Commit Graph

3685 Commits

Author SHA1 Message Date
Colin Ian King bead21687f i2c-stm32f4: remove redundant initialization of pointer reg
The pointer reg is assigned a value that is never read, it is later
overwritten with a new value, hence the redundant initialization can
be removed.

Cleans up clang warning:
drivers/i2c/busses/i2c-stm32f4.c:352:16: warning: Value stored to 'reg'
during its initialization is never read

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-02-27 13:51:05 +01:00
Andrzej Hajda 939c5a46e5 i2c: exynos5: rework HSI2C_MASTER_ST_LOSE state handling
HSI2C_MASTER_ST_LOSE state is not documented properly, extensive tests
show that hardware is usually able to recover from this state without
interrupting the transfer. Moreover documentation says that
such state can be caused by slave clock stretching, and should not be
treated as an error during transaction. The only place it indicates
an error is just before starting transaction. In such case bus recovery
procedure should be performed - master should pulse SCL line nine times
and then send STOP condition, it can be repeated until SDA goes high.
The procedure can be performed using manual commands HSI2C_CMD_READ_DATA
and HSI2C_CMD_SEND_STOP.

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-02-27 13:47:28 +01:00
George Cherian 41b1d4de96 i2c: xlp9xx: Handle transactions with I2C_M_RECV_LEN properly
In case of transaction with I2C_M_RECV_LEN set, make sure the driver reads
the first byte and then updates the RX fifo with the expected length. Set
threshold to 1 byte so that driver gets an interrupt on receiving the first byte.
After which the transfer length is updated depending on the received length.
Also report SMBus block read functionality.

Signed-off-by: George Cherian <george.cherian@cavium.com>
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-02-26 21:16:11 +01:00
Dmitry Bazhenov c2a3b3cce8 i2c: xlp9xx: return ENXIO on slave address NACK
Fix the driver violation of the common practice to return
ENXIO error on a slave address NACK.

Signed-off-by: Dmitry Bazhenov <dmitry.bazhenov@auriga.com>
Signed-off-by: George Cherian <george.cherian@cavium.com>
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-02-26 21:14:09 +01:00
Wolfram Sang a1671af286 i2c: of: simplify reading the "reg" property
of_get_property() is a bit cumbersome to use. Replace it with the newer
of_property_read_u32() for more readable code.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-02-26 20:40:46 +01:00
Wolfram Sang 4f3ae38acb i2c: of: remove duplicated check for valid address
The very same check is done when calling i2c_new_device(). Remove it
here to avoid code duplication.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-02-26 20:40:46 +01:00
Wolfram Sang c49b0e0775 i2c: of: rename variable to meet expectations
'result' is mostly used in the kernel as int for functions returning
errno on failure. Here it is a pointer to the client struct, so let's
call it this way (as the parent function does, too).

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-02-26 20:40:46 +01:00
Wolfram Sang e6db2d3278 i2c: of: make ref counting more visible
When debugging a ref counting problem, I overlooked this snipplet a few
times. Might be taste, but I think the new location is visually easier
recognizable.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-02-26 20:40:46 +01:00
Wolfram Sang f1c87ceb02 i2c: of: change log level of failed device creation
If we cannot create a device, this is an error, not a warning. Fix the
log level.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-02-26 20:40:46 +01:00
Andy Shevchenko d1fa74520d i2c: designware: Consider SCL GPIO optional
GPIO library can return -ENOSYS for the failed request.
Instead of failing ->probe() in this case override error code to 0.

Fixes: ca382f5b38 ("i2c: designware: add i2c gpio recovery option")
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-02-22 12:15:35 +01:00
Patryk Kocielnik c396b9a03e i2c: busses: i2c-sirf: Fix spelling: "formular" -> "formula".
Fix spelling.

Signed-off-by: Patryk Kocielnik <patryk.kocielnik@gmail.com>
[wsa: fixed "Initialization", too]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-02-22 12:12:35 +01:00
Eric Anholt fe32a815f0 i2c: bcm2835: Set up the rising/falling edge delays
We were leaving them in the power on state (or the state the firmware
had set up for some client, if we were taking over from them).  The
boot state was 30 core clocks, when we actually want to sample some
time after (to make sure that the new input bit has actually arrived).

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2018-02-22 12:11:07 +01:00
Jarkko Nikula 1540779883 i2c: i801: Add missing documentation entries for Braswell and Kaby Lake
Commits adding PCI IDs for Intel Braswell and Kaby Lake PCH-H lacked the
respective Kconfig and Documentation/i2c/busses/i2c-i801 change. Add
them now.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-02-21 09:17:20 +01:00
Ben Gardner fba4adbbf6 i2c: designware: must wait for enable
One I2C bus on my Atom E3845 board has been broken since 4.9.
It has two devices, both declared by ACPI and with built-in drivers.

There are two back-to-back transactions originating from the kernel, one
targeting each device. The first transaction works, the second one locks
up the I2C controller. The controller never recovers.

These kernel logs show up whenever an I2C transaction is attempted after
this failure.
i2c-designware-pci 0000:00:18.3: timeout in disabling adapter
i2c-designware-pci 0000:00:18.3: timeout waiting for bus ready

Waiting for the I2C controller status to indicate that it is enabled
before programming it fixes the issue.

I have tested this patch on 4.14 and 4.15.

Fixes: commit 2702ea7dbe ("i2c: designware: wait for disable/enable only if necessary")
Cc: linux-stable <stable@vger.kernel.org> #4.13+
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-02-21 09:15:47 +01:00
Linus Torvalds 4141cf676b Merge branch 'i2c/for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
 "I2C has the following changes for you:

   - new flag to mark DMA safe buffers in i2c_msg. Also, some
     infrastructure around it. And docs.

   - huge refactoring of the at24 driver led by the new maintainer
     Bartosz

   - update I2C bus recovery to send STOP after recovery

   - conversion from gpio to gpiod for I2C bus recovery

   - adding a fault-injector to the i2c-gpio driver

   - lots of small driver improvements, and bigger ones to
     i2c-sh_mobile"

* 'i2c/for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (99 commits)
  i2c: mv64xxx: Add myself as maintainer for this driver
  i2c: mv64xxx: Fix clock resource by adding an optional bus clock
  i2c: mv64xxx: Remove useless test before clk_disable_unprepare
  i2c: mxs: use true and false for boolean values
  i2c: meson: update doc description to fix build warnings
  i2c: meson: add configurable divider factors
  dt-bindings: i2c: update documentation for the Meson-AXG
  i2c: imx-lpi2c: add runtime pm support
  i2c: rcar: fix some trivial typos in comments
  i2c: davinci: fix the cpufreq transition
  i2c: rk3x: add proper kerneldoc header
  i2c: rk3x: account for const type of of_device_id.data
  i2c: acorn: remove outdated path from file header
  i2c: acorn: add MODULE_LICENSE tag
  i2c: rcar: implement bus recovery
  i2c: send STOP after successful bus recovery
  i2c: ensure SDA is released in recovery if SDA is controllable
  i2c: add 'set_sda' to bus_recovery_info
  i2c: add identifier in declarations for i2c_bus_recovery
  i2c: make kerneldoc about bus recovery more precise
  ...
2018-02-04 10:57:43 -08:00
Linus Torvalds adbc128fa8 ARM: SoC platform updates for 4.16
These are mostly minor bugfixes, cleanup and many defconfig updates to
 support added drivers. In particular OMAP and PXA keep cleaning up the
 legacy code base, as usual.
 
 Nvidia adds some more SoC support code for Tegra 186.
 
