We get a build failure on ARM unless the header is included explicitly:
drivers/infiniband/hw/i40iw/i40iw_verbs.c: In function 'i40iw_get_vector_affinity':
drivers/infiniband/hw/i40iw/i40iw_verbs.c:2747:9: error: implicit declaration of function 'irq_get_affinity_mask'; did you mean 'irq_create_affinity_masks'? [-Werror=implicit-function-declaration]
return irq_get_affinity_mask(msix_vec->irq);
^~~~~~~~~~~~~~~~~~~~~
irq_create_affinity_masks
drivers/infiniband/hw/i40iw/i40iw_verbs.c:2747:9: error: returning 'int' from a function with return type 'const struct cpumask *' makes pointer from integer without a cast [-Werror=int-conversion]
return irq_get_affinity_mask(msix_vec->irq);
Fixes: 7e952b19eb ("i40iw: Implement get_vector_affinity API")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The mlx5 driver needs to be able to issue invalidation to ODP MRs
even if it cannot allocate memory. To this end it preallocates
emergency pages to use when the situation arises.
This flow should be extremely rare enough, that we don't need
to worry about contention and therefore a single emergency page
is good enough.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Instead synchronizing RCU in a loop when removing mkeys in a batch do it
once at the end before freeing them. The result is only waiting for one
RCU grace period instead of many serially.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
BYPASS namespace is used by the RDMA side to insert flow rules into
the vport RX flow tables. Currently only 8 priorities are exposed,
increase this to 16 to allow more flexibility. This change will also
cause the BYPASS namespace to use 32 levels (as apposed to 16 today) of
flow tables, 16 levels for regular rules and 16 for don't trap rules.
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Split IPv6 addresses at the colon that separates the IPv6 address
and the port number instead of at a colon in the middle of the IPv6
address. Check whether the IPv6 address is surrounded with square
brackets.
Fixes: 19f313438c ("IB/srp: Add RDMA/CM support")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
All callers to ib_modify_qp_is_ok() provides enum ib_qp_state
makes the checks of out-of-scope redundant. Let's remove them
together with updating function signature to return boolean result.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
QP states provided by core layer are converted to enum ib_qp_state
and better to use internal variable in that type instead of int.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The QP state is internal enum which is checked at the driver
level by calling to ib_modify_qp_is_ok(). Move this check closer
to user and leave kernel users to be checked by compiler.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In hfi.h, the header file opa_addr.h is included twice.
In vt.h, the header file mmap.h is included twice.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch updates to support cq record doorbell for
the kernel space.
Signed-off-by: Yixian Liu <liuyixian@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch updates to support rq record doorbell for
the kernel space.
Signed-off-by: Yixian Liu <liuyixian@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch updates to support cq record doorbell for
the user space.
Signed-off-by: Yixian Liu <liuyixian@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds interfaces and definitions to support the rq record
doorbell for the user space.
Signed-off-by: Yixian Liu <liuyixian@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that building with W=1 causes the following warning to appear:
drivers/infiniband/hw/hfi1/qp.c:484: warning: Cannot understand * on line 484 - I thought it was a doc line
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This series follows our previous one to lay out the foundations for IPSec
in user-space and extend current kernel netdev IPSec support. As noted in
our previous pull request cover letter "mlx5-updates-2018-02-28-1 (IPSec-1)",
the IPSec mechanism will be supported through our flow steering mechanism.
Therefore, we need to change the initialization order. Furthermore, IPsec
is also supported in both egress and ingress. Since our current flow
steering is egress only, we add an empty (only implemented through FPGA
steering ops) egress namespace to handle that case. We also implement
the required flow steering callbacks and logic in our FPGA driver.
We extend the FPGA support for ESN and modifying a xfrm too. Therefore, we
add support for some new FPGA command interface that supports them. The
other required bits are added too. The new features and requirements are
advertised via cap bits.
Last but not least, we revise our driver's accel_esp API. This API will be
shared between our netdev and IB driver, so we need to have all the required
functionality from both worlds.
Regards,
Aviad and Matan
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaoH8zAAoJEEg/ir3gV/o+h00H/RyM1xoGCzJtvQAYEhNcEfvY
YJfaJSPvuuvS2Fvs8meUzjqQvKcmkMjmViD3Ujuzyh6Y36IcoPWlBojRDE2fpz2b
yRaK5CotcLpfDXchlLnH5ZZbOgO374866viCVoM4i2ls19Ml730piDs8CDcA6+T7
3W4vvr977xl9bFqDMMbeldijZ3+H36Exnq6Xj+o2j6Sc1/om9Mvgw7XJhcpiBTW5
ZFfA7djz7TdSyBJDQsLteL/wLbLsLeqXmKCKX9BsqRo+rpoUWmskKFNC1Dj0bzX3
XbrdR8GoHVMS1PZAPJIbc1bubhqBznxrbh/g95PInSkGZzKKWw1dhS/3fkkAndM=
=Fodq
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-02-28-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux into k.o/wip/dl-for-next
mlx5-updates-2018-02-28-2 (IPSec-2)
This series follows our previous one to lay out the foundations for IPSec
in user-space and extend current kernel netdev IPSec support. As noted in
our previous pull request cover letter "mlx5-updates-2018-02-28-1 (IPSec-1)",
the IPSec mechanism will be supported through our flow steering mechanism.
