Commit Graph

3795 Commits

Author SHA1 Message Date
Mark Brown 4d02976372
Merge remote-tracking branches 'spi/fix/armada', 'spi/fix/atmel', 'spi/fix/doc', 'spi/fix/imx', 'spi/fix/rspi', 'spi/fix/sun4i' and 'spi/fix/xilinx' into spi-linus 2017-12-19 11:07:00 +00:00
Radu Pirea 66e900a3d2
spi: atmel: fixed spin_lock usage inside atmel_spi_remove
The only part of atmel_spi_remove which needs to be atomic is hardware
reset.

atmel_spi_stop_dma calls dma_terminate_all and this needs interrupts
enabled.
atmel_spi_release_dma calls dma_release_channel and dma_release_channel
locks a mutex inside of spin_lock.

So the call of these functions can't be inside a spin_lock.

Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-12-19 09:35:35 +00:00
Takuo Koguchi c810daba0a
spi: sun4i: disable clocks in the remove function
mclk and hclk need to be disabled. Since pm_runtime_disable does
not disable the clocks, use pm_runtime_force_suspend instead.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Takuo Koguchi <takuo.koguchi.sw@hitachi.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-12-07 11:59:15 +00:00
Geert Uytterhoeven b458a3490e
spi: rspi: Do not set SPCR_SPE in qspi_set_config_register()
The R-Car Gen2 Hardware User Manual Rev. 2.00 states:

    If the master/slave mode select bit (MSTR) is modified while the SPI
    function enable bit (SPE) is set to 1 (that is, this module is
    enabled), the subsequent operation cannot be guaranteed.

Hence do not set SPCR_SPE when setting SPCR_MSTR, just like the
.set_config_register() implementations for other RSPI variants do.

Note that when booted from QSPI, the boot loader will have set SPCR_MSTR
already, hence usually the bit is never modified by the Linux driver.

Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-12-07 11:55:38 +00:00
Maxime Chevallier 251c201bf4
spi: a3700: Fix clk prescaling for coefficient over 15
The Armada 3700 SPI controller has 2 ranges of prescaler coefficients.
One ranging from 0 to 15 by steps of 1, and one ranging from 0 to 30 by
steps of 2.

This commit fixes the prescaler coefficients that are over 15 so that it
uses the correct range of values. The prescaling coefficient is rounded
to the upper value if it is odd.

This was tested on Espressobin with spidev and a locigal analyser.

Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
2017-11-27 15:23:30 +00:00
Ricardo Ribalda 5a1314fa69
spi: xilinx: Detect stall with Unknown commands
When the core is configured in C_SPI_MODE > 0, it integrates a
lookup table that automatically configures the core in dual or quad mode
based on the command (first byte on the tx fifo).

Unfortunately, that list mode_?_memoy_*.mif does not contain all the
supported commands by the flash.

Since 4.14 spi-nor automatically tries to probe the flash using SFDP
(command 0x5a), and that command is not part of the list_mode table.

Whit the right combination of C_SPI_MODE and C_SPI_MEMORY this leads
into a stall that can only be recovered with a soft rest.

This patch detects this kind of stall and returns -EIO to the caller on
those commands. spi-nor can handle this error properly:

m25p80 spi0.0: Detected stall. Check C_SPI_MODE and C_SPI_MEMORY. 0x21 0x2404
m25p80 spi0.0: SPI transfer failed: -5
spi_master spi0: failed to transfer one message from queue
m25p80 spi0.0: s25sl064p (8192 Kbytes)

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
2017-11-24 13:09:22 +00:00
Mark Brown abbdb5ce31
Merge remote-tracking branches 'spi/topic/sh-msiof', 'spi/topic/slave', 'spi/topic/spreadtrum' and 'spi/topic/tegra114' into spi-next 2017-11-10 21:33:51 +00:00
Mark Brown 6e69547250
Merge remote-tracking branches 'spi/topic/imx', 'spi/topic/mxs', 'spi/topic/orion', 'spi/topic/rspi' and 'spi/topic/s3c64xx' into spi-next 2017-11-10 21:33:47 +00:00
Mark Brown 704c14554b
Merge remote-tracking branches 'spi/topic/armada', 'spi/topic/axi', 'spi/topic/davinci' and 'spi/topic/fsl-dspi' into spi-next 2017-11-10 21:33:44 +00:00
Mark Brown b5f9208dea
Merge remote-tracking branch 'spi/topic/core' into spi-next 2017-11-10 21:33:43 +00:00
Mark Brown 130555cf3b
Merge remote-tracking branches 'spi/fix/idr' and 'spi/fix/sh-msiof' into spi-linus 2017-11-10 21:33:40 +00:00
Trent Piepho ffd4db9e10
spi: imx: Don't require platform data chipselect array
If the array is not present, assume all chip selects are native.  This
is the standard behavior for SPI masters configured via the device
tree and the behavior of this driver as well when it is configured via
device tree.

This reduces platform data vs DT differences and allows most of the
platform data based boards to remove their chip select arrays.

CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Mark Brown <broonie@kernel.org>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-11-10 21:28:11 +00:00
Trent Piepho 4e21791e74
spi: imx: Fix failure path leak on GPIO request error
If the code that requests any chip select GPIOs fails, the cleanup of
spi_bitbang_start() by calling spi_bitbang_stop() is not done.  Add this
to the failure path.

