Currently, the i2c-algo-pca driver does nothing if the chip enters state
0x30 (Data byte in I2CDAT has been transmitted; NOT ACK has been
received). Thus, the i2c bus connected to the controller gets stuck
afterwards.
I have seen this kind of error on a custom board in certain load
situations most probably caused by interference or noise.
A possible reaction is to let the controller generate a STOP condition.
This is documented in the PCA9564 data sheet (2006-09-01) and the same
is done for other NACK states as well.
Further, state 0x38 isn't handled completely, either. Try to do another
START in this case like the data sheet says. As this couldn't be tested,
I've added a comment to try to reset the chip if the START doesn't help
as suggested by Wolfram Sang.
Signed-off-by: Enrik Berkhan <Enrik.Berkhan@ge.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When fetching DDC using i2c algo bit, we were often seeing timeouts
before getting valid EDID on a retry. The VESA spec states 2ms is the
DDC timeout, so when this translates into 1 jiffie and we are close
to the end of the time period, it could return with a timeout less than
2ms.
Change this code to use time_after instead of time_after_eq.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
with while (timeout++ < MAX_TIMEOUT); timeout reaches MAX_TIMEOUT + 1
after the loop, so the tests below are off by one.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
With `while (timeout--)' timeout reaches -1 after the loop, so the tests
below are off by one.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
While it isn't the way the standard device binding model works, it is
OK for new-style drivers to implement attach_adapter. It may help
convert the renaming legacy drivers to new style drivers faster.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Support for I2C/DDC was recently added to the tdfxfb driver, which
means that the i2c-voodoo3 driver can be deprecated.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
A recent change broke debugging of pca_xfer(), fix it.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
'disable_delay' was static which is wrong as it is calculated using the per-device
bus speed. This patch turns 'disable_delay' into a per-device variable.
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Support for the s6000 on-chip i2c controller.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch makes the I2C bus speed configurable by using the I2C node
property "clock-frequency". If the property is not defined, the old
fixed clock settings will be used for backward comptibility.
The generic I2C clock properties, especially the CPU-specific source
clock pre-scaler are defined via the OF match table:
static const struct of_device_id mpc_i2c_of_match[] = {
...
{.compatible = "fsl,mpc8543-i2c",
.data = &(struct fsl_i2c_match_data) {
.setclock = mpc_i2c_setclock_8xxx,
.prescaler = 2,
},
},
The "data" field defines the relevant I2C setclock function and the
relevant pre-scaler for the I2C source clock frequency.
It uses arch-specific tables and functions to determine resonable
Freqency Divider Register (fdr) values for MPC83xx, MPC85xx, MPC86xx,
MPC5200 and MPC5200B.
The i2c->flags field and the corresponding FSL_I2C_DEV_* definitions
have been removed as they are obsolete.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch used the dev_dbg, dev_err, etc. functions for debug
and error output instead of printk and pr_debug.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix errors reported by checkpatch (indention, long lines, trailing
white space, etc.).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
[ben-linux@fluff.org: fix minor patch fault in remove]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is required in order to ensure that core system devices such as
voltage regulators attached via I2C are avaiable early in boot.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The platform data for the i2c-s3c2410 driver used to allow a min,
max and desired frequency for the I2C bus. This patch reduces it
to simply a desired frequency ceiling and corrects all the uses
of the platform data appropriately.
This means, for example, that on a system with a 66MHz fclk, a
request for 100KHz will achieve 65KHz which is safe and
acceptable, rather than 378KHz which it would have achieved
without this change.
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
[ben-linux@fluff.org: tidy subject and description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The sda_delay field should be specified in ns, not in clock ticks
as when using cpufreq we could be changing the bus rate.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Implementation of I2C Adapter/Algorithm Driver for I2C Bus integrated
in Freescale's i.MX/MXC processors.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (fschmd) Add support for the FSC Hades IC
hwmon: (fschmd) Add support for the FSC Syleus IC
i2c-i801: Instantiate FSC hardware montioring chips
dmi: Let dmi_walk() users pass private data
hwmon: Define a standard interface for chassis intrusion detection
Move the pcf8591 driver to hwmon
hwmon: (w83627ehf) Only expose in6 or temp3 on the W83667HG
hwmon: (w83627ehf) Add support for W83667HG
hwmon: (w83627ehf) Invert fan pin variables logic
hwmon: (hdaps) Fix Thinkpad X41 axis inversion
hwmon: (hdaps) Allow inversion of separate axis
hwmon: (ds1621) Clean up documentation
hwmon: (ds1621) Avoid unneeded register access
hwmon: (ds1621) Clean up register access
hwmon: (ds1621) Reorder code statements
Detect various FSC hwmon IC's based on DMI tables and then let
the i2c-i801 driver instantiate the i2c client devices. Note that
some of the info in the added table is indentical for all rows, still
this is kept in the table to keep the code general and thus (hopefully)
easily extensible in the future.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Directory drivers/i2c/chips is going away, so drivers there must find
new homes. For the pcf8591 driver, the best choice seems to be the
hwmon subsystem. While the Philips PCF8591 device isn't a typical
hardware monitoring chip, its DAC interface is compatible with the
hwmon one, so it fits somewhat.
If a better subsystem is ever created for ADC/DAC chips, the driver
could be moved there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c-core: Some style cleanups
i2c-piix4: Add support for the Broadcom HT1100 chipset
i2c-piix4: Add support to SB800 SMBus changes
i2c-pca-platform: Use defaults if no platform_data given
i2c-algo-pca: Use timeout for checking the state machine
i2c-algo-pca: Rework waiting for a free bus
i2c-algo-pca: Add PCA9665 support
i2c: Adapt debug macros for KERN_* constants
i2c-davinci: Fix timeout handling
i2c: Adapter timeout is in jiffies
i2c: Set a default timeout value for all adapters
i2c: Add missing KERN_* constants to printks
i2c-algo-pcf: Handle timeout correctly
i2c-algo-pcf: Style cleanups
eeprom/at24: Remove EXPERIMENTAL
i2c-nforce2: Add support for MCP67, MCP73, MCP78S and MCP79
i2c: Clarify which clients are auto-removed
i2c: Let checkpatch shout on users of the legacy model
i2c: Document the different ways to instantiate i2c devices
Some lines over 80.
