This patch (as909) fixes a couple of refcounting errors in the sd
driver's suspend and resume methods.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use new esp_scsi for JAZZ SCSI host adapter driver
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a mix of a grand clean up I did and a reworking of the hotplug
support by Christoph. In testing it works as well as the previous code
did (that is -quite badly-) but we can now read it and as it settles in
actually debug the long standing problems it shares with the old driver.
Signed-off-by: Alan Cox <alan@redhat.com>
From Christoph:
removal of the BSD license is also fine with me, but should really
get a mention in the changelog aswell.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Back in the beginning of last year we disabled mode page 8 and mode page
3f requests through device quirk bits instead of enhancing the driver to
respond to these mode pages because there was no apparent added value.
The Firmware that supports the new communication commands supports the
ability to force a write around of the adapter cache on a command by
command basis. In the attached patch we enable mode page 8 and 3f and
spoof the results as needed in order to *convince* the layers above to
submit writes with the FUA (Force Unit Attention) bit set if the file
system or application requires it, if the Firmware supports the write
through, or instead to submit a SYNCHRONIZE_CACHE if the Firmware does
not. The added value here is for file systems that benefit from this
functionality and for clustering or redundancy scenarios.
Caveats: By convince, we are responding with a minimal short 3 byte
content mode page 8, with only the data the SCSI layer needs and that we
can fill confidently. Applications that require the customarily larger
mode page 8 results may be confused by this(?). The FUA, or the
SYNCHRONIZE_CACHE only affect the cache on the controller. Our firmware
by default ensure that the underlying physical drives of the array have
their cache turned off so normally this is not a problem.
This attached patch is against current scsi-misc-2.6 and was unit tested
on RHEL5. Since this is a feature enhancement, it should not be
considered for any current stabilization efforts.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use wait_for_completion_timeout instead a semaphore + timer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
With libata converted to use sdev->manage_start_stop for suspend and
resume, sht->suspend/resume() has no user left and low level
suspend/ressume should be taken care of by low level driver's
suspend/resume callbacks (e.g. PCI or PCMCIA driver callbacks). This
patch removes sht->suspend/resume() callbacks.
This change is suggested by Christoph Hellwig.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is basically a straight conversion. I have one of these things, so
I know it works ... my problem is that it has a wierd SCA like
connector, so I can't connect anything to it (no cables).
However, previously it panic'd in the interrupt, now it completes a bus
scan.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
First thing mm.h does is including sched.h solely for can_do_mlock() inline
function which has "current" dereference inside. By dealing with can_do_mlock()
mm.h can be detached from sched.h which is good. See below, why.
This patch
a) removes unconditional inclusion of sched.h from mm.h
b) makes can_do_mlock() normal function in mm/mlock.c
c) exports can_do_mlock() to not break compilation
d) adds sched.h inclusions back to files that were getting it indirectly.
e) adds less bloated headers to some files (asm/signal.h, jiffies.h) that were
getting them indirectly
Net result is:
a) mm.h users would get less code to open, read, preprocess, parse, ... if
they don't need sched.h
b) sched.h stops being dependency for significant number of files:
on x86_64 allmodconfig touching sched.h results in recompile of 4083 files,
after patch it's only 3744 (-8.3%).
Cross-compile tested on
all arm defconfigs, all mips defconfigs, all powerpc defconfigs,
alpha alpha-up
arm
i386 i386-up i386-defconfig i386-allnoconfig
ia64 ia64-up
m68k
mips
parisc parisc-up
powerpc powerpc-up
s390 s390-up
sparc sparc-up
sparc64 sparc64-up
um-x86_64
x86_64 x86_64-up x86_64-defconfig x86_64-allnoconfig
as well as my two usual configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
http://bugzilla.kernel.org/show_bug.cgi?id=8469
As discussed in the bugzilla outlined below, we have an sa based
(Mustang) RAID adapter on the system, a Dell PERC2/QC. Affected
controllers are HP NetRAID, Adaptec AAC-364, Dell PERC2/QC or Adaptec
5400S. This problem coincides with the introduction of the adapter_comm
and adapter_deliver platform functions (Message [PATCH 1/4] aacraid:
rework communication support code, January 23 2007, which initially
migrated to 2.6.21)
The panic occurs with an uninitialized adapter_deliver platform function
pointer. The enclosed patch, unmodified as tested by Rainer, solves the
problem.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This sets sg_dma_len to a proper value.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add debug information into abort and host_reset routine.
Change ioremap to ioremap_nocache.
Version updated to 3.6.0000.1.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
After reset completed, the scsi error handler sends out TEST_UNIT_READY
to the device. For 'normal' devices the command will be handled by firmware.
However, because the RAID console only interfaces to scsi mid layer, the
firmware will not process the command for it. This will make the console to
be offlined right after reset. Add the handling in driver to fix this problem.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
During hard bus reset of st_shasta controllers, 1 ms is not enough for
16-port controllers, although it's good for 8-port controllers. Extend the
wait time to 100 ms to allow bus resets finish successfully.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The correct internal mapping of stex controllers should be:
id:0~15, lun:0~7 (st_shasta)
id:0, lun:0~127 (st_yosemite)
id:0~127, lun:0 (st_vsc and st_vsc1)
This patch reports the internal mapping to scsi mid layer, eliminating
the translation between scsi mid layer and firmware. To achieve this
goal, we also need to:
-- fail the REPORT_LUNS command for st_shasta because the
firmware is known to not report all actual luns
-- add an entry in scsi_devindo.c to force sequential lun scan
(for st_shasta controllers)
-- fail the REPORT_LUNS command for console device
-- remove special handling of REPORT_LUNS command for
st_yosemite, as there is no translation mapping now
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently ipr always returns success from eh_dev_reset when
called for a SATA device. If ata_do_eh is unable to recover
for some reason, this can result in commands that are still
outstanding when ata_do_eh returns. Change ipr to verify no
commands are outstanding before returning success.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch provides support for FC virtual ports based on NPIV.
For information on the interfaces and design, please read the
Documentation/scsi/scsi_fc_transport.txt file enclosed within
the patch.
The RFC was originally posted here:
http://marc.info/?l=linux-scsi&m=117226959918393&w=2
Changes from the initial RFC:
- Bug fix: needed a transport_class_unregister() for the vport class
- Create a symlink to the vport in the shost device if it is not the
parent of the vport.
- Made symbolic name writable so it can be set after creation
- Made the temporary fc_vport_identifiers struct private to the
transport.
- Deleted the vport_id field from the vport. I couldn't find any good
use for it (and symname is a good replacement).
- Made the vport_state and vport_last_state "private" attributes.
Added the fc_vport_set_state() helper function to manage state
transitions
- Updated vport_create() to allow a vport to be created in a disabled
state.
- Added INITIALIZING and FAILED vport states
- Added VPCERR_xxx defines for errors to be returned from vport_create()
- Created a Documentation/scsi/scsi_fc_transport.txt file that describes
the interfaces and expected LLDD behaviors.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add devres ecardm_iomap() and ecardm_iounmap() for Acorn expansion
cards. Convert all expansion card drivers to use them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than having every driver fiddle about setting its private
IRQ operations and data, provide a helper function to contain
this functionality in one place.
Arrange to remove the driver-private IRQ operations and data when
the device is removed from the driver, and remove the driver
private code to do this.
This fixes potential problems caused by drivers forgetting to
remove these hooks.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: fix PIO setup on resume for ATAPI devices
ide: legacy PCI bus order probing fixes
ide: add ide_proc_register_port()
ide: add "initializing" argument to ide_register_hw()
ide: cable detection fixes (take 2)
ide: move IDE settings handling to ide-proc.c
ide: split off ioctl handling from IDE settings (v2)
ide: make /proc/ide/ optional
ide: add ide_tune_dma() helper
ide: rework the code for selecting the best DMA transfer mode (v3)
ide: fix UDMA/MWDMA/SWDMA masks (v3)
* move
__ide_add_setting()
ide_add_setting()
__ide_remove_setting()
auto_remove_settings()
ide_find_setting_by_name()
ide_read_setting()
ide_write_setting()
set_xfer_rate()
ide_add_generic_settings()
ide_register_subdriver()
ide_unregister_subdriver()
from ide.c to ide-proc.c
* set_{io_32bit,pio_mode,using_dma}() cannot be marked static now, fix it
* rename ide_[un]register_subdriver() to ide_proc_[un]register_driver(),
update device drivers to use new names
* add CONFIG_IDE_PROC_FS=n versions of ide_proc_[un]register_driver()
and ide_add_generic_settings()
* make ide_find_setting_by_name(), ide_{read,write}_setting()
and ide_{add,remove}_proc_entries() static
* cover IDE settings code in device drivers with CONFIG_IDE_PROC_FS #ifdef,
also while at it cover with CONFIG_IDE_PROC_FS #ifdef ide_driver_t.proc
* remove bogus comment from ide.h
* cover with CONFIG_IDE_PROC_FS #ifdef .proc and .settings in ide_drive_t
Besides saner code this patch results in the IDE core smaller by ~2 kB
(on x86-32) and IDE disk driver by ~1 kB (ditto) when CONFIG_IDE_PROC_FS=n.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* do write permission and min/max checks in ide_procset_t functions
* ide-disk.c: drive->id is always available so cleanup "multcount" setting
accordingly
* ide-disk.c: "address" setting was incorrectly defined as type TYPE_INTA,
fix it by using type TYPE_BYTE and updating ide_drive_t->adressing field,
the bug didn't trigger because this IDE setting uses custom ->set function
* ide.c: add set_ksettings() for handling HDIO_SET_KEEPSETTINGS ioctl
* ide.c: add set_unmaskirq() for handling HDIO_SET_UNMASKINTR ioctl
* handle ioctls directly in generic_ide_ioclt() and idedisk_ioctl()
instead of using IDE settings to deal with them
* remove no longer needed ide_find_setting_by_ioctl() and {read,write}_ioctl
fields from ide_settings_t, also remove now unused TYPE_INTA handling
v2:
* add missing EXPORT_SYMBOL_GPL(ide_setting_sem) needed now for ide-disk
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All important information/features should be already available through
sysfs and ioctl interfaces.
Add CONFIG_IDE_PROC_FS (CONFIG_SCSI_PROC_FS rip-off) config option,
disabling it makes IDE driver ~5 kB smaller (on x86-32).
While at it add CONFIG_PROC_FS=n versions of proc_ide_{create,destroy}()
and remove no longer needed #ifdefs.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Optimize fault kprobe handling just like powerpc.
[SPARC]: Wire up utimensat syscall.
[SPARC64]: Fix request_irq() ignored result warnings in PCI controller code.
[SPARC64]: Kill asm-sparc64/pbm.h
[ATYFB]: Fix sparc includes.
[QLA2XXX]: Fix build on sparc.
[SPARC64]: Removal of trivial pci_controller_info uses.
[SPARC64]: Move index info pci_pbm_info.
[SPARC64]: Move {setup,teardown}_msi_irq into pci_pbm_info.
[SPARC64]: Move pci_ops into pci_pbm_info.
[SPARC64] SBUS: Error interrupt registry cleanups.
[SPARC64] PCI: Use root list of pbm's instead of pci_controller_info's
[SPARC64] PCI: Kill PROM_PCIRNG_MAX and PROM_PCIIMAP_MAX.
