Now that we only ack irq 0 the code can be simplified a lot.
Also switch from read / modify / write to a simple write clear:
1) This is what the android code does (it has a hack for acking irq 0
in its unmask code doing this)
2) read / modify / write simply does not make sense for an irq status
register like this, if the other bits are writeable (and the data sheet says
they are not) they should be write 1 to clear, since otherwise a read /
modify / write can race with a device raising an interrupt and then clear
the pending bit unintentionally
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-sunxi@googlegroups.com
Link: http://lkml.kernel.org/r/1394895894-8891-3-git-send-email-hdegoede@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since the sun4i irq chip does not require any action and clears the interrupt
when the level goes back to inactive, we don't need to mask / unmask for
non oneshot IRQs, to achieve this we make sun4i_irq_ack a nop for all irqs
except irq 0 and use handle_fasteoi_irq for all interrupts.
Now there might be a case when the device reactivates the interrupt
before the RETI. But that does not matter as we run the primary
interrupt handlers with interrupts disabled.
This also allows us to get rid of needing to use 2 irq_chip structs, this
means that the IRQCHIP_EOI_THREADED | IRQCHIP_EOI_IF_HANDLED will now influence
all interrupts rather then just irq 0, but that does not matter as the eoi
is now a nop anyways for all interrupts but irq 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-sunxi@googlegroups.com
Link: http://lkml.kernel.org/r/1394895894-8891-2-git-send-email-hdegoede@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
All IRQs except for IRQ 0 seem to not need acking, so drop acking for them.
The ENMI needs to have the ack done *after* clearing the interrupt source,
otherwise we will get a spurious interrupt for each real interrupt.
So use the new IRQCHIP_EOI_THREADED flag for this in combination with
handle_fasteoi_irq. This uses a separate irq_chip struct for IRQ 0,
since we only want this behavior for IRQ 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-sunxi@googlegroups.com
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: http://lkml.kernel.org/r/1394733834-26839-5-git-send-email-hdegoede@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
SUN4I_IRQ_VECTOR_REG containing 0 can mean one of 3 things:
1) no more irqs pending
2) irq 0 pending
3) spurious irq
So if we immediately get a reading of 0, check the irq-pending reg
to differentiate between 2 and 3. We only do this once to avoid
the extra check in the common case of 1) hapening after having
read the vector-reg once.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-sunxi@googlegroups.com
Link: http://lkml.kernel.org/r/1394733834-26839-3-git-send-email-hdegoede@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Change the compatibles
to match the other pattern in the irq controller driver for consistency.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Merge the request/release callbacks which are in a separate branch for
consumption by the gpio folks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The "irqchip.h" include here is not needed as the only thing in
irqchip.h is IRQCHIP_DECLARE which this file doesn't use. Drop
it.
Reported-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Link: http://lkml.kernel.org/r/531F7765.40207@codeaurora.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LTO patches add __visible to the asmlinkage define, causing
compilation warnings like:
drivers/irqchip/irq-gic.c:283:1: warning: 'externally_visible'
attribute have effect only on public objects [-Wattributes]
Drop asmlinkage here to avoid such warnings.
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: khilman@linaro.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Josh Cartwright <joshc@codeaurora.org>
Cc: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/1393980030-17770-1-git-send-email-sboyd@codeaurora.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
drivers/irqchip/irq-gic.c:53:23: warning: duplicate [noderef]
drivers/irqchip/irq-gic.c:651:6: warning: symbol 'gic_raise_softirq' was not declared. Should it be static?
drivers/irqchip/irq-gic.c:872:29: warning: symbol 'gic_irq_domain_ops' was not declared. Should it be static?
drivers/irqchip/irq-gic.c:977:12: warning: symbol 'gic_of_init' was not declared. Should it be static?
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1393981321-25721-1-git-send-email-sboyd@codeaurora.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The user space interface does not filter out offline cpus. It merily
verifies that the mask contains at least one online cpu. So the
selector in the irq chip implementation needs to make sure to pick
only an online cpu because otherwise:
Offline Core 1
Set affinity to 0xe
Selector will pick first set bit, i.e. core 1
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Chris Zankel <chris@zankel.net>
Cc: xtensa <linux-xtensa@linux-xtensa.org>
This reverts commit 40b367d95f.
