host.
2) Transporting data between the pen drive and the host.
3) Abruptly disconnect hub and pen drive from host.
4) With a chance it crashes.
Signed-off-by: Hans Yang <hansy@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All ELAN hid devices seem to require the ALWAYS_POLL quirk. Let's use
this quirk for all devices from this vendor, rather than maintaining a
list of all its known product IDs.
Tested-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Adrien Vergé <adrienverge@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch extends the family of SATA-to-USB JMicron adapters that need
FUA to be disabled and applies the same policy for uas driver.
See details in http://unix.stackexchange.com/questions/237204/
Signed-off-by: Dmitry Katsubo <dmitry.katsubo@gmail.com>
Tested-by: Dmitry Katsubo <dmitry.katsubo@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like other buggy models that had their fixes [1], the touchscreen with
id 04f3:21b8 from ELAN Microelectronics needs the device-qualifier
quirk. Otherwise, it fails to respond, blocks the boot for a random
amount of time and pollutes dmesg with:
[ 2887.373196] usb 1-5: new full-speed USB device number 41 using xhci_hcd
[ 2889.502000] usb 1-5: unable to read config index 0 descriptor/start: -71
[ 2889.502005] usb 1-5: can't read configurations, error -71
[ 2889.654571] usb 1-5: new full-speed USB device number 42 using xhci_hcd
[ 2891.783438] usb 1-5: unable to read config index 0 descriptor/start: -71
[ 2891.783443] usb 1-5: can't read configurations, error -71
[1]: See commits c68929f, 876af5d, d749947, a32c99e and dc703ec.
Tested-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some device-id fixes that remove a HID device from cp210x, and
adds support for another Infineon flash-loader device. The flash-loader
device presents itself as a CDC-ACM device even though it is clearly
not, so we need to blacklist it in the cdc-acm driver as well.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=JdcP
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.4-rc3
Here are some device-id fixes that remove a HID device from cp210x, and
adds support for another Infineon flash-loader device. The flash-loader
device presents itself as a CDC-ACM device even though it is clearly
not, so we need to blacklist it in the cdc-acm driver as well.
Signed-off-by: Johan Hovold <johan@kernel.org>
Here's our second round of fixes. Some of the bugs are pretty old like
the one on pxa27x suspend implementation.
The most important part is a randbuild warning fix on MUSB CPPI DMA
engine by Arnd, a couple fixes by Felipe Tonello on f_midi (first one
makes sure we only transmit on enabled ep IN while second plugs a memory
leak) and a NULL pointer dereference fix on renesas usbhs.
Note that we also have a new compatible string being added for the MXS
PHY.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qfZS
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.4-rc3
Here's our second round of fixes. Some of the bugs are pretty old like
the one on pxa27x suspend implementation.
The most important part is a randbuild warning fix on MUSB CPPI DMA
engine by Arnd, a couple fixes by Felipe Tonello on f_midi (first one
makes sure we only transmit on enabled ep IN while second plugs a memory
leak) and a NULL pointer dereference fix on renesas usbhs.
Note that we also have a new compatible string being added for the MXS
PHY.
Because interrupt endpoints usually transmit such
small amounts of data, it seems pointless to prestart
transfers and try to get speed improvements. This
patch also sorts out a problem with CDC ECM function
where its notification endpoint gets stuck in busy
state and we continuously issue Update Transfer
commands.
Fixes: 8a1a9c9e45 ("usb: dwc3: gadget: start transfer on XFER_COMPLETE")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull nouveau and radeon fixes from Dave Airlie:
"Just some nouveau and radeon/amdgpu fixes.
The nouveau fixes look large as the firmware context files are
regenerated, but the actual change is quite small"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: make some dpm errors debug only
drm/nouveau/volt/pwm/gk104: fix an off-by-one resulting in the voltage not being set
drm/nouveau/nvif: allow userspace access to its own client object
drm/nouveau/gr/gf100-: fix oops when calling zbc methods
drm/nouveau/gr/gf117-: assume no PPC if NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK is zero
drm/nouveau/gr/gf117-: read NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK from correct GPC
drm/nouveau/gr/gf100-: split out per-gpc address calculation macro
drm/nouveau/bios: return actual size of the buffer retrieved via _ROM
drm/nouveau/instmem: protect instobj list with a spinlock
drm/nouveau/pci: enable c800 magic for some unknown Samsung laptop
drm/nouveau/pci: enable c800 magic for Clevo P157SM
drm/radeon: make rv770_set_sw_state failures non-fatal
drm/amdgpu: move dependency handling out of atomic section v2
drm/amdgpu: optimize scheduler fence handling
drm/amdgpu: remove vm->mutex
drm/amdgpu: add mutex for ba_va->valids/invalids
drm/amdgpu: adapt vce session create interface changes
drm/amdgpu: vce use multiple cache surface starting from stoney
drm/amdgpu: reset vce trap interrupt flag
Two fixes for the ds1307 alarm and wakeup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6IeZ
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fixes from Alexandre Belloni:
"Two fixes for the ds1307 alarm and wakeup"
* tag 'rtc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: ds1307: fix alarm reading at probe time
rtc: ds1307: fix kernel splat due to wakeup irq handling
Pull MIPS fix from Ralf Baechle:
"Just a fix for empty loops that may be removed by non-antique GCC"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix delay loops which may be removed by GCC.