[SPARC64] PCI: Use common routine to fetch PBM properties.
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (58 commits)
[SCSI] zfcp: clear boxed flag on unit reopen.
[SCSI] zfcp: clear adapter failed flag if an fsf request times out.
[SCSI] zfcp: rework request ID management.
[SCSI] zfcp: Fix deadlock between zfcp ERP and SCSI
[SCSI] zfcp: Locking for req_no and req_seq_no
[SCSI] zfcp: print S_ID and D_ID with 3 bytes
[SCSI] ipr: Use PCI-E reset API for new ipr adapter
[SCSI] qla2xxx: Update version number to 8.01.07-k7.
[SCSI] qla2xxx: Add MSI support.
[SCSI] qla2xxx: Correct pci_set_msi() usage semantics.
[SCSI] qla2xxx: Attempt to stop firmware only if it had been previously executed.
[SCSI] qla2xxx: Honor NVRAM port-down-retry-count settings.
[SCSI] qla2xxx: Error-out during probe() if we're unable to complete HBA initialization.
[SCSI] zfcp: Stop system after memory corruption
[SCSI] mesh: cleanup variable usage in interrupt handler
[SCSI] megaraid: replace yield() with cond_resched()
[SCSI] megaraid: fix warnings when CONFIG_PROC_FS=n
[SCSI] aacraid: correct SUN products to README
[SCSI] aacraid: superfluous adapter reset for IBM 8 series ServeRAID controllers
[SCSI] aacraid: kexec fix (reset interrupt handler)
...
We now use pci_device_to_OF_node() to get properties
and of_get_property() returns const pointers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the last users of the deprecated SA_xxx interrupt flags.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use a newly added PCI API to issue a PCI Fundamental reset
(warm reset) to a new ipr PCI-E adapter. Typically, the
ipr adapter uses the start BIST bit in config space to reset
an adapter. Issuing start BIST on this particular adapter
results in the PCI-E logic on the card losing sync, which
causes PCI-E errors, making the card unusable. The only reset
mechanism that exists on this hardware that does not have this
problem is PCI Fundamental reset (warm reset).
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Supported ISP types include ISP2422 and revision-2 type
ISP2432 chips.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hardcoding the qlport_down_retry module-parameter
effectively disallowed any user-defined NVRAM setting to go
into effect.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove a stale check against ha->device_flags
(DFLG_NO_CABLE) as topology scanning is performed within the
DPC-thread context.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
_ convert void* to struct mesh_state*
- remove unused irq argument from mesh_interrupt()
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For this driver cond_resched() seems to be a better alternative
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
drivers/scsi/megaraid.c: In function 'megaraid_probe_one':
drivers/scsi/megaraid.c:4893: warning: implicit declaration of function 'mega_create_proc_entry'
drivers/scsi/megaraid.c: In function 'megaraid_remove_one':
drivers/scsi/megaraid.c:4968: warning: unused variable 'buf'
Fix by adding #defines
Signed-off-by: walter harms <wharms@bfs.de>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (38 commits)
kconfig: fix mconf segmentation fault
kbuild: enable use of code from a different dir
kconfig: error out if recursive dependencies are found
kbuild: scripts/basic/fixdep segfault on pathological string-o-death
kconfig: correct minor typo in Kconfig warning message.
kconfig: fix path to modules.txt in Kconfig help
usr/Kconfig: fix typo
kernel-doc: alphabetically-sorted entries in index.html of 'htmldocs'
kbuild: be more explicit on missing .config file
kbuild: clarify the creation of the LOCALVERSION_AUTO string.
kbuild: propagate errors from find in scripts/gen_initramfs_list.sh
kconfig: refer to qt3 if we cannot find qt libraries
kbuild: handle compressed cpio initramfs-es
kbuild: ignore section mismatch warning for references from .paravirtprobe to .init.text
kbuild: remove stale comment in modpost.c
kbuild/mkuboot.sh: allow spaces in CROSS_COMPILE
kbuild: fix make mrproper for Documentation/DocBook/man
kbuild: remove kconfig binaries during make mrproper
kconfig/menuconfig: do not hardcode '.config'
kbuild: override build timestamp & version
...
The kexec patch introduced a superfluous (and otherwise inert) reset of
some adapters. The register can have a hardware default value that has
zeros for the undefined interrupts. This patch refines the test of the
interrupt enable register to focus on only the interrupts that affect
the driver in order to detect if an incomplete shutdown of the Adapter
had occurred (kdump).
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Another layer on this onion also discovered by Duane, the
interrupt enable handler also needed to be set ... The interrupt enable
was called from within the synchronous command handler.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Dynamically map the buffer for PIO for the residue byte.
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
cpu_to_le32 endianness conversions in tmscsim.c, followed by
arithmetic operations don't look correct. Besides, {in,out}[wl]
already perform the necessary conversions. Further, bus addresses
of request buffers are guaranteed to be (mapped) under 4G by
current scsi- and block-layer defaults. This could be explicitly
enforced by using blk_queue_bounce_limit(), which, however,
doesn't seem to be the common practice among SCSI drivers.
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
DMA_INT code is disabled since 1998, remove it to prepare
for further cleanup.
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If an ipr adapter encounters an adapter error requiring an
adapter reset to recover from prior to driver load time, the
error will be ignored and recovery will not happen until the
initial timeout occurs waiting for the firmware to come ready,
which means a five minute timeout. Fix is to read the interrupt
register before clearing any of the interrupts at probe time.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Per the comment in the change - it's not always prudent to immediately
remove the rport upon first notice of a disconnect. Make all rports
wait dev_loss_tmo before being deleted (and each could have a separate
dev_loss_tmo value).
The original post was:
http://marc.info/?l=linux-scsi&m=117392196006703&w=2
The repost contains the following changes:
- Bug fix in fc_starget_delete(). Dev_loss_tmo_callbk() was called prior to
tearing down the target. The callback is to be the last thing called, as
it tells the LLDD that the rport is completely finished and can be torn
down. Rework so that terminate_rport_io() is called to terminate the
outstanding io. Isolated work so it's is simply "starget" work.
- Fix holes in original patch. There were code paths that did not expect
the dev_loss_tmo timer to be running for the non-fcp rports.
- Bug Fix: the transport wasn't protecting against a LLDD calling
fc_remote_port_delete() back-to-back. Thus, the dev_loss_tmo timer
could be restarted such that it fires after the rport had been deleted.
Validate rport state before starting the timer.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Enables multi-initiator support on ipr RAID adapters that support it.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Formats ipr dual adapter errors so that they are more compact.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Increases the adapter operational timeout for some adapters that support
dual controller configurations, since they may take longer to come ready.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In ipr dual adapter configurations, the ipr adapter firmware
may require an adapter reset for various reasons. The reset
is requested by the adapter firmware logging an error with
an IOASC of 0x02048000. Add support to log this error, and
reset the adapter.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On newer levels of microcode for ipr RAID adapters supporting
multi-initiator configurations, the disk array, or VSET, resources
are capable of generating a check condition. This patch prevents
ipr from generating sense data in this scenario and retrieving it
from the logical device instead.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On certain ipr RAID adapters, which are capable of multi-initiator
configurations, the disk array, or VSET, resources will be in a POR
Unit Attention state following an adapter reset. In order for the
midlayer to handle the UA, I must report a bus reset to the logical
disk array bus at the end of an adapter reset.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since driver_data for pci ids in the ipr driver is now
just flags, we can allow these to be passed in from userspace
for dynamic ids.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes some scenarios where an ipr adapter
could get reset overlapped, which could cause very
long timeouts to occur, or PCI bus errors.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- make needlessly global code static
- #if 0 unused functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Added support for 8G speed and new HBAs.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support for async scanning
Notes: This is the async scan patch to our driver from Matthew Wilcox.
The async scan logic is still subject to errors in insmod/rmmod, as
the async scan threads don't get shutdown when the module unloads
underneath them. See http://marc.info/?l=linux-scsi&m=117551999925582&w=2
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Don't process ERATT interrupts when issuing KILL_BOARD mbx command
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Collapse discovery lists to a single node list.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Improve handling of failed ELS aborts.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Improve diagnostic messages and change local loopback message to KERN_INFO
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixed recovery of rport after race with dev_loss_tmo
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Round 2 of Miscellaneous fixes:
- Ensure we don't prematurely re-enable IRQs in lpfc_sli_abort_fcp_cmpl().
- Prevent freeing of iocb after IOCB_TIMEDOUT error.
- Added code to cleanup REG_LOGIN mailbox command when a LOGO is received.
- Fix offline window where more work can sneak in after clearing work_ha
- Use target reset instead of LU reset in bus_device_reset_handler
- Fixed system hangs due to leaked host_lock.
- Fixed NULL pointer dereference during I/O with LIP.
- Fixed false iocb timeout.
- Fixed name server query response handling.
- Change rport dev_loss_tmo value when user change lpfc HBA's dev_loss_tmo.
- Fixed a memory leak in lpfc_sli_wake_mbox_wait.
- Fixed check for dropped frames.
- Removed hba queue depth calculation based on device PCI IDs
- Change min cr_count value specified in comment to agree with setting
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Reorganize lpfc_nlp_list() and callers to prepare for nodelist simplification.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Modify ELS abort handling to prevent double completion
Rework portions of ELS abort handling to prevent double completion
- Rework ELS iotags and correct abort routine
- Move the (badly wrong) ELS completion logic from the initial ELS
abort request function to the ELS completion function.
- Fixup the iocb completion handling to account for the ELS abort
completions.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Misc bug fixes and code cleanup:
- Fix system hang while running on systems with IOMMU
- Fix use after free issues with rports
- Don't free mailbox structure if it's still on the mboxq list
- Decrement txq_cnt rather than txcmplq_cnt when parsing the txq list
- Use msleep for long delays to prevent soft lockup bug check
- Don't remove node during dev_loss_tmo if discovery is active
- Fix memory leaks in get/reset statistics and link attention paths
- Fixed lpfc_ns_rsp to handle entire GID_FT response.
- mbox interface should use MAILBOX_CMD_SIZE rather than sizeof(MAILBOX_t)
- Fixed bug check in add_timer.
- Fixup messages 0116, 0117, and 0128 to report ELS I/O tag.
- Remove unused parameter to lpfc_cleanup.
- Change mailbox timeout handling.
- Remove unused buflist. Code cleanup.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use the sysfs configurable timeout when issuing a START_UNIT
command from the scsi error handler. This is needed for devices which
take longer than thirty seconds to respond to the start
unit. The problem was observed when sending a start unit
to a disk array device in an ipr RAID adapter, which results
in the adapter firmware sending potentially multiple commands
to physical devices as a result of this command, which ended
up timing out sometimes. This patch does not change the default
value used for this command.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update the driver version reported by MEGAIOC_QDRVRVER to
match LSI_COMMON_MOD_VERSION.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Acked-by: "Patro, Sumant" <Sumant.Patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Inspired somewhat by Vignesh Babu <vignesh.babu@wipro.com> patch to
dpt_i2o.c to replace kmalloc/memset sequences with kzalloc, doing the
same for the aacraid driver.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It still used the long-deprecated "pci_module_init()" interface, rather
than the proper "pci_register_driver()" one.
