The kernel crash was reported by Alexy. He was testing some feature
with private kernel, in which Alexy added some code in pci_pm_reset()
to read the CSR after writting it. The bug could be reproduced on
Fiber Channel card (Fibre Channel: Emulex Corporation Saturn-X:
LightPulse Fibre Channel Host Adapter (rev 03)) by the following
commands.
# echo 1 > /sys/devices/pci0004:01/0004:01:00.0/reset
# rmmod lpfc
# modprobe lpfc
The history behind the test case is that those additional config
space reading operations in pci_pm_reset() would cause EEH error,
but we didn't detect EEH error until "modprobe lpfc". For the case,
all the PCI devices on PCI bus (0004:01) were removed and added after
PE reset. Then the EEH devices would be figured out again based on
the OF nodes. Unfortunately, there were some child OF nodes under
PCI device (0004:01:00.0), but they didn't have attached PCI_DN since
they're invisible from PCI domain. However, we were still trying to
convert OF node to EEH device without checking on the attached PCI_DN.
Eventually, it caused the kernel crash as follows:
Unable to handle kernel paging request for data at address 0x00000030
Faulting instruction address: 0xc00000000004d888
cpu 0x0: Vector: 300 (Data Access) at [c000000fc797b950]
pc: c00000000004d888: .eeh_add_device_tree_early+0x78/0x140
lr: c00000000004d880: .eeh_add_device_tree_early+0x70/0x140
sp: c000000fc797bbd0
msr: 8000000000009032
dar: 30
dsisr: 40000000
current = 0xc000000fc78d9f70
paca = 0xc00000000edb0000 softe: 0 irq_happened: 0x00
pid = 2951, comm = eehd
enter ? for help
[c000000fc797bc50] c00000000004d848 .eeh_add_device_tree_early+0x38/0x140
[c000000fc797bcd0] c00000000004d848 .eeh_add_device_tree_early+0x38/0x140
[c000000fc797bd50] c000000000051b54 .pcibios_add_pci_devices+0x34/0x190
[c000000fc797bde0] c00000000004fb10 .eeh_reset_device+0x100/0x160
[c000000fc797be70] c0000000000502dc .eeh_handle_event+0x19c/0x300
[c000000fc797bf00] c000000000050570 .eeh_event_handler+0x130/0x1a0
[c000000fc797bf90] c000000000020138 .kernel_thread+0x54/0x70
The patch changes of_node_to_eeh_dev() and just returns NULL if the
passed OF node doesn't have attached PCI_DN.
Cc: stable@vger.kernel.org
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The EEH core is talking with the PCI device driver to determine the
action (purely reset, or PCI device removal). During the period, the
driver might be unloaded and in turn causes kernel crash as follows:
EEH: Detected PCI bus error on PHB#4-PE#10000
EEH: This PCI device has failed 3 times in the last hour
lpfc 0004:01:00.0: 0:2710 PCI channel disable preparing for reset
Unable to handle kernel paging request for data at address 0x00000490
Faulting instruction address: 0xd00000000e682c90
cpu 0x1: Vector: 300 (Data Access) at [c000000fc75ffa20]
pc: d00000000e682c90: .lpfc_io_error_detected+0x30/0x240 [lpfc]
lr: d00000000e682c8c: .lpfc_io_error_detected+0x2c/0x240 [lpfc]
sp: c000000fc75ffca0
msr: 8000000000009032
dar: 490
dsisr: 40000000
current = 0xc000000fc79b88b0
paca = 0xc00000000edb0380 softe: 0 irq_happened: 0x00
pid = 3386, comm = eehd
enter ? for help
[c000000fc75ffca0] c000000fc75ffd30 (unreliable)
[c000000fc75ffd30] c00000000004fd3c .eeh_report_error+0x7c/0xf0
[c000000fc75ffdc0] c00000000004ee00 .eeh_pe_dev_traverse+0xa0/0x180
[c000000fc75ffe70] c00000000004ffd8 .eeh_handle_event+0x68/0x300
[c000000fc75fff00] c0000000000503a0 .eeh_event_handler+0x130/0x1a0
[c000000fc75fff90] c000000000020138 .kernel_thread+0x54/0x70
1:mon>
The patch increases the reference of the corresponding driver modules
while EEH core does the negotiation with PCI device driver so that the
corresponding driver modules can't be unloaded during the period and
we're safe to refer the callbacks.