The printk(KERN_ERR ... ) should be dev_err.
And some blankspace should be deleted.
Signed-off-by: Zhenwen Xu <helight.xu@gmail.com>
Signed-off-by: Jean Delvare <khlai@linux-fr.org>
Add support for the Broadcom HT1100 LD chipset (SMBus function.)
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the AMD SB800 Family series of products.
Major changes include the changes to addressing the SMBus registers at different
location from the locations in the previous compatible parts from AMD such as
SB400/SB600/SB700. For SB800, the main features and register definitions of
SMBus and other interfaces are still compatible with the previous products with
the only change being in how to access the internal registers for these blocks.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We now timeout also if the state machine does not change within the
given time. For that, the driver-specific completion-functions are
extended to return true or false depending on the timeout. This then
gets checked in the algorithm.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Waiting for a free bus now accepts the timeout value in jiffies and does
proper checking using time_before.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the changes to the debug macros in the i2c subsystem
to meet this requirement. Also changing no-debug statements
to raw printks again.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Properly set the adapter timeout value in jiffies, and then use that
value in the driver, rather than a hard-coded constant.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Kevin Hilman <khilman@mvista.com>
i2c_adapter.timeout is in jiffies. Fix all drivers which thought
otherwise. It didn't really matter as long as the value was only used
inside the driver, but soon i2c-core will use it too so it must have
the proper unit.
Note: for the i2c-mpc driver, this fixes a bug in polling mode.
Timeout would trigger after 1 jiffy, which is most probably not what
the author wanted.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Clifford Wolf <clifford@clifford.at>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Setting a default timeout value on a per-algo basis doesn't make any
sense. Move the default value setting to i2c-core. Individual adapter
drivers can specify a different (non-zero) value if they wish.
Also express the timeout value in a way which results in the same
duration regarless of the value of HZ.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the missing pieces here for the i2c subsystem.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
With a postfix decrement these timeouts reach -1 rather than 0, but after the
loop it is tested whether they have become 0.
As pointed out by Jean Delvare, the msg_num should be tested before the timeout.
With the current order, you could exit with a timeout error while all the
messages were successfully transferred.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Eric Brower <ebrower@gmail.com>
The MCP78S and MCP79 appear to be compatible with the previous nForce
chips as far as the SMBus controller is concerned. The MCP67 and MCP73
were not tested yet but I'd be very surprised if they weren't
compatible too.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Oleg Ryjkov <olegr@olegr.ca>
Cc: Malcolm Lalkaka <mlalkaka@gmail.com>
Cc: Zbigniew Luszpinski <zbiggy@o2.pl>
The automatic removal of i2c clients only affects the clients which
were created automatically in the first place. Add a comment saying
that to avoid any confusion.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch implements uevent suppress in kobject and removes it
from struct device, based on the following ideas:
1,Uevent sending should be one attribute of kobject, so suppressing it
in kobject layer is more natural than in device layer. By this way,
we can do it for other objects embedded with kobject.
2,It may save several bytes for each instance of struct device.(On my
omap3(32bit ARM) based box, can save 8bytes per device object)
This patch also introduces dev_set|get_uevent_suppress() helpers to
set and query uevent_suppress attribute in case to help kobject
as private part of struct device in future.
[This version is against the latest driver-core patch set of Greg,please
ignore the last version.]
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The i2c_wait() function is using wait_event_interruptible_timeout() to wait for
the I2C controller to signal that it has completed an I2C bus operation. If
the process that causes the I2C operation terminated abruptly, the wait will
be interrupted, returning an error. It is better to let the I2C operation
finished before the process exits.
It is safe to use wait_event_timeout() instead, because the timeout will allow
the process to exit if the I2C bus hangs. It's also better to allow the
I2C operation to finish, because unacknowledged I2C operations can cause the
I2C bus to hang.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
`iop_adma_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv_xor_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_unmap_regs' referenced in section `.devinit.text' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`orion_nand_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`pxafb_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the necessary i2c_board_info structure to fix the lack of PCF8583
RTC on RiscPC.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
i2c_algo_bit_data.timeout is supposed to be in jiffies, so drivers
should use set this value in terms of HZ.
Ultimately I think this field should be discarded in favor of
i2c_adapter.timeout, but that's left for a future patch.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
The unit in which user-space can set the bus timeout value is jiffies
for historical reasons (back when HZ was always 100.) This is however
not good because user-space doesn't know how long a jiffy lasts. The
timeout value should instead be set in a fixed time unit. Given the
original value of HZ, this unit should be 10 ms, for compatibility.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
With a postfix decrement these timeouts reach -1 rather than 0, but
after the loop it is tested whether they have become 0.
As pointed out by Jean Delvare, the condition we are waiting for should
also be tested before the timeout. With the current order, you could
exit with a timeout error while the job is actually done.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If dev->id is not -1, the platform code may use static bus numbering
rather than dynamic. The patch also changes the i2c_versatile_init to a
subsys_initcall rather than module_init to make sure it is initialised
before the I2C devices initialisation.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
By providing a dummy ick for OMAP1510 and OMAP310, we avoid having
SoC conditional clock information in i2c-omap.c. Also, fix the
error handling by making sure we propagate the error returned via
clk_get().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On OMAP1, the I2C functional clock (fck) is the armxor_ck, so there's
no need to get "armxor_ck" separately.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update Kconfig text to specify this driver as I2C.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As drivers/i2c/chips is going to go away, move the driver to
drivers/misc/eeprom. Other eeprom drivers may be moved here later, too.