Russell King has raised the idea of creating a proper PMU driver for
this SoC that would incorporate the functionality currently in this
driver. It would also cover the use case for the graphics subsystem on
this SoC.
To prevent having to maintain the devicetree ABI for this limited
interrupt-handler driver, we revert the driver before it hits a mainline
tagged release (eg v3.15).
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/1393911160-7688-1-git-send-email-jason@lakedaemon.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix irq_set_affinity callbacks in the Meta IRQ chip drivers to AND
cpu_online_mask into the cpumask when picking a CPU to vector the
interrupt to.
As Thomas pointed out, the /proc/irq/$N/smp_affinity interface doesn't
filter out offline CPUs, so without this patch if you offline CPU0 and
set an IRQ affinity to 0x3 it vectors the interrupt onto CPU0 even
though it is offline.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-metag@vger.kernel.org
Cc: stable@vger.kernel.org
The new Armada 375 and Armada 38x Marvell SoCs are based on Cortex-A9
CPU cores and use the ARM GIC as their main interrupt controller.
However, for various purposes (wake-up from suspend, MSI interrupts),
they have kept a separate MPIC interrupt controller, acting as a slave
to the GIC. This MPIC was already used as the primary controller on
previous Marvell SoCs, so this commit extends the existing driver to
allow the MPIC to be used as a GIC slave.
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Introduce a helper function to handle the MSI interrupts. This makes
the code more readable. In addition, this will allow to introduce a
chained IRQ handler mechanism, which is needed in situations where the
MPIC is used as a slave to another interrupt controller.
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
- orion:
- fixes for clearing bridge cause register, and clearing stale interrupts
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=r7Cd
-----END PGP SIGNATURE-----
Merge tag 'irqchip-mvebu-fixes-3.14' of git://git.infradead.org/linux-mvebu into irq/urgent
irqchip mvebu fixes for v3.14
- orion:
- fixes for clearing bridge cause register, and clearing stale interrupts
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Enabling SPARSE_IRQ shows up a bug in the irq-orion bridge interrupt
handler. The bridge interrupt is implemented using a single generic
chip. Thus the parameter passed to irq_get_domain_generic_chip()
should always be zero.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Fixes: 9dbd90f17e ("irqchip: Add support for Marvell Orion SoCs")
Cc: <stable@vger.kernel.org> # v3.11+
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Bridge IRQ_CAUSE bits are asserted regardless of the corresponding bit in
IRQ_MASK register. To avoid interrupt events on stale irqs, we have to clear
them before unmask. This installs an .irq_startup callback to ensure stale
irqs are cleared before initial unmask.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: <stable@vger.kernel.org>: f56c0738b5c2: "irqchip: orion: clear bridge cause register on init"
Cc: <stable@vger.kernel.org>: 38bd80b84fca: "irqchip: orion: use handle_edge_irq on bridge irqs"
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Bridge irqs are edge-triggered, i.e. they get asserted on low-to-high
transitions and not on the level of the downstream interrupt line.
This replaces handle_level_irq by the more appropriate handle_edge_irq.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: <stable@vger.kernel.org>: f56c0738b5c2: "irqchip: orion: clear bridge cause register on init"
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
It is good practice to mask and clear pending irqs on init. We already
mask all irqs, so also clear the bridge irq cause register.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull irq updates from Thomas Gleixner:
"This lot provides:
* Bugfixes for armada irq controller
* Updates to renesas irq chip
* Support for the TI-NSPIRE irq controller
Not strictly a bug fix only pull request, but important updates for
some of the arm Socs which I completely forgot to send last week.
