qemu-e2k/hw/acpi/piix4.c

691 lines
22 KiB
C
Raw Normal View History

/*
* ACPI implementation
*
* Copyright (c) 2006 Fabrice Bellard
*
* This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU Lesser General Public
* License version 2 as published by the Free Software Foundation.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* Lesser General Public License for more details.
*
* You should have received a copy of the GNU Lesser General Public
* License along with this library; if not, see <http://www.gnu.org/licenses/>
*
* Contributions after 2012-01-13 are licensed under the terms of the
* GNU GPL, version 2 or (at your option) any later version.
*/
#include "qemu/osdep.h"
#include "hw/i386/pc.h"
#include "hw/southbridge/piix.h"
#include "hw/irq.h"
#include "hw/isa/apm.h"
#include "hw/i2c/pm_smbus.h"
#include "hw/pci/pci.h"
#include "hw/qdev-properties.h"
#include "hw/acpi/acpi.h"
#include "sysemu/runstate.h"
#include "sysemu/sysemu.h"
2016-03-14 09:01:28 +01:00
#include "qapi/error.h"
#include "qemu/range.h"
#include "exec/address-spaces.h"
#include "hw/acpi/pcihp.h"
#include "hw/acpi/cpu_hotplug.h"
#include "hw/acpi/cpu.h"
#include "hw/hotplug.h"
#include "hw/mem/pc-dimm.h"
#include "hw/acpi/memory_hotplug.h"
#include "hw/acpi/acpi_dev_interface.h"
#include "hw/xen/xen.h"
#include "migration/vmstate.h"
#include "hw/core/cpu.h"
#include "trace.h"
#define GPE_BASE 0xafe0
#define GPE_LEN 4
struct pci_status {
acpi_piix4: Fix PCI hotplug race As Michael Tsirkin demonstrated, current PCI hotplug is vulnerable to a few races. The first is a race with other hotplug operations because we clear the up & down registers at each event. If a new event comes before the last is processed, up/down is cleared and the event is lost. To fix this for the down register, we create a life cycle for the event request that starts with the hot unplug request in piix4_device_hotplug() and ends when the device is ejected. This allows us to mask and clear individual bits, preserving them against races. For the up register, we have no clear end point for when the event is finished. We could modify the BIOS to acknowledge the bit and clear it, but this creates BIOS compatibiliy issues without offering a complete solution. Instead we note that gratuitous ACPI device checks are not harmful, which allows us to issue a device check for every slot. We know which slots are present and we know which slots are hotpluggable, so we can easily reduce this to a more manageable set for the guest. The other race Michael noted was that an unplug request followed by reset may also lose the eject notification, which may also result in the eject request being lost which a subsequent add or remove. Once we're in reset, the device is unused and we can flush the queue of device removals ourselves. Previously if a device_del was issued to a guest without ACPI PCI hotplug support, it was necessary to shutdown the guest to recover the device. With this, a guest reboot is sufficient. Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2012-04-05 19:07:15 +02:00
uint32_t up; /* deprecated, maintained for migration compatibility */
uint32_t down;
};
typedef struct PIIX4PMState {
/*< private >*/
PCIDevice parent_obj;
/*< public >*/
MemoryRegion io;
uint32_t io_base;
MemoryRegion io_gpe;
ACPIREGS ar;
APMState apm;
PMSMBus smb;
uint32_t smb_io_base;
qemu_irq irq;
qemu_irq smi_irq;
int smm_enabled;
report serial devices created with -device in the PIIX4 config space Serial and parallel devices created with -device are not reported in the PIIX4 configuration space, and are hence not picked up by the DSDT. This upsets Windows, which hides them altogether from the guest. To avoid this, check at the end of machine initialization whether the corresponding I/O ports have been registered. The new function in ioport.c does this; this also requires a tweak to isa_unassign_ioport. I left the comment in piix4_pm_initfn since the registers I moved do seem to match the 82371AB datasheet. There are some quirks though. We are setting this bit: "Device 8 EIO Enable (EIO_EN_DEV8)—R/W. 1=Enable PCI access to the device 8 enabled I/O ranges to be claimed by PIIX4 and forwarded to the ISA/EIO bus. 0=Disable. The LPT_MON_EN must be set to enable the decode." but not LPT_MON_EN (bit 18 at 50h): LPT Port Enable (LPT_MON_EN)—R/W. 1=Enable accesses to parallel port address range (LPT_DEC_SEL) to generate a device 8 (parallel port) decode event. 0=Disable. We're also setting the LPT_DEC_SEL field (that's the 0x60 written to 63h) to 11, which means reserved, rather than to 01 (378h-37Fh). Likewise we're not setting SA_MON_EN, SB_MON_EN (respectively bit 14 and bit 16 at address 50h) for the serial ports. However, we're setting COMA_DEC_SEL and COMB_DEC_SEL correctly, unlike the corresponding register for the parallel port. All these fields are left as they are, since they are probably only meant to be used in the DSDT. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2011-07-15 17:10:15 +02:00
