The current memory hotplug implementation relies on having all the
struct pages associate with a zone/node during the physical hotplug
phase (arch_add_memory->__add_pages->__add_section->__add_zone). In the
vast majority of cases this means that they are added to ZONE_NORMAL.
This has been so since 9d99aaa31f ("[PATCH] x86_64: Support memory
hotadd without sparsemem") and it wasn't a big deal back then because
movable onlining didn't exist yet.
Much later memory hotplug wanted to (ab)use ZONE_MOVABLE for movable
onlining 511c2aba8f ("mm, memory-hotplug: dynamic configure movable
memory and portion memory") and then things got more complicated.
Rather than reconsidering the zone association which was no longer
needed (because the memory hotplug already depended on SPARSEMEM) a
convoluted semantic of zone shifting has been developed. Only the
currently last memblock or the one adjacent to the zone_movable can be
onlined movable. This essentially means that the online type changes as
the new memblocks are added.
Let's simulate memory hot online manually
$ echo 0x100000000 > /sys/devices/system/memory/probe
$ grep . /sys/devices/system/memory/memory32/valid_zones
Normal Movable
$ echo $((0x100000000+(128<<20))) > /sys/devices/system/memory/probe
$ grep . /sys/devices/system/memory/memory3?/valid_zones
/sys/devices/system/memory/memory32/valid_zones:Normal
/sys/devices/system/memory/memory33/valid_zones:Normal Movable
$ echo $((0x100000000+2*(128<<20))) > /sys/devices/system/memory/probe
$ grep . /sys/devices/system/memory/memory3?/valid_zones
/sys/devices/system/memory/memory32/valid_zones:Normal
/sys/devices/system/memory/memory33/valid_zones:Normal
/sys/devices/system/memory/memory34/valid_zones:Normal Movable
$ echo online_movable > /sys/devices/system/memory/memory34/state
$ grep . /sys/devices/system/memory/memory3?/valid_zones
/sys/devices/system/memory/memory32/valid_zones:Normal
/sys/devices/system/memory/memory33/valid_zones:Normal Movable
/sys/devices/system/memory/memory34/valid_zones:Movable Normal
This is an awkward semantic because an udev event is sent as soon as the
block is onlined and an udev handler might want to online it based on
some policy (e.g. association with a node) but it will inherently race
with new blocks showing up.
This patch changes the physical online phase to not associate pages with
any zone at all. All the pages are just marked reserved and wait for
the onlining phase to be associated with the zone as per the online
request. There are only two requirements
- existing ZONE_NORMAL and ZONE_MOVABLE cannot overlap
- ZONE_NORMAL precedes ZONE_MOVABLE in physical addresses
the latter one is not an inherent requirement and can be changed in the
future. It preserves the current behavior and made the code slightly
simpler. This is subject to change in future.
This means that the same physical online steps as above will lead to the
following state: Normal Movable
/sys/devices/system/memory/memory32/valid_zones:Normal Movable
/sys/devices/system/memory/memory33/valid_zones:Normal Movable
/sys/devices/system/memory/memory32/valid_zones:Normal Movable
/sys/devices/system/memory/memory33/valid_zones:Normal Movable
/sys/devices/system/memory/memory34/valid_zones:Normal Movable
/sys/devices/system/memory/memory32/valid_zones:Normal Movable
/sys/devices/system/memory/memory33/valid_zones:Normal Movable
/sys/devices/system/memory/memory34/valid_zones:Movable
Implementation:
The current move_pfn_range is reimplemented to check the above
requirements (allow_online_pfn_range) and then updates the respective
zone (move_pfn_range_to_zone), the pgdat and links all the pages in the
pfn range with the zone/node. __add_pages is updated to not require the
zone and only initializes sections in the range. This allowed to
simplify the arch_add_memory code (s390 could get rid of quite some of
code).
devm_memremap_pages is the only user of arch_add_memory which relies on
the zone association because it only hooks into the memory hotplug only
half way. It uses it to associate the new memory with ZONE_DEVICE but
doesn't allow it to be {on,off}lined via sysfs. This means that this
particular code path has to call move_pfn_range_to_zone explicitly.
The original zone shifting code is kept in place and will be removed in
the follow up patch for an easier review.
Please note that this patch also changes the original behavior when
offlining a memory block adjacent to another zone (Normal vs. Movable)
used to allow to change its movable type. This will be handled later.
[richard.weiyang@gmail.com: simplify zone_intersects()]
Link: http://lkml.kernel.org/r/20170616092335.5177-1-richard.weiyang@gmail.com
[richard.weiyang@gmail.com: remove duplicate call for set_page_links]
Link: http://lkml.kernel.org/r/20170616092335.5177-2-richard.weiyang@gmail.com
[akpm@linux-foundation.org: remove unused local `i']
Link: http://lkml.kernel.org/r/20170515085827.16474-12-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Reza Arbab <arbab@linux.vnet.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> # For s390 bits
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Daniel Kiper <daniel.kiper@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Tobias Regnery <tobias.regnery@gmail.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pagetypeinfo_showblockcount_print skips over invalid pfns but it would
report pages which are offline because those have a valid pfn. Their
migrate type is misleading at best.
Now that we have pfn_to_online_page() we can use it instead of
pfn_valid() and fix this.
[mhocko@suse.com: fix build]
Link: http://lkml.kernel.org/r/20170519072225.GA13041@dhcp22.suse.cz
Link: http://lkml.kernel.org/r/20170515085827.16474-11-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Joonsoo Kim <js1304@gmail.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Daniel Kiper <daniel.kiper@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Reza Arbab <arbab@linux.vnet.ibm.com>
Cc: Tobias Regnery <tobias.regnery@gmail.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__first_valid_page skips over invalid pfns in the range but it might
still stumble over offline pages. At least start_isolate_page_range
will mark those set_migratetype_isolate. This doesn't represent any
immediate AFAICS because alloc_contig_range will fail to isolate those
pages but it relies on not fully initialized page which will become a
problem later when we stop associating offline pages to zones. Use
pfn_to_online_page to handle this.
This is more a preparatory patch than a fix.