Seems like my obliviousness is getting worse, I just can't remember
when it started"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Add support for TI-NSPIRE irqchip
irqchip: renesas-irqc: Enable mask on suspend
irqchip: renesas-irqc: Use lazy disable
irqchip: armada-370-xp: fix MSI race condition
irqchip: armada-370-xp: fix IPI race condition
- allow building and booting DT and non-DT plat-orion SoCs
- catch proper return value for kirkwood_pm_init()
- properly check return of of_iomap to solve boot hangs (mirabox, others)
- remove a compile warning on Armada 370 with non-SMP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=mxq4
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-3.13-2' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for v3.13 (incremental #2)
- allow building and booting DT and non-DT plat-orion SoCs
- catch proper return value for kirkwood_pm_init()
- properly check return of of_iomap to solve boot hangs (mirabox, others)
- remove a compile warning on Armada 370 with non-SMP.
* tag 'mvebu-fixes-3.13-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP)
ARM: mvebu: Fix kernel hang in mvebu_soc_id_init() when of_iomap failed
ARM: kirkwood: kirkwood_pm_init() should return void
ARM: orion: provide C-style interrupt handler for MULTI_IRQ_HANDLER
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJS4dWNAAoJEI9vqH3mFV2sargP/RCdVvdJm3TxYcNYoKAw6kTs
wn1AWQ1vnu77YIoG2YamWytakahvB5v4Elm5UbHc49eCIFb/+wJpvxLNKbAtY0EP
bRllFETalWnPnZO0R0tTvEikpDfzM7/OGYCjuOmTeyata6/KOxVsusTjvar28NPA
gVp9BwHKZyk5NORkvW3RBRbfga9slUXqbg4rPhD3gFxLpe8aGuO6T6HazBfRadQM
pI0zq2VE59LSEyuZrreHiq5EYvmp+eBFR8bJhQp1lnpKc4lMJm5JKYPY+jlPPtu0
bPYLexjb42Gz2KbDtqLqTnd6GEPj50RS15tr9BTX9n3uCd0sIBO46K5FXVy+ALxr
DXbyU6R1miZ01Il0A2IuC2j1cVdXb7nSytP35lLRQ9WCXua4HwQO0LL9KPAf9N0X
WKlNPEkOr9XR9lO/1JcYVZgsygF/hHGgImf5AEfTVdtWpAj3bhMBhqFuKo0/h6vr
7PwQCTaiL2Hks+d8YS2VyrQy3DMg48MbYmfdriJQFKKzhdyHEhvlnawP5uoIVfAC
s43cvj6EsbUdRULf5qKDupQFJpM15qpmYiLizHFIfUTiTQGI0WMaA76rZMqZ2AsQ
z0q2edzUV8nBQFdR74eKKPF1QJyXihiaXzug+SZqPdvXKfjPrF+5eZ7/EvuaEBZy
qS7PIt5nkTeZ4stP/SWV
=JT1d
-----END PGP SIGNATURE-----
Merge tag 'xtensa-next-20140123' of git://github.com/czankel/xtensa-linux
Pull Xtensa patches from Chris Zankel:
"The major changes are adding support for SMP for Xtensa, fixing and
cleaning up the ISS (simulator) network driver, and better support for
device trees"
* tag 'xtensa-next-20140123' of git://github.com/czankel/xtensa-linux: (40 commits)
xtensa: implement ndelay
xtensa: clean up udelay
xtensa: enable HAVE_PERF_EVENTS
xtensa: remap io area defined in device tree
xtensa: support default device tree buses
xtensa: initialize device tree clock sources
xtensa: xtfpga: fix definitions of platform devices
xtensa: standardize devicetree cpu compatible strings
xtensa: avoid duplicate of IO range definitions
xtensa: fix ATOMCTL register documentation
xtensa: Enable irqs after cpu is set online
xtensa: ISS: raise network polling rate to 10 times/sec
xtensa: remove unused XTENSA_ISS_NETWORK Kconfig parameter
xtensa: ISS: avoid simple_strtoul usage
xtensa: Switch to sched_clock_register()
xtensa: implement CPU hotplug
xtensa: add SMP support
xtensa: add MX irqchip
xtensa: clear timer IRQ unconditionally in its handler
xtensa: clean up do_interrupt/do_IRQ
...