Update Kconfig text to specify this driver as I2C.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch is used to help Jean Delvare to get rid of drivers/i2c/chips/
directory. The new location suggested by Kumar Gala: as the driver is
83xx specific it's placed into arch/powerpc/platforms/83xx/.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (123 commits)
wimax/i2400m: add CREDITS and MAINTAINERS entries
wimax: export linux/wimax.h and linux/wimax/i2400m.h with headers_install
i2400m: Makefile and Kconfig
i2400m/SDIO: TX and RX path backends
i2400m/SDIO: firmware upload backend
i2400m/SDIO: probe/disconnect, dev init/shutdown and reset backends
i2400m/SDIO: header for the SDIO subdriver
i2400m/USB: TX and RX path backends
i2400m/USB: firmware upload backend
i2400m/USB: probe/disconnect, dev init/shutdown and reset backends
i2400m/USB: header for the USB bus driver
i2400m: debugfs controls
i2400m: various functions for device management
i2400m: RX and TX data/control paths
i2400m: firmware loading and bootrom initialization
i2400m: linkage to the networking stack
i2400m: Generic probe/disconnect, reset and message passing
i2400m: host/device procotol and core driver definitions
i2400m: documentation and instructions for usage
wimax: Makefile, Kconfig and docbook linkage for the stack
...
This moves the isp1301-omap driver from the drivers/i2c/chips
directory (which will be shrinking) into a new drivers/usb/otg
directory (which will grow, with more drivers and utilities).
Note that OTG infrastructure needs to be initialized before
either host or peripheral side USB support, and may be needed
before for pure host or pure peripheral configurations.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert the apanel driver to the new i2c device driver binding model,
as the legacy model is going away soon. In the new model, the apanel
driver is no longer scanning all the i2c adapters, instead the
relevant bus driver (i2c-i801) is instantiating the device as needed.
One side benefit is that the apanel driver will now load automatically
on all systems where it is needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
I2C_CLASS_ALL is almost never what bus driver authors really want.
These i2c classes are really only about which devices must be probed,
not what devices can be present. As device drivers get converted to the
new i2c device driver model, only a few device types will keep relying
on probing.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Use dev_name(dev) instead of accessing dev.bus_id directly, as the
latter is going away soon.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
We want to submit a patch to -next, which will remove bus_id from
"struct device", to find the remaining pieces to convert, and finally
switch over to the new api, which will remove the 20 bytes array
and does no longer have a size limitation.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'i2c-next' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-omap: fix type of irq handler function
i2c-s3c2410: Change IRQ to be plain integer.
i2c-s3c2410: Allow more than one i2c-s3c2410 adapter
i2c-s3c2410: Remove default platform data.
i2c-s3c2410: Use platform data for gpio configuration
i2c-s3c2410: Fixup style problems from checkpatch.pl
i2c-omap: Enable I2C wakeups for 34xx
i2c-omap: reprogram OCP_SYSCONFIG register after reset
i2c-omap: convert 'rev1' flag to generic 'rev' u8
i2c-omap: fix I2C timeouts due to recursive omap_i2c_{un,}idle()
i2c-omap: Clean-up i2c-omap
i2c-omap: Don't compile in OMAP15xx I2C ISR for non-OMAP15xx builds
i2c-omap: Mark init-only functions as __init
i2c-omap: Add support for omap34xx
i2c-omap: FIFO handling support and broken hw workaround for i2c-omap
i2c-omap: Add high-speed support to omap-i2c
i2c-omap: Close suspected race between omap_i2c_idle() and omap_i2c_isr()
i2c-omap: Do not use interruptible wait call in omap_i2c_xfer_msg
Fix up apparently-trivial conflict in drivers/i2c/busses/i2c-s3c2410.c
ove the menelaus driver from drivers/i2c/chips to drivers/mfd
since it's more of a multi-function device than anything else,
and since Jean is trying to vanish drivers/i2c/chips ASAP.
One way to think of these chips are as the PMIC family most
used with OMAP2 generation chips.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Move the tps65010 driver from drivers/i2c/chips to drivers/mfd
since it's more of a multi-function device than anything else,
and since Jean is trying to vanish drivers/i2c/chips ASAP.
One way to think of these chips are as the PMIC family most
used with OMAP1 generation chips.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (407 commits)
[ARM] pxafb: add support for overlay1 and overlay2 as framebuffer devices
[ARM] pxafb: cleanup of the timing checking code
[ARM] pxafb: cleanup of the color format manipulation code
[ARM] pxafb: add palette format support for LCCR4_PAL_FOR_3
[ARM] pxafb: add support for FBIOPAN_DISPLAY by dma braching
[ARM] pxafb: allow pxafb_set_par() to start from arbitrary yoffset
[ARM] pxafb: allow video memory size to be configurable
[ARM] pxa: add document on the MFP design and how to use it
[ARM] sa1100_wdt: don't assume CLOCK_TICK_RATE to be a constant
[ARM] rtc-sa1100: don't assume CLOCK_TICK_RATE to be a constant
[ARM] pxa/tavorevb: update board support (smartpanel LCD + keypad)
[ARM] pxa: Update eseries defconfig
[ARM] 5352/1: add w90p910-plat config file
[ARM] s3c: S3C options should depend on PLAT_S3C
[ARM] mv78xx0: implement GPIO and GPIO interrupt support
[ARM] Kirkwood: implement GPIO and GPIO interrupt support
[ARM] Orion: share GPIO IRQ handling code
[ARM] Orion: share GPIO handling code
[ARM] s3c: define __io using the typesafe version
[ARM] S3C64XX: Ensure CPU_V6 is selected
...
Add clock framework support to the sh_mobile i2c driver and
adjust the processor specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The probe function used a pointer to the interrupt
handler to register as a 'void *', change it to the
proper type of irq_handler_t.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change the code to use a plain integer as the holder
for the IRQ for the device and use platform_get_irq()
to find it.
This makes the code slightly neater, and easier to get
the IRQ number.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Newer SoCs such as the S3C6410 have 2 instances of this i2c
controller block in and thus require the ability to create
two seperate busses from this.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The platform data should now always be present when the device
is initialised, so we can remove the default platform data in
the driver.
