Add support for the Infineon TLE62x0 series of low-side driver chips, such
as the TLE6220 or TLE6230. These can be viewed as output GPIOs specialized
for power switching applications. The driver provides a userspace
interface to those GPIOs, and to the switch status they provide.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tweak Kconfig for the S3C24XX SPI controller drivers. Both use the bitbang
framework; only one previously said that. Plus in this case "select" is
the right way to manage that dependency, since folk will not know up front
to enable bitbang in order to even see those S3C drivers in order to enable
them.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update chipselect handling for atmel_spi:
* Teach it how to leave chipselect active between messages; this
helps various drivers work better.
* Cope with at91rm0200 errata: nCS0 can't be managed with GPIOs.
The MR.PCS value is now updated whenever a chipselect changes.
(This requires SPI pinmux init for that controller to change,
and also testing on rm9200; doesn't break at91sam9 or avr32.)
* Fix minor glitches: spi_setup() must leave chipselects inactive,
as must removal of the spi_device.
Also tweak diagnostic messaging to be a bit more useful.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor updates to atmel_spi:
- DMA:
* Comments to explain the DMA policies
* Report any mapping errors from spi_transfer()
* Remove extra loop for DMA mapping
- Diagnostics: report minimum clock rate, if we need to reject a
spi_setup() request because that rate is too low.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MPC83xx SPI controller clock divider can divide the system clock by not
more then 1024. The spi_mpc83xx driver does not check this and silently
writes garbage to the SPI controller registers when asked to run at lower
frequencies. I've tried to run the SPI on a 266MHz MPC8349E with 100kHz
for debugging a bus problem and suddenly was confronted with a 2nd problem
to debug.. ;-)
The patch adds an additional check which avoids writing garbage to the SPI
controller registers and warn the user about it. This might help others to
avoid simmilar problems.
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a driver for the LM70-LLP parport adapter, which is an eval board
for the LM70 temperature sensor. For those without that board, it may be a
simpler example of a parport-to-SPI adapter then spi_butterfly.
Signed-off-by: Kaiwan N Billimoria <kaiwan@designergraphix.com>
Doc, coding style, and interface updates; build fixes. Minor rename.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Get rid of annoying GCC warning on 32-bit platforms.
drivers/spi/spidev.c: In function 'spidev_message':
drivers/spi/spidev.c:184: warning: cast to pointer from integer of different size
drivers/spi/spidev.c:216: warning: cast to pointer from integer of different size
The trick is to add an extra cast using "ptrdiff_t" to convert the u64 to
the correct size integer, and only then casting it into a "void *" pointer.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new spi->mode bit: SPI_3WIRE, for chips where the SI and SO signals
are shared (and which are thus only half duplex). Update the LM70 driver
to require support for that hardware mode from the controller.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor SPI controller driver updates: make the setup() methods reject
spi->mode bits they don't support, by masking aginst the inverse of bits
they *do* support. This insures against misbehavior later when new mode
bits get added.
Most controllers can't support SPI_LSB_FIRST; more handle SPI_CS_HIGH.
Support for all four SPI clock/transfer modes is routine.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IBMASM: must depend on CONFIG_INPUT
The driver registers couple of input devices and therefore must depend
on CONFIG_INPUT.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Vernon Mauery <vernux@us.ibm.com>
Cc: Max Asbock <masbock@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IBMASM: miscellaneous fixes
Fix some minor issues, such as:
- properly set up ID of keyboard device (was mixed up with mouse)
- constify translation tables
- change some variables to #defines
- set up input device's parent to form proper sysfs hierarchy
- minor formatting changes
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Vernon Mauery <vernux@us.ibm.com>
Cc: Max Asbock <masbock@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IBMASM: don't use extern in function declarations
We normally don't use extern in function declarations located in header files.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Vernon Mauery <vernux@us.ibm.com>
Cc: Max Asbock <masbock@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a driver for the SB1250 DUART, a dual serial port implementation
included in the Broadcom family of SOCs descending from the SiByte SB1250
MIPS64 chip multiprocessor. It is a new implementation replacing the
old-fashioned driver currently present in the linux-mips.org tree. It
supports all the usual features one would expect from a(n asynchronous)
serial driver, including modem line control (as far as hardware supports it
-- there is edge detection logic missing from the DCD and RI lines and the
driver does not implement polling of these lines at the moment), the serial
console, BREAK transmission and reception, including the magic SysRq. The
receive FIFO threshold is not maintained though.
The driver was tested with a SWARM board which uses a BCM1250 SOC (which is
dual MIPS64 CMP) and has both ports of the single DUART implemented wired
externally. Both were tested. Testing included using the ports as
terminal lines at 1200bps (which is the ports minimum), 115200bps and a
couple of random speeds inbetween. The modem lines were verified to
operate correctly. No testing was performed with a use as a network
interface, like with SLIP or PPP.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No need to warn unregister_blkdev() failure by caller. (The previous patch
makes unregister_blkdev() print error message in error case)
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No need to warn unregister_blkdev() failure by the callers. (The previous
patch makes unregister_blkdev() print error message in error case)
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested on Xilinx Virtex ppc405, Katmai 440SPe, and Microblaze
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: John William <jwilliams@itee.uq.edu.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rolling forward PCMCIA driver, it was discovered that the indentation in
existing one, as well as in BSP side are very odd. This patch is just result
of Lindent run ontop of culprit files.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kmalloc_node() and kmem_cache_alloc_node() were not available in a zeroing
variant in the past. But with __GFP_ZERO it is possible now to do zeroing
while allocating.
