Using the hardware window into PCI config space is more reliable
and smaller/faster than using the pci_config routines. It avoids issues
with MMCONFIG etc.
Reverts: 167f53d05f
Please apply for 2.6.24
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
netif_rx_complete() should be called only
when work_done < budget.
Signed-off-by: Divy Le ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The patch ensures that a GSO skb has enough headroom
to push an encapsulating cpl_tx_pkt_lso header.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Extend the RGMII-Internal Delay specification case to include
TX-only and RX-only variants.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Previously, Internal Delay specification implied the delay be
applied to both TX and RX. This patch allows for separate TX/RX-only
internal delay specification.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow phylib specification of cases where hardware needs to configure
PHYs for Internal Delay only on either RX or TX (not both).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The code to change MTU doesn't correctly handle all the chip variations
and requirements for restarting. On Genesis chips changing MTU would just
cause receiver to hang.
Use a simpler approach of just taking link down/up if needed.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For compatiablity with sk98lin, make sure and set same values
in serial mode register.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Need to increase TX threshold when doing Jumbo frames on dual port board
to avoid underruns. (Code from sk98lin).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver would not work over fibre if other end when down then
came back up (would require reloading driver). The correct way
to manage the link the same way for both TP and fibre.
Resloves problem described in: http://lkml.org/lkml/2007/11/6/395
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make sure and retry when shutting down the MAC. This code is copied
from sk98lin driver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Receive FIFO overrun is not catastrophic condition, so don't flush when
it happens.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The calculation of usable FIFO RAM is wrong in the skge driver.
First, is doesn't take into account the reserved area on the original
SysKonnect Genesis boards. Second it has an off-by-one error because
hw->ports is either 1 or 2.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently ctc-device initialization is broken (kernel bug in
ctc_new_device).
The new network namespace code reveals a deficiency of the
ctc driver. It should make use of alloc_netdev() as described
in Documentation/networking/netdevices.txt.
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the case when the card initialization fails on a mtu change and then
close is called (due to ifdown), which frees non existent rx buffers.
- Returning appropriate error codes in init_nic function.
- In s2io_close function s2io_card_down is called only when device is up.
- In s2io_change_mtu function return value of s2io_card_up function
is checked and returned if it failed.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Fix static rate if path faster than link
IPoIB: Fix oops if xmit is called when priv->broadcast is NULL
Freeing prom memory: 956kb freed
Freeing firmware memory: 978944k freed
Freeing unused kernel memory: 180k freed
BUG: using smp_processor_id() in preemptible [00000000] code: swapper/1
caller is r4k_dma_cache_wback_inv+0x144/0x2a0
Call Trace:
[<80117af8>] r4k_dma_cache_wback_inv+0x144/0x2a0
[<802e4b84>] debug_smp_processor_id+0xd4/0xf0
[<802e4b7c>] debug_smp_processor_id+0xcc/0xf0
...
CONFIG_DEBUG_PREEMPT is enabled.
--
Bug cause is blast_dcache_range() in preemptible code [in
r4k_dma_cache_wback_inv()].
blast_dcache_range() is constructed via __BUILD_BLAST_CACHE_RANGE that
uses cpu_dcache_line_size(). It uses current_cpu_data that use
smp_processor_id() in turn. In case of CONFIG_DEBUG_PREEMPT
smp_processor_id emits BUG if we are executing with preemption
enabled.
Cpu options of cpu0 are assumed to be the superset of all processors.
Can I make the same assumptions for cache line size and fix this
issue the following way:
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The formula would yield -1 if the path is faster than the link, which
is wrong in a bad way (max throttling). Clamp to 0, which is the
correct value.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4680/1: parentheses around NR_IRQS definition
[ARM] 4679/1: AT91: Change maintainer email address
[ARM] 4675/1: pxa: fix mfp address definition error for pxa320
[ARM] 4674/1: pxa: increase LCD PCLK drive strength to fast 2mA for PXA300/PXA310
[ARM] 4673/1: pxa: add missing IRQ_SSP4 definitions for PXA3xx
[ARM] 4672/1: pxa: fix DRCMR(n) to support PXA27x and later processors
[ARM] 4665/1: fix __und_usr wrt accessing the undefined insn in user space
[ARM] 4659/1: remove possibilities for spurious false negative with __kuser_cmpxchg
[ARM] 4661/1: fix do_undefinstr wrt the enabling of IRQs
[ARM] uengine: fix memset size error
[ARM] 4648/1: i.MX/MX1 ensure more complete AITC initialization
[ARM] 4611/2: AT91: Fix GPIO buttons pins on SAM9261-EK.
