Commit Graph

1108 Commits

Author SHA1 Message Date
Girish K S 49bb1e6195 mmc: sdhci-s3c: Fix mmc card I/O problem
This patch fixes the problem in sdhci-s3c host driver for Samsung Soc's.
During the card identification stage the mmc core driver enumerates for
the best bus width in combination with the highest available data rate.
It starts enumerating from the highest bus width (8) to lowest width (1).

In case of few MMC cards the 4-bit bus enumeration fails and tries
the 1-bit bus enumeration. When switched to 1-bit bus mode the host driver
has to clear the previous bus width setting and apply the new setting.

The current patch will clear the previous bus mode and apply the new
mode setting.

Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-31 16:25:52 -04:00
Simon Horman b91df1593e mmc: sdhi: initialise mmc_data->flags before use
This corrects a logic error that I introduced in
"mmc: sdhi: Add write16_hook"

Reported-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-31 16:25:51 -04:00
Shawn Guo 66506f7617 mmc: sdhci-esdhc-imx: add missing inclusion of linux/module.h
There are the following warnings and errorx when compiling the driver.
The patch adds the missing inclusion of linux/module.h to fix them.

drivers/mmc/host/sdhci-esdhc-imx.c:563:12: error: ‘THIS_MODULE’ undeclared here (not in a function)
[..]

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-28 14:10:00 -04:00
Seungwon Jeon 6daa777866 mmc: dw_mmc: Fix DDR mode support.
Host driver can't get a hint of DDR mode through ios->ddr flag anymore.
ios->timing is currently used to inform DDR mode as a substitute.
And capability of MMC_CAP_MMC_HIGHSPEED is added for DDR support.

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:32 -04:00
Andy Shevchenko 65be3fef93 mmc: sdhci: use f_max instead of host->clock for timeouts
When timeout_clk is calculated the host->clock could be zero.
So, instead of host->clock the calculation now uses mmc->f_max.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:30 -04:00
Andy Shevchenko 272308caaa mmc: sdhci: move timeout_clk calculation farther down
This moves the calculation below the assignment of mmc->f_max, which
we need for calculating timeout_clk in the next patch in this series.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:29 -04:00
Andy Shevchenko 78a2ca2727 mmc: sdhci: check host->clock before using it as a denominator
Sometimes host->clock could be zero which is a legal situation. This
patch checks host->clock before usage as a denominator when timeout is
calculated. A similar patch is applied for mmc core (see commit e9b8684,
"mmc: fix division by zero in MMC core").

Without this patch, the execution of the sdhci_calc_timeout could end up
with a backtrace:

