In a real AHCI device, several S/ATA registers are mirrored or shadowed
within the AHCI register set. These registers are not updated
synchronously for each read access, but are instead updated after a
Device-to-Host Register FIS packet is received. The D2H FIS contains
the values from these registers on the device.
In QEMU, by reaching directly into the device to grab these bits before
they are "sent," we may introduce race conditions where unexpected
values are present "before they are sent" which could cause issues for
some guests, particularly if an attempt is made to read the PxTFD
register prior to enabling the port, where incorrect values will be read.
This patch also addresses the boot-time values for the PxTFD and PxSIG
registers to bring them in line with the AHCI 1.3 specification.
Lastly, several fields (PxTFD, PxSIG and PxSACT) are read-only,
and any attempts to write to them should be ignored.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1408643079-30675-6-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In the Intel ICH9 data sheet, the MSI capability offset
in the PCI configuration space for ICH9 AHCI devices is
specified to be 0x80.
Further, the PCI capability pointer should always point
to 0x80 in ICH9 devices, despite the fact that AHCI 1.3
specifies that it should be pointing to PMCAP (Which in
this instance would be 0x70) to maintain adherence to
the Intel data sheet specifications and real observed behavior.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1408643079-30675-3-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We know that either bh is scheduled or ide_issue_trim_cb will be called
again, so we just set i, j and ret to the right values. In both cases,
ide_trim_bh_cb will be called.
Also forward the cancellation to the iocb->aiocb which we get from
bdrv_aio_discard.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Before, bdrv_aio_cancel will either complete the request (like normal)
and call CB with an actual return code, or skip calling the request (for
example when the IO req is not submitted by thread pool yet).
We will change bdrv_aio_cancel to do it differently: always call CB
before return, with either [1] a normal req completion ret code, or [2]
ret == -ECANCELED. So the callers' callback must accept both cases. The
existing logic works with case [1], but not [2].
The simplest transition of callback code is do nothing in case [2], just
as if the CB is not called by the bdrv_aio_cancel() call.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
When the command completion code in IDE and AHCI
was unified to put all command completion inside
of a callback, "cmd_done," we neglected to
ensure that all AHCI/ATAPI command paths would
eventually register as finished. for the PCI
interface to IDE this is not a problem because
cmd_done is a nop, but the AHCI implementation
needs to send a D2H_REG_FIS and interrupt back
to the guest to inform of completion.
This patch adds calls to ide_stop_transfer,
which calls ide_cmd_done, inside of
ide_atapi_cmd_ok and ide_atapi_cmd_error.
This fixes regressions observed by trying to boot QEMU
with a Fedora 20 live CD under Q35/AHCI, which uses
ATAPI command 0x00, which is a status check that may
cause a hang because we never complete, and ATAPI
command 0x56, which is unsupported by our current
implementation and results in an error that we never
report back to the guest.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
A bunch of bugfixes - some of these will make sense for 2.1.2
I put Cc: qemu-stable included where appropriate.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUGyniAAoJECgfDbjSjVRpxg0H/j4jSEWHm/4uKSly6W4MXxhN
LghE5iAaO3awU88RiRPW/m/g6sagD9RuQAHteHkvyZ6py/li0IFvLtl66OczeSgc
rnM2n9MeYfi5Q05T+ygjqYY2ynosYhrI4iPmsnKqbqLi+WWwQHFKuYKNcNmQjmJu
Sg4KDz+W4p5j/pMUZdgf4lse3PaLXoMy4IA1HC8U1WmwvyNLZrPRTXhFn1hFbxU6
Rf604wz6gkAFvwizt2SoRMOIF4w0meCKemY1wqcwOeDWqP6Bj76RnRCrVR06AgnX
ngVsrP5SrWymqwFUP9ZpeNdBOQSxXE3zT1cE6JU3/KUvTBs6Eur4Dnz7g2mPb8I=
=nHHz
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pci, pc, virtio, misc bugfixes
A bunch of bugfixes - some of these will make sense for 2.1.2
I put Cc: qemu-stable included where appropriate.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 18 Sep 2014 19:52:18 BST using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream:
pc: leave more space for BIOS allocations
virtio-pci: fix migration for pci bus master
vhost-user: fix VIRTIO_NET_F_MRG_RXBUF negotiation
virtio-pci: enable bus master for old guests
Revert "virtio: don't call device on !vm_running"
virtio-net: drop assert on vm stop
Revert "rng-egd: remove redundant free"
qdev: Move global validation to a single function
qdev: Rename qdev_prop_check_global() to qdev_prop_check_globals()
test-qdev-global-props: Test handling of hotpluggable and non-device types
test-qdev-global-props: Initialize not_used=true for all props
test-qdev-global-props: Run tests on subprocess
tests: disable global props test for old glib
test-qdev-global-props: Trivial comment fix
hw/machine: Free old values of string properties
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since QEMU 2.1, we are allocating more space for ACPI tables, so no
space is left after initrd for the BIOS to allocate memory.
