This is the third and smallest of the SoC specific updates.
Changes include:
* SMP support for the Xilinx zynq platform
* Smaller imx changes
* LPAE support for mvebu
* Moving the orion5x, kirkwood, dove and mvebu platforms
to a common "mbus" driver for their internal devices.
It would be good to get feedback on the location of the "mbus"
driver. Since this is used on multiple platforms may potentially
get shared with other architectures (powerpc and arm64), it
was moved to drivers/bus/. We expect other similar drivers to
get moved to the same place in order to avoid creating more
top-level directories under drivers/ or cluttering up the
messy drivers/misc/ even more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=rQsu
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates (part 3) from Arnd Bergmann:
"This is the third and smallest of the SoC specific updates. Changes
include:
- SMP support for the Xilinx zynq platform
- Smaller imx changes
- LPAE support for mvebu
- Moving the orion5x, kirkwood, dove and mvebu platforms to a common
"mbus" driver for their internal devices.
It would be good to get feedback on the location of the "mbus" driver.
Since this is used on multiple platforms may potentially get shared
with other architectures (powerpc and arm64), it was moved to
drivers/bus/. We expect other similar drivers to get moved to the
same place in order to avoid creating more top-level directories under
drivers/ or cluttering up the messy drivers/misc/ even more."
* tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: imx: reset_controller may be disabled
ARM: mvebu: Align the internal registers virtual base to support LPAE
ARM: mvebu: Limit the DMA zone when LPAE is selected
arm: plat-orion: remove addr-map code
arm: mach-mv78xx0: convert to use the mvebu-mbus driver
arm: mach-orion5x: convert to use mvebu-mbus driver
arm: mach-dove: convert to use mvebu-mbus driver
arm: mach-kirkwood: convert to use mvebu-mbus driver
arm: mach-mvebu: convert to use mvebu-mbus driver
ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock
ARM i.MX53: tve_di clock is not part of the CCM, but of TVE
ARM i.MX53: make tve_ext_sel propagate rate change to PLL
ARM i.MX53: Remove unused tve_gate clkdev entry
ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree
ARM: i.MX5: Add PATA and SRTC clocks
ARM: imx: do not bring up unavailable cores
ARM: imx: add initial imx6dl support
ARM: imx1: mm: add call to mxc_device_init
ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS
ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS
...
This commit migrates the mach-kirkwood platforms to use the mvebu-mbus
driver and therefore removes the Kirkwood-specific addr-map code.
The kirkwood_init_early() function is now responsible for initializing
the mvebu-mbus driver by calling mvebu_mbus_init().
The address decoding windows are now registered in the
kirkwood_setup_wins() function. It is worth noting that the four PCIe
address decoding windows will ultimately no longer have to be
registered here: it will be done automatically by the PCIe driver once
Kirkwood has been migrated to use the upcoming mvebu PCIe driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds DT board setup for the LaCie NAS CloudBox. The CloudBox
is a low cost NAS based on the Network Space v2.
Chipset list:
- CPU MARVELL 88F6702 1Ghz
- SDRAM memory: 256MB DDR2-800 (2x128MB x8) 400Mhz
- 1 Ethernet Gigabit port (PHY MARVELL 88E1318)
- SPI flash, NOR 512KB
- 1 push button
- 2 LEDs (red and blue)
There is no EEPROM and no USB ports embedded.
Note that this board must not be confused with the Network Space Mini v2
which is embedded in a previous LaCie product also named CloudBox.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch sorts board entries in files Kconfig, Makefile and
kirkwood_defconfig by ASCII-code order.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add support for NETGEAR ReadyNAS Duo v2 (Hardware specs available
here: http://natisbad.org/NAS/). Almost everything is supported via
provided .dts. A board-readynas.c file is nonetheless required for
device not only converted to DT (Gbit controller).
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Tested-By: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add a device tree entry for the Guruplug Server Plus board. This port
was based both on the work done on the dreamplug and the dockstar.
It builds, boots and works on my Guruplug Server Plus.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Move the Kirkwood cpuidle driver out of arch/arm/mach-kirkwood and
into drivers/cpuidle. Convert the driver into a platform driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add support for Plat'Home OpenBlocks A6 using the device tree
where possible.
This commit supports SATA, USB, ether and serial console.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Hello, Andrew
> > +#define NSA310_GPIO_LED_ESATA_GREEN 12
> > <..>
> > +#define NSA310_GPIO_POWER_OFF 48
>
> It looks like most of these are not used. Please remove them.