<0>[    4.014319] divide error: 0000 [#1] PREEMPT SMP
<4>[    4.014352] Modules linked in: g_ether
<4>[    4.014376]
<4>[    4.014393] Pid: 33, comm: kworker/u:2 Not tainted 3.0.0+ #646
<4>[    4.014421] EIP: 0060:[<c12fa38e>] EFLAGS: 00010046 CPU: 1
<4>[    4.014449] EIP is at sdhci_calc_timeout+0x2e/0x100
<4>[    4.014468] EAX: 00000000 EBX: f5930fc8 ECX: 00000000 EDX: 00000000
<4>[    4.014488] ESI: f5291de8 EDI: f5291db8 EBP: f5291c6c ESP: f5291c50
<4>[    4.014508]  DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
<0>[    4.014529] Process kworker/u:2 (pid: 33, ti=f5290000 task=f53065a0 task.ti=f5290000)
<0>[    4.014546] Stack:
<4>[    4.014557]  00000082 c1054fdd f5291c78 04000000 f5930fc8 f5291de8 f5291db8 f5291cac
<4>[    4.014611]  c12fab7c c107a98b f5291c88 c13b6d3f f593109c f5882000 f5291cac c1054fdd
<4>[    4.014663]  00000000 00000000 f5882000 00000082 f5930fc8 f5291db8 0000000a f5291ccc
<0>[    4.014716] Call Trace:
<4>[    4.014743]  [<c1054fdd>] ? mod_timer+0x11d/0x380
<4>[    4.014770]  [<c12fab7c>] sdhci_prepare_data+0x2c/0x3a0
<4>[    4.014798]  [<c107a98b>] ? trace_hardirqs_off+0xb/0x10
<4>[    4.014827]  [<c13b6d3f>] ? _raw_spin_unlock_irqrestore+0x2f/0x60
<4>[    4.014854]  [<c1054fdd>] ? mod_timer+0x11d/0x380
<4>[    4.014880]  [<c12fc7db>] sdhci_send_command+0xdb/0x210
<4>[    4.014906]  [<c12fd5f3>] sdhci_request+0xc3/0x150
<4>[    4.014932]  [<c12ec56a>] mmc_start_request+0xda/0x200
<4>[    4.014960]  [<c120d7c2>] ? __raw_spin_lock_init+0x32/0x60
<4>[    4.014989]  [<c1066a85>] ? __init_waitqueue_head+0x35/0x50
<4>[    4.015015]  [<c12ec70b>] mmc_wait_for_req+0x7b/0x90
<4>[    4.015045]  [<c12f0c67>] mmc_send_cxd_data+0xf7/0x130
<4>[    4.015076]  [<c12ecbc0>] ? mmc_erase+0x140/0x140
<4>[    4.015102]  [<c12f139d>] mmc_send_ext_csd+0x1d/0x20
<4>[    4.015125]  [<c12efef0>] mmc_get_ext_csd+0x70/0x140
<4>[    4.015151]  [<c12effe8>] mmc_compare_ext_csds+0x28/0x190
<4>[    4.015176]  [<c12f039f>] mmc_init_card+0x24f/0x650
<4>[    4.015201]  [<c13b6d5d>] ? _raw_spin_unlock_irqrestore+0x4d/0x60
<4>[    4.015226]  [<c107fd9c>] ? trace_hardirqs_on_caller+0x11c/0x160
<4>[    4.015255]  [<c12f09a4>] mmc_attach_mmc+0xa4/0x190
<4>[    4.015282]  [<c12ee3f0>] mmc_rescan+0x210/0x240
<4>[    4.015311]  [<c105f9b6>] process_one_work+0x176/0x550
<4>[    4.015336]  [<c105f93a>] ? process_one_work+0xfa/0x550
<4>[    4.015360]  [<c12ee1e0>] ? mmc_init_erase+0x140/0x140
<4>[    4.015385]  [<c1061c2a>] worker_thread+0x12a/0x2c0
<4>[    4.015410]  [<c1061b00>] ? manage_workers.clone.18+0x100/0x100
<4>[    4.015437]  [<c1066244>] kthread+0x74/0x80
<4>[    4.015463]  [<c10661d0>] ? __init_kthread_worker+0x60/0x60
<4>[    4.015490]  [<c13b7dfa>] kernel_thread_helper+0x6/0xd
<0>[    4.015507] Code: 57 89 d7 56 53 89 c3 83 ec 10 8b 40 04 8b 72 28 f6 c4 10 89 45 f0 0f 85 91 00 00 00 85 f6 0f 84 c1 00 00 00 8b 4e 04 31 d2 89 c8 <f7> 73 58 ba d3 4d 62 10 89 c1 8b 06 f7 e2 c1 ea 06 01 d1 f7 45
<0>[    4.015829] EIP: [<c12fa38e>] sdhci_calc_timeout+0x2e/0x100 SS:ESP 0068:f5291c50

Reported-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:28 -04:00
Andy Shevchenko 83cbcd93a1 mmc: Revert "mmc: sdhci: Fix SDHCI_QUIRK_TIMEOUT_USES_SDCLK"
This reverts commit 4b01681c77, which introduced a new potential
divide by zero in the process of fixing one.  The subsequent commits
attempt to fix the issue properly.

Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:27 -04:00
Axel Lin 4906baf080 mmc: tmio: eliminate unused variable 'mmc' warning
Fix below compile warning:
  CC      drivers/mmc/host/tmio_mmc.o
drivers/mmc/host/tmio_mmc.c: In function 'tmio_mmc_suspend':
drivers/mmc/host/tmio_mmc.c:30: warning: unused variable 'mmc'
drivers/mmc/host/tmio_mmc.c: In function 'tmio_mmc_resume':
drivers/mmc/host/tmio_mmc.c:45: warning: unused variable 'mmc'

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:27 -04:00
Tony Lin 0d58864bf3 mmc: esdhc-imx: fix card interrupt loss on freescale eSDHC
Apply a workaround for the imx eSDHC controller to avoid missing
card interrupts.  This makes SDIO work.

