The CFI information read from AT49BV6416 lists the erase regions in the
wrong order, causing problems when trying to erase or update the first
or last 64KiB block.
Work around this by inverting the "top boot" flag, which will
effectively reverse the order of the erase regions.
This chip is obsolete, but it's used in some existing designs.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The patch adds support for NAND flashes connected to GPIOs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds TopBottom detection for most Macronix chips with CFI V1.0.
The main purpose of this patch is to add detection of the MX29LV400C B
used on the LaCie Ethernet Disk mini V2 NAS.
It detects the following parts correctly:-
MX28F640C3B T
MX29LV002C B
MX29LV002NC B
MX29LV004C T
MX29LV400C T/B
MX29LV800C T/B
MX29LV160C T/B
MX29SL800C T/B
MX29SL802C T/B
It detects the following uniform part as bottom but it should work
correctly:-
MX29LV040C
For T parts it causes the erase block table to be reversed correctly.
For other parts it avoids the bogus "Assuming top" message.
It does not detect the following correctly:-
MX28F640C3B B
MX29LV002C T
MX29LV002NC T
MX29LV004C B
MX29SL400C T/B
MX29SL402C T/B
If desired I could supply a more complicated patch to handle these as
well.
Only the MX29LV400C B has been physically tested; others were checked
against their data sheets.
Signed-off-by: Christopher Moore <moore@free.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
After choosing new c->nextblock, don't leave the wbuf offset field
occasionally pointing at the start of the next physical eraseblock.
This was causing a BUG() on NOR-ECC (Sibley) flash, where we start
writing after the cleanmarker.
Among other this fix should cover write buffer offset adjustment
after flushing the last page of an eraseblock.
Signed-off-by: Alexander Belyakov <abelyako@googlemail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This makes the driver erase a block when it doesn't find any
existing saved log messages which is safer than assuming the
flash was already erased.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a magic number to logged kernel oops messages so that they
can be more accurately detected rather than just having to rely
on the sequence number. This also allows easier detection of
saved crashes by userspace.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix an off by one error in the mtdoops driver
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Make the parameter names of jffs2_compress() in its comments match with the
actual implementation
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Several Renesas SuperH CPU has FLCTL. The FLCTL support NAND Flash.
This driver support SH7723.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The functions that write the OOB info (on hardware ECC only) use the
HW_SYNDROME method.
This is not correct : the start position is "pos = eccsize + chunk" and
should be eccsize. So, the standard (nand_write_oob_std) function should
be used. This patch corrects this by using NAND_ECC_HW instead of
NAND_ECC_HW_SYNDROME.
This has only been tested on small pages nand flash.
(if anyone can test it on large pages that would be great).
kernel version : 2.6.27-rc2 (current git mtd-2.6)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Removed the Kconfig associated with 'NDFC NanD Flash Controller'.
We can't enable !CONFIG_PPC_MERGE so there is no way to enable
this. Additionally the code needs to get updated for arch/powerpc.
For the time being lets just remove the Kconfig option so we can
actually remove CONFIG_PPC_MERGE.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch extends the FSL UPM NAND driver from Anton Vorontsov to
support hardware which does not have the R/B pin of the NAND chip
connected, like the TQM8548 module:
- The OF_GPIO dependency has been removed from the Kconfig option
because GPIO is not needed. The relevant gpio_* function are then
stubbed out in <linux/gpio.h>.
- It re-introduces the chip-delay property to define an appropriate
maximum delay time (tR) required for read operations. The binding
will be documented in a separate patch.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
- Get rid of fsl,wait-pattern and fsl,wait-write. I think this isn't
chip-specific, and we should always do waits. I saw one board that
didn't need fsl,wait-pattern, but I assume this was the exception
that proves the rule;
- Get rid of chip-delay. Today there are no users for this, and if
anyone really need this they should push the OF bindings beforehand;
- Now flash chips should be child nodes of the FSL UPM NAND controller;
- Implement OF partition parsing.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch makes debugging a missconfigured UBI a bit easier
by providing the needed information in the boot log.
Signed-off-by: Deepak Saxena <dsaxena@laptop.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When iterating over a chain in reverse (oldest block first), this
patch correctly marks the PUtable[] entry of the second to last erase
block of a chain as BLOCK_NIL, regardless of whether or not it can
format the last block successfully. Before, the second to last block
was only marked as pointing to BLOCK_NIL if INFTL_formatblock()
succeeded on the last block of the chain, which could potentially
result in an infinite loop if the block was worn out and refused to
format.
Signed-off-by: Daniel Rosenthal <danielrosenthal@acm.org>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
...since it only probes that
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Now that the needed helpers are exported, it becomes a nice simple
switch over. Closes#9420
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
.... so that they can be used by MTD map drivers. Lets us close#9420
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The patch fixes CFI issue with multipartitional devices leading to the
set of errors or even deadlock. The problem is CFI FL_SYNCING state race
with flash operations (e.g. erase suspend). It is reproduced by running
intensive writes on one JFFS2 partition and simultaneously performing
mount/unmount cycle on another partition of the same chip.