 For the first time on years, we are actually adding a non-DT platform for,
 the EP93xx based Liebherr controller BK3.1. It's a minor variation of
 the EP93xx reference design and in active use, while EP93xx apparently
 doesn't have enough new development to have any device tree support.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJac0azAAoJEGCrR//JCVInuaAQAJBfJeqhFC01JeO+Oy/Sz3qh
 WuZpT0ExfU1EFLnyBhEYJujDmlzNPcVacI53gSazpiksHboLpOodW+pX19NwOyzC
 RSbyLa+W5MH1uXtIzV8dqwXboOWJ/Fh348VTSG4dw2JJ6i4k3U/9xboOVtnynCic
 ww66FEEpFvJfNgch+7zcpHDwACqJ8nsrortNzEM8eV2jA/DOgv48EemTJqf1Lv1E
 Z0nqIBEPvInPgCB3MX3KTD6CgbQ1qZOcWcEgR1tDRqmCuCgvp4xawiOBKos6QHaG
 Iqgi3jI5rPJ391mhIQqK5duU5IKMY0FO6qxir7U+YNZm8vMmijPMwgEmlkG28mTT
 6B7+ZNHXnSnFklpMetvCBDB8a+Lximft/oqecumowKJo0R9vZontnP4Jdbt9HLic
 T99nzw2Xwhxo/J7kQXcGDoLyRAPgS1iiHyWXKbXADRlaftACeXL9iVTg+F9EAveq
 WTDNmN6hbha4fN5PXUkcTAco96JtevT/H2ZDmYFBCSaqHy3QrNPJtDcVSIJd4CGT
 uQJwXINHvR/nJrEl2ZLLsfMSJMBXWp79w7xb+QfkIa6UXL3hUwGC9Wd2jQZsdHf3
 AQ/Q1oJ6epCvd2+4xo0EwiUMjr2MGqfLmtGBQkMzdSbFe50RhHe3w2Amy3VU03X+
 vFB4zAmReWDZXgQ7+Dhg
 =frm4
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC platform updates from Arnd Bergmann:
 "These are mostly minor bugfixes, cleanup and many defconfig updates to
  support added drivers. In particular OMAP and PXA keep cleaning up the
  legacy code base, as usual.

  Nvidia adds some more SoC support code for Tegra 186.

  For the first time on years, we are actually adding a non-DT platform
  for the EP93xx based Liebherr controller BK3.1. It's a minor variation
  of the EP93xx reference design and in active use, while EP93xx
  apparently doesn't have enough new development to have any device tree
  support"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
  ARM: omap: hwmod: fix section mismatch warnings
  ARM: pxa/tosa-bt: add MODULE_LICENSE tag
  arm64: defconfig: enable CONFIG_ACPI_APEI_EINJ
  arm64: defconfig: enable EDAC GHES option
  arm64: defconfig: enable CONFIG_ACPI_APEI_MEMORY_FAILURE
  ARM: imx_v6_v7_defconfig: enable CONFIG_CPU_FREQ_STAT
  Wind down ARM/TANGO port
  ARM: davinci: constify gpio_led
  ARM: davinci: drop unneeded newline
  soc: Add SoC driver for Gemini
  ARM: SAMSUNG: Add SPDX license identifiers
  ARM: S5PV210: Add SPDX license identifiers
  ARM: S3C64XX: Add SPDX license identifiers
  ARM: S3C24XX: Add SPDX license identifiers
  ARM: EXYNOS: Add SPDX license identifiers
  ARM: imx: remove unused imx3 pm definitions
  ARM: imx: don't abort MMDC probe if power saving status doesn't match
  ARM: imx_v6_v7_defconfig: enable RTC_DRV_MXC_V2
  ARM: imx_v6_v7_defconfig: Add missing config for DART-MX6 SoM
  ARM: davinci: Use PTR_ERR_OR_ZERO()
  ...
2018-02-01 16:17:40 -08:00
Linus Torvalds 7f3fdd40a7 Power management updates for v4.16-rc1
- Define a PM driver flag allowing drivers to request that their
    devices be left in suspend after system-wide transitions to the
    working state if possible and add support for it to the PCI bus
    type and the ACPI PM domain (Rafael Wysocki).
 
  - Make the PM core carry out optimizations for devices with driver
    PM flags set in some cases and make a few drivers set those flags
    (Rafael Wysocki).
 
  - Fix and clean up wrapper routines allowing runtime PM device
    callbacks to be re-used for system-wide PM, change the generic
    power domains (genpd) framework to stop using those routines
    incorrectly and fix up a driver depending on that behavior of
    genpd (Rafael Wysocki, Ulf Hansson, Geert Uytterhoeven).
 
  - Fix and clean up the PM core's device wakeup framework and
    re-factor system-wide PM core code related to device wakeup
    (Rafael Wysocki, Ulf Hansson, Brian Norris).
 
  - Make more x86-based systems use the Low Power Sleep S0 _DSM
    interface by default (to fix power button wakeup from
    suspend-to-idle on Surface Pro3) and add a kernel command line
    switch to tell it to ignore the system sleep blacklist in the
    ACPI core (Rafael Wysocki).
 
  - Fix a race condition related to cpufreq governor module removal
    and clean up the governor management code in the cpufreq core
    (Rafael Wysocki).
 
  - Drop the unused generic code related to the handling of the static
    power energy usage model in the CPU cooling thermal driver along
    with the corresponding documentation (Viresh Kumar).
 
  - Add mt2712 support to the Mediatek cpufreq driver (Andrew-sh Cheng).
 
  - Add a new operating point to the imx6ul and imx6q cpufreq drivers
    and switch the latter to using clk_bulk_get() (Anson Huang, Dong
    Aisheng).
 
  - Add support for multiple regulators to the TI cpufreq driver along
    with a new DT binding related to that and clean up that driver
    somewhat (Dave Gerlach).
 
  - Fix a powernv cpufreq driver regression leading to incorrect CPU
    frequency reporting, fix that driver to deal with non-continguous
    P-states correctly and clean it up (Gautham Shenoy, Shilpasri Bhat).
 
  - Add support for frequency scaling on Armada 37xx SoCs through the
    generic DT cpufreq driver (Gregory CLEMENT).
 
  - Fix error code paths in the mvebu cpufreq driver (Gregory CLEMENT).
 
  - Fix a transition delay setting regression in the longhaul cpufreq
    driver (Viresh Kumar).
 
  - Add Skylake X (server) support to the intel_pstate cpufreq driver
    and clean up that driver somewhat (Srinivas Pandruvada).
 
  - Clean up the cpufreq statistics collection code (Viresh Kumar).
 
  - Drop cluster terminology and dependency on physical_package_id
    from the PSCI driver and drop dependency on arm_big_little from
    the SCPI cpufreq driver (Sudeep Holla).
 
  - Add support for system-wide suspend and resume to the RAPL power
    capping driver and drop a redundant semicolon from it (Zhen Han,
    Luis de Bethencourt).
 
  - Make SPI domain validation (in the SCSI SPI transport driver) and
    system-wide suspend mutually exclusive as they rely on the same
    underlying mechanism and cannot be carried out at the same time
    (Bart Van Assche).
 
  - Fix the computation of the amount of memory to preallocate in the
    hibernation core and clean up one function in there (Rainer Fiebig,
    Kyungsik Lee).
 
  - Prepare the Operating Performance Points (OPP) framework for being
    used with power domains and clean up one function in it (Viresh
    Kumar, Wei Yongjun).
 
  - Clean up the generic sysfs interface for device PM (Andy Shevchenko).
 
  - Fix several minor issues in power management frameworks and clean
    them up a bit (Arvind Yadav, Bjorn Andersson, Geert Uytterhoeven,
    Gustavo Silva, Julia Lawall, Luis de Bethencourt, Paul Gortmaker,
    Sergey Senozhatsky, gaurav jindal).
 
  - Make it easier to disable PM via Kconfig (Mark Brown).
 