Cc: stable@vger.kernel.org
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have missed lots of situations where the PE hierarchy tree need
protection through the EEH global mutex. The patch fixes that for
those public APIs implemented in eeh_pe.c. The only exception is
eeh_pe_restore_bars() because it calls eeh_pe_dev_traverse(), which
has been protected by the mutex.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Function eeh_rmv_from_parent_pe() could be called by the path of
either normal PCI hotplug, or EEH recovery. For the former case,
we need purge the corresponding PE on removal of the associated
PE bus.
The patch tries to cover that by passing more information to function
pcibios_remove_pci_devices() so that we know if the corresponding PE
needs to be purged or be marked as "invalid".
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When EEH error happens on the PE whose PCI devices don't have
attached drivers. In function eeh_handle_event(), the default
value PCI_ERS_RESULT_NONE will be returned after iterating all
drivers of those PCI devices belonging to the PE. Actually, we
don't have installed drivers for the PCI devices. Under the
circumstance, we will remove the corresponding PCI bus of the PE,
including the associated EEH devices and PE instance. However,
we still need the information stored in the PE instance to do PE
reset after that. So it's unsafe to free the PE instance.
The patch introduces EEH_PE_INVALID type PE to address the issue.
When the PCI bus and the corresponding attached EEH devices are
removed, we will mark the PE as EEH_PE_INVALID. At later point,
the PE will be changed to EEH_PE_DEVICE or EEH_PE_BUS when the
corresponding EEH devices are attached again.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We don't need them anymore. The patch removes those functions.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, the PCI probe flags "PCI_PROBE_ONLY | PCI_REASSIGN_ALL_RSRC"
used on powernv platform. That means the platform has to do the PCI
resource assignment by itself.
The patch changes the PCI probe flag to "PCI_REASSIGN_ALL_RSRC" so
that the PCI core will do the resource assignment. Also, the I/O
and MMIO minimal alignment for P2P bridges have been configured
while doing fixup for the PHBs.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There're 2 arrays introduced to trace which PE has occupied the
corresponding resource (I/O or MMIO) segment. However, we didn't
allocate enough memory for them and that possiblly leads to PE
descriptor corruption.
The patch fixes that by allocating enough memory for those 2 arrays.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While the device driver or PCI core tries to enable PCI device, the
platform dependent callback "ppc_md.pcibios_enable_device_hook" will
be called to check if there has one associated PE for the PCI device.
If we don't have the associated PE for the PCI device, it's not allowed
to enable the PCI device. Unfortunately, there might have some cases
we have to enable the PCI device (e.g. P2P bridge), but the PEs have
not been created yet.
The patch handles the unfortunate cases. Each PHB (struct pnv_phb)
has one field "initialized" to trace if the PEs have been created
and configured or not. When the PEs are not available, we won't check
the associated PE for the PCI device to be enabled.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch introduces additional wrapper function to call the original
implementation so that the DMA can be configured for all existing PEs.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There're 2 types of PCI bus sensitive PEs: (A) The PE includes
single PCI bus. (B) The PE includes the PCI bus and all the subordinate
PCI buses, and the patch tries to assign I/O and MMIO resources
based on created PEs. Fortunately, we figured out unified scheme
to do resource assignment for all types of PCI bus based PEs according
to Ben's idea:
- Resource assignment based on PE from top to bottom.
- The soureces, either I/O or MMIO, of the PE are figured out
from the assigned PCI bus.
- The occupied resource by parent PE could possibilly be overrided
by children PEs.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The resource (I/O and MMIO) will be assigned on basis of PE from
top to bottom so that we can implement the trick here: the resource
that has been assigned to parent PE could be taken by child PE if
necessary.