Use __GFP_ZERO to remove the explicit clearing of memory via memset whereever
we can.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-patches' of ssh://master.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: add idr_init to drm_stub.c
drm: fix problem with SiS typedef with sisfb enabled.
z/VM Unit record character device driver to access VM reader, punch,
and printer.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A number of small changes to vmcp:
- Change preferred email address.
- Use PRINT_xxx machros from debug.h like most s390 drivers, define
"vmcp:" as PRINTK_HEADER and wrap error message at column 80.
- Add error number to error message.
- Update copyright, as I touched this file.
- Small whitespace diff.
- Use mutex instead of semaphore (Thanks Heiko for the patch)
- Don't register debug feature on failure.
- Check debug feature registration on init to avoid a potential oops
on unload if the debug feature could not be registered--> 2 more
messages.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When running QIOASSIST enabled qdio devices in a z/VM environment
the output queue for such devices stall in heavy workload situations.
When SQBS and EQBS instructions returns CCQ=96 qdio does not reissue
the instruction again with the register settings done by millicode
but processed the returned qdio buffer. This is wrong. qdio has to
reissue the instruction once again on CCQ=96, as we already do it
for CCQ=97.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'drm-patches' of ssh://master.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: convert drawable code to using idr
drm: convert drm context code to use Linux idr
This converts the code for allocating drawables to the Linux idr,
Fixes from: Michel Dänzer <michel@tungstengraphics.com>, Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This converts the drm context allocator to an idr, using the new idr
interface features from Kristian.
Fixes from Kristian Hoegsberg <krh@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (209 commits)
[POWERPC] Create add_rtc() function to enable the RTC CMOS driver
[POWERPC] Add H_ILLAN_ATTRIBUTES hcall number
[POWERPC] xilinxfb: Parameterize xilinxfb platform device registration
[POWERPC] Oprofile support for Power 5++
[POWERPC] Enable arbitary speed tty ioctls and split input/output speed
[POWERPC] Make drivers/char/hvc_console.c:khvcd() static
[POWERPC] Remove dead code for preventing pread() and pwrite() calls
[POWERPC] Remove unnecessary #undef printk from prom.c
[POWERPC] Fix typo in Ebony default DTS
[POWERPC] Check for NULL ppc_md.init_IRQ() before calling
[POWERPC] Remove extra return statement
[POWERPC] pasemi: Don't auto-select CONFIG_EMBEDDED
[POWERPC] pasemi: Rename platform
[POWERPC] arch/powerpc/kernel/sysfs.c: Move NUMA exports
[POWERPC] Add __read_mostly support for powerpc
[POWERPC] Modify sched_clock() to make CONFIG_PRINTK_TIME more sane
[POWERPC] Create a dummy zImage if no valid platform has been selected
[POWERPC] PS3: Bootwrapper support.
[POWERPC] powermac i2c: Use mutex
[POWERPC] Schedule removal of arch/ppc
...
Fixed up conflicts manually in:
Documentation/feature-removal-schedule.txt
arch/powerpc/kernel/pci_32.c
arch/powerpc/kernel/pci_64.c
include/asm-powerpc/pci.h
and asked the powerpc people to double-check the result..
Mixing putchar() and write() hvcalls does not work %100
correctly. But we should be using write() all the time
if we can, even from ->start_tx(), anyways.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains errata fixes for the cicada phy. It only renamed the
defines to be phy specific.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reorder functions in atl1_main into more logical groupings to make the
code easier to follow. This patch is large, but it's harmless; it neither
adds nor removes any functionality whatsoever.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move excessively indented code to separate functions. Also move ring
pointer initialization to its own function.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix indentation, remove dead code, improve some comments, change dev_dbg to
dev_printk.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove unused structure members, improve comments, break long comment lines,
rename a constant to be consistent with others in the file.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch is for cdc subset to support Mavell vendor/product ID.
Signed-off-by: Jing Xiang <everxiang@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove nonsensical limit in the tx done routine. Specifically,
the loop will always terminate after processing <= 1 rings worth
of frames, as the mcp index is not refetched, so the removed
conditional could never be true.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A long time ago we used OCP with the gianfar driver. Eventually when
we kill arch/ppc including this will cause issues so lets just kill it now.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
CONFIG_EP93XX_ETH=y, CONFIG_MII=n results in an obvious link error.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert the macb driver to use the generic PHY layer in
drivers/net/phy.
Signed-off-by: Frederic RODO <f.rodo@til-technologies.fr>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add barrier to loop where atomic variable is evaluated.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For large incoming packets > PAGE_SIZE/2 qeth creates a fragmented skb
by adding pointers to qdio pages to the fragment list of the skb.
