Fixed Alignment should match open parenthesis from checkpatch
Signed-off-by: Scott Matheina <scott@matheina.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed Alignment should match open parenthesis checkpatch CHECK
Signed-off-by: Scott Matheina <scott@matheina.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed Alignment should match open parenthesis checkpatch CHECK
Signed-off-by: Scott Matheina <scott@matheina.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the space coding styles issues complained by checkpatch.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This should fix the indentation issues found by checkpatch.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need for a vchiq_2835.h with its 2 local defines.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch tries to make the kernel thread names of vchiq a little
bit more self explaining and look closer to the existing ones:
slot handler: VCHIQ-%d -> vchiq-slot/%d
recycle thread: VCHIQr-%d -> vchiq-recy/%d
sync thread: VCHIQs-%d -> vhciq-sync/%d
keep-alive thread: VCHIQka-%d -> vchiq-keep/%d
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes issues reported by checkpatch.pl about preferred
kernel types.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The quota_spinlock is only local. So make it static.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This variable is assigned a value, but never used. So remove it.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The functions vchiq_dump_shared_state() and vchiq_is_connected() are only
used locally. So make them static.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is never used, so we could remove it.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes absence of braces on last arm of statement, identified by
checkpatch
Signed-off-by: Scott Matheina <scott@matheina.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes Alignment should match open parenthesis in checkpatch
Signed-off-by: Scott Matheina <scott@matheina.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This issue is caught by checkpatch.pl and is related to the following
warning:
- CHECK: Please don't use multiple blank lines
Signed-off-by: Emmanuil Chatzipetru <chatzi.emanuel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This issue is caught by checkpatch.pl and is related to the following
warning:
- CHECK: spaces preferred around that '/' (ctx:VxV)
Signed-off-by: Emmanuil Chatzipetru <chatzi.emanuel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dcon_was_irq(); should return a boolean value if PMIO_Rx50[6] is either
set or unset, which is evaluated in the first return statement. Therefore,
the following return statement is redundant and thus, removed.
Signed-off-by: Emmanuil Chatzipetru <chatzi.emanuel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This issue is caught by checkpatch.pl and is related to the following
warning:
- CHECK: Alignment should match open parenthesis
Signed-off-by: Emmanuil Chatzipetru <chatzi.emanuel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following warnings:
line over 80 characters
Signed-off-by: Abdul Rauf <abdulraufmujahid@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following checks:
Please don't use multiple blank lines
Signed-off-by: Abdul Rauf <abdulraufmujahid@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 0fd972a7d9 ("module: relocate module_init
from init.h to module.h"), including module.h will do and
init.h is also thrown in.
Signed-off-by: Cheah Kok Cheong <thrust73@gmail.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver's COMEDI "auto-attach" handler `db2k_auto_attach()` calls
`db2k_find_boardinfo()` to find an element of our board information
array `db2k_boardtypes[]` that matches the probed PCI device. The
driver's PCI device table matches several boards in the DaqBoard/2000
series that match a single PCI vendor and device ID combination.
`db2k_find_boardinfo()` uses the probed PCI device's subvendor and
subdevice IDs to find the matching board information, returning `NULL`
for no match.
Change the driver's PCI device table `db2k_pci_table[]` to match
supported PCI vendor, device, subvendor and subdevice IDs, and set the
`.driver_data` member of each element to the index of the matching
element of `db2k_boardtypes[]`. That index gets passed through to the
COMEDI auto-attach handler `db2k_auto_attach()`. Use it to index
directly into `db2k_boardtypes[]` instead of calling
`db2k_find_boardinfo()` to find the match.
Use array index designators in the initializer of `db2k_boardtypes[]`.
Use enumerated constants defined by new type `enum db2k_boardids` to
name the board type indices.
The `id` member of `struct db2k_boardtype` is no longer used, so remove
it. Also remove the subdevice ID macros `DB2K_SUBSYSTEM_IDS2` and
`DB2K_SUBSYSTEM_IDS4` as the subdevice IDs are now specified as numbers
in the PCI device table. Remove `db2k_find_boardinfo()` as it is no
longer used.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The COMEDI device name strings are currently set to "ids2" for the
DaqBoard/2000, and to "ids4" for the DaqBoard/2001. Change them to
"daqboard2000" and "daqboard2001" respectively. (The COMEDI driver name
string is also "daqboard2000".)