Therefore, we need to change the initialization order. Furthermore, IPsec
is also supported in both egress and ingress. Since our current flow
steering is egress only, we add an empty (only implemented through FPGA
steering ops) egress namespace to handle that case. We also implement
the required flow steering callbacks and logic in our FPGA driver.
We extend the FPGA support for ESN and modifying a xfrm too. Therefore, we
add support for some new FPGA command interface that supports them. The
other required bits are added too. The new features and requirements are
advertised via cap bits.
Last but not least, we revise our driver's accel_esp API. This API will be
shared between our netdev and IB driver, so we need to have all the required
functionality from both worlds.
Regards,
Aviad and Matan
Signed-off-by: Doug Ledford <dledford@redhat.com>
Zero out the fields of the struct ib_pd for user mode pds so that
users querying pds via nldev will not get garbage. For simplicity,
use kzalloc() to allocate the mlx4_ib_pd struct.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Setting iova, length, and page_size allows this information to be
seen via NLDEV netlink queries, which can aid in user rdma debugging.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Some of the struct ib_mr fields weren't getting initialized. This was
benign, but will cause problems when dumping the mr resource via
nldev/restrack.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Implement RDMA nldev netlink interface to get detailed CM_ID information.
Because cm_id's are attached to rdma devices in various work queue
contexts, the pid and task information at restrak_add() time is sometimes
not useful. For example, an nvme/f host connection cm_id ends up being
bound to a device in a work queue context and the resulting pid at attach
time no longer exists after connection setup. So instead we mark all
cm_id's created via the rdma_ucm as "user", and all others as "kernel".
This required tweaking the restrack code a little. It also required
wrapping some rdma_cm functions to allow passing the module name string.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Move struct rdma_id_private to a new header cma_priv.h so the resource
tracking services in core/nldev.c can read useful information about cm_ids.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Create a common dumpit function that can be used by all common resource
types. This reduces code replication and simplifies the code as we add
more resource types.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Simplify res_to_dev() to make it easier to read/maintain.
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently ESN is not supported with IPSec device offload.
This patch adds ESN support to IPsec device offload.
Implementing new xfrm device operation to synchronize offloading device
ESN with xfrm received SN. New QP command to update SA state at the
following:
ESN 1 ESN 2 ESN 3
|-----------*-----------|-----------*-----------|-----------*
^ ^ ^ ^ ^ ^
^ - marks where QP command invoked to update the SA ESN state
machine.
| - marks the start of the ESN scope (0-2^32-1). At this point move SA
ESN overlap bit to zero and increment ESN.
* - marks the middle of the ESN scope (2^31). At this point move SA
ESN overlap bit to one.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Yossef Efraim <yossefe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
New function for getting driver internal sa entry from xfrm state.
All checks are done in one function.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to add a context to the FPGA, we need to get both the software
transform context (which includes the keys, etc) and the
source/destination IPs (which are included in the steering
rule). Therefore, we register new set of firmware like commands for
the FPGA. Each time a rule is added, the steering core infrastructure
calls the FPGA command layer. If the rule is intended for the FPGA,
it combines the IPs information with the software transformation
context and creates the respective hardware transform.
Afterwards, it calls the standard steering command layer.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current code has one layer that executed FPGA commands and
the Ethernet part directly used this code. Since downstream patches
introduces support for IPSec in mlx5_ib, we need to provide some
abstractions. This patch refactors the accel code into one layer
that creates a software IPSec transformation and another one which
creates the actual hardware context.
The internal command implementation is now hidden in the FPGA
core layer. The code also adds the ability to share FPGA hardware
contexts. If two contexts are the same, only a reference count
is taken.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch adds V2 command support.
New fpga devices support extended features (udp encap, esn etc...), this
features require new hardware sadb format therefore we have a new version
of commands to manipulate it.
Signed-off-by: Yossef Efraim <yossefe@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current hardware decrypts and authenticates incoming ESP packets.
Subsequently, the software extracts the nexthdr field, truncates the
trailer and adjusts csum accordingly.
With this patch and a capable device, the trailer is being removed
by the hardware and the nexthdr field is conveyed via PET. This way
we avoid both the need to access the trailer (cache miss) and to
compute its relative checksum, which significantly improve
the performance.
Experiment shows that trailer removal improves the performance by
2Gbps, (netperf). Both forwarding and host-to-host configurations.
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current code assume only SA QP commands.