Pull m68k fixes from Geert Uytterhoeven:
"Summary:
- Add missing initialization of max_pfn, which is needed to make
selftests/vm/mlock2-tests succeed,
- Wire up new mlock2 syscall"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Wire up mlock2
m68knommu: Add missing initialization of max_pfn and {min,max}_low_pfn
m68k/mm: sun3 - Add missing initialization of max_pfn and {min,max}_low_pfn
m68k/mm: m54xx - Add missing initialization of max_pfn
m68k/mm: motorola - Add missing initialization of max_pfn
Pull ARM fixes from Russell King:
"Just two changes this time around:
- wire up the new mlock2 syscall added during the last merge window
- fix a build problem with certain configurations provoked by making
CONFIG_OF user selectable"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8454/1: OF implies OF_FLATTREE
ARM: wire up mlock2 syscall
Pull SCSI target fixes from Nicholas Bellinger:
- fix tcm-user backend driver expired cmd time processing (agrover)
- eliminate kref_put_spinlock_irqsave() for I/O completion (bart)
- fix iscsi login kthread failure case hung task regression (nab)
- fix COMPARE_AND_WRITE completion use-after-free race (nab)
- fix COMPARE_AND_WRITE with SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC non zero
SGL offset data corruption. (Jan + Doug)
- fix >= v4.4-rc1 regression for tcm_qla2xxx enable configfs attribute
(Himanshu + HCH)
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/stat: print full t10_wwn.model buffer
target: fix COMPARE_AND_WRITE non zero SGL offset data corruption
qla2xxx: Fix regression introduced by target configFS changes
kref: Remove kref_put_spinlock_irqsave()
target: Invoke release_cmd() callback without holding a spinlock
target: Fix race for SCF_COMPARE_AND_WRITE_POST checking
iscsi-target: Fix rx_login_comp hang after login failure
iscsi-target: return -ENOMEM instead of -1 in case of failed kmalloc()
target/user: Do not set unused fields in tcmu_ops
target/user: Fix time calc in expired cmd processing
Pull thermal management fixes from Zhang Rui:
"Specifics:
- several fixes and cleanups on Rockchip thermal drivers.
- add the missing support of RK3368 SoCs in Rockchip driver.
- small fixes on of-thermal, power_allocator, rcar driver, IMX, and
QCOM drivers, and also compilation fixes, on thermal.h, when thermal
is not selected"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
imx: thermal: use CPU temperature grade info for thresholds
thermal: fix thermal_zone_bind_cooling_device prototype
Revert "thermal: qcom_spmi: allow compile test"
thermal: rcar_thermal: remove redundant operation
thermal: of-thermal: Reduce log level for message when can't fine thermal zone
thermal: power_allocator: Use temperature reading from tz
thermal: rockchip: Support the RK3368 SoCs in thermal driver
thermal: rockchip: consistently use int for temperatures
thermal: rockchip: Add the sort mode for adc value increment or decrement
thermal: rockchip: improve the conversion function
thermal: rockchip: trivial: fix typo in commit
thermal: rockchip: better to compatible the driver for different SoCs
dt-bindings: rockchip-thermal: Support the RK3368 SoCs compatible
Cut 'n paste error saw it only process sizeof(t10_wwn.vendor) characters.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target_core_sbc's compare_and_write functionality suffers from taking
data at the wrong memory location when writing a CAW request to disk
when a SGL offset is non-zero.
This can happen with loopback and vhost-scsi fabric drivers when
SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC is used to map existing user-space
SGL memory into COMPARE_AND_WRITE READ/WRITE payload buffers.
