The Tacoma BMC board is replacement board for the BMC of the OpenPOWER
Witherspoon system. It uses a AST2600 SoC instead of a AST2500 and the
I2C layout is the same as it controls the same main board. Used for HW
bringup.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-15-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
AspeedBoardConfig is a redundant way to define class attributes and it
complexifies the machine definition and initialization.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-14-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20191023130455.1347-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It prepares ground for the AST2600.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-18-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SOCs have two SD/MMC controllers. Add a device that
encapsulates both of these controllers and models the Aspeed-specific
registers and behavior.
Tested by reading from mmcblk0 in Linux:
qemu-system-arm -machine romulus-bmc -nographic \
-drive file=flash-romulus,format=raw,if=mtd \
-device sd-card,drive=sd0 -drive file=_tmp/kernel,format=raw,if=sd,id=sd0
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190925143248.10000-3-clg@kaod.org
[clg: - changed the controller MMIO window size to 0x1000
- moved the MMIO mapping of the SDHCI slots at the SoC level
- merged code to add SD drives on the SD buses at the machine level ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The FMC controller on the Aspeed SoCs support DMA to access the flash
modules. It can operate in a normal mode, to copy to or from the flash
module mapping window, or in a checksum calculation mode, to evaluate
the best clock settings for reads.
The model introduces two custom address spaces for DMAs: one for the
AHB window of the FMC flash devices and one for the DRAM. The latter
is populated using a "dram" link set from the machine with the RAM
container region.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190904070506.1052-6-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In struct arm_boot_info, kernel_filename, initrd_filename and
kernel_cmdline are copied from from MachineState. This patch add
MachineState as a parameter into arm_load_dtb() and move the copy chunk
of kernel_filename, initrd_filename and kernel_cmdline into
arm_load_kernel().
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Liu Jingqi <jingqi.liu@intel.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-2-tao3.xu@intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Cédric Le Goater <clg@kaod.org>
[ehabkost: include hw/boards.h again to fix build failures]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
The global smp variables in arm are replaced with smp machine properties.
The init_cpus() and *_create_rpu() are refactored to pass MachineState.
A local variable of the same name would be introduced in the declaration
phase if it's used widely in the context OR replace it on the spot if it's
only used once. No semantic changes.
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190518205428.90532-9-like.xu@linux.intel.com>
[ehabkost: Fix hw/arm/sbsa-ref.c and hw/arm/aspeed.c]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The Swift board is an OpenPOWER system hosting POWER processors.
Add support for their BMC including the I2C devices as found on HW.
Signed-off-by: Adriana Kobylak <anoo@us.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-20-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The RAM memory region is defined after the SoC is realized when the
SDMC controller has checked that the defined RAM size for the machine
is correct. This is problematic for controller models requiring a link
on the RAM region, for DMA support in the SMC controller for instance.
Introduce a container memory region for the RAM that we can link into
the controllers early, before the SoC is realized. It will be
populated with the RAM region after the checks have be done.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-14-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It has never been used as far as I can tell from the git history.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-13-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The current models of the Aspeed SoCs only have one CPU but future
ones will support SMP. Introduce a new num_cpus field at the SoC class
level to define the number of available CPUs per SoC and also
introduce a 'num-cpus' property to activate the CPUs configured for
the machine.
The max_cpus limit of the machine should depend on the SoC definition
but, unfortunately, these values are not available when the machine
class is initialized. This is the reason why we add a check on
num_cpus in the AspeedSoC realize handler.
SMP support will be activated when models for such SoCs are implemented.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-6-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will simplify the definition of new SoCs, like the AST2600 which
should use a slightly different address space and have a different set
of controllers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
As explained in commit aff39be0ed97:
Both functions, object_initialize() and object_property_add_child()
increase the reference counter of the new object, so one of the
references has to be dropped afterwards to get the reference
counting right. Otherwise the child object will not be properly
cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the
reference counting here right.
This patch was generated using the following Coccinelle script
(with a bit of manual fix-up for overly long lines):
@use_object_initialize_child@
expression parent_obj;
expression child_ptr;
expression child_name;
expression child_type;
expression child_size;
expression errp;
@@
(
- object_initialize(child_ptr, child_size, child_type);
+ object_initialize_child(parent_obj, child_name, child_ptr, child_size,
+ child_type, &error_abort, NULL);
... when != parent_obj
- object_property_add_child(parent_obj, child_name, OBJECT(child_ptr), NULL);
...
?- object_unref(OBJECT(child_ptr));
|
- object_initialize(child_ptr, child_size, child_type);
+ object_initialize_child(parent_obj, child_name, child_ptr, child_size,
+ child_type, errp, NULL);
... when != parent_obj
- object_property_add_child(parent_obj, child_name, OBJECT(child_ptr), errp);
...