Notifier machine_ready;
Notifier powerdown_notifier;
AcpiPciHpState acpi_pci_hotplug;
bool use_acpi_pci_hotplug;
uint8_t disable_s3;
uint8_t disable_s4;
uint8_t s4_val;
bool cpu_hotplug_legacy;
AcpiCpuHotplug gpe_cpu;
CPUHotplugState cpuhp_state;
MemHotplugState acpi_memory_hotplug;
} PIIX4PMState;
#define PIIX4_PM(obj) \
OBJECT_CHECK(PIIX4PMState, (obj), TYPE_PIIX4_PM)
static void piix4_acpi_system_hot_add_init(MemoryRegion *parent,
PCIBus *bus, PIIX4PMState *s);
#define ACPI_ENABLE 0xf1
#define ACPI_DISABLE 0xf0
static void pm_tmr_timer(ACPIREGS *ar)
{
PIIX4PMState *s = container_of(ar, PIIX4PMState, ar);
acpi_update_sci(&s->ar, s->irq);
}
static void apm_ctrl_changed(uint32_t val, void *arg)
{
PIIX4PMState *s = arg;
PCIDevice *d = PCI_DEVICE(s);
/* ACPI specs 3.0, 4.7.2.5 */
acpi_pm1_cnt_update(&s->ar, val == ACPI_ENABLE, val == ACPI_DISABLE);
if (val == ACPI_ENABLE || val == ACPI_DISABLE) {
return;
}
if (d->config[0x5b] & (1 << 1)) {
if (s->smi_irq) {
qemu_irq_raise(s->smi_irq);
}
}
}
static void pm_io_space_update(PIIX4PMState *s)
{
PCIDevice *d = PCI_DEVICE(s);
s->io_base = le32_to_cpu(*(uint32_t *)(d->config + 0x40));
s->io_base &= 0xffc0;
memory_region_transaction_begin();
memory_region_set_enabled(&s->io, d->config[0x80] & 1);
memory_region_set_address(&s->io, s->io_base);
memory_region_transaction_commit();
}
static void smbus_io_space_update(PIIX4PMState *s)
{
PCIDevice *d = PCI_DEVICE(s);
s->smb_io_base = le32_to_cpu(*(uint32_t *)(d->config + 0x90));
s->smb_io_base &= 0xffc0;
memory_region_transaction_begin();
memory_region_set_enabled(&s->smb.io, d->config[0xd2] & 1);
memory_region_set_address(&s->smb.io, s->smb_io_base);
memory_region_transaction_commit();
}
static void pm_write_config(PCIDevice *d,
uint32_t address, uint32_t val, int len)
{
pci_default_write_config(d, address, val, len);
if (range_covers_byte(address, len, 0x80) ||
ranges_overlap(address, len, 0x40, 4)) {
pm_io_space_update((PIIX4PMState *)d);
}
if (range_covers_byte(address, len, 0xd2) ||
ranges_overlap(address, len, 0x90, 4)) {
smbus_io_space_update((PIIX4PMState *)d);
}
}
static int vmstate_acpi_post_load(void *opaque, int version_id)
{
PIIX4PMState *s = opaque;
pm_io_space_update(s);
smbus_io_space_update(s);
return 0;
}
#define VMSTATE_GPE_ARRAY(_field, _state) \
{ \
.name = (stringify(_field)), \
.version_id = 0, \
.info = &vmstate_info_uint16, \
.size = sizeof(uint16_t), \
.flags = VMS_SINGLE | VMS_POINTER, \
.offset = vmstate_offset_pointer(_state, _field, uint8_t), \
}
static const VMStateDescription vmstate_gpe = {
.name = "gpe",
.version_id = 1,
.minimum_version_id = 1,
.fields = (VMStateField[]) {
VMSTATE_GPE_ARRAY(sts, ACPIGPE),
VMSTATE_GPE_ARRAY(en, ACPIGPE),
VMSTATE_END_OF_LIST()
}
};
static const VMStateDescription vmstate_pci_status = {
.name = "pci_status",
.version_id = 1,
.minimum_version_id = 1,
.fields = (VMStateField[]) {
VMSTATE_UINT32(up, struct AcpiPciHpPciStatus),
VMSTATE_UINT32(down, struct AcpiPciHpPciStatus),
VMSTATE_END_OF_LIST()
}
};
static bool vmstate_test_use_acpi_pci_hotplug(void *opaque, int version_id)
{
PIIX4PMState *s = opaque;
return s->use_acpi_pci_hotplug;
}
static bool vmstate_test_no_use_acpi_pci_hotplug(void *opaque, int version_id)
{
PIIX4PMState *s = opaque;
return !s->use_acpi_pci_hotplug;
}
static bool vmstate_test_use_memhp(void *opaque)
{
PIIX4PMState *s = opaque;
return s->acpi_memory_hotplug.is_enabled;
}
static const VMStateDescription vmstate_memhp_state = {
.name = "piix4_pm/memhp",
.version_id = 1,
.minimum_version_id = 1,
.minimum_version_id_old = 1,
.needed = vmstate_test_use_memhp,
.fields = (VMStateField[]) {
VMSTATE_MEMORY_HOTPLUG(acpi_memory_hotplug, PIIX4PMState),
VMSTATE_END_OF_LIST()
}
};
static bool vmstate_test_use_cpuhp(void *opaque)
{
PIIX4PMState *s = opaque;
return !s->cpu_hotplug_legacy;
}
static int vmstate_cpuhp_pre_load(void *opaque)
{
Object *obj = OBJECT(opaque);
object_property_set_bool(obj, false, "cpu-hotplug-legacy", &error_abort);
return 0;
}
static const VMStateDescription vmstate_cpuhp_state = {
.name = "piix4_pm/cpuhp",
.version_id = 1,
.minimum_version_id = 1,
.minimum_version_id_old = 1,
.needed = vmstate_test_use_cpuhp,
.pre_load = vmstate_cpuhp_pre_load,
.fields = (VMStateField[]) {
VMSTATE_CPU_HOTPLUG(cpuhp_state, PIIX4PMState),
VMSTATE_END_OF_LIST()
}
};
static bool piix4_vmstate_need_smbus(void *opaque, int version_id)
{
return pm_smbus_vmstate_needed();
}
/* qemu-kvm 1.2 uses version 3 but advertised as 2
* To support incoming qemu-kvm 1.2 migration, change version_id
* and minimum_version_id to 2 below (which breaks migration from
* qemu 1.2).