Note that spi_bitbang_start() has to be called before requesting GPIOs
because the GPIO data in the spi master is populated when the master is
registed, and that doesn't happen until spi_bitbang_start() is called.

CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Mark Brown <broonie@kernel.org>
CC: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-11-10 21:28:10 +00:00
Trent Piepho 881a0b993e
spi: imx: GPIO based chip selects should not be required
The driver will fail to load if no gpio chip selects are specified,
this patch changes this so that it no longer fails.

It's possible to use all native chip selects, in which case there is
no reason to have a gpio chip select array.  This is what happens if
the *optional* device tree property "cs-gpios" is omitted.

The spi core already checks for the absence of gpio chip selects in
the master and assigns any slaves the gpio_cs value of -ENOENT.

Also have the driver respect the standard SPI device tree property "num-cs"
to allow setting the number of chip selects without using cs-gpios.

CC: Mark Brown <broonie@kernel.org>
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-11-10 21:28:09 +00:00
Colin Ian King 6ae6678344
spi: sh-msiof: remove redundant pointer dev
The pointer dev is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:

drivers/spi/spi-sh-msiof.c:1198:2: warning: Value stored to 'dev'
is never read

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-11-03 17:21:34 +00:00
Colin Ian King 4132b8b910
spi: s3c64xx: remove redundant pointer sci
The pointer sci is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:

drivers/spi/spi-s3c64xx.c:791:2: warning: Value stored to 'sci' is
never read

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-11-03 17:21:10 +00:00
Angelo Dureghello ec7ed7708e
spi: spi-fsl-dspi: enabling Coldfire mcf5441x dspi
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-11-03 12:53:16 +01:00
Lucas Stach 42bdd7061a
spi: fix IDR collision on systems with both fixed and dynamic SPI bus numbers
On systems where some controllers get a dynamic ID assigned and some have
a fixed number from DT, the current implemention might run into an IDR
collision if the dynamic controllers gets probed first and get an IDR number,
which is later requested by the controller with the fixed numbering. When
this happens the fixed controller will fail to register with the SPI core.

Fix this by skipping all known alias numbers when assigning the dynamic IDs.

Fixes: 9b61e30221 (spi: Pick spi bus number from Linux idr or spi alias)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-11-03 12:08:18 +01:00
Linus Torvalds ead751507d License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
 makes it harder for compliance tools to determine the correct license.
 
 By default all files without license information are under the default
 license of the kernel, which is GPL version 2.
 
 Update the files which contain no license information with the 'GPL-2.0'
 SPDX license identifier.  The SPDX identifier is a legally binding
 shorthand, which can be used instead of the full boiler plate text.
 
 This patch is based on work done by Thomas Gleixner and Kate Stewart and
 Philippe Ombredanne.
 
 How this work was done:
 
 Patches were generated and checked against linux-4.14-rc6 for a subset of
 the use cases:
  - file had no licensing information it it.
  - file was a */uapi/* one with no licensing information in it,
  - file was a */uapi/* one with existing licensing information,
 
 Further patches will be generated in subsequent months to fix up cases
 where non-standard license headers were used, and references to license
 had to be inferred by heuristics based on keywords.
 
 The analysis to determine which SPDX License Identifier to be applied to
 a file was done in a spreadsheet of side by side results from of the
 output of two independent scanners (ScanCode & Windriver) producing SPDX
 tag:value files created by Philippe Ombredanne.  Philippe prepared the
 base worksheet, and did an initial spot review of a few 1000 files.
 
 The 4.13 kernel was the starting point of the analysis with 60,537 files
 assessed.  Kate Stewart did a file by file comparison of the scanner
 results in the spreadsheet to determine which SPDX license identifier(s)
 to be applied to the file. She confirmed any determination that was not
 immediately clear with lawyers working with the Linux Foundation.
 
 Criteria used to select files for SPDX license identifier tagging was:
  - Files considered eligible had to be source code files.
  - Make and config files were included as candidates if they contained >5
    lines of source
  - File already had some variant of a license header in it (even if <5
    lines).
 
 All documentation files were explicitly excluded.
 
 The following heuristics were used to determine which SPDX license
 identifiers to apply.
 
  - when both scanners couldn't find any license traces, file was
    considered to have no license information in it, and the top level
    COPYING file license applied.
 
    For non */uapi/* files that summary was:
 
    SPDX license identifier                            # files
    ---------------------------------------------------|-------
    GPL-2.0                                              11139
 
    and resulted in the first patch in this series.
 
    If that file was a */uapi/* path one, it was "GPL-2.0 WITH
    Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:
 
    SPDX license identifier                            # files
    ---------------------------------------------------|-------
    GPL-2.0 WITH Linux-syscall-note                        930
 
    and resulted in the second patch in this series.
 
  - if a file had some form of licensing information in it, and was one
    of the */uapi/* ones, it was denoted with the Linux-syscall-note if
    any GPL family license was found in the file or had no licensing in
    it (per prior point).  Results summary:
 
    SPDX license identifier                            # files
    ---------------------------------------------------|------
    GPL-2.0 WITH Linux-syscall-note                       270
    GPL-2.0+ WITH Linux-syscall-note                      169
    ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
    ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
    LGPL-2.1+ WITH Linux-syscall-note                      15
    GPL-1.0+ WITH Linux-syscall-note                       14
    ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
    LGPL-2.0+ WITH Linux-syscall-note                       4
    LGPL-2.1 WITH Linux-syscall-note                        3
    ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
    ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1
 
    and that resulted in the third patch in this series.
 