Refactor in order to pave the way for new QP commands:
1. Generic cmd response format.
2. SA cmd checks are in dedicated functions.
3. Aligned debug prints.
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix build break of mlx5_accel_ipsec_device_caps is not defined when
MLX5_ACCEL is not selected, use MLX5_IPSEC_DEV instead which handles
such case.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Doug Ledford <dledford@redhat.com>
This struct is involved in the user API for mlx4 and should not be hidden
inside a driver header file.
Fixes: 09d208b258 ("IB/mlx4: Add report for RSS capabilities by vendor channel")
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
mlx5-updates-2018-02-28-1 (IPSec-1)
This series consists of some fixes and refactors for the mlx5 drivers,
especially around the FPGA and flow steering. Most of them are trivial
fixes and are the foundation of allowing IPSec acceleration from user-space.
We use flow steering abstraction in order to accelerate IPSec packets.
When a user creates a steering rule, [s]he states that we'll carry an
encrypt/decrypt flow action (using a specific configuration) for every
packet which conforms to a certain match. Since currently offloading these
packets is done via FPGA, we'll add another set of flow steering ops.
These ops will execute the required FPGA commands and then call the
standard steering ops.
In order to achieve this, we need that the commands will get all the
required information. Therefore, we pass the fte object and embed the
flow_action struct inside the fte. In addition, we add the shim layer
that will later be used for alternating between the standard and the
FPGA steering commands.
Some fixes, like " net/mlx5e: Wait for FPGA command responses with a timeout"
are very relevant for user-space applications, as these applications could
be killed, but we still want to wait for the FPGA and update the kernel's
database.
Regards,
Aviad and Matan
Signed-off-by: Doug Ledford <dledford@redhat.com>
The function rxe_init_device_param always return 0. So the function
type is changed to void.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In the function rxe_send, the variable rxe is not used in it.
So it should be removed.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In send_atomic_ack function, it is not necessary to make a
skb_clone. To gain better performance (high throughput and
low latency), this skb_clone is removed.
The following tests are made.
server client
--------- ---------
|1.1.1.1|<----rxe-channel--->|1.1.1.2|
--------- ---------
On server: rping -s -a 1.1.1.1 -v -C 1000 -S 512
On client: rping -c -a 1.1.1.1 -v -C 1000 -S 512
The kernel config CONFIG_DEBUG_KMEMLEAK is enabled on both server
and client.
This test runs for several hours. There is no memory leak and the whole
system can work well.
Based on the above network, the following tests are made.
Server: ibv_rc_pingpong -d rxe0 -g 1
Client: ibv_rc_pingpong -d rxe0 -g 1 1.1.1.1
The test results on Server(10 tests are made).
Before:
Throughput is 137.07 Mbit/sec
Latency is 517.76 usec/iter
After:
Throughput is 148.85 Mbit/sec
Latency is 476.64 usec/iter
The throughput is enhanced and the latency is reduced.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add a parameter for configuring the port on which the ib_srpt driver
listens for incoming RDMA/CM connections, namely
/sys/kernel/config/target/srpt/discovery_auth/rdma_cm_port. The default
value for this parameter is 0 which means "do not listen for incoming
RDMA/CM connections". Add RDMA/CM support to all code that handles
connection state changes. Modify srpt_init_nodeacl() such that ACLs can
be configured for IPv4 and IPv6 addresses.
Note: incoming connection requests are only accepted for ports that
have been enabled. See also the "if (!sport->enabled)" code in the
connection request handler. See also the following configfs attribute:
/sys/kernel/config/target/srpt/$port/$port/enable.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Previously, deleting a flow steering entry only got the index.
Since the FPGA implementation of FTE's deletion might need to dig
inside the FTE itself, we would like to get the FTE's context.
Changing the interface to pass the FTE context.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add helper functions that check if a protocol is
part of a flow steering match criteria.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
fte objects contain the match value and action. Currently, extending
the actions require in adding them both to the API and fs_fte.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, we don't support egress flow steering namespace in mlx5
flow steering core implementation. However, when we want to encrypt
a packet, we model it as a flow steering rule in the egress path.
To overcome this, we add an empty egress namespace to flow steering.
This namespace is initialized only when ipsec support exists.
In the future, this will grow to a full blown full steering
implementation, resembling the ingress path.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The shim layer allows each namespace to define possibly different
functionality for add/delete/update commands. The shim layer
introduced here, will be used to support flow steering with the FPGA.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The has_tag member will indicate whether a tag action was specified
in flow specification.
A flow tag 0 = MLX5_FS_DEFAULT_FLOW_TAG is assumed a valid flow tag
that is currently used by mlx5 RDMA driver, whereas in HW flow_tag = 0
means that the user doesn't care about flow_tag. HW always provide
a flow_tag = 0 if all flow tags requested on a specific flow are 0.
So we need a way (in the driver) to differentiate between a user really
requesting flow_tag = 0 and a user who does not care, in order to be
able to report conflicting flow tags on a specific flow.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>