This avoids allocating big chunks of consecutive memory. Also copying
data from the qdio buffer to the skb is economized.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for DLPAR memory add to the eHEA driver. To detect
whether memory was added the driver uses its own memory mapping table and
checks for kernel addresses whether they're located in already known memory
sections. If not the function ehea_rereg_mrs() is triggered which performs
a rebuild of the mapping table and a re-registration of the global memory
region.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a potential null dereference bug where we dereference
nic before a null check. This patch simply moves the dereferencing
after the null check.
Signed-off-by: Micah Gruber < micah.gruber@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'drm-patches' of ssh://master.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: remove core typedefs from the ioc32 wrappers
drm: remove sarea typedefs
drm: detypedef the hashtab and more of sman
drm: de-typedef sman
drm: detypedeffing continues...
drm: detypef waitlist/freelist/buf_entry/device_dma/drm_queue structs
drm: drop drm_vma_entry_t, drm_magic_entry_t
drm: drop drm_buf_t typedef
drm: fixup other drivers for typedef removals
drm: remove drm_file_t, drm_device_t and drm_head_t typedefs
drm: remove a bunch of typedefs on the userspace interface
r300: updates register header
radeon: add support for vblank on crtc2
drm: cleanup list initialisation
drm: fix typo on code drm getsarea
drm: remove DRM_GETSAREA and replace with drm_getsarea function
drm: cleanup use of Linux list handling macros
This corrects the following compile error introduced by the merge of the
new bsg layer in commit e245befce7af0a1e1347079ed62695b059594bd4:
caglar@zangetsu linux-2.6 $ make
CHK include/linux/version.h
CHK include/linux/utsrelease.h
CALL scripts/checksyscalls.sh
CHK include/linux/compile.h
LD drivers/block/built-in.o
CC [M] drivers/block/cciss.o
drivers/block/cciss.c: In function `cciss_ioctl':
drivers/block/cciss.c:1173: warning: passing arg 2 of `scsi_cmd_ioctl' from incompatible pointer type
drivers/block/cciss.c:1173: warning: passing arg 3 of `scsi_cmd_ioctl' makes pointer from integer without a cast
drivers/block/cciss.c:1173: warning: passing arg 4 of `scsi_cmd_ioctl' makes integer from pointer without a cast
drivers/block/cciss.c:1173: error: too few arguments to function `scsi_cmd_ioctl'
...
make[2]: *** [drivers/block/cciss.o] Hata 1
make[1]: *** [drivers/block] Hata 2
make: *** [drivers] Hata 2
Signed-off-by: S.Çağlar Onur <caglar@pardus.org.tr>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'bsg' of git://git.kernel.dk/data/git/linux-2.6-block: (25 commits)
bsg: Kconfig updates
bsg: add SCSI transport-level request support
bsg: add bidi support
add a struct request pointer to the request structure
bsg: fix the deadlock on discarding done commands
bsg: fix a blocking read bug
bsg: minor bug fixes
improve bsg device allocation
bind bsg to all SCSI devices
bsg: bind bsg to request_queue instead of gendisk
bsg: add a request_queue argument to scsi_cmd_ioctl()
bsg: simplify __bsg_alloc_command failpath
bsg: add cheasy error checks for sysfs stuff
Add queue resizing support
Replace s32, u32 and u64 with __s32, __u32 and __u64 in bsg.h for userspace
bsg: silence a bogus gcc warning
bsg: style cleanup
bsg: use u32 etc instead of uint32_t
bsg: add SG_IO to SG v4
bsg: replace SG v3 with SG v4
...
* 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block:
splice: direct splicing updates ppos twice
more ACSI removal
umem: Fix match of pci_ids in umem driver
umem: Remove references to dead CONFIG_MM_MAP_MEMORY variable
remove the documentation for the legacy CDROM drivers
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (26 commits)
[SPARC64]: Fix UP build.
[SPARC64]: dr-cpu unconfigure support.
[SERIAL]: Fix console write locking in sparc drivers.
[SPARC64]: Give more accurate errors in dr_cpu_configure().
[SPARC64]: Clear cpu_{core,sibling}_map[] in smp_fill_in_sib_core_maps()
[SPARC64]: Fix leak when DR added cpu does not bootup.
[SPARC64]: Add ->set_affinity IRQ handlers.
[SPARC64]: Process dr-cpu events in a kthread instead of workqueue.
[SPARC64]: More sensible udelay implementation.
[SPARC64]: SMP build fixes.
[SPARC64]: mdesc.c needs linux/mm.h
[SPARC64]: Fix build regressions added by dr-cpu changes.
[SPARC64]: Unconditionally register vio_bus_type.
[SPARC64]: Initial LDOM cpu hotplug support.
[SPARC64]: Fix setting of variables in LDOM guest.
[SPARC64]: Fix MD property lifetime bugs.
[SPARC64]: Abstract out mdesc accesses for better MD update handling.
[SPARC64]: Use more mearningful names for IRQ registry.
[SPARC64]: Initial domain-services driver.
[SPARC64]: Export powerd facilities for external entities.
...