True. Fixed.
> > +static struct mtd_partition nsa310_mtd_parts[] = {
> > + {
> > + .name = "uboot",
> > + .offset = 0,
> > + .size = 0x100000,
> > + .mask_flags = MTD_WRITEABLE,
> > + }, {
> > <..>
> You should be able to put all that into DT. Take a look at
Correct. I did the conversion and tested that the partitions
can be read with dd and produce exactly the same data before and
after conversion. So, the partition offsets at least should be fine.
> > +static struct i2c_board_info __initdata nsa310_i2c_info[] = {
> > + { I2C_BOARD_INFO("adt7476", 0x2e) },
> > +};
>
> You can also do this in DT as well. kirkwood-ts219.dtsi has
>
> i2c@11000 {
> status = "okay";
> clock-frequency = <400000>;
Ok, I did convert the i2c definition to use the devicetree.
The adt7476 device itself is not at reach of device tree,
AFAIK and requires more work at there?
Thanks for your valuable comments. Following is a new patch that
should address the problems and mistakes you pointed and also
some of the pointed by Jason Cooper. The nand and i2c are now
defined at DT and I also removed the pointless defines and
ARM_APPENDED_DTB. It is based against the Linus' official
3.6 version.
Best regards,
Tero
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This is a new kirkwood box made by Universal Scientific Industrial, Inc.
The product description is here:
http://www.usish.com/english/products_topkick1281p2.php
It is very similar to the dreamplug and other plug devices, with the
exception that it has room for a 2.5" SATA HDD internally.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch adds DT board setup for the LaCie NAS Network Space Mini v2
(aka SafeBox). The hardware characteristics are very close to those of
the Network Space Lite v2. The main difference are:
- A GPIO fan which is only available on the NS2 Mini.
- A single USB host port is wired on the NS2 Mini. The NS2 Lite provides
an additional dual-mode USB port (host/device).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds DT board setup for the LaCie NAS Network Space Lite v2.
This board is derived from the Network Space v2 and a lot of hardware
characteristics are shared.
- CPU: Marvell 88F6192 800Mhz
- SDRAM memory: 128MB DDR2 200Mhz
- 1 SATA port: internal
- Gigabit ethernet: PHY Marvell 88E1318
- Flash memory: SPI NOR 512KB (Macronix MX25L4005A)
- i2c EEPROM: 512 bytes (24C04 type)
- 2 USB2 ports: host and host/device
- 1 push button
- 1 SATA LED (bi-color, blue and red)
Note that the SATA LED is not compatible with the driver leds-ns2. The
LED behaviour ("on", "off" or "SATA activity blink") is controlled via
a single MPP (21).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds DT board setup for LaCie Network Space v2 and parents,
based on the Marvell Kirkwood 6281 SoC. This includes Network Space v2
(Max) and Internet Space v2.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This is a first attempt to support the km_kirkwood reference design with
a device tree. This km_kirkwood design is present in many Keymile
products. It is based on the Marvell Bobcat SOC which integrates a
Kirkwood CPU next to a big L2 Ethernet Switch. The Kirkwood in the SOC
is very similar to the "normal" one, but there are a few differences.
This initial support is minimal: the kernel can boot with network
(ge0), serial port and NAND functional.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This add a DT compatible board specific setup for the Seagate
FreeAgent Dockstar.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add support for Buffalo Linkstation LS-XHL and LS-CHLv2 using the device
tree where possible.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
This patch supplies the necessary DTS and supporting files to boot up
a Seagate GoFlex Net with 3.5.0-rc3.
Signed-off-by: Joshua Coombs <josh.coombs@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The two different variants of QNAP TS devices, varying by SoC, put the
GPIO keys on different GPIO lines. Hence we need two different DT
board descriptions, which share the same board-ts219.c file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Add support for the IB-NAS6210 and IB-NAS 6220. Describe as much as
currently possible in the devicetree files, including the NAND partitions.
Use the partition scheme of the original firmware by default.
Create a board-ib62x0.c for everything else.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add support for Iomega Iconnect system.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-By: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add support for the DNS-320 and DNS-325. Describe as much as currently possible
in the devicetree files, create a board-dnskw.c for everything else.
