Removed serdev_device_open/close functions from qca_open/close as
they are called in hci_uart_register_device() and
hci_uart_unregister_device() functions.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The barriers are unneeded; wait_woken() and woken_wake_function()
already provide us with the required synchronization: remove them
and document that we're relying on the (implicit) synchronization
provided by wait_woken() and woken_wake_function().
Signed-off-by: Andrea Parri <andrea.parri@amarulasolutions.com>
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
(the parameters in question are mark and flow_flags)
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(the parameters in question are mark and flow_flags)
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta controller can handle speeds up to 2500Mbps on the SGMII
interface. This relies on serdes configuration, the lane must be
configured at 3.125Gbps and we can't use in-band autoneg at that speed.
The main issue when supporting that speed on this particular controller
is that the link partner can send ethernet frames with a shortened
preamble, which if not explicitly enabled in the controller will cause
unexpected behaviours.
This was tested on Armada 385, with the comphy configuration done in
bootloader.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tonghao Zhang says:
====================
net: vhost: improve performance when enable busyloop
This patches improve the guest receive performance.
On the handle_tx side, we poll the sock receive queue
at the same time. handle_rx do that in the same way.
For more performance report, see patch 4
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves the guest receive performance.
On the handle_tx side, we poll the sock receive queue at the
same time. handle_rx do that in the same way.
We set the poll-us=100us and use the netperf to test throughput
and mean latency. When running the tests, the vhost-net kthread
of that VM, is alway 100% CPU. The commands are shown as below.
Rx performance is greatly improved by this patch. There is not
notable performance change on tx with this series though. This
patch is useful for bi-directional traffic.
netperf -H IP -t TCP_STREAM -l 20 -- -O "THROUGHPUT, THROUGHPUT_UNITS, MEAN_LATENCY"
Topology:
[Host] ->linux bridge -> tap vhost-net ->[Guest]
TCP_STREAM:
* Without the patch: 19842.95 Mbps, 6.50 us mean latency
* With the patch: 37598.20 Mbps, 3.43 us mean latency
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out generic busy polling logic and will be
used for in tx path in the next patch. And with the patch,
qemu can set differently the busyloop_timeout for rx queue.
To avoid duplicate codes, introduce the helper functions:
* sock_has_rx_data(changed from sk_has_rx_data)
* vhost_net_busy_poll_try_queue
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the VHOST_NET_VQ_XXX as a subclass for mutex_lock_nested.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the way that lock all vqs
at the same, to lock them one by one. It will
be used for next patch to avoid the deadlock.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After sk_state exposed, we can get in which state this retransmission
occurs. That could give us more detail for dignostic.
For example, if this retransmission occurs in SYN_SENT state, it may
also indicates that the syn packet may be dropped on the remote peer due
to syn backlog queue full and then we could check the remote peer.
BTW,SYNACK retransmission is traced in tcp_retransmit_synack tracepoint.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trival cleanup, list_move_tail will implement the same function that
list_del() + list_add_tail() will do. hence just replace them.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trival cleanup, list_move_tail will implement the same function that
list_del() + list_add_tail() will do. hence just replace them.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov says:
====================
net: bridge: convert bool options to bits
A lot of boolean bridge options have been added around the net_bridge
structure resulting in holes and more importantly different cache lines
that need to be fetched in the fast path. This set moves all of those
to bits in a bitfield which resides in a hot cache line thus reducing
the size of net_bridge, the number of holes and the number of cache
lines needed for the fast path.
The set is also sent in preparation for new boolean options to avoid
spreading them in the structure and making new holes.
One nice side-effect is that we avoid potential race conditions by using
the bitops since some of the options were bits being directly set in
parallel risking hard to debug issues (has_ipv6_addr).
Before:
size: 1184, holes: 8, sum holes: 30
After:
size: 1160, holes: 3, sum holes: 7
Patch 01 is a trivial style fix
Patch 02 adds the new options bitfield and converts the vlan boolean
options to bits
Patches 03-08 convert the rest of the boolean options to bits
Patch 09 re-arranges a few fields in net_bridge to further reduce size
v2: patch 09: remove the comment about offload_fwd_mark in net_bridge and
leave it where it is now, thanks to Ido for spotting it
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Further reduce the size of net_bridge with 8 bytes and reduce the number of
holes in it:
Before: holes: 5, sum holes: 15
After: holes: 3, sum holes: 7
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the last remaining bool option to a bit thus reducing the overall
net_bridge size further by 8 bytes.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the neigh_suppress_enabled option to a bit.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the rest of the mcast options to bits. It also packs
the mcast options a little better by moving multicast_mld_version to an
existing hole, reducing the net_bridge size by 8 bytes.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert mcast disabled to an option bit and while doing so convert the
logic to check if multicast is enabled instead. That is make the logic
follow the option value - if it's set then mcast is enabled and vice versa.