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: (68 commits)
sh: sh-rtc support for SH7709.
sh: Revert __xdiv64_32 size change.
sh: Update r7785rp defconfig.
sh: Export div symbols for GCC 4.2 and ST GCC.
sh: fix race in parallel out-of-tree build
sh: Kill off dead mach.c for hp6xx.
sh: hd64461.h cleanup and added comments.
sh: Update the alignment when 4K stacks are used.
sh: Add a .bss.page_aligned section for 4K stacks.
sh: Don't let SH-4A clobber SH-4 CFLAGS.
sh: Add parport stub for SuperIO ports.
sh: Drop -Wa,-dsp for DSP tuning.
sh: Update dreamcast defconfig.
fb: pvr2fb: A few more __devinit annotations for PCI.
fb: pvr2fb: Fix up section mismatch warnings.
sh: Select IPR-IRQ for SH7091.
sh: Correct __xdiv64_32/div64_32 return value size.
sh: Fix timer-tmu build for SH-3.
sh: Add cpu and mach links to CLEAN_FILES.
sh: Preliminary support for the SH-X3 CPU.
...
sparc64:
drivers/sbus/char/cpwatchdog.c: In function `wd_toggleintr':
drivers/sbus/char/cpwatchdog.c:523: error: implicit declaration of function `readb'
drivers/sbus/char/cpwatchdog.c:533: error: implicit declaration of function `writeb'
drivers/sbus/char/cpwatchdog.c: In function `wd_pingtimer':
drivers/sbus/char/cpwatchdog.c:545: error: implicit declaration of function `readw'
drivers/sbus/char/cpwatchdog.c: In function `wd_starttimer':
drivers/sbus/char/cpwatchdog.c:584: error: implicit declaration of function `writew'
drivers/sbus/char/cpwatchdog.c: In function `wd_init':
drivers/sbus/char/cpwatchdog.c:767: error: implicit declaration of function `ioremap'
drivers/sbus/char/cpwatchdog.c:767: warning: assignment makes pointer from integer without a cast
drivers/sbus/char/cpwatchdog.c: In function `wd_cleanup':
drivers/sbus/char/cpwatchdog.c:849: error: implicit declaration of function `iounmap'
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not mark sn_sal_console_setup as __init since it's referenced from
non init data structures.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In drivers/pnp/isapnp/core.c::isapnp_read_tag() there is a test of 'type'
being == 0 a bit down in the function. That test doesn't make any sense.
If 'type' could indeed be NULL, then the test happens way too late as we'd
already have tried to dereference the pointer earlier and looking at the
callers it also turns out that there is no way type can ever actually be
NULL.
So the test is completely pointless and should just be removed.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Again this check is wrong now, and un-needed
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We've been using the 'new locking' for a long time now so it seems
pointless keeping the old one around. Remove it and undo the macros it
uses back into real code for readability. Remove the bogus 'no termios
change' checks.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Morten Helgesen <morten@sourcepoet.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lots of serial drivers check and optimise for setting the termios values to
the ones they were before. This is pointless and the check is wrong
anyway. Remove the checks on the serial drivers. If we ever do need such
a check put it back in the tty layer instead _once_!
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using dev_to_node(&dev->dev) to get node, and kmalloc_node to dma buffer on
corresponding node dma pool
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The IO port range requested by parport_pc.c:sio_ite_8872_probe is too small.
The IO-ports of ttyS1 (0x2f8) will be missconfigured by the ITE-chip. The ITE
starts looking for the chip a 0x2a0. An IO-portrange of 32 will not overwrite
the ports of ttyS1. Therefore register 0x60 should be written with
0xe5000000, enabling the ITE and setting IO-portsize to 32 bytes.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kcdrwd() is a kernel thread, all signals are ignored.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
adb_probe_task() is forked by "events" thread, all signals are ignored, no
need to play with signal blocking/flushing.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove not only the references to Cobalt NVRAM, but the header file as
well.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Tim Hockin <thockin@hockin.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add TTY input auditing, used to audit system administrator's actions. This is
required by various security standards such as DCID 6/3 and PCI to provide
non-repudiation of administrator's actions and to allow a review of past
actions if the administrator seems to overstep their duties or if the system
becomes misconfigured for unknown reasons. These requirements do not make it
necessary to audit TTY output as well.
Compared to an user-space keylogger, this approach records TTY input using the
audit subsystem, correlated with other audit events, and it is completely
transparent to the user-space application (e.g. the console ioctls still
work).
TTY input auditing works on a higher level than auditing all system calls
within the session, which would produce an overwhelming amount of mostly
useless audit events.
Add an "audit_tty" attribute, inherited across fork (). Data read from TTYs
by process with the attribute is sent to the audit subsystem by the kernel.
The audit netlink interface is extended to allow modifying the audit_tty
attribute, and to allow sending explanatory audit events from user-space (for
example, a shell might send an event containing the final command, after the
interactive command-line editing and history expansion is performed, which
might be difficult to decipher from the TTY input alone).
Because the "audit_tty" attribute is inherited across fork (), it would be set
e.g. for sshd restarted within an audited session. To prevent this, the
audit_tty attribute is cleared when a process with no open TTY file
descriptors (e.g. after daemon startup) opens a TTY.
See https://www.redhat.com/archives/linux-audit/2007-June/msg00000.html for a
more detailed rationale document for an older version of this patch.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Miloslav Trmac <mitr@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Casey Schaufler <casey@schaufler-ca.com>
Cc: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The intel-rng printed a nice well formatted message when the port was
disabled. Someone then came along and blindly trashed it by screwing up a
trim down to 80 columns.