Given the following sample LIO subtopology,
% targetcli ls /loopback/
o- loopback ................................. [1 Target]
o- naa.6001405ebb8df14a ....... [naa.60014059143ed2b3]
o- luns ................................... [2 LUNs]
o- lun0 ................ [iblock/ram0 (/dev/ram0)]
o- lun1 ................ [iblock/ram1 (/dev/ram1)]
% lsscsi -g
[3:0:1:0] disk LIO-ORG IBLOCK 4.0 /dev/sdc /dev/sg3
[3:0:1:1] disk LIO-ORG IBLOCK 4.0 /dev/sdd /dev/sg4
the following bug can be observed in Linux 4.3 and 4.4~rc1:
% perl -e 'print chr$_ for 0..255,reverse 0..255' >rand
% perl -e 'print "\0" x 512' >zero
% cat rand >/dev/sdd
% sg_compare_and_write -i rand -D zero --lba 0 /dev/sdd
% sg_compare_and_write -i zero -D rand --lba 0 /dev/sdd
Miscompare reported
% hexdump -Cn 512 /dev/sdd
00000000 0f 0e 0d 0c 0b 0a 09 08 07 06 05 04 03 02 01 00
00000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
*
00000200
Rather than writing all-zeroes as instructed with the -D file, it
corrupts the data in the sector by splicing some of the original
bytes in. The page of the first entry of cmd->t_data_sg includes the
CDB, and sg->offset is set to a position past the CDB. I presume that
sg->offset is also the right choice to use for subsequent sglist
members.
Signed-off-by: Jan Engelhardt <jengelh@netitwork.de>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
this patch fixes following regression
# targetcli
[Errno 13] Permission denied: '/sys/kernel/config/target/qla2xxx/21:00:00:0e:1e:08:c7:20/tpgt_1/enable'
Fixes: 2eafd72939 ("target: use per-attribute show and store methods")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The last user is gone. Hence remove this function.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a race + use after free where the first
stage of COMPARE_AND_WRITE in compare_and_write_callback()
is rescheduled after the backend sends the secondary WRITE,
resulting in second stage compare_and_write_post() callback
completing in target_complete_ok_work() before the first
can return.
Because current code depends on checking se_cmd->se_cmd_flags
after return from se_cmd->transport_complete_callback(),
this results in first stage having SCF_COMPARE_AND_WRITE_POST
set, which incorrectly falls through into second stage CAW
processing code, eventually triggering a NULL pointer
dereference due to use after free.
To address this bug, pass in a new *post_ret parameter into
se_cmd->transport_complete_callback(), and depend upon this
value instead of ->se_cmd_flags to determine when to return
or fall through into ->queue_status() code for CAW.
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a case where iscsi_target_do_tx_login_io()
fails sending the last login response PDU, after the RX/TX
threads have already been started.
The case centers around iscsi_target_rx_thread() not invoking
allow_signal(SIGINT) before the send_sig(SIGINT, ...) occurs
from the failure path, resulting in RX thread hanging
indefinately on iscsi_conn->rx_login_comp.
Note this bug is a regression introduced by:
commit e54198657b
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Wed Jul 22 23:14:19 2015 -0700
iscsi-target: Fix iscsit_start_kthreads failure OOPs
To address this bug, complete ->rx_login_complete for good
measure in the failure path, and immediately return from
RX thread context if connection state did not actually reach
full feature phase (TARG_CONN_STATE_LOGGED_IN).
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Smatch complains about returning hard coded error codes, silence this
warning.
drivers/target/iscsi/iscsi_target_parameters.c:211
iscsi_create_default_params() warn: returning -1 instead of -ENOMEM is sloppy
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
TCMU sets TRANSPORT_FLAG_PASSTHROUGH, so INQUIRY commands will not be
emulated by LIO but passed up to userspace. Therefore TCMU should not
set these, just like pscsi doesn't.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Reversed arguments meant that we were doing nothing for cmds whose deadline
had passed.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
On the ARM architecture, individual platforms select CONFIG_USE_OF if they
need it, but all device tree code is keyed off CONFIG_OF. When building
a platform without DT support and manually enabling CONFIG_OF, we now
get a number of build errors, e.g.
arch/arm/kernel/devtree.c: In function 'setup_machine_fdt':
arch/arm/kernel/devtree.c:215:19: error: implicit declaration of function 'early_init_dt_verify' [-Werror=implicit-function-declaration]
We could now try to separate the use case of booting from DT vs. the
case of using the dynamic implementation, but that seems more complicated
than it can gain us.
