Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-Id: <20231221031652.119827-32-richard.henderson@linaro.org>
To support Xen guests using the Q35 chipset, the unplug protocol needs
to also remove AHCI disks.
Make pci_xen_ide_unplug() more generic, iterating over the children
of the PCI device and destroying the "ide-hd" devices. That works the
same for both AHCI and IDE, as does the detection of the primary disk
as unit 0 on the bus named "ide.0".
Then pci_xen_ide_unplug() can be used for both AHCI and IDE devices.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
When the Xen guest asks to unplug *emulated* NICs, it's kind of unhelpful
also to unplug the peer of the *Xen* PV NIC.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
The IDE unplug function needs to reset the entire PCI device, to make
sure all state is initialized to defaults. This is done by calling
pci_device_reset, which resets not only the chip specific registers, but
also all PCI state. This fixes "unplug" in a Xen HVM domU with the
modular legacy xenlinux PV drivers.
Commit ee358e919e ("hw/ide/piix: Convert reset handler to
DeviceReset") changed the way how the the disks are unplugged. Prior
this commit the PCI device remained unchanged. After this change,
piix_ide_reset is exercised after the "unplug" command, which was not
the case prior that commit. This function resets the command register.
As a result the ata_piix driver inside the domU will see a disabled PCI
device. The generic PCI code will reenable the PCI device. On the qemu
side, this runs pci_default_write_config/pci_update_mappings. Here a
changed address is returned by pci_bar_address, this is the address
which was truncated in piix_ide_reset. In case of a Xen HVM domU, the
address changes from 0xc120 to 0xc100. This truncation was a bug in
piix_ide_reset, which was fixed in commit 230dfd9257 ("hw/ide/piix:
properly initialize the BMIBA register"). If pci_xen_ide_unplug had used
pci_device_reset, the PCI registers would have been properly reset, and
commit ee358e919e would have not introduced a regression for this
specific domU environment.
While the unplug is supposed to hide the IDE disks, the changed BMIBA
address broke the UHCI device. In case the domU has an USB tablet
configured, to recive absolute pointer coordinates for the GUI, it will
cause a hang during device discovery of the partly discovered USB hid
device. Reading the USBSTS word size register will fail. The access ends
up in the QEMU piix-bmdma device, instead of the expected uhci device.
Here a byte size request is expected, and a value of ~0 is returned. As
a result the UCHI driver sees an error state in the register, and turns
off the UHCI controller.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20230720072950.20198-1-olaf@aepfle.de>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This header is now only for native Xen code, not PV backends that may be
used in Xen emulation. Since the toolstack libraries may depend on the
specific version of Xen headers that they pull in (and will set the
__XEN_TOOLS__ macro to enable internal definitions that they depend on),
the rule is that xen_native.h (and thus the toolstack library headers)
must be included *before* any of the headers in include/hw/xen/interface.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
The only thing we need to fix to make this build is the PIO hack which
sets the BIOS memory areas to R/W v.s. R/O. Theoretically we could hook
that up to the PAM registers on the emulated PIIX, but in practice
nobody cares, so just leave it doing nothing.
Now it builds without actual Xen, move it to CONFIG_XEN_BUS to include it
in the KVM-only builds.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Such that PCI passthrough devices work for Xen emulated guests.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
The 'hwaddr' type is defined in "exec/hwaddr.h" as:
hwaddr is the type of a physical address
(its size can be different from 'target_ulong').
All definitions use the 'HWADDR_' prefix, except TARGET_FMT_plx:
$ fgrep define include/exec/hwaddr.h
#define HWADDR_H
#define HWADDR_BITS 64
#define HWADDR_MAX UINT64_MAX
#define TARGET_FMT_plx "%016" PRIx64
^^^^^^
#define HWADDR_PRId PRId64
#define HWADDR_PRIi PRIi64
#define HWADDR_PRIo PRIo64
#define HWADDR_PRIu PRIu64
#define HWADDR_PRIx PRIx64
#define HWADDR_PRIX PRIX64
Since hwaddr's size can be *different* from target_ulong, it is
very confusing to read one of its format using the 'TARGET_FMT_'
prefix, normally used for the target_long / target_ulong types:
$ fgrep TARGET_FMT_ include/exec/cpu-defs.h
#define TARGET_FMT_lx "%08x"
#define TARGET_FMT_ld "%d"
#define TARGET_FMT_lu "%u"
#define TARGET_FMT_lx "%016" PRIx64
#define TARGET_FMT_ld "%" PRId64
#define TARGET_FMT_lu "%" PRIu64
Apparently this format was missed during commit a8170e5e97
("Rename target_phys_addr_t to hwaddr"), so complete it by
doing a bulk-rename with:
$ sed -i -e s/TARGET_FMT_plx/HWADDR_FMT_plx/g $(git grep -l TARGET_FMT_plx)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230110212947.34557-1-philmd@linaro.org>
[thuth: Fix some warnings from checkpatch.pl along the way]
Signed-off-by: Thomas Huth <thuth@redhat.com>
The legacy function qdev_reset_all() performs a recursive reset,
starting from a qdev. However, it does not permit any of the devices
in the tree to use three-phase reset, because device reset goes
through the device_legacy_reset() function that only calls the single
DeviceClass::reset method.