The current implementation already has PE list per PHB basis, but
the list doesn't meet our requirment: tracing PE based on their
cration time from top to bottom. So the patch does rename for the
DMA based PE list and introduces the list to trace the PEs sequentially
based on their creation time.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Basically, there're 2 types of PCI bus sensitive PEs: (A) The PE
includes single PCI bus. (B) The PE includes the PCI bus and all
the subordinate PCI buses. At present, we'd like to put PCI bus
originated by PCI-e link to form PE that contains single PCI bus,
and the PCIe-to-PCI bridge will form the 2nd type of PE. We don't
figure out to detect PLX bridge yet. Once we can detect PLX bridge
some day, we have to put PCI buses originated from the downstream
port of PLX bridge to the 2nd type of PE.
The patch changes the original implementation for a little bit
to support 2 types of PCI bus sensitive PEs described as above.
Also, the function used to retrieve the corresponding PE according
to the given PCI device has been changed based on that because each
PCI device should trace the directly associated PE.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch convert different functions to take virtual page number
instead of virtual address. Virtual page number is virtual address
shifted right by VPN_SHIFT (12) bits. This enable us to have an
address range of upto 76 bits.
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Don't open code the same
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Merge Gavin patches from the PCI tree as subsequent powerpc
patches are going to depend on them
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* commit 'v3.6-rc5': (1098 commits)
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
ARM: gemini: fix the gemini build
...
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/rapidio/devices/tsi721.c
We unified the Freescale pci/pcie initialization by changing the fsl_pci
to a platform driver. In previous PCI code architecture the initialization
routine is called at board_setup_arch stage. Now the initialization is done
in probe function which is architectural better. Also It's convenient for
adding PM support for PCI controller in later patch.
Now we registered pci controllers as platform devices. So we combine two
initialization code as one platform driver.
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the dependency on PCI initialization for SWIOTLB initialization.
So that PCI can be initialized at proper time.
SWIOTLB is partly determined by PCI inbound/outbound map which is assigned
in PCI initialization. But swiotlb_init() should be done at the stage of
mem_init() which is much earlier than PCI initialization. So we reserve the
memory for SWIOTLB first and free it if not necessary.
All boards are converted to fit this change.
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support to disable and re-enable individual cores at runtime on
MPC85xx/QorIQ SMP machines. Currently support e500v1/e500v2 core.
MPC85xx machines use ePAPR spin-table in boot page for CPU kick-off. This
patch uses the boot page from bootloader to boot core at runtime. It
supports 32-bit and 36-bit physical address.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Do hardware timebase sync. Firstly, stop all timebases, and transfer the
timebase value of the boot core to the other core. Finally, start all
timebases.
Only apply to dual-core chips, such as MPC8572, P2020, etc.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale / iVeia P1022RDK reference board is a small-factor board
with a Freescale P1022 SOC. It includes:
1) 512 MB 64-bit DDR3-800 (max) memory
2) 8MB SPI serial flash memory for boot loader
3) Bootable 4-bit SD/MMC port
4) Two 10/100/1000 Ethernet connectors
5) One SATA port
6) Two USB ports
7) One PCIe x4 slot
8) DVI video connector
9) Audio input and output jacks, powered by a Wolfson WM8960 codec.
Unlike the P1022DS, the P1022RDK does not have any localbus devices,
presumably because of the localbus / DIU multiplexing restriction of
the P1022 SOC.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the Freescale P5040DS Reference Board ("Superhydra"), which
is similar to the P5020DS. Features of the P5040 are listed below, but
not all of these features (e.g. DPAA networking) are currently supported.