[ I don't have the hardware, and I doubt many do, but the fix is
trivial and obvious, and can't be worse than not compiling ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (59 commits)
PCI: Free resource files in error path of pci_create_sysfs_dev_files()
pci-quirks: disable MSI on RS400-200 and RS480
PCI hotplug: Use menuconfig objects
PCI: ZT5550 CPCI Hotplug driver fix
PCI: rpaphp: Remove semaphores
PCI: rpaphp: Ensure more pcibios_add/pcibios_remove symmetry
PCI: rpaphp: Use pcibios_remove_pci_devices() symmetrically
PCI: rpaphp: Document is_php_dn()
PCI: rpaphp: Document find_php_slot()
PCI: rpaphp: Rename rpaphp_register_pci_slot() to rpaphp_enable_slot()
PCI: rpaphp: refactor tail call to rpaphp_register_slot()
PCI: rpaphp: remove rpaphp_set_attention_status()
PCI: rpaphp: remove print_slot_pci_funcs()
PCI: rpaphp: Remove setup_pci_slot()
PCI: rpaphp: remove a call that does nothing but a pointer lookup
PCI: rpaphp: Remove another wrappered function
PCI: rpaphp: Remve another call that is a wrapper
PCI: rpaphp: remove a function that does nothing but wrap debug printks
PCI: rpaphp: Remove un-needed goto
PCI: rpaphp: Fix a memleak; slot->location string was never freed
...
SCSI should be working on a TT (but someone should really try!) but causes
trouble on a Falcon (as in: it ate a filesystem of mine) at least when
used concurrently with IDE. I have the notion it's because locking of the
ST-DMA interrupt by IDE is broken in 2.6 (the IDE driver always complains
about trying to release an already-released ST-DMA). Needs more work, but
that's on the IDE or m68k interrupt side rather than SCSI.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert code that allocs a struct pci_dev to use alloc_pci_dev().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation/modules.txt doesn't exist, but
Documentation/kbuild/modules.txt does.
Signed-off-by: Alexander E. Patrakov
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
These are all the remaining instances of get_property. Simple rename of
get_property to of_get_property.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block:
[PATCH] elevator: elv_list_lock does not need irq disabling
[BLOCK] Don't pin lots of memory in mempools
cfq-iosched: speedup cic rb lookup
ll_rw_blk: add io_context private pointer
cfq-iosched: get rid of cfqq hash
cfq-iosched: tighten queue request overlap condition
cfq-iosched: improve sync vs async workloads
cfq-iosched: never allow an async queue idling
cfq-iosched: get rid of ->dispatch_slice
cfq-iosched: don't pass unused preemption variable around
cfq-iosched: get rid of ->cur_rr and ->cfq_list
cfq-iosched: slice offset should take ioprio into account
[PATCH] cfq-iosched: style cleanups and comments
cfq-iosched: sort IDLE queues into the rbtree
cfq-iosched: sort RT queues into the rbtree
[PATCH] cfq-iosched: speed up rbtree handling
cfq-iosched: rework the whole round-robin list concept
cfq-iosched: minor updates
cfq-iosched: development update
cfq-iosched: improve preemption for cooperating tasks
Some sparc64 boxes don't have a valid NVRAM (from which the driver
takes its WWPN) try to extract this from open firmware instead and if
that fails, fall back to a default, which would be invalid if more
than one machine on the same SAN does this, since two machines with
the same WWPN would be illegal, so warn when taking this potentially
invalid default.
Tested on SunBlade-1000:
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently we scale the mempool sizes depending on memory installed
in the machine, except for the bio pool itself which sits at a fixed
256 entry pre-allocation.
There's really no point in "optimizing" this OOM path, we just need
enough preallocated to make progress. A single unit is enough, lets
scale it down to 2 just to be on the safe side.
This patch saves ~150kb of pinned kernel memory on a 32-bit box.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
drivers/scsi/ipr.c: In function '__ipr_eh_dev_reset':
drivers/scsi/ipr.c:3865: warning: passing argument 4 of 'ata_do_eh' from incompatible pointer type
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
irqreturn.h for irqreturn_t and dma_addr_t being u128 warnings ;-)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCSI was using the incorrect lock to protect walking the list of all
devices in the class. This patch fixes this.
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (67 commits)
[SCSI] SUNESP: Complete driver rewrite to version 2.0
[SPARC64]: Convert PCI over to generic struct iommu/strbuf.
[SPARC]: device_node name constification fallout
[SPARC64]: Convert SBUS over to generic iommu/strbuf structs.
[SPARC64]: Add generic iommu and strbuf structs to iommu.h
[SPARC64]: Consolidate {sbus,pci}_iommu_arena.
[SPARC]: Make device_node name and type const
[SPARC64]: constify some paramaters of OF routines
[TIGON3]: of_get_property() returns const.
[SPARC64]: Fix PCI rework to adhere to of_get_property() const return.
[SPARC64]: Document and fix calculation of pages_avail.
[SPARC64]: Make sure pbm->prom_node is setup easly enough in psycho.c
[SPARC64]: Use bootmem_bootmap_pages() in choose_bootmap_pfn().
[SPARC64]: Add proper header file extern for cmdline_memory_size.
[SPARC64]: Kill sparc_ultra_dump_{i,d}tlb()
[SPARC64]: Use DECLARE_BITMAP and BITS_TO_LONGS in mm/init.c
[SPARC64]: Give move verbose show_mem() output just like i386.
[SPARC64]: Mark show_mem() printk's with KERN_INFO.
[SPARC64]: Kill kvaddr_to_phys() and friends.
[SPARC64]: Privatize sun4u_get_pte() and fix name.
...
Major features:
1) Tagged queuing support.
2) Will properly negotiate for synchronous transfers even on
devices that reject the wide negotiation message, such as
CDROMs
3) Significantly lower kernel stack usage in interrupt
handler path by elimination of function vector arrays,
replaced by a top-level switch statement state machine.
4) Uses generic scsi infrastructure as much as possible to
avoid code duplication.
5) Automatic request of sense data in response to CHECK_CONDITION
6) Portable to other platforms using ESP such as DEC and Sun3
systems.
Signed-off-by: David S. Miller <davem@davemloft.net>
The only unfortunate bit here is that the name field of struct map_info
is not const, so for now we put a cast on the assignment of it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch cb_lock to mutex and allow netlink kernel users to override it
with a subsystem specific mutex for consistent locking in dump callbacks.
All netlink_dump_start users have been audited not to rely on any
side-effects of the previously used spinlock.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common "(struct nlmsghdr *)skb->data" sequence, so that we reduce the
number of direct accesses to skb->data and for consistency with all the other
cast skb member helpers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch adds support for sysfs/uevent modalias
attribute for scsi devices (like disks, tapes, cdroms etc),
based on whatever current sd.c, sr.c, st.c and osst.c drivers
supports.
The modalias format is like this:
scsi:type-0x04
(for TYPE_WORM, handled by sr.c now).
Several comments.
o This hexadecimal type value is because all TYPE_XXX constants
in include/scsi/scsi.h are given in hex, but __stringify() will
not convert them to decimal (so it will NOT be scsi:type-4).
Since it does not really matter in which format it is, while
both modalias in module and modalias attribute match each other,
I descided to go for that 0x%02x format (and added a comment in
include/scsi/scsi.h to keep them that way), instead of changing
them all to decimal.
o There was no .uevent routine for SCSI bus. It might be a good
idea to add some more ueven environment variables in there.
o osst.c driver handles tapes too, like st.c, but only SOME tapes.
With this setup, hotplug scripts (or whatever is used by the
user) will try to load both st and osst modules for all SCSI
tapes found, because both modules have scsi:type-0x01 alias).
It is not harmful, but one extra module is no good either.
It is possible to solve this, by exporting more info in
modalias attribute, including vendor and device identification
strings, so that modalias becomes something like
scsi:type-0x12:vendor-Adaptec LTD:device-OnStream Tape Drive
and having that, match for all 3 attributes, not only device
type. But oh well, vendor and device strings may be large,
and they do contain spaces and whatnot.
So I left them for now, awaiting for comments first.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch (as857) modifies the SG_GET_RESERVED_SIZE and
SG_SET_RESERVED_SIZE ioctls in the sg driver, capping the values at
the device's request_queue's max_sectors value. This will permit
cdrecord to obtain a legal value for the maximum transfer length,
fixing Bugzilla #7026.
The patch also caps the initial reserved_size value. There's no
reason to have a reserved buffer larger than max_sectors, since it
would be impossible to use the extra space.
The corresponding ioctls in the block layer are modified similarly,
and the initial value for the reserved_size is set as large as
possible. This will effectively make it default to max_sectors.
Note that the actual value is meaningless anyway, since block devices
don't have a reserved buffer.
Finally, the BLKSECTGET ioctl is added to sg, so that there will be a
uniform way for users to determine the actual max_sectors value for
any raw SCSI transport.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I got so sick of seing the check_region warnings from BusLogic.c I actually
fixed it properly. Never use check region, reserve it before the probe
with request region instead and check the error result; free region if
setup fails. Should be functionally identical to the original except for
fixing the potential race.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- ibmstgt hits the max rdma transfer size (128k).
- libsrp returns a rdma transfer error properly.
Signed-off-by: Bastian Blank <bastian@waldi.eu.org>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Thanks for the help from Steve Fox and Duane Cox investigating this
issue, I'd like to report that we found the problem. The issue is with
the patch Steve Fox isolated below, by not accommodating older adapters
properly and issuing a command they do not support when retrieving
storage parameters about the arrays. This simple patch resolves the
problem (and more accurately mimics the logic of the original code
before the patch).
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently, the scsi error handler will issue a START_UNIT
command if the drive indicates it needs its motor started
and the allow_restart flag is set in the scsi_device. If,
after the scsi error handler invokes a host adapter reset
due to error recovery, a device is in a unit attention
state AND also needs a START_UNIT, that device will be placed
offline. The disk array devices on an ipr RAID adapter
will do exactly this when in a dual initiator configuration.
This patch adds a single retry to the EH initiated
START_UNIT.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Patch modified and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We only map DMA when cmd->request_bufflen is non-zero for non-sg
buffers, we thus should make the same check when unmapping.
Based upon a report from Pasi Pirhonen.
Signed-off-by: David S. Miller <davem@davemloft.net>
3w-xxxx emulates a REQUEST_SENSE response by simply returning nothing.
Unfortunately, it's assuming that the REQUEST_SENSE command is
implemented with use_sg == 0, which is no longer the case. The oops
occurs because it's clearing the scatterlist in request_buffer instead
of the memory region.
This is fixed by using tw_transfer_internal() to transfer correctly to
the scatterlist.
Acked-by: adam radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a regression caused by commit:
2dc611de5a
The sense buffer code in scsi_send_eh_cmnd was changed to use
alloc_page() and a scatter list, but the sense data copy was not
updated to match so what we actually get in the sense buffer is total
grabage starting with the kernel address of the struct page we got.
Basically the stack frame of scsi_send_eh_cmd() is what ends up
in the sense buffer.