This simply changes the ARM Kconfig file to always enable OF_RESERVED_MEM
and OF_EARLY_FLATTREE when CONFIG_OF is enabled. These options add a little
extra code when we just want the dynamic OF implementation, but that seems
like a rather obscure case, and this version solves all CONFIG_OF related
randconfig regressions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0166dc11be ("of: make CONFIG_OF user selectable")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
NUMA
Prevent out of bounds access in numa_node override (Mathias Krause)
HiSilicon host bridge driver
Fix deferred probing (Arnd Bergmann)
Synopsys DesignWare host bridge driver
Remove incorrect io_base assignment (Stanimir Varbanov)
Move align_resource function pointer to pci_host_bridge structure (Gabriele Paoloni)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kWE6
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.4-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Here are a few fixes I'd like to have in v4.4: a generic one for sysfs
and three for HiSilicon and DesignWare host controllers.
Summary:
NUMA:
- Prevent out of bounds access in numa_node override (Mathias Krause)
HiSilicon host bridge driver:
- Fix deferred probing (Arnd Bergmann)
Synopsys DesignWare host bridge driver:
- Remove incorrect io_base assignment (Stanimir Varbanov)
- Move align_resource function pointer to pci_host_bridge structure
(Gabriele Paoloni)"
* tag 'pci-v4.4-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
ARM/PCI: Move align_resource function pointer to pci_host_bridge structure
PCI: hisi: Fix deferred probing
PCI: designware: Remove incorrect io_base assignment
PCI: Prevent out of bounds access in numa_node override
Highlights include:
Stable patches:
- Fix a NFSv4 callback identifier leak that was also causing client crashes
- Fix NFSv4 callback decoding issues when incoming requests are truncated
- Don't declare the attribute cache valid when we call nfs_update_inode with
an empty attribute structure.
- Resend LAYOUTGET when there is a race that changes the seqid
Bugfixes:
- Fix a number of issues with the NFSv4.2 CLONE ioctl()
- Properly set NFS v4.2 NFSDBG_FACILITY
- NFSv4 referrals are broken; Cleanup FATTR4_WORD0_FS_LOCATIONS after
decoding success
- Use sliding delay when LAYOUTGET gets NFS4ERR_DELAY
- Ensure that attrcache is revalidated after a SETATTR
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWWPeyAAoJEGcL54qWCgDy9/UQAKNTF09OeHxSqO7oXbM4x0hY
8a8A4ostTshtu4g6OWxeqI4/89A5lOcdHAoM/KOr+2HzssKA6B9lU4+pzcKfFI+U
d9WqKVEC3MZA1N4KR+fS5LhtQU62izGKH+CQ9+tHvvesZu+bIiQgQu/uMzKVh2Al
cKdDu99UxrxNP3PFDCcBtxpBvy27akT+21P8RutG12tqGQkfa1715JIQl9bqgquY
ZruukMsqamp+LbZlnowgvoaBLBVUo19v8zwI34uSfXwNbQS71xmAV52z7HVHaEFt
A8HQzS/MaFtMKpq7HOZYEnHB6h8YaYTK4GmHcCCFXHtjXopvHo8LXA6vYLTNhJ8V
SvLpUJzUWVcGDDQ75x6iX/APPMSq0gxJA4+AZryBer3k2EvKlUoRrP+hgxOIK7HT
2joWoFFKVe8a5NBj4Pd5+x6dpDEnIvlqGdMQNuXFUiPvcA/l3Uc0gnWhauuqvrhy
ePrLRcWoSikLlPWxq39DRzJjQUdyUhBWMcCRWkhNzsT6U6HDSip5j0BkUBXD7nlU
FK9BM2zRHr7kQ5Aax497K9qJNZBWI94y/vFkR/hJg0Z/bVQBF45lGxGgNFbj8Kag
gR/xcYC9plum1IFD7DcnVnJTxrDSftIsLS8bhjmknxC8Pcyur2jegZvoDXiFk1GF
gXERq36Ej/4WyyGrNyWm
=5aPD
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.4-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable patches:
- Fix a NFSv4 callback identifier leak that was also causing client
crashes
- Fix NFSv4 callback decoding issues when incoming requests are
truncated
- Don't declare the attribute cache valid when we call
nfs_update_inode with an empty attribute structure.