Changes since last submission (V3) [Addressing comments by]:-
* One MACH_DLINK_KIRKWOOD_DT for all dtb files [Grant Likely, Jason Cooper]
* Drop brain-dead select "select CONFIG_MTD_OF_PARTS" [Grant Likely]
* Don't add NAND support then throw it away immediately after [Grant Likely]
* Describe purpose of MPP 41, 42 & 49
Changes since last submission (V2):-
* Use IEEE-compliant "okay", rather than "ok" [Scott Wood]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Move all dreamplug-specific code out of board-dt.c and into
board-dreamplug.c. This way new boards that are added during the
conversion to fdt don't clutter up board-dt.c.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Initially, copied guruplug-setup.c and did s/guruplug/dreamplug/g.
Then, switched to SPI based NOR flash.
After talking to Arnd Bergman, chose an incremental approach to adding
devicetree support. First, we use the dtb to tell us we are on the
dreamplug, then we gradually port over drivers.
Driver porting will start with the uart (see next patch), and progress
from there. Possibly, spi/flash/partitions will be next.
When done, board-dt.c will no longer be dreamplug specific, and dt's can
be made for the other kirkwood boards.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds support for the Seagate FreeAgent DockStar,
a Marvell SheevaPlug variant.
Signed-off-by: Eric Cooper <ecc@cmu.edu>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Add support for the HP t5325 Thin Client. This thin client is based
on a Marvell Kirkwood chip at 1.2 GHz and features 512 MB RAM, 512 MB
SATA-attached flash and an XGI Volari Z11 GPU.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
GuruPlug Standard: 1 Gb Ethernet, 2 USB 2.0
GuruPlug Plus: 2 Gb Ethernet, 2 USB 2.0, 1 eSATA, 1 uSD slot
References:
http://www.globalscaletechnologies.com/t-guruplugdetails.aspxhttp://plugcomputer.org
This patch is for GuruPlug Plus, but it supports Standard version
as well.
Signed-off-by: Siddarth Gore <gores@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Allow basic eSATA SheevaPlug board configuration and build.
Signed-off-by: John Holland <john.holland@cellent-fs.de>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
--
The Internet and Network Space v2 boards are very close. The only
difference is that there is no USB type B plug wired on the Internet
Space v2.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Inspired by the mach-ep93xx flattening work, there is really not
much difference between the OpenRD base and client board support
so they should be merged together.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Acked-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Remove the code duplication found in the setup files of TS-219 and
TS-41x.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Add support for the QNAP TS-410, TS-410U, TS-419P and TS-419U
Turbo NAS.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The patch adds support for Kirkwood cpu idle.
Two idle states are defined:
1. Wait-for-interrupt (replacing default kirkwood wfi)
2. Wait-for-interrupt and DDR self refresh
Signed-off-by: Rabeeh Khoury <rabeeh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Add support for the QNAP TS-119 and TS-219 Turbo NAS devices.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This allows for board support code to set up their MPP config if the
bootloader didn't do it all or did it wrong. This also allows to
register usable GPIOs.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The Marvell Kirkwood (88F6000) is a family of ARM SoCs based on a
Shiva CPU core, and features a DDR2 controller, a x1 PCIe interface,
a USB 2.0 interface, a SPI controller, a crypto accelerator, a TS
interface, and IDMA/XOR engines, and depending on the model, also
features one or two Gigabit Ethernet interfaces, two SATA II
interfaces, one or two TWSI interfaces, one or two UARTs, a
TDM/SLIC interface, a NAND controller, an I2S/SPDIF interface, and
an SDIO interface.
This patch adds supports for the Marvell DB-88F6281-BP Development
Board and the RD-88F6192-NAS and the RD-88F6281 Reference Designs,
enabling support for the PCIe interface, the USB interface, the
ethernet interfaces, the SATA interfaces, the TWSI interfaces, the
UARTs, and the NAND controller.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Linus Torvalds
Thomas Petazzoni
Simon Guinot
Arnaud Ebalard
Willy Tarreau
Andrew Lunn
Nobuhiro Iwamatsu
Stefan Peter
Tero Jaasko
Jason Cooper
Valentin Longchamp
Sebastian Hesselbarth
Alan M Butler
Michael Walle
Josh Coombs
Simon Baatz
Arnaud Patard (Rtp)
Jamie Lentin
Simon Guinot
Eric Cooper
Martin Michlmayr
Siddarth Gore
Russell King
John Holland
Alexander Clouter
Dhaval Vasa
Lennert Buytenhek
Rabeeh Khoury
Shadi Ammouri
Nicolas Pitre
Saeed Bishara