Depending upon how pointers look on a given platform, you can
end up getting sr_ioctl.c errors when you mount a cdrom. If
the CDROM gives a check condition for GPCMD_GET_CONFIGURATION issued
by drivers/cdrom/cdrom.c:cdrom_mmc_profile(), sr_ioctl will
spit out this error message in sr_do_ioctl() with the way pointers
are on sparc64:
default:
printk(KERN_ERR "%s: CDROM (ioctl) error, command: ", cd->cdi.name);
__scsi_print_command(cgc->cmd);
scsi_print_sense_hdr("sr", &sshdr);
err = -EIO;
This is the error Tom Callaway reported in:
http://marc.info/?l=linux-sparc&m=117407453208101&w=2
Anyways, fix this by using page_address(sgl.page) which is OK
because we know this is low-mem due to GFP_ATOMIC.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Christoph Hellwig <hch@lst.de>
Attached is the patch I feel will address this issue. As an added
'perk' I have also added the code to detect if the controller was
previously initialized for interrupted operations by ANY operating
system should the reset_devices kernel parameter not be set and we are
dealing with a naïve kexec without the addition of this kernel
parameter. The reset handler is also improved. Related to reset
operations, but not pertinent specifically to this issue, I have also
altered the handling somewhat so that we reset the adapter if we feel
it is taking too long (three minutes) to start up.
We have not unit tested the reset_devices flag propagation to this
driver code, nor have we unit tested the check for the interrupted
operations under the conditions of a naively issued kexec. We are
submitting this modified driver to our Q/A department for integration
testing in our current programs. I would appreciate an ACK to this
patch should it resolve the issue described in this thread...
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Improve overall command performance by embedding the scatterlist
in the command block used by the adapter. This decreases
the overall number of DMAs required for a single command.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If qc_issue fails for some reason, return a better error
to libata.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add entry in ipr error translation table for an error
received when a device is forced into the failed state
by the user.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add the ability to control how much error data gets logged
on a per error basis.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix to make sure user config accesses get re-enabled if the
PCI config write to start BIST fails.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes a problem discovered on a system with some
bad SATA devices attached. If a command to a SATAPI device
times out and the device gets reset as part of error recovery,
its possible that ipr will set err_mask to indicate a device
error has occurred. If this happens, a request sense will get
issued by libata. Since scsi core thinks this scsi command is
now completed, because the device reset handler completed successfully,
scsi core will free the associated scsi command, which may
cause an oops when that request sense is completed later
by ipr. This patch ensures that any commands that get aborted
as a result of a device reset set err_mask appropriately so
that the request sense does not get sent.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For ipr SAS adapters that support dual pathing, this
patch modifies ipr to log an error when a path fails.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The ipr driver has a sysfs attribute which can be used to
adjust the logging level of the driver for error events.
The error response data for commands can be dumped by
increasing the logging level of the ipr driver. This
currently only works for JBOD passthrough devices.
This patch enables this function for all devices, including
RAID devices, to aid in debugging problems.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adds support for some new PCI-E ipr adapters.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove the auto RAID 0 array creation module parameter, since
support for this function has been removed from the firmware.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some ipr adapters may take longer than others to come operational.
This patch makes this timeout different for different adapters,
while still preserving the module parameter which can be used
to globally override the default.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixed the kernel-doc comment for ibmvscsi_slave_configure. Thanks to
Randy Dunlap for pointing this out.
Adding a slave_configure function for the driver. Now the disks can be
restarted by the scsi mid-layer when the are disconnected and reconnected.
Signed-off-by: "Robert Jennings" <rcj@linux.vnet.ibm.com>
Signed-off-by: "Santiago Leon" <santil@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The request limit calculations used previously on the client failed to
mirror the state of the server. Additionally, when a value < 3 was provided
there could be problems setting can_queue and handling abort and reset
commands.
Signed-off-by: "Robert Jennings" <rcj@linux.vnet.ibm.com>
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The Adapter build date that is to be printed on instantiation was not
displayed as a result of the supplemental adapter information structure
not being in sync with the Firmware; the driver took an early test cycle
version that had a miss-sized padded region at the head and the
structure was not re-checked at the end of qualification. The Build Date
was not a priority and is merely a cosmetic enhancement, and the wrong
location for the start of the structure member would not induce any
side-effect problems. We updated the structure to match the actual
format, and added the TSID (Tech Support Identification) value print,
should it be present, to the adapter instantiation announcements during
driver load.
This later enhancement should improve the relationship between Service
folk & Tech Support if the printed value of the TSID found it's way into
the circular file labeled G...
Neither of these values show in sysfs (yet).
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Just sweeping the floor clean in one spot. Some of these constants have
never been used in the driver or in the firmware (and thus are
meaningless). Triggered this patch because I discovered one of the
unused constants was actually incorrect and figured it was better to
clean them out than correct and update. There are no side effects at all
regarding this patch, it is purely cosmetic.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On the path qla2x00_probe_one() -> probe_failed -> qla2x00_free_device(),
pci_disable_device() is executed twice, once in qla2x00_free_device()
and once in qla2x00_probe_one().
This patch removes the unnecessary call.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Unsigned long is not always the same size as a pointer, namely on 32 bit
systems with 64 bit address space. Ptrdiff_t is the same size as a
pointer in all configurations. By using ptrdiff_t we can mitigate the
warning messages on these configurations. There should be no side
effects of this patch.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- proper prototypes for global code in aacraid.h
- aac_rx_start_adapter() can now become static
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The Coverity checker spotted this dead code introduced by
commit a07f353701.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove the unused SCSI-related kernel config variables
SCSI_NCR53C8XX_PROFILE_SUPPORT
SCSI_NCR53C8XX_PROFILE
53C700_IO_MAPPED
AIC79XX_ENABLE_RD_STRM
AIC7XXX_PROBE_EISA_VL
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove some trailing whitespaces and some replace whitespaces with tabs.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove the Kconfig requirement that the PCMCIA SCSI drivers be built
only as modules, and allow them to be built into the kernel.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add some likely() and unlikely() compiler hints in some of the aacraid
hardware interface layers. There should be no operational side effects
resulting from this patch and the changes should be mostly benign on x86
platforms.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes byte swap issue in qla2xxx driver
to fix corrupted fabric_name passed to
/sys/class/fc_host/host*/fabric_name.
Signed-off-by: Richard Lary <rlary@us.ibm.com>
Acked-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We have seen two cases where VPD on an emulex card has been incorrect
and we end up walking off the end of memory. It looks like someone made
an update (increased the length of a string) without increasing the
Length field. Then we do:
Length -= (3+i);
And since Length is unsigned it becomes very large and we loop forever
in the encapsulating:
while (Length > 0) {
If we make Length signed then we fall out of the loop and proceed on.
Its important to note we have only seen this in the lab and it may be
the only two cases of this in existence, but since the rest of the code
has been written to be resilient against bad VPD we may as well fix this
too.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There is some residual cleanup of the last series of patches and the
need to bump the revision number to draw the line in the sand.
The cmd->SCp.phase is set in the aac_valid_context routine, then set
again to the same value following it's return. The cmd->scsi_done is set
twice in the aac_queuecommand routine. Free up the scsidev FILO in
aac_probe_container as it is not needed further down the function in any
case. Improve the efficiency of the abort handler kernel print
parameters. Bump revision number of driver to approximate the equivalent
in the Adaptec supplied version.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Captured a panic on an older kernel where an application issuing
commands via sg was sending requests that lacked a request_buffer, thus
the buffer pointer used in aac_internal_transer was NULL. The
application was fixed closing the issue, but felt it was advised to
immunize the driver against the eventuality.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The #ifdef MODULE around the export of scsi_complete_async_scans()
which is the API the scsi_wait_scan module uses is incorrect and
causes the symbol to be undefined in certain circumstances leading to
a build failure. Remove the defines.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Implement SBC START/STOP management. sdev->mange_start_stop is added.
When it's set to one, sd STOPs the device on suspend and shutdown and
STARTs it on resume. sdev->manage_start_stop defaults is in sdev
instead of scsi_disk cdev to allow ->slave_config() override the
default configuration but is exported under scsi_disk sysfs node as
sdev->allow_restart is.
When manage_start_stop is zero (the default value), this patch doesn't
introduce any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Rejections fixed and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sd_sync_cache() should return -errno on error, fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
eata_generic.h is only included by eata_pio.c and it only uses
FALSE/TRUE in comments.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It looks like megaraid_sas at least needs this to throttle its commands
as they begin to time out. The code keeps the existing transport
template use of eh_timed_out (and allows the transport to override the
host if they both have this callback).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn,
This set of fixes improve error handling stability of the driver. A popular
manifestation of the problems is an NULL pointer reference in the interrupt
handler when referencing portions of the scsi command context, or in the
scsi_done handling when an offlined device is referenced.
The aacraid driver currently does not get notification of orphaned command
completions due to devices going offline. The driver also fails to handle the
commands that are finished by the error handler, and thus can complete again
later at the hands of the adapter causing situations of completion of an
invalid scsi command context. Test Unit Ready calls abort assuming that the
abort was successful, but are not, and thus when the interrupt from the adapter
occurs, they reference invalid command contexts. We add in a TIMED_OUT flag to
inform the aacraid FIB context that the interrupt service should merely release
the driver resources and not complete the command up. We take advantage of this
with the abort handler as well for select abortable commands. And we detect and
react if a command that can not be aborted is currently still outstanding to
the controller when reissued by the retry mechanism.
Signed-off-by: Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn,
The raw srb ioctl is supposed to be able to take packets with 32 and 64 bit
virtual address SG elements, it did not handle the frames with 64 bit SG
elements well when communicating with 64 bit DMA capable adapters, and it did
not handle the 32 bit limited DMA adapters at all. The enclosed patch now
handles all four quadrants (32 bit / 64 bit SG elements in SRB requests + 32
bit or 64 bit DMA capable adapters)
This fix is required before Java based management applications in a 64 bit user
space can submit raw srb requests to the array physical components via the
ioctl mechanism, the allocated user memory pool on 64 bit machines under this
environment forced the management software's hands to submit 64 bit user space
virtual address SG elements in via the ioctl.
Signed-off-by: Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn,
This little patch removes the ',cid)' container identification argument
from some of the functions. The argument is used in some cases as merely
a debug helper and thus not used, and in others, the value can be
quickly acquired from the scsi command in their single solitary use in
the procedure rather than wasting resources on passing the argument in
from above.
Signed-off-by: Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn,
Outstanding ioctl calls still have some problems with aborting cleanly
in the face of a reset iop recovery action should the adapter ever enter
into a Firmware Assert (BlinkLED) condition. The enclosed patch resolves
some uncovered flawed handling.
Signed-off-by: Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn,
The aac_probe_container call blocks. This is an issue because it is called on
occasion in the context of the queuecommand handler. Once in a blue moon this
has resulted in a kernel panic sleeping during interrupt; or problems with some
embedded system versions of the kernel that depend on queuecommand to not
block. This ugly patch rewrites the aac_probe_container call into a new routine
_aac_probe_container that is an asynchronous state machine to complete the
series of operations. The legacy blocking aac_probe_container call used in
other areas of the driver (during initialization scanning for all targets and
in the separate hot-add/remove [aacraid] thread) merely issues
_aac_probe_container and then simple spins calling schedule() waiting for
completion.
Signed-off-by: Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn,
This patch is to resolve a namespace issue that will result from a patch
expected in the future that adds a new interface; rationalized as
correcting a long term issue where hw_fib, instead of hw_fib_va, refers
to the virtual address space and hw_fib_pa refers to the physical
address space. A small fragment of this patch also cleans up an unused
variable that was close to the patch fragments.