Besides ACPI tables, there are a few other uses of high memory in
SeaBIOS: SMBIOS tables and USB drivers use it in particular. These uses
allocate a very small amount of memory. Malloc metadata also lives
there. So we need _some_ extra padding there to avoid initrd breakage,
but not much.
John Snow found a case where RHEL5 was broken by the recent change to
ACPI_TABLE_SIZE; in his case 4KB of extra padding are fine, but just to
be safe I am adding 32KB, which is roughly the same amount of padding
that was left by QEMU 2.0 and earlier.
Move initrd to leave some space for the BIOS.
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reported-by: John Snow <jsnow@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Current support for bus master (clearing OK bit)
together with the need to support guests which do not
enable PCI bus mastering, leads to extra state in
VIRTIO_PCI_FLAG_BUS_MASTER_BUG bit, which isn't robust
in case of cross-version migration for the case when
guests use the device before setting DRIVER_OK.
Rip out VIRTIO_PCI_FLAG_BUS_MASTER_BUG and implement a simpler
work-around: treat clearing of PCI_COMMAND as a virtio reset. Old
guests never touch this bit so they will work.
As reset clears device status, DRIVER and MASTER bits are
now in sync, so we can fix up cross-version migration simply
by synchronising them, without need to detect a buggy guest
explicitly.
Drop tracking VIRTIO_PCI_FLAG_BUS_MASTER_BUG completely.
As reset makes the device quiescent, in the future we'll be able to drop
checking OK bit in a bunch of places.
Cc: Jason Wang <jasowang@redhat.com>
Cc: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Header length check should happen only if backend is kernel. For user
backend there is no reason to reset this bit.
vhost-user code does not define .has_vnet_hdr_len so
VIRTIO_NET_F_MRG_RXBUF cannot be negotiated even if both sides
support it.
Signed-off-by: Damjan Marion <damarion@cisco.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
commit cc943c36fa
pci: Use bus master address space for delivering MSI/MSI-X messages
breaks virtio-net for rhel6.[56] x86 guests because they don't
enable bus mastering for virtio PCI devices. For the same reason,
rhel6.[56] ppc64 guests cannot boot on a virtio-blk disk anymore.
Old guests forgot to enable bus mastering, enable it automatically on
DRIVER (guests use some devices before DRIVER_OK).
Reported-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Tested-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit a1bc7b827e422e1ff065640d8ec5347c4aadfcd8.
virtio: don't call device on !vm_running
It turns out that virtio net assumes that vm_running
is updated before device status callback in many places,
so this change leads to asserts.
Previous commit fixes the root issue that motivated
a1bc7b827e422e1ff065640d8ec5347c4aadfcd8 differently,
so there's no longer a need for this change.
In the future, we might be able to drop checking vm_running
completely, and check vm state directly.
Reported-by: Dietmar Maurer <dietmar@proxmox.com>
Cc: qemu-stable@nongnu.org
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
On vm stop, vm_running state set to stopped
before device is notified, so callbacks can get envoked with
vm_running = false; and this is not an error.
