Although the ES8328 does support different rates for capture and
playback, only very limited combinations are supported (8kHz and 48kHz
or 8.0182kHz and 44.1kHz) with most rates required to be symmetric.
Instead of adding a lot of complexity for little gain, let's enforce
symmetric rates.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The values are the same for the DAC and ADC so remove the specific
values and use values with shifts.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a refactor in preparation for supporting more sample sizes which
has no functional change.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is always used along with ES8328_CONTROL1_ENREF so there is no
change in the generated code as a result of this fix.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ADCCONTROL4 and DACCONTROL1 registers are similar but not identical,
with the DACCONTROL1 having each field starting one bit higher than
ADCCONTROL4.
Instead of introducing a magic shift, add new constants for the values
in ADCCONTROL4 and use a second variable to setup the ADC.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This ensures that the clock is setup after its frequency has been set;
the existing code in set_dai_fmt may be called before the clock rate has
been set resulting in an incorrect configuration.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds "DLGS7219" ACPI id for the codec.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Tested-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We only polling jd status when rt5645->pdata.jd_invert is true.
However, it should be done at all time since there will be no
interrupt for jd if we press a headset button and remove the
headset at the same time.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If someone powers down the DSP core (through routing changes
say) whilst a compressed record is in progress we can end up
using a freed pointer to the buffer object. When a compressed
audio stream is triggered we attach it to a buffer on a physical
DSP. This patch adds a detach of the buffer from the stream when
the stream is freed or when the DSP is powered down which avoids
the situation where we use a buffer when it is no longer valid.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move wm_adsp_compr_attach and wm_adsp_compr_attached functions so they
will stay logically grouped with similar functions after some additional
changes.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We intended || here instead of &&. The original code potentially leads
to a NULL dereference.
Fixes: 2889099eb8 ('ASoC: hdac_hdmi: Register chmap controls and ops')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewd-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Sachin Mokashi <sachinx.mokashi@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the arbitrary length TLV based binary
controls. This allows users to properly access controls that are
more than 512 bytes in length.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With this patch, chmap controls are created and user space can
set the channel map.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support multichannel hdac hdmi driver registers with HDA
channel map framework. Channel count and channel slot verbs are
programmed by using the chmap helpers/ops. The channel
allocation is then programmed in the audio infoframe as per CEA
spec.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch parses ELD speaker allocation data block to find
sink's chmap capability.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Texas Instruments TAS5720L/M device is a high-efficiency mono
Class-D audio power amplifier optimized for high transient power
capability to use the dynamic power headroom of small loudspeakers.
Its digital time division multiplexed (TDM) interface enables up to
16 devices to share the same bus.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a function to delete and free the contents of the alg_regions list.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Ensure that the wm_adsp driver cleans up when the codec driver
is removed.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch adds a wm_adsp2_remove() function to ensure that memory
is freed when the driver is unloaded or shut down.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bits in the ARIZONA_CLOCK_CONTROL register only respond to writes of
a '1', a write of '0' is ignored. So there's no need to use update_bits.
We can do a simple write to set bits.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Bard Liao <bardliao@realtek.com>
Cc: Oder Chiou <oder_chiou@realtek.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT298_CBJ_CTRL1(0x4f) bit 10 is needed for headset capture. It
will be turned off when "VREF" widget is on and be turned on when
bias level is ON. It is odd. And if "VREF" is turned on in bias
level is ON, RT298_CBJ_CTRL1(0x4f) bit 10 will be turned off.
This patch move the bit control from rt298_set_bias_level and
rt298_vref_event to rt298_jack_detect. So it will be turned on
once a jack is plugged in.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt298 need to reset AD filter and the ADC settings will take effort.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The expected MCLK frequency ranges and the associated dividers
are updated to improve PLL locking in a corner scenario, with low
MCLK frequency near an input divider change boundary.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA doesn't know about all the different compressed audio formats,
so there is no interface to let userspace enumerate the formats that
are supported by the connected sink. Exporting the raw ELD bytes to
userspace allows an application to select the appropriate audio format
depending on the current capabilities of the connected HDMI sink device.