*
*/
static const VMStateDescription vmstate_acpi = {
.name = "piix4_pm",
.version_id = 3,
.minimum_version_id = 3,
.post_load = vmstate_acpi_post_load,
.fields = (VMStateField[]) {
VMSTATE_PCI_DEVICE(parent_obj, PIIX4PMState),
VMSTATE_UINT16(ar.pm1.evt.sts, PIIX4PMState),
VMSTATE_UINT16(ar.pm1.evt.en, PIIX4PMState),
VMSTATE_UINT16(ar.pm1.cnt.cnt, PIIX4PMState),
VMSTATE_STRUCT(apm, PIIX4PMState, 0, vmstate_apm, APMState),
VMSTATE_STRUCT_TEST(smb, PIIX4PMState, piix4_vmstate_need_smbus, 3,
pmsmb_vmstate, PMSMBus),
VMSTATE_TIMER_PTR(ar.tmr.timer, PIIX4PMState),
VMSTATE_INT64(ar.tmr.overflow_time, PIIX4PMState),
VMSTATE_STRUCT(ar.gpe, PIIX4PMState, 2, vmstate_gpe, ACPIGPE),
VMSTATE_STRUCT_TEST(
acpi_pci_hotplug.acpi_pcihp_pci_status[ACPI_PCIHP_BSEL_DEFAULT],
PIIX4PMState,
vmstate_test_no_use_acpi_pci_hotplug,
2, vmstate_pci_status,
struct AcpiPciHpPciStatus),
VMSTATE_PCI_HOTPLUG(acpi_pci_hotplug, PIIX4PMState,
vmstate_test_use_acpi_pci_hotplug),
VMSTATE_END_OF_LIST()
},
.subsections = (const VMStateDescription*[]) {
&vmstate_memhp_state,
&vmstate_cpuhp_state,
NULL
}
};
static void piix4_pm_reset(DeviceState *dev)
{
PIIX4PMState *s = PIIX4_PM(dev);
PCIDevice *d = PCI_DEVICE(s);
uint8_t *pci_conf = d->config;
pci_conf[0x58] = 0;
pci_conf[0x59] = 0;
pci_conf[0x5a] = 0;
pci_conf[0x5b] = 0;
pci_conf[0x40] = 0x01; /* PM io base read only bit */
pci_conf[0x80] = 0;
if (!s->smm_enabled) {
/* Mark SMM as already inited (until KVM supports SMM). */
pci_conf[0x5B] = 0x02;
}
pm_io_space_update(s);
acpi_pcihp_reset(&s->acpi_pci_hotplug);
}
static void piix4_pm_powerdown_req(Notifier *n, void *opaque)
{
PIIX4PMState *s = container_of(n, PIIX4PMState, powerdown_notifier);
assert(s != NULL);
acpi_pm1_evt_power_down(&s->ar);
}
static void piix4_device_pre_plug_cb(HotplugHandler *hotplug_dev,
DeviceState *dev, Error **errp)
{
PIIX4PMState *s = PIIX4_PM(hotplug_dev);
if (object_dynamic_cast(OBJECT(dev), TYPE_PCI_DEVICE)) {
acpi_pcihp_device_pre_plug_cb(hotplug_dev, dev, errp);
} else if (object_dynamic_cast(OBJECT(dev), TYPE_PC_DIMM)) {
if (!s->acpi_memory_hotplug.is_enabled) {
error_setg(errp,
"memory hotplug is not enabled: %s.memory-hotplug-support "
"is not set", object_get_typename(OBJECT(s)));
}
} else if (
!object_dynamic_cast(OBJECT(dev), TYPE_CPU)) {
error_setg(errp, "acpi: device pre plug request for not supported"
" device type: %s", object_get_typename(OBJECT(dev)));
}
}
static void piix4_device_plug_cb(HotplugHandler *hotplug_dev,
DeviceState *dev, Error **errp)
{
PIIX4PMState *s = PIIX4_PM(hotplug_dev);
if (object_dynamic_cast(OBJECT(dev), TYPE_PC_DIMM)) {
if (object_dynamic_cast(OBJECT(dev), TYPE_NVDIMM)) {
nvdimm_acpi_plug_cb(hotplug_dev, dev);
} else {
acpi_memory_plug_cb(hotplug_dev, &s->acpi_memory_hotplug,
dev, errp);
}
} else if (object_dynamic_cast(OBJECT(dev), TYPE_PCI_DEVICE)) {
acpi_pcihp_device_plug_cb(hotplug_dev, &s->acpi_pci_hotplug, dev, errp);
} else if (object_dynamic_cast(OBJECT(dev), TYPE_CPU)) {
if (s->cpu_hotplug_legacy) {
legacy_acpi_cpu_plug_cb(hotplug_dev, &s->gpe_cpu, dev, errp);
} else {
acpi_cpu_plug_cb(hotplug_dev, &s->cpuhp_state, dev, errp);
}
} else {
g_assert_not_reached();
}
}
static void piix4_device_unplug_request_cb(HotplugHandler *hotplug_dev,
DeviceState *dev, Error **errp)
{
PIIX4PMState *s = PIIX4_PM(hotplug_dev);
if (s->acpi_memory_hotplug.is_enabled &&
object_dynamic_cast(OBJECT(dev), TYPE_PC_DIMM)) {
acpi_memory_unplug_request_cb(hotplug_dev, &s->acpi_memory_hotplug,
dev, errp);
} else if (object_dynamic_cast(OBJECT(dev), TYPE_PCI_DEVICE)) {
acpi_pcihp_device_unplug_request_cb(hotplug_dev, &s->acpi_pci_hotplug,
dev, errp);
} else if (object_dynamic_cast(OBJECT(dev), TYPE_CPU) &&
!s->cpu_hotplug_legacy) {
acpi_cpu_unplug_request_cb(hotplug_dev, &s->cpuhp_state, dev, errp);
} else {
error_setg(errp, "acpi: device unplug request for not supported device"
" type: %s", object_get_typename(OBJECT(dev)));
}
}
static void piix4_device_unplug_cb(HotplugHandler *hotplug_dev,