Link: http://lkml.kernel.org/r/20170515085827.16474-10-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Daniel Kiper <daniel.kiper@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Reza Arbab <arbab@linux.vnet.ibm.com>
Cc: Tobias Regnery <tobias.regnery@gmail.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__reset_isolation_suitable walks the whole zone pfn range and it tries
to jump over holes by checking the zone for each page. It might still
stumble over offline pages, though. Skip those by checking
pfn_to_online_page()
Link: http://lkml.kernel.org/r/20170515085827.16474-9-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Daniel Kiper <daniel.kiper@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Reza Arbab <arbab@linux.vnet.ibm.com>
Cc: Tobias Regnery <tobias.regnery@gmail.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__pageblock_pfn_to_page has two users currently, set_zone_contiguous
which checks whether the given zone contains holes and
pageblock_pfn_to_page which then carefully returns a first valid page
from the given pfn range for the given zone. This doesn't handle zones
which are not fully populated though. Memory pageblocks can be offlined
or might not have been onlined yet. In such a case the zone should be
considered to have holes otherwise pfn walkers can touch and play with
offline pages.
Current callers of pageblock_pfn_to_page in compaction seem to work
properly right now because they only isolate PageBuddy
(isolate_freepages_block) or PageLRU resp. __PageMovable
(isolate_migratepages_block) which will be always false for these pages.
It would be safer to skip these pages altogether, though.
In order to do this patch adds a new memory section state
(SECTION_IS_ONLINE) which is set in memory_present (during boot time) or
in online_pages_range during the memory hotplug. Similarly
offline_mem_sections clears the bit and it is called when the memory
range is offlined.
pfn_to_online_page helper is then added which check the mem section and
only returns a page if it is onlined already.
Use the new helper in __pageblock_pfn_to_page and skip the whole page
block in such a case.
[mhocko@suse.com: check valid section number in pfn_to_online_page (Vlastimil),
mark sections online after all struct pages are initialized in
online_pages_range (Vlastimil)]
Link: http://lkml.kernel.org/r/20170518164210.GD18333@dhcp22.suse.cz
Link: http://lkml.kernel.org/r/20170515085827.16474-8-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Daniel Kiper <daniel.kiper@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Reza Arbab <arbab@linux.vnet.ibm.com>
Cc: Tobias Regnery <tobias.regnery@gmail.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
is_pageblock_removable_nolock() relies on having zone association to
examine all the page blocks to check whether they are movable or free.
This is just wasting of cycles when the memblock is offline. Later
patch in the series will also change the time when the page is
associated with a zone so we let's bail out early if the memblock is
offline.
Link: http://lkml.kernel.org/r/20170515085827.16474-7-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Daniel Kiper <daniel.kiper@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Reza Arbab <arbab@linux.vnet.ibm.com>
Cc: Tobias Regnery <tobias.regnery@gmail.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Memory hotplug (add_memory_resource) has to reinitialize node
infrastructure if the node is offline (one which went through the
complete add_memory(); remove_memory() cycle). That involves node
registration to the kobj infrastructure (register_node), the proper
association with cpus (register_cpu_under_node) and finally creation of
node<->memblock symlinks (link_mem_sections).
The last part requires to know node_start_pfn and node_spanned_pages
which we currently have but a leter patch will postpone this
initialization to the onlining phase which happens later. In fact we do
not need to rely on the early pgdat initialization even now because the
currently hot added pfn range is currently known.
Split register_one_node into core which does all the common work for the
boot time NUMA initialization and the hotplug (__register_one_node).
register_one_node keeps the full initialization while hotplug calls
__register_one_node and manually calls link_mem_sections for the proper
range.
This shouldn't introduce any functional change.
Link: http://lkml.kernel.org/r/20170515085827.16474-6-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Daniel Kiper <daniel.kiper@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Reza Arbab <arbab@linux.vnet.ibm.com>
Cc: Tobias Regnery <tobias.regnery@gmail.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Device memory hotplug hooks into regular memory hotplug only half way.
It needs memory sections to track struct pages but there is no
need/desire to associate those sections with memory blocks and export
them to the userspace via sysfs because they cannot be onlined anyway.
This is currently expressed by for_device argument to arch_add_memory
which then makes sure to associate the given memory range with
ZONE_DEVICE. register_new_memory then relies on is_zone_device_section
to distinguish special memory hotplug from the regular one. While this
works now, later patches in this series want to move __add_zone outside
of arch_add_memory path so we have to come up with something else.
Add want_memblock down the __add_pages path and use it to control
whether the section->memblock association should be done.
arch_add_memory then just trivially want memblock for everything but
for_device hotplug.
remove_memory_section doesn't need is_zone_device_section either. We
can simply skip all the memblock specific cleanup if there is no
memblock for the given section.
This shouldn't introduce any functional change.
Link: http://lkml.kernel.org/r/20170515085827.16474-5-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Daniel Kiper <daniel.kiper@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Reza Arbab <arbab@linux.vnet.ibm.com>
Cc: Tobias Regnery <tobias.regnery@gmail.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit c04fc586c1 ("mm: show node to memory section relationship with
symlinks in sysfs") has added means to export memblock<->node
association into the sysfs. It has also introduced get_nid_for_pfn
which is a rather confusing counterpart of pfn_to_nid which checks also
whether the pfn page is already initialized (page_initialized).
This is done by checking page::lru != NULL which doesn't make any sense
at all. Nothing in this path really relies on the lru list being used
or initialized. Just remove it because this will become a problem with
later patches.
Thanks to Reza Arbab for testing which revealed this to be a problem
(http://lkml.kernel.org/r/20170403202337.GA12482@dhcp22.suse.cz)
Link: http://lkml.kernel.org/r/20170515085827.16474-4-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Reza Arbab <arbab@linux.vnet.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Daniel Kiper <daniel.kiper@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Tobias Regnery <tobias.regnery@gmail.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The primary purpose of this helper is to query the node state so use the
node id directly. This is a preparatory patch for later changes.
