The GITS_TYPE_PHYSICAL define is the value we set the
GITS_TYPER.Physical field to -- this is 1 to indicate that we support
physical LPIs. (Support for virtual LPIs is the GITS_TYPER.Virtual
field.) We also use this define as the *value* that we write into an
interrupt translation table entry's INTTYPE field, which should be 1
for a physical interrupt and 0 for a virtual interrupt. Finally, we
use it as a *mask* when we read the interrupt translation table entry
INTTYPE field.
Untangle this confusion: define an ITE_INTTYPE_VIRTUAL and
ITE_INTTYPE_PHYSICAL to be the valid values of the ITE INTTYPE
field, and replace the ad-hoc collection of ITE_ENTRY_* defines with
use of the FIELD() macro to define the fields of an ITE and the
FIELD_EX64() and FIELD_DP64() macros to read and write them.
We use ITE in the new setup, rather than ITE_ENTRY, because
ITE stands for "Interrupt translation entry" and so the extra
"entry" would be redundant.
We take the opportunity to correct the name of the field that holds
the GICv4 'doorbell' interrupt ID (this is always the value 1023 in a
GICv3, which is why we were calling it the 'spurious' field).
The GITS_TYPE_PHYSICAL define is then used in only one place, where
we set the initial GITS_TYPER value. Since GITS_TYPER.Physical is
essentially a boolean, hiding the '1' value behind a macro is more
confusing than helpful, so expand out the macro there and remove the
define entirely.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
We set the TableDesc entry_sz field from the appropriate
GITS_BASER.ENTRYSIZE field. That ID register field specifies the
number of bytes per table entry minus one. However when we use
td->entry_sz we assume it to be the number of bytes per table entry
(for instance we calculate the number of entries in a page by
dividing the page size by the entry size).
The effects of this bug are:
* we miscalculate the maximum number of entries in the table,
so our checks on guest index values are wrong (too lax)
* when looking up an entry in the second level of an indirect
table, we calculate an incorrect index into the L2 table.
Because we make the same incorrect calculation on both
reads and writes of the L2 table, the guest won't notice
unless it's unlucky enough to use an index value that
causes us to index off the end of the L2 table page and
cause guest memory corruption in whatever follows
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The extract_table_params() decodes the fields in the GITS_BASER<n>
registers into TableDesc structs. Since the fields are the same for
all the GITS_BASER<n> registers, there is currently a lot of code
duplication within the switch (type) statement. Refactor so that the
cases include only what is genuinely different for each type:
the calculation of the number of bits in the ID value that indexes
into the table.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
In extract_table_params() we process each GITS_BASER<n> register. If
the register's Valid bit is not set, this means there is no
in-guest-memory table and so we should not try to interpret the other
fields in the register. This was incorrectly coded as a 'return'
rather than a 'break', so instead of looping round to process the
next GITS_BASER<n> we would stop entirely, treating any later tables
as being not valid also.
This has no real guest-visible effects because (since we don't have
GITS_TYPER.HCC != 0) the guest must in any case set up all the
GITS_BASER<n> to point to valid tables, so this only happens in an
odd misbehaving-guest corner case.
Fix the check to 'break', so that we leave the case statement and
loop back around to the next GITS_BASER<n>.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The TableDesc struct defines properties of the in-guest-memory tables
which the guest tells us about by writing to the GITS_BASER<n>
registers. This struct currently has a union 'maxids', but all the
fields of the union have the same type (uint32_t) and do the same
thing (record one-greater-than the maximum ID value that can be used
as an index into the table).
We're about to add another table type (the GICv4 vPE table); rather
than adding another specifically-named union field for that table
type with the same type as the other union fields, remove the union
entirely and just have a 'uint32_t max_ids' struct field.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
We currently define a bitmask for the GITS_CTLR ENABLED bit in
two ways: as ITS_CTLR_ENABLED, and via the FIELD() macro as
R_GITS_CTLR_ENABLED_MASK. Consistently use the FIELD macro version
everywhere and remove the redundant ITS_CTLR_ENABLED define.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The checks in the ITS on the rdbase values in guest commands are
off-by-one: they permit the guest to pass us a value equal to
s->gicv3->num_cpu, but the valid values are 0...num_cpu-1. This
meant the guest could cause us to index off the end of the
s->gicv3->cpu[] array when calling gicv3_redist_process_lpi(), and we
would probably crash.
(This is not a security bug, because this code is only usable
with emulation, not with KVM.)
Cc: qemu-stable@nongnu.org
Fixes: 17fb5e36aa ("hw/intc: GICv3 redistributor ITS processing")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
While trying to debug a GIC ITS failure I saw some guest errors that
had poor formatting as well as leaving me confused as to what failed.
As most of the checks aren't possible without a valid dte split that
check apart and then check the other conditions in steps. This avoids
us relying on undefined data.
I still get a failure with the current kvm-unit-tests but at least I
know (partially) why now:
Exception return from AArch64 EL1 to AArch64 EL1 PC 0x40080588
PASS: gicv3: its-trigger: inv/invall: dev2/eventid=20 now triggers an LPI
ITS: MAPD devid=2 size = 0x8 itt=0x40430000 valid=0
INT dev_id=2 event_id=20
process_its_cmd: invalid command attributes: invalid dte: 0 for 2 (MEM_TX: 0)
PASS: gicv3: its-trigger: mapd valid=false: no LPI after device unmap
SUMMARY: 6 tests, 1 unexpected failures
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20211112170454.3158925-1-alex.bennee@linaro.org
Cc: Shashi Mallela <shashi.mallela@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When Enabled bit is cleared in GITS_CTLR,ITS feature continues
to be enabled.This patch fixes the issue.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20211124182246.67691-1-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implemented lpi processing at redistributor to get lpi config info
from lpi configuration table,determine priority,set pending state in
lpi pending table and forward the lpi to cpuif.Added logic to invoke
redistributor lpi processing with translated LPI which set/clear LPI
from ITS device as part of ITS INT,CLEAR,DISCARD command and
GITS_TRANSLATER processing.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210910143951.92242-7-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added ITS command queue handling for MAPTI,MAPI commands,handled ITS
translation which triggers an LPI via INT command as well as write
to GITS_TRANSLATER register,defined enum to differentiate between ITS
command interrupt trigger and GITS_TRANSLATER based interrupt trigger.
Each of these commands make use of other functionalities implemented to
get device table entry,collection table entry or interrupt translation
table entry required for their processing.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210910143951.92242-5-shashi.mallela@linaro.org
[PMM: use INTERRUPT for ItsCmdType enum name to avoid
conflict with INT type defined by Windows headers]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added functionality to trigger ITS command queue processing on
write to CWRITE register and process each command queue entry to
identify the command type and handle commands like MAPD,MAPC,SYNC.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Message-id: 20210910143951.92242-4-shashi.mallela@linaro.org
[PMM: fixed format string nit]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Defined descriptors for ITS device table,collection table and ITS
command queue entities.Implemented register read/write functions,
extract ITS table parameters and command queue parameters,extended
gicv3 common to capture qemu address space(which host the ITS table
platform memories required for subsequent ITS processing) and
initialize the same in ITS device.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Message-id: 20210910143951.92242-3-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added register definitions relevant to ITS,implemented overall
ITS device framework with stubs for ITS control and translater
regions read/write,extended ITS common to handle mmio init between
existing kvm device and newer qemu device.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Message-id: 20210910143951.92242-2-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>