Cc: qemu-stable@nongnu.org
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently GlobalProperty.not_used=false has multiple meanings:
* It may be a property for a hotpluggable device, which may or may not
have been used by a device;
* It may be a machine-type-provided property, which may or may not have
been used by a device.
* It may be a user-provided property that was actually not used by
any device.
Simplify the logic by having two separate fields: 'user_provided' and
'used'. This allows the entire global property validation logic to be
contained in a single function, and allows more specific error messages.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=3He1
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block patches
# gpg: Signature made Fri 12 Sep 2014 16:09:43 BST using RSA key ID C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
* remotes/kevin/tags/for-upstream: (22 commits)
qcow2: Add falloc and full preallocation option
raw-posix: Add falloc and full preallocation option
qapi: introduce PreallocMode and new PreallocModes full and falloc.
block: don't convert file size to sector size
block: round up file size to nearest sector
iotests: Send the correct fd in socket_scm_helper
blockdev: Refuse to drive_del something added with blockdev-add
block: extend BLOCK_IO_ERROR with reason string
dataplane: fix virtio_blk_data_plane_create() op blocker error path
qemu-iotests: Run 025 for Archipelago block driver
block/archipelago: Implement bdrv_truncate()
block: Make the block accounting functions operate on BlockAcctStats
block: rename BlockAcctType members to start with BLOCK_ instead of BDRV_
block: Extract the block accounting code
block: Extract the BlockAcctStats structure
IDE: MMIO IDE device control should be little endian
thread-pool: Drop unnecessary includes
xen: Drop redundant bdrv_close() from pci_piix3_xen_ide_unplug()
xen_disk: Plug memory leak on error path
qemu-io: Clean up openfile() after commit 2e40134
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Amos Kong <akong@redhat.com>
Cc: qemu-stable@nongnu.org
- Build: fixing block/iscsi.so and ranlib warnings on Mac OS X
- Migration fixes for x86
- The odd KVM patch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=GIKW
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
- Memory: improve error reporting and avoid crashes on hotplug
- Build: fixing block/iscsi.so and ranlib warnings on Mac OS X
- Migration fixes for x86
- The odd KVM patch.
# gpg: Signature made Thu 11 Sep 2014 11:21:10 BST using RSA key ID 9B4D86F2
# gpg: Good signature from "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: aka "Paolo Bonzini <bonzini@gnu.org>"
* remotes/bonzini/tags/for-upstream: (21 commits)
gdbstub: init mon_chr through qemu_chr_alloc
pckbd: adding new fields to vmstate
mc146818rtc: add missed field to vmstate
piix: do not set irq while loading vmstate
serial: fixing vmstate for save/restore
parallel: adding vmstate for save/restore
fdc: adding vmstate for save/restore
cpu: init vmstate for ticks and clock offset
apic_common: vapic_paddr synchronization fix
vl: use QLIST_FOREACH_SAFE to visit change state handlers
exec: add parameter errp to gethugepagesize
exec: report error when memory < hpagesize
hostmem-ram: don't exit qemu if size of memory-backend-ram is way too big
memory: add parameter errp to memory_region_init_rom_device
memory: add parameter errp to memory_region_init_ram
exec: add parameter errp to qemu_ram_alloc and qemu_ram_alloc_from_ptr
rules.mak: Fix DSO build by pulling in archive symbols
util: Don't link host-utils.o if it's empty
util: Move general qemu_getauxval to util/getauxval.c
trace: Only link generated-tracers.o with "simple" backend
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for loading DTB images when booting ELF images using
-kernel. If there are no conflicts with the placement of the ELF
segments, the DTB image is loaded at the base of RAM.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 1410453915-9344-5-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If we are running the 'virt' machine, we may have a device tree blob but no
kernel to supply it to if no -kernel option was passed. In that case, copy it
to the base of RAM where it can be picked up by a bootloader.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 1410453915-9344-4-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an address limit input parameter to load_dtb() so that we can
tell load_dtb() how much memory the dtb is allowed to consume. If
the dtb doesn't fit, return 0, otherwise return the actual size of
the loaded dtb.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 1410453915-9344-3-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In order to make the device tree blob (DTB) available in memory not only at
first boot, but also after system reset, use rom_blob_add_fixed() to install
it into memory.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 1410453915-9344-2-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The pl011 and pl031 devices both use level triggered interrupts,
but the device tree we construct was incorrectly telling the
kernel to configure the GIC to treat them as edge triggered.