All the device initialisation points in the board specific code
should already have been changed to initialise this as necessary.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add a callback to set the gpio configuration for the
i2c device instead of a set include. This also allows
the remvoal of the machine gpio and hardware files.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fixup the 36 warnings and errors generated from running
checkpatch.pl on the driver. The warnings are too numerous
to be listed here.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
As noted by Julia Lawall <julia@diku.dk>, we can never
trigger the check for being in suspend due to the result
of !readl(i2c->regs + S3C2410_IICCON) & S3C2410_IICCON_IRQEN
always being 0.
Add suspend/resume hooks to stop i2c transactions happening
until the driver has been resumed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make the driver report an ENXIO error immediately upon NAK instead of
waiting for another interrupt and getting a timeout.
When reading from a device that is not present or declines to respond
to, e.g., a non-existent register address, CPM immediately reports a
NAK condition in the TxBD, but the driver kept waiting until a timeout,
which takes 1 second and causes an ugly console error message.
Signed-off-by: Mike Ditto <mditto@consentry.com>
Acked-by: Jochen Friedrich <jochen@scram.de>
[ben-linux@fluff.org: reordered description text]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
tmp is used as host-endian and is loaded from a be64, fix the cast and the
endian accessor used.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c clients should be removed in reverse order compared to the probe
(actually: bind) order. This matters when several clients depend on
each other.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Build fixes for isp1301_omap; no behavior changes:
- fix incorrect probe() signature (it changed many months ago)
- provide missing functions on H3 and H4 boards
- "sparse" fixes (static, NULL-vs-0)
The H3 build bits subset some of the stuff that was previously in
the OMAP tree but never went to mainline.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Where devices only have one consumer, passing a consumer clock ID
has no real benefit. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I2C_WE registers were not configured, which caused huge delays in
I2C operations while cpu idle was enabled and omap entered WFI.
This patch enables all I2C wakeup sources.
Signed-off-by: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The I2C controller clears its OCP_SYSCONFIG register after an OCP soft reset.
Reprogram OCP_SYSCONFIG for maximum power savings on rev3.6 controllers
and beyond. On 2430, this involves setting the module AUTOIDLE bit.
On 3430, this includes module AUTOIDLE, wakeup enable, slave smart-idle,
and considers only the module functional clock state for idle-ack.
Boot-tested on 2430SDP and 3430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
i2c-omap discriminates only between "revision 1" or "greater than
revision 1." A following patch introduces code that must also
discriminate between rev2.x, rev3.6, and rev3.12 controllers. Support
this by storing the full revision data from the I2C_REV register, rather
than just a single bit.
The revision definitions may need to be extended for other ES levels
that aren't currently available here. rev3.6 is what's present on the
2430SDP here (unknown ES revision); rev3.12 is used on the 3430ES2
here.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_i2c_unidle() and omap_i2c_idle() are called recursively during
omap_i2c_probe(). This is evidently unexpected and will wipe
out the I2C interrupt enable register the second time that
omap_i2c_idle() is called consecutively. Any I2C transactions
following a probe of a bus with at least one device on it will then
time out.
Fix by moving omap_i2c_idle() further up in omap_i2c_probe(). Ensure
the I2C controller is marked as idle before the probe starts. Also
attempt to catch future reappearances of this bug early in development
by warning in omap_i2c_{un,}idle() when they are called recursively.
Problem reported by David Brownell <david-b@pacbell.net>.
Tested on 3430SDP and 2430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Acked-by; Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Skip compiling OMAP15xx I2C ISR for non-OMAP15xx builds. Saves 400 bytes
of text for most OMAP builds.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on an earlier patch from Nishant Menon:
- Transfers can use FIFO on FIFO capable devices
- Prevents errors for HSI2C if FIFO is not used
- Implemented errenous handling of STT-STP handling on SDP2430
Also merged in is a fix from Jaron Marini to fix occasional i2c
hang if OMAP_I2C_CON_STT remains asserted.
Signed-off-by: Jason P Marini <jason.marini@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Omap2430 has additional support for high-speed I2C.
This patch moves I2C speed parameter (from module) to platform data.
Also added basic High Speed support based on I2C bus speed.
This patch is tested for high speed I2C (with TWL4030 Keypad) and works as
expected.
Also change the 2430 i2chs_fck names to use the standard naming.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_i2c_idle() sets an internal flag, "dev->idle", instructing its
ISR to decline interrupts. It sets this flag before it actually masks
the interrupts on the I2C controller. This is problematic, since an
I2C interrupt could arrive after dev->idle is set, but before the
interrupt source is masked. When this happens, Linux disables the I2C
controller's IRQ, causing all future transactions on the bus to fail.
Symptoms, happening on about 7% of boots:
irq 56: nobody cared (try booting with the "irqpoll" option)
<warning traceback here>
Disabling IRQ #56
i2c_omap i2c_omap.1: controller timed out
In omap_i2c_idle(), this patch sets dev->idle only after the interrupt
mask write to the I2C controller has left the ARM write buffer.
That's probably the major offender. For additional prophylaxis, in
omap_i2c_unidle(), the patch clears the dev->idle flag before
interrupts are enabled, rather than afterwards.
The patch has survived twenty-two reboots on the 3430SDP here without
wedging I2C1. Not absolutely dispositive, but promising!
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If there is a signal pending and wait_for_completion_interruptible_timeout
terminates with -ERESTARTSYS, we return and disable the i2c clocks in
omap_i2c_xfer.