Switch to using the device_cold_reset() function instead. This also
performs a recursive reset, where first the children are reset and
then finally the parent, but it uses the new (...in 2020...)
Resettable mechanism, which supports both the old style single-reset
method and also the new 3-phase reset handling.
This commit changes the five remaining uses of this function.
Commit created with:
sed -i -e 's/qdev_reset_all/device_cold_reset/g' hw/i386/xen/xen_platform.c hw/input/adb.c hw/remote/vfio-user-obj.c hw/s390x/s390-virtio-ccw.c hw/usb/dev-uas.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This function was declared in a generic and public header, implemented
in a device-specific source file but only used in xen_platform. Given its
'aux' parameter, this function is more xen-specific than piix-specific.
Also, the hardcoded magic constants seem to be generic and related to
PCIIDEState and IDEBus rather than piix.
Therefore, move this function to xen_platform, unexport it, and drop the
"piix3" in the function name as well.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220513180957.90514-4-shentey@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Stop including exec/address-spaces.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-5-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include hw/irq.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210327050236.2232347-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
'drivers_blacklisted' is never accessed, remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20210202155644.998812-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
There's no references in only file which includes xenguest.h
to any xen definitions. And there's no references to -lxenguest
in qemu, either. Drop it.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20200727140048.19779-1-mjt@msgid.tls.msk.ru>
[perard: rebased]
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This code is not related to hardware emulation.
Move it under accel/ with the other hypervisors.
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200508100222.7112-1-philmd@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
...and xen_backend.h to xen-legacy-backend.h
Rather than attempting to convert the existing backend infrastructure to
be QOM compliant (which would be hard to do in an incremental fashion),
subsequent patches will introduce a completely new framework for Xen PV
backends. Hence it is necessary to re-name parts of existing code to avoid
name clashes. The re-named 'legacy' infrastructure will be removed once all
backends have been ported to the new framework.
This patch is purely cosmetic. No functional change.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The bus pointer in PCIDevice is basically redundant with QOM information.
It's always initialized to the qdev_get_parent_bus(), the only difference
is the type.
Therefore this patch eliminates the field, instead creating a pci_get_bus()
helper to do the type mangling to derive it conveniently from the QOM
Device object underneath.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Add INTERFACE_CONVENTIONAL_PCI_DEVICE to all direct subtypes of
TYPE_PCI_DEVICE, except:
1) The ones that already have INTERFACE_PCIE_DEVICE set:
* base-xhci
* e1000e
* nvme
* pvscsi
* vfio-pci
* virtio-pci
* vmxnet3
2) base-pci-bridge
Not all PCI bridges are Conventional PCI devices, so
INTERFACE_CONVENTIONAL_PCI_DEVICE is added only to the subtypes
that are actually Conventional PCI:
* dec-21154-p2p-bridge
* i82801b11-bridge
* pbm-bridge
* pci-bridge
The direct subtypes of base-pci-bridge not touched by this patch
are:
* xilinx-pcie-root: Already marked as PCIe-only.
* pcie-pci-bridge: Already marked as PCIe-only.
* pcie-port: all non-abstract subtypes of pcie-port are already
marked as PCIe-only devices.
3) megasas-base
Not all megasas devices are Conventional PCI devices, so the
interface names are added to the subclasses registered by
megasas_register_types(), according to information in the
megasas_devices[] array.
"megasas-gen2" already implements INTERFACE_PCIE_DEVICE, so add
INTERFACE_CONVENTIONAL_PCI_DEVICE only to "megasas".
Acked-by: Alberto Garcia <berto@igalia.com>
Acked-by: John Snow <jsnow@redhat.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 090fa1c8 "add support for unplugging NVMe disks..." extended the
existing disk unplug flag to cover NVMe disks as well as IDE and SCSI.
The recent thread on the xen-devel mailing list [1] has highlighted that
this is not desirable behaviour: PV frontends should be able to distinguish
NVMe disks from other types of disk and should have separate control over
whether they are unplugged.
This patch defines a new bit in the unplug mask for this purpose (see Xen
commit [2]) and also tidies up the definitions of, and improves the
comments regarding, the previously exiting bits in the protocol.