This meant that output from the pl011 would hang after a while.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1410274423-9461-1-git-send-email-peter.maydell@linaro.org
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Cc: qemu-stable@nongnu.org
Add two flash devices to the virt board, so that it can be used for
running guests which want a bootrom image such as UEFI. We provide
two flash devices to make it more convenient to provide both a
read-only UEFI image and a read-write place to store guest-set
UEFI config variables. The '-bios' command line option is set up
to provide an image for the first of the two flash devices.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1409930126-28449-2-git-send-email-ard.biesheuvel@linaro.org
This patch adds the missing input interrupt logic to the pl061 GPIO device. To
keep the floating output pins to stay high, the old state variable had to be
split into two separate ones for input and output - which brings the vmstate
version to 3.
Edge level interrupts and I/O were tested under Linux 3.14. Level interrupt
handling hasn't been tested.
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Message-id: 54024FD2.9080204@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a property "linux,stdout-path" to the /chosen DT node and make
it point to the emulated UART. This allows users such as the Linux
kernel to produce console output without the need to pass console=
or earlycon=pl011,0x... command line arguments.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 1409317439-29349-1-git-send-email-ard.biesheuvel@linaro.org
Reviewed-by: Rob Herring <rob.herring@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 3718d8ab65 ("block: Replace in_use
with operation blocker") broke the error path because it consumed
local_err instead of propagating it.
The caller has no way to know that the function failed. This caused
virtio-blk to start "successfully" even though there was a fatal
dataplane error.
Steps to reproduce:
$ qemu-system-x86_64 -enable-kvm -object iothread,id=iothread0 \
-drive if=none,id=drive0,file=a.img \
(qemu) drive_mirror drive0 /tmp/foo.img
(qemu) device_add virtio-blk-pci,iothread=iothread0,drive=drive0
Expected result:
Since the mirror block job is using drive0 it is not possible to start
virtio-blk data-plane.
device_add fails and the PCI adapter is not added.
Actual result:
device_add completes and the PCI adapter is added.
Cc: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds outport to VMState to allow correct saving and restoring
the state of PC keyboard controller.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds irq_reinject_on_ack_count field to VMState to allow correct
saving/loading the state of MC146818 RTC.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Acked-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch avoids setting an irq while loading the state of the ISA bridge.
Because the i8259 has not been deserialized yet, raising an interrupt
could bring the system out-of-sync with the migration source. For example,
the migration source could have masked the interrupt in the i8259. On the
destination, the i8259 device model would not know that yet and would
trigger an interrupt in the CPU.
This patch eliminates setting the irq and just restores the calculated
state fields in post_load function. Interrupt state will be deserialized
separately through the IRR field of the i8259.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some fields were added to VMState by this patch to preserve correct
loading of the serial port controller state.
Updating FCR value while loading was also modified to disable generating
an interrupt by loadvm.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMState added by this patch preserves correct
loading of the parallel port controller state.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Acked-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMState added by this patch preserves correct
loading of the FDC device state.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Acked-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch postpones vapic_paddr initialization, which is performed
during migration. When vapic_paddr is synchronized within the migration
process, apic_common functions could operate with incorrect apic state,
if it hadn't loaded yet. This patch postpones the synchronization until
the virtual machine is started, ensuring that the whole virtual machine
state has been loaded.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Tested-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is the next step for decoupling block accounting functions from
BlockDriverState.
In a future commit the BlockAcctStats structure will be moved from
BlockDriverState to the device models structures.
Note that bdrv_get_stats was introduced so device models can retrieve the
BlockAcctStats structure of a BlockDriverState without being aware of it's
layout.
This function should go away when BlockAcctStats will be embedded in the device
models structures.