Usually userspace then just pretends to ALSA that the data is in one of
the raw 16-bit PCM audio formats and relies on the IEC controls to tell
the sink how to interpret the data.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When setting up an FLL in pseudo-fractional mode it is preferred
to use a lower FRATIO if possible to give a higher reference clock
frequency. This patch swaps the two loops in arizona_calc_fratio()
so that lower FRATIOs are tried first. The decrementing loop is also
changed to start from init_ratio because the original settings might
already give a fractional value for N.K
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The input mixers support routing the IN1_R pin to the Left PGA and the
IN2_L pin to the Right PGA. This patch allows for those routings.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The input pins of the aic3204 have resistors inline with them. The
current code assumes that you want a 10k resistor inline with your
inputs and implements it as a simple switch. This patch creates an enum
for each pin and allows you to switch between not connected, 10k, 20k
and 40k ohm values. This more closely models the acutal aic3204 part.
These pin settings are documented in TI's SLAA557 pages 135 and 136
(http://www.ti.com/lit/ml/slaa557/slaa557.pdf).
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TLV320AIC32x4 series supports 96ksps rates in hardware. This patch
adds the necessary PLL divider values and clock settings to the table to
make 96ksps work.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Lenovo 100S netbook has a codec controller for which there is a
driver, but doesn't know how to access the device. This adds the
necessary ACPI table for the driver to find the device.
Device (TTLV)
{
Name (_ADR, Zero) // _ADR: Address
Name (_HID, "10TI3100") // _HID: Hardware ID
Name (_CID, "10TI3100") // _CID: Compatible ID
Name (_DDN, "TI TLV320AIC3100 Codec Controller ") // _DDN: DOS Device Name
Name (_UID, One) // _UID: Unique ID
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Jan Schmidt <jan@centricular.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PLL function was updated to disallow 32KHz in
commit 501f72e9c5 ("ASoC: da7219: Remove support for 32KHz PLL mode"),
but set_dai_sysclk() was missed and still permits it. This patch resolves
that discrepancy.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The expected MCLK frequency ranges and the associated dividers
are updated to improve PLL locking in a corner scenario, with low
MCLK frequency near an input divider change boundary.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for running the tlv32x4 control channel over SPI rather than I2C.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
To prepare for abstracting adding SPI support, the I2C pieces needs to
be in its own moudle. This patch moves common probe code into aic32x4_probe
and common removal code into aic32x4_remove. It also creates a static
regmap config structure to be copied in the I2C specific driver.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec's probe function is named aic32x4_probe. This is going to
conflict with later work to implement SPI support and separate out I2S
into its own file. In line with other drivers in the tree, this function
is renamed to aic32x4_codec_probe instead.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hdmi-codec is a platform device driver to be registered from
drivers of external HDMI encoders with I2S and/or spdif interface. The
driver in turn registers an ASoC codec for the HDMI encoder's audio
functionality.
The structures and definitions in the API header are mostly redundant
copies of similar structures in ASoC headers. This is on purpose to
avoid direct dependencies to ASoC structures in video side driver.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We request one of the DSP IRQs during CODEC probe, as such we should
free it during CODEC remove, this patch does so.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The thermal warning IRQs for the speaker are requested in CODEC probe
but never freed. This patch frees them in CODEC remove.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The CS47L24 and WM1831 codecs only use the OUT4L widget so we can
skip creation of the OUT4R widget.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If we encounter an error on the DSP side whilst user-space is
waiting on the poll we should call snd_compr_fragment_elapsed,
although data is not actually available we want to wake
user-space such that the error can be propagated out
quickly. Additionally some versions of the DSP firmware are
not super consistent about actually generating an IRQ if they
encounter an error, as such we will check the DSP error status
every time we run out of available data as well, to ensure we
catch it.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Factor out the reading of the DSP error flag into its own function to
support further improvements to the code.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the system enters S3 during a playback, codec power needs to
be turned OFF during suspend and restored during resume. With
this patch the AFG node is set to D3 and codec power is turned
OFF during controller suspend call.
During resume, the codec power is left in ON state if the
playback was in progress while suspending.
Also setting power state for AFG node is optimized. With this the
loop with timeout is removed and codec_read is used instead.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use dev_pm ops feature instead of soc pm as core assumes system
is capable of direct complete. Register with complete callback
instead of resume to synchronize with Jack notification from
display driver. This ensures correct Jack notification to user
space.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The list of TAS571x registers was incomplete.