?- object_unref(OBJECT(child_ptr));
)
@use_sysbus_init_child_obj@
expression parent_obj;
expression dev;
expression child_ptr;
expression child_name;
expression child_type;
expression child_size;
expression errp;
@@
(
- object_initialize_child(parent_obj, child_name, child_ptr, child_size,
- child_type, errp, NULL);
+ sysbus_init_child_obj(parent_obj, child_name, child_ptr, child_size,
+ child_type);
...
- qdev_set_parent_bus(DEVICE(child_ptr), sysbus_get_default());
|
- object_initialize_child(parent_obj, child_name, child_ptr, child_size,
- child_type, errp, NULL);
+ sysbus_init_child_obj(parent_obj, child_name, child_ptr, child_size,
+ child_type);
- dev = DEVICE(child_ptr);
- qdev_set_parent_bus(dev, sysbus_get_default());
)
While the object_initialize() function doesn't take an
'Error *errp' argument, the object_initialize_child() does.
Since this code is used when a machine is created (and is not
yet running), we deliberately choose to use the &error_abort
argument instead of ignoring errors if an object creation failed.
This choice also matches when using sysbus_init_child_obj(),
since its code is:
void sysbus_init_child_obj(Object *parent,
const char *childname, void *child,
size_t childsize, const char *childtype)
{
object_initialize_child(parent, childname, child, childsize,
childtype, &error_abort, NULL);
qdev_set_parent_bus(DEVICE(child), sysbus_get_default());
}
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Inspired-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20190507163416.24647-8-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The header file hw/arm/arm.h now includes only declarations
relating to hw/arm/boot.c functionality. Rename it accordingly,
and adjust its header comment.
The bulk of this commit was created via
perl -pi -e 's|hw/arm/arm.h|hw/arm/boot.h|' hw/arm/*.c include/hw/arm/*.h
In a few cases we can just delete the #include:
hw/arm/msf2-soc.c, include/hw/arm/aspeed_soc.h and
include/hw/arm/bcm2836.h did not require it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190516163857.6430-4-peter.maydell@linaro.org
We currently use Qemu's default of 128MB. As we know how much ram each
machine ships with, make it easier on users by setting a default.
It can still be overridden with -m on the command line.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190503022958.1394-1-joel@jms.id.au
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-2-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
smbus.c and smbus.h had device side code, master side code, and
smbus.h has some smbus_eeprom.c definitions. Split them into
separate files.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
When using clang 3.4.2, compilation of QEMU fails like this:
CC aarch64-softmmu/hw/arm/aspeed.o
hw/arm/aspeed.c:36:3: error: redefinition of typedef 'AspeedBoardState' is a C11
feature [-Werror,-Wtypedef-redefinition]
} AspeedBoardState;
^
include/hw/arm/aspeed.h:14:33: note: previous definition is here
typedef struct AspeedBoardState AspeedBoardState;
^
1 error generated.
make[1]: *** [hw/arm/aspeed.o] Error 1
make: *** [subdir-aarch64-softmmu] Error 2
Remove the duplicated typedef to fix this issue.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1543397736-8198-1-git-send-email-thuth@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The code looks better, it removes duplicated lines and it will ease
the introduction of common properties for the Aspeed machines.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180921161939.822-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2500 evb is shipped with a W25Q256 which has a non volatile bit
to make the chip operate in 4 Byte address mode at power up. This
should be an interesting feature to model as it will exercise a bit
more the SMC controllers and MMIO execution at boot time.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180921161939.822-3-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will be used to construct a memory region beyond the RAM region
to let firmwares scan the address space with load/store to guess how
much RAM the SoC has.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180807075757.7242-7-joel@jms.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The pca9552 LED blinkers on the Witherspoon machine are used for leds
but also as GPIOs to control fans and GPUs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180530064049.27976-8-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed boards have at least one EEPROM to hold the Vital Product
Data (VPD).
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180530064049.27976-6-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2500 EVB does not have an RTC but we can pretend that one is
plugged on the I2C bus header.
The romulus and witherspoon boards expects an Epson RX8900 I2C RTC but
a ds1338 is good enough for the basic features we need.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180530064049.27976-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Witherspoon boards are OpenPOWER system hosting POWER9 Processors.
Add support for their BMC including a couple of I2C devices as found
on real HW.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180530064049.27976-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180530064049.27976-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently we use memory_region_init_ram_nomigrate() to create
the "aspeed.boot_rom" memory region, and we don't manually
register it with vmstate_register_ram(). This currently
means that its contents are migrated but as a ram block
whose name is the empty string; in future it may mean they
are not migrated at all. Use memory_region_init_ram() instead.