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver supports DaqBoard/2000 and DaqBoard/2001. DaqBoard/2000 has 2
AO channels, but DaqBoard/2001 has 4 AO channels. The driver currently
only supports 2 AO channels, but supporting 4 channels is just a case of
setting the `n_chan` member of the COMEDI subdevice to 4 instead of 2.
Add a new boolean flag member `has_2_ao` to `struct db2k_boardtype` to
be set to `true` if the board only has 2 AO channels. Set this to
`true` in the element of `db2k_boardtypes[]` that corresponds to the
DaqBoard/2000. Use it in `db2k_auto_attach()` to initialize the number
of AO channels to 2 or 4, as appropriate.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the undesignated initializers for each element of
`db2k_boardtypes[]` with an equivalent designated initializer for ease
of future maintenance.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a consistent prefix of `db2k_` or `DB2K_` for identifiers. The
existing prefixes `DAQBOARD2000_` and `daqboard2000_` are a bit on the
lengthy side.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `card` member of `struct daqboard2000_private` and the enumerated
constant `card_daqboard_2000` are not used. Remove them.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to an old GPL'ed driver at
<ftp://ftp.mccdaq.com/downloads/iotech_software/DaqBoard_1000_2000_Series/Linux_driver_kernelv2.4.x/>,
The CPLD status register can be checked to make sure that it is ready to
accept the next 16-bit word of FPGA firmware data, but that doesn't work
on older versions of the CPLD, where a simple delay should be used
between successive writes. The current version of the Comedi driver
just uses a delay between successive writes. Change it to check for the
newer CPLD in the `daqboard2000_load_firmware()`, and change the
firmware word writing function `daqboard2000_write_cpld()` to wait for
the status bit (`DB2K_CPLD_STATUS_TXREADY`, previously called
`DB2K_CPLD_TXDONE`) to be set for newer CPLD, or just delay for older CPLD.
Return an error if it times out waiting for the status bit.
The wait for the `DB2K_CPLD_STATUS_TXREADY` status bit to be set is
performed by new function `daqboard2000_wait_cpld_txready()`, which
returns 0 if the status bit is set within 100 microseconds, or
`-ETIMEDOUT` if not.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to an old, GPL'ed Linux driver at
<ftp://ftp.mccdaq.com/downloads/iotech_software/DaqBoard_1000_2000_Series/Linux_driver_kernelv2.4.x/>,
after programming the FPGA, the General Purpose Input (USERI) of the PLX
PCI-9080 should go high shortly after a valid FPGA bitstream has been
loaded. Add a new function `daqboard2000_wait_fpga_programmed()` to
wait for that, performing up to 200 checks over a 20 ms period (this is
loosely based on `pollFPGADone()` in the above-mentioned old driver).
Return 0 if the FPGA appears to have loaded successfully, or
`-ETIMEDOUT` if it runs out of checks. Call it from the firmware
loading callback `daqboard2000_load_firmware()` after writing the
firmware to the FPGA to check it is programmed successfully.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`daqboard2000_write_cpld()` currently returns 1 on success, or 0 on
failure. Change it to return 0 on success, or `-EIO` on failure.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`daqboard2000_poll_cpld()` waits for a specified status bit in the CPLD
status register to be set, giving up after 50 tries over a period of
about 5 milliseconds. It returns 1 if the status bit is set, otherwise
0. It is only ever called to check the "INIT" status bit. Replace it
with new function `daqboard2000_wait_cpld_init()`, which returns 0 if
the "INIT" status bit becomes set within 50 tries, or `-ETIMEDOUT` if
not set within 50 tries. The firmware loading callback
`daqboard2000_load_firmware()` may return the error result from
`daqboard2000_wait_cpld_init()` if it has used up all its firmware
loading attempts and that was the last error.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Firmware files for DAQBoard/2000 have a header, which is skipped,
followed by a sequence of FPGA configuration bytes to be programmed in
pairs. The FPGA configuration bytes start with the sequence 0xff, 0x20.
Make the firmware loading callback function
`daqboard2000_load_firmware()` return an error `-EINVAL` if the FPGA
start sequence is not found, or the remaining length is not a multiple
of 2.