This avoids a few confusing places where we inverted the value that's being
set to follow the mcast_disabled logic.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert group_addr_set internal bridge opt to a bit.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No functional change, convert of nf_call_[ip|ip6|arp]tables to bits.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge options have usually been added as separate fields all over the
net_bridge struct taking up space and ending up in different cache lines.
Let's move them to a single bitfield to save up space and speedup lookups.
This patch adds a simple API for option modifying and retrieving using
bitops and converts the first user of the API - the bridge vlan options
(vlan_enabled and vlan_stats_enabled).
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we have a mix of opening brackets on new lines and on the same
line, let's move them all on the same line.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/net: updates 2018-09-26
please apply one more series of cleanups and small improvements for qeth
to net-next. Note that one patch needs to touch both af_iucv and qeth, in
order to untangle their receive paths.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdevice is always available, apply any carrier state changes to it
without caching them.
On a STARTLAN event (ie. carrier-up), defer updating the state to
qeth_core_hardsetup_card() in the subsequent recovery action.
Also remove the carrier-state checks from the xmit routines. Stopping
transmission on carrier-down is the responsibility of upper-level code
(eg see dev_direct_xmit()).
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If qeth_check_ipa_data() consumed an event, there's no point in
processing it further. So drop it early, and make the surrounding code
a tiny bit more readable.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull one level of checking up into qeth_send_control_data_cb(), and
clean up an else-after-return. No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have no code that is waiting for these events, so just drop them when
they arrive.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. tracing iob->rc makes no sense when it hasn't been modified by the
callback,
2. the qeth_dbf_list is declared with LIST_HEAD, which also initializes
the list,
3. the ccwgroup core only calls the thaw/restore callbacks if the gdev
is online, so we don't have to check for it again.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cdev-to-card translation walks through two layers of drvdata,
with no locking or refcounting (where eg. the ccwgroup core only
accesses a cdev's drvdata while holding the ccwlock).
This might be safe for now, but any careless usage of the helper has the
potential for subtle races and use-after-free's. Luckily there's only
one occurrence where we _really_ need it (in qeth_irq()), for any other
user we can just pass through an appropriate card pointer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to remove the CARD_FROM_CDEV calls in the iob callbacks.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When not using the CQ, this allows us avoid the second skb queue walk
in qeth_release_skbs().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was presumably left over from back when qeth recursed into
dev_queue_xmit().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To match the use of __skb_queue_purge(), also make the skb's enqueue in
qeth_fill_buffer() lockless.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch attempts to untangle the TX and RX code in qeth from
af_iucv's respective HiperTransport path:
On the TX side, pointing skb_network_header() at the IUCV header
means that qeth_l3_fill_af_iucv_hdr() no longer needs a magical offset
to access the header.
On the RX side, qeth pulls the (fake) L2 header off the skb like any
normal ethernet driver would. This makes working with the IUCV header
in af_iucv easier, since we no longer have to assume a fixed skb layout.
While at it, replace the open-coded length checks in af_iucv's RX path
with pskb_may_pull().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_core_probe_device() sets the gdev's drvdata, but doesn't reset it
on a subsequent error. Move the (re-)setting around a bit, so that it
happens symmetrically on allocating/freeing the qeth_card struct.
This is no actual problem, as the ccwgroup core will discard the gdev
on a probe error. But from qeth's perspective the gdev is an external
resource, so it's best to manage it cleanly.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device initialization code usually first loads a subdriver
(via qeth_core_load_discipline()), and then runs its setup() callback.
If this fails, it rolls back the load via qeth_core_free_discipline().
qeth_core_free_discipline() expects the options.layer attribute to be
initialized, but on error in setup() that's currently not the case.
Resulting in misbalanced symbol_put() calls.
Fix this by setting options.layer when loading the subdriver.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate declaration and initialization of a static variable.
While at it reduce its scope in qeth_core_load_discipline(), and simplify
the return logic accordingly.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the raw values are fixed due to their use in a sysfs attribute,
we can still use the proper QETH_DISCIPLINE_* enum within the driver.