Updates of SoC-near drivers and other driver updates that makes more sense to
take through our tree.
The largest part of this is a conversion of device registration for some
renesas shmobile/sh devices over to use resources. This has required
coordination with the corresponding arch/sh changes, and we've agreed
to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure firmware,
which is what is used on many of the commercial Nvidia Tegra products
that are in the market, including the Nvidia Shield. The code is local
to arch/arm at this time since it's uncertain whether it will be shared
with arm64 longer-term, if needed we will refactor later.
A couple of new RTC drivers used on ARM boards, merged through our tree
on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JJlw
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree.
The largest part of this is a conversion of device registration for
some renesas shmobile/sh devices over to use resources. This has
required coordination with the corresponding arch/sh changes, and
we've agreed to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure
firmware, which is what is used on many of the commercial Nvidia Tegra
products that are in the market, including the Nvidia Shield. The
code is local to arch/arm at this time since it's uncertain whether it
will be shared with arm64 longer-term, if needed we will refactor
later.
A couple of new RTC drivers used on ARM boards, merged through our
tree on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
watchdog: davinci: rename platform driver to davinci-wdt
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
...
New core SoC-specific changes.
New platforms:
* Introduction of a vendor, Hisilicon, and one of their SoCs with some
random numerical product name.
* Introduction of EFM32, embedded platform from Silicon Labs (ARMv7m, i.e. !MMU).
* Marvell Berlin series of SoCs, which include the one in Chromecast.
* MOXA platform support, ARM9-based platform used mostly in industrial products
* Support for Freescale's i.MX50 SoC.
Other work:
* Renesas work for new platforms and drivers, and conversion over to
more multiplatform-friendly device registration schemes.
* SMP support for Allwinner sunxi platforms.
* ... plus a bunch of other stuff across various platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pgLW
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New core SoC-specific changes.
New platforms:
* Introduction of a vendor, Hisilicon, and one of their SoCs with
some random numerical product name.
* Introduction of EFM32, embedded platform from Silicon Labs (ARMv7m,
i.e. !MMU).
* Marvell Berlin series of SoCs, which include the one in Chromecast.
* MOXA platform support, ARM9-based platform used mostly in
industrial products
* Support for Freescale's i.MX50 SoC.
Other work:
* Renesas work for new platforms and drivers, and conversion over to
more multiplatform-friendly device registration schemes.
* SMP support for Allwinner sunxi platforms.
* ... plus a bunch of other stuff across various platforms"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (201 commits)
ARM: tegra: fix tegra_powergate_sequence_power_up() inline
ARM: msm_defconfig: Update for multi-platform
ARM: msm: Move MSM's DT based hardware to multi-platform support
ARM: msm: Only build timer.c if required
ARM: msm: Only build clock.c on proc_comm based platforms
ARM: ux500: Enable system suspend with WFI support
ARM: ux500: turn on PRINTK_TIME in u8500_defconfig
ARM: shmobile: r8a7790: Fix I2C controller names
ARM: msm: Simplify ARCH_MSM_DT config
ARM: msm: Add support for MSM8974 SoC
ARM: sunxi: select ARM_PSCI
MAINTAINERS: Update Allwinner sunXi maintainer files
ARM: sunxi: Select RESET_CONTROLLER
ARM: imx: improve the comment of CCM lpm SW workaround
ARM: imx: improve status check of clock gate
ARM: imx: add necessary interface for pfd
ARM: imx_v6_v7_defconfig: Select CONFIG_REGULATOR_PFUZE100
ARM: imx_v6_v7_defconfig: Select MX35 and MX50 device tree support
ARM: imx: Add cpu frequency scaling support
ARM i.MX35: Add devicetree support.
...
This patch adds support for the interrupt controllers found in some
TI-Nspire models.
FIQ support was taken out to simplify the driver code and may be added
in later. Since Linux on this platform doesn't really use FIQs, this
wasn't really that important in the first place.