DeviceState *dev, Error **errp)
{
PIIX4PMState *s = PIIX4_PM(hotplug_dev);
if (s->acpi_memory_hotplug.is_enabled &&
object_dynamic_cast(OBJECT(dev), TYPE_PC_DIMM)) {
acpi_memory_unplug_cb(&s->acpi_memory_hotplug, dev, errp);
} else if (object_dynamic_cast(OBJECT(dev), TYPE_PCI_DEVICE)) {
acpi_pcihp_device_unplug_cb(hotplug_dev, &s->acpi_pci_hotplug, dev,
errp);
} else if (object_dynamic_cast(OBJECT(dev), TYPE_CPU) &&
!s->cpu_hotplug_legacy) {
acpi_cpu_unplug_cb(&s->cpuhp_state, dev, errp);
} else {
error_setg(errp, "acpi: device unplug for not supported device"
" type: %s", object_get_typename(OBJECT(dev)));
}
}
static void piix4_pm_machine_ready(Notifier *n, void *opaque)
report serial devices created with -device in the PIIX4 config space Serial and parallel devices created with -device are not reported in the PIIX4 configuration space, and are hence not picked up by the DSDT. This upsets Windows, which hides them altogether from the guest. To avoid this, check at the end of machine initialization whether the corresponding I/O ports have been registered. The new function in ioport.c does this; this also requires a tweak to isa_unassign_ioport. I left the comment in piix4_pm_initfn since the registers I moved do seem to match the 82371AB datasheet. There are some quirks though. We are setting this bit: "Device 8 EIO Enable (EIO_EN_DEV8)—R/W. 1=Enable PCI access to the device 8 enabled I/O ranges to be claimed by PIIX4 and forwarded to the ISA/EIO bus. 0=Disable. The LPT_MON_EN must be set to enable the decode." but not LPT_MON_EN (bit 18 at 50h): LPT Port Enable (LPT_MON_EN)—R/W. 1=Enable accesses to parallel port address range (LPT_DEC_SEL) to generate a device 8 (parallel port) decode event. 0=Disable. We're also setting the LPT_DEC_SEL field (that's the 0x60 written to 63h) to 11, which means reserved, rather than to 01 (378h-37Fh). Likewise we're not setting SA_MON_EN, SB_MON_EN (respectively bit 14 and bit 16 at address 50h) for the serial ports. However, we're setting COMA_DEC_SEL and COMB_DEC_SEL correctly, unlike the corresponding register for the parallel port. All these fields are left as they are, since they are probably only meant to be used in the DSDT. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2011-07-15 17:10:15 +02:00
{
PIIX4PMState *s = container_of(n, PIIX4PMState, machine_ready);
PCIDevice *d = PCI_DEVICE(s);
MemoryRegion *io_as = pci_address_space_io(d);
report serial devices created with -device in the PIIX4 config space Serial and parallel devices created with -device are not reported in the PIIX4 configuration space, and are hence not picked up by the DSDT. This upsets Windows, which hides them altogether from the guest. To avoid this, check at the end of machine initialization whether the corresponding I/O ports have been registered. The new function in ioport.c does this; this also requires a tweak to isa_unassign_ioport. I left the comment in piix4_pm_initfn since the registers I moved do seem to match the 82371AB datasheet. There are some quirks though. We are setting this bit: "Device 8 EIO Enable (EIO_EN_DEV8)—R/W. 1=Enable PCI access to the device 8 enabled I/O ranges to be claimed by PIIX4 and forwarded to the ISA/EIO bus. 0=Disable. The LPT_MON_EN must be set to enable the decode." but not LPT_MON_EN (bit 18 at 50h): LPT Port Enable (LPT_MON_EN)—R/W. 1=Enable accesses to parallel port address range (LPT_DEC_SEL) to generate a device 8 (parallel port) decode event. 0=Disable. We're also setting the LPT_DEC_SEL field (that's the 0x60 written to 63h) to 11, which means reserved, rather than to 01 (378h-37Fh). Likewise we're not setting SA_MON_EN, SB_MON_EN (respectively bit 14 and bit 16 at address 50h) for the serial ports. However, we're setting COMA_DEC_SEL and COMB_DEC_SEL correctly, unlike the corresponding register for the parallel port. All these fields are left as they are, since they are probably only meant to be used in the DSDT. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2011-07-15 17:10:15 +02:00