  - when the two scanners agreed on the detected license(s), that became
    the concluded license(s).
 
  - when there was disagreement between the two scanners (one detected a
    license but the other didn't, or they both detected different
    licenses) a manual inspection of the file occurred.
 
  - In most cases a manual inspection of the information in the file
    resulted in a clear resolution of the license that should apply (and
    which scanner probably needed to revisit its heuristics).
 
  - When it was not immediately clear, the license identifier was
    confirmed with lawyers working with the Linux Foundation.
 
  - If there was any question as to the appropriate license identifier,
    the file was flagged for further research and to be revisited later
    in time.
 
 In total, over 70 hours of logged manual review was done on the
 spreadsheet to determine the SPDX license identifiers to apply to the
 source files by Kate, Philippe, Thomas and, in some cases, confirmation
 by lawyers working with the Linux Foundation.
 
 Kate also obtained a third independent scan of the 4.13 code base from
 FOSSology, and compared selected files where the other two scanners
 disagreed against that SPDX file, to see if there was new insights.  The
 Windriver scanner is based on an older version of FOSSology in part, so
 they are related.
 
 Thomas did random spot checks in about 500 files from the spreadsheets
 for the uapi headers and agreed with SPDX license identifier in the
 files he inspected. For the non-uapi files Thomas did random spot checks
 in about 15000 files.
 
 In initial set of patches against 4.14-rc6, 3 files were found to have
 copy/paste license identifier errors, and have been fixed to reflect the
 correct identifier.
 
 Additionally Philippe spent 10 hours this week doing a detailed manual
 inspection and review of the 12,461 patched files from the initial patch
 version early this week with:
  - a full scancode scan run, collecting the matched texts, detected
    license ids and scores
  - reviewing anything where there was a license detected (about 500+
    files) to ensure that the applied SPDX license was correct
  - reviewing anything where there was no detection but the patch license
    was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
    SPDX license was correct
 
 This produced a worksheet with 20 files needing minor correction.  This
 worksheet was then exported into 3 different .csv files for the
 different types of files to be modified.
 
 These .csv files were then reviewed by Greg.  Thomas wrote a script to
 parse the csv files and add the proper SPDX tag to the file, in the
 format that the file expected.  This script was further refined by Greg
 based on the output to detect more types of files automatically and to
 distinguish between header and source .c files (which need different
 comment types.)  Finally Greg ran the script using the .csv files to
 generate the patches.
 
 Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
 Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
 Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
 6dVh26uchcEQLN/XqUDt
 =x306
 -----END PGP SIGNATURE-----

Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull initial SPDX identifiers from Greg KH:
 "License cleanup: add SPDX license identifiers to some files

  Many source files in the tree are missing licensing information, which
  makes it harder for compliance tools to determine the correct license.

  By default all files without license information are under the default
  license of the kernel, which is GPL version 2.

  Update the files which contain no license information with the
  'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
  binding shorthand, which can be used instead of the full boiler plate
  text.

  This patch is based on work done by Thomas Gleixner and Kate Stewart
  and Philippe Ombredanne.

  How this work was done:

  Patches were generated and checked against linux-4.14-rc6 for a subset
  of the use cases:

   - file had no licensing information it it.

   - file was a */uapi/* one with no licensing information in it,

   - file was a */uapi/* one with existing licensing information,

  Further patches will be generated in subsequent months to fix up cases
  where non-standard license headers were used, and references to
  license had to be inferred by heuristics based on keywords.

  The analysis to determine which SPDX License Identifier to be applied
  to a file was done in a spreadsheet of side by side results from of
  the output of two independent scanners (ScanCode & Windriver)
  producing SPDX tag:value files created by Philippe Ombredanne.
  Philippe prepared the base worksheet, and did an initial spot review
  of a few 1000 files.

  The 4.13 kernel was the starting point of the analysis with 60,537
  files assessed. Kate Stewart did a file by file comparison of the
  scanner results in the spreadsheet to determine which SPDX license
  identifier(s) to be applied to the file. She confirmed any
  determination that was not immediately clear with lawyers working with
  the Linux Foundation.

  Criteria used to select files for SPDX license identifier tagging was:

   - Files considered eligible had to be source code files.

   - Make and config files were included as candidates if they contained
     >5 lines of source

   - File already had some variant of a license header in it (even if <5
     lines).

  All documentation files were explicitly excluded.

  The following heuristics were used to determine which SPDX license
  identifiers to apply.

   - when both scanners couldn't find any license traces, file was
     considered to have no license information in it, and the top level
     COPYING file license applied.

     For non */uapi/* files that summary was:

       SPDX license identifier                            # files
       ---------------------------------------------------|-------
       GPL-2.0                                              11139

     and resulted in the first patch in this series.

     If that file was a */uapi/* path one, it was "GPL-2.0 WITH
     Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
     was:

       SPDX license identifier                            # files
       ---------------------------------------------------|-------
       GPL-2.0 WITH Linux-syscall-note                        930

     and resulted in the second patch in this series.