The firmware loading callback tries to program the FPGA up to 3 times
until it succeeds or it has tried too many times. Currently, it
searches for the FPGA start sequence in the firmware data each time
through the retry loop. Change it to adjust the start position and
length before entering the loop.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CPLD status and data registers used to load firmware are 16 bits
wide. Use the type `u16` to represent data and status values instead of
`int`.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Daqboard/2000 uses a write-only data register and a read-only status
register in a pre-programmed CPLD device to program the main firmware on
the board. Both registers are at offset 0x1000 from PCI BAR 2. Define
macros for the register offsets. Rename the existing macros for the
status register values for consistency. (Two status bits are defined,
but the driver code only seems to use one of them.)
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Daqboard/2000 uses a PLX PCI-9080 chip to interface with the PCI
bus. The "daqboard2000" driver uses the PCI-9080 "CNTRL" register to
perform various tasks, but defines its own macros for the register
values. Use the macros from "plx9080.h" instead. The various functions
that change the CNTRL register just wiggle individual bits up and down,
but they ignore the current register value - the old macros defined the
full value to be written to the register. Change them to read and
modify the register value.
Also remove a read of the CNTRL register in `daqboard2000_auto_attach()`
where the value is just thrown away, as it seems to serve no purpose
there (such as flushing PCI writes).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
checkpatch.pl complained about two unnecessary blank lines after an
opening '{' in prism2mib.c. Those were removed in order to get rid
of those warnings.
There are more issues pointed out by checkpatch.pl. Those require
additional work to be done.
Signed-off-by: Markus Buettner <markus.buettner@fau.de>
Signed-off-by: Artur Wasinger <artur.wasinger@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changed file permission to octal style,
Can't use __ATTR_RW() as the handler is in standard format.
Found using checkpatch
Signed-off-by: Derek Robson <robsonde@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Connect to the highest rssi with the required SSID in the shadow
table if the connection criteria is based only on the SSID.
For the first matching SSID, an index to the table is saved.
Later the index is updated if matching SSID has a higher
RSSI value than the last saved index.
However if decision is made based on BSSID, there is only one match
in the table and corresponding index is used.
changes in v2:
initialize sel_bssi_idx to UINT_MAX.
Combine two checks for identifying
sel_bssi_idx value for a SSID.
Signed-off-by: Aditya Shankar <aditya.shankar@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following warnings:
Block comments should align the * on each line
Signed-off-by: Abdul Rauf <abdulraufmujahid@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These redundant unlocks of visornic_devdata.priv_lock would result in
the RHEL 7.2 guests hanging during service partition recovery testing.
__Testing__
* An scp of a large file was started from a remote host TO the RHEL 7.2
Linux guest.
* During the scp transfer, s-Par service partition recovery was forced
twice. After each occasion, I verified that the guest recovered
completely (all s-Par guest devices), and that the file transfer
resumed.
* Within the RHEL 7.2 guest environment, copied the large file to
another location in the local filesystem.
* During the copy, s-Par service partition recovery was again forced
twice. After each occasion, I verified that the guest recovered
completely (all s-Par guest devices), and that the copy resumed.
* An scp of the new copy of the large file was started FROM the RHEL 7.2
guest to a remote host.
* During the scp transfer, s-Par service partition recovery was forced
twice. After each occasion, I verified that the guest recovered
completely (all s-Par guest devices), and that the file transfer
resumed.
* Used cmp to verify that the large file had successfully survived the
round-trip without becoming corrupted.
Signed-off-by: Tim Sell <Timothy.Sell@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove errant -EIOs that prevent us from calling either
netif_start_queue() or napi_disable().
Signed-off-by: David Binder <david.binder@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moves the call to napi_enable() before the call to init_rcv_bufs(),
ensuring that messages are not put into the receive queue until the guest
is ready to receive interrupts.
Signed-off-by: David Binder <david.binder@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Scott Matheina
Stefan Wahren
Yamanappagouda Patil
Emmanuil Chatzipetru
Abdul Rauf
Cheah Kok Cheong
Ian Abbott
Markus Buettner
Derek Robson
Aditya Shankar
Tim Sell
David Binder