uint8_t *pci_conf;
pci_conf = d->config;
pci_conf[0x5f] = 0x10 |
(memory_region_present(io_as, 0x378) ? 0x80 : 0);
report serial devices created with -device in the PIIX4 config space Serial and parallel devices created with -device are not reported in the PIIX4 configuration space, and are hence not picked up by the DSDT. This upsets Windows, which hides them altogether from the guest. To avoid this, check at the end of machine initialization whether the corresponding I/O ports have been registered. The new function in ioport.c does this; this also requires a tweak to isa_unassign_ioport. I left the comment in piix4_pm_initfn since the registers I moved do seem to match the 82371AB datasheet. There are some quirks though. We are setting this bit: "Device 8 EIO Enable (EIO_EN_DEV8)—R/W. 1=Enable PCI access to the device 8 enabled I/O ranges to be claimed by PIIX4 and forwarded to the ISA/EIO bus. 0=Disable. The LPT_MON_EN must be set to enable the decode." but not LPT_MON_EN (bit 18 at 50h): LPT Port Enable (LPT_MON_EN)—R/W. 1=Enable accesses to parallel port address range (LPT_DEC_SEL) to generate a device 8 (parallel port) decode event. 0=Disable. We're also setting the LPT_DEC_SEL field (that's the 0x60 written to 63h) to 11, which means reserved, rather than to 01 (378h-37Fh). Likewise we're not setting SA_MON_EN, SB_MON_EN (respectively bit 14 and bit 16 at address 50h) for the serial ports. However, we're setting COMA_DEC_SEL and COMB_DEC_SEL correctly, unlike the corresponding register for the parallel port. All these fields are left as they are, since they are probably only meant to be used in the DSDT. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2011-07-15 17:10:15 +02:00
pci_conf[0x63] = 0x60;
pci_conf[0x67] = (memory_region_present(io_as, 0x3f8) ? 0x08 : 0) |
(memory_region_present(io_as, 0x2f8) ? 0x90 : 0);
report serial devices created with -device in the PIIX4 config space Serial and parallel devices created with -device are not reported in the PIIX4 configuration space, and are hence not picked up by the DSDT. This upsets Windows, which hides them altogether from the guest. To avoid this, check at the end of machine initialization whether the corresponding I/O ports have been registered. The new function in ioport.c does this; this also requires a tweak to isa_unassign_ioport. I left the comment in piix4_pm_initfn since the registers I moved do seem to match the 82371AB datasheet. There are some quirks though. We are setting this bit: "Device 8 EIO Enable (EIO_EN_DEV8)—R/W. 1=Enable PCI access to the device 8 enabled I/O ranges to be claimed by PIIX4 and forwarded to the ISA/EIO bus. 0=Disable. The LPT_MON_EN must be set to enable the decode." but not LPT_MON_EN (bit 18 at 50h): LPT Port Enable (LPT_MON_EN)—R/W. 1=Enable accesses to parallel port address range (LPT_DEC_SEL) to generate a device 8 (parallel port) decode event. 0=Disable. We're also setting the LPT_DEC_SEL field (that's the 0x60 written to 63h) to 11, which means reserved, rather than to 01 (378h-37Fh). Likewise we're not setting SA_MON_EN, SB_MON_EN (respectively bit 14 and bit 16 at address 50h) for the serial ports. However, we're setting COMA_DEC_SEL and COMB_DEC_SEL correctly, unlike the corresponding register for the parallel port. All these fields are left as they are, since they are probably only meant to be used in the DSDT. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2011-07-15 17:10:15 +02:00
}
static void piix4_pm_add_propeties(PIIX4PMState *s)
{
static const uint8_t acpi_enable_cmd = ACPI_ENABLE;
static const uint8_t acpi_disable_cmd = ACPI_DISABLE;
static const uint32_t gpe0_blk = GPE_BASE;
static const uint32_t gpe0_blk_len = GPE_LEN;
static const uint16_t sci_int = 9;
object_property_add_uint8_ptr(OBJECT(s), ACPI_PM_PROP_ACPI_ENABLE_CMD,
&acpi_enable_cmd, NULL);
object_property_add_uint8_ptr(OBJECT(s), ACPI_PM_PROP_ACPI_DISABLE_CMD,