   - if a file had some form of licensing information in it, and was one
     of the */uapi/* ones, it was denoted with the Linux-syscall-note if
     any GPL family license was found in the file or had no licensing in
     it (per prior point). Results summary:

       SPDX license identifier                            # files
       ---------------------------------------------------|------
       GPL-2.0 WITH Linux-syscall-note                       270
       GPL-2.0+ WITH Linux-syscall-note                      169
       ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
       ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
       LGPL-2.1+ WITH Linux-syscall-note                      15
       GPL-1.0+ WITH Linux-syscall-note                       14
       ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
       LGPL-2.0+ WITH Linux-syscall-note                       4
       LGPL-2.1 WITH Linux-syscall-note                        3
       ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
       ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

     and that resulted in the third patch in this series.

   - when the two scanners agreed on the detected license(s), that
     became the concluded license(s).

   - when there was disagreement between the two scanners (one detected
     a license but the other didn't, or they both detected different
     licenses) a manual inspection of the file occurred.

   - In most cases a manual inspection of the information in the file
     resulted in a clear resolution of the license that should apply
     (and which scanner probably needed to revisit its heuristics).

   - When it was not immediately clear, the license identifier was
     confirmed with lawyers working with the Linux Foundation.

   - If there was any question as to the appropriate license identifier,
     the file was flagged for further research and to be revisited later
     in time.

  In total, over 70 hours of logged manual review was done on the
  spreadsheet to determine the SPDX license identifiers to apply to the
  source files by Kate, Philippe, Thomas and, in some cases,
  confirmation by lawyers working with the Linux Foundation.

  Kate also obtained a third independent scan of the 4.13 code base from
  FOSSology, and compared selected files where the other two scanners
  disagreed against that SPDX file, to see if there was new insights.
  The Windriver scanner is based on an older version of FOSSology in
  part, so they are related.

  Thomas did random spot checks in about 500 files from the spreadsheets
  for the uapi headers and agreed with SPDX license identifier in the
  files he inspected. For the non-uapi files Thomas did random spot
  checks in about 15000 files.

  In initial set of patches against 4.14-rc6, 3 files were found to have
  copy/paste license identifier errors, and have been fixed to reflect
  the correct identifier.

  Additionally Philippe spent 10 hours this week doing a detailed manual
  inspection and review of the 12,461 patched files from the initial
  patch version early this week with:

   - a full scancode scan run, collecting the matched texts, detected
     license ids and scores

   - reviewing anything where there was a license detected (about 500+
     files) to ensure that the applied SPDX license was correct

   - reviewing anything where there was no detection but the patch
     license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
     applied SPDX license was correct

  This produced a worksheet with 20 files needing minor correction. This
  worksheet was then exported into 3 different .csv files for the
  different types of files to be modified.

  These .csv files were then reviewed by Greg. Thomas wrote a script to
  parse the csv files and add the proper SPDX tag to the file, in the
  format that the file expected. This script was further refined by Greg
  based on the output to detect more types of files automatically and to
  distinguish between header and source .c files (which need different
  comment types.) Finally Greg ran the script using the .csv files to
  generate the patches.

  Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
  Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
  Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  License cleanup: add SPDX license identifier to uapi header files with a license
  License cleanup: add SPDX license identifier to uapi header files with no license
  License cleanup: add SPDX GPL-2.0 license identifier to files with no license
2017-11-02 10:04:46 -07:00
Colin Ian King f747c3104e
spi: orion: remove redundant assignment of status to zero
The assignment of status to zero is never read, status is either
updated in the next iteration of the of the loop or several
lines after the end of the loop.  Remove it, cleans up clang warning:

drivers/spi/spi-orion.c:674:4: warning: Value stored to 'status'
is never read

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-11-02 13:03:53 +00:00
Hiromitsu Yamasaki 36735783fd
spi: sh-msiof: Fix DMA transfer size check
DMA supports 32-bit words only,
even if BITLEN1 of SITMDR2 register is 16bit.

Fixes: b0d0ce8b6b ("spi: sh-msiof: Add DMA support")
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-11-02 11:25:44 +00:00
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Trent Piepho 974488e4ce
spi: imx: Fix failure path leak on GPIO request error
If the code that requests any chip select GPIOs fails, the cleanup of
spi_bitbang_start() by calling spi_bitbang_stop() is not done.

Fix this by moving spi_bitbang_start() to after the code that requets
GPIOs.  The GPIOs are dev managed and don't need explicit cleanup.
Since spi_bitbang_start() is now the last operation, it doesn't need
to be cleaned up in the failure path.

CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Mark Brown <broonie@kernel.org>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-10-31 11:20:23 +00:00
Johan Hovold 4d5e0689dc
spi: spi-axi: fix potential use-after-free after deregistration
Take an extra reference to the controller before deregistering it to
prevent use-after-free in the interrupt handler in case an interrupt
fires before the line is disabled.

Fixes: b1353d1c1d ("spi: Add Analog Devices AXI SPI Engine controller support")
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-10-31 11:15:10 +00:00
Johan Hovold 68b892f1fd
spi: document odd controller reference handling
Document the fact that a reference to the controller is dropped as part
of deregistration.