Also move the initialization into qeth_set_initial_options(), along with
all other user-configurable fields.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Local variable 'autoneg' doesn't even exist:
drivers/net/phy/marvell.c: In function 'm88e1121_config_aneg':
drivers/net/phy/marvell.c:468:25: error: 'autoneg' undeclared (first use in this function); did you mean 'put_net'?
if (phydev->autoneg != autoneg || changed) {
^~~~~~~
Fixes: d6ab933647 ("net: phy: marvell: Avoid unnecessary soft reset")
Reported-by:Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: ed842faeb2 ("bridge: suppress nd pkts on BR_NEIGH_SUPPRESS ports")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-09-25
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Allow for RX stack hardening by implementing the kernel's flow
dissector in BPF. Idea was originally presented at netconf 2017 [0].
Quote from merge commit:
[...] Because of the rigorous checks of the BPF verifier, this
provides significant security guarantees. In particular, the BPF
flow dissector cannot get inside of an infinite loop, as with
CVE-2013-4348, because BPF programs are guaranteed to terminate.
It cannot read outside of packet bounds, because all memory accesses
are checked. Also, with BPF the administrator can decide which
protocols to support, reducing potential attack surface. Rarely
encountered protocols can be excluded from dissection and the
program can be updated without kernel recompile or reboot if a
bug is discovered. [...]
Also, a sample flow dissector has been implemented in BPF as part
of this work, from Petar and Willem.
[0] http://vger.kernel.org/netconf2017_files/rx_hardening_and_udp_gso.pdf
2) Add support for bpftool to list currently active attachment
points of BPF networking programs providing a quick overview
similar to bpftool's perf subcommand, from Yonghong.
3) Fix a verifier pruning instability bug where a union member
from the register state was not cleared properly leading to
branches not being pruned despite them being valid candidates,
from Alexei.
4) Various smaller fast-path optimizations in XDP's map redirect
code, from Jesper.
5) Enable to recognize BPF_MAP_TYPE_REUSEPORT_SOCKARRAY maps
in bpftool, from Roman.
6) Remove a duplicate check in libbpf that probes for function
storage, from Taeung.
7) Fix an issue in test_progs by avoid checking for errno since
on success its value should not be checked, from Mauricio.
8) Fix unused variable warning in bpf_getsockopt() helper when
CONFIG_INET is not configured, from Anders.
9) Fix a compilation failure in the BPF sample code's use of
bpf_flow_keys, from Prashant.
10) Minor cleanups in BPF code, from Yue and Zhong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses devm_ioremap_resource() which is only available when
CONFIG_HAS_IOMEM is set, make the driver depend on this config option.
User mode Linux does not have CONFIG_HAS_IOMEM set and the driver was
failing on this architecture.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: phy: Eliminate unnecessary soft
This patch series eliminates unnecessary software resets of the PHY.
This should hopefully not break anybody's hardware; but I would
appreciate testing to make sure this is is the case.
Sorry for this long email list, I wanted to make sure I reached out to
all people who made changes to the Marvell PHY driver.
Thank you!
Changes since RFT:
- added Tested-by tags from Wang, Dongsheng, Andrew, Chris and Clemens
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The BMCR.RESET bit on the Marvell PHYs has a special meaning in that
it commits the register writes into the HW for it to latch and be
configured appropriately. Doing software resets causes link drops, and
this is unnecessary disruption if nothing changed.
Determine from marvell_set_polarity()'s return code whether the register value
was changed and if it was, propagate that to the logic that hits the software
reset bit.
This avoids doing unnecessary soft reset if the PHY is configured in
the same state it was previously, this also eliminates the need for a
m88e1111_config_aneg() function since it now is the same as
marvell_config_aneg().
Tested-by: Wang, Dongsheng <dongsheng.wang@hxt-semitech.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While consolidating the PHY reset in phy_init_hw() an unconditionaly
BMCR soft-reset I became quite trigger happy with those. This was later
on deactivated for the Generic PHY driver on the premise that a prior
software entity (e.g: bootloader) might have applied workarounds in
commit 0878fff1f4 ("net: phy: Do not perform software reset for
Generic PHY").
Since we have a hook to wire-up a soft_reset callback, just use that and
get rid of the call to genphy_soft_reset() entirely. This speeds up
initialization and link establishment for most PHYs out there that do
not require a reset.