&acpi_disable_cmd, NULL);
object_property_add_uint32_ptr(OBJECT(s), ACPI_PM_PROP_GPE0_BLK,
&gpe0_blk, NULL);
object_property_add_uint32_ptr(OBJECT(s), ACPI_PM_PROP_GPE0_BLK_LEN,
&gpe0_blk_len, NULL);
object_property_add_uint16_ptr(OBJECT(s), ACPI_PM_PROP_SCI_INT,
&sci_int, NULL);
object_property_add_uint32_ptr(OBJECT(s), ACPI_PM_PROP_PM_IO_BASE,
&s->io_base, NULL);
}
static void piix4_pm_realize(PCIDevice *dev, Error **errp)
{
PIIX4PMState *s = PIIX4_PM(dev);
uint8_t *pci_conf;
pci_conf = dev->config;
pci_conf[0x06] = 0x80;
pci_conf[0x07] = 0x02;
pci_conf[0x09] = 0x00;
pci_conf[0x3d] = 0x01; // interrupt pin 1
/* APM */
apm_init(dev, &s->apm, apm_ctrl_changed, s);
if (!s->smm_enabled) {
/* Mark SMM as already inited to prevent SMM from running. KVM does not
* support SMM mode. */
pci_conf[0x5B] = 0x02;
}
/* XXX: which specification is used ? The i82731AB has different
mappings */
pci_conf[0x90] = s->smb_io_base | 1;
pci_conf[0x91] = s->smb_io_base >> 8;
pci_conf[0xd2] = 0x09;
pm_smbus_init(DEVICE(dev), &s->smb, true);
memory_region_set_enabled(&s->smb.io, pci_conf[0xd2] & 1);
memory_region_add_subregion(pci_address_space_io(dev),
s->smb_io_base, &s->smb.io);
memory_region_init(&s->io, OBJECT(s), "piix4-pm", 64);
memory_region_set_enabled(&s->io, false);
memory_region_add_subregion(pci_address_space_io(dev),
0, &s->io);
acpi_pm_tmr_init(&s->ar, pm_tmr_timer, &s->io);
acpi_pm1_evt_init(&s->ar, pm_tmr_timer, &s->io);
acpi_pm1_cnt_init(&s->ar, &s->io, s->disable_s3, s->disable_s4, s->s4_val);
acpi_gpe_init(&s->ar, GPE_LEN);
s->powerdown_notifier.notify = piix4_pm_powerdown_req;
qemu_register_powerdown_notifier(&s->powerdown_notifier);
report serial devices created with -device in the PIIX4 config space Serial and parallel devices created with -device are not reported in the PIIX4 configuration space, and are hence not picked up by the DSDT. This upsets Windows, which hides them altogether from the guest. To avoid this, check at the end of machine initialization whether the corresponding I/O ports have been registered. The new function in ioport.c does this; this also requires a tweak to isa_unassign_ioport. I left the comment in piix4_pm_initfn since the registers I moved do seem to match the 82371AB datasheet. There are some quirks though. We are setting this bit: "Device 8 EIO Enable (EIO_EN_DEV8)—R/W. 1=Enable PCI access to the device 8 enabled I/O ranges to be claimed by PIIX4 and forwarded to the ISA/EIO bus. 0=Disable. The LPT_MON_EN must be set to enable the decode." but not LPT_MON_EN (bit 18 at 50h): LPT Port Enable (LPT_MON_EN)—R/W. 1=Enable accesses to parallel port address range (LPT_DEC_SEL) to generate a device 8 (parallel port) decode event. 0=Disable. We're also setting the LPT_DEC_SEL field (that's the 0x60 written to 63h) to 11, which means reserved, rather than to 01 (378h-37Fh). Likewise we're not setting SA_MON_EN, SB_MON_EN (respectively bit 14 and bit 16 at address 50h) for the serial ports. However, we're setting COMA_DEC_SEL and COMB_DEC_SEL correctly, unlike the corresponding register for the parallel port. All these fields are left as they are, since they are probably only meant to be used in the DSDT. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2011-07-15 17:10:15 +02:00
s->machine_ready.notify = piix4_pm_machine_ready;
qemu_add_machine_init_done_notifier(&s->machine_ready);
piix4_acpi_system_hot_add_init(pci_address_space_io(dev),
pci_get_bus(dev), s);
qbus_set_hotplug_handler(BUS(pci_get_bus(dev)), OBJECT(s), &error_abort);
piix4_pm_add_propeties(s);
}
I2CBus *piix4_pm_init(PCIBus *bus, int devfn, uint32_t smb_io_base,
qemu_irq sci_irq, qemu_irq smi_irq,
int smm_enabled, DeviceState **piix4_pm)
{
DeviceState *dev;
PIIX4PMState *s;
dev = DEVICE(pci_create(bus, devfn, TYPE_PIIX4_PM));
qdev_prop_set_uint32(dev, "smb_io_base", smb_io_base);
if (piix4_pm) {
*piix4_pm = dev;
}
s = PIIX4_PM(dev);
s->irq = sci_irq;
s->smi_irq = smi_irq;
s->smm_enabled = smm_enabled;
if (xen_enabled()) {