Signed-off-by: Alexander Belyakov <abelyako@googlemail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In case of error, the function add_volume returns an ERR pointer. The
result of IS_ERR, which is supposed to be used in a test as it is, is
here checked to be less than zero, which seems odd. We suggest to
replace this test by a simple IS_ERR test.
A simplified version of the semantic match that finds this problem is
as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@def0@
expression x;
position p0;
@@
x@p0 = add_volume(...)
@protected@
expression def0.x,E;
position def0.p0;
position p;
statement S;
@@
x@p0
... when != x = E
if (!IS_ERR(x) && ...) {<... x@p ...>} else S
@unprotected@
expression def0.x,E;
identifier fld;
position def0.p0;
position p != protected.p;
@@
x@p0
... when != x = E
* x@p->fld
// </smpl>
Signed-off-by: Julien Brunel <brunel@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Some chips require a RESET after power-up (e.g. Micron MT29FxGxxxxx).
The first command sent is NAND_CMD_READID.
Issue a NAND_CMD_RESET in nand_scan_ident before reading the device id.
Tested with an MT29F4G08AAC.
Signed-off-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Very occasionally, (about one in a million) read operations are
ongoing after the timeout has expired. So, retry three times
while the ongoing bit remains set.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for the integrated NAND flash controller of the
i.MX2 and i.MX3 family. It is tested on MX27 but should work on MX3
aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Minor patch to help debugging of NAND detection.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch moves some attributes out from the platform data into the
dynamically created nand device. This results into a cleaner interface
and allows to use constant pxa3xx_nand_flash definitions.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch marks some attributes as 'const' which are set only once and
never be modified by the driver. There are some changes in parameter
list and variable declarations too which mark them as 'const'.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a MTD_NAND_PXA3xx_BUILTIN configuration variables which
allows to disable usage of builtin flash-type table. Not enabling this
option saves some space in the generated driver.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds 'flash' and 'num_flash' attributes to the platform data.
There was added code in the driver to iterate across these attributes in the
detect-flash routine. This is done similarly to the existing method
which uses a 'builtin_flash_types' field.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch moves the exported datastructures from the pxa3xx_nand.c driver
into the <mach/pxa3xx_nand.h> header. This is a plain movement without
any modification of the attributes.
This is the first one of a set of patches which:
* allows to specify used NAND flash in the platform code and allows to turn
off the old way to specify NAND characteristics in the driver. This way did
not worked well as these characteristics depend on the platform and can not be
derived from NAND id alone.
E.g. some NAND chips share the same ID (e.g. K9K8G08U0A and K9NBG08U5A) but
have different timings (which are written in the common driver currently and
must be modified there).
* adds 'const' annotations at various places
Further patches will be sent to the mtd-list.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Semun Lee <semun.lee@samsung.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Not used anywhere yet, but this complements the existing plain
'insert_resource()' functionality with a version that can expand the
resource we are adding in order to fix up any conflicts it has with
existing resources.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pulling the ethernet cable on a 2.6.27-rc system with NFS mounts
currently leads to an ongoing flood of soft lockup detector backtraces
for all tasks blocked on the NFS mounts when the hickup takes
longer than 120s.
I don't think NFS problems should be all that noisy.
Luckily there's a reasonably easy way to distingush this case.
Don't report task softlockup warnings for tasks in TASK_KILLABLE
state, which is used by the network file systems.
I believe this patch is a 2.6.27 candidate.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit a2bd7274b4.
It wasn't really right to begin with (there's a better fix for the
problem with e820 reservations clashing with PCI BAR's pending), but it
also actually causes more regressions, so it should be reverted even
before the better fix is finalized.
Rafael reports that this commit broke AHCI detection, and thus causes
the kernel to not boot on his quad core test box.
Reported-and-bisected-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: David Witbrodt <dawitbro@sbcglobal.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When changing the sample rate, the CMI8788's master clock output becomes
unstable for a short time. The AK4396 needs the master clock to do SPI
writes, so writing to an AK4396 control register directly after a sample
rate change will garble the value. In our case, this leads to the DACs
being misconfigured to I2S sample format, which results in a wrong
output level and horrible distortions on samples louder than -6 dB.
To fix this, we need to wait until the new master clock signal has
become stable before doing SPI writes.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin arch: Fix PM building on BF52x: No ROTWE on BF52x, add USBWE
Blackfin arch: sram: use 'unsigned long' for irqflags
Blackfin arch: let PCI depend on BROKEN
Blackfin arch: move include/asm-blackfin header files to arch/blackfin
Blackfin arch: fix bug - MPU crashes under stress
Blackfin arch: Fix bug - when to rmmod the L1_module, it stucks and then reboot the board.
Blackfin arch: dont actually need to muck with EMAC_SYSTAT for BF52x for demuxing
Blackfin arch: Add MTD Partitions for MTD_DATAFLASH, increase max SPI SCLK