Four P5040 single-threaded e5500 cores built
Up to 2.4 GHz with 64-bit ISA support
Three levels of instruction: user, supervisor, hypervisor
CoreNet platform cache (CPC)
2.0 MB configures as dual 1 MB blocks hierarchical interconnect fabric
Two 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
support Up to 1600MT/s
Memory pre-fetch engine
DPAA incorporating acceleration for the following functions
Packet parsing, classification, and distribution (FMAN)
Queue management for scheduling, packet sequencing and
congestion management (QMAN)
Hardware buffer management for buffer allocation and
de-allocation (BMAN)
Cryptography acceleration (SEC 5.0) at up to 40 Gbps SerDes
20 lanes at up to 5 Gbps
Supports SGMII, XAUI, PCIe rev1.1/2.0, SATA Ethernet interfaces
Two 10 Gbps Ethernet MACs
Ten 1 Gbps Ethernet MACs
High-speed peripheral interfaces
Two PCI Express 2.0/3.0 controllers
Additional peripheral interfaces
Two serial ATA (SATA 2.0) controllers
Two high-speed USB 2.0 controllers with integrated PHY
Enhanced secure digital host controller (SD/MMC/eMMC)
Enhanced serial peripheral interface (eSPI)
Two I2C controllers
Four UARTs
Integrated flash controller supporting NAND and NOR flash
DMA
Dual four channel
Support for hardware virtualization and partitioning enforcement
Extra privileged level for hypervisor support
QorIQ Trust Architecture 1.1
Secure boot, secure debug, tamper detection, volatile key storage
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The patch implements ppc_md.pcibios_window_alignment for powernv
platform so that the resource reassignment in PCI core will be
done according to the I/O and memory alignment returned from
powernv platform. The alignments returned from powernv platform
is closely depending on the scheme for PE segmenting. Besides,
the patch isn't useful for now, but the subsequent patches will
be working based on it.
[bhelgaas: use pci_pcie_type() since pci_dev.pcie_type was removed]
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The upcoming VFIO support requires a way to know which
entry in the TCE map is not empty in order to do cleanup
at QEMU exit/crash. This patch adds such functionality
to POWERNV platform code.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we mark the DABRX to interrupt on all matches
(hypervisor/kernel/user and then filter in software. We can be a lot
smarter now that we can set the DABRX dynamically.
This sets the DABRX based on the flags passed by the user.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rework set_dabr to take a DABRX value as well.
Both the pseries and PS3 hypervisors do some checks on the DABRX
values that are passed in the hcall. This patch stops bogus values
from being passed to hypervisor. Also, in the case where we are
clearing the breakpoint, where DABR and DABRX are zero, we modify the
DABRX value to make it valid so that the hcall won't fail.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch does cleanup on EEH PCI address cache based on the fact
EEH core is the only user of the component.
* Cleanup on function names so that they all have prefix
"eeh" and looks more short.
* Function printk() has been replaced with pr_debug() or
pr_warning() accordingly.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The idea comes from Benjamin Herrenschmidt. The eeh cache helps
fetching the pci device according to the given I/O address. Since
the eeh cache is serving for eeh, it's reasonable for eeh cache
to trace eeh device except pci device.
The patch make eeh cache to trace eeh device. Also, the major
eeh entry function eeh_dn_check_failure has been renamed to
eeh_dev_check_failure since it will take eeh device as input
parameter.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While EEH module is installed, PCI devices is checked one by one
to see if it supports eeh. On different platforms, the PCI devices
are referred through different ways when the EEH module is loaded.
For example, on pSeries platform, that is done by OF node. However,
we would do that by real PCI devices (struct pci_dev) on PowerNV
platform in future. So we needs some mechanism to differentiate
those cases by classifying them to probe modes, either from OF
nodes or real PCI devices.
The patch implements the support to eeh probe mode. Also, the
EEH on pSeries has set it into EEH_PROBE_MODE_DEVTREE. That means
the probe will be done based on OF nodes on pSeries platform.
In addition, On pSeries platform, it's done by OF nodes. The patch
moves the the probe function from EEH core to platform dependent
backend and some cleanup applied.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch removes the eeh related statistics for eeh device since
they have been maintained by the corresponding eeh PE. Also, the
flags used to trace the state of eeh device and PE have been reworked
for a little bit.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch reworks the current implementation so that the eeh errors
will be handled basing on PE instead of eeh device.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Once eeh error is found, eeh event will be created and put it into
the global linked list. At the mean while, kernel thread will be
started to process it. The handler for the kernel thread originally
was eeh device sensitive.