If we terminate before sending last i2c message with a stop condition, the
bus remains busy and we are not able to send new messages into bus with
successive omap_i2c_xfer calls. Therefore a pending signal is not caught
here and we return only because of timeout or i2c error.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In commit e6bafba5b4, a bug was fixed that
involved converting !x & y to !(x & y). The code below shows the same
pattern, and thus should perhaps be fixed in the same way. In particular,
the result of !readl(i2c->regs + S3C2410_IICCON) & S3C2410_IICCON_IRQEN is
always 0.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ expression E; constant C; @@
(
!E & !C
|
- !E & C
+ !(E & C)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The scx200_i2c driver is missing the .class parameter, which means no
i2c drivers are willing to probe for devices on the bus and attach to
them.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Add info->archdata field
i2c: Inform about deprecated chips directory
i2c: Use pci_ioremap_bar()
Schedule removal of the legacy i2c device driver binding model
i2c: Clean up <linux/i2c.h>
i2c: Update and clean up writing-clients document
i2c: Drop 2-byte address block transfer defines
i2c: Delete legacy model documentation
i2c: Constify i2c_get_clientdata's parameter
i2c: Delete outdated client porting guide
i2c: Make clear what the class field of i2c_adapter is good for
i2c-algo-pcf: Fix typo in debugging log message
i2c-algo-pcf: Add adapter hooks around xfer begin and end
i2c-algo-pcf: Pass adapter data into ->waitforpin() method
i2c-i801: Add support for Intel Ibex Peak
If present the info->archdata is copied into the dev->archdata.
Some (OpenFirmware) platforms need it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The chips directory under drivers/i2c is deprecated. Spread the word!
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use the newly introduced pci_ioremap_bar() function in drivers/i2c.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix typo in debugging log message.
deteted --> detected
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Some I2C bus implementations need to synchronize with external
entities, such as system firmware, which might also be programming the
same I2C bus.
In order to facilitate this add ->xfer_begin() and ->xfer_end() hooks
which are invoked around pcf_xfer().
[JD: Make these hooks optional.]
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Similar to commit 618b26d528, also remove
automatic probing for this i2c controller. Might need updates to dts files
using it.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Only accept dynids whose driver_data value matches one of the driver's
pci_driver_id entries. This prevents the user from accidentally passing
values the drivers do not expect.
Cc: Milton Miller <miltonm@bga.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The driver flag dynids.use_driver_data is almost consistently not set,
and causes more problems than it solves. It was initially intended as a
flag to indicate whether a driver's usage of driver_data had been
carefully inspected and was ready for values from userspace. That audit
was never done, so most drivers just get a 0 for driver_data when new
IDs are added from userspace via sysfs. So remove the flag, allowing
drivers to see the data directly (a followon patch validates the passed
driver_data value against what the drivers expect).
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tejun's commit 7b595756ec made sysfs
attribute->owner unnecessary. But the field was left in the structure to
ease the merge. It's been over a year since that change and it is now
time to start killing attribute->owner along with its users - one arch at
a time!
This patch is attempt #1 to get rid of attribute->owner only for
CONFIG_X86_64 or CONFIG_X86_32 . We will deal with other arches later on
as and when possible - avr32 will be the next since that is something I
can test. Compile (make allyesconfig / make allmodconfig / custom config)
and boot tested.
akpm: the idea is that we put the declaration of sttribute.owner inside
`#ifndef CONFIG_X86'. But that proved to be too ambitious for now because
new usages kept on turning up in subsystem trees.
[akpm: remove the ifdef for now]
Signed-off-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change i2c to use the new bcd2bin/bin2bcd functions instead of the
obsolete BCD2BIN/BIN2BCD macros.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The legacy i2c binding model is phasing out, so the ams driver needs
to be converted to a new-style i2c driver. Here is a naive approach of
this conversion. Basically it is moving the i2c device creation from
the ams driver to the i2c-powermac driver. This should work, but I
suspect we could come up with something cleaner by declaring the i2c
device as part of the platform setup. This could be done later by
someone more familiar with openfirmware-based platforms than I am
myself.
One nice thing brought by this conversion is that the ams driver
should be loaded automatically on systems where is is needed (at
least when the I2C interface to the chip is used) providing
coldplug-aware user-space environment.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Stelian Pop <stelian@popies.net>
Cc: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (46 commits)
UIO: Fix mapping of logical and virtual memory
UIO: add automata sercos3 pci card support
UIO: Change driver name of uio_pdrv
UIO: Add alignment warnings for uio-mem
Driver core: add bus_sort_breadthfirst() function
NET: convert the phy_device file to use bus_find_device_by_name
kobject: Cleanup kobject_rename and !CONFIG_SYSFS
kobject: Fix kobject_rename and !CONFIG_SYSFS
sysfs: Make dir and name args to sysfs_notify() const
platform: add new device registration helper
sysfs: use ilookup5() instead of ilookup5_nowait()
PNP: create device attributes via default device attributes
Driver core: make bus_find_device_by_name() more robust
usb: turn dev_warn+WARN_ON combos into dev_WARN
debug: use dev_WARN() rather than WARN_ON() in device_pm_add()
debug: Introduce a dev_WARN() function
sysfs: fix deadlock
device model: Do a quickcheck for driver binding before doing an expensive check
Driver core: Fix cleanup in device_create_vargs().
Driver core: Clarify device cleanup.
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (158 commits)
powerpc: Fix CHRP PCI config access for indirect_pci
powerpc/chrp: Fix detection of Python PCI host bridge on IBM CHRPs
powerpc: Fix 32-bit SMP boot on CHRP
powerpc: Fix link errors on 32-bit machines using legacy DMA
powerpc/pci: Improve detection of unassigned bridge resources
hvc_console: Fix free_irq in spinlocked section
powerpc: Get USE_STRICT_MM_TYPECHECKS working again
powerpc: Reflect the used arguments in machine_init() prototype
powerpc: Fix DMA offset for non-coherent DMA
powerpc: fix fsl_upm nand driver modular build
powerpc/83xx: add NAND support for the MPC8360E-RDK boards
powerpc: FPGA support for GE Fanuc SBC610
i2c: MPC8349E-mITX Power Management and GPIO expander driver
powerpc: reserve two DMA channels for audio in MPC8610 HPCD device tree
powerpc: document the "fsl,ssi-dma-channel" compatible property
powerpc: disable CHRP and PMAC support in various defconfigs
OF: add fsl,mcu-mpc8349emitx to the exception list
powerpc/83xx: add DS1374 RTC support for the MPC837xE-MDS boards
powerpc: remove support for bootmem-allocated memory for the DIU driver
powerpc: remove non-dependent load fsl_booke PTE_64BIT
...