- Resend LAYOUTGET when there is a race that changes the seqid
Bugfixes:
- Fix a number of issues with the NFSv4.2 CLONE ioctl()
- Properly set NFS v4.2 NFSDBG_FACILITY
- NFSv4 referrals are broken; Cleanup FATTR4_WORD0_FS_LOCATIONS after
decoding success
- Use sliding delay when LAYOUTGET gets NFS4ERR_DELAY
- Ensure that attrcache is revalidated after a SETATTR"
* tag 'nfs-for-4.4-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs4: resend LAYOUTGET when there is a race that changes the seqid
nfs: if we have no valid attrs, then don't declare the attribute cache valid
nfs: ensure that attrcache is revalidated after a SETATTR
nfs4: limit callback decoding to received bytes
nfs4: start callback_ident at idr 1
nfs: use sliding delay when LAYOUTGET gets NFS4ERR_DELAY
NFS4: Cleanup FATTR4_WORD0_FS_LOCATIONS after decoding success
NFS: Properly set NFS v4.2 NFSDBG_FACILITY
nfs: reduce the amount of ifdefs for v4.2 in nfs4file.c
nfs: use btrfs ioctl defintions for clone
nfs: allow intra-file CLONE
nfs: offer native ioctls even if CONFIG_COMPAT is set
nfs: pass on count for CLONE operations
Pull watchdog fixes from Wim Van Sebroeck:
- a null pointer dereference fix for omap_wdt
- some clock related fixes for pnx4008
- an underflow fix in wdt_set_timeout() for w83977f_wdt
- restart fix for tegra wdt
- Kconfig change to support Freescale Layerscape platforms
- fix for stopping the mtk_wdt watchdog
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: mtk_wdt: Use MODE_KEY when stopping the watchdog
watchdog: Add support for Freescale Layerscape platforms
watchdog: tegra: Stop watchdog first if restarting
watchdog: w83977f_wdt: underflow in wdt_set_timeout()
watchdog: pnx4008: make global wdt_clk static
watchdog: pnx4008: fix warnings caused by enabling unprepared clock
watchdog: omap_wdt: fix null pointer dereference
Pull btrfs fixes from Chris Mason:
"This has Mark Fasheh's patches to fix quota accounting during subvol
deletion, which we've been working on for a while now. The patch is
pretty small but it's a key fix.
Otherwise it's a random assortment"
* 'for-linus-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix balance range usage filters in 4.4-rc
btrfs: qgroup: account shared subtree during snapshot delete
Btrfs: use btrfs_get_fs_root in resolve_indirect_ref
btrfs: qgroup: fix quota disable during rescan
Btrfs: fix race between cleaner kthread and space cache writeout
Btrfs: fix scrub preventing unused block groups from being deleted
Btrfs: fix race between scrub and block group deletion
btrfs: fix rcu warning during device replace
btrfs: Continue replace when set_block_ro failed
btrfs: fix clashing number of the enhanced balance usage filter
Btrfs: fix the number of transaction units needed to remove a block group
Btrfs: use global reserve when deleting unused block group after ENOSPC
Btrfs: tests: checking for NULL instead of IS_ERR()
btrfs: fix signed overflows in btrfs_sync_file
Pull security layer fixes from James Morris:
"A fix for SELinux policy processing (regression introduced by
commit fa1aa143ac4a: "selinux: extended permissions for ioctls"), as
well as a fix for the user-triggerable oops in the Keys code"
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
KEYS: Fix handling of stored error in a negatively instantiated user key
selinux: fix bug in conditional rules handling
There is a small backlog of at91 patches here, the most significant is
the addition of some sama5d2 Xplained nodes that were waiting on an MFD include
file to get merged through another tree. We normally try to sort those out
before the merge window opens, but the maintainer wasn't aware of that here
and I decided to merge the changes this time as an exception.
On OMAP a series of audio changes for dra7 missed the merge window but turned
out to be necessary to fix a boot time imprecise external abort error and to
get audio working.
The other changes are the usual simple changes, here is a list sorted by
platform:
at91:
removal of a useless defconfig option
removal of some legacy DT pieces
use of the proper watchdog compatible string
update of the MAINTAINERS entries for some Atmel drivers
drivers/scpi:
hide get_scpi_ops in module from built-in code
imx:
add missing .irq_set_type for i.MX GPC irq_chip.
fix the wrong spi-num-chipselects settings for Vybrid DSPI devices.