Added the missing register definitions up to the register 0x25.
Added volatile and read-only register tables into tas5711_regmap_config
and tas5717_regmap_config.
The chip has 256 registers in total. But from address 0x29 on
(0x26 to 0x28 are reserved) the register width varies between
20, 12 and 8 bytes, which the register map cannot represent.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The chip selection was relying only on DT. It was not possible to use the
driver without DT.
This adds the chip type detection from the I2C name, which
allows to use the driver from the platform driver without DT.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Reviewed-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that this is directly user selectable it needs to care about its
dependencies.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver did not have a mute function. The amplifier was brought out of
shutdown mode (hard-mute) once for ever in probe(), which was causing
clicks and pops when altering the I2C register configuration later.
This adds the digital_mute() function. The amplifier unmute in probe()
was removed.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
cs47l24 supports the audio trace firmware, this streams of audio to be
captured from the CODEC over a compressed audio channel for
analysis/debugging of audio processing firmwares.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All other debug messages talk about data on the compressed stream in
bytes except avail which is shown in words. To avoid confusion show
avail in bytes as well.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Firstly, we should be locking the pwr_lock when we initialise the
compressed buffer. Secondly, fixup a couple of places when we should be
pulling pointers only under the pwr_lock as they may be affected by
operations that take that lock.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When trying to use simple card with wm8962 the following probe
error happens:
wm8962 0-001a: simple-card: set_sysclk error
asoc-simple-card sound: ASoC: failed to init 202c000.ssi-wm8962: -22
asoc-simple-card sound: ASoC: failed to instantiate card -22
asoc-simple-card: probe of sound failed with error -22
In simple-card.c the snd_soc_dai_set_sysclk() function is called with
clk_id as 0, which is an invalid clock for wm8962.
Adjust the clocks source definitions in wm8962.h so that the
simple card driver can work successfully.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable dspclk holds the rate of the DSPCLK, but the variable
sysclk holds an identifier for the clock. Currently if read a
non-sensical value from the DSPCLK_DIV register we assign sysclk to
dspclk, clearly this was intended to be sysclk_rate.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The error message fits well into a single line.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When regulator_bulk_enable() fails inside wm8962_runtime_resume(),
we should disable the previously enabled clock.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Provide a menu selection text so that users can enable, disable or
mark it as module in menuconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jack plug status is rechecked at resume to handle plug/unplug
in S3 when the chip has no power.
Suspend/resume callbacks are moved from the i2c dev_pm_ops to
snd_soc_codec_driver. soc_resume_deferred is a delayed work
which may trigger nau8825_set_bias_level. The bias change races
against dev_pm_ops, causing jack detection issues.
soc_resume_deferred ensures bias change and snd_soc_codec_driver
suspend/resume are sequenced correctly.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
After a heavy storm by syzkaller in 4.5 cycle, we have relatively few
changes in the core at this time while a lot of changes are found in
the driver side, unsurprisingly. Below are some highlights:
ALSA core:
- A few more hardening in ALSA timer codes
- An extension of sequencer API for advertising the card / pid
- Small fixes in compress-offload and jack layers
HD-audio:
- Dynamic PCM assignment in HDMI/DP codec; preparation for upcoming
DP-MST support
- Lots of code refactoring for sharing with ASoC SKL driver
- Regression fixes for Intel HDMI/DP
- Fixups for CX20724 codec, Lenovo AiO
USB-audio:
- Add quirk_alias option to make quirk debugging easier
- Fixes for possible Oops by malformed firmware
Firewire:
- Add support for FW-1804 in tascam driver
- Improvements / changes in card registration, multi stream handling,
etc for DICE
- Lots of code refactoring
ASoC:
- Enhancements of still ongoing topology API
- Lots of commits for Intel Skylake support including HDMI support
- A few Intel Atom driver updates for recent devices
- Lots of improvements to the Renesas drivers
- Capture support for Qualcomm drivers
- Support for TI DaVinci DRA7xxx devices
- New machine drivers for Freescale systems with Cirrus CODECs,
Mediatek systems with RT5650 CODECs
- New CPU drivers for Allwinner S/PDIF controllers
- New CODEC drivers for Maxim MAX9867 and MAX98926 and Realtek RT5514
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Cc+v
-----END PGP SIGNATURE-----
Merge tag 'sound-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"After a heavy storm by syzkaller in 4.5 cycle, we have relatively few
changes in the core at this time while a lot of changes are found in
the driver side, unsurprisingly. Below are some highlights:
ALSA core:
- A few more hardening in ALSA timer codes
- An extension of sequencer API for advertising the card / pid
- Small fixes in compress-offload and jack layers
HD-audio:
- Dynamic PCM assignment in HDMI/DP codec; preparation for upcoming
DP-MST support
- Lots of code refactoring for sharing with ASoC SKL driver
- Regression fixes for Intel HDMI/DP
- Fixups for CX20724 codec, Lenovo AiO
USB-audio:
- Add quirk_alias option to make quirk debugging easier
- Fixes for possible Oops by malformed firmware
Firewire:
- Add support for FW-1804 in tascam driver
- Improvements / changes in card registration, multi stream handling,
etc for DICE
- Lots of code refactoring
ASoC:
- Enhancements of still ongoing topology API
- Lots of commits for Intel Skylake support including HDMI support
- A few Intel Atom driver updates for recent devices
- Lots of improvements to the Renesas drivers
- Capture support for Qualcomm drivers
- Support for TI DaVinci DRA7xxx devices
- New machine drivers for Freescale systems with Cirrus CODECs,
Mediatek systems with RT5650 CODECs
- New CPU drivers for Allwinner S/PDIF controllers
- New CODEC drivers for Maxim MAX9867 and MAX98926 and Realtek RT5514"
* tag 'sound-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (291 commits)
ALSA: hda - Fix mutex deadlock at HDMI/DP hotplug
ALSA: ctl: change return value in compatibility layer so that it's the same value in core implementation
ALSA: mixart: silence an uninitialized variable warning
ALSA: usb-audio: Add sanity checks for endpoint accesses
ALSA: usb-audio: Minor code cleanup in create_fixed_stream_quirk()
ALSA: usb-audio: Fix NULL dereference in create_fixed_stream_quirk()
ALSA: hda - Limit i915 HDMI binding only for HSW and later
ALSA: hda - Fix unconditional GPIO toggle via automute
ALSA: mixart: silence unitialized variable warnings
ALSA: hda - Fixes double fault in nvhdmi_chmap_cea_alloc_validate_get_type
ALSA: intel8x0: Add clock quirk entry for AD1981B on IBM ThinkPad X41.
ALSA: hda - Add new GPU codec ID 0x10de0082 to snd-hda
ASoC: rsnd: add simplified module explanation
ASoC: hdac_hdmi: Add broxton device ID
ASoC: Intel: Bxtn: Add Broxton PCI ID
ASoC: Intel: Skylake: Move Skylake dsp ops & loader ops
ASoC: Intel: add dmabuffer to common sst_dsp
ASoC: Intel: Skylake: Unstatify skl_dsp_enable_core
ASoC: Intel: Skylake: Fix whitepsace issues
ASoC: Intel: Skylake: Move module id defines
...