This shouldn't introduce any functional change
Link: http://lkml.kernel.org/r/20170515085827.16474-3-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Daniel Kiper <daniel.kiper@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Reza Arbab <arbab@linux.vnet.ibm.com>
Cc: Tobias Regnery <tobias.regnery@gmail.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "mm: make movable onlining suck less", v4.
Movable onlining is a real hack with many downsides - mainly
reintroduction of lowmem/highmem issues we used to have on 32b systems -
but it is the only way to make the memory hotremove more reliable which
is something that people are asking for.
The current semantic of memory movable onlinening is really cumbersome,
however. The main reason for this is that the udev driven approach is
basically unusable because udev races with the memory probing while only
the last memory block or the one adjacent to the existing zone_movable
are allowed to be onlined movable. In short the criterion for the
successful online_movable changes under udev's feet. A reliable udev
approach would require a 2 phase approach where the first successful
movable online would have to check all the previous blocks and online
them in descending order. This is hard to be considered sane.
This patchset aims at making the onlining semantic more usable. First
of all it allows to online memory movable as long as it doesn't clash
with the existing ZONE_NORMAL. That means that ZONE_NORMAL and
ZONE_MOVABLE cannot overlap. Currently I preserve the original ordering
semantic so the zone always precedes the movable zone but I have plans
to remove this restriction in future because it is not really necessary.
First 3 patches are cleanups which should be ready to be merged right
away (unless I have missed something subtle of course).
Patch 4 deals with ZONE_DEVICE dependencies down the __add_pages path.
Patch 5 deals with implicit assumptions of register_one_node on pgdat
initialization.
Patches 6-10 deal with offline holes in the zone for pfn walkers. I
hope I got all of them right but people familiar with compaction should
double check this.
Patch 11 is the core of the change. In order to make it easier to
review I have tried it to be as minimalistic as possible and the large
code removal is moved to patch 14.
Patch 12 is a trivial follow up cleanup. Patch 13 fixes sparse warnings
and finally patch 14 removes the unused code.
I have tested the patches in kvm:
# qemu-system-x86_64 -enable-kvm -monitor pty -m 2G,slots=4,maxmem=4G -numa node,mem=1G -numa node,mem=1G ...
and then probed the additional memory by
(qemu) object_add memory-backend-ram,id=mem1,size=1G
(qemu) device_add pc-dimm,id=dimm1,memdev=mem1
Then I have used this simple script to probe the memory block by hand
# cat probe_memblock.sh
#!/bin/sh
BLOCK_NR=$1
# echo $((0x100000000+$BLOCK_NR*(128<<20))) > /sys/devices/system/memory/probe
# for i in $(seq 10); do sh probe_memblock.sh $i; done
# grep . /sys/devices/system/memory/memory3?/valid_zones 2>/dev/null
/sys/devices/system/memory/memory33/valid_zones:Normal Movable
/sys/devices/system/memory/memory34/valid_zones:Normal Movable
/sys/devices/system/memory/memory35/valid_zones:Normal Movable
/sys/devices/system/memory/memory36/valid_zones:Normal Movable
/sys/devices/system/memory/memory37/valid_zones:Normal Movable
/sys/devices/system/memory/memory38/valid_zones:Normal Movable
/sys/devices/system/memory/memory39/valid_zones:Normal Movable
The main difference to the original implementation is that all new
memblocks can be both online_kernel and online_movable initially because
there is no clash obviously. For the comparison the original
implementation would have
/sys/devices/system/memory/memory33/valid_zones:Normal
/sys/devices/system/memory/memory34/valid_zones:Normal
/sys/devices/system/memory/memory35/valid_zones:Normal
/sys/devices/system/memory/memory36/valid_zones:Normal
/sys/devices/system/memory/memory37/valid_zones:Normal
/sys/devices/system/memory/memory38/valid_zones:Normal
/sys/devices/system/memory/memory39/valid_zones:Normal Movable
Now
# echo online_movable > /sys/devices/system/memory/memory34/state
# grep . /sys/devices/system/memory/memory3?/valid_zones 2>/dev/null
/sys/devices/system/memory/memory33/valid_zones:Normal Movable
/sys/devices/system/memory/memory34/valid_zones:Movable
/sys/devices/system/memory/memory35/valid_zones:Movable
/sys/devices/system/memory/memory36/valid_zones:Movable
/sys/devices/system/memory/memory37/valid_zones:Movable
/sys/devices/system/memory/memory38/valid_zones:Movable
/sys/devices/system/memory/memory39/valid_zones:Movable
Block 33 can still be online both kernel and movable while all
the remaining can be only movable.
/proc/zonelist says
Node 0, zone Normal
pages free 0
min 0
low 0
high 0
spanned 0
present 0
--
Node 0, zone Movable
pages free 32753
min 85
low 117
high 149
spanned 32768
present 32768
A new memblock at a lower address will result in a new memblock (32)
which will still allow both Normal and Movable.
# sh probe_memblock.sh 0
# grep . /sys/devices/system/memory/memory3[2-5]/valid_zones 2>/dev/null
/sys/devices/system/memory/memory32/valid_zones:Normal Movable
/sys/devices/system/memory/memory33/valid_zones:Normal Movable
/sys/devices/system/memory/memory34/valid_zones:Movable
/sys/devices/system/memory/memory35/valid_zones:Movable
and online_kernel will convert it to the zone normal properly
while 33 can be still onlined both ways.
# echo online_kernel > /sys/devices/system/memory/memory32/state
# grep . /sys/devices/system/memory/memory3[2-5]/valid_zones 2>/dev/null
/sys/devices/system/memory/memory32/valid_zones:Normal
/sys/devices/system/memory/memory33/valid_zones:Normal Movable
/sys/devices/system/memory/memory34/valid_zones:Movable
/sys/devices/system/memory/memory35/valid_zones:Movable
/proc/zoneinfo will now tell
Node 0, zone Normal
pages free 65441
min 165
low 230
high 295
spanned 65536
present 65536
--
Node 0, zone Movable
pages free 32740
min 82
low 114
high 146
spanned 32768
present 32768
so both zones have one memblock spanned and present.
