Add support for transparent DMA transfer of JPEG data with MIPI-CSI2
USER1 format. In JPEG mode the color effect, scaling and cropping
is not supported as well as image rotation and flipping thus these
controls are marked as inactive if V4L2_PIX_FMT_JPEG pixel format
was selected.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a subdev to expose the host's scaling and composition functions.
The camera frame composition onto an output buffer may be configured
through set/get_crop at FIMC.{n} source pad.
Additionally allow crop, composition and controls to be modified
during streaming. Make sure the default format is set when opening
the video capture node.
Rename struct fimc_vid_cap::fmt to more relevant 'mf' to avoid
confusion.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the camera capture driver use fimc_pipeline_* calls provided by
the media device driver part, in place where v4l2_subdev_call() were
used. This way the capture driver don't need to differentiate between
various H/W pipeline setups, i.e. if the MIPI-CSI receiver subdev is
used or not.
Remove the sync_capture_fmt() function instead of which
fimc_pipeline_try_format() is introduced in the following patch adding
the FIMC capture subdev.
The TRY_FMT ioctl function is completed by a subsequent patch adding
the capture subdev, so the try_fmt routines can be reused in the subdev
and the video node ioctl handlers.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace fimc_find_format() and find_mbus_format() with single function
that can return a pointer to the private format description based
on fourcc, media bus code or index in the table.
Create separate VIDIOC_ENUM_FMT ioctl handlers for video capture
and mem-to-mem video node. This is needed because some formats are
valid only for the video capture and some only for the mem-to-mem
video node.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the camera capture H/W initialization sequence to a separate
function. This is needed for reuse in the following runtime PM code.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the link_setup handler for the camera capture video node.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the v4l controls code to use the new control framework.
fimc_ctrls_activate/deactivate functions are introduced for the
transparent DMA transfer mode (JPEG), where the rotation and flipping
controls are not supported.
The capture video node does not inherit sensors' controls when the
subdevs are configured by the user space (user_subdev_api == true).
However by default after the driver's initialization
the 'user-subdev_api' flag is false and any sensor controls will
also be available at the video node.
When the pipeline links are disconnected through the media device
the FIMC and any sensor inherited controls are destroyed and then
again created when the pipeline connection completes.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a prerequisite for the patch converting the driver to use
the control framework. As the capture driver does not use per file
handle contexts, two separate ioctl handlers are created for it
(vidioc_try_fmt_mplane, and vidioc_g_fmt_mplane) so there is no
handlers shared between the memory-to-memory and capture video node.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a top level media device driver aggregating FIMC video devnodes,
MIPI-CSIS and sensor subdevs. This driver gathers all media entities
and creates the possible links between them during initialization. By
default some links will be activated to enable access to all available
sensors in the system. For example if there are sensors S0, S1 listed
in the media device platform data definition they will be by default
assigned to FIMC0, FIMC1 respectively, which in turn will corresponds
to separate /dev/video?.
There is enough FIMC H/W entities to cover all available physical camera
interfaces in the system.
The fimc media device driver is bound to the "s5p-fimc-md" platform device.
Such platform device should be created by board initialization code
and camera sensors description array need to be specified as its
platform data.
The media device driver also implements various video pipeline operations,
for enabling subdevs power, streaming, etc., which will be used by the
capture video node driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently there is a v4l2_device instance being registered per each
(capture and memory-to-memory) video node created per FIMC H/W instance.
This patch is a prerequisite for using the top level v4l2_device
instantiated by the media device driver.
To retain current debug trace semantic (so it's possible to distinguish
between the capture and m2m FIMC) the video_device is used in place
of v4l2_device where appropriate.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sensor subdevs need to be shared between all available FIMC instances.
Remove their registration from FIMC capture driver so they can then be
registered to the media device driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current driver allowed camera sensors to be used only with single
FIMC H/W instance, FIMC0..FIMC2/3, designated at compile time. Remaining FIMC
entities could be used for video processing only, as mem-to-mem devices.
Required camera could be selected with S_INPUT ioctl at one devnode only.
However in that case it was not possible to use both cameras independently
at the same time, as all sensors were registered to single FIMC capture
driver. In most recent S5P SoC version there is enough FIMC H/W instances
to cover all physical camera interfaces.
Each FIMC instance exports its own video devnode. Thus we distribute
the camera sensors one per each /dev/video? by default. It will allow to
use both camera simultaneously by opening different video node.
The camera sensors at FIMC are now not selected with S_INPUT ioctl, there
is one input only available per /dev/video?.
By default a single sensor is connected at FIMC input as specified by the
media device platform data subdev description table. This assignment
can be changed at runtime through the pipeline reconfiguration at the media
device level.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are 2 separate clock outputs available in the SoC for external sensors.
These two clocks can be shared among all FIMC entities and there is
currently no any arbitration of the clocks in the driver.
So make the capture driver not touching these clocks and let them be
be properly handled at the media device driver level, enabling proper
arbitration between FIMC entities.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not register video nodes during FIMC device probe. Also make
fimc_register_m2m_device() public for use by the media device driver.
The video nodes are to be registered during the media device driver
initialization, altogether with the subdev devnodes. The video
capture nodes need to be registered as last ones when the remaining
pipeline elements are already initialized.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add intialization of the media entities for video capture
and mem-to-mem video nodes. The mem-to-mem entity has no pads
whereas the capture entity has single sink pad.