Signed-off-by: Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn,
This patch updates the adapter restart function to deal with some
adapters that have specific IOP reset needs. Since the code for
restarting the adapter was in two places, changed over to utilizing a
platform function in one place.
Signed-off-by: Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some targets can return both valid data and sense information.
Always update the request data_len from the SCSI command residual.
Callers should interpret sense data to determine what parts of the
data are valid in case of a CHECK CONDITION status.
Signed-off-by: Pete Wyckoff <pw@osc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
tgt notifies a LLD of the failure with sense when it hits the
user-space daemon bugs. However, tgt doesn't know anything about SCSI
devices that initiators talks to. So it's impossible to send proper
sense buffer (format and contents).
This patch changes tgt not to notify a LLD of the failure with bogus
sense. Instead, tgt just re-queues the failure command to the internal
list so that it will be freed cleanly later on when the scsi_host is
removed.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch updates the FC transport for all speeds identified in
SM-HBA. Note: it does not sync the "bit" definitions, as that is
actually insulated from user-space via the sysfs text string. (I could
do it, but it does introduce a potential binary-incompatibility).
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The module parameter, ql2xextended_error_logging, can now be
set dynamically by writing to the following sysfs entry:
/sys/module/qla2xxx/parameters/ql2xextended_error_logging
This alleviates the need for the driver to be unloaded and
reloaded in order to enable logging.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's no need given, I/O has been quiesced, RISC
interrupts have been disabled, and finally the RISC has been
paused. Flash manipulation on ISP21xx, ISP22xx, and ISP23xx
parts requires the RISC to go through a full reset to
recover.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We're observing soft lockups during HBA FLASH retrieval and
update. Add cond_resched() each time around the tight-loops
during flash read()s/write()s.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
qla2xxx driver fails to handle RSCN events affecting area or domain due
to an endian issue on big endian systems. This fixes the port_id_t
structure on big endian systems.
Signed-off-by: Malahal Naineni <malahal@us.ibm.com>
Acked-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently scsi_wait_scan is only built modular if SCSI is modular.
However, it's perfectly possible for a built in SCSI still to have
modular drivers and thus need scsi_wait_scan as a module. Therefore,
scsi_wait_scan should always be built as a module (unless the kernel
doesn't support modules).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch (as868) adds a helper routine for device drivers that need
to set up a callback to perform some action in a different process's
context. This is intended for use by attribute methods that want to
unregister themselves or their parent device. Attribute method calls
are mutually exclusive with unregistration, so such actions cannot be
taken directly.
Two attribute methods are converted to use the new helper routine: one
for SCSI device deletion and one for System/390 ccwgroup devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver was removed a while ago by commit
099175c94a
However, it seems that pci2000.h wasn't properly eliminated, so remove
it now.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The failure to map user-space pages leads to scsi command leak. It can
happens mostly because of user-space daemon bugs (or OOM). This patch
makes tgt just notify a LLD of the failure with sense when
blk_rq_map_user() fails.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch simplify the way to notify LLDs of the command completion
and addresses the following sense buffer problems:
- can't handle both data and sense.
- forces user-space to use aligned sense buffer
tgt copies sense_data from userspace to cmnd->sense_buffer (if
necessary), maps user-space pages (if necessary) and then calls
host->transfer_response (host->transfer_data is removed).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi tgt breaks up a command into multple scatterlists
if we cannot fit all the data in one. This was because
the block rq helpers did not support large requests and
because we can get a command of any old size so it is
hard to preallocate pages for scatterlist large enough
(we cannot really preallocate pages with the bio map
user path). In 2.6.20, we added large request support to
the block layer helper, blk_rq_map_user. And at LSF,
we talked about increasing SCSI_MAX_PHYS_SEGMENTS for
scsi tgt if we want to support really really :) large
(greater than 256 * PAGE_SIZE in the worst mapping case)
requests.
The only target currently implemented does not even support
the multiple scatterlists stuff and only supports smaller
requests, so this patch just coverts scsi tgt to use
blk_rq_map_user.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
People do not read the README and seem to like to
unselect the crc32c module even though iscsi_tcp selects
it for them. This patch spits a error that tells the user
that they really do need the module. Hopefully, we will
get fewer people asking about this now.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For a while now, the block layer has seperated max sectors
and max hw sectors. Software iscsi has no limit so this patch
increases max hw sectors, so we can support large pass through
commands.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Dave Miller meantioned that the data buffer in a past
sense fixup patch was not gauranteed to be aligned
properly for ia64. This patch has libiscsi use get_unalinged
to make sure. There are a couple more places in the
digest handling we may need to do this, but we are in the middle
of fixing that code for big endien systems so just the sense
access is fixed here.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
qla4xxx and iscsi_tcp or iser could be creating
sessions at the same time, so make session_nr id
allocation atomic.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch renames DEFAULT_MAX_RECV_DATA_SEGMENT_LENGTH to avoid
confusion with the drivers default values (DEFAULT_MAX_RECV_DATA_SEGMENT_LENGTH
is the iscsi RFC specific default).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It's possible that we call iscsi_xmitworker after iscsi_conn_release
which causes a oops. This patch flushes the workqueue.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add missing additional sense code and provide pointer to upstream
reference (from Doug Gilbert).
Add missing const (from Michael Tokarev).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert the sd.c SCSI logging calls to scmd_printk()/sd_printk()
instead of plain printk().
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make SCSI disk printing more consistent:
- Define sd_printk(), sd_print_sense_hdr() and sd_print_result()
- Move relevant header bits into sd.h
- Remove all the legacy disk_name passing and use scsi_disk pointers
where possible
- Switch printk() lines to the new sd_ functions so that output is
consistent
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch enhances SCSI error printing by:
- Making use of scsi_print_result() in the completion functions.
- Having scmd_printk() output the disk name (when applicable).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Clean up constants.c and make result printing more user friendly:
- Refactor the command and sense functions so that the actual
formatting can be called from the various helper functions with the
correct prefix.
- Replace scsi_print_hostbyte() and scsi_print_driverbyte() with
scsi_print_result() which is verbose when CONFIG_SCSI_CONSTANTS is
on.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Recent alterations to the gdth_fill_raw_cmd() path no longer set the
sg_ranz field for zero transfer commands. However, this field is used
lower down in the function to initialise ha->cmd_len to the size of
the firmware packet. If this uninitialised field contains a bogus
value, ha->cmd_len can become much larger than the actual firmware
packet and end up oopsing in gdth_copy_cmd() as it tries to copy this
huge packet to the device (usually because it runs into an unallocated
page).
The fix is to initialise the sg_ranz field to zero at the start of
gdth_fill_raw_cmd().
Signed-off-by: Joerg Dorchain <joerg@dorchain.net>
Acked-by: "Leubner, Achim" <Achim_Leubner@adaptec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If a PCI error is detected that cannot be recovered from, there
will be a double call of lpfc_pci_remove_one(), with the second call
resulting in a null-pointer dereference. The first call occurs in
lpfc_io_error_detected(), and the second call during pci device
remove. This patch eliminates the first call; its un-needed.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
An off-by-one bug meant we were always trying to map one too many
scatterlist entries. This was mostly harmless prior to the checks
going in to consistent_sync(), but now causes the kernel to BUG.
Also, powertec.c was missing an assignment to info->ec.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SCSI doesn't want drivers to modify request_bufflen, so keep a
driver-private copy of this in the scsi_pointer structure instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] SCSI core: better initialization for sdev->scsi_level
[SCSI] scsi_proc.c: display sdev->scsi_level correctly
[SCSI] megaraid_sas: update version and author info
[SCSI] megaraid_sas: return sync cache call with success
[SCSI] megaraid_sas: replace pci_alloc_consitent with dma_alloc_coherent in ioctl path
[SCSI] megaraid_sas: add bios_param in scsi_host_template
[SCSI] megaraid_sas: do not process cmds if hw_crit_error is set
[SCSI] scsi_transport.h should include scsi_device.h
[SCSI] aic79xx: remove extra newline from info message
[SCSI] scsi_scan.c: handle bad inquiry responses
[SCSI] aic94xx: tie driver to the major number of the sequencer firmware
[SCSI] lpfc: add PCI error recovery support
[SCSI] megaraid: pci_module_init to pci_register_driver
[SCSI] tgt: fix the user/kernel ring buffer interface
[SCSI] sgiwd93: interfacing to wd33c93
[SCSI] wd33c93: Fast SCSI with WD33C93B
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
Documentation/kernel-docs.txt update.
arch/cris: typo in KERN_INFO
Storage class should be before const qualifier
kernel/printk.c: comment fix
update I/O sched Kconfig help texts - CFQ is now default, not AS.
Remove duplicate listing of Cris arch from README
kbuild: more doc. cleanups
doc: make doc. for maxcpus= more visible
drivers/net/eexpress.c: remove duplicate comment
add a help text for BLK_DEV_GENERIC
correct a dead URL in the IP_MULTICAST help text
fix the BAYCOM_SER_HDX help text
fix SCSI_SCAN_ASYNC help text
trivial documentation patch for platform.txt
Fix typos concerning hierarchy
Fix comment typo "spin_lock_irqrestore".
Fix misspellings of "agressive".
drivers/scsi/a100u2w.c: trivial typo patch
Correct trivial typo in log2.h.
Remove useless FIND_FIRST_BIT() macro from cardbus.c.
...
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Fix the various misspellings of "agressive", as well as a couple
other things on the same lines while we're there.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This field is no longer used by the core IDE code so fix ide-{disk,floppy}
drivers to keep openers count in the driver specific objects and remove
it from ide-{cd,scsi,tape} drivers (it was write-only).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
there's a USB mass storage device which exists in two version. One
reports the correct size and the other does not. Apart from that they
are identical and cannot be told apart. Here's a heuristic based on the
empirical finding that drives have even sizes.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch will affect the CDB in INQUIRY commands sent to LUNs above 0
when LUN-0 reports a scsi_level of 0; the LUN bits will no longer be set
in the second byte of the CDB. This is as it should be. Nevertheless,
it's possible that some wacky device might be adversely affected. I doubt
anyone will complain...
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch (as833) fixes the "SCSI revision" output for
/proc/scsi/scsi. If the scsi_level value is 0 (UNKNOWN), we want it
to show up as "0", not "ffffffff".
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
FW does not support SYNCHRONIZE_CACHE cmd. FW flush cache on its own.
So, we just return success from the megasas_queue_command.
Signed-off-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replaced pci_alloc_consistent with dma_alloc_coherent from the ioctl path.
This is to avoid situations where ioctl fails for lack of memory
(when system under heavy stress).
Signed-off-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Checks if hw_crit_error is set.
If it is set, we donot process commands.
Checks added in megasas_queue_command and command completion routines.
Signed-off-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This extra newline character introduces a completely empty line in dmesg as
the calling function itself adds a newline.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A particular USB device has been reporting short inquiry lengths. The
SCSI code cannot operate properly unless we get an inquiry length of
36 or above (because of the way we parse vendor and product), so
assume at least 36 bytes are valid even if the device reports fewer.
This is wrong, but it's no worse than what we're doing now (using the
garbage beyond the last reported valid byte).