Signed-off-by: Tony Lin <tony.lin@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:26 -04:00
Mark Brown 55156d240a mmc: sdhci-s3c: Fix build for header change
A header change has removed an implicit inclusion of module.h, breaking
the build due to the use of THIS_MODULE. Fix that.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:25 -04:00
Shashidhar Hiremath 9b7bbe1085 mmc: dw_mmc: Fix mask in IDMAC_SET_BUFFER1_SIZE macro
The mask used inside this macro was assuming Buffer_Size1's [BS1's]
width to be 14 bits, it is actually 13 bits.  Modify masks used in
IDMAC_SET_BUFFER1_SIZE such that they use only 13 bits instead of
current 14.

Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:24 -04:00
Jaehoon Chung 7199e2b61d mmc: sdhci-s3c: add BROKEN_ADMA_ZEROLEN_DESC quirk
Samsung SoCs need to set BROKEN_ADMA_ZEROLEN_DESC.
(If ADMA operation is more than 65535, maybe set by zero.)

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:21 -04:00
Philip Rakity 606a15e475 mmc: sdhci: pxav3: controller needs 32 bit ADMA addressing
Enable the quirk.

(Best used in conjunction with patch downgrading ADMA to SDMA when
transfer is not aligned.)

Signed-off-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:20 -04:00
Aaron Lu 78869618a8 mmc: sdhci: fix retuning timer wrongly deleted in sdhci_tasklet_finish
Currently, the retuning timer for retuning mode 1 will be deleted in
function sdhci_tasklet_finish after a mmc request done, which will make
retuning timing never trigger again. This patch fixed this problem.

Signed-off-by: Aaron Lu <Aaron.Lu@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:19 -04:00
Shawn Guo abfafc2d10 mmc: sdhci-esdhc-imx: add device tree probe support
The patch adds device tree probe support for sdhci-esdhc-imx driver.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Chris Ball <cjb@laptop.org>
2011-07-27 09:31:39 +08:00
Shawn Guo a4d2177f00 mmc: sdhci-pltfm: dt device does not pass parent to sdhci_alloc_host
Neither platform based nor dt based device needs to pass the parent
to sdhci_alloc_host.  There is no difference between platform and dt
on this point.

The patch makes the change to pass device itself than its parent to
sdhci_alloc_host for dt case too.  Otherwise the probe function of
sdhci based drivers which is shared between platform and dt will
fail on dt case.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Chris Ball <cjb@laptop.org>
2011-07-27 09:31:33 +08:00
Shawn Guo 57ed3314e0 mmc: sdhci-esdhc-imx: get rid of the uses of cpu_is_mx()
The patch removes all the uses of cpu_is_mx().  Instead, it utilizes
platform_device_id to distinguish the esdhc differences among SoCs.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Chris Ball <cjb@laptop.org>
2011-07-27 09:31:27 +08:00
Shawn Guo 842afc02cf mmc: sdhci-esdhc-imx: do not reference platform data after probe
The patch copies platform data into pltfm_imx_data and reference
the data there than platform data after probe.

This work is inspired by Grant Likely and Troy Kisky.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Chris Ball <cjb@laptop.org>
2011-07-27 09:31:21 +08:00
Shawn Guo 913413c307 mmc: sdhci-esdhc-imx: extend card_detect and write_protect support for mx5
The patch extends card_detect and write_protect support to get mx5
family and more scenarios supported.  The changes include:

 * Turn platform_data from optional to mandatory
 * Add cd_types and wp_types into platform_data to cover more use
   cases
 * Remove the use of flag ESDHC_FLAG_GPIO_FOR_CD
 * Adjust some machine codes to adopt the platform_data changes
 * Work around the issue that software reset will get card detection
   circuit stop working