[ tglx: Made zevio_handle_irq static and reordered __init functions ]
Signed-off-by: Daniel Tang <dt.tangr@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Link: http://lkml.kernel.org/r/1386223937-12189-1-git-send-email-dt.tangr@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The following appears during compilation for an Armada 370 target
because 'irq_controller_lock' is used only when CONFIG_SMP is
enabled:
drivers/irqchip/irq-armada-370-xp.c:62:8: warning: 'irq_controller_lock' defined but not used [-Wunused-variable]
Fix that warning by moving declaration of 'irq_controller_lock'
inside existing #ifdef.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
MX is an interrupt distributor used in some SMP-capable xtensa
configurations.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Extract xtensa built-in interrupt controller implementation from
xtensa/kernel/irq.c and move it to other irqchips, providing way to
instantiate it from the device tree.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
SiRF internal interrupts are using level trigger. we need to tell the irq
core this information. otherwise, we might get some problems as below
1. disable_irq(n)
here irq core will mark the disabled flag but still keep the irq enabled
due to involved lazy-disable
2. doing someting after disable_irq(n)
in step 2, if one interrupt n comes, irq core will mark it as pending and
mask the HW interrupt really. we name the coming interrupt as "X".
3. enable_irq(n)
this will unmask the interrupt, so the level-trigger HW interrupt will come
again, irq_handler will enter as "E1". after that, irq core will also check
whether irq n is pending, if yes, and pending interrupt is not level-trigger,
irq core will execute the pending irq_handler.
so if we don't set the IRQ_LEVEL flag here, irq core will execute pending
X again as "E2", but actually the pending interrupt has been handled by "E1".
that makes a level-trigger HW interrupt is executed twice.
here we fix the issue to avoid redundant interrupt overload.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Huayi Li <Huayi.Li@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Use PATCH_PHYS_TO_VIRT and AUTO_ZRELADDR.
- Support cascaded interrupts on the SIC.
- Complete clock implementation for the IM-PD1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cCZc
-----END PGP SIGNATURE-----
Merge tag 'integrator-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/drivers
From Linus Walleij:
Some Integrator patches that matured for v3.14:
- Use PATCH_PHYS_TO_VIRT and AUTO_ZRELADDR.
- Support cascaded interrupts on the SIC.
- Complete clock implementation for the IM-PD1.
* tag 'integrator-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
ARM: integrator: Default enable ARM_PATCH_PHYS_VIRT, AUTO_ZRELADDR
Signed-off-by: Olof Johansson <olof@lixom.net>
The Versatile FPGA interrupt controller supports cascading interrupts,
i.e. that its output is connected to the input of another interrupt
controller. This makes it possible to pass a parent interrupt from
the device tree and print it in the boot log if applicable.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---------------------------
This pull request contains updates
to DaVinci GPIO driver and the
resultant platform code changes. The
updates include DT-conversion and
changes to make the driver cross-platform
ready.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=DxLt
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.14/gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers
From Sekhar Nori:
DaVinci GPIO driver updates
---------------------------
This pull request contains updates to DaVinci GPIO driver and the
resultant platform code changes. The updates include DT-conversion and
changes to make the driver cross-platform ready.
* tag 'davinci-for-v3.14/gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
Signed-off-by: Olof Johansson <olof@lixom.net>
Value 0 of the sense selection field of CONFIG_n register means "disable event
detection" and serves in irqc_sense[] for marking the invalid values of the IRQ
type (by just omitting initializers). There is no need for INTC_IRQ_SENSE_VALID
and hence INTC_IRQ_SENSE() as all field values matching to the valid IRQ types
are non-zero anyway.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* r8a7790 (R-Car H1) SoC
- Correct GPIO resources in DT.
This problem has been present since GPIOs were added to the r8a7790 SoC
by f98e10c88a ("ARM: shmobile: r8a7790: Add GPIO controller
devices to device tree") in v3.12-rc1.