[ARM] 4650/1: AT91: New-style init of I2C, support for i2c-gpio
[ARM] 4604/2: AT91: Master clock divistor on SAM9
[ARM] 4662/1: Fix PXA serial driver compilation if SERIAL_PXA_CONSOLE is disabled
[ARM] PXA ssp: unlock when ssp tries to close an invalid port
[ARM] 4654/1: pxa: update default MFP register value
[ARM] 4653/1: pxa: fix a gpio typo in mfp-pxa320.h
[ARM] 4652/1: pxa: fix a typo of pxa27x usb host clk definition
[ARM] 4651/1: pxa: add PXA3xx specific IRQ definitions
The database performance group have found that half the cycles spent
in kmem_cache_free are spent in this one call to BUG_ON. Moving it
into the CONFIG_SLAB_DEBUG-only function cache_free_debugcheck() is a
performance win of almost 0.5% on their particular benchmark.
The call was added as part of commit ddc2e812d5
with the comment that "overhead should be minimal". It may have been
minimal at the time, but it isn't now.
[ Quoth Pekka Enberg: "I don't think the BUG_ON per se caused the
performance regression but rather the virt_to_head_page() changes to
virt_to_cache() that were added later." ]
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Pekka J Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes iwl_mac_add_interface.
1. Currently only one interface is supported, instead of silently retuning
0 now it returns -EOPNOTSUPP (By Johannes Berg)
2. It enables changing mac address from user space (By Ian Schram)
Signed-off-by: Tomas Winkler <tomas@localhost.localdomain>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: linux-wireless <linux-wireless@vger.kernel.org
Cc: Ian Schram <ischram@telenet.be>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
lbs_mac_event_disconnected() was called once and then never again
upon a hardware MAC event.
The reason was that the driver didn't clean the correct bit in the interrupt
cause register of the chip.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I'm not sure why it was doing this, and I'm not sure I _want_ to know
why. But calling it NETIF_F_DYNALLOC doesn't change the fact that the
kernel believes it to be NETIF_F_IPV6_CSUM, and that IPv6 communication
is hence buggered.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix some left-over URLs and ifdefs in b43 and b43legacy drivers.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Saleem Abdulrasool <compnerd@compnerd.org>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If NR_IRQS is defined as a sum without surrounding parentheses, this may
lead to problems when used in multiplications. This may lead to problems
in:
arch/ia64/sn/kernel/irq.c:516
arch/x86/kernel/io_apic_32.c:693, 694, 699, 700
fs/proc/proc_misc.c:464
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: bridge wu <bridge.wu@marvell.com>
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some platforms (e.g. Littleton) requires LCD PCLK drive strength to be
higher than default to cope with the fast PCLK frequency.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This also fixes a sparse warning about different signedness.
Only compile tested, because i do not have the hardware.
Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Subdividing the paravirt_ops structure caused a regression in certain
non-GPL modules which try to use mmu_ops and cpu_ops. This restores the
old behaviour, and makes it consistent with the non-CONFIG_PARAVIRT case.
Takashi Iwai <tiwai@suse.de> adds:
> I took at this problem (as I have an nvidia card on one of my
> workstations), and found out that the following suffer from
> EXPORT_SYMBOL_GPL changes:
>
> * local_disable_irq(), local_irq_save*(), etc.
> * MSR-related macros like rdmsr(), wrmsr(), read_cr0(), etc.
> wbinvd(), too.
> * pmd_val(), pgd_val(), etc are all involved with pv_mm_ops.