Fixes: 87aa9f9c61 ("net: phy: consolidate PHY reset in phy_init_hw()")
Tested-by: Wang, Dongsheng <dongsheng.wang@hxt-semitech.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-09-25
This series contains updates to i40e and xsk.
Mariusz fixes an issue where the VF link state was not being updated
properly when the PF is down or up. Also cleaned up the promiscuous
configuration during a VF reset.
Patryk simplifies the code a bit to use the variables for PF and HW that
are declared, rather than using the VSI pointers. Cleaned up the
message length parameter to several virtchnl functions, since it was not
being used (or needed).
Harshitha fixes two potential race conditions when trying to change VF
settings by creating a helper function to validate that the VF is
enabled and that the VSI is set up.
Sergey corrects a double "link down" message by putting in a check for
whether or not the link is up or going down.
Björn addresses an AF_XDP zero-copy issue that buffers passed
from userspace to the kernel was leaked when the hardware descriptor
ring was torn down. A zero-copy capable driver picks buffers off the
fill ring and places them on the hardware receive ring to be completed at
a later point when DMA is complete. Similar on the transmit side; The
driver picks buffers off the transmit ring and places them on the
transmit hardware ring.
In the typical flow, the receive buffer will be placed onto an receive
ring (completed to the user), and the transmit buffer will be placed on
the completion ring to notify the user that the transfer is done.
However, if the driver needs to tear down the hardware rings for some
reason (interface goes down, reconfiguration and such), the userspace
buffers cannot be leaked. They have to be reused or completed back to
userspace.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Buslov says:
====================
Refactor classifier API to work with Qdisc/blocks without rtnl lock
Currently, all netlink protocol handlers for updating rules, actions and
qdiscs are protected with single global rtnl lock which removes any
possibility for parallelism. This patch set is a third step to remove
rtnl lock dependency from TC rules update path.
Recently, new rtnl registration flag RTNL_FLAG_DOIT_UNLOCKED was added.
Handlers registered with this flag are called without RTNL taken. End
goal is to have rule update handlers(RTM_NEWTFILTER, RTM_DELTFILTER,
etc.) to be registered with UNLOCKED flag to allow parallel execution.
However, there is no intention to completely remove or split rtnl lock
itself. This patch set addresses specific problems in implementation of
classifiers API that prevent its control path from being executed
concurrently. Additional changes are required to refactor classifiers
API and individual classifiers for parallel execution. This patch set
lays groundwork to eventually register rule update handlers as
rtnl-unlocked by modifying code in cls API that works with Qdiscs and
blocks. Following patch set does the same for chains and classifiers.
The goal of this change is to refactor tcf_block_find() and its
dependencies to allow concurrent execution:
- Extend Qdisc API with rcu to lookup and take reference to Qdisc
without relying on rtnl lock.
- Extend tcf_block with atomic reference counting and rcu.
- Always take reference to tcf_block while working with it.
- Implement tcf_block_release() to release resources obtained by
tcf_block_find()
- Create infrastructure to allow registering Qdiscs with class ops that
do not require the caller to hold rtnl lock.
All three netlink rule update handlers use tcf_block_find() to lookup
Qdisc and block, and this patch set introduces additional means of
synchronization to substitute rtnl lock in cls API.
Some functions in cls and sch APIs have historic names that no longer
clearly describe their intent. In order not make this code even more
confusing when introducing their concurrency-friendly versions, rename
these functions to describe actual implementation.
Changes from V2 to V3:
- Patch 1:
- Explicitly include refcount.h in rtnetlink.h.
- Patch 3:
- Move rcu_head field to the end of struct Qdisc.
- Rearrange local variable declarations in qdisc_lookup_rcu().
- Patch 5:
- Remove tcf_qdisc_put() and inline its content to callers.
Changes from V1 to V2:
- Rebase on latest net-next.
- Patch 8 - remove.
- Patch 9 - fold into patch 11.
- Patch 11:
- Rename tcf_block_{get|put}() to tcf_block_refcnt_{get|put}().
- Patch 13 - remove.
====================
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Balakrishna Godavarthi
Andrea Parri
Maciej Żenczykowski
Maxime Chevallier
David S. Miller
Tonghao Zhang
Yafang Shao
YueHaibing
zhong jiang
Nikolay Aleksandrov
Julian Wiedmann
Roopa Prabhu
Hauke Mehrtens
Florian Fainelli