Note that would be a cross-version migration compatibility break
for the "palmetto-bmc", "ast2500-evb" and "romulus-bmc" machines,
but migration is currently broken for them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180420124835.7268-3-peter.maydell@linaro.org
The ASPEED hardware contains a lock register for the SCU that disables
any writes to the SCU when it is locked. The machine comes up with the
lock enabled, but on all known hardware u-boot will unlock it and leave
it unlocked when loading the kernel.
This means the kernel expects the SCU to be unlocked. When booting from
an emulated ROM the normal u-boot unlock path is executed. Things don't
go well when booting using the -kernel command line, as u-boot does not
run first.
Change behaviour so that when a kernel is passed to the machine, set the
reset value of the SCU to be unlocked.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20171114122018.12204-1-joel@jms.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Set the MachineClass flag ignore_memory_transaction_failures
for almost all ARM boards. This means they retain the legacy
behaviour that accesses to unimplemented addresses will RAZ/WI
rather than aborting, when a subsequent commit adds support
for external aborts.
The exceptions are:
* virt -- we know that guests won't try to prod devices
that we don't describe in the device tree or ACPI tables
* mps2 -- this board was written to use unimplemented-device
for all the ranges with devices we don't yet handle
New boards should not set the flag, but instead be written
like the mps2.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1504626814-23124-3-git-send-email-peter.maydell@linaro.org
For the Xilinx boards:
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Rename memory_region_init_rom() to memory_region_init_rom_nomigrate()
and memory_region_init_rom_device() to
memory_region_init_rom_device_nomigrate().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1499438577-7674-5-git-send-email-peter.maydell@linaro.org
This property is an alias for device TYPE_ASPEED_SDMC's property
"ram-size", which is defined with DEFINE_PROP_UINT64().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20170607163635.17635-25-marcandre.lureau@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Temperatures can be changed from the monitor with :
(qemu) qom-set /machine/unattached/device[2] temperature0 12000
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1496739230-32109-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Let's add an RTC to the palmetto BMC and a LM75 temperature sensor to
the AST2500 EVB to start with.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1494827476-1487-5-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
The flash devices used for the FMC controller (BMC firmware) are well
defined for each Aspeed machine and are all smaller than the default
mapping window size, at least for CE0 which is the chip the SoC boots
from.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1486648058-520-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
write_boot_rom() does not check for negative values. This is more a
problem for coverity than the actual code as the size of the flash
device is checked when the m25p80 object is created. If there is
anything wrong with the backing file, we should not even reach that
path.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1486648058-520-2-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a ROM region, using the default size of the mapping window for
the CE0 FMC flash module, and fill it with the flash content.
This is a little hacky but until we can boot from a MMIO region, it
seems difficult to do anything else.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-11-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a new configuration field at the board level and propagate the
value using the "num-cs" property of the FMC controller model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1480434248-27138-14-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The palmetto BMC machine uses a AST2400 revision A1 SoC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1480434248-27138-11-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Romulus machine is an OpenPOWER system with an AST2500 SoC for
the BMC and a POWER9 chip for the host. It does not make much
difference for qemu a part from the fact that the FMC controller has
two SPI flash module.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 1480434248-27138-8-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Future machine will use different flash models for the FMC and the SPI
controllers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1480434248-27138-7-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2500 SoC has two. Let's prepare ground for the next changes
which will add the required definitions for the second host SPI
controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-4-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SoC has three different types of SMC (Static Memory
Controller) controllers: the SMC (legacy), the FMC (the new one) and
the SPI for the host PNOR. The FMC and the SPI models are now
converging on the AST2500 SoC and the SMC, which was still available
on the AST2400 SoC, was removed.
The Aspeed SoC does not provide support for the legacy SMC
controller. So, let's rename the 'smc' object to 'fmc' to clarify its
nature.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-2-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the RAM size is invalid, the memory controller will use a default
value.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1473438177-26079-15-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Configure the size of the RAM of the SOC using a property to propagate
the value down to the memory controller from the board level.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1473438177-26079-14-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1473438177-26079-11-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ast2500 eval board has a hardware strapping register value of
0xF100C2E6 which we use for a definition of AST2500_EVB_HW_STRAP1
below.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1473438177-26079-10-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Cédric Le Goater
Eddie James
Tao Xu
Markus Armbruster
Like Xu
Adriana Kobylak
Philippe Mathieu-Daudé
Peter Maydell
Joel Stanley
Corey Minyard
Thomas Huth
Philippe Mathieu-Daudé
Marc-André Lureau