fix a merge error in Vybrid dts regarding to ADC device property
keystone:
fix the optional PDSP firmware loading
fix linking RAM setup for QMs
fix crash with clk_ignore_unused
mediatek:
Enable SCPSYS power domain driver by default
mvebu:
fix QNAP TS219 power-off in dts
fix legacy get_irqnr_and_base for dove and orion5x
omap:
fix l4 related boot time errors for dm81xx
use lockless cldm/pwrdm api in omap4_boot_secondary
remove t410 abort handler to avoid hiding other critical errors
mark cpuidle tracepoints as _rcuidle
fix module alias for omap-ocp2scp
pxa:
palm: Fix typos in PWM lookup table code
renesas:
missing __initconst annotation for r8a7793_boards_compat_dt
rockchip:
disable mmc-tuning on the veyron-minnie board
adding the init state for the over-temperature-protection
zx:
only build power domain code when CONFIG_PM=y
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=auFT
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"There is a small backlog of at91 patches here, the most significant is
the addition of some sama5d2 Xplained nodes that were waiting on an
MFD include file to get merged through another tree.
We normally try to sort those out before the merge window opens, but
the maintainer wasn't aware of that here and I decided to merge the
changes this time as an exception.
On OMAP a series of audio changes for dra7 missed the merge window but
turned out to be necessary to fix a boot time imprecise external abort
error and to get audio working.
The other changes are the usual simple changes, here is a list sorted
by platform:
at91:
removal of a useless defconfig option
removal of some legacy DT pieces
use of the proper watchdog compatible string
update of the MAINTAINERS entries for some Atmel drivers
drivers/scpi:
hide get_scpi_ops in module from built-in code
imx:
add missing .irq_set_type for i.MX GPC irq_chip.
fix the wrong spi-num-chipselects settings for Vybrid DSPI devices.
fix a merge error in Vybrid dts regarding to ADC device property
keystone:
fix the optional PDSP firmware loading
fix linking RAM setup for QMs
fix crash with clk_ignore_unused
mediatek:
Enable SCPSYS power domain driver by default
mvebu:
fix QNAP TS219 power-off in dts
fix legacy get_irqnr_and_base for dove and orion5x
omap:
fix l4 related boot time errors for dm81xx
use lockless cldm/pwrdm api in omap4_boot_secondary
remove t410 abort handler to avoid hiding other critical errors
mark cpuidle tracepoints as _rcuidle
fix module alias for omap-ocp2scp
pxa:
palm: Fix typos in PWM lookup table code
renesas:
missing __initconst annotation for r8a7793_boards_compat_dt
rockchip:
disable mmc-tuning on the veyron-minnie board
adding the init state for the over-temperature-protection
zx:
only build power domain code when CONFIG_PM=y"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
ARM: OMAP4+: SMP: use lockless clkdm/pwrdm api in omap4_boot_secondary
arm: omap2+: add missing HWMOD_NO_IDLEST in 81xx hwmod data
ARM: orion5x: Fix legacy get_irqnr_and_base
ARM: dove: Fix legacy get_irqnr_and_base
soc: Mediatek: Enable SCPSYS power domain driver by default
ARM: dts: vfxxx: Fix dspi[01] spi-num-chipselects.
ARM: dts: keystone: k2l: fix kernel crash when clk_ignore_unused is not in bootargs
soc: ti: knav_qmss_queue: Fix linking RAM setup for queue managers
soc: ti: use request_firmware_direct() as acc firmware is optional
ARM: imx: add platform irq type setting in gpc
ARM: dts: vfxxx: Fix erroneous property in esdhc0 node
ARM: shmobile: r8a7793: proper constness with __initconst
scpi: hide get_scpi_ops in module from built-in code
ARM: zx: only build power domain code when CONFIG_PM=y
ARM: pxa: palm: Fix typos in PWM lookup table code
ARM: dts: Kirkwood: Fix QNAP TS219 power-off
ARM: dts: rockchip: Add OTP gpio pinctrl to rk3288 tsadc node
ARM: dts: rockchip: temporarily remove emmc hs200 speed from rk3288 minnie
MAINTAINERS: Atmel drivers: change NAND and ISI entries
ARM: at91/dt: sama5d2 Xplained: add several devices
...
- Fix a recent regression in the cpufreq core causing it to fail
to clean up sysfs directories properly on cpufreq driver removal
(Viresh Kumar).
- Fix a build problem in the SCPI support code recently added to
the arm_big_little cpufreq driver (Punit Agrawal).
- Fix up the recently added CPPC cpufreq frontend to process the
CPU coordination information provided by the platform firmware
correctly (Ashwin Chaugule).
- Fix the intel_pstate driver to behave as intended when switched
over to the "performance" mode via sysfs if hardware-driven
P-state selection (HWP) is enabled (Alexandra Yates).