* irqchip renesas-intc-irqpin
- Correct register bitfield shift calculation
This bug has been present since the renesas-intc-irqpin driver was
introduced by 443580486e ("irqchip: Renesas INTC External IRQ pin
driver") in v3.10-rc1
* Lager board
- Do not build the phy fixup unless CONFIG_PHYLIB is enabled
This problem was introduced by 48c8b96f21
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=Vbzt
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Renesas ARM based SoC fixes for v3.13
* r8a7790 (R-Car H1) SoC
- Correct GPIO resources in DT.
This problem has been present since GPIOs were added to the r8a7790 SoC
by f98e10c88a ("ARM: shmobile: r8a7790: Add GPIO controller
devices to device tree") in v3.12-rc1.
* irqchip renesas-intc-irqpin
- Correct register bitfield shift calculation
This bug has been present since the renesas-intc-irqpin driver was
introduced by 443580486e ("irqchip: Renesas INTC External IRQ pin
driver") in v3.10-rc1
* Lager board
- Do not build the phy fixup unless CONFIG_PHYLIB is enabled
This problem was introduced by 48c8b96f21
* tag 'renesas-fixes-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: Fix GPIO resources in DTS
irqchip: renesas-intc-irqpin: Fix register bitfield shift calculation
ARM: shmobile: lager: phy fixup needs CONFIG_PHYLIB
Signed-off-by: Kevin Hilman <khilman@linaro.org>
From Uwe Kleine-König:
* efm32/soc: (1003 commits)
ARM: device trees for Energy Micro's EFM32 Cortex-M3 SoCs
ARM: new platform for Energy Micro's EFM32 Cortex-M3 SoCs
+Linux 3.13-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>
In the Armada 370/XP driver, when we receive an IRQ 1, we read the
list of doorbells that caused the interrupt from register
ARMADA_370_XP_IN_DRBEL_CAUSE_OFFS. This gives the list of MSIs that
were generated. However, instead of acknowledging only the MSIs that
were generated, we acknowledge *all* the MSIs, by writing
~MSI_DOORBELL_MASK in the ARMADA_370_XP_IN_DRBEL_CAUSE_OFFS register.
This creates a race condition: if a new MSI that isn't part of the
ones read into the temporary "msimask" variable is fired before we
acknowledge all MSIs, then we will simply loose it.
It is important to mention that this ARMADA_370_XP_IN_DRBEL_CAUSE_OFFS
register has the following behavior: "A CPU write of 0 clears the bits
in this field. A CPU write of 1 has no effect". This is what allows us
to simply write ~msimask to acknoledge the handled MSIs.
Notice that the same problem is present in the IPI implementation, but
it is fixed as a separate patch, so that this IPI fix can be pushed to
older stable versions as appropriate (all the way to 3.8), while the
MSI code only appeared in 3.13.
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In the Armada 370/XP driver, when we receive an IRQ 0, we read the
list of doorbells that caused the interrupt from register
ARMADA_370_XP_IN_DRBEL_CAUSE_OFFS. This gives the list of IPIs that
were generated. However, instead of acknowledging only the IPIs that
were generated, we acknowledge *all* the IPIs, by writing
~IPI_DOORBELL_MASK in the ARMADA_370_XP_IN_DRBEL_CAUSE_OFFS register.
This creates a race condition: if a new IPI that isn't part of the
ones read into the temporary "ipimask" variable is fired before we
acknowledge all IPIs, then we will simply loose it. This is causing
scheduling hangs on SMP intensive workloads.
It is important to mention that this ARMADA_370_XP_IN_DRBEL_CAUSE_OFFS
register has the following behavior: "A CPU write of 0 clears the bits
in this field. A CPU write of 1 has no effect". This is what allows us
to simply write ~ipimask to acknoledge the handled IPIs.
Notice that the same problem is present in the MSI implementation, but
it will be fixed as a separate patch, so that this IPI fix can be
pushed to older stable versions as appropriate (all the way to 3.8),
while the MSI code only appeared in 3.13.
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: stable@vger.kernel.org # v3.8+
Fixes: 344e873e56 'arm: mvebu: Add IPI support via doorbells'
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This adds an irqchip driver and corresponding devicetree binding for the
secondary interrupt controllers based on Synopsys DesignWare IP dw_apb_ictl.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