Add support for SMBus Process Call transactions. These are combined
word write, word read transactions.
Signed-off-by: Prakash Mortha <pmortha@escient.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Restore the i2c_smbus_process_call() as one driver (for the
Micronas MAP5401) will need it soon.
[JD: Update documentation accordingly.]
Signed-off-by: Prakash Mortha <pmortha@escient.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move I2C driver model init earlier in the boot sequence.
This avoids oopsing in statically linked systems when some
subsystems register I2C drivers in subsys_initcall() code,
but those subsystems are linked (and initialized) before I2C.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The two Tyan SMBus mux drivers (i2c-amd756-s4882 and i2c-nforce2-s4985)
are only useful on specific x86 motherboards, so there is no point in
letting them be built on other architectures.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Guard I2C against oopsing because of init sequence problems, by
verifying that i2c_init() has been called before calling any
routines that rely on that initialization. This specific test
just requires that bus_register(&i2c_bus_type) was called.
Examples of this kind of oopsing come from subystems and drivers
which register I2C drivers in their subsys_initcall code but
which are statically linked before I2C by drivers/Makefile.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The i2c-parport-light driver isn't a real platform driver, so it
should not instantiate platform devices with resources. The resource
management system can't cope with colliding resources, and we are
likely to create such a colliding resource.
So, better just try to grab the I/O ports we need right at module
initialization time, and bail out if we can't. It has the added
benefit that the module will no longer load if it isn't going to work,
which is definitely more user-friendly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
All the tps6501{0,1,2,3,4} chips have a signal for hooking up with
a vibrator (for non-auditory cell phone "ring") ... expose that as
one more (output-only) GPIO.
[ dbrownell@users.sourceforge.net: comments; list tps65014 too ]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Thanks to new datasheets published on http://linux.via.com.tw we can now add
support for VX800/VX820 chipsets.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This adds support for the SMBus adapter found in the various FPGAs on
the Renesas Highlander platforms. Particularly the R0P7780LC0011RL and
R0P7785LC0011RL FPGAs.
Functionality is fairly restricted, in that only byte and block data
transfers are supported. Normal/fast mode and IRQ/polling are also
supported. Primarily used for various RTCs and thermal sensors.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Grabbing ISA bus resources without anything or anyone telling us we
should can break boot on randconfig/allyesconfig builds by keeping
resources that are in fact owned by different hardware busy and does
as reported by Ingo Molnar.
Generally it's also dangerous to just poke at random I/O ports and
especially those in the range where other old easily confused ISA
hardware might live.
For this specialized I2C bus driver, insist that the user specifies
the resources before grabbing them.
The^WA user of this driver is a one time
echo "options i2c-pca-isa base=0x330 irq=10" >> /etc/modprobe.conf
away from the old behaviour.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Based on David Brownell's patch for tps65010 and previous work by
Felipe Balbi, this patch finishes converting isp1301_omap to a
new-style i2c driver.
There's definitely room for further drivers cleanups, but these are
out of the scope of this patch.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Based on David Brownell's patch for tps65010, this patch
starts converting isp1301_omap.c to new-style i2c driver.
Signed-off-by: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Tony Lindgren <tony@atomide.com>
On MPC8349E-mITX, MPC8315E-RDB and MPC837x-RDB boards there is a
Freescale MC9S08QG8 (MCU) chip with the custom firmware
pre-programmed. The chip is used to power-off the board by the
software, and to control some GPIO pins.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
This patch suppresses I2C device probing by clearing the class field
of the "struct i2c_adapter" for the MPC I2C bus adapters. Some board
configurations which rely on probing must be fixed up by adding a
proper I2C device node to the DTS file, like the TQM85xx modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add fast_mode option to i2c_pxa_platform_data and use it to set the
ICR_FM bit appropriately when i2c_pxa_reset is called. Parameter
called fast_mode rather than frequency as this driver is also used
for the i2c_pxa_pwr bus which has different normal and fast frequencies.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need to convert the error pointer from class_create(), else we'll return the
successful return code from register_chrdev() on failure.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
__devexit for i2c_powermac_probe is obviously wrong. In the definition
of struct platform_driver i2c_powermac_driver the remove function
i2c_powermac_remove is wrapped in __devexit_p, so it should be defined
using __devexit.
Signed-off-by: Uwe Kleine-Koenig <ukleinek@informatik.uni-freiburg.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Now that arch/ppc is dead CONFIG_PPC_MERGE is always defined for all
powerpc platforms and we want to get rid of CONFIG_PPC_MERGE use
CONFIG_PPC instead.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Properly hook the I2C driver into the PM code; the previous fix for
this (ece5f7b3c4) worked around the
platform where I2C is required to be available early during resume.
It has been found to be sufficient to use the early resume hook for
this function, so the original hack can die. Leave the hack in
place for the PIO transfer handler though.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
i2c_pxa_abort can be called from the atomic context.
Change it to use mdelay and counted loop.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add power I2C support for PXA3xx processors
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch teaches the i2c-sh_mobile driver to make use of wait irqs.
Without this patch only dte irqs are used which may lead to overruns
and cases of missing stop and extra bytes being read on the i2c bus.
Use of wait irqs forces the hardware to pause and wait until the cpu
is ready. Polling is also reworked in this patch to fix ms delay issues.
Verified with bus analyzer and tested on MigoR and AP325RXA boards.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some DVB adapters do not support the special I2C transaction that we
use for probing purposes. There's no point in logging this event, as
there's nothing the user can do and in general there is no actual
problem. So, degrade one of these messages to a debug message, and
move the other one around so that it is only printed on bogus drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Uwe Bugla <uwe.bugla@gmx.de>
device_init_wakeup must be called after device_register.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix various printk format strings where %zd was passed a size_t;
those should be %zu instead. (Courtesy of a version of GCC which
warns when these details are wrong.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We check for address business in i2c_probe_address(),
i2c_detect_address() and i2c_new_probed_device(), but this isn't
sufficient. Drivers can call i2c_attach_client() and
i2c_new_device() on any address, so we must check the address there
as well.