  - Clean up the cpupower and intel_pstate_tracer utilities (Doug
    Smythies, Laura Abbott).
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJaYw2iAAoJEILEb/54YlRxLHwP/iabmAcbXBeg30/wSCKcWB6f
 Ar785YbkFedNP7b2dypR7bcKIkaV55EExNHHoVuvC6gKrW+zx3F39v9QzK3HBKfw
 DgLWMjxR5Xdm9o8o2chsBEMl0itSRB9s864s+AAAElP+qjyT6kmbFyRFgVYLiNH0
 v9jNhPF9EmirViwES/syELa/P1AJDMxCb/SbRY+Xp1sPhGKlx2J/2eQsVDs7G+wL
 2BJeyBqwL9D78U/eY2bvpCoZLpmZmklx1eY5iK3Mzo6LZKYMaSypgkGuRfh//K+a
 8vFLwOBsOlpZ8lsPBRatV5+SMu8qMQMTnstui1m3/9bOPFfjymat6u0lLw4BV2hv
 zrNfqWOiwTAt/fczR1/naYuuSeRCLABvYDKjs/9iYdrCZYJ+n+ZzU/wi5geswDtD
 cQKDMOdOBrnfkN0Vqpw6ZBqun0RDldNT/+6oy93tHWBlF0CA4mMq5jr8q3iH35CW
 8TA1GCkurHZXTyYdYXR5SUHxPbOgZC87GAb7RlFEJJnvvkmy3jmBng675Hl5XAn7
 D8eJp3d4h5n121pkMLGcBc7K036T2uFsjrHWx+QsjKFUBWUBnuRfInRrLA5WnGo2
 U+KIEUPepdnbFFvYNv+kTgz2uE6FOqycEmnUKUKWUZYPN0GDAOw/V3813uxVRYtq
 27omIOL7PJp1wWjQnfXK
 =dnb7
 -----END PGP SIGNATURE-----

Merge tag 'pm-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull power management updates from Rafael Wysocki:
 "This includes some infrastructure changes in the PM core, mostly
  related to integration between runtime PM and system-wide suspend and
  hibernation, plus some driver changes depending on them and fixes for
  issues in that area which have become quite apparent recently.

  Also included are changes making more x86-based systems use the Low
  Power Sleep S0 _DSM interface by default, which turned out to be
  necessary to handle power button wakeups from suspend-to-idle on
  Surface Pro3.

  On the cpufreq front we have fixes and cleanups in the core, some new
  hardware support, driver updates and the removal of some unused code
  from the CPU cooling thermal driver.

  Apart from this, the Operating Performance Points (OPP) framework is
  prepared to be used with power domains in the future and there is a
  usual bunch of assorted fixes and cleanups.

  Specifics:

   - Define a PM driver flag allowing drivers to request that their
     devices be left in suspend after system-wide transitions to the
     working state if possible and add support for it to the PCI bus
     type and the ACPI PM domain (Rafael Wysocki).

   - Make the PM core carry out optimizations for devices with driver PM
     flags set in some cases and make a few drivers set those flags
     (Rafael Wysocki).

   - Fix and clean up wrapper routines allowing runtime PM device
     callbacks to be re-used for system-wide PM, change the generic
     power domains (genpd) framework to stop using those routines
     incorrectly and fix up a driver depending on that behavior of genpd
     (Rafael Wysocki, Ulf Hansson, Geert Uytterhoeven).

   - Fix and clean up the PM core's device wakeup framework and
     re-factor system-wide PM core code related to device wakeup
     (Rafael Wysocki, Ulf Hansson, Brian Norris).

   - Make more x86-based systems use the Low Power Sleep S0 _DSM
     interface by default (to fix power button wakeup from
     suspend-to-idle on Surface Pro3) and add a kernel command line
     switch to tell it to ignore the system sleep blacklist in the ACPI
     core (Rafael Wysocki).

   - Fix a race condition related to cpufreq governor module removal and
     clean up the governor management code in the cpufreq core (Rafael
     Wysocki).

   - Drop the unused generic code related to the handling of the static
     power energy usage model in the CPU cooling thermal driver along
     with the corresponding documentation (Viresh Kumar).

   - Add mt2712 support to the Mediatek cpufreq driver (Andrew-sh
     Cheng).

   - Add a new operating point to the imx6ul and imx6q cpufreq drivers
     and switch the latter to using clk_bulk_get() (Anson Huang, Dong
     Aisheng).

   - Add support for multiple regulators to the TI cpufreq driver along
     with a new DT binding related to that and clean up that driver
     somewhat (Dave Gerlach).

   - Fix a powernv cpufreq driver regression leading to incorrect CPU
     frequency reporting, fix that driver to deal with non-continguous
     P-states correctly and clean it up (Gautham Shenoy, Shilpasri
     Bhat).

   - Add support for frequency scaling on Armada 37xx SoCs through the
     generic DT cpufreq driver (Gregory CLEMENT).

   - Fix error code paths in the mvebu cpufreq driver (Gregory CLEMENT).

   - Fix a transition delay setting regression in the longhaul cpufreq
     driver (Viresh Kumar).

   - Add Skylake X (server) support to the intel_pstate cpufreq driver
     and clean up that driver somewhat (Srinivas Pandruvada).

   - Clean up the cpufreq statistics collection code (Viresh Kumar).

   - Drop cluster terminology and dependency on physical_package_id from
     the PSCI driver and drop dependency on arm_big_little from the SCPI
     cpufreq driver (Sudeep Holla).

   - Add support for system-wide suspend and resume to the RAPL power
     capping driver and drop a redundant semicolon from it (Zhen Han,
     Luis de Bethencourt).

   - Make SPI domain validation (in the SCSI SPI transport driver) and
     system-wide suspend mutually exclusive as they rely on the same
     underlying mechanism and cannot be carried out at the same time
     (Bart Van Assche).

   - Fix the computation of the amount of memory to preallocate in the
     hibernation core and clean up one function in there (Rainer Fiebig,
     Kyungsik Lee).

   - Prepare the Operating Performance Points (OPP) framework for being
     used with power domains and clean up one function in it (Viresh
     Kumar, Wei Yongjun).

   - Clean up the generic sysfs interface for device PM (Andy
     Shevchenko).

   - Fix several minor issues in power management frameworks and clean
     them up a bit (Arvind Yadav, Bjorn Andersson, Geert Uytterhoeven,
     Gustavo Silva, Julia Lawall, Luis de Bethencourt, Paul Gortmaker,
     Sergey Senozhatsky, gaurav jindal).

   - Make it easier to disable PM via Kconfig (Mark Brown).

   - Clean up the cpupower and intel_pstate_tracer utilities (Doug
     Smythies, Laura Abbott)"

* tag 'pm-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (89 commits)
  PCI / PM: Remove spurious semicolon
  cpufreq: scpi: remove arm_big_little dependency
  drivers: psci: remove cluster terminology and dependency on physical_package_id
  powercap: intel_rapl: Fix trailing semicolon
  dmaengine: rcar-dmac: Make DMAC reinit during system resume explicit
  PM / runtime: Allow no callbacks in pm_runtime_force_suspend|resume()
  PM / hibernate: Drop unused parameter of enough_swap
  PM / runtime: Check ignore_children in pm_runtime_need_not_resume()
  PM / runtime: Rework pm_runtime_force_suspend/resume()
  PM / genpd: Stop/start devices without pm_runtime_force_suspend/resume()
  cpufreq: powernv: Dont assume distinct pstate values for nominal and pmin
  cpufreq: intel_pstate: Add Skylake servers support
  cpufreq: intel_pstate: Replace bxt_funcs with core_funcs
  platform/x86: surfacepro3: Support for wakeup from suspend-to-idle
  ACPI / PM: Use Low Power S0 Idle on more systems
  PM / wakeup: Print warn if device gets enabled as wakeup source during sleep
  PM / domains: Don't skip driver's ->suspend|resume_noirq() callbacks
  PM / core: Propagate wakeup_path status flag in __device_suspend_late()
  PM / core: Re-structure code for clearing the direct_complete flag
  powercap: add suspend and resume mechanism for SOC power limit
  ...
2018-01-29 09:47:41 -08:00
Gregory CLEMENT 1534156e99 i2c: mv64xxx: Fix clock resource by adding an optional bus clock
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.

The binding documentation is updating accordingly.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-26 18:51:03 +01:00
Gregory CLEMENT a9e94bb80e i2c: mv64xxx: Remove useless test before clk_disable_unprepare
clk_disable_unprepare() already checks that the clock pointer is valid.
No need to test it before calling it.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-26 18:49:45 +01:00
Gustavo A. R. Silva 4be49b5d65 i2c: mxs: use true and false for boolean values
Assign true or false to boolean variables instead of an integer value.