[1] https://lists.xen.org/archives/html/xen-devel/2017-03/msg02924.html
[2] http://xenbits.xen.org/gitweb/?p=xen.git;a=commit;h=1096aa02
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
When the guest unplugs the emulated NICs, cleanup the peer for each NIC
as it is not needed anymore. Most importantly, this allows the tap
interfaces which QEMU holds open to be closed and removed.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
This patch creates inline wrapper functions in xen_common.h for all open
coded calls to xc_hvm_XXX() functions outside of xen_common.h so that use
of xen_xc can be made implicit. This again is in preparation for the move
to using libxendevicemodel.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
The Xen HVM unplug protocol [1] specifies a mechanism to allow guests to
request unplug of 'aux' disks (which is stated to mean all IDE disks,
except the primary master). This patch adds support for that unplug request.
NOTE: The semantics of what happens if unplug of all disks and 'aux' disks
is simultaneously requests is not clear. The patch makes that
assumption that an 'all' request overrides an 'aux' request.
[1] http://xenbits.xen.org/gitweb/?p=xen.git;a=blob;f=docs/misc/hvm-emulated-unplug.markdown
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
----
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: John Snow <jsnow@redhat.com>
...not just IDE and SCSI.
This patch allows the Xen tool-stack to fully support of NVMe as an
emulated disk type. See [1] for the relevant tool-stack patch discussion.
[1] https://lists.xen.org/archives/html/xen-devel/2017-01/msg01225.html
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
The current code is poorly structured and potentially leads to multiple
config space reads when one is sufficient. Also the UNPLUG_ALL_IDE_DISKS
flag is mis-named since it also results in SCSI disks being unplugged.
This patch renames the flag and re-structures the code to be more
efficient, and readable.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Implement SUSE specific unplug protocol for emulated PCI devices
in PVonHVM guests. Its a simple 'outl(1, (ioaddr + 4));'.
This protocol was implemented and used since Xen 3.0.4.
It is used in all SUSE/SLES/openSUSE releases up to SLES11SP3 and
openSUSE 12.3.
In addition old (pre-2011) VMDP versions are handled as well.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Using 'vdev=sd[a-o]' will create an emulated LSI controller, which can
be used by the emulated BIOS to boot from disk. If the HVM domU has also
PV driver the disk may appear twice in the guest. To avoid this an
unplug of the emulated hardware is needed, similar to what is done for
IDE and NIC drivers already.
Since the SCSI controller provides only disks the entire controller can
be unplugged at once.
Impact of the change for classic and pvops based guest kernels:
vdev=sda:disk0
before: pvops: disk0=pv xvda + emulated sda
classic: disk0=pv sda + emulated sdq
after: pvops: disk0=pv xvda
classic: disk0=pv sda
vdev=hda:disk0, vdev=sda:disk1
before: pvops: disk0=pv xvda
disk1=emulated sda
classic: disk0=pv hda
disk1=pv sda + emulated sdq
after: pvops: disk0=pv xvda
disk1=not accessible by blkfront, index hda==index sda
classic: disk0=pv hda
disk1=pv sda
vdev=hda:disk0, vdev=sda:disk1, vdev=sdb:disk2
before: pvops: disk0=pv xvda
disk1=emulated sda
disk2=pv xvdb + emulated sdb
classic: disk0=pv hda
disk1=pv sda + emulated sdq
disk2=pv sdb + emulated sdr
after: pvops: disk0=pv xvda
disk1=not accessible by blkfront, index hda==index sda
disk2=pv xvdb
classic: disk0=pv hda
disk1=pv sda
disk2=pv sda
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
We can teach Xen to drain and flush each device as it needs to, instead
of trying to flush ALL devices. This removes the last user of
blk_flush_all.
The function is therefore removed under the premise that any new uses
of blk_flush_all would be the wrong paradigm: either flush the single
device that requires flushing, or use an appropriate flush_all mechanism
from outside of the BlkBackend layer.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-11-git-send-email-peter.maydell@linaro.org
Use realize to initialize the xen_platform device
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The xen-platform code crashes on reset if the xen backend is not
initialized, because it calls xc_hvm_set_mem_type(). Ensure xen-platform
won't be created without initializing the xen backend.
The assert can't be triggered by the user because the device is not
hotpluggable, and the only code creating it (at pc_xen_hvm_init())
already checks xen_enabled().
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
A number of files were including assert.h but not using any
of the functions it provides
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Device models should access their block backends only through the
block-backend.h API. Convert them, and drop direct includes of
inappropriate headers.
Just four uses of BlockDriverState are left:
* The Xen paravirtual block device backend (xen_disk.c) opens images
itself when set up via xenbus, bypassing blockdev.c. I figure it
should go through qmp_blockdev_add() instead.
* Device model "usb-storage" prompts for keys. No other device model
does, and this one probably shouldn't do it, either.
* ide_issue_trim_cb() uses bdrv_aio_discard() instead of
blk_aio_discard() because it fishes its backend out of a BlockAIOCB,
which has only the BlockDriverState.
* PC87312State has an unused BlockDriverState[] member.
The next two commits take care of the latter two.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