This is an odd pattern as the reference is typically taken in
__spi_alloc_controller() rather than spi_register_controller(). Most
controller drivers gets it right these days and notably the
device-managed interface relies on this behaviour.

Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-10-31 11:09:43 +00:00
Johan Hovold 67f7b2781f
spi: fix use-after-free at controller deregistration
The controller is typically freed as part of device_unregister() so
store the bus id before deregistration to avoid use-after-free when the
id is later released.

Fixes: 9b61e30221 ("spi: Pick spi bus number from Linux idr or spi alias")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable <stable@vger.kernel.org>
2017-10-31 11:09:23 +00:00
Mark Brown 7555aa766b Merge remote-tracking branches 'spi/fix/armada', 'spi/fix/idr', 'spi/fix/qspi', 'spi/fix/stm32' and 'spi/fix/uapi' into spi-linus 2017-10-25 14:06:34 +02:00
Baolin Wang 54e2fc28d9 spi: sprd: Fix the possible negative value of BIT()
When enabling the ADI hardware channels, if the channel id is 31,
then we will get one negative value -1 for BIT() macro, which will
write incorrect value to register.

Fixes: 7e2903cb91 ("spi: Add ADI driver for Spreadtrum platform")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-10-25 14:00:03 +02:00
Lucas Stach 226584aedd spi: fix IDR collision on systems with both fixed and dynamic SPI bus numbers
On systems where some controllers get a dynamic ID assigned and some have
a fixed number from DT, the current implemention might run into an IDR
collision if the dynamic controllers gets probed first and get an IDR number,
which is later requested by the controller with the fixed numbering. When
this happens the fixed controller will fail to register with the SPI core.

Fix this by skipping all known alias numbers when assigning the dynamic IDs.

Fixes: 9b61e30221 (spi: Pick spi bus number from Linux idr or spi alias)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-10-16 21:02:54 +01:00
Wu Fengguang 8955b26d22 spi: sprd-adi: fix platform_no_drv_owner.cocci warnings
drivers/spi/spi-sprd-adi.c:409:3-8: No need to set .owner here. The core will do it.

 Remove .owner field if calls are used which set it automatically

Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci

Fixes: 7e2903cb91 ("spi: Add ADI driver for Spreadtrum platform")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-10-13 22:15:50 +01:00
Florian Fainelli c0368e4db4 spi: bcm-qspi: Fix use after free in bcm_qspi_probe() in error path
There was an inversion in how the error path in bcm_qspi_probe() is done
which would make us trip over a KASAN use-after-free report. Turns out
that qspi->dev_ids does not get allocated until later in the probe
process. Fix this by introducing a new lable: qspi_resource_err which
takes care of cleaning up the SPI master instance.

Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
2017-10-12 09:26:23 +01:00
Maxime Chevallier dd7aa8d4b5 spi: a3700: Change SPI mode before asserting chip-select
The spi device mode should be configured in the controller before the
chip-select is asserted, so that a clock polarity configuration change
is not interpreted as a clock tick by the device.

This patch moves the mode setting to the 'prepare_message' function
instead of the 'transfer_one' function.

By doing so, this patch also removes redundant code in
a3700_spi_clock_set.

This was tested on EspressoBin board, with spidev.

Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-10-10 10:17:06 +01:00
Maxime Chevallier 5a866ec001 spi: a3700: Return correct value on timeout detection
When waiting for transfer completion, a3700_spi_wait_completion
returns a boolean indicating if a timeout occurred.

The function was returning 'true' everytime, failing to detect any
timeout.

This patch makes it return 'false' when a timeout is reached.

Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
2017-10-10 10:14:32 +01:00
Ralf Ramsauer 979a9afe39 spi: tegra114: correct register name in definition
According to "Tegra K1 Processor Technical Reference Manual" (p. 2448),
bit 20 of SPI_COMMAND1 is called CS_SW_VAL and not CS_SS_VAL.

Signed-off-by: Ralf Ramsauer <ralf.ramsauer@oth-regensburg.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-10-09 10:16:38 +01:00
Arnd Bergmann e83f374247 spi: spreadtrum adi: add hwspinlock dependency
With CONFIG_HWSPINLOCK=m, the new driver fails to link as a built-in driver:

drivers/spi/spi-sprd-adi.o: In function `sprd_adi_remove':
spi-sprd-adi.c:(.text+0x18): undefined reference to `hwspin_lock_free'
drivers/spi/spi-sprd-adi.o: In function `sprd_adi_probe':
spi-sprd-adi.c:(.text+0xfc): undefined reference to `of_hwspin_lock_get_id'
spi-sprd-adi.c:(.text+0x108): undefined reference to `hwspin_lock_request_specific'
spi-sprd-adi.c:(.text+0x268): undefined reference to `hwspin_lock_free'

This adds a hard Kconfig dependency on HWSPINLOCK for the !COMPILE_TEST
case, and allows compile-testing with HWSPINLOCK completely disabled,
which will then rely on the existing stub API.