The patch reworks the handler of the kernel thread so that it's PE
sensitive.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch implements reset based on PE instead of eeh device. Also,
The functions used to retrieve the reset type, either hot or fundamental
reset, have been reworked for a little bit. More specificly, it's
implemented based the the eeh device traverse function.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch refactors the original implementation in order to enable
I/O and retrieve EEH log based on PE.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch introduces the function to traverse the devices of the
specified PE and its child PEs. Also, the restore on device bars
is implemented based on the traverse function.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Originally, all the EEH operations were implemented based on OF node.
Actually, it explicitly breaks the rules that the operation target
is PE instead of device. Therefore, the patch makes all the operations
based on PE instead of device.
Unfortunately, the backend for config space has to be kept as original
because it doesn't depend on PE.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There're 2 conditions to trigger EEH error detection: invalid value
returned from reading I/O or config space. On each case, the function
eeh_dn_check_failure will be called to initialize EEH event and put
it into the poll for further processing.
The patch changes the function for a little bit so that the EEH error
will be traced based on PE instead of EEH device any more. Also, the
function eeh_find_device_pe() has been removed since the eeh device
is tracing the PE by struct eeh_dev::pe.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since we've introduced dedicated struct to trace individual PEs,
it's reasonable to trace its state through the dedicated struct
instead of using "eeh_dev" any more.
The patches implements the state tracing based on PE. It's notable
that the PE state will be applied to the specified PE as well as
its child PEs. That complies with the rule that problematic parent
PE will prevent those child PEs from working properly.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The original implementation builds EEH event based on EEH device.
We already had dedicated struct to depict PE. It's reasonable to
build EEH event based on PE.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During PCI hotplug and EEH recovery, the PE hierarchy tree might be
changed due to the PCI topology changes. At later point when the
PCI device is added, the PE will be created dynamically again.
The patch introduces new function to remove EEH devices from the
associated PE. That also can cause that the parent PE is removed
from the PE tree if the parent PE doesn't include valid EEH devices
and child PEs.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch creates PEs and associated the newly created PEs with
it parent/silbing as well as EEH devices. It would become more
straight to trace EEH errors and recover them accordingly.
Once the EEH functionality on one PCI IOA has been enabled, we
tries to create PE against it. If there's existing PE, to which
the current PCI IOA should be attached, the existing PE will be
converted from "device" type to "bus" type accordingly.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch implements searching PE based on the following
requirements:
* Search PE according to PE address, which is traditional
PE address that is composed of PCI bus/device/function
number, or unified PE address assigned by firmware or
platform.
* Search parent PE according to the given EEH device. It's
useful when creating new PE and put it into right position.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For one particular PE, it's only meaningful in the ancestor PHB
domain. Therefore, each PHB should have its own PE hierarchy tree
to trace those PEs created against the PHB.
The patch creates PEs for the PHBs and put those PEs into the
global link list traced by "eeh_phb_pe". The link list of PEs
would be first level of overall PE hierarchy tree across the
system.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch introduces global mutex for EEH so that the core data
structures can be protected by that. Also, 2 inline functions
are exported for that: eeh_lock() and eeh_unlock().
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch adds more logs to EEH initialization functions for
debugging purpose. Also, the machine type (pSeries) is checked
in the platform initialization to assure it's the correct platform
to invoke it.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The EEH initialization functions have been postponed until slab/slub
are ready. So we use slab/slub to allocate the memory chunks for newly
creatd EEH devices. That would save lots of memory.
The patch also does cleanup to replace "kmalloc" with "kzalloc" so
that we needn't clear the allocated memory chunk explicitly.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, we have 3 phases for EEH initialization on pSeries platform.
All of them are done through builtin functions: platform initialization,
EEH device creation, and EEH subsystem enablement. All of them are done
no later than ppc_md.setup_arch. That means that the slab/slub isn't ready
yet, so we have to allocate memory chunks on basis of PAGE_SIZE for those
dynamically created EEH devices. That's pretty expensive.
In order to utilize slab/slub for memory allocation, we have to move the EEH
initialization functions around, but all of them should be called after slab
is ready.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt
Gavin Shan
Aneesh Kumar K.V
Bjorn Helgaas
Jia Hongtao
Zhao Chenhui
Timur Tabi
Alexey Kardashevskiy
Michael Neuling