Put it back into the right format and keep the overlong lines as the result
is also MUCH easier to read in this specific case.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Michael Buesch <mb@bu3sch.de>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Despite repeated attempts over the last two and half years, this driver
seems somewhat persistant. Remove its deprecated status as it has existing
users who may not be in a position to migrate their apps to O_DIRECT.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use NULL instead of 0 for pointer:
drivers/misc/sony-laptop.c:1920:6: warning: Using plain integer as NULL pointer
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the no longer used sonypi_camera_command().
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes dead keys and copy/paste of non-ASCII characters in UTF-8
mode on Linux console. See more details about the original patch at:
http://chris.heathens.co.nz/linux/utf8.html
Already posted on
(Oldest) http://lkml.org/lkml/2003/5/31/148http://lkml.org/lkml/2005/12/24/69
(Recent) http://lkml.org/lkml/2006/8/7/75
[bunk@stusta.de: make drivers/char/selection.c:store_utf8() static]
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Alexander E. Patrakov <patrakov@ums.usu.ru>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I forgot to remove capability.h from mm.h while removing sched.h! This
patch remedies that, because the only inline function which was using
CAP_something was made out of line.
Cross-compile tested without regressions on:
all powerpc defconfigs
all mips defconfigs
all m68k defconfigs
all arm defconfigs
all ia64 defconfigs
alpha alpha-allnoconfig alpha-defconfig alpha-up
arm
i386 i386-allnoconfig i386-defconfig i386-up
ia64 ia64-allnoconfig ia64-defconfig ia64-up
m68k
mips
parisc parisc-allnoconfig parisc-defconfig parisc-up
powerpc powerpc-up
s390 s390-allnoconfig s390-defconfig s390-up
sparc sparc-allnoconfig sparc-defconfig sparc-up
sparc64 sparc64-allnoconfig sparc64-defconfig sparc64-up
um-x86_64
x86_64 x86_64-allnoconfig x86_64-defconfig x86_64-up
as well as my two usual configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RXBRK field in the AT91/AT32 USART status register has the
following definition according to e.g. the AT32AP7000 data sheet:
RXBRK: Break Received/End of Break
0: No Break received or End of Break detected since the last RSTSTA.
1: Break Received or End of Break detected since the last RSTSTA.
Thus, for each break, the USART sets the RXBRK bit twice. This patch
modifies the driver to report the break event to the serial core only
once by keeping track of whether a break condition is currently
active. The break_active flag is reset as soon as a character is
received, so even if we miss the start-of-break interrupt this should
do the right thing.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ivan Kuten <ivan.kuten@promwad.com>
Cc: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@rfo.atmel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Continuing the work started in 411f0f3edc ...
This enables code with a dma path, that compiles away, to build without
requiring additional code factoring. It also prevents code that calls
dma_alloc_coherent and dma_free_coherent from linking whereas previously
the code would hit a BUG() at run time. Finally, it allows archs that set
!HAS_DMA to delete their asm/dma-mapping.h file.
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: <geert@linux-m68k.org>
Cc: <zippel@linux-m68k.org>
Cc: <spyro@f2s.com>
Cc: <ysato@users.sourceforge.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tty_ioctl, little whitespace cleanup
the point is to make
while (++i < n_baud_table);
clear and assign it to the do { } loop
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This config symbol name is confusing and unneeded/unwanted, so just
change it to MISC_DEVICES.
*
* Misc devices
*
Misc devices (MISC_STRANGE_DEV) [Y/n] (NEW)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Also remove needless casts.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We gets lots of these when the kernel is running on a hypervisor. Zach says
"a guest kernel trying to get high frequency RTC will also be inaccurate, and
inevitably will have unhidable interrupt lateness."
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Check the return of mutex_lock_interruptible() in drivers/char/rocket.c and
return ERESTARTSYS if we were interrupted.
Signed-off-by: Satyam Sharma <satyam.sharma@gmail.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make some offending drivers depend on it and set CONFIG_ARCH_NO_VIRT_TO_BUS
for ppc64 so that we don't build those drivers.
This gets PowerPC allmodconfig and allyesconfig much closer to building.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Al Viro <viro@ftp.linux.org.uk>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove defines of TRUE and FALSE
* not used in the file
* the file is not included somewhere else
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simple and stupid - just use the helpers.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The I2O driver uses two semaphores as mutexes. Use the mutex API instead of
the (binary) semaphores.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Without this a tty write could block if a previous blocking tty write was
in progress on the same tty and blocked by a line discipline or hardware
event. Originally found and reported by Dave Johnson.
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Dave Johnson <djohnson+linux-kernel@sw.starentnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have an API function for this now.
Cc: Zhang Yanmin <yanmin.zhang@intel.com>
Cc: Greg KH <greg@kroah.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before calling init_hwif_default, ide_unregister gets lock ide_lock and
disables irq. init_hwif_default calls ide_default_io_base which calls
pci_get_device and later pci_get_subsys tries to apply for semaphore
pci_bus_sem and goes to sleep.