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The sequencer firmware file has both a string (currently showing
V17/10c6) and a number (currently set to 1.1). It has become apparent
that Adaptec may issue sequencer firmware in the future which could be
incompatible with the current driver. Therefore, the driver will be
tied to the particular major number of the firmware (i.e. the current
driver will load any 1.x firmware). Additionally, the driver will print
out both the ascii string and the major number, so with this pach the
current firmware will print out
aic94xx: Found sequencer firmware version 1.1 (V17/10c6)
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds PCI Error recovery support to the
Emulex Lightpulse Fibrechannel (lpfc) SCSI device driver.
Lightly tested at this point, works.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: Bino.Sebastian@Emulex.Com
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patches fixes two bugs in the scsi target infrastructure's
user/kernel interface.
- It wrongly assumes that the ring buffer size of the interface (64KB)
is larger than or equal to the system page size. This patch sets the
ring buffer size to PAGE_SIZE if the system page size is larger.
- It uses PAGE_SIZE in the header file exported to userspace. This
patch removes it.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
1) sgiwd93 used to switch off asynchronous mode on the wd33c93, discarding
any "nosync"-requests from the commandline.
But we need to allow "nosync"-requests for selected devices, for example
the Pioneer DVD305S.
(For the curious: this device accepts the SDTR from wd33c93 and success-
fully sends inquiry data in sync mode, but after the data phase in the
inquiry command does an unexpected disconnect, seemingly sending no
"status" or "command complete". Forcing async transfers makes it work
together flawlessly with the wd33c93. Of course, preferable would be, to
implement wd33c93's "resume command" stuff, but that probably will not
come soon.)
2) Maximize benefit from the preceding Fast SCSI patch for wd33c93 by passing
the higher input-clock frequency explicitely. To be applied after the
mentioned wd33c93 patch.
Signed-off-by: peter fuerst <post@pfrst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Attached are patches, which help to utilize more of the WD33C93B SCSI
controller's capabilities.
1) Added/changed all the necessary code to enable Burst Mode DMA. Only
Single Byte DMA was used before.
2) Added/changed all the necessary code to enable Fast-10 SCSI transfers.
3) The original driver inadvertently used a transfer period of 1000-800ns
(the lowest possible transfer rate) for asynchronous data transfers,
instead of the (configurable) default period intended for this purpose,
if the target responded to a SDTR not with a Reject-message, but with
a zero-SDTR. This issue was fixed.
Moreover, in case of a Reject the driver used the default-period's
initialization-value instead of its (maybe smaller) current value. The
missing assignment was added.
4) The driver's commandline- and proc-file-interface was augmented to
handle the new options properly.
The WD33C93 manual, found at
http://www.datasheet.in/datasheet-html/W/D/3/WD33C93B_WesternDigital.pdf.html,
was very helpful.
Signed-off-by: peter fuerst <post@pfrst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The semantic effect of insert_at_head is that it would allow new registered
sysctl entries to override existing sysctl entries of the same name. Which is
pain for caching and the proc interface never implemented.
I have done an audit and discovered that none of the current users of
register_sysctl care as (excpet for directories) they do not register
duplicate sysctl entries.
So this patch simply removes the support for overriding existing entries in
the sys_sysctl interface since no one uses it or cares and it makes future
enhancments harder.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Corey Minyard <minyard@acm.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (97 commits)
[SCSI] zfcp: removed wrong comment
[SCSI] zfcp: use of uninitialized variable
[SCSI] zfcp: Invalid locking order
[SCSI] aic79xx: use dma_get_required_mask()
[SCSI] aic79xx: fix bracket mismatch in unused macro
[SCSI] BusLogic: Replace 'boolean' by 'bool'
[SCSI] advansys: clean up warnings
[SCSI] 53c7xx: brackets fix in uncompiled code
[SCSI] nsp_cs: remove old scsi code
[SCSI] aic79xx: make ahd_match_scb() static
[SCSI] DAC960: kmalloc->kzalloc/Casting cleanups
[SCSI] scsi_kmap_atomic_sg(): check that local irqs are disabled
[SCSI] Buslogic: local_irq_disable() is redundant after local_irq_save()
[SCSI] aic94xx: update for v28 firmware
[SCSI] scsi_error: Fix lost EH commands
[SCSI] aic94xx: Add default bus reset handler
[SCSI] aic94xx: Remove TMF result code munging
[SCSI] libsas: Add an LU reset mechanism to the error handler
[SCSI] libsas: Don't BUG when connecting two expanders via wide port
[SCSI] st: fix Tape dies if wrong block size used, bug 7919
...
Simplify the few instances where a call to "get_zeroed_page()" is closely
followed by an unnecessary call to memset() to clear that page.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: chas williams <chas@cmf.nrl.navy.mil>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace appropriate pairs of "kmem_cache_alloc()" + "memset(0)" with the
corresponding "kmem_cache_zalloc()" call.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Roland McGrath <roland@redhat.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: Joel Becker <Joel.Becker@oracle.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As originally noted by Frederic Temporelli, the aic79xx supports 64
bit addressing, but the initialization code of the driver is wrong: it
tests the available memory size instead of testing the maximum
available memory address.
This patch uses the correct dma_get_required_mask() macros to
determine the correct addressing method.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Xavier Bru <xavier.bru@bull.net>
CC: Frederic Temporelli <frederic.temporelli@bull.net>
cosmetic fixes
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-tc:
[EISA] EISA registration with !CONFIG_EISA
[TC] pmagb-b-fb: Convert to the driver model
[TC] dec_esp: Driver model for the PMAZ-A
[TC] mips: pmag-ba-fb: Convert to the driver model
[TC] defxx: TURBOchannel support
[TC] TURBOchannel support for the DECstation
[TC] MIPS: TURBOchannel resources off-by-one fix
[TC] MIPS: TURBOchannel update to the driver model
This is a set of changes that converts the PMAZ-A support to the driver model.
The use of the driver model required switching to the hotplug SCSI
initialization model, which in turn required a change to the core NCR53C9x
driver. I decided not to break all the frontend drivers and introduced an
additional parameter for esp_allocate() to select between the old and the new
model. I hope this is OK, but I would be fine with converting NCR53C9x to the
new model unconditionally as long as I do not have to fix all the other
frontends (OK, perhaps I could do some of them ;-) ).
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix typecast warnings and switch from check_region to request_region
(akpm: Ken and Jeffrey Phillips Freeman <jeffreyfreeman@syncleus.com> are
possible advansys testers)
Signed-off-by: Ken Witherow <ken@krwtech.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The KM_BIO_SRC_IRQ kmap slot must be taken with local irqs disabled. Add a
check into scsi for this.
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
These changes work compatibly with the old V17 firmware
Contribution:
Ed Chim <ed_chim@adaptec.com>
Gilbert Wu <gilbert_wu@adaptec.com>
Change Log:
1. Use dword instead of qword to display the value of Connection
State register for debug purpose.
2. There are some registers location of AIC94xx chip has been changed
according to the new V28 firmware. The patch has redefined the register
location and provided initialization.
3. The new sequencer firmware v28 for Aic94xx SAS/SATA Linux open
source device driver can be downloaded from
http://www.adaptec.com/NR/exeres/35B611BC-9789-4B5B-82C6-85A2CCA8A46A.htm
Signed-off-by: Gilbert Wu <gilbert_wu@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] sd: udev accessing an uninitialized scsi_disk field results in a crash
[SCSI] st: A MTIOCTOP/MTWEOF within the early warning will cause the file number to be incorrect
[SCSI] qla4xxx: bug fixes
[SCSI] Fix scsi_add_device() for async scanning
If an EH command times out today, the LLDD's abort handler
will be called to abort the command. It is assumed that this
completes successfully, which can result in the command getting
completed later resulting in an oops. Improve the current
implementation by escalating all the way to host reset if
necessary in order to clean up the EH command.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In asd_initiate_ssp_tmf, the TMF result code is replaced with
TMF_RESP_FUNC_FAILED except when the TMF returns a result code immediately.
However, TMFs can return result codes via an ESCB... yet these codes are
also replaced with "FAILED". The only values that can fall into that case
are TMF_* codes anyway, so get rid of this code where COMPLETE and SUCCESS
are turned into FAILED. This also lets us propagate those TMF_* codes up
to the caller.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
After discussion with andmike and dougg, it seems that the purpose of
eh_device_reset_handler is to issue LU resets, and that
eh_bus_reset_handler would be a more appropriate place for a phy reset.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
libsas: Don't BUG when connecting two expanders via wide port
When a device is connected to an expander, the discovery process goes through
sas_ex_discover_dev to figure out what's attached to the phy. If it is the
case that the phy being discovered happens to be the second phy of a wide link
to an expander, that discover_dev function will incorrectly call
sas_ex_discover_expander, which creates another sas_port and tries to attach the
other sas_phys to the new port, thus triggering a BUG. The correct thing to do is
to check the other ex_phys of the expander to see if there's a sas_port for this
sas_phy, and attach the sas_phy to the existing sas_port.
This is easily triggered if one enables the phys of a wide port between
expanders one by one.
This second version of the patch fixes a small regression in the case where
all the phys show up at once and we accidentally try to attach to a port
that hasn't been created yet.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Thu, 1 Feb 2007, Andrew Morton wrote:
> On Thu, 1 Feb 2007 15:34:29 -0800
> bugme-daemon@bugzilla.kernel.org wrote:
>
> > http://bugzilla.kernel.org/show_bug.cgi?id=7919
> >
> > Summary: Tape dies if wrong block size used
> > Kernel Version: 2.6.20-rc5
> > Status: NEW
> > Severity: normal
> > Owner: scsi_drivers-other@kernel-bugs.osdl.org
> > Submitter: dmartin@sccd.ctc.edu
> >
> >
> > Most recent kernel where this bug did *NOT* occur: 2.6.17.14
> >
> > Other Kernels Tested and Results:
> >
> > OK 2.6.15.7
> > OK 2.6.16.37
> > OK 2.6.17.14
> > BAD 2.6.18.6
> > BAD 2.6.18-1.2869.fc6
> > BAD 2.6.19.2 +
> > BAD 2.6.20-rc5
> >
> > NOTE: 2.6.18-1.2869.fc6 is a Fedora modified kernel, all others are from kernel.org
> >
...
> > Steps to reproduce:
> > Get a Adaptec AHA-2940U/UW/D / AIC-7881U card and a tape drive,
> > install a recent kernel
> > set the tape block size - mt setblk 4096
> > read from or write to tape using wrong block size - tar -b 7 -cvf /dev/tape foo
> >
Write does not trigger this bug because the driver refuses in fixed block
mode writes that are not a multiple of the block size. Read does trigger
it in my system.
The bug is not associated with any specific HBA. st tries to do direct i/o
in fixed block mode with reads that are not a multiple of tape block size.
The patch in this message fixes the st problem by switching to using the
driver buffer up to the next close of the device file in fixed block mode
if the user asks for a read like this.
I don't know why the bug has surfaced only after 2.6.17 although the st
problem is old. There may be another bug in the block subsystem and this
patch works around it. However, the patch fixes a problem in st and in
this way it is a valid fix.
This patch may also fix the bug 7900.