Also clean up the video node naming for consistency.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not resume the device during system resume if it was idle
before system suspend, as this causes resume from suspend
to RAM failures on Exynos4. For this purpose runtime PM and
system sleep helpers are separated.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On the SoCs this driver is intended to support the are three separate
pins to supply the MIPI-CSIS subsystem: 1.1V or 1.2V, 1.8V and power
supply for an internal PLL.
This patch adds support for two separate voltage supplies to cover
properly board configurations where PMIC requires to configure
independently each external supply of the MIPI-CSI device. The 1.8V
and PLL supply are assigned a single "vdd18" regulator supply name
as it seems more reasonable than creating separate regulator supplies
for them.
While at here stop using the 'fixed_phy_vdd' platform_data field.
It has been introduced for boards where the MIPI-CSIS supplies are
not controllable. However it is not needed as those boards can use
the dummy regulator.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add runtime PM and system sleep support in the memory-to-memory
driver. It's required to enable the FIMC operation on Exynos4
SoCs. This patch prevents system boot failure when the driver
is compiled in, as it now tries to access its I/O memory without
first enabling the corresponding power domain.
The camera capture device suspend/resume is not fully covered,
the capture device is just powered on/off during the video
node open/close. However this enables it's normal operation
on Exynos4 SoCs.
[mchehab@redhat.com: fix a small checkpatch error]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch changes the order of operations during stream on call. Now the
buffers are first queued to the driver and then the start_streaming method
is called.
This resolves the most common case when the driver needs to know buffer
addresses to enable dma engine and start streaming. Additional parameter
to start_streaming method have been added to simplify drivers code. The
driver are now obliged to check if the number of queued buffers is high
enough to enable hardware streaming. If not - it can return an error. In
such case all the buffers that have been pre-queued are invalidated.
This patch also updates all videobuf2 clients to work properly with the
changed order of operations.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
CC: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
CC: Hans Verkuil <hverkuil@xs4all.nl>
CC: Tomasz Stanislawski <t.stanislaws@samsung.com>
CC: Sylwester Nawrocki <s.nawrocki@samsung.com>
CC: Kamil Debski <k.debski@samsung.com>
CC: Jonathan Corbet <corbet@lwn.net>
CC: Josh Wu <josh.wu@atmel.com>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Paul Mundt <lethal@linux-sh.org>
Tested-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the correct 'dma_addr' name for the buffer address. 'paddr' suggested
that this is the physical address in system memory. For most ARM platforms
these two are the same, but this is not a generic rule. 'dma_addr' will
also point better to dma-mapping api.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Plane sizes array was declared as unsigned long[], while unsigned int is
more than enough for storing size of the video buffer. This patch reduces
the size of the array by definiting it as unsigned int[].
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
MAPPED flag was set for the buffer only if all it's planes were mapped and
relied on a simple mapping counter. This assumption is really bogus,
especially because the buffers may be mapped multiple times. Also the
meaning of this flag for muliplane buffers was not really useful. This
patch fixes this issue by setting the MAPPED flag for the buffer if any of
it's planes is in use (what means that has been mapped at least once), so
MAPPED flag can be used as 'in_use' indicator.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Videobuf2 accepted any userptr buffer without verifying if its size is
large enough to store the video data from the driver. The driver reports
the minimal size of video data once in queue_setup and expects that
videobuf2 provides buffers that match these requirements. This patch
adds the required check.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the possible NULL pointer dereference in mem2mem
code.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes an implicit conversion between multi and single plane
formats from V4L2 framework. The conversion is to be performed by libv4l2.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
explicitly instead of using a macro.
ioctls and the ENUMSTD, S_STD and G_PARM ioctls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The service_set field of struct v4l2_sliced_vbi_cap was never filled in.
The v4l2-compliance tool complained about this, so this is now fixed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The colorspace was never filled in, causing complaints from v4l2-compliance.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Oberritter <obi@linuxtv.org> has looked at this and agreed that it is
safe to remove the 'timeout' variable.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tobias Lorenz <tobias.lorenz@gmx.net> has looked at this and agreed that the
'buf' variable could be removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is indeed a bug: balance and volume must be used to set the left and right
channel volume. Fixed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Removed the unused Xtal_Int variable. That made it also possible to remove a
related function. However, the code of that function has been preserved in a
comment describing an equation. Without that function that comment would
have been hard to understand.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
'off' was unused and 'ret' really had to be used to return -EFAULT.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The fix is to check for ret and return -EFAULT if non-zero.
I also noticed that write() didn't return the number of bytes written.
Fixed as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
refactor MFE code to allow for individual streaming configuration
for each frontend
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds new driver, mxl111sf, to support the WinTV-Aero-M
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Reviewed-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix division by zero in drxd triggered by running "femon" before any DVB
tuning has been done (by "scandvb" or anything else).
Signed-off-by: Edward Sheldrake <ejsheldrake@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add pr_fmt.
Convert usb style logging macros to pr_<level>.
Remove now unused old usb style logging macros.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sylwester Nawrocki
Marek Szyprowski
Yu Tang
Andrzej Pietrasiewicz
Tomasz Stanislawski
Hans Verkuil
Michael Krufky
Edward Sheldrake
Joe Perches
Andreas Oberritter