s->use_acpi_pci_hotplug = false;
}
qdev_init_nofail(dev);
return s->smb.smbus;
}
static uint64_t gpe_readb(void *opaque, hwaddr addr, unsigned width)
{
PIIX4PMState *s = opaque;
uint32_t val = acpi_gpe_ioport_readb(&s->ar, addr);
trace_piix4_gpe_readb(addr, width, val);
return val;
}
static void gpe_writeb(void *opaque, hwaddr addr, uint64_t val,
unsigned width)
{
PIIX4PMState *s = opaque;
trace_piix4_gpe_writeb(addr, width, val);
acpi_gpe_ioport_writeb(&s->ar, addr, val);
acpi_update_sci(&s->ar, s->irq);
}
static const MemoryRegionOps piix4_gpe_ops = {
.read = gpe_readb,
.write = gpe_writeb,
.valid.min_access_size = 1,
.valid.max_access_size = 4,
.impl.min_access_size = 1,
.impl.max_access_size = 1,
.endianness = DEVICE_LITTLE_ENDIAN,
};
static bool piix4_get_cpu_hotplug_legacy(Object *obj, Error **errp)
{
PIIX4PMState *s = PIIX4_PM(obj);
return s->cpu_hotplug_legacy;
}
static void piix4_set_cpu_hotplug_legacy(Object *obj, bool value, Error **errp)
{
PIIX4PMState *s = PIIX4_PM(obj);
assert(!value);
if (s->cpu_hotplug_legacy && value == false) {
acpi_switch_to_modern_cphp(&s->gpe_cpu, &s->cpuhp_state,
PIIX4_CPU_HOTPLUG_IO_BASE);
}
s->cpu_hotplug_legacy = value;
}
static void piix4_acpi_system_hot_add_init(MemoryRegion *parent,
PCIBus *bus, PIIX4PMState *s)
{
memory_region_init_io(&s->io_gpe, OBJECT(s), &piix4_gpe_ops, s,
"acpi-gpe0", GPE_LEN);
memory_region_add_subregion(parent, GPE_BASE, &s->io_gpe);
acpi_pcihp_init(OBJECT(s), &s->acpi_pci_hotplug, bus, parent,
s->use_acpi_pci_hotplug);
s->cpu_hotplug_legacy = true;
object_property_add_bool(OBJECT(s), "cpu-hotplug-legacy",
piix4_get_cpu_hotplug_legacy,
piix4_set_cpu_hotplug_legacy,
NULL);
legacy_acpi_cpu_hotplug_init(parent, OBJECT(s), &s->gpe_cpu,
PIIX4_CPU_HOTPLUG_IO_BASE);
if (s->acpi_memory_hotplug.is_enabled) {
acpi_memory_hotplug_init(parent, OBJECT(s), &s->acpi_memory_hotplug,
ACPI_MEMORY_HOTPLUG_BASE);
}
}
static void piix4_ospm_status(AcpiDeviceIf *adev, ACPIOSTInfoList ***list)
{
PIIX4PMState *s = PIIX4_PM(adev);
acpi_memory_ospm_status(&s->acpi_memory_hotplug, list);
if (!s->cpu_hotplug_legacy) {
acpi_cpu_ospm_status(&s->cpuhp_state, list);
}
}
static void piix4_send_gpe(AcpiDeviceIf *adev, AcpiEventStatusBits ev)
{
PIIX4PMState *s = PIIX4_PM(adev);
acpi_send_gpe_event(&s->ar, s->irq, ev);
}
static Property piix4_pm_properties[] = {
DEFINE_PROP_UINT32("smb_io_base", PIIX4PMState, smb_io_base, 0),
DEFINE_PROP_UINT8(ACPI_PM_PROP_S3_DISABLED, PIIX4PMState, disable_s3, 0),
DEFINE_PROP_UINT8(ACPI_PM_PROP_S4_DISABLED, PIIX4PMState, disable_s4, 0),
DEFINE_PROP_UINT8(ACPI_PM_PROP_S4_VAL, PIIX4PMState, s4_val, 2),
DEFINE_PROP_BOOL("acpi-pci-hotplug-with-bridge-support", PIIX4PMState,
use_acpi_pci_hotplug, true),
DEFINE_PROP_BOOL("memory-hotplug-support", PIIX4PMState,
acpi_memory_hotplug.is_enabled, true),
DEFINE_PROP_END_OF_LIST(),
};
static void piix4_pm_class_init(ObjectClass *klass, void *data)
{
DeviceClass *dc = DEVICE_CLASS(klass);
PCIDeviceClass *k = PCI_DEVICE_CLASS(klass);
HotplugHandlerClass *hc = HOTPLUG_HANDLER_CLASS(klass);
AcpiDeviceIfClass *adevc = ACPI_DEVICE_IF_CLASS(klass);
k->realize = piix4_pm_realize;
k->config_write = pm_write_config;
k->vendor_id = PCI_VENDOR_ID_INTEL;
k->device_id = PCI_DEVICE_ID_INTEL_82371AB_3;
k->revision = 0x03;
k->class_id = PCI_CLASS_BRIDGE_OTHER;
dc->reset = piix4_pm_reset;
dc->desc = "PM";
dc->vmsd = &vmstate_acpi;
dc->props = piix4_pm_properties;
/*
* Reason: part of PIIX4 southbridge, needs to be wired up,
* e.g. by mips_malta_init()
*/