Fixes: 7e2903cb91 ("spi: Add ADI driver for Spreadtrum platform")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-10-05 21:57:16 +01:00
Geert Uytterhoeven ecb1596aa2 spi: sh-msiof: Use of_device_get_match_data() helper
Use the of_device_get_match_data() helper instead of open coding.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-10-04 15:48:20 +01:00
Geert Uytterhoeven 219a7bc577 spi: rspi: Use of_device_get_match_data() helper
Use the of_device_get_match_data() helper instead of open coding.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-10-04 15:47:38 +01:00
Uwe Kleine-König b7969caf41 spi: mxs: implement runtime pm
This is a straight forward addition of runtime and system sleep pm operations
that handle clk and pinctrl (for runtime pm) and spi_master_{suspend,resume}
(for system sleep).

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-09-27 10:02:57 -07:00
Fabrizio Castro bdacfc7b62 spi: sh-msiof: Add compatible strings for r8a774[35]
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-09-25 17:13:34 +01:00
Dan Carpenter b0d6e097b9 spi: sprd-adi: silence an uninitialized variable warning
If of_get_property() fails then "size" is uninitialized and it leads to
a static checker warning:

    drivers/spi/spi-sprd-adi.c:288 sprd_adi_hw_init()
    error: uninitialized symbol 'size'.

We can silence the warning by re-arranging the order of these checks.
It obviously doesn't affect runtime at all.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-09-25 17:09:44 +01:00
Dan Carpenter 04063a011f spi: sprd-adi: checking for NULL instead of IS_ERR()
devm_ioremap_resource() returns error pointers, it never returns NULL.

Fixes: 7e2903cb91 ("spi: Add ADI driver for Spreadtrum platform")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-09-25 17:08:20 +01:00
Fabio Estevam da39471232 spi: Kconfig: Remove old comments now that SPI slave is supported
Since commit 6c364062bf ("spi: core: Add support for registering SPI
slave controllers") SPI slave is also supported, so remove the old
comments that say SPI slave is unsupported.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-09-20 11:46:56 +01:00
jiada wang 71abd29057 spi: imx: Add support for SPI Slave mode
Previously i.MX SPI controller only works in Master mode.
This patch adds support to i.MX51, i.MX53 and i.MX6 ECSPI
controller to work also in Slave mode.

Currently SPI Slave mode support patch has the following limitations:
1. The stale data in RXFIFO will be dropped when the Slave does any new
   transfer.
2. One transfer can be finished only after all transfer->len data been
   transferred to master device
3. Slave device only accepts transfer->len data. Any data longer than this
   from master device will be dropped. Any data shorter than this from
   master will cause SPI to stuck due to mentioned HW limitation 2.
4. Only PIO transfer is supported in Slave mode.
5. Dynamic burst size adjust isn't supported in Slave mode.

Following HW limitation applies:
1.  ECSPI has a HW issue when works in Slave mode, after 64
    words written to TXFIFO, even TXFIFO becomes empty,
    ECSPI_TXDATA keeps shift out the last word data,
    so we have to disable ECSPI when in slave mode after the
    transfer completes
2.  Due to Freescale errata ERR003775 "eCSPI: Burst completion by Chip
    Select (SS) signal in Slave mode is not functional" burst size must
    be set exactly to the size of the transfer. This limit SPI transaction
    with maximum 2^12 bits. This errata affects i.MX53 and i.MX6 ECSPI
    controllers.

Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-09-19 16:01:43 +01:00
Baolin Wang 7e2903cb91 spi: Add ADI driver for Spreadtrum platform
This patch adds ADI driver based on SPI framework for
Spreadtrum SC9860 platform.

Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-09-19 12:53:29 +01:00
Christos Gkekas 8b5d729a3a spi: stm32: Fix logical error in stm32_spi_prepare_mbr()
stm32_spi_prepare_mbr() is returning an error value when div is less
than SPI_MBR_DIV_MIN *and* greater than SPI_MBR_DIV_MAX, which always
evaluates to false. This should change to use *or*.

Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-09-13 09:42:27 -07:00
Zachary Zhang 6fd6fd68c9 spi: armada-3700: Fix padding when sending not 4-byte aligned data
In 4-byte transfer mode, extra padding/dummy bytes '0xff' would be
sent in write operation if TX data is not 4-byte aligned since the
SPI data register is always shifted out as whole 4 bytes.

Fix this by using the header count feature that allows to transfer 0 to
4 bytes. Use it to actually send the first 1 to 3 bytes of data before
the rest of the buffer that will hence be 4-byte aligned.

Signed-off-by: Zachary Zhang <zhangzg@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-09-13 09:37:49 -07:00
Miquel Raynal 747e1f6047 spi: armada-3700: Fix failing commands with quad-SPI
A3700 SPI controller datasheet states that only the first line (IO0) is
used to receive and send instructions, addresses and dummy bytes,
unless for addresses during an RX operation in a quad SPI configuration
(see p.821 of the Armada-3720-DB datasheet). Otherwise, some commands
such as SPI NOR commands like READ_FROM_CACHE_DUAL_IO(0xeb) and
READ_FROM_CACHE_DUAL_IO(0xbb) will fail because these commands must send
address bytes through the four pins. Data transfer always use the four
bytes with this setup.

Thus, in quad SPI configuration, the A3700_SPI_ADDR_PIN bit must be set
only in this case to inform the controller that it must use the number
of pins indicated in the {A3700_SPI_DATA_PIN1,A3700_SPI_DATA_PIN0} field
during the address cycles of an RX operation.