- Fix two rounding errors in the intel_pstate driver that sometimes
cause it to use lower P-states than requested (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Blij
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI fixes from Rafael Wysocki:
"These fix one recent regression (cpufreq core), fix up two features
added recently (ACPI CPPC support, SCPI support in the arm_big_little
cpufreq driver) and fix three older bugs in the intel_pstate driver.
Specifics:
- Fix a recent regression in the cpufreq core causing it to fail to
clean up sysfs directories properly on cpufreq driver removal
(Viresh Kumar).
- Fix a build problem in the SCPI support code recently added to the
arm_big_little cpufreq driver (Punit Agrawal).
- Fix up the recently added CPPC cpufreq frontend to process the CPU
coordination information provided by the platform firmware
correctly (Ashwin Chaugule).
- Fix the intel_pstate driver to behave as intended when switched
over to the "performance" mode via sysfs if hardware-driven P-state
selection (HWP) is enabled (Alexandra Yates).
- Fix two rounding errors in the intel_pstate driver that sometimes
cause it to use lower P-states than requested (Prarit Bhargava)"
* tag 'pm+acpi-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
intel_pstate: Fix "performance" mode behavior with HWP enabled
cpufreq: SCPI: Depend on SCPI clk driver
cpufreq: intel_pstate: Fix limits->max_perf rounding error
cpufreq: intel_pstate: Fix limits->max_policy_pct rounding error
cpufreq: Always remove sysfs cpuX/cpufreq link on ->remove_dev()
cpufreq: CPPC: Initialize and check CPUFreq CPU co-ord type correctly
Ben Skeggs wrote:
A couple of regression fixes, some more boards whitelisted for a hw bug
workaround, gr/ucode fixes for hangs a user is seeing.
The changes look larger than they actually are due to the ucode binaries
(*.fucN.h) being regenerated.
* 'linux-4.4' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/volt/pwm/gk104: fix an off-by-one resulting in the voltage not being set
drm/nouveau/nvif: allow userspace access to its own client object
drm/nouveau/gr/gf100-: fix oops when calling zbc methods
drm/nouveau/gr/gf117-: assume no PPC if NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK is zero
drm/nouveau/gr/gf117-: read NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK from correct GPC
drm/nouveau/gr/gf100-: split out per-gpc address calculation macro
drm/nouveau/bios: return actual size of the buffer retrieved via _ROM
drm/nouveau/instmem: protect instobj list with a spinlock
drm/nouveau/pci: enable c800 magic for some unknown Samsung laptop
drm/nouveau/pci: enable c800 magic for Clevo P157SM
Here are no big surprises but just all small fixes, mostly
device-specific quirks for HD-audio and USB-audio:
- Fix for detection of FireWire DICE Loud devices
- Intel Broxton HDMI/DP PCI IDs and relevant quirks
- Noise fixes: Dell XPS13 2015 model, Dell Latitude E6440, Gigabyte
Z170X mobo
- Fix the headphone mixer assignment on HP laptops for PulseAudio
- USB-MIDI fixes for Medeli DD305 and CH345
- Apply fixup for Acer Aspire One Cloudbook 14
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ab9W
-----END PGP SIGNATURE-----
Merge tag 'sound-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are no big surprises but just all small fixes, mostly
device-specific quirks for HD-audio and USB-audio:
- Fix for detection of FireWire DICE Loud devices
- Intel Broxton HDMI/DP PCI IDs and relevant quirks
- Noise fixes: Dell XPS13 2015 model, Dell Latitude E6440, Gigabyte
Z170X mobo
- Fix the headphone mixer assignment on HP laptops for PulseAudio
- USB-MIDI fixes for Medeli DD305 and CH345
- Apply fixup for Acer Aspire One Cloudbook 14"
* tag 'sound-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix noise on Gigabyte Z170X mobo
ALSA: hda - Fix headphone noise after Dell XPS 13 resume back from S3