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Keith Busch <keith.busch@intel.com>
CC: Anthony Liguori <aliguori@amazon.com>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Eric Blake <eblake@redhat.com>
CC: Peter Maydell <peter.maydell@linaro.org>
CC: Michael Tokarev <mjt@tls.msk.ru>
CC: John Snow <jsnow@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Alexander Graf <agraf@suse.de>
CC: Max Reitz <mreitz@redhat.com>
Signed-off-by: Benoît Canet <benoit.canet@nodalink.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The middle term goal is to move the BlockAcctStats structure in the device models.
(Capturing I/O accounting statistics in the device models is good for billing)
This patch make a small step in this direction by removing a reference to BDRV.
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Keith Busch <keith.busch@intel.com>
CC: Anthony Liguori <aliguori@amazon.com>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: John Snow <jsnow@redhat.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Markus Armbruster <armbru@redhat.com>
CC: Alexander Graf <agraf@suse.de>i
Signed-off-by: Benoît Canet <benoit.canet@nodalink.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Set the IDE MMIO memory type to little endian. The ATA specs identify
words part of the control commands encoded as little endian.
While this has no impact on little endian systems, it's required for big
endian systems(eg OpenRisc).
Signed-off-by: Valentin Manea <valentin.manea@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The Error object was leaked after failed bdrv_new(). While there,
streamline control flow a bit.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add back the PCIe config capabilities on XHCI cards in non-PCIe slots,
but only for machine types before 2.1.
This fixes a migration incompatibility in the XHCI PCI devices
caused by:
058fdcf52c - xhci: add endpoint cap on express bus only
Note that in fixing it for compatibility with older QEMUs, it breaks
compatibility with existing QEMU 2.1's on older machine types.
The status before this patch was (if it used an XHCI adapter):
machine type | source qemu
any pre-2.1 - FAIL
any 2.1... - PASS
With this patch:
machine type | source qemu
any pre-2.1 - PASS
pre-2.1 2.1... - FAIL
2.1 2.1... - PASS
A test to trigger it is to add '-device nec-usb-xhci,id=xhci,addr=0x12'
to the command line.
Cc: qemu-stable@nongnu.org
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add parameter errp to memory_region_init_rom_device and update all call
sites to propagate the error.
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
[Propagate the error out of realize. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add parameter errp to memory_region_init_ram and update all call sites
to pass in &error_abort.
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both OpenBSD and FreeBSD SPARC64 attempt to read the interrupt map from the
hardware and will fail if the correct ino isn't present.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Alexander Graf (11):
PPC: KVM: Fix g3beige and mac99 when HV is loaded
PPC: mac99: Move NVRAM to page boundary when necessary
KVM: Add helper to run KVM_CHECK_EXTENSION on vm fd
PPC: KVM: Use vm check_extension for pv hcall
PPC: mac99: Fix core99 timer frequency
PPC: mac_nvram: Remove unused functions
PPC: mac_nvram: Allow 2 and 4 byte accesses
PPC: mac_nvram: Split NVRAM into OF and OSX parts
PPC: Mac: Move tbfreq into local variable