Suggested-by: Ken Ma <make@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
2017-09-13 09:37:26 -07:00
Linus Torvalds 53ac64aac9 ACPI updates for v4.14-rc1
- Update the ACPICA code in the kernel to upstream revision 20170728
    including:
    * Alias operator handling update (Bob Moore).
    * Deferred resolution of reference package elements (Bob Moore).
    * Support for the _DMA method in walk resources (Bob Moore).
    * Tables handling update and support for deferred table
      verification (Lv Zheng).
    * Update of SMMU models for IORT (Robin Murphy).
    * Compiler and disassembler updates (Alex James, Erik Schmauss,
      Ganapatrao Kulkarni, James Morse).
    * Tools updates (Erik Schmauss, Lv Zheng).
    * Assorted minor fixes and cleanups (Bob Moore, Kees Cook,
      Lv Zheng, Shao Ming).
 
  - Rework the initialization of non-wakeup GPEs with method handlers
    in order to address a boot crash on some systems with Thunderbolt
    devices connected at boot time where we miss an early hotplug
    event due to a delay in GPE enabling (Rafael Wysocki).
 
  - Rework the handling of PCI bridges when setting up ACPI-based
    device wakeup in order to avoid disabling wakeup for bridges
    prematurely (Rafael Wysocki).
 
  - Consolidate Apple DMI checks throughout the tree, add support for
    Apple device properties to the device properties framework and
    use these properties for the handling of I2C and SPI devices on
    Apple systems (Lukas Wunner).
 
  - Add support for _DMA to the ACPI-based device properties lookup
    code and make it possible to use the information from there to
    configure DMA regions on ARM64 systems (Lorenzo Pieralisi).
 
  - Fix several issues in the APEI code, add support for exporting
    the BERT error region over sysfs and update APEI MAINTAINERS
    entry with reviewers information (Borislav Petkov, Dongjiu Geng,
    Loc Ho, Punit Agrawal, Tony Luck, Yazen Ghannam).
 
  - Fix a potential initialization ordering issue in the ACPI EC
    driver and clean it up somewhat (Lv Zheng).
 
  - Update the ACPI SPCR driver to extend the existing XGENE 8250
    workaround in it to a new platform (m400) and to work around
    an Xgene UART clock issue (Graeme Gregory).
 
  - Add a new utility function to the ACPI core to support using
    ACPI OEM ID / OEM Table ID / Revision for system identification
    in blacklisting or similar and switch over the existing code
    already using this information to this new interface (Toshi Kani).
 
  - Fix an xpower PMIC issue related to GPADC reads that always return
    0 without extra pin manipulations (Hans de Goede).
 
  - Add statements to print debug messages in a couple of places in
    the ACPI core for easier diagnostics (Rafael Wysocki).
 
  - Clean up the ACPI processor driver slightly (Colin Ian King,
    Hanjun Guo).
 
  - Clean up the ACPI x86 boot code somewhat (Andy Shevchenko).
 
  - Add a quirk for Dell OptiPlex 9020M to the ACPI backlight
    driver (Alex Hung).
 
  - Assorted fixes, cleanups and updates related to ACPI (Amitoj Kaur
    Chawla, Bhumika Goyal, Frank Rowand, Jean Delvare, Punit Agrawal,
    Ronald Tschalär, Sumeet Pawnikar).
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJZrcE+AAoJEILEb/54YlRxVGAP/RKzkJlYlOIXtMjf4XWg5ZfJ
 RKZA68E9DW179KoBoTCVPD6/eD5UoEJ7fsWXFU2Hgp2xL3N1mZMAJHgAE4GoAwCx
 uImoYvQgdPna7DawzRIFkvkfceYxNyh+KaV9s7xne4hAwsB7JzP9yf5Ywll53+oF
 Le27/r6lDOaWhG7uYcxSabnQsWZQkBF5mj2GPzEpKDIHcLA1Vii0URzm7mAHdZsz
 vGjYhxrshKYEVdkLSRn536m1rEfp2fqsRJ5wqNAazZJr6Cs1WIfNVuv/RfduRJpG
 /zHIRAmgKV+3jp39cBpjdnexLczb1rGiCV1yZOvwCNM7jy4evL8vbL7VgcUCopaj
 fHbF34chNG/hKJd3Zn3RRCTNzCs6bv+txslOMARxji5eyr2Q4KuVnvg5LM4hxOUP
 23FvcYkBYWu4QCNLOTnC7y2OqK6WzOvDpfi7hf13Z42iNzeAUbwt1sVF0/OCwL51
 Og6blSy2x8FidKp8oaBBboBzHEiKWnXBj/Hw8KEHVcsqZv1ZC6igNRAL3tjxamU8
 98/Z2NSZHYPrrrn13tT9ywISYXReXzUF85787+0ofugvDe8/QyBH6UhzzZc/xKVA
 t329JEjEFZZSLgxMIIa9bXoQANxkeZEGsxN6FfwvQhyIVdagLF3UvCjZl/q2NScC
 9n++s32qfUBRHetGODWc
 =6Ke9
 -----END PGP SIGNATURE-----

Merge tag 'acpi-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull ACPI updates from Rafael Wysocki:
 "These include a usual ACPICA code update (this time to upstream
  revision 20170728), a fix for a boot crash on some systems with
  Thunderbolt devices connected at boot time, a rework of the handling
  of PCI bridges when setting up device wakeup, new support for Apple
  device properties, support for DMA configurations reported via ACPI on
  ARM64, APEI-related updates, ACPI EC driver updates and assorted minor
  modifications in several places.