Mostly, pci_get_device should be called when irq is turned on.
ide_default_io_base just needs find if list pci_devices is empty.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Cc: Greg KH <greg@kroah.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Kylene Hall <kjhall@us.ibm.com>
Cc: Marcel Selhorst <tpm@selhorst.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu",
so that the user can disable all the options in that menu at once
instead of having to disable each option separately.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Acked-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu",
so that the user can disable all the options in that menu at once
instead of having to disable each option separately.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Acked-by: Miguel Ojeda Sandonis <maxextreme@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mspec_mmap was setting VM_LOCKED (without adjusting locked_vm): don't do
that, it serves no purpose in 2.6, other than to mess up the locked_vm
accounting - mspec's pages won't get reclaimed anyway. Thanks to Dmitry
Monakhov for raising the issue.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Jes Sorensen <jes@sgi.com>
Cc: Dmitry Monakhov <dmonakhov@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Beacuse SERIAL_PORT_DFNS is removed from include/asm-i386/serial.h and
include/asm-x86_64/serial.h. the serial8250_ports need to be probed late in
serial initializing stage. the console_init=>serial8250_console_init=>
register_console=>serial8250_console_setup will return -ENDEV, and console
ttyS0 can not be enabled at that time. need to wait till uart_add_one_port in
drivers/serial/serial_core.c to call register_console to get console ttyS0.
that is too late.
Make early_uart to use early_param, so uart console can be used earlier. Make
it to be bootconsole with CON_BOOT flag, so can use console handover feature.
and it will switch to corresponding normal serial console automatically.
new command line will be:
console=uart8250,io,0x3f8,9600n8
console=uart8250,mmio,0xff5e0000,115200n8
or
earlycon=uart8250,io,0x3f8,9600n8
earlycon=uart8250,mmio,0xff5e0000,115200n8
it will print in very early stage:
Early serial console at I/O port 0x3f8 (options '9600n8')
console [uart0] enabled
later for console it will print:
console handover: boot [uart0] -> real [ttyS0]
Signed-off-by: <yinghai.lu@sun.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Gerd Hoffmann <kraxel@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some RS-232 devices require DTR to be asserted before they can be used. DTR
is normally asserted in uart_startup() when the port is opened. But we don't
actually open serial console ports, so assert DTR when the port is added.
BTW:
earlyprintk and early_uart are hard coded to set DTR/RTS.
rmk says
The only issue I can think of is the possibility for an attached modem to
auto-answer or maybe even auto-dial before the system is ready for it to do
so. Might have an undesirable cost implication for some running with such a
setup.
Apart from that, I can't think of any other side effect of this specific
patch.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Andi Kleen <ak@suse.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Gerd Hoffmann <kraxel@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes some code that became dead code after the ATARI_ACSI
removal.
It also indirectly fixes the following bug introduced by
commit c2bcf3b8978c291e1b7f6499475c8403a259d4d6:
config ATARI_SLM
tristate "Atari SLM laser printer support"
- depends on ATARI && ATARI_ACSI!=n
+ depends on ATARI
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
the pci device list for umem was not using PCI_DEVICE, so the
subvendor/subdevice fields were not set to ANY, so matching
didn't work properly.
Change to use PCI_DEVICE.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Mirror the logic in 8250 for proper console write locking
when SYSRQ is triggered or an OOPS is in progress.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we have to be able to handle MD updates, having an in-tree
set of data structures representing the MD objects actually makes
things more painful.
The MD itself is easy to parse, and we can implement the existing
interfaces using direct parsing of the MD binary image.
The MD is now reference counted, so accesses have to now take the
form:
handle = mdesc_grab();
... operations on MD ...
mdesc_release(handle);
The only remaining issue are cases where code holds on to references
to MD property values. mdesc_get_property() returns a direct pointer
to the property value, most cases just pull in the information they
need and discard the pointer, but there are few that use the pointer
directly over a long lifetime. Those will be fixed up in a subsequent
changeset.
A preliminary handler for MD update events from domain services is
there, it is rudimentry but it works and handles all of the reference
counting. It does not check the generation number of the MDs,
and it does not generate a "add/delete" list for notification to
interesting parties about MD changes but that will be forthcoming.
Signed-off-by: David S. Miller <davem@davemloft.net>
Only at the CPU_DYING stage can we be sure that no user process will
be scheduled onto the cpu and oops when trying to use virtualization
extensions.
Signed-off-by: Avi Kivity <avi@qumranet.com>
The hotplug IPIs can be called from the cpu on which we are currently
running on, so use on_cpu(). Similarly, drop on_each_cpu() for the
suspend/resume callbacks, as we're in atomic context here and only one
cpu is up anyway.
Signed-off-by: Avi Kivity <avi@qumranet.com>
By keeping track of which cpus have virtualization enabled, we
prevent double-enable or double-disable during hotplug, which is a
very fatal oops.
Signed-off-by: Avi Kivity <avi@qumranet.com>
kvm uses a pseudo filesystem, kvmfs, to generate inodes, a job that the
new anonymous inodes source does much better.
Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch adds an implementation to the svm is_disabled function to
detect reliably if the BIOS disabled the SVM feature in the CPU. This
fixes the issues with kernel panics when loading the kvm-amd module on
machines where SVM is available but disabled.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Protected mode code may have corrupted the real-mode tss, so re-initialize
it when switching to real mode.