qdev: Replace cannot_instantiate_with_device_add_yet with !user_creatable cannot_instantiate_with_device_add_yet was introduced by commit efec3dd631d94160288392721a5f9c39e50fb2bc to replace no_user. It was supposed to be a temporary measure. When it was introduced, we had 54 cannot_instantiate_with_device_add_yet=true lines in the code. Today (3 years later) this number has not shrunk: we now have 57 cannot_instantiate_with_device_add_yet=true lines. I think it is safe to say it is not a temporary measure, and we won't see the flag go away soon. Instead of a long field name that misleads people to believe it is temporary, replace it a shorter and less misleading field: user_creatable. Except for code comments, changes were generated using the following Coccinelle patch: @@ expression DC; @@ ( -DC->cannot_instantiate_with_device_add_yet = false; +DC->user_creatable = true; | -DC->cannot_instantiate_with_device_add_yet = true; +DC->user_creatable = false; ) @@ typedef ObjectClass; expression dc; identifier class, data; @@ static void device_class_init(ObjectClass *class, void *data) { ... dc->hotpluggable = true; +dc->user_creatable = true; ... } @@ @@ struct DeviceClass { ... -bool cannot_instantiate_with_device_add_yet; +bool user_creatable; ... } @@ expression DC; @@ ( -!DC->cannot_instantiate_with_device_add_yet +DC->user_creatable | -DC->cannot_instantiate_with_device_add_yet +!DC->user_creatable ) Cc: Alistair Francis <alistair.francis@xilinx.com> Cc: Laszlo Ersek <lersek@redhat.com> Cc: Marcel Apfelbaum <marcel@redhat.com> Cc: Markus Armbruster <armbru@redhat.com> Cc: Peter Maydell <peter.maydell@linaro.org> Cc: Thomas Huth <thuth@redhat.com> Acked-by: Alistair Francis <alistair.francis@xilinx.com> Reviewed-by: Thomas Huth <thuth@redhat.com> Reviewed-by: Marcel Apfelbaum <marcel@redhat.com> Acked-by: Marcel Apfelbaum <marcel@redhat.com> Signed-off-by: Eduardo Habkost <ehabkost@redhat.com> Message-Id: <20170503203604.31462-2-ehabkost@redhat.com> [ehabkost: kept "TODO remove once we're there" comment] Reviewed-by: Markus Armbruster <armbru@redhat.com> Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
2017-05-03 22:35:44 +02:00
dc->user_creatable = false;
dc->hotpluggable = false;
hc->pre_plug = piix4_device_pre_plug_cb;
hc->plug = piix4_device_plug_cb;
hc->unplug_request = piix4_device_unplug_request_cb;
hc->unplug = piix4_device_unplug_cb;
adevc->ospm_status = piix4_ospm_status;
adevc->send_event = piix4_send_gpe;
adevc->madt_cpu = pc_madt_cpu_entry;
}
static const TypeInfo piix4_pm_info = {
.name = TYPE_PIIX4_PM,
.parent = TYPE_PCI_DEVICE,
.instance_size = sizeof(PIIX4PMState),
.class_init = piix4_pm_class_init,
.interfaces = (InterfaceInfo[]) {
{ TYPE_HOTPLUG_HANDLER },
{ TYPE_ACPI_DEVICE_IF },
pci: Add INTERFACE_CONVENTIONAL_PCI_DEVICE to Conventional PCI devices Add INTERFACE_CONVENTIONAL_PCI_DEVICE to all direct subtypes of TYPE_PCI_DEVICE, except: 1) The ones that already have INTERFACE_PCIE_DEVICE set: * base-xhci * e1000e * nvme * pvscsi * vfio-pci * virtio-pci * vmxnet3 2) base-pci-bridge Not all PCI bridges are Conventional PCI devices, so INTERFACE_CONVENTIONAL_PCI_DEVICE is added only to the subtypes that are actually Conventional PCI: * dec-21154-p2p-bridge * i82801b11-bridge * pbm-bridge * pci-bridge The direct subtypes of base-pci-bridge not touched by this patch are: * xilinx-pcie-root: Already marked as PCIe-only. * pcie-pci-bridge: Already marked as PCIe-only. * pcie-port: all non-abstract subtypes of pcie-port are already marked as PCIe-only devices. 3) megasas-base Not all megasas devices are Conventional PCI devices, so the interface names are added to the subclasses registered by megasas_register_types(), according to information in the megasas_devices[] array. "megasas-gen2" already implements INTERFACE_PCIE_DEVICE, so add INTERFACE_CONVENTIONAL_PCI_DEVICE only to "megasas". Acked-by: Alberto Garcia <berto@igalia.com> Acked-by: John Snow <jsnow@redhat.com> Acked-by: Anthony PERARD <anthony.perard@citrix.com> Signed-off-by: Eduardo Habkost <ehabkost@redhat.com> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Acked-by: David Gibson <david@gibson.dropbear.id.au> Reviewed-by: Marcel Apfelbaum <marcel@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2017-09-27 21:56:34 +02:00
{ INTERFACE_CONVENTIONAL_PCI_DEVICE },
{ }
}
};
static void piix4_pm_register_types(void)
{
type_register_static(&piix4_pm_info);
}
type_init(piix4_pm_register_types)