This fixes bug #11239:
http://bugzilla.kernel.org/show_bug.cgi?id=11239
Signed-off-by: Jean Delvare <khali@linux-fr.org>
In kernel 2.6.26, the ability to select I2C algorithm drivers manually
was removed, as all in-kernel drivers do that automatically. However
there were some complaints that it was a problem for out-of-tree I2C
bus drivers. In order to address these complaints, let's allow manual
selection of these drivers again, but still hide them by default for
better general user experience.
This closes bug #11140:
http://bugzilla.kernel.org/show_bug.cgi?id=11140
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix a NULL pointer dereference that happened when calling
i2c_new_probed_device on one of the addresses for which we use byte
reads instead of quick write for detection purpose (that is: 0x30-0x37
and 0x50-0x5f).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The two I2C bus multiplexer drivers (i2c-amd756-s4882 and
i2c-nforce2-s4985) make use of the bus they want to multiplex before
checking if it is really present. Swap the instructions to test for
presence first. This fixes a oops reported by Ingo Molnar.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ingo Molnar <mingo@elte.hu>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are 43 includes of asm/mach-types.h by files that don't
reference anything from that file. Remove these unnecessary
includes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PM_SUSPEND_MEM: Blackfin does not maintain register state through
Hibernate. Save and restore peripheral base initialization during
PM transitions.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change the i2c_gpio driver to use platform_driver_register()
instead of platform_driver_probe() to ensure that is can
attach to any devices that may be loaded after it has initialised.
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Allow the platform data to specify the bus bumber that the
new I2C bus will be given. This is to allow the use of the
board registration mechanism to specify the new style of
I2C device registration which allows boards to provide a
list of attached devices.
Note, as discussed on the mailing list, we have dropped
backwards compatibility of adding an dynamic bus number
as it should not affect most boards to have the bus pinned
to 0 if they have either not specified platform data for
driver. Any board supplying platform data will automatically
have the bus_num field set to 0, and anyone who needs the
driver on a different bus number can supply platform data
to set bus_num.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds functionality to the gpio-lib subsystem to make it
possible to enable the gpio-lib code even if the architecture code didn't
request to get it built in.
The archtitecture code does still need to implement the gpiolib accessor
functions in its asm/gpio.h file. This patch adds the implementations for
x86 and PPC.
With these changes it is possible to run generic GPIO expansion cards on
every architecture that implements the trivial wrapper functions. Support
for more architectures can easily be added.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a simple sysfs interface for GPIOs.
/sys/class/gpio
/export ... asks the kernel to export a GPIO to userspace
/unexport ... to return a GPIO to the kernel
/gpioN ... for each exported GPIO #N
/value ... always readable, writes fail for input GPIOs
/direction ... r/w as: in, out (default low); write high, low
/gpiochipN ... for each gpiochip; #N is its first GPIO
/base ... (r/o) same as N
/label ... (r/o) descriptive, not necessarily unique
/ngpio ... (r/o) number of GPIOs; numbered N .. N+(ngpio - 1)
GPIOs claimed by kernel code may be exported by its owner using a new
gpio_export() call, which should be most useful for driver debugging.
Such exports may optionally be done without a "direction" attribute.
Userspace may ask to take over a GPIO by writing to a sysfs control file,
helping to cope with incomplete board support or other "one-off"
requirements that don't merit full kernel support:
echo 23 > /sys/class/gpio/export
... will gpio_request(23, "sysfs") and gpio_export(23);
use /sys/class/gpio/gpio-23/direction to (re)configure it,
when that GPIO can be used as both input and output.
echo 23 > /sys/class/gpio/unexport
... will gpio_free(23), when it was exported as above
The extra D-space footprint is a few hundred bytes, except for the sysfs
resources associated with each exported GPIO. The additional I-space
footprint is about two thirds of the current size of gpiolib (!). Since
no /dev node creation is involved, no "udev" support is needed.
Related changes:
* This adds a device pointer to "struct gpio_chip". When GPIO
providers initialize that, sysfs gpio class devices become children of
that device instead of being "virtual" devices.
* The (few) gpio_chip providers which have such a device node have
been updated.
* Some gpio_chip drivers also needed to update their module "owner"
field ... for which missing kerneldoc was added.
* Some gpio_chips don't support input GPIOs. Those GPIOs are now
flagged appropriately when the chip is registered.
Based on previous patches, and discussion both on and off LKML.
A Documentation/ABI/testing/sysfs-gpio update is ready to submit once this
merges to mainline.
[akpm@linux-foundation.org: a few maintenance build fixes]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This mirrors the functionality that driver_for_each_device has as well.
We add a start variable, and all callers of the function are fixed up at
the same time.
The block layer will be using this new functionality in a follow-on
patch.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new-style max6875 driver implements the optional detect() callback
to cover the use cases of the legacy driver. I'm curious if anyone
really needs this though, so it might be removed in the feature.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style pca9539 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Warning: users will now have to use the force module parameter to get
the driver to attach to their device. That's not a bad thing as these
devices can't be detected anyway.
Note that this doesn't change the fact that this driver is deprecated
in favor of gpio/pca953x.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style pcf8575 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Warning: users will now have to use the force module parameter to get
the driver to attach to their device. That's not a bad thing as these
devices can't be detected anyway.
Note that this doesn't change the fact that this driver is deprecated
in favor of gpio/pcf857x.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style pcf8574 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Warning: users will now have to use the force module parameter to get
the driver to attach to their device. That's not a bad thing as these
devices can't be detected anyway.
Note that this doesn't change the fact that this driver is deprecated
in favor of gpio/pcf857x.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style pcf8591 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style eeprom driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Clear i2c_adapter.dev on adapter removal. This makes it possible to
re-add the adapter at a later point, which some drivers
(i2c-amd756-s4882, i2c-nforce2-s4985) actually do.