Signed-off-by: Avi Kivity <avi@qumranet.com>
When writing to normal memory and the memory area is unchanged the write
can be safely skipped, avoiding the costly kvm_mmu_pte_write.
Signed-Off-By: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
When the old value and new one are the same the emulator skips the
write; this is undesirable when the destination is a MMIO area and the
write shall be performed regardless of the previous value. This
optimization breaks e.g. a Linux guest APIC compiled without
X86_GOOD_APIC.
Remove the check and perform the writeback stage in the emulation unless
it's explicitly disabled (currently push and some 2 bytes instructions
may disable the writeback).
Signed-Off-By: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
With kernel-injected interrupts, we need to check for interrupts on
lightweight exits too.
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
If the time stamp counter goes backwards, a guest delay loop can become
infinite. This can happen if a vcpu is migrated to another cpu, where
the counter has a lower value than the first cpu.
Since we're doing an IPI to the first cpu anyway, we can use that to pick
up the old tsc, and use that to calculate the adjustment we need to make
to the tsc offset.
Signed-off-by: Avi Kivity <avi@qumranet.com>
When a vcpu causes a shadow tlb entry to have reduced permissions, it
must also clear the tlb on remote vcpus. We do that by:
- setting a bit on the vcpu that requests a tlb flush before the next entry
- if the vcpu is currently executing, we send an ipi to make sure it
exits before we continue
Signed-off-by: Avi Kivity <avi@qumranet.com>
A vcpu can pin up to four mmu shadow pages, which means the freeing
loop will never terminate. Fix by first unpinning shadow pages on
all vcpus, then freeing shadow pages.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Switch guest paging context may require us to allocate memory, which
might fail. Instead of wiring up error paths everywhere, make context
switching lazy and actually do the switch before the next guest entry,
where we can return an error if allocation fails.
Signed-off-by: Avi Kivity <avi@qumranet.com>
This was once used to avoid accessing the guest pte when upgrading
the shadow pte from read-only to read-write. But usually we need
to set the guest pte dirty or accessed bits anyway, so this wasn't
really exploited.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Always set the accessed and dirty bit (since having them cleared causes
a read-modify-write cycle), always set the present bit, and copy the
nx bit from the guest.
Signed-off-by: Avi Kivity <avi@qumranet.com>
With guest smp, a second vcpu might see partial updates when the first
vcpu services a page fault. So delay all updates until we have figured
out what the pte should look like.
Note that on i386, this is still not completely atomic as a 64-bit write
will be split into two on a 32-bit machine.
Signed-off-by: Avi Kivity <avi@qumranet.com>
This prevents some work from being performed twice, and, more importantly,
reduces the number of places where we modify shadow ptes.
Signed-off-by: Avi Kivity <avi@qumranet.com>
We will need the accessed bit (in addition to the dirty bit) and
also write access (for setting the dirty bit) in a future patch.
Signed-off-by: Avi Kivity <avi@qumranet.com>
KVM compilation fails for some .configs. This fixes it.
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu",
so that the user can disable all the options in that menu at once
instead of having to disable each option separately.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Avi Kivity <avi@qumranet.com>
MSR_EFER.LME/LMA bits are automatically save/restored by VMX
hardware, KVM only needs to save NX/SCE bits at time of heavy
weight VM Exit. But clearing NX bits in host envirnment may
cause system hang if the host page table is using EXB bits,
thus we leave NX bits as it is. If Host NX=1 and guest NX=0, we
can do guest page table EXB bits check before inserting a shadow
pte (though no guest is expecting to see this kind of gp fault).
If host NX=0, we present guest no Execute-Disable feature to guest,
thus no host NX=0, guest NX=1 combination.
This patch reduces raw vmexit time by ~27%.
Me: fix compile warnings on i386.
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
In a lightweight exit (where we exit and reenter the guest without
scheduling or exiting to userspace in between), we don't need various
msrs on the host, and avoiding shuffling them around reduces raw exit
time by 8%.
i386 compile fix by Daniel Hecken <dh@bahntechnik.de>.
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Instructions with address size override prefix opcode 0x67
Cause the #SS fault with 0 error code in VM86 mode. Forward
them to the emulator.
Signed-Off-By: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
kunmap() expects a struct page, not a virtual address. Fixes an oops loading
kvm-intel.ko on i386 with CONFIG_HIGHMEM.
Thanks to Michael Ivanov <deruhu@peterstar.ru> for reporting.
Signed-off-by: Avi Kivity <avi@qumranet.com>
The real mode tr needs to be set to a specific tss so that I/O
instructions can function. Divert the new tr values to the real
mode save area from where they will be restored on transition to
protected mode.
This fixes some crashes on reboot when the bios accesses an I/O
instruction.
Signed-off-by: Avi Kivity <avi@qumranet.com>
If we set an msr via an ioctl() instead of by handling a guest exit, we
have the host state loaded, so reloading the msrs would clobber host
state instead of guest state.