> pmd_large() and pmd_bad() is also indirectly involved.
> __flush_tlb() and friends suffer, too.
Christoph Hellwig objects to this patch on the grounds that modules
shouldn't be using these operations anyway. I don't think this is a
particularly good reason to reject the patch, for several reasons:
1. These operations are still available to modules when not using
CONFIG_PARAVIRT, since they are implicitly exported as inline
functions via the kernel headers. Exporting the same functionality as
GPL-only symbols just adds a gratuitious difference between
CONFIG_PARAVIRT and non-CONFIG_PARAVIRT configurations. If we really
think these operations are not for module use (or non-GPL module use),
then we should solve the problem in a general way.
2. It's a regression from previous kernels, which would work these
modules even with CONFIG_PARAVIRT enabled.
3. The operations in question seem pretty reasonable for modules to
use. The control registers/MSRs can be accessed directly anyway, so there's
no benefit in preventing modules from using standard interfaces. And it seems
reasonable to allow a graphics driver to create its own mappings if it wants.
Therefore, I think this patch should go in for 2.6.24. If people
really think that these operations should not be available to modules,
then we can address that separately.
Signed-off-by: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com>
Cc: Tobias Powalowski <t.powa@gmx.de>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Keep lguest from being enabled on VISWS or VOYAGER configs, just as is
already done for VMI and XEN. Otherwise randconfigs with VISWS and LGUEST
have this problem:
In file included from arch/x86/kernel/setup_32.c:61:
include/asm-x86/mach-visws/setup_arch.h:8:1: warning: "ARCH_SETUP" redefined
In file included from include/asm/msr.h:80,
from include/asm/processor_32.h:17,
from include/asm/processor.h:2,
from include/asm/thread_info_32.h:16,
from include/asm/thread_info.h:2,
from include/linux/thread_info.h:21,
from include/linux/preempt.h:9,
from include/linux/spinlock.h:49,
from include/linux/seqlock.h:29,
from include/linux/time.h:8,
from include/linux/timex.h:57,
from include/linux/sched.h:53,
from arch/x86/kernel/setup_32.c:24:
include/asm/paravirt.h:458:1: warning: this is the location of the previous definition
(and of course, this happens because kconfig does not follow dependencies
when [evil] select is used...)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ACPI uses NR_CPUS in various loops and in some it accesses per cpu data of
processors that are not present(!) and that will never be present.
The pointers to per cpu data are typically not initialized for processors
that are not present. So we seem to be reading something here from offset
0 in memory.
Make ACPI use nr_cpu_ids instead. That stops at the end of the possible
processors.
Convert one loop to NR_CPUS to use the cpu_possible map instead. That way
ranges of processor that can never be brought online are skipped during the
loop.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make them depend on TCGETS2. If that one is implemented the rest should be
there as well.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In wait_task_stopped() exit_code already contains the right value for the
si_status member of siginfo, and this is simply set in the non WNOWAIT
case.
If you call waitid() with a stopped or traced process, you'll get the signal
in siginfo.si_status as expected -- however if you call waitid(WNOWAIT) at the
same time, you'll get the signal << 8 | 0x7f
Pass it unchanged to wait_noreap_copyout(); we would only need to shift it
and add 0x7f if we were returning it in the user status field and that
isn't used for any function that permits WNOWAIT.
Signed-off-by: Scott James Remnant <scott@ubuntu.com>
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen Hemminger
Divy Le Ray
Kim Phillips
Peter Tiedemann
Sreenivasa Honnur
Jeff Garzik
Linus Torvalds
Ralf Baechle
Pavel Kiryukhin
Joachim Fenkes
Matthew Wilcox
Joonwoo Park
Tomas Winkler
Holger Schurig
David Woodhouse
Joe Perches
Stefano Brivio
Saleem Abdulrasool
Russell King
Roel Kluin
Andrew Victor
eric miao
Andre Haupt
Jeremy Fitzhardinge
Randy Dunlap
Christoph Lameter
Heiko Carstens
Scott James Remnant
Mike Christie