This fixes a bug reported by John Stultz here:
http://lkml.org/lkml/2008/7/15/720
and by Ingo Molar there:
http://lkml.org/lkml/2008/7/16/78
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: (56 commits)
i2c: Add detection capability to new-style drivers
i2c: Call client_unregister for new-style devices too
i2c: Clean up old chip drivers
i2c-ibm_iic: Register child nodes
i2c: New-style EEPROM driver using device IDs
i2c: Export the i2c_bus_type symbol
i2c-au1550: Fix PM support
i2c-dev: Delete empty detach_client callback
i2c: Drop stray references to lm_sensors
i2c: Check for ACPI resource conflicts
i2c-ocores: basic PM support
i2c-sibyte: SWARM I2C board initialization
i2c-i801: Fix handling of error conditions
i2c-i801: Rename local variable temp to status
i2c-i801: Properly report bus arbitration loss
i2c-i801: Remove verbose debugging messages
i2c-algo-pcf: Drop unused struct members
i2c-algo-pcf: Multi-master lost-arbitration improvement
i2c: Deprecate the legacy gpio drivers
i2c-pxa: Initialize early
...
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
[ARM] 5171/1: ep93xx: fix compilation of modules using clocks
[ARM] 5133/2: at91sam9g20 defconfig file
[ARM] 5130/4: Support for the at91sam9g20
[ARM] 5160/1: IOP3XX: gpio/gpiolib support
[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
[ARM] 5084/1: zylonite: Register AC97 device
[ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
[ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
[ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
[ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
[ARM] 5144/1: pxaficp_ir: cleanup includes
[ARM] pxa: remove pxa_set_cken()
[ARM] pxa: allow clk aliases
[ARM] Feroceon: don't disable BPU on boot
[ARM] Orion: LED support for HP mv2120
[ARM] Orion: add RD88F5181L-FXO support
[ARM] Orion: add RD88F5181L-GE support
[ARM] Orion: add Netgear WNR854T support
[ARM] s3c2410_defconfig: update for current build
[ARM] Acer n30: Minor style and indentation fixes.
...
This includes PXA work up to the SPI changes for the initial merge,
since e172274ccc depends on the SPI
tree being merged.
Conflicts:
arch/arm/configs/em_x270_defconfig
arch/arm/configs/xm_x270_defconfig
Add a mechanism to let new-style i2c drivers optionally autodetect
devices they would support on selected buses and ask i2c-core to
instantiate them. This is a replacement for legacy i2c drivers, much
cleaner.
Where drivers had to implement both a legacy i2c_driver and a
new-style i2c_driver so far, this mechanism makes it possible to get
rid of the legacy i2c_driver and implement both enumerated and
detected device support with just one (new-style) i2c_driver.
Here is a quick conversion guide for these drivers, step by step:
* Delete the legacy driver definition, registration and removal.
Delete the attach_adapter and detach_client methods of the legacy
driver.
* Change the prototype of the legacy detect function from
static int foo_detect(struct i2c_adapter *adapter, int address, int kind);
to
static int foo_detect(struct i2c_client *client, int kind,
struct i2c_board_info *info);
* Set the new-style driver detect callback to this new function, and
set its address_data to &addr_data (addr_data is generally provided
by I2C_CLIENT_INSMOD.)
* Add the appropriate class to the new-style driver. This is
typically the class the legacy attach_adapter method was checking
for. Class checking is now mandatory (done by i2c-core.) See
<linux/i2c.h> for the list of available classes.
* Remove the i2c_client allocation and freeing from the detect
function. A pre-allocated client is now handed to you by i2c-core,
and is freed automatically.
* Make the detect function fill the type field of the i2c_board_info
structure it was passed as a parameter, and return 0, on success. If
the detection fails, return -ENODEV.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We call adapter->client_register for both legacy and new-style i2c
devices, however we only call adapter->client_unregister for legacy
drivers. This doesn't make much sense. Usually, drivers will undo
in client_unregister what they did in client_register, so we should
call neither or both for every given i2c device.
In order to ease the transition from legacy to new-style devices, it
seems preferable to actually call both.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Clean up old i2c chip drivers:
* Name the i2c_client "client" instead of "new_client".
* Drop useless initializations to 0.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch completes the conversion of the IBM IIC driver to an
of-platform driver.
It removes the index from the IBM IIC driver and makes it an unnumbered
driver. It then calls of_register_i2c_devices to properly register all
the child nodes in the DTS.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add a new-style driver for most I2C EEPROMs, giving sysfs read/write
access to their data. Tested with various chips and clock rates.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Enrik Berkhan
Dave Airlie
Roel Kluin
Jean Delvare
Wolfram Sang
Oskar Schirmer
Wolfgang Grandegger
Darius Augulis
Mark Brown
Daniel Silverstone
Ben Dooks
Linus Torvalds
Hans de Goede
Benjamin Herrenschmidt
Zhenwen Xu
Flavio Leitner
Shane Huang
Marco Aurelio da Costa
Frank Seidel
Russell King
Ming Lei
Timur Tabi
Russell King
Catalin Marinas
Anton Vorontsov
David Brownell
Kay Sievers
Ben Dooks
Magnus Damm
Mike Ditto
Harvey Harrison
Kalle Jokiniemi
Paul Walmsley
Tony Lindgren
Chandra shekhar
Nishanth Menon
Syed Mohammed Khasim
Jarkko Nikula
Julia Lawall
Lennart Sorensen
Arjan van de Ven
David Miller
Seth Heasley
Milton Miller
Parag Warudkar
Adrian Bunk
Greg Kroah-Hartman
Prakash Mortha
Marek Vasut
Rudolf Marek
Paul Mundt
Rene Herman
Felipe Balbi
Eric Miao
Jonathan Cameron
Sven Wegener
Uwe Kleine-Koenig
Kumar Gala
Dmitry Baryshkov
Mike Rapoport
Marc Pignat
Hans Verkuil
Michael Hennerich
Michael Buesch
Jonathan Corbet
Sean MacLennan