This fixes a host oops (and loss of a cpu) on a guest reboot.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Attempting to boot the default 'bsd' kernel of OpenBSD 4.1 i386 in a guest
fails early in the kernel init inside p3_get_bus_clock while trying to read
the IA32_EBL_CR_POWERON MSR. KVM logs an 'unhandled MSR' message and the
guest kernel faults.
This patch is sufficient to allow OpenBSD to boot, after which it seems to
run fine. I'm not sure if this is the correct solution for dealing with
this particular MSR, but it works for me.
Signed-off-by: Matthew Gregan <kinetik@flim.org>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Everyone owns a piece of the exception bitmap, but they happily write to
the entire thing like there's no tomorrow. Centralize handling in
update_exception_bitmap() and have everyone call that.
Signed-off-by: Avi Kivity <avi@qumranet.com>
The lightweight vmexit path avoids saving and reloading certain host
state. However in certain cases lightweight vmexit handling can schedule()
which requires reloading the host state.
So we store the host state in the vcpu structure, and reloaded it if we
relinquish the vcpu.
Signed-off-by: Avi Kivity <avi@qumranet.com>
A typical demand page/copy on write pattern is:
- page fault on vaddr
- kvm propagates fault to guest
- guest handles fault, updates pte
- kvm traps write, clears shadow pte, resumes guest
- guest returns to userspace, re-faults on same vaddr
- kvm installs shadow pte, resumes guest
- guest continues
So, three vmexits for a single guest page fault. But if instead of clearing
the page table entry, we update to correspond to the value that the guest
has just written, we eliminate the third vmexit.
This patch does exactly that, reducing kbuild time by about 10%.
Signed-off-by: Avi Kivity <avi@qumranet.com>
When a guest writes to a page that has an mmu shadow, we have to clear
the shadow pte corresponding to the memory location touched by the guest.
Now, in nonpae mode, a single guest page may have two or four shadow
pages (because a nonpae page maps 4MB or 4GB, whereas the pae shadow maps
2MB or 1GB), so we when we look up the page we find up to three additional
aliases for the page. Since we _clear_ the shadow pte, it doesn't matter
except for a slight performance penalty, but if we want to _update_ the
shadow pte instead of clearing it, it is vital that we don't modify the
aliases.
Fortunately, exactly which page is needed (the "quadrant") is easily
computed, and is accessible in the shadow page header. All we need is
to ignore shadow pages from the wrong quadrants.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Instead of calling two functions and repeating expensive checks, call one
function and provide it with before/after information.
Signed-off-by: Avi Kivity <avi@qumranet.com>
i386 wants fs for accessing the pda even on a lightweight exit, so ensure
we can always restore it. This fixes a regression on i386 introduced by
the lightweight vmexit patch.
Signed-off-by: Avi Kivity <avi@qumranet.com>
The kvm mmu tries to detects forks by looking for repeated writes to a
page table. If it sees a fork, it unshadows the page table so the page
table copying can proceed at native speed instead of being emulated.
However, the detector also triggered on simple demand paging access patterns:
a linear walk of memory would of course cause repeated writes to the same
pagetable page, causing it to unshadow prematurely.
Fix by resetting the fork detector if we detect a demand fault.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Many msrs and the like will only be used by the host if we schedule() or
return to userspace. Therefore, we avoid saving them if we handle the
exit within the kernel, and if a reschedule is not requested.
Based on a patch from Eddie Dong <eddie.dong@intel.com> with a couple of
fixes by me.
Signed-off-by: Yaozu(Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This allows us to remove write protection earlier than otherwise. Should
some mad OS choose to use byte writes to update pagetables, it will suffer
a performance hit, but still work correctly.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Ben Dooks
David Brownell
Clifford Wolf
Kaiwan N Billimoria
Dmitry Torokhov
Maciej W. Rozycki
Akinobu Mita
Grant Likely
Vitaly Bordug
Rafael J. Wysocki
Christoph Lameter
Yoann Padioleau
Linus Torvalds
Jan Glauber
Cornelia Huck
Frank Munzert
Christian Borntraeger
Frank Pavlic
Dave Airlie
David S. Miller
Ayaz Abdulla
Jay Cliburn
jing xiang
Francois Romieu
Brice Goglin
Kumar Gala
John Donoghue
Patrice Vilchez
frederic RODO
Frank Blaschka
Thomas Klein
Jeff Garzik
Micah Gruber
S.Çağlar Onur
Andrew Morton
Jes Sorensen
Dan Aloni
Jesper Juhl
Alan Cox
Yinghai Lu
Niels de Vos
Oleg Nesterov
Robert P. J. Day
Miloslav Trmac
Dave Jones
Randy Dunlap
Adrian Bunk
Jan Engelhardt
Alexey Dobriyan
Haavard Skinnemoen
Dan Williams
Jiri Slaby
Jean Delvare
Ben Collins
Satyam Sharma
Stephen Rothwell
Thiemo Seufer
Richard Knutsson
Pavel Emelianov
Matthias Kaehlcke
Alan Cox
Zhang, Yanmin
Hugh Dickins
Neil Brown
Avi Kivity
Joerg Roedel
Shaohua Li
Luca Tettamanti
Eddie Dong
Gregory Haskins
Nitin A Kamble
Shani Moideen
Nguyen Anh Quynh
Markus Rechberger
Matthew Gregan