With this patch, card_detect and write_protect gets supported on
mx5 based platforms.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Chris Ball <cjb@laptop.org>
2011-07-27 09:31:14 +08:00
Rafael J. Wysocki 6c0cbef666 MMC / TMIO: Fix build issue related to struct scatterlist
Fix build issue caused by undefined struct scatterlist in
drivers/mmc/host/tmio_mmc.c.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-07-26 11:52:55 -07:00
Linus Torvalds d3ec4844d4 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
  fs: Merge split strings
  treewide: fix potentially dangerous trailing ';' in #defined values/expressions
  uwb: Fix misspelling of neighbourhood in comment
  net, netfilter: Remove redundant goto in ebt_ulog_packet
  trivial: don't touch files that are removed in the staging tree
  lib/vsprintf: replace link to Draft by final RFC number
  doc: Kconfig: `to be' -> `be'
  doc: Kconfig: Typo: square -> squared
  doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
  drivers/net: static should be at beginning of declaration
  drivers/media: static should be at beginning of declaration
  drivers/i2c: static should be at beginning of declaration
  XTENSA: static should be at beginning of declaration
  SH: static should be at beginning of declaration
  MIPS: static should be at beginning of declaration
  ARM: static should be at beginning of declaration
  rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
  Update my e-mail address
  PCIe ASPM: forcedly -> forcibly
  gma500: push through device driver tree
  ...

Fix up trivial conflicts:
 - arch/arm/mach-ep93xx/dma-m2p.c (deleted)
 - drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
 - drivers/net/r8169.c (just context changes)
2011-07-25 13:56:39 -07:00
Linus Torvalds dd58ecba48 Merge branch 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (35 commits)
  ARM: msm: platsmp: determine number of CPU cores at boot time
  ARM: Tegra: Seaboard: Fix I2C bus numbering for ADT7461
  ARM: Tegra: Trimslice: Tri-state DAP3 pinmux
  ARM: orion5x: fixup 5181 MPP mask check
  ARM: mxs-dma: include <linux/dmaengine.h>
  ARM: i.MX53: consistently use MX53_UART_PAD_CTRL for uart txd/rxd/rts/cts
  ARM: i.MX53: UARTn_CTS pin should not change RTS input select
  ARM: i.MX53: UARTn_TXD pin should not change RXD input select
  ARM: mx25: Fix typo on CAN1_RX pad setting
  iomux-mx53: add missing 'IOMUX_CONFIG_SION' for some I2C pad definitions
  ARM: NUC93X: add UL suffix to VMALLOC_END to ensure it is properly typed
  ARM: LPC32XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
  ARM: CNS3XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
  ARM: i.MX53: Fix IOMUX type o's
  ARM i.MX dma: Fix burstsize settings
  mach-mx5: fix the I2C clock parents
  ARM: mxs/tx28: according to the TX28's datasheet D4-D7 are not used for MMC0
  ARM i.MX23/28: platform-mxsfb: Add missing include of linux/dma-mapping.h
  ARM: mx53: Fix some interrupts marked as reserved.
  MXC: iomux-v3: correct NO_PAD_CTRL definition
  ...

Fix up trivial conflict in arch/arm/mach-imx/mach-mx31_3ds.c
2011-07-25 11:53:35 -07:00
Linus Torvalds b6844e8f64 Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits)
  ARM: 7004/1: fix traps.h compile warnings
  ARM: 6998/2: kernel: use proper memory barriers for bitops
  ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM
  ARM: Fix build errors caused by adding generic macros
  ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU
  ARM: CPU hotplug: pass in proper affinity mask on IRQ migration
  ARM: GIC: avoid routing interrupts to offline CPUs
  ARM: CPU hotplug: fix abuse of irqdesc->node
  ARM: 6981/2: mmci: adjust calculation of f_min
  ARM: 7000/1: LPAE: Use long long printk format for displaying the pud
  ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state
  ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence
  ARM: ARM_DMA_ZONE_SIZE is no more
  ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ...
2011-07-24 10:20:54 -07:00
Russell King 06f365acef Merge branches 'btc', 'dma', 'entry', 'fixes', 'linker-layout', 'misc', 'mmci', 'suspend' and 'vfp' into for-next 2011-07-22 23:08:48 +01:00
Linus Torvalds 951cc93a74 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1287 commits)
  icmp: Fix regression in nexthop resolution during replies.
  net: Fix ppc64 BPF JIT dependencies.
  acenic: include NET_SKB_PAD headroom to incoming skbs
  ixgbe: convert to ndo_fix_features
  ixgbe: only enable WoL for magic packet by default
  ixgbe: remove ifdef check for non-existent define
  ixgbe: Pass staterr instead of re-reading status and error bits from descriptor
  ixgbe: Move interrupt related values out of ring and into q_vector
  ixgbe: add structure for containing RX/TX rings to q_vector
  ixgbe: inline the ixgbe_maybe_stop_tx function
  ixgbe: Update ATR to use recorded TX queues instead of CPU for routing
  igb: Fix for DH89xxCC near end loopback test
  e1000: always call e1000_check_for_link() on e1000_ce4100 MACs.
  netxen: add fw version compatibility check
  be2net: request native mode each time the card is reset
  ipv4: Constrain UFO fragment sizes to multiples of 8 bytes
  virtio_net: Fix panic in virtnet_remove
  ipv6: make fragment identifications less predictable
  ipv6: unshare inetpeers
  can: make function can_get_bittiming static
  ...
2011-07-22 14:43:13 -07:00
Jean-Christophe PLAGNIOL-VILLARD b0a68ec944 mmc: at91_mci: move register header from include/ to drivers/
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:08 -04:00
Koen Beel d982dcdc4e mmc: mxs-mmc: fix clock rate setting
Fix clock rate setting in the mxs-mmc driver. Previously, if div2 was 0
then the value for TIMING_CLOCK_RATE would have been 255 instead of 0.
The limits for div1 (TIMING_CLOCK_DIVIDE) and div2 (TIMING_CLOCK_RATE+1)
were also not correctly defined.