This issue was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-26 18:34:50 +01:00
Yixun Lan 7e4c9d9e50 i2c: meson: update doc description to fix build warnings
Add description for 'data' parameter and drop unused 'irq' memeber.

Here is the warnings:
drivers/i2c/busses/i2c-meson.c:103: warning: No description found for
parameter 'data'
drivers/i2c/busses/i2c-meson.c:103: warning: Excess struct member 'irq'
description in 'meson_i2c'

Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-26 18:33:44 +01:00
Jian Hu 931b18e92c i2c: meson: add configurable divider factors
This patch try to add support for I2C controller in Meson-AXG SoC,
Due to the IP changes between I2C controller, we need to introduce
a compatible data to make the divider factor configurable.

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-24 07:24:55 +01:00
Fugang Duan 13d6eb20fc i2c: imx-lpi2c: add runtime pm support
Add runtime pm support to dynamically manage the clock to avoid enable/disable
clock in frequently that can improve the i2c bus transfer performance.

And use pm_runtime_force_suspend/resume() instead of lpi2c_imx_suspend/resume().

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-24 07:20:30 +01:00
Wolfram Sang fe34fbf93f i2c: rcar: fix some trivial typos in comments
Nothing big, but they get annoying after a while ;)

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-24 07:16:34 +01:00
Bartosz Golaszewski 19cfcafd7f i2c: davinci: fix the cpufreq transition
i2c_davinci_cpufreq_transition() is implemented in a way that will
block if it ever gets called while no transfer is in progress.

Not only that, but reinit_completion() is never called for xfr_complete.

Use the fact that cpufreq uses an srcu_notifier (running in process
context) for transitions and that the bus_lock is taken during the call
to master_xfer() and simplify the code by removing the transfer
completion entirely and protecting i2c_davinci_cpufreq_transition()
with i2c_lock/unlock_adapter().

Reported-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-24 07:14:59 +01:00
Rafael J. Wysocki 4b67157f04 Merge branch 'pm-core'
* pm-core: (29 commits)
  dmaengine: rcar-dmac: Make DMAC reinit during system resume explicit
  PM / runtime: Allow no callbacks in pm_runtime_force_suspend|resume()
  PM / runtime: Check ignore_children in pm_runtime_need_not_resume()
  PM / runtime: Rework pm_runtime_force_suspend/resume()
  PM / wakeup: Print warn if device gets enabled as wakeup source during sleep
  PM / core: Propagate wakeup_path status flag in __device_suspend_late()
  PM / core: Re-structure code for clearing the direct_complete flag
  PM: i2c-designware-platdrv: Optimize power management
  PM: i2c-designware-platdrv: Use DPM_FLAG_SMART_PREPARE
  PM / mfd: intel-lpss: Use DPM_FLAG_SMART_SUSPEND
  PCI / PM: Use SMART_SUSPEND and LEAVE_SUSPENDED flags for PCIe ports
  PM / wakeup: Add device_set_wakeup_path() helper to control wakeup path
  PM / core: Assign the wakeup_path status flag in __device_prepare()
  PM / wakeup: Do not fail dev_pm_attach_wake_irq() unnecessarily
  PM / core: Direct DPM_FLAG_LEAVE_SUSPENDED handling
  PM / core: Direct DPM_FLAG_SMART_SUSPEND optimization
  PM / core: Add helpers for subsystem callback selection
  PM / wakeup: Drop redundant check from device_init_wakeup()
  PM / wakeup: Drop redundant check from device_set_wakeup_enable()
  PM / wakeup: only recommend "call"ing device_init_wakeup() once
  ...
2018-01-18 02:55:09 +01:00
Wolfram Sang 5bacb56b2b i2c: rk3x: add proper kerneldoc header
gcc noticed the kerneldoc was wrongly formatted. Fix it!

drivers/i2c/busses/i2c-rk3x.c:164: warning:
  Cannot understand  * @grf_offset: ...
  on line 164 - I thought it was a doc line

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
2018-01-18 00:34:09 +01:00
Julia Lawall d032a2eb2e i2c: rk3x: account for const type of of_device_id.data
This driver creates a number of const structures that it stores in
the data field of an of_device_id array.

The data field of an of_device_id structure has type const void *, so
there is no need for a const-discarding cast when putting const values
into such a structure.

Furthermore, adding const to the declaration of the location that
receives a const value from such a field ensures that the compiler
will continue to check that the value is not modified.  The
const-discarding cast on the extraction from the data field is thus
no longer needed.

Done using Coccinelle.

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-18 00:10:30 +01:00
Wolfram Sang f89813ec8b i2c: acorn: remove outdated path from file header
That path has gone away for a long time. Move the HW name upwards for a
proper header.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-18 00:08:20 +01:00
Arnd Bergmann e199c285b6 i2c: acorn: add MODULE_LICENSE tag
As of v4.15, Kbuild warns about missing MODULE_LICENSE tags:

WARNING: modpost: missing MODULE_LICENSE() in drivers/i2c/busses/i2c-acorn.o

This adds a license, author and description tag, matching the
comment at the start of the acorn i2c driver.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-18 00:05:58 +01:00
Jeremy Compostella 89c6efa61f i2c: core-smbus: prevent stack corruption on read I2C_BLOCK_DATA
On a I2C_SMBUS_I2C_BLOCK_DATA read request, if data->block[0] is
greater than I2C_SMBUS_BLOCK_MAX + 1, the underlying I2C driver writes
data out of the msgbuf1 array boundary.

It is possible from a user application to run into that issue by
calling the I2C_SMBUS ioctl with data.block[0] greater than
I2C_SMBUS_BLOCK_MAX + 1.

This patch makes the code compliant with
Documentation/i2c/dev-interface by raising an error when the requested
size is larger than 32 bytes.

Call Trace:
 [<ffffffff8139f695>] dump_stack+0x67/0x92
 [<ffffffff811802a4>] panic+0xc5/0x1eb
 [<ffffffff810ecb5f>] ? vprintk_default+0x1f/0x30
 [<ffffffff817456d3>] ? i2cdev_ioctl_smbus+0x303/0x320
 [<ffffffff8109a68b>] __stack_chk_fail+0x1b/0x20
 [<ffffffff817456d3>] i2cdev_ioctl_smbus+0x303/0x320
 [<ffffffff81745aed>] i2cdev_ioctl+0x4d/0x1e0
 [<ffffffff811f761a>] do_vfs_ioctl+0x2ba/0x490
 [<ffffffff81336e43>] ? security_file_ioctl+0x43/0x60
 [<ffffffff811f7869>] SyS_ioctl+0x79/0x90
 [<ffffffff81a22e97>] entry_SYSCALL_64_fastpath+0x12/0x6a

Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2018-01-17 15:35:21 +01:00
Lixin Wang e0638fa400 i2c: core: decrease reference count of device node in i2c_unregister_device
Reference count of device node was increased in of_i2c_register_device,
but without decreasing it in i2c_unregister_device. Then the added
device node will never be released. Fix this by adding the of_node_put.

Signed-off-by: Lixin Wang <alan.1.wang@nokia-sbell.com>
Tested-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2018-01-17 15:23:31 +01:00
Wolfram Sang 7d2c17f021 i2c: rcar: implement bus recovery
We can force levels of SCL and SDA, so we can use that for bus recovery.
Note that we cannot read SDA back, because we will only get the internal
state of the bus free detection.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-16 00:04:48 +01:00
Wolfram Sang 2806e6ad77 i2c: send STOP after successful bus recovery
If we managed to get a client release SDA again, send a STOP afterwards
to make sure we have a consistent state on the bus again.

Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-16 00:04:42 +01:00
Wolfram Sang 72b08fcc15 i2c: ensure SDA is released in recovery if SDA is controllable
If we have a function to control SDA, we should ensure that SDA is not
held down by us. So, release the GPIO in this case.

Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-16 00:04:30 +01:00
Wolfram Sang 8092178ffe i2c: add 'set_sda' to bus_recovery_info
This will be needed when we want to create STOP conditions, too, later.
Create the needed fields and populate them for the GPIO case if the GPIO
is set to output.

Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-16 00:04:19 +01:00
Andrzej Hajda 4d3ea4e1c3 i2c: exynos5: change internal transmission timeout to 100ms
Exynos-I2C uses default timeout of 1 second for the whole transaction,
including re-transmissions due to arbitration lost errors (-EAGAIN).
To allow re-transmissions driver's internal timeout should be significantly
lower, 100ms seems to be good candidate.

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15 21:54:28 +01:00
Radu Rendec 5cd5f0bb0d i2c: ismt: 16-byte align the DMA buffer address
Use only a portion of the data buffer for DMA transfers, which is always
16-byte aligned. This makes the DMA buffer address 16-byte aligned and
compensates for spurious hardware parity errors that may appear when the
DMA buffer address is not 16-byte aligned.

The data buffer is enlarged in order to accommodate any possible 16-byte
alignment offset and changes the DMA code to only use a portion of the
data buffer, which is 16-byte aligned.

The symptom of the hardware issue is the same as the one addressed in
v3.12-rc2-5-gbf41691 and manifests by transfers failing with EIO, with
bit 9 being set in the ERRSTS register.

Signed-off-by: Radu Rendec <radu.rendec@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15 21:02:43 +01:00
Arseny Solokha 38a99bd773 i2c: mpc: always determine I2C clock prescaler at runtime
Remove the facility for setting the prescaler value at compile time
entirely. It was only used for two SoCs, duplicating the actual value
for one of them and setting sometimes bogus value for another. Make all
MPC8xxx SoCs obtain their actual I2C clock prescaler from a single place
in the code.

Changes from v2:
- left Device Tree compatibles in place

Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15 19:19:55 +01:00
Arseny Solokha 7575a745f9 i2c: mpc: fix PORDEVSR2 mask for MPC8533/44
According to the reference manuals for the corresponding SoCs, SEC
frequency ratio configuration is indicated by bit 26 of the POR Device
Status Register 2. Consequently, SEC_CFG bit should be tested by mask 0x20,
not 0x80. Testing the wrong bit leads to selection of wrong I2C clock
prescaler on those SoCs.

Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15 19:16:14 +01:00
Arseny Solokha f6214f6f2b i2c: mpc: unify obtaining the MPC8533/44 I2C clock prescaler w/ MPC8xxx
Commit 8ce795cb0c ("i2c: mpc: assign the correct prescaler from SVR")
introduced the common helper function for obtaining the actual clock
prescaler value for MPC85xx. However, getting the prescaler for MPC8544
which depends on the SEC frequency ratio on this platform, has been always
performed separately based on the corresponding Device Tree configuration.

Move special handling of MPC8544 into that common helper. Make it dependent
on the SoC version and not on Device Tree compatible node, as is the case
with all other SoCs. Handle MPC8533 the same way which is similar
to MPC8544 in this regard, according to AN2919 "Determining the I2C
Frequency Divider Ratio for SCL".

Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15 19:13:33 +01:00
Arseny Solokha 6d10613919 i2c: mpc: get MPC8xxx I2C clock prescaler before using it in calculations
Obtaining the actual I2C clock prescaler value in mpc_i2c_setup_8xxx() only
happens when the clock parameter is set to something other than
MPC_I2C_CLOCK_LEGACY. When the clock parameter is exactly
MPC_I2C_CLOCK_LEGACY, the prescaler parameter is used in arithmetic
division as provided by the caller, resulting in a division by zero
for the majority of processors supported by the module.

Avoid division by zero by obtaining the actual I2C clock prescaler
in mpc_i2c_setup_8xxx() unconditionally regardless of the passed clock
value.

Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15 19:13:06 +01:00
Radu Rendec aad550f93f i2c: ismt: dump registers at the end of transactions
This patch dumps general and master registers at the end of transactions
when debugging is enabled. Previously, registers were only dumped before
submitting new descriptors (at the beginning of transactions).

This helps debugging if some registers change as result of a failed
transaction (e.g. bits are set in the ERRSTS general register).

Signed-off-by: Radu Rendec <radu.rendec@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15 18:03:56 +01:00
Wolfram Sang 6e318d9e37 i2c: sh_mobile: let r8a7790 (R-Car H2) use the new formula
Make use of the new formula for more precise bus frequencies.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15 18:01:14 +01:00
Wolfram Sang 4ecfb9d3b2 i2c: sh_mobile: add new frequency calculation for later SoC
The formula to generate the desired bus speeds has changed a little over
time. Implement the new formula and allow drivers to opt-in by changing
to this new config set. Ensure in probe that we don't divide by zero.
The returned values on a R-Car H2 (r8a7790/Lager board) match the
suggested values in the datasheet.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15 18:01:14 +01:00
Wolfram Sang c3449f73a8 i2c: sh_mobile: add helper to check frequency calculations
Because we will add a second formula soon, put the sanity checks for the
computed results into a separate function.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15 18:01:03 +01:00
Wolfram Sang 023c22fd82 i2c: sh_mobile: let RuntimePM do the clock handling
Start RuntimePM a bit earlier, so we can use it to enable the clock
during probe for frequency calculations. Make sure it is enabled before
calling setup().

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15 17:58:56 +01:00
Wolfram Sang b3750b6278 i2c: sh_mobile: require setup callback
Require the setup callback and move the frequency calculation into it.
This is in preparation for supporting multiple formulas.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15 17:58:50 +01:00
Wolfram Sang 12742b6ac1 i2c: sh_mobile: allow setup callback to return errno
The setup callback will be more generic and, thus, need to be able to
return error codes. Change the return type to 'int' for that.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15 17:58:45 +01:00
Wolfram Sang 9e42213116 i2c: sh_mobile: move type detection upwards
For refactoring reasons, we will need this information before the setup
callback. Also, simplify the comment to a oneliner.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15 17:58:39 +01:00
Rafael J. Wysocki 02e45646d5 PM: i2c-designware-platdrv: Optimize power management
Optimize the power management in i2c-designware-platdrv by making it
set the DPM_FLAG_SMART_SUSPEND and DPM_FLAG_LEAVE_SUSPENDED which
allows some code to be dropped from its PM callbacks.

First, setting DPM_FLAG_SMART_SUSPEND causes the intel-lpss driver
to avoid resuming i2c-designware-platdrv devices in its ->prepare
callback, so they can stay in runtime suspend after that point even
if the direct-complete feature is not used for them.

It also causes the ACPI PM domain and the PM core to avoid invoking
"late" and "noirq" suspend callbacks for these devices if they are
in runtime suspend at the beginning of the "late" phase of device
suspend during system suspend.  That guarantees dw_i2c_plat_suspend()
to be called for a device only if it is not in runtime suspend.

Moreover, it causes the device's runtime PM status to be set to
"active" after calling dw_i2c_plat_resume() for it, so the
driver doesn't need internal flags to avoid invoking either
dw_i2c_plat_suspend() or dw_i2c_plat_resume() twice in a row.

Second, setting DPM_FLAG_LEAVE_SUSPENDED enables the optimization
allowing the device to stay suspended after system resume under
suitable conditions, so again the driver doesn't need to take
care of that by itself.

Accordingly, the internal "suspended" and "skip_resume" flags
used by the driver are not necessary any more, so drop them and
simplify the driver's PM callbacks.

Additionally, notice that dw_i2c_plat_complete() only needs to
schedule runtime PM resume for the device if platform firmware
has been involved in resuming the system, so make it call
pm_resume_via_firmware() to check that.  Also make it check the
runtime PM status of the device instead of its direct_complete
flag which also works if the device remained suspended due to
the DPM_FLAG_LEAVE_SUSPENDED driver flag.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
2018-01-10 00:48:25 +01:00
Rafael J. Wysocki 422cb781e0 PM: i2c-designware-platdrv: Use DPM_FLAG_SMART_PREPARE
Modify i2c-designware-platdrv to set DPM_FLAG_SMART_PREPARE for its
devices and return 0 from the system suspend ->prepare callback
if the device has an ACPI companion object in order to tell the PM
core and middle layers to avoid skipping system suspend/resume
callbacks for the device in that case (which may be problematic,
because the device may be accessed during suspend and resume of
other devices via I2C operation regions then).