The patch compiles and is lightly tested.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sd_probe() calls class_device_add() even before initializing the
sdkp->device variable. class_device_add() eventually results in the user mode
udev program to be called. udev program can read the the allow_restart
attribute of the newly created scsi device. This is resulting in a crash as
the show function for allow_restart (i.e sd_show_allow_restart) returns the
attribute value by reading the sdkp->device->allow_restart variable. As the
sdkp->device is not initialized before calling the user mode hotplug helper,
this results in a crash.
The patch below solves it by calling class_device_add() only after the
necessary fields in the scsi_disk structure are initialized properly.
Signed-off-by: Nagendra Singh Tomar <nagendra_tomar@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
1) If the device reports an uncorrectable MEDIUM ERROR, such
as SK MEDIUM ERROR, ASC UNRECOVERED READ ERR, AMNF DATA
FIELD or RECORD NOT FOUND, then: In scsi_check_sense()
return SUCCESS so as to not retry -- the error is
uncorrectable -- this speeds up total processing time.
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Extracted the MEDIUM ERROR piece and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since, mailbox commands are executed in a synchronous
manner, there is no need to have a separate spinlock
primitive to protect data/register access shared by callers.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As ISP24xx firmware can return a CS_DATA_UNDERRUN completion
status when the storage has returned a
SAM_STAT_TASK_SET_FULL scsi-status.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Non-ISP24xx cards must have a loop-id in order to query host
statistics.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Limit assignments via qla2x00_model_name[] array to HBA
subsystem vendor IDs equal to QLogic.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Previous work to add asynchronous-scsi-scanning support
(d19044c32b) caused peculiar
semantic changes when no cabling was attached to the HBA
whereby unneeded and intrusive 'error-handling' would take
place due to the initial link state being unset.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Similarly to previous LOGO requests on non-24xx hardware,
perform an implicit-LOGO as to avoid the potential 2 *
R_A_TOV delay which can result during an explicit-LOGO
request.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This includes BIOS, EFI, FCODE and firmware versions.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
No restriction should be placed on the IRQ number assigned
to a given ISP. Original code incorrectly assumed a
non-zero IRQ number assignment by the system. In these
circumstances the proper freeing of the IRQ (via free_irq())
would not take place.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
What DMA for 16bit pcmcia card, anyway? We never do request_dma()
there and ->dma_channel never changes since initialization to -1.
IOW, that call is dead code.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes a duplicate device id from the IPR driver. Based on
the ipr.h file, I'm not so sure this was intended to be a duplicate, and
if so, the .h file should be modified to use the proper sub-device id
instead.
This was pointed out to me by Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Set allow_restart=1 for all SAS disks so that they are spun up when needed.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Register libsas's default device reset code with the scsi.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch moves the code that handles SAS failures out of the main EH
function and into a separate function. It also detects commands that have
no sas_task (i.e. they completed, but with error data) and sends them into
scsi_error for processing. This allows us to handle SCSI errors (and
enables auto-spinup as a side effect) instead of dropping them on the
floor and falling into an infinite loop. It also requires the
implementation of a device reset function, which the SAS failure code has
been modified to employ for REQ_DEVICE_RESET.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Export a couple of functions from scsi_error that are needed to handle
failed SCSI commands from the SAS EH.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
make exports GPL and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Get rid of: "warning: ignoring return value of sysfs_create_link..."
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sas_rphy_delete does two things: it removes the sas_rphy from the transport
layer and frees the sas_rphy. This can be broken down into two functions,
sas_rphy_remove and sas_rphy_free; sas_rphy_remove is of interest to
sas_discover_root_expander because it calls functions that require
sas_rphy_add as a prerequisite and can fail (namely sas_discover_expander).
In that case, sas_discover_root_expander needs to be able to undo the effects
of sas_rphy_add yet leave the job of freeing the sas_rphy to the caller of
sas_discover_root_expander.
This patch also removes some unnecessary code from sas_discover_end_dev
to eliminate an unnecessary cycle of sas_notify_lldd_gone/found for SAS
devices, thus eliminating a sas_rphy_remove call (and fixing a race condition
where a SCSI target scan can come in between the gone and found call).
It also moves the sas_rphy_free calls into sas_discover_domain and
sas_ex_discover_end_dev to complement the sas_rphy_allocation via
sas_get_port_device.
This patch does not change the semantics of sas_rphy_delete.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently, sas_form_port checks the given asd_sas_phy's sas_phy to see if
there's already a port attached. If so, the SAS addresses of the port and
the phy are compared to determine if we need to detach from the port
because the addresses don't match or if we can stop; the SAS address stored
in the sas_port reflects whatever device _was_ attached to the port/phy, and
the SAS address stored in the sas_port reflects whatever device we just
discovered. As written, the code detaches from the port if the addresses
_do_ match, and prints an error if they do _not_ match. I believe this to
be incorrect, as it seems more logical to keep the port if the addresses
match (i.e. the phy was reset but the device didn't change), and detach it
they do not (i.e. the device changed).
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn,
Take the expose_physicals flag and allow the user to select default (physicals
available via /dev/sg), exposed (physicals available via /dev/sd for
experimental reasons) and hidden (physicals blocked from all access). This
expands the functionality of the previous expose_physicals insmod parameter
which was added to support some experimental configurations.
Signed-off-by Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn,
Replace all if/else packet formations with platform function calls. This is in
recognition of the proliferation of read and write packet types, and in the
need to migrate to up-and-coming packets for new products.
Signed-off-by Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn,
Add in the NEMER/ARK physical register mapping, represented in up and coming
products currently under test at Adaptec.
Signed-off-by Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn,
Replace all if/else communication transports with a platform function call.
This is in recognition of the need to migrate to up-and-coming transports.
Currently the Linux driver does not support two available communication
transports provided by our products, these will be added in future patches, and
will expand the platform function set.
Signed-off-by Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since the pci_block_user_cfg_access API was modified to track
block/unblocks, it was discovered that the ipr driver had a
path through its code (in PCI error recovery) which would unblock
when not previously blocked.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Don't fail initialization of an adapter if the PCI-X registers
cannot be found since it may be a PCI-E adapter.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since ipr handles dynamic ids, it must handle driver_data
not being set, so remove the current usage of driver_data
so it can be used for other things in future patches.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
fix typos and bump version number
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Alexis Bruemmer <alexisb@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Wed, 24 Jan 2007, Andrew Morton wrote:
> On Mon, 22 Jan 2007 13:07:20 -0800
> bugme-daemon@bugzilla.kernel.org wrote:
>
> > http://bugzilla.kernel.org/show_bug.cgi?id=7864
> >
> > Summary: A MTIOCTOP/MTWEOF within the early warning will cause
> > the file number to be incorrect
> > Kernel Version: 2.6.19.2
> > Status: NEW
> > Severity: low
> > Owner: io_scsi@kernel-bugs.osdl.org
> > Submitter: ce_reisinger@yahoo.com
> >
> >
> > Write records to a SCSI tape until a write fails with a ENOSPC (you have reached
> > early warning.
> > Now perform a:
> > struct mtget before, after;
> > ioctl(fd, MTIOCGET, &before);
> > struct mtop mtop = { MTWEOF, 1 };
> > ioctl(fd, MTIOCTOP, &mtop);
> > ioctl(fd, MTIOCGET, &after);
> >
> > Check the value of mt_fileno in the before and after structures. Notice the
> > after is 2 greater then the before.
> >
> > The problem appears to be in the block of code starting at line 2817 in st.c.
> > This block is entered because the drive did return a CHECK CONDITION with NO
> > SENSE and the SENSE_EOM bit set. At lines 2824/5 the fileno is incremented. But
> > it has already been increased by the number of filemarks requested by the
> > MTIOCTOP. I believe that the residue count in the sense data should be
> > subtracted from fileno, not a increment as is done.
> >
>
> Thanks. Could you please send us a tested patch to fix these things, as
> per http://www.zip.com.au/~akpm/linux/patches/stuff/tpp.txt ?
>
The analysis is basically correct and explains the bug. According to the
SCSI standards, the sense code is NO SENSE or RECOVERED ERROR in case
writing filemark(s) succeeds. If it fails (partly or completely) the sense
code is VOLUME OVERFLOW. The patch below is tested to fix the case when
one filemark is successfully written after the EOM early warning. It
should also fix the case at real EOM but this has not been tested.
Carl, thanks for reporting the bug and providing the analysis for the fix.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The included patch fixes the following issues:
1. qla3xxx/qla4xxx co-existence issue which can result in a lockup
when qla3xxx driver is unloaded, or when ifdown; ifup is performed on
one of the interfaces correponding to qla3xxx. This is because qla4xxx
HBA supports one ethernet and iscsi interfaces per port. Both iscsi
and ethernet interfaces share the same state machine. The problem has
to do with synchronizing access to the state machine in the event of a
reset
2. mutex_lock() is sometimes not followed by mutex_unlock() prior to
invoking a msleep() in qla4xxx_mailbox_command()
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I had thought that all drivers which didn't call scsi_scan_host()
called scsi_scan_target(). Some, such as sbp2, mptsas and libata-scsi,
call scsi_add_device() or __scsi_add_device(). We just need to wait
for the currently executing async scans to complete first. This is the
same code that's in scsi_scan_target(), except that we have to return
an error instead of void when we're declining to scan at all.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The EH should fall into I_T recovery (and potentially stronger
remedies) if ABORT TASK fails.
Signed-off-by: Alexis Bruemmer <alexisb@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Track sas_ha_struct state so that we ignore events that come in while
we're shutting things down.
Signed-off-by: Malahal Naineni <malahal@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert the phy port locks to use irq spinlocks.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add the necessary hooks to the aic94xx driver to support the asynchronous SCSI
device scan infrastructure.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Allowing the phy reset controls to be world-triggerable does not seem like
a terribly good idea because SAS devices can be disrupted (and ATA devices
are really disrupted) by a phy reset. By default only root should be able
to do things like that.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Extend the use of the DDB lock to include all DDB accesses, because
DDB updates now occur from multiple threads. This fixes the SMP timeout
problems that we were occasionally seeing with a x260, because the
controller got confused when the DDBs got corrupted.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Ed Chim of Adaptec informs us that the DDB registers need to be zeroed at
initialization time and that some SCB initializations need to happen even if
we don't use the SCB.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The vmalloc() blob holding the sequencer firmware wasn't being released at
module unload time, which resulted in a memory leak.
Signed-off-by: Alexis Bruemmer <alexisb@us.ibm.com>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Now that task aborts and device port resets are done by the EH, we can
remove all the code that set up workqueues and such and simply call
sas_task_abort and let libsas figure things out.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sas_task_abort() should simply abort the upper-level SCSI command and wait
until the error handler to send the actual ABORT TASK command. By
deferring things to the EH we simplify the concurrency coordination and
eliminate some race conditions. Note that sas_task_abort has a few hooks
to handle libsas internal commands properly too.