Onlining 39 should associate this block to the movable zone
# echo online > /sys/devices/system/memory/memory39/state
/proc/zoneinfo will now tell
Node 0, zone Normal
pages free 32765
min 80
low 112
high 144
spanned 32768
present 32768
--
Node 0, zone Movable
pages free 65501
min 160
low 225
high 290
spanned 196608
present 65536
so we will have a movable zone which spans 6 memblocks, 2 present and 4
representing a hole.
Offlining both movable blocks will lead to the zone with no present
pages which is the expected behavior I believe.
# echo offline > /sys/devices/system/memory/memory39/state
# echo offline > /sys/devices/system/memory/memory34/state
# grep -A6 "Movable\|Normal" /proc/zoneinfo
Node 0, zone Normal
pages free 32735
min 90
low 122
high 154
spanned 32768
present 32768
--
Node 0, zone Movable
pages free 0
min 0
low 0
high 0
spanned 196608
present 0
As a bonus we will get a nice cleanup in the memory hotplug codebase.
This patch (of 16):
init_currently_empty_zone doesn't have any error to return yet it is
still an int and callers try to be defensive and try to handle potential
error. Remove this nonsense and simplify all callers.
This patch shouldn't have any visible effect
Link: http://lkml.kernel.org/r/20170515085827.16474-2-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Daniel Kiper <daniel.kiper@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Reza Arbab <arbab@linux.vnet.ibm.com>
Cc: Tobias Regnery <tobias.regnery@gmail.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If there is no compound map for a THP (Transparent Huge Page), it is
possible that the map count of some sub-pages of the THP is 0. So it is
better to split the THP before swapping out. In this way, the sub-pages
not mapped will be freed, and we can avoid the unnecessary swap out
operations for these sub-pages.
Link: http://lkml.kernel.org/r/20170515112522.32457-6-ying.huang@intel.com
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Ebru Akagunduz <ebru.akagunduz@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Shaohua Li <shli@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To swap out THP (Transparent Huage Page), before splitting the THP, the
swap cluster will be allocated and the THP will be added into the swap
cache. But it is possible that the THP cannot be split, so that we must
delete the THP from the swap cache and free the swap cluster. To avoid
that, in this patch, whether the THP can be split is checked firstly.
The check can only be done racy, but it is good enough for most cases.
With the patch, the swap out throughput improves 3.6% (from about
4.16GB/s to about 4.31GB/s) in the vm-scalability swap-w-seq test case
with 8 processes. The test is done on a Xeon E5 v3 system. The swap
device used is a RAM simulated PMEM (persistent memory) device. To test
the sequential swapping out, the test case creates 8 processes, which
sequentially allocate and write to the anonymous pages until the RAM and
part of the swap device is used up.
Link: http://lkml.kernel.org/r/20170515112522.32457-5-ying.huang@intel.com
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> [for can_split_huge_page()]
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Ebru Akagunduz <ebru.akagunduz@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Shaohua Li <shli@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The add_to_swap aims to allocate swap_space(ie, swap slot and swapcache)
so if it fails due to lack of space in case of THP or something(hdd swap
but tries THP swapout) *caller* rather than add_to_swap itself should
split the THP page and retry it with base page which is more natural.
Link: http://lkml.kernel.org/r/20170515112522.32457-4-ying.huang@intel.com
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Ebru Akagunduz <ebru.akagunduz@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Shaohua Li <shli@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now, get_swap_page takes struct page and allocates swap space according
to page size(ie, normal or THP) so it would be more cleaner to introduce
put_swap_page which is a counter function of get_swap_page. Then, it
calls right swap slot free function depending on page's size.
[ying.huang@intel.com: minor cleanup and fix]
Link: http://lkml.kernel.org/r/20170515112522.32457-3-ying.huang@intel.com
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Ebru Akagunduz <ebru.akagunduz@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Shaohua Li <shli@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "THP swap: Delay splitting THP during swapping out", v11.
This patchset is to optimize the performance of Transparent Huge Page
(THP) swap.
Recently, the performance of the storage devices improved so fast that
we cannot saturate the disk bandwidth with single logical CPU when do
page swap out even on a high-end server machine. Because the
performance of the storage device improved faster than that of single
logical CPU. And it seems that the trend will not change in the near
future. On the other hand, the THP becomes more and more popular
because of increased memory size. So it becomes necessary to optimize
THP swap performance.
The advantages of the THP swap support include:
- Batch the swap operations for the THP to reduce lock
acquiring/releasing, including allocating/freeing the swap space,
adding/deleting to/from the swap cache, and writing/reading the swap
space, etc. This will help improve the performance of the THP swap.
- The THP swap space read/write will be 2M sequential IO. It is
particularly helpful for the swap read, which are usually 4k random
IO. This will improve the performance of the THP swap too.
- It will help the memory fragmentation, especially when the THP is
heavily used by the applications. The 2M continuous pages will be
free up after THP swapping out.
- It will improve the THP utilization on the system with the swap
turned on. Because the speed for khugepaged to collapse the normal
pages into the THP is quite slow. After the THP is split during the
swapping out, it will take quite long time for the normal pages to
collapse back into the THP after being swapped in. The high THP
utilization helps the efficiency of the page based memory management
too.
There are some concerns regarding THP swap in, mainly because possible
enlarged read/write IO size (for swap in/out) may put more overhead on
the storage device. To deal with that, the THP swap in should be turned
on only when necessary. For example, it can be selected via
"always/never/madvise" logic, to be turned on globally, turned off
globally, or turned on only for VMA with MADV_HUGEPAGE, etc.
This patchset is the first step for the THP swap support. The plan is
to delay splitting THP step by step, finally avoid splitting THP during
the THP swapping out and swap out/in the THP as a whole.
As the first step, in this patchset, the splitting huge page is delayed
from almost the first step of swapping out to after allocating the swap
space for the THP and adding the THP into the swap cache. This will
reduce lock acquiring/releasing for the locks used for the swap cache
management.