Also the pm_runtime_suspended() check in dw_i2c_plat_prepare()
is not necessary any more, because the core does it when setting
power.direct_complete for the device, so drop it.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
2018-01-10 00:48:25 +01:00
Olof Johansson add49f7835 This is the pxa changes for v4.16 cycle.
It is :
  - the conversion to the new parser sharpslpart parser
    for the Sharp variants
  - an I2C platform data cleanup for PXA
  - a gpioreg switch of one register for lubbock
 -----BEGIN PGP SIGNATURE-----
 
 iQJLBAABCAA1FiEExgkueSa0u8n4Ls+HA/Z63R24yxIFAlo6zngXHHJvYmVydC5q
 YXJ6bWlrQGZyZWUuZnIACgkQA/Z63R24yxI3Sw//ezB9Fkpg7Bqg4mZEhY50Gl+D
 vurIeat1gwcd1HJs0ard1oD9zf86tZd25ZU/HBnWPz/4vKY2ROM28STweuSb8Mvf
 EDN3D2nLbsDQQ1fCkhTrmVbnrj2xTZOz31t3QDubsr4M0o2lKgzpu6ImKqYB+BWV
 BIBPLFNKHnD0OMtTqU4gSlLTYML6kRw8nlND0uut/Xc71/mDrsnsedir1nwR5PVf
 mxSKE21JLamZ52KpBUtWRkvPjhb9tAdTB7ayCgBOUGB+gRGQqXAqb3eqnMdvSpMO
 WBVoFYav3tmBdZVLXoEzx1ZwkOitYV9imPMr9l5y68GiYuvrUL5V2AShjA+oeq2a
 N0SH15di34yeFtkhRPQDuL/+ex6P40CEu+U8gB3VznVwsE02TYggrJyaek+/iBJK
 MbgGM28KNUp4I3C0cbz6craWnDwIhwT6EfK7PJzGcy8zYUYcIr4Nn6tpRvmq5v/u
 /gJuP5oNb33sa73jt+M6+NPSqHECEljE0hGxW2oOJGKKSySKe51jDSP1Dvuvnpk8
 FBbuHbf3pCujKh1rq2vQjeWm8rtSVBoXLU9l0Vvs1tZZ80BCxurPfZ39LAua1Ea4
 cexEIs6MxY4NHxCNqMm7730cqizY9KX1N1UUEc2wVXdBh/xGGia/HPm6SsA1NgZ6
 b+zIK+5WY6wQc2/d1ts=
 =xz4R
 -----END PGP SIGNATURE-----

Merge tag 'pxa-for-4.16' of https://github.com/rjarzmik/linux into next/soc

This is the pxa changes for v4.16 cycle.

It is :
 - the conversion to the new parser sharpslpart parser
   for the Sharp variants
 - an I2C platform data cleanup for PXA
 - a gpioreg switch of one register for lubbock

* tag 'pxa-for-4.16' of https://github.com/rjarzmik/linux:
  ARM: pxa/lubbock: add GPIO driver for LUB_MISC_WR register
  ARM: pxa/poodle: Remove hardcoded partitioning, use sharpslpart parser
  ARM: pxa/spitz: Remove hardcoded partitioning, use sharpslpart parser
  ARM: pxa/tosa: Remove hardcoded partitioning, use sharpslpart parser
  ARM: pxa/corgi: Remove hardcoded partitioning, use sharpslpart parser
  ARM: pxa: move header file out of I2C realm
  ARM: pxa: move declarations to proper place

Signed-off-by: Olof Johansson <olof@lixom.net>
2018-01-04 23:10:08 -08:00
Jan Kundrát f11a04464a i2c: gpio: Enable working over slow can_sleep GPIOs
"Slow" GPIOs (usually those connected over an SPI or an I2C bus) are,
well, slow in their operation. It is generally a good idea to avoid
using them for time-critical operation, but sometimes the hardware just
sucks, and the software has to cope. In addition to that, the I2C bus
itself does not actually define any strict timing limits; the bus is
free to go all the way down to DC. The timeouts (and therefore the
slowest acceptable frequency) are present only in SMBus.

The `can_sleep` is IMHO a wrong concept to use here. My SPI-to-quad-UART
chip (MAX14830) is connected via a 26MHz SPI bus, and it happily drives
SCL at 200kHz (5µs pulses) during my benchmarks. That's faster than the
maximal allowed speed of the traditional I2C.

The previous version of this code did not really block operation over
slow GPIO pins, anyway. Instead, it just resorted to printing a warning
with a backtrace each time a GPIO pin was accessed, thereby slowing
things down even more.

Finally, it's not just me. A similar patch was originally submitted in
2015 [1].

[1] https://patchwork.ozlabs.org/patch/450956/

Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-04 01:02:55 +01:00
Jun Gao f6762cedbe i2c: mediatek: Enable i2c module clock before i2c registers access.
Make sure i2c module clock has been enabled before i2c registers
access.

Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-04 00:54:02 +01:00
Jun Gao 5a10e7d7aa i2c: mediatek: Add i2c compatible for MediaTek MT2712
Add i2c compatible for MT2712. Compare to MT8173 i2c controller,
internal divider of i2c source clock need to be configured for
MT2712 i2c speed calculation.

Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-04 00:53:26 +01:00
Wolfram Sang fddfa22a44 AT24 updates for 4.16 merge window
-----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEEFp3rbAvDxGAT0sefEacuoBRx13IFAlpM+BAACgkQEacuoBRx
 13KHtxAAj8uQ/ZEMz5vPQd4kQ3pn2a5Ts/yrAc8PPfk8SrBvMVk7KWNTRmbQgF2d
 EcL0Xs8AtiOYdSd1KmEQrkHtjJsJxRW27IsDGHJuoEc3aBrmAStgGvUUFROncZWU
 fHUm2Hy6Vw46Bx7HzxelmN5vjFHIZFdnx0sa6EfLL8Pui4VUVga7u9c8ezGL71MC
 TnXUCl6roWsrQhxoEWwX+HnzT0OI/Q+eQdvycWVyAOJDNga0F7+5KFhP6G1IOzsR
 QaUoowydRlSpot6dCRHeZ8+0aGtLXcZsMmQrg735ngdVT7ROZtY6dpXEpyn/KQHS
 ysFtaxJ8PPiC6PY0sXmztWBgZMLTph555Uqp3PSIlpuP5qFMqiTi8BoCv+UvXwA1
 QAyPd7QUrefLrhFb21v3RlDNdalMAU8NGKh8nEkaP664HJjw4TvRlWOcyxsmcsOI
 7szGsF/hsqQeaVrVsHQbF+sEy16u98VPIGA1k+KCtY0334vsMKOtfndXnS2OeR5l
 tJncNkfYD/0PeG479Wq4T42NOe6w90JmDKzWnLuDcY/zCJ7/AjJPp95AwyK/HPDc
 F5GcwC1WmcbcYkuKCG9c2nMxidpH8QZ5sei1TWey6lM4lAAHnQrXhohQw4zJcjst
 Q4ZRnXWGizSWOSTVQHVlmdUcPs/DlKPyDlcoTSEOD6JDhvl6AEY=
 =C2BD
 -----END PGP SIGNATURE-----

Merge tag 'at24-4.16-updates-for-wolfram' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-4.16

"AT24 updates for 4.16 merge window

The driver has been converted to using regmap instead of raw i2c and
smbus calls which shrank the code significantly.

Device tree binding document has been cleaned up. Device tree support in
the driver has been improved and we now support all at24 models as well
as two new DT properties (no-read-rollover and wp-gpios).

We no longer user unreadable magic values for driver data as the way it
was implemented caused problems for some EEPROM models - we switched to
regular structs.