ALSA: hda - Apply HP headphone fixups more generically
ALSA: hda - Add fixup for Acer Aspire One Cloudbook 14
ALSA: hda - apply SKL display power request/release patch to BXT
ALSA: hda - add PCI IDs for Intel Broxton
ALSA: usb-audio: work around CH345 input SysEx corruption
ALSA: usb-audio: prevent CH345 multiport output SysEx corruption
ALSA: usb-audio: add packet size quirk for the Medeli DD305
ALSA: dice: fix detection of Loud devices
ALSA: hda - Fix noise on Dell Latitude E6440
- Build fix when !CONFIG_UID16 (the patch is touching generic files but
it only affects arm64 builds; submitted by Arnd Bergmann)
- EFI fixes to deal with early_memremap() returning NULL and correctly
mapping run-time regions
- Fix CPUID register extraction of unsigned fields (not to be
sign-extended)
- ASID allocator fix to deal with long-running tasks over multiple
generation roll-overs
- Revert support for marking page ranges as contiguous PTEs (it leads to
TLB conflicts and requires additional non-trivial kernel changes)
- Proper early_alloc() failure check
- Disable KASan for 48-bit VA and 16KB page configuration (the pgd is
larger than the KASan shadow memory)
- Update the fault_info table (original descriptions based on early
engineering spec)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWWJiuAAoJEGvWsS0AyF7xlWIP/3ma+ZSyitIS0FWOld/uo3c1
KbH9i7DrEL9tOzz4AhkKHBA7LOs0NvNkjz2sPLbnVg57H6r2y6Bi1ls5ODUWFy6y
CKI0aaCYhWPyYWDq6H9NfD5Xh6jx0+45dMqKiCy1mvpChEwPfW4aZGceKptNbBrG
v0VG1H5s0U+SjNqKqZ3W/hbwyQ1ZvAXJ022q7/ihPt6s2U0ebjXqc+6S2TcJyWNn
C0bDn40+MK7p8jqRrq80bAjAvC5yDQ7/o7fBsNzsVYhuNTA3HR5CG1jGMJwGcVvA
NJt71vfBq8L4PT2ndt8BxC5G500GdkQk2Nb2i1G9EgakH8Yv5Y2deFTUFDYPTHBg
EfUgORet2iBiCcLY+lLTonjKICsHi4Bn//DsyyEZ7HXAovS0DIH3rQfKubYNlT3p
FR2eskr3cDoQei3L9u0YU1zn+OuWRS7yJdjisjcTAEFaRBKqRXYMoczhVvJPb5xQ
RPtHZNAS0JXH+0Cmdo+nHjSfpEo20nefBvd3Xvs0jvwWKxS6rwexxQWYTKNTbycq
5iTYOGXlequnyTztK5M0AcfAajE+EVT2mAXkD/C727tUdO7yiCh86CNLIREHK8sH
cLnc2iJ12IsJmqV7uRPI5YjNmYau7ZQpfcRfflt1LlL7mx1VmSiyb4JeomGEE/gu
IdJ1iBl2JGguat1DHIXU
=YgtU
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Build fix when !CONFIG_UID16 (the patch is touching generic files but
it only affects arm64 builds; submitted by Arnd Bergmann)
- EFI fixes to deal with early_memremap() returning NULL and correctly
mapping run-time regions
- Fix CPUID register extraction of unsigned fields (not to be
sign-extended)
- ASID allocator fix to deal with long-running tasks over multiple
generation roll-overs
- Revert support for marking page ranges as contiguous PTEs (it leads
to TLB conflicts and requires additional non-trivial kernel changes)
- Proper early_alloc() failure check
- Disable KASan for 48-bit VA and 16KB page configuration (the pgd is
larger than the KASan shadow memory)
- Update the fault_info table (original descriptions based on early
engineering spec)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: efi: fix initcall return values
arm64: efi: deal with NULL return value of early_memremap()
arm64: debug: Treat the BRPs/WRPs as unsigned
arm64: cpufeature: Track unsigned fields
arm64: cpufeature: Add helpers for extracting unsigned values
Revert "arm64: Mark kernel page ranges contiguous"
arm64: mm: keep reserved ASIDs in sync with mm after multiple rollovers
arm64: KASAN depends on !(ARM64_16K_PAGES && ARM64_VA_BITS_48)
arm64: efi: correctly map runtime regions
arm64: mm: fix fault_info table xFSC decoding
arm64: fix building without CONFIG_UID16
arm64: early_alloc: Fix check for allocation failure
Alan Stern
Mathias Nyman
Greg Kroah-Hartman
Aaro Koskinen
Mian Yousaf Kaukab
Tony Lindgren
LABBE Corentin
Alexandre Belloni
Don Zickus
Chunfeng Yun
Mika Westerberg
Ben Hutchings
Alexey Khoroshilov
Hans Yang
Adrien Vergé
Dmitry Katsubo
Felipe Balbi
Linus Torvalds
David Disseldorp
Jan Engelhardt
Himanshu Madhani
Bart Van Assche
Nicholas Bellinger
Luis de Bethencourt
Andy Grover
Arnd Bergmann
Dave Airlie