Also rename do_sas_task_abort to __sas_task_abort just in case we really
want to abort the task *right now* and we don't have a scsi_cmnd attached
to the command. This is a hook for libata internal commands to abort.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When a SAS LLDD needs to request a device port reset, it needs to have all
commands aborted before it can reset the port. Since commands are put on
the EH's list in the order that they were queued, the LLDD can set a "need
reset" flag in the last task to be aborted so that the EH can reset the
port after all commands are aborted.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This flag is no longer necessary because we push tasks to be aborted into
the EH as soon as we possibly can, and let the SCSI EH code take care of
the coordination for which this flag was used.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In this driver, TMF_QUERY_TASK translates to QUERY_SSP_TASK. The
sequencer, it seems, is perfectly happy sending us a SSP response, which
this function promptly "converts" into TMF_RESP_FUNC_FAILED. This leads to
the SAS EH making bad decisions based on bad data, so we should not perform
the conversion in this case.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The aic94xx module has a parameter that looks like it should set
lldd_max_execute_num in the sas_ha, but it never sets this value. Either
we should set it or remove the parameter. This allows us to enable task
collector mode for this driver, though it is still off by default.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If we use task collector mode, we can end up destroying the task collector
thread before we release the ports, which is bad if a port release causes
a disk I/O (such as cache flushing).
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Every so often, a scsi_cmnd will time out, and the libsas timeout handler
will discover that the scsi_cmnd does not have a sas_task attached to it.
This can happen in two cases: (1) the scsi_cmnd actually made it through
libsas to the HBA and is now going through scsi_done, or (2) the
scsi_cmnd has been held up (host lock, slab alloc, etc) and libsas has
not yet attached a sas_task. In both cases, it is safe to ask SCSI for
more time to process the command via EH_RESET_TIMER; we cannot blindly
return EH_HANDLED because if (2) happens, we could end up calling
scsi_done while another CPU is heading towards sas_queuecommand, which
causes slab corruption when sas_task_done updates the freed scsi_cmnd.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch lets a user arbitrarily enable or disable a phy via sysfs.
Potential applications include shutting down a phy to replace one
lane of wide port, and (more importantly) providing a method for the
libata SATL to control the phy.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On a system with many SAS targets, it appears possible that a scsi_cmnd
can time out without ever making it to the SAS LLDD or at the same time
that a completion is occurring. In both of these cases, telling the
LLDD to abort the sas_task makes no sense because the LLDD won't know
about the sas_task; what we really want to do is to increase the timer.
Note that this involves creating another sas_task bit to indicate
whether or not the task has been sent to the LLDD; I could have
implemented this by slightly redefining SAS_TASK_STATE_PENDING, but
this way seems cleaner.
This second version amends the aic94xx portion to set the
TASK_AT_INITIATOR flag for all sas_tasks that were passed to
lldd_execute_task.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sas_get_port_device assigns a rphy to a domain device in anticipation
of finding a disk. When a discovery error occurs in
sas_discover_{sata,sas,expander}*, however, we need to clean up that
rphy and the port device list so that we don't GPF. In addition, we
need to check the result of the second sas_notify_lldd_dev_found.
This patch seems ok on a x260, x366 and x206m.
This patch fixes up sas_expander.c separately because jejb has some
cleanup patches of his own that are a prerequisite.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sas_get_port_device assigns a rphy to a domain device in anticipation
of finding a disk. When a discovery error occurs in
sas_discover_{sata,sas,expander}*, however, we need to clean up that
rphy and the port device list so that we don't GPF. In addition, we
need to check the result of the second sas_notify_lldd_dev_found.
This patch seems ok on a x260, x366 and x206m.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Removed spin_unlock_irq()/spin_lock_irq() pairs surrounding
starget_for_each_device() calls.
As Matthew W. pointed out, starget_for_each_device() can be called under
a spinlock being held.
The change has been tested and verified on qla2xxx.ko module.
Thanks Matthew W. and Hisashi H. for help.
Signed-off-by: Andrew Vasquez <Andrew.vasquez@qlogic.com>
Signed-off-by: Seokmann Ju <Seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hi,
Minor typo ...
In my first iteration of patches (that got merged), the
BLIST_ATTACH_PQ3 actually had the value 0x800000, but that
got changed later to avoid conflicts. This piece must have
been overlooked.
You could obviously do something like %x and then add the
bitflags, but that looks overkill for something that does
not tend to change.
Please merge.
(Patch applied against latest 2.6.20rc version that I tested.)
From: Kurt Garloff <kurt@garloff.de>
Subject: [SCSI SCAN] Fix logging message for PQ3 devices
The blacklist flags BLIST_ATTACH_PQ3 has value 0x1000000,
not 0x800000.
Signed-off-by: Kurt Garloff <garloff@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
More megaraid kernel-doc fixes.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Sumant Patro <sumantp@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
kernel-doc modifications:
- change "@param var" notation to @var;
- change function/description separator from ':' to '-';
- change var/description separator from '-' to ':';
- fix a few doc. typos;
- don't use kernel-doc /** lead-in when the doc. block is not kernel-doc;
- use Linux common */ ending comment format instead of **/;
- use correct function parameter names;
- place function parameters immediately after the function short description;
- place kernel-doc immediately before its function or macro;
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Sumant Patro <sumantp@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
1. Changes in Initialization to fix kdump failure.
Send SYNC command on loading.
This command clears the pending commands in the adapter
and re-initialize its internal RAID structure.
Without this change, megaraid driver either panics or fails to
initialize the adapter during kdump's second kernel boot
if there are pending commands or interrupts from other devices
sharing the same IRQ.
2. Authors email-id domain name changed from lsil.com to lsi.com.
Also modified the MODULE_AUTHOR to megaraidlinux@lsi.com
Signed-off-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
After discussions in the thread titled:
[PATCH] scsi_debug: illegal blocking memory allocation
here is a patch containing the discussed fix and some other
fixes and additions. The patch is against lk 2.6.20-rc3 .
The version is bumped to 1.81 .
ChangeLog:
- Change several GFP_KERNEL allocations to GFP_ATOMIC
as they can be called from queuecommand() context
- check above allocation returns and if out of memory
report DID_REQUEUE in two cases, DID_NO_CONNECT in
another, and fail slave configure() in another
- add support for WRITE BUFFER command
- add aborted_command error injection support
(opts mask 0x10), similar mechanism to
recovered_error injection.
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_retry_command only has a single caller, so there is no point
in having this function. Additionally the memset of the sense
buffer it does is entirely superflous as scsi_request_fn already
calls scsi_init_cmd_errh to perform this memset before the command
is reissued.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The D700 needs the burst length setting to the previous 53c700 default
of 8 otherwise it will be effectively disabled.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a patch, which allows not only disabling bursting but to specify
different burst lenghts. This feature is needed to get the 53c700 driver
working for the onboard SCSI controller of SNI RM machines, which only
work reliably with a 4 word burst length.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Setting .ConfigBase and .Present is now done at the pcmcia core.
The driver cleanup missed a few places where the driver did set .Present
to PRESENT_OPTION and later to the values from the CIS. Setting to
PRESENT_OPTION now overrides the values from the CIS. So just remove
those lines.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeremy caught a bug in the qla1280 driver where it didn't set the
residual value correctly.
Signed-off-by: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update domain name change from lsil.com to lsi.com.
Change module author to megaraidlinux@lsi.com
Signed-off-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The attached patch updates the 3ware 8000 driver:
- Free irq handler in __tw_shutdown().
- Turn on RCD bit for caching mode page.
- Serialize reset code.
Signed-off-by: Adam Radford <linuxraid@amcc.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sr_block_ioctl() should proceed to SCSI ioctls if cdrom_ioctl()
returns -ENOSYS. However it tested for ENOSYS instead of -ENOSYS
rendering all SCSI ioctls other than GET_IDLUN and GET_BUS_NUMBER
inaccessible. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add kmalloc failure check and fix the loop on error path. Without the
patch pool element at index [0] will not be freed.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update drivers/scsi/aacraid/linit.c and Documentation/scsi/aacraid.txt
file with the current list of
adapters supported by the aacraid driver. Deprecated a few adapters that
never shipped, corrected a
few and added new adapters that matched the family code support. No
functional changes to the driver.
No side effects.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Yanling Qi, noted that when the sense data length of
a check-condition is greater than 0x7f (127), senselen = (data[0] << 8)
| data[1] will become negative. It causes different kinds of panics from
GPF, spin_lock deadlock to spin_lock recursion.
We were also swapping this value on big endien machines.
This patch fixes both issues by using be16_to_cpu().
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch cures two run together printk messages in iSCSI
driver.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The return value of crypto_alloc_hash() should be checked by
IS_ERR().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The transition from crypto_digest_*() to the crypto_hash_*() family
introduced a bug into the data digest calculation: crypto_hash_update() is
called with the number of S/G elements instead of the S/G lists data size.
Signed-off-by: Arne Redlich <arne.redlich@xiranet.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Apparently no ATAPI CD/DVD actually supports REPORT LUNS (in spite of
claiming scsi-3 compliance, where it's mandatory) and worse, some
crash or flake out on being sent the command. This may actually be
due to a conflict between SPC and MMC with MMC not listing REPORT LUNS
as mandatory. The same standards conflict exists for RBC as well.
Fix all of this by reversing the blacklists for CDROM and RBC devices
(i.e. now they have to have the BLIST_REPORTLUNS2 flag set even if the
inquiry data returns scsi-3 compliance).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rather than a direct call, as was done in the case of a
RISC-paused state within the ISP24xx interrupt handler.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original code would incorrectly use non-24xx code-paths.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Disable subsequent GPSC queries if Fabric Management services do
not support the operation.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Alan Stern
Thomas Bogendoerfer
Alan Cox
Salyzyn, Mark
Christoph Hellwig
Tejun Heo
James Bottomley
Alexey Dobriyan
James Bottomley
FUJITA Tomonori
Ed Lin
Brian King
James Smart
David S. Miller
Linus Torvalds
Russell King
Ralf Baechle
Bartlomiej Zolnierkiewicz
Michael Opdenacker
Thomas Gleixner
Randy Dunlap
Andrew Vasquez
Olaf Hering
Amol Lad
walter harms
Paul Mackerras
Martin Habets
Guennadi Liakhovetski
Christoph Hellwig
Adrian Bunk
David Milburn
Matthias Kaehlcke
vignesh.babu@wipro.com
Geert Uytterhoeven
Roman Zippel
Michael Schmitz
Michael Ellerman
Jean Delvare
Alexander E. Patrakov
Stephen Rothwell
David Miller
Jens Axboe
Andrew Morton
Greg Kroah-Hartman
Patrick McHardy
Arnaldo Carvalho de Melo
Michael Tokarev
Zachary Amsden
Bastian Blank
Robert Jennings
Robert Jennings
Bernhard Walle
Robert P. J. Day
Henne
Richard Lary
Anton Blanchard
Richard Knutsson
Mark Haverkamp
Pete Wyckoff
Malahal Naineni
James Bottomley
Mike Christie
Martin K. Petersen
Joerg Dorchain
Linas Vepstas
Tobias Klauser
Matthew Wilcox
Uwe Kleine-König
Oliver Neukum
Sumant Patro
Rolf Eike Beer
peter fuerst
Eric W. Biederman
Tim Schmielau
Arjan van de Ven
Hannes Reinecke
Al Viro
Maciej W. Rozycki
Mariusz Kozlowski
Ken Witherow
Michal Piotrowski
Andrew Morton
Jiri Kosina
Wu, Gilbert
Darrick J. Wong
Kai Makisara
Eric Moore
Nagendra Singh Tomar
Luben Tuikov
Seokmann Ju
Lalit Chandivade
Alexis Bruemmer
David C Somayajulu
Kurt Garloff
Douglas Gilbert
Daniel Ritz
Jes Sorensen
adam radford
Meelis Roos
Akinobu Mita
Arne Redlich