With the patchset, the swap out throughput improves 15.5% (from about
3.73GB/s to about 4.31GB/s) in the vm-scalability swap-w-seq test case
with 8 processes. The test is done on a Xeon E5 v3 system. The swap
device used is a RAM simulated PMEM (persistent memory) device. To test
the sequential swapping out, the test case creates 8 processes, which
sequentially allocate and write to the anonymous pages until the RAM and
part of the swap device is used up.
This patch (of 5):
In this patch, splitting huge page is delayed from almost the first step
of swapping out to after allocating the swap space for the THP
(Transparent Huge Page) and adding the THP into the swap cache. This
will batch the corresponding operation, thus improve THP swap out
throughput.
This is the first step for the THP swap optimization. The plan is to
delay splitting the THP step by step and avoid splitting the THP
finally.
In this patch, one swap cluster is used to hold the contents of each THP
swapped out. So, the size of the swap cluster is changed to that of the
THP (Transparent Huge Page) on x86_64 architecture (512). For other
architectures which want such THP swap optimization,
ARCH_USES_THP_SWAP_CLUSTER needs to be selected in the Kconfig file for
the architecture. In effect, this will enlarge swap cluster size by 2
times on x86_64. Which may make it harder to find a free cluster when
the swap space becomes fragmented. So that, this may reduce the
continuous swap space allocation and sequential write in theory. The
performance test in 0day shows no regressions caused by this.
In the future of THP swap optimization, some information of the swapped
out THP (such as compound map count) will be recorded in the
swap_cluster_info data structure.
The mem cgroup swap accounting functions are enhanced to support charge
or uncharge a swap cluster backing a THP as a whole.
The swap cluster allocate/free functions are added to allocate/free a
swap cluster for a THP. A fair simple algorithm is used for swap
cluster allocation, that is, only the first swap device in priority list
will be tried to allocate the swap cluster. The function will fail if
the trying is not successful, and the caller will fallback to allocate a
single swap slot instead. This works good enough for normal cases. If
the difference of the number of the free swap clusters among multiple
swap devices is significant, it is possible that some THPs are split
earlier than necessary. For example, this could be caused by big size
difference among multiple swap devices.
The swap cache functions is enhanced to support add/delete THP to/from
the swap cache as a set of (HPAGE_PMD_NR) sub-pages. This may be
enhanced in the future with multi-order radix tree. But because we will
split the THP soon during swapping out, that optimization doesn't make
much sense for this first step.
The THP splitting functions are enhanced to support to split THP in swap
cache during swapping out. The page lock will be held during allocating
the swap cluster, adding the THP into the swap cache and splitting the
THP. So in the code path other than swapping out, if the THP need to be
split, the PageSwapCache(THP) will be always false.
The swap cluster is only available for SSD, so the THP swap optimization
in this patchset has no effect for HDD.
[ying.huang@intel.com: fix two issues in THP optimize patch]
Link: http://lkml.kernel.org/r/87k25ed8zo.fsf@yhuang-dev.intel.com
[hannes@cmpxchg.org: extensive cleanups and simplifications, reduce code size]
Link: http://lkml.kernel.org/r/20170515112522.32457-2-ying.huang@intel.com
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Suggested-by: Andrew Morton <akpm@linux-foundation.org> [for config option]
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> [for changes in huge_memory.c and huge_mm.h]
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Ebru Akagunduz <ebru.akagunduz@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Shaohua Li <shli@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Standardize the file operation variable names related to all four memory
management /proc interface files. Also change all the symbol
permissions (S_IRUGO) into octal permissions (0444) as it got complaints
from checkpatch.pl. This does not create any functional change to the
interface.
Link: http://lkml.kernel.org/r/20170427030632.8588-1-khandual@linux.vnet.ibm.com
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Regardless of whether it is same page or not, it's surely write and
stored to zram so we should increase pages_stored stat. Otherwise, user
can see zero value via mm_stats although he writes a lot of pages to
zram.
Link: http://lkml.kernel.org/r/1494834068-27004-1-git-send-email-minchan@kernel.org
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a candidate stable_node_dup has been found and it can accept further
merges it can be refiled to the head of the list to speedup next
searches without altering which dup is found and how the dups accumulate
in the chain.
We already refiled it back to the head in the prune_stale_stable_nodes
case, but we didn't refile it if not pruning (which is more common).
And we also refiled it when it was already at the head which is
unnecessary (in the prune_stale_stable_nodes case, nr > 1 means there's
more than one dup in the chain, it doesn't mean it's not already at the
head of the chain).
The stable_node_chain list is single threaded and there's no SMP locking
contention so it should be faster to refile it to the head of the list
also if prune_stale_stable_nodes is false.
Profiling shows the refile happens 1.9% of the time when a dup is found
with a max_page_sharing limit setting of 3 (with max_page_sharing of 2
the refile never happens of course as there's never space for one more
merge) which is reasonably low. At higher max_page_sharing values it
should be much less frequent.
This is just an optimization.
Link: http://lkml.kernel.org/r/20170518173721.22316-4-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Evgheni Dereveanchin <ederevea@redhat.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Petr Holasek <pholasek@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Gavin Guo <gavin.guo@canonical.com>
Cc: Jay Vosburgh <jay.vosburgh@canonical.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some static checker complains if chain/chain_prune returns a potentially
stale pointer.
There are two output parameters to chain/chain_prune, one is tree_page
the other is stable_node_dup. Like in get_ksm_page the caller has to
check tree_page is NULL before touching the stable_node. Similarly in
chain/chain_prune the caller has to check tree_page before touching the
stable_node_dup returned or the original stable_node passed as
parameter.
Because the tree_page is never returned as a stale pointer, it may be
more intuitive to return tree_page and to pass stable_node_dup for
reference instead of the reverse.
This patch purely swaps the two output parameters of chain/chain_prune
as a cleanup for the static checker and to mimic the get_ksm_page
behavior more closely. There's no change to the caller at all except
the swap, it's purely a cleanup and it is a noop from the caller point
of view.
Link: http://lkml.kernel.org/r/20170518173721.22316-3-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Evgheni Dereveanchin <ederevea@redhat.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Petr Holasek <pholasek@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Gavin Guo <gavin.guo@canonical.com>
Cc: Jay Vosburgh <jay.vosburgh@canonical.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "KSMscale cleanup/optimizations".