Aside from that, there's a bunch of coding style fixes and minor
improvements all over the place."
2018-01-03 22:50:51 +01:00
Wolfram Sang 639136d2a7 Merge branch 'i2c-mux/for-next' of https://github.com/peda-r/i2c-mux into i2c/for-4.16
"A couple of patches this time. Just some more compatibles for the
pca954x driver and an error handling tweak for the reg driver."
2017-12-31 09:58:07 +01:00
Andy Shevchenko 017fc4f6f4 i2c: ismt: Use %pad specifier for dma_addr_t variables
...which takes care of proper format and size of the value.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-12-31 00:19:16 +01:00
Wolfram Sang 3e5f06bed7 i2c: algo-bit: init the bus to a known state
Ensure the bus is free when we register the adapter. Before the SCL/SDA
wires were in an unknown state. It used to work because sending a byte
has a retry mechanism which was triggered if the bus was initially in a
non-free state. But the graceful way to do it is to initialize
correctly.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-12-31 00:16:37 +01:00
Linus Walleij e535376537 i2c/ARM: davinci: Deep refactoring of I2C recovery
Alter the DaVinci GPIO recovery fetch to use descriptors
all the way down into the board files.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-12-31 00:09:39 +01:00
Tomasz Bachorski ac5b85de17 i2c: mux: reg: don't log an error for probe deferral
It's possible that i2c_mux_reg_probe_dt() could return -EPROBE_DEFER.
In that case, driver will request a probe deferral and an error
suggesting device tree parsing problem will be reported. This is
a pretty confusing information. Let's change the error handling,
so driver will be able to request probe deferral without logging
not related errors.

Signed-off-by: Tomasz Bachorski <tomasz.bachorski@nokia.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
2017-12-30 23:12:34 +01:00
Adrian Fiergolski 8f6d601689 i2c: mux: pca954x: add support for NXP PCA984x family
This patch extends the current i2c-mux-pca954x driver and adds support for
a newer PCA984x family of the I2C switches and multiplexers from NXP.

Signed-off-by: Adrian Fiergolski <adrian.fiergolski@cern.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
2017-12-30 23:12:34 +01:00
Linus Walleij 7d42762d8c i2c: imx: Include the right GPIO header
<linux/of_gpio.h> is not used in this file, by
<linux/gpio/consumer.h> is.

Someone is just lucky with their implicit includes.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-12-12 23:31:45 +01:00
Jean Delvare 45fd4470ba i2c: piix4: Fix port number check on release
The port number shift is still hard-coded to 1 while it now depends
on the hardware.

Thankfully 0 is always 0 no matter how you shift it, so this was a
bug without consequences.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 0fe16195f8 ("i2c: piix4: Fix SMBus port selection for AMD Family 17h chips")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-12-12 23:27:04 +01:00
Benjamin Gaignard 9c41e45218 i2c: stm32: Fix copyrights
Uniformize STMicroelectronics copyrights headers and add SPDX
identifier.

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Acked-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-12-12 23:16:04 +01:00
Wolfram Sang 4c3c9a9d0d i2c: imx: use proper GPIO directions for recovery
When converting to GPIOD, the GPIO directions of SCL/SDA have been
swapped. Fix it!

Fixes: ad36a27959 ("i2c: imx: switch to using gpiod for bus recovery gpios")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-12-07 12:04:12 +01:00
Arvind Yadav 04271ce960 i2c-cht-wc: constify platform_device_id
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-12-07 12:00:35 +01:00
Wolfram Sang adbd77b589 i2c: rcar: skip DMA if buffer is not safe
This HW is prone to races, so it needs to setup new messages in irq
context. That means we can't alloc bounce buffers if a message buffer is
not DMA safe. So, in that case, simply fall back to PIO.

Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-12-03 21:25:00 +01:00
Wolfram Sang fe23aa9a16 i2c: sh_mobile: use core helper to decide when to use DMA
This ensures that we fall back to PIO if the message length is too small
for DMA being useful. Otherwise, we use DMA. A bounce buffer might be
applied by the helper if the original message buffer is not DMA safe.

Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-12-03 21:24:59 +01:00
Wolfram Sang 8a77821e74 i2c: smbus: use DMA safe buffers for emulated SMBus transactions
For all block commands, try to allocate a DMA safe buffer and mark it
accordingly. Only use the stack, if the buffers cannot be allocated.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-12-03 21:24:52 +01:00
Wolfram Sang 8a91732b3b i2c: refactor i2c_master_{send_recv}
Those two functions are very similar, the only differences are that one
needs the I2C_M_RD flag for its message while the other one needs the
buffer casted to drop the const. Introduce a generic helper which allows
to specify the flags (also needed later for DMA safe variants of these
calls) and let the casting be done in the inlining functions which are
now calling the new helper function.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-12-03 21:22:29 +01:00
Wolfram Sang 978336d48d i2c: dev: mark RDWR buffers as DMA_SAFE
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-12-03 21:19:32 +01:00
Wolfram Sang e94bc5d18b i2c: add helpers to ease DMA handling
One helper checks if DMA is suitable and optionally creates a bounce
buffer, if not. The other function returns the bounce buffer and makes
sure the data is properly copied back to the message.

Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-12-03 20:47:44 +01:00
Wolfram Sang 14911c6f48 i2c: gpio: add fault injector
Add fault injection capabilities to the i2c-gpio driver. When connected
to another I2C bus, it can create unusual states which the other I2C bus
master driver needs to handle. Only for debugging!

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
2017-12-03 20:33:29 +01:00
Wolfram Sang f15fc9b122 ARM: pxa: move header file out of I2C realm
include/linux/i2c is to be deprecated. Move this platform_data to the
proper platform_data dir.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
2017-11-28 22:49:30 +01:00
Phil Reid 4d67c2e7f6 i2c: designware: fix building driver as module
The designware core and platform are built as separate modules.
Export i2c_dw_prepare_clk() so it can be used by the platform
driver.

Fixes: a34a0b6da2 ("i2c: designware: move i2c_dw_plat_prepare_clk to common")
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-28 10:44:19 +01:00
Phil Reid 10c9ef045a i2c: core: fix compile issue related to incorrect gpio header
The correct header to include for the gpiod interface is
<linux/gpio/consumer.h>.

Fixes: 3991c5c80b ("i2c: Switch to using gpiod interface for gpio bus recovery")
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-28 10:44:00 +01:00
Colin Ian King 66a7c84d67 i2c: i2c-boardinfo: fix memory leaks on devinfo
Currently when an error occurs devinfo is still allocated but is
unused when the error exit paths break out of the for-loop. Fix
this by kfree'ing devinfo to avoid the leak.

Detected by CoverityScan, CID#1416590 ("Resource Leak")

Fixes: 4124c4eba4 ("i2c: allow attaching IRQ resources to i2c_board_info")
Fixes: 0daaf99d84 ("i2c: copy device properties when using i2c_register_board_info()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27 19:14:29 +01:00
Hans de Goede 6e0c9507bf i2c: i801: Fix Failed to allocate irq -2147483648 error
On Apollo Lake devices the BIOS does not set up IRQ routing for the i801
SMBUS controller IRQ, so we end up with dev->irq set to IRQ_NOTCONNECTED.

Detect this and do not try to use the irq in this case silencing:
i801_smbus 0000:00:1f.1: Failed to allocate irq -2147483648: -107

Cc: stable@vger.kernel.org
BugLink: https://communities.intel.com/thread/114759
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27 19:11:27 +01:00
Wolfram Sang 4ed152c4da i2c: sh_mobile: make sure to not accidently trigger STOP
The datasheet was a bit vague, but after consultation with HW designers,
we came to the conclusion that we should set the SCP bit always when
dealing only with the ICE bit. A set SCP bit is ignored, and thus fine,
a cleared one may trigger STOP on the bus.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27 18:53:34 +01:00
Wolfram Sang a4fde7e5c9 i2c: sh_mobile: send STOP according to datasheet
We initiate STOP (or REP_START) on the second last WAIT interrupt
currently. This works fine but is not according to the datasheet which
says to do it on the last WAIT interrupt. This also simplifies the code
quite a lot, so let's do it.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27 18:53:29 +01:00
Wolfram Sang 2967f9ca8b i2c: sh_mobile: avoid unnecessary register read
There is no data when the first WAIT interrupt arrives. No need to read
something then.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27 18:53:23 +01:00
Wolfram Sang 91701ae85d i2c: sh_mobile: let RuntimePM do the clock handling
No need to do it manually.

Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27 18:53:18 +01:00
Wolfram Sang a4d16493be i2c: sh_mobile: shorten exit of xfer routine
We can use the ternary operator for easier reading.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27 18:53:12 +01:00
Wolfram Sang 832a522a3e i2c: sh_mobile: use direct writes when accessing ICE bit
ICE bit is for resetting the module. Other bits don't matter then, so we
don't need to use the iic_set_clr() function but can use iic_wr().

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27 18:53:07 +01:00
Wolfram Sang 91a5e63e3f i2c: sh_mobile: manually "inline" two short functions
Those two functions are very short and only called once. The code
becomes easier to understand if the code is directly put into the main
xfer function.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27 18:53:02 +01:00
Wolfram Sang 3f3a513985 i2c: sh_mobile: remove redundant deinitialization
No need to clear the interrupt registers because right after that we
disable the IP core which will reload registers with their initial
values anyhow.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27 18:52:56 +01:00
Wolfram Sang f289800af1 i2c: sh_mobile: remove redundant initialization
Following the documentation, we initialize the HW before each START in
start_ch(). No need to do the same in activate_ch().

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27 18:52:51 +01:00
Phil Reid e1eb7d28c0 i2c: remove legacy integer scl/sda gpio for recovery
Remove all reference to code related to using integer based ids for
scl/sda gpio for bus recovery. All in tree drivers are now using the
gpio descriptors to specific the required gpios.

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27 18:40:01 +01:00
Phil Reid cd2428c368 i2c: davinci: switch to using gpiod for bus recovery gpios
Change the driver to use the gpio descriptors for the bus recovery
information instead of the deprecated integer interface.

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27 18:39:51 +01:00
Phil Reid ad36a27959 i2c: imx: switch to using gpiod for bus recovery gpios
Change the driver to use the gpio descriptors for the bus recovery
information instead of the deprecated integer interface.

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27 18:39:45 +01:00
Tim Sander ca382f5b38 i2c: designware: add i2c gpio recovery option
This patch contains much input from Phil Reid and has been tested
on Intel/Altera Cyclone V SOC Hardware with Altera GPIO's for the
SCL and SDA GPIO's.

Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tim Sander <tim@krieglstein.org>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27 18:39:38 +01:00
Phil Reid 0326f9f801 i2c: designware: rename i2c_dw_plat_prepare_clk to i2c_dw_prepare_clk
For consistency with the rest of the file rename function and parameter to
be consistent with the reset of the common file.

Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27 18:39:30 +01:00
Phil Reid a34a0b6da2 i2c: designware: move i2c_dw_plat_prepare_clk to common
Move the i2c_dw_plat_prepare_clk funciton to common file in preparation
for its use also by the master driver.

Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27 18:39:22 +01:00
Phil Reid 3991c5c80b i2c: Switch to using gpiod interface for gpio bus recovery
Currently the i2c gpio recovery code uses gpio integer interface
instead of the gpiod. This change switch the core code to use
the gpiod while still retaining compatibility with the gpio integer
interface. This will allow individual driver to be updated and tested
individual to switch to using the gpiod interface.

Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27 18:39:13 +01:00
Jarkko Nikula 43df43e6ba i2c: designware: Don't set SCL timings and speed mode when in slave mode
According to data sheet SCL timing parameters and DW_IC_CON SPEED mode
bits are not used when operating in slave mode.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Luis Oliveira <lolivei@synopsys.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27 18:30:13 +01:00
Linus Torvalds 93f30c73ec Merge branch 'misc.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull compat and uaccess updates from Al Viro:

 - {get,put}_compat_sigset() series

 - assorted compat ioctl stuff

 - more set_fs() elimination

 - a few more timespec64 conversions

 - several removals of pointless access_ok() in places where it was
   followed only by non-__ variants of primitives

* 'misc.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (24 commits)
  coredump: call do_unlinkat directly instead of sys_unlink
  fs: expose do_unlinkat for built-in callers
  ext4: take handling of EXT4_IOC_GROUP_ADD into a helper, get rid of set_fs()
  ipmi: get rid of pointless access_ok()
  pi433: sanitize ioctl
  cxlflash: get rid of pointless access_ok()
  mtdchar: get rid of pointless access_ok()
  r128: switch compat ioctls to drm_ioctl_kernel()
  selection: get rid of field-by-field copyin
  VT_RESIZEX: get rid of field-by-field copyin
  i2c compat ioctls: move to ->compat_ioctl()
  sched_rr_get_interval(): move compat to native, get rid of set_fs()
  mips: switch to {get,put}_compat_sigset()
  sparc: switch to {get,put}_compat_sigset()
  s390: switch to {get,put}_compat_sigset()
  ppc: switch to {get,put}_compat_sigset()
  parisc: switch to {get,put}_compat_sigset()
  get_compat_sigset()
  get rid of {get,put}_compat_itimerspec()
  io_getevents: Use timespec64 to represent timeouts
  ...
2017-11-17 11:54:55 -08:00
Linus Torvalds 4008e6a9bc Merge branch 'i2c/for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
 "This contains two bigger than usual tree-wide changes this time. They
  all have proper acks, caused no merge conflicts in linux-next where
  they have been for a while. They are namely:

   - to-gpiod conversion of the i2c-gpio driver and its users (touching
     arch/* and drivers/mfd/*)

   - adding a sbs-manager based on I2C core updates to SMBus alerts
     (touching drivers/power/*)

  Other notable changes:

   - i2c_boardinfo can now carry a dev_name to be used when the device
     is created. This is because some devices in ACPI world need fixed
     names to find the regulators.

   - the designware driver got a long discussed overhaul of its PM
     handling. img-scb and davinci got PM support, too.

   - at24 driver has way better OF support. And it has a new maintainer.
     Thanks Bartosz for stepping up!

  The rest is regular driver updates and fixes"

* 'i2c/for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (55 commits)
  ARM: sa1100: simpad: Correct I2C GPIO offsets
  i2c: aspeed: Deassert reset in probe
  eeprom: at24: Add OF device ID table
  MAINTAINERS: new maintainer for AT24 driver
  i2c: nuc900: remove platform_data, too
  i2c: thunderx: Remove duplicate NULL check
  i2c: taos-evm: Remove duplicate NULL check
  i2c: Make i2c_unregister_device() NULL-aware
  i2c: xgene-slimpro: Support v2
  i2c: mpc: remove useless variable initialization
  i2c: omap: Trigger bus recovery in lockup case
  i2c: gpio: Add support for named gpios in DT
  dt-bindings: i2c: i2c-gpio: Add support for named gpios
  i2c: gpio: Local vars in probe
  i2c: gpio: Augment all boardfiles to use open drain
  i2c: gpio: Enforce open drain through gpiolib
  gpio: Make it possible for consumers to enforce open drain
  i2c: gpio: Convert to use descriptors
  power: supply: sbs-message: fix some code style issues
  power: supply: sbs-battery: remove unchecked return var
  ...
2017-11-14 17:52:21 -08:00
Joel Stanley edd20e95bc i2c: aspeed: Deassert reset in probe
In order to use i2c from a cold boot, the i2c peripheral must be taken
out of reset. We request a shared reset controller each time a bus
driver is loaded, as the reset is shared between the 14 i2c buses.

On remove the reset is asserted, which only touches the hardware once
the last i2c bus is removed.

The reset is required as the I2C buses will not work without releasing
the reset. Previously the driver only worked with out of tree hacks
that released this reset before the driver was loaded. Update the
device tree bindings to reflect this.

Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-06 19:15:31 +01:00