  Specifics:

   - Update the ACPICA code in the kernel to upstream revision 20170728
     including:
      * Alias operator handling update (Bob Moore).
      * Deferred resolution of reference package elements (Bob Moore).
      * Support for the _DMA method in walk resources (Bob Moore).
      * Tables handling update and support for deferred table
        verification (Lv Zheng).
      * Update of SMMU models for IORT (Robin Murphy).
      * Compiler and disassembler updates (Alex James, Erik Schmauss,
        Ganapatrao Kulkarni, James Morse).
      * Tools updates (Erik Schmauss, Lv Zheng).
      * Assorted minor fixes and cleanups (Bob Moore, Kees Cook, Lv
        Zheng, Shao Ming).

   - Rework the initialization of non-wakeup GPEs with method handlers
     in order to address a boot crash on some systems with Thunderbolt
     devices connected at boot time where we miss an early hotplug event
     due to a delay in GPE enabling (Rafael Wysocki).

   - Rework the handling of PCI bridges when setting up ACPI-based
     device wakeup in order to avoid disabling wakeup for bridges
     prematurely (Rafael Wysocki).

   - Consolidate Apple DMI checks throughout the tree, add support for
     Apple device properties to the device properties framework and use
     these properties for the handling of I2C and SPI devices on Apple
     systems (Lukas Wunner).

   - Add support for _DMA to the ACPI-based device properties lookup
     code and make it possible to use the information from there to
     configure DMA regions on ARM64 systems (Lorenzo Pieralisi).

   - Fix several issues in the APEI code, add support for exporting the
     BERT error region over sysfs and update APEI MAINTAINERS entry with
     reviewers information (Borislav Petkov, Dongjiu Geng, Loc Ho, Punit
     Agrawal, Tony Luck, Yazen Ghannam).

   - Fix a potential initialization ordering issue in the ACPI EC driver
     and clean it up somewhat (Lv Zheng).

   - Update the ACPI SPCR driver to extend the existing XGENE 8250
     workaround in it to a new platform (m400) and to work around an
     Xgene UART clock issue (Graeme Gregory).

   - Add a new utility function to the ACPI core to support using ACPI
     OEM ID / OEM Table ID / Revision for system identification in
     blacklisting or similar and switch over the existing code already
     using this information to this new interface (Toshi Kani).

   - Fix an xpower PMIC issue related to GPADC reads that always return
     0 without extra pin manipulations (Hans de Goede).

   - Add statements to print debug messages in a couple of places in the
     ACPI core for easier diagnostics (Rafael Wysocki).

   - Clean up the ACPI processor driver slightly (Colin Ian King, Hanjun
     Guo).

   - Clean up the ACPI x86 boot code somewhat (Andy Shevchenko).

   - Add a quirk for Dell OptiPlex 9020M to the ACPI backlight driver
     (Alex Hung).

   - Assorted fixes, cleanups and updates related to ACPI (Amitoj Kaur
     Chawla, Bhumika Goyal, Frank Rowand, Jean Delvare, Punit Agrawal,
     Ronald Tschalär, Sumeet Pawnikar)"

* tag 'acpi-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (75 commits)
  ACPI / APEI: Suppress message if HEST not present
  intel_pstate: convert to use acpi_match_platform_list()
  ACPI / blacklist: add acpi_match_platform_list()
  ACPI, APEI, EINJ: Subtract any matching Register Region from Trigger resources
  ACPI: make device_attribute const
  ACPI / sysfs: Extend ACPI sysfs to provide access to boot error region
  ACPI: APEI: fix the wrong iteration of generic error status block
  ACPI / processor: make function acpi_processor_check_duplicates() static
  ACPI / EC: Clean up EC GPE mask flag
  ACPI: EC: Fix possible issues related to EC initialization order
  ACPI / PM: Add debug statements to acpi_pm_notify_handler()
  ACPI: Add debug statements to acpi_global_event_handler()
  ACPI / scan: Enable GPEs before scanning the namespace
  ACPICA: Make it possible to enable runtime GPEs earlier
  ACPICA: Dispatch active GPEs at init time
  ACPI: SPCR: work around clock issue on xgene UART
  ACPI: SPCR: extend XGENE 8250 workaround to m400
  ACPI / LPSS: Don't abort ACPI scan on missing mem resource
  mailbox: pcc: Drop uninformative output during boot
  ACPI/IORT: Add IORT named component memory address limits
  ...
2017-09-05 12:45:03 -07:00
Mark Brown ecb478bf86 Merge remote-tracking branch 'spi/topic/xlp' into spi-next 2017-09-04 15:51:34 +01:00
Mark Brown 2dcfd2814b Merge remote-tracking branches 'spi/topic/sh-msiof', 'spi/topic/stm32', 'spi/topic/sunxi', 'spi/topic/tegra' and 'spi/topic/tools' into spi-next 2017-09-04 15:51:30 +01:00