There are no fixes here it's just minor cleanups and optimizations.
1/3 removes makes the "fix" for the stale stable_node fall in the
standard case without introducing new cases. Setting stable_node to
NULL was marginally safer, but stale pointer is still wiped from the
caller, this looks cleaner.
2/3 should fix the false positive from Dan's static checker.
3/3 is a microoptimization to apply the the refile of future merge
candidate dups at the head of the chain in all cases and to skip it in
one case where we did it and but it was a noop (to avoid checking if
it was already at the head but now we've to check it anyway so it got
optimized away).
This patch (of 3):
When the stable_node chain is collapsed we can as well set the caller
stable_node to match the returned stable_node_dup in chain_prune().
This way the collapse case becomes indistinguishable from the regular
stable_node case and we can remove two branches from the KSM page
migration handling slow paths.
While it was all correct this looks cleaner (and faster) as the caller has
to deal with fewer special cases.
Link: http://lkml.kernel.org/r/20170518173721.22316-2-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Evgheni Dereveanchin <ederevea@redhat.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Petr Holasek <pholasek@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Gavin Guo <gavin.guo@canonical.com>
Cc: Jay Vosburgh <jay.vosburgh@canonical.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If merge_across_nodes was manually set to 0 (not the default value) by
the admin or a tuned profile on NUMA systems triggering cross-NODE page
migrations, a stable_node use after free could materialize.
If the chain is collapsed stable_node would point to the old chain that
was already freed. stable_node_dup would be the stable_node dup now
converted to a regular stable_node and indexed in the rbtree in
replacement of the freed stable_node chain (not anymore a dup).
This special case where the chain is collapsed in the NUMA replacement
path, is now detected by setting stable_node to NULL by the chain_prune
callee if it decides to collapse the chain. This tells the NUMA
replacement code that even if stable_node and stable_node_dup are
different, this is not a chain if stable_node is NULL, as the
stable_node_dup was converted to a regular stable_node and the chain was
collapsed.
It is generally safer for the callee to force the caller stable_node to
NULL the moment it become stale so any other mistake like this would
result in an instant Oops easier to debug than an use after free.
Otherwise the replace logic would act like if stable_node was a valid
chain, when in fact it was freed. Notably
stable_node_chain_add_dup(page_node, stable_node) would run on a stable
stable_node.
Andrey Ryabinin found the source of the use after free in chain_prune().
Link: http://lkml.kernel.org/r/20170512193805.8807-2-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reported-by: Evgheni Dereveanchin <ederevea@redhat.com>
Tested-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Petr Holasek <pholasek@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Gavin Guo <gavin.guo@canonical.com>
Cc: Jay Vosburgh <jay.vosburgh@canonical.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Without a max deduplication limit for each KSM page, the list of the
rmap_items associated to each stable_node can grow infinitely large.
During the rmap walk each entry can take up to ~10usec to process
because of IPIs for the TLB flushing (both for the primary MMU and the
secondary MMUs with the MMU notifier). With only 16GB of address space
shared in the same KSM page, that would amount to dozens of seconds of
kernel runtime.
A ~256 max deduplication factor will reduce the latencies of the rmap
walks on KSM pages to order of a few msec. Just doing the
cond_resched() during the rmap walks is not enough, the list size must
have a limit too, otherwise the caller could get blocked in (schedule
friendly) kernel computations for seconds, unexpectedly.
There's room for optimization to significantly reduce the IPI delivery
cost during the page_referenced(), but at least for page_migration in
the KSM case (used by hard NUMA bindings, compaction and NUMA balancing)
it may be inevitable to send lots of IPIs if each rmap_item->mm is
active on a different CPU and there are lots of CPUs. Even if we ignore
the IPI delivery cost, we've still to walk the whole KSM rmap list, so
we can't allow millions or billions (ulimited) number of entries in the
KSM stable_node rmap_item lists.
The limit is enforced efficiently by adding a second dimension to the
stable rbtree. So there are three types of stable_nodes: the regular
ones (identical as before, living in the first flat dimension of the
stable rbtree), the "chains" and the "dups".
Every "chain" and all "dups" linked into a "chain" enforce the invariant
that they represent the same write protected memory content, even if
each "dup" will be pointed by a different KSM page copy of that content.
This way the stable rbtree lookup computational complexity is unaffected
if compared to an unlimited max_sharing_limit. It is still enforced
that there cannot be KSM page content duplicates in the stable rbtree
itself.
Adding the second dimension to the stable rbtree only after the
max_page_sharing limit hits, provides for a zero memory footprint
increase on 64bit archs. The memory overhead of the per-KSM page
stable_tree and per virtual mapping rmap_item is unchanged. Only after
the max_page_sharing limit hits, we need to allocate a stable_tree
"chain" and rb_replace() the "regular" stable_node with the newly
allocated stable_node "chain". After that we simply add the "regular"
stable_node to the chain as a stable_node "dup" by linking hlist_dup in
the stable_node_chain->hlist. This way the "regular" (flat) stable_node
is converted to a stable_node "dup" living in the second dimension of
the stable rbtree.
During stable rbtree lookups the stable_node "chain" is identified as
stable_node->rmap_hlist_len == STABLE_NODE_CHAIN (aka
is_stable_node_chain()).
When dropping stable_nodes, the stable_node "dup" is identified as
stable_node->head == STABLE_NODE_DUP_HEAD (aka is_stable_node_dup()).
The STABLE_NODE_DUP_HEAD must be an unique valid pointer never used
elsewhere in any stable_node->head/node to avoid a clashes with the
stable_node->node.rb_parent_color pointer, and different from
&migrate_nodes. So the second field of &migrate_nodes is picked and
verified as always safe with a BUILD_BUG_ON in case the list_head
implementation changes in the future.
The STABLE_NODE_DUP is picked as a random negative value in
stable_node->rmap_hlist_len. rmap_hlist_len cannot become negative when
it's a "regular" stable_node or a stable_node "dup".
The stable_node_chain->nid is irrelevant. The stable_node_chain->kpfn
is aliased in a union with a time field used to rate limit the
stable_node_chain->hlist prunes.