Can easily be reproduced on mx23evk: default clock for high speed sdio
cards is 50 MHz. With a SSP_CLK of 28.8 MHz default), this resulted in
an actual clock rate of about 56 kHz.  Tested on mx23evk.

Signed-off-by: Koen Beel <koen.beel@barco.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:08 -04:00
Guennadi Liakhovetski 162f43e31c mmc: tmio: fix a deadlock
Currently the tmio-mmc driver contains a recursive runtime PM method
invocation, which leads to a deadlock on a mutex. Avoid it by taking
care not to request DMA too early.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:07 -04:00
Guennadi Liakhovetski 332bdb506f mmc: tmio: fix a recently introduced bug in DMA code
A recent commit "mmc: tmio: Share register access functions" has swapped
arguments of a macro and broken DMA with TMIO MMC. This patch fixes the
arguments back.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:07 -04:00
Guennadi Liakhovetski c9b0cef23f mmc: sh_mmcif: maximize power saving
This patch uses runtime PM to allow the system to power down the MMC
controller, when the MMC closk is switched off.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:06 -04:00
Guennadi Liakhovetski 71d111cd34 mmc: tmio: maximize power saving
This patch uses runtime PM to allow the system to power down the MMC
controller, when the MMC closk is switched off.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:06 -04:00
Guennadi Liakhovetski b9269fdd4f mmc: tmio: fix recursive spinlock, don't schedule with interrupts disabled
Calling mmc_request_done() under a spinlock with interrupts disabled
leads to a recursive spin-lock on request retry path and to
scheduling in atomic context. This patch fixes both these problems
by moving mmc_request_done() to the scheduler workqueue.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:05 -04:00
Adrian Hunter 770d743200 mmc: omap_hsmmc: fix oops in omap_hsmmc_dma_cb()
In the case of an I/O error, the DMA will have been cleaned up in
the MMC interrupt and the request structure pointer will be null.

In that case, it is essential to check if the DMA is over before
dereferencing host->mrq->data.

Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:04 -04:00
Andy Shevchenko 3796fb8ac4 mmc: omap_hsmmc: refactor duplicated code
There are a few places with the same functionality. This patch creates
two functions omap_hsmmc_set_bus_width() and omap_hsmmc_set_bus_mode()
to do the job.

Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:03 -04:00
Andy Shevchenko 5934df2f10 mmc: omap_hsmmc: fix a few bugs when setting the clock divisor
There are two pieces of code which are similar, but not the same.
Each of them contains a bug.

The SYSCTL register should be read before writing to it in
omap_hsmmc_context_restore() to retain the state of the reserved bits.

Before setting the clock divisor and DTO bits the value from the SYSCTL
register should be masked properly. We were lucky to have no problems
with DTO bits. So, make sure we have clear DTO bits properly in
omap_hsmmc_set_ios().

Additionally get rid of msleep(1). The actual time is rarely higher
than 30us on OMAP 3630.

The resulting pieces of code are refactored into the
omap_hsmmc_set_clock() function.

Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:03 -04:00
Andy Shevchenko e0c7f99b86 mmc: omap_hsmmc: introduce start_clock and re-use stop_clock
There is similar code in two functions which enable the clock.  Refactor
this code to omap_hsmmc_start_clock(). Re-use omap_hsmmc_stop_clock() in
omap_hsmmc_context_restore() as well.

Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:02 -04:00
Andy Shevchenko ac330f44c6 mmc: omap_hsmmc: split duplicate code to calc_divisor() function
There are two places where the same calculations are done.
Let's split them into a separate function.

In addition, simplify by using the DIV_ROUND_UP kernel macro.

Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:02 -04:00
Andy Shevchenko 6b206efecc mmc: omap_hsmmc: move hardcoded frequency constants to defines
Move the min and max frequency constants to the definition block in
the source file.

Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:01 -04:00
Adrian Hunter 699b958ba0 mmc: omap_hsmmc: correct debug report error status mnemonics
CERR and BADA were in the wrong place and there are only
32 not 35.

Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:01 -04:00
Balaji T K 101ed47e01 mmc: omap_hsmmc: Remove unused iclk
After runtime conversion to handle clk, iclk node is not used.
However fclk node is still used to get clock rate.

Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:21:17 -04:00
Balaji T K fa4aa2d48d mmc: omap_hsmmc: add runtime pm support
* Add runtime pm support to HSMMC host controller.
* Use runtime pm API to enable/disable HSMMC clock.
* Use runtime autosuspend APIs to enable auto suspend delay.

Based on OMAP HSMMC runtime implementation by Kevin Hilman and
Kishore Kadiyala.

Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:21:17 -04:00
Balaji T K 7a8c2cef3d mmc: omap_hsmmc: Remove lazy_disable
lazy_disable framework in OMAP HSMMC manages multiple low power states and
card is powered off after inactivity time of 8 seconds.  Based on previous
discussion on the list, card power (regulator) handling (when to power
OFF/ON) should ideally be handled by core layer.  Remove usage of lazy
disable to allow core layer _only_ to handle card power.  With the removal
of lazy disable framework, MMC regulators are left ON until MMC_POWER_OFF
via set_ios.

Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:21:16 -04:00
Per Forlin 58c7ccbf91 mmc: mmci: implement pre_req() and post_req()
pre_req() runs dma_map_sg() and prepares the dma descriptor for the next
mmc data transfer. post_req() runs dma_unmap_sg.  If not calling pre_req()
before mmci_request(), mmci_request() will prepare the cache and dma just
like it did it before.  It is optional to use pre_req() and post_req()
for mmci.

Signed-off-by: Per Forlin <per.forlin@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:21:11 -04:00
Per Forlin 9782aff8df mmc: omap_hsmmc: add support for pre_req and post_req
pre_req() runs dma_map_sg(), post_req() runs dma_unmap_sg.  If not calling
pre_req() before omap_hsmmc_request(), dma_map_sg will be issued before
starting the transfer.  It is optional to use pre_req().  If issuing
pre_req(), post_req() must be called as well.

Signed-off-by: Per Forlin <per.forlin@linaro.org>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:21:10 -04:00
Nicolas Ferre 5c209f1fb7 mmc: kconfig: remove EXPERIMENTAL from the DMA selection of atmel-mci
This driver has been used for years with this option enabled.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:21:09 -04:00
Nicolas Ferre 5c2f2b9bd0 mmc: atmel-mci: add suspend/resume support
Take care of slots while going to suspend state.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:21:08 -04:00
Adrian Hunter 0d013bcf5c mmc: sdhci-pci: allow 8-bit bus width for Intel Medfield eMMCs
Unless MMC_CAP_8_BIT_DATA is set, the bus width defaults to 4.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:21:07 -04:00
Major Lee 68077b0261 mmc: sdhci-pci: add 8-bit bus width support for mrst hc0
And hook platform_8bit_width to support 8-bit bus width.

Signed-off-by: Major Lee <major_lee@wistron.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:21:07 -04:00
James Hogan 94dd5b3371 mmc: dw_mmc: reset FIFO after an error
If an error occurs mid way through a transaction (such as a missing CRC
status response after the 2nd block written out of 3), then the FIFO may
still contain data which will interfere with the next transaction.
Therefore after an error has been detected, reset the fifo using the
CTRL register.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:21:06 -04:00