this patch corrects the interface adc/dac control register definition
according to datasheet.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The rt5616 codec registers itself as an i2c driver, but can
be enabled even when i2c is turned off, which leads to a build
error:
codecs/rt5616.c:1419:1: error: data definition has no type or storage class [-Werror]
module_i2c_driver(rt5616_i2c_driver);
This adds an explicit Kconfig dependency, like the other codec
drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 288bc356a8 ("ASoC: rt5616: allow to build with CONFIG_SND_SOC_RT5616")
Signed-off-by: Mark Brown <broonie@kernel.org>
This has been an extremely quiet release for the regulator API, aside
from bugfixes and small enhancements the only thing that really stands
out are the new drivers for Action Semiconductors ACT8945A, HiSilicon
HI665x, and the Maxim MAX20024 and MAX77620.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW58EWAAoJECTWi3JdVIfQMGMH/1v4ojMy0X/yPlFk/523u7uq
6ZJQ4zSTPyv0ccR+hsDjZ81BmM/vATrnQOllvTSwfnGMcs5amE3/9EhzdF5EciCB
8gUff/GfugXNqpVgpfYYfPhbQVTGllOFnZPmXsLx2dGlu094i69f4fZtoJCFlkmo
5c0L5Fnkt4w5XtFAA6ILuRtpwZ4jfJZ3VFKrtYwkgLcKw9GgSEqhVKvTPfkNqtjg
hzEl2P2K/Ug2uTqeZusKH30Sa1J7MW4B+C9dUVyTRB29+uA60y0foGTQjW9uCzEi
l1sqY9VDSKp9WwnshVrgVFViAhkrA7fWl4qaC/EDe7avvbh5SBpR/+gjZbmdRJU=
=jEl0
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This has been an extremely quiet release for the regulator API, aside
from bugfixes and small enhancements the only thing that really stands
out are the new drivers for Action Semiconductors ACT8945A, HiSilicon
HI665x, and the Maxim MAX20024 and MAX77620"
* tag 'regulator-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (46 commits)
regulator: pwm: Add support to have multiple instance of pwm regulator
regulator: pwm: Fix calculation of voltage-to-duty cycle
regulator: of: Use of_property_read_u32() for reading min/max
regulator: pv88060: fix incorrect clear of event register
regulator: pv88090: fix incorrect clear of event register
regulator: max77620: Add support to configure active-discharge
regulator: core: Add support for active-discharge configuration
regulator: helper: Add helper to configure active-discharge using regmap
regulator: core: Add support for active-discharge configuration
regulator: DT: Add DT property for active-discharge configuration
regulator: act8865: Specify fixed voltage of 3.3V for ACT8600's REG9
regulator: act8865: Rename platform_data field to init_data
regulator: act8865: Remove "static" from local variable
ASoC: cs4271: add regulator consumer support
regulator: max77620: Remove duplicate module alias
regulator: max77620: Eliminate duplicate code
regulator: max77620: Remove unused fields
regulator: core: fix crash in error path of regulator_register
regulator: core: Request GPIO before creating sysfs entries
regulator: gpio: don't print error on EPROBE_DEFER
...
gcc warns about the possibilty of accessing a property read from
devicetree in cs35l32_i2c_probe() when it has not been initialized
because CONFIG_OF is disabled:
sound/soc/codecs/cs35l32.c: In function 'cs35l32_i2c_probe':
sound/soc/codecs/cs35l32.c:278:2: warning: 'val' may be used uninitialized in this function [-Wmaybe-uninitialized]
The code is actually correct because it checks the dev->of_node
variable first and we know this is NULL here when CONFIG_OF
is disabled, but Russell King noticed that it's broken when
we probe the device using DT, and the properties are absent.
The code already has some checking for incorrect values, and
I keep that checking unchanged here, but add an additional
check for an error returned by the property accessor functions
that now gets handled the same way as incorrect data in the
properties.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton HDMI codec is similar to Skylake so add the device ID
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reduce pop noise in power up and down sequence when playback.
The DAPM widgets graph is reconstructed to ensure the
register write sequence at playback matches exactly to the
v5 clickless sequence provided by Nuvoton.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: 44029e9e1290 ("ASoC: wm_adsp: wm_coeff_{read|write}_control should use passed length")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Audio infoframe used incorrect buffer, so fix it.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We are getting build warning about:
sound/soc/codecs/rt5640.c:1892:11: warning: unused variable 'dai_sel'
The use of the variable was removed but the variable itself was not
removed.
Fixes: c467fc0e01 ("ASoC: rt5640: Set PLL src according to source")
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAC1/2 power is for both DACs and related mixer/mux. Add SUPPLY
type widgets to support it.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5640_set_dai_pll set pll source according to given source and
dai id. However, the pll source should be set according to given
source only.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
John Keeping
Mark Brown
Adam Thomson
Bard Liao
Charles Keepax
Dan Carpenter
Subhransu S. Prusty
anish kumar
Andreas Dannenberg
Richard Fitzgerald
Linus Walleij
Javier Martinez Canillas
Kuninori Morimoto
Philipp Zabel
Jeremy McDermond
Stephen Boyd
Bastien Nocera
Jyri Sarha
Petr Kulhavy
Axel Lin
Fabio Estevam
Ben Zhang
John Lin
Linus Torvalds
Sugar Zhang
Arnd Bergmann
Jeeja KP
John Hsu
Sudip Mukherjee