The garbage collection of the stable_node_chain happens lazily during
stable rbtree lookups (as for all other kind of stable_nodes), or while
disabling KSM with "echo 2 >/sys/kernel/mm/ksm/run" while collecting the
entire stable rbtree.
While the "regular" stable_nodes and the stable_node "dups" must wait
for their underlying tree_page to be freed before they can be freed
themselves, the stable_node "chains" can be freed immediately if the
stable_node->hlist turns empty. This is because the "chains" are never
pointed by any page->mapping and they're effectively stable rbtree KSM
self contained metadata.
[akpm@linux-foundation.org: fix non-NUMA build]
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Tested-by: Petr Holasek <pholasek@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Evgheni Dereveanchin <ederevea@redhat.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Gavin Guo <gavin.guo@canonical.com>
Cc: Jay Vosburgh <jay.vosburgh@canonical.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When start_pfn equals end_pfn, __free_pages_memory() has no effect and
__free_memory_core() will finally return (end_pfn - start_pfn) = 0.
This patch returns 0 directly when start_pfn equals end_pfn.
Link: http://lkml.kernel.org/r/20170502131115.6650-1-richard.weiyang@gmail.com
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clang and its -Wunsequenced emits a warning
mm/vmscan.c:2961:25: error: unsequenced modification and access to 'gfp_mask' [-Wunsequenced]
.gfp_mask = (gfp_mask = current_gfp_context(gfp_mask)),
^
While it is not clear to me whether the initialization code violates the
specification (6.7.8 par 19 (ISO/IEC 9899) looks like it disagrees) the
code is quite confusing and worth cleaning up anyway. Fix this by
reusing sc.gfp_mask rather than the updated input gfp_mask parameter.
Link: http://lkml.kernel.org/r/20170510154030.10720-1-nick.desaulniers@gmail.com
Signed-off-by: Nick Desaulniers <nick.desaulniers@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The protection map is only modified by per-arch init code so it can be
protected from writes after the init code runs.
This change was extracted from PaX where it's part of KERNEXEC.
Link: http://lkml.kernel.org/r/20170510174441.26163-1-danielmicay@gmail.com
Signed-off-by: Daniel Micay <danielmicay@gmail.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a number of times that we loop over NR_MEM_SECTIONS, looking
for section_present() on each section. But, when we have very large
physical address spaces (large MAX_PHYSMEM_BITS), NR_MEM_SECTIONS
becomes very large, making the loops quite long.
With MAX_PHYSMEM_BITS=46 and a section size of 128MB, the current loops
are 512k iterations, which we barely notice on modern hardware. But,
raising MAX_PHYSMEM_BITS higher (like we will see on systems that
support 5-level paging) makes this 64x longer and we start to notice,
especially on slower systems like simulators. A 10-second delay for
512k iterations is annoying. But, a 640- second delay is crippling.
This does not help if we have extremely sparse physical address spaces,
but those are quite rare. We expect that most of the "slow" systems
where this matters will also be quite small and non-sparse.
To fix this, we track the highest section we've ever encountered. This
lets us know when we will *never* see another section_present(), and
lets us break out of the loops earlier.
Doing the whole for_each_present_section_nr() macro is probably
overkill, but it will ensure that any future loop iterations that we
grow are more likely to be correct.
Kirrill said "It shaved almost 40 seconds from boot time in qemu with
5-level paging enabled for me".
Link: http://lkml.kernel.org/r/20170504174434.C45A4735@viggo.jf.intel.com
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some hardened environments want to build kernels with slab_nomerge
already set (so that they do not depend on remembering to set the kernel
command line option). This is desired to reduce the risk of kernel heap
overflows being able to overwrite objects from merged caches and changes
the requirements for cache layout control, increasing the difficulty of
these attacks. By keeping caches unmerged, these kinds of exploits can
usually only damage objects in the same cache (though the risk to
metadata exploitation is unchanged).
Link: http://lkml.kernel.org/r/20170620230911.GA25238@beast
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Daniel Micay <danielmicay@gmail.com>
Cc: David Windsor <dave@nullcore.net>
Cc: Eric Biggers <ebiggers3@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Daniel Micay <danielmicay@gmail.com>
Cc: David Windsor <dave@nullcore.net>
Cc: Eric Biggers <ebiggers3@gmail.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20170616072918epcms5p4ff16c24ef8472b4c3b4371823cd87856@epcms5p4
Signed-off-by: Canjiang Lu <canjiang.lu@samsung.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kmem_cache->cpu_partial is just used when CONFIG_SLUB_CPU_PARTIAL is
set, so wrap it with config CONFIG_SLUB_CPU_PARTIAL will save some space
on 32bit arch.
This patch wraps kmem_cache->cpu_partial in config CONFIG_SLUB_CPU_PARTIAL
and wraps its sysfs too.
Link: http://lkml.kernel.org/r/20170502144533.10729-4-richard.weiyang@gmail.com
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cpu_slab's field partial is used when CONFIG_SLUB_CPU_PARTIAL is set,
which means we can save a pointer's space on each cpu for every slub
item.
This patch wraps cpu_slab->partial in CONFIG_SLUB_CPU_PARTIAL and wraps
its sysfs use too.
[akpm@linux-foundation.org: avoid strange 80-col tricks]
Link: http://lkml.kernel.org/r/20170502144533.10729-3-richard.weiyang@gmail.com
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "try to save some memory for kmem_cache in some cases", v2.
kmem_cache is a frequently used data in kernel. During the code
reading, I found maybe we could save some space in some cases.
1. On 64bit arch, type int will occupy a word if it doesn't sit well.
2. cpu_slab->partial is just used when CONFIG_SLUB_CPU_PARTIAL is set
3. cpu_partial is just used when CONFIG_SLUB_CPU_PARTIAL is set, while
just save some space on 32bit arch.
This patch (of 3):
On 64bit arch, struct is 8-bytes aligned, so int will occupy a word if
it doesn't sit well.
This patch pack red_left_pad with reserved to save 8 bytes for struct
kmem_cache on a 64bit arch.
Link: http://lkml.kernel.org/r/20170502144533.10729-2-richard.weiyang@gmail.com
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Each time a slab is deactivated, the page and freelist pointer should be
reset.
This patch just merges these two options into deactivate_slab().
Link: http://lkml.kernel.org/r/20170507031215.3130-2-richard.weiyang@gmail.com
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the code comes to this point, there are two cases:
1. cpu_slab is deactivated
2. cpu_slab is empty
In both cased, cpu_slab->freelist is NULL at this moment.
This patch removes the redundant assignment of cpu_slab->freelist.
Link: http://lkml.kernel.org/r/20170507031215.3130-1-richard.weiyang@gmail.com
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no real reason to duplicate kvmalloc* helpers so drop
alloc_fdmem and replace it with the appropriate library function.
Link: http://lkml.kernel.org/r/20170531155145.17111-2-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
4402 1088 38 5528 1598 fs/ocfs2/stackglue.o
File size After adding 'const':
text data bss dec hex filename
4442 1024 38 5504 1580 fs/ocfs2/stackglue.o
Link: http://lkml.kernel.org/r/cab4e59b4918db3ed2ec77073a4cb310c4429ef5.1498808026.git.arvind.yadav.cs@gmail.com
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <jiangqi903@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'sd->dbg_sock' is malloced in sc_common_open(), but not freed at the end
of sc_fop_release().
Link: http://lkml.kernel.org/r/594FB0A4.2050105@huawei.com
Signed-off-by: Jun Piao <piaojun@huawei.com>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Filesystems generally use SUPER_MAGIC values from magic.h instead of a
local definition.
Link: http://lkml.kernel.org/r/20170521154217.27917-1-fabf@skynet.be
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Reviewed-by: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <jiangqi903@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a static code checker warning:
fs/ocfs2/inode.c:179 ocfs2_iget() warn: passing zero to 'ERR_PTR'
Fixes: d56a8f32e4 ("ocfs2: check/fix inode block for online file check")
Link: http://lkml.kernel.org/r/1495516634-1952-1-git-send-email-ghe@suse.com
Signed-off-by: Gang He <ghe@suse.com>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Reviewed-by: Eric Ren <zren@suse.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This header always exists, so doesn't require an ifdef around its
inclusion. When CONFIG_ARCH_HAS_SET_MEMORY=y it includes the asm
header, otherwise it provides empty versions of the set_memory_xx()
routines.
Link: http://lkml.kernel.org/r/1498717781-29151-4-git-send-email-mpe@ellerman.id.au
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This header always exists, so doesn't require an ifdef around its
inclusion. When CONFIG_ARCH_HAS_SET_MEMORY=y it includes the asm
header, otherwise it provides empty versions of the set_memory_xx()
routines.
The usages of set_memory_xx() are still guarded by
CONFIG_STRICT_MODULE_RWX.
Link: http://lkml.kernel.org/r/1498717781-29151-3-git-send-email-mpe@ellerman.id.au
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Laura Abbott <labbott@redhat.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This header always exists, so doesn't require an ifdef around its
inclusion. When CONFIG_ARCH_HAS_SET_MEMORY=y it includes the asm
header, otherwise it provides empty versions of the set_memory_xx()
routines.
Link: http://lkml.kernel.org/r/1498717781-29151-2-git-send-email-mpe@ellerman.id.au
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Laura Abbott <labbott@redhat.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently code that wants to use set_memory_ro() etc, needs to include
asm/set_memory.h, which doesn't exist on all arches. Some code knows it
only builds on arches which have the header, other code guards the
inclusion with an #ifdef, neither is ideal.
So create linux/set_memory.h. This always exists, so users don't need
an #ifdef just to include the header.
When CONFIG_ARCH_HAS_SET_MEMORY=y it includes asm/set_memory.h,
otherwise it provides empty non-failing implementations.
Link: http://lkml.kernel.org/r/1498717781-29151-1-git-send-email-mpe@ellerman.id.au
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are some of the more spelling mistakes and typos that I've found
while fixing up spelling mistakes in kernel error message text over the
past several weeks.
Link: http://lkml.kernel.org/r/20170621142614.12529-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Joe Perches <joe@perches.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clarify help text that compression applies to ramfs as well as legacy ramdisk.
Link: http://lkml.kernel.org/r/f206a960-5a61-cf59-f27c-e9f34872063c@landley.net
Signed-off-by: Rob Landley <rob@landley.net>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Teach INITRAMFS_ROOT_UID and INITRAMFS_ROOT_GID that -1 means "current user".
Link: http://lkml.kernel.org/r/2df3a9fb-4378-fa16-679d-99e788926c05@landley.net
Signed-off-by: Rob Landley <rob@landley.net>
Cc: Michal Marek <mmarek@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a default ioremap function which was not provided in all
circumstances. (Only when CONFIG_PCI and CONFIG_TILEGX was set).
I have designs to use them in scatterlist.c where they'd likely never be
called with this architecture, but it is needed to compile. Thus, if
the function is ever hit it returns NULL.
Link: http://lkml.kernel.org/r/1495726904-27380-1-git-send-email-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Stephen Bates <sbates@raithlin.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The mn10300 arch uses a verbatim copy of the asm-generic version and
does not add any own implementations to the header, so use
asm-generic/fb.h instead of duplicating code.
Link: http://lkml.kernel.org/r/20170517083348.1815-1-tklauser@distanz.ch
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mn10300's asm/device.h is merely including asm-generic/device.h. Thus,
the arch specific header can be omitted and the generic header can be
used directly.
Link: http://lkml.kernel.org/r/20170517124857.26834-1-tklauser@distanz.ch
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko
Huang Ying
Minchan Kim
Anshuman Khandual
Andrea Arcangeli
Wei Yang
Nick Desaulniers
Daniel Micay
Dave Hansen
Kees Cook
Canjiang Lu
Arvind Yadav
piaojun
Fabian Frederick
Gang He
SF Markus Elfring
Michael Ellerman
Colin Ian King
Rob Landley
Logan Gunthorpe
Tobias Klauser