PPC: Cuda: Use cuda timer to expose tbfreq to guest
PPC: Fix default config ordering and add eTSEC for ppc64
Alexey Kardashevskiy (7):
spapr: Move DT memory node rendering to a helper
spapr: Use DT memory node rendering helper for other nodes
spapr: Refactor spapr_populate_memory() to allow memoryless nodes
spapr: Split memory nodes to power-of-two blocks
spapr: Add a helper for node0_size calculation
spapr: Fix ibm, associativity for memory nodes
spapr_pci: Fix config space corruption
Anton Blanchard (2):
spapr-vlan: Don't touch last entry in buffer list
hypervisor property clashes with hypervisor node
Benjamin Herrenschmidt (2):
loader: Add load_image_size() to replace load_image()
spapr: Locate RTAS and device-tree based on real RMA
Bharat Bhushan (4):
ppc: debug stub: Get trap instruction opcode from KVM
ppc: synchronize excp_vectors for injecting exception
ppc: Add software breakpoint support
ppc: Add hw breakpoint watchpoint support
Gonglei (1):
spapr: fix possible memory leak
Greg Kurz (1):
spapr_pci: map the MSI window in each PHB
Nikunj A Dadhania (3):
ppc: spapr-rtas - implement os-term rtas call
spapr: add uuid/host details to device tree
ppc/spapr: Fix MAX_CPUS to 255
Peter Maydell (1):
hw/ppc/spapr_hcall.c: Fix typo in function names
Tom Musta (20):
linux-user: Fix Stack Pointer Bug in PPC setup_rt_frame
linux-user: Split PPC Trampoline Encoding from Register Save
linux-user: Enable Signal Handlers on PPC64
linux-user: Properly Dereference PPC64 ELFv1 Signal Handler Pointer
linux-user: Implement do_setcontext for PPC64
linux-user: Handle PPC64 ELFv2 Function Pointers
target-ppc: Bug Fix: rlwinm
target-ppc: Bug Fix: rlwnm
target-ppc: Bug Fix: rlwimi
target-ppc: Bug Fix: mullwo
target-ppc: Bug Fix: mullw
target-ppc: Bug Fix: mulldo OV Detection
target-ppc: Bug Fix: srawi
target-ppc: Bug Fix: srad
target-ppc: Special Case of rlwimi Should Use Deposit
target-ppc: Optimize rlwinm MB=0 ME=31
target-ppc: Optimize rlwnm MB=0 ME=31
target-ppc: Clean Up mullw
target-ppc: Clean up mullwo
target-ppc: Implement mulldo with TCG
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJUDYojAAoJECszeR4D/txgyXoQAJ3ZZhOwfQEXl7GgUCmUqLfO
4a33CgaSq85buQfWiuMLk709iCLgjIoTY1xpHCGuyPHEXdlmJnfNlBXrwYhhU9Wx
F7VCDSB6k+itVKJymaD8JSOU+GrSmiTE/OqTb89W8LWXGJgYJFmHpwmmMNia+dc9
AAH47MZuJzCRuc9sgk7a1bRjk8NwV8BZksoZspP8THqmOZAXBiMxfO/lf2NL3kJW
9JHiedM+AJxtOg5GFpf91LKF0ozXvE9UghWiLrq7Y5KOzHqcxlTyD59JK7dllNtP
UHWJfiL3r2yD2TpMlNcQbBgomFpEGViHQU44ClXtwSINpc6y8Uq9YsJKVCB4mbSZ
Y+hzAWEGFcXBLcSY5uaG4FEcOVDOwCPe+dWzR1GIGDUW3SQKEiK11P3dX+OuRFN+
B6qnaJU1NST3CwMtqq7+anfbJx6AqPkYLWKMDXy308AJllUXi6QFFwJqjNB+Te6U
yRbfOkv6XOhEpp1kRXdar+8AZO7xCerRdnmO4H5vx0QwnkVZtADG7pVWHMx2onhB
1485XZ+d9y2uTm5z7Pd/RjUls9AegWk73pqWceh+IlyTNTZHicH5te1ZjCx0me/d
XkZgaXhO4tPLMahzdrCoSPrfleduB4Y8cPficv7eQK/JFNMQVCuybBq5td2hrSce
p6y0rEHZtBo+8zml/RdZ
=lpcC
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/agraf/tags/signed-ppc-for-upstream' into staging
Patch queue for ppc - 2014-09-08
Alexander Graf (11):
PPC: KVM: Fix g3beige and mac99 when HV is loaded
PPC: mac99: Move NVRAM to page boundary when necessary
KVM: Add helper to run KVM_CHECK_EXTENSION on vm fd
PPC: KVM: Use vm check_extension for pv hcall
PPC: mac99: Fix core99 timer frequency
PPC: mac_nvram: Remove unused functions
PPC: mac_nvram: Allow 2 and 4 byte accesses
PPC: mac_nvram: Split NVRAM into OF and OSX parts
PPC: Mac: Move tbfreq into local variable
PPC: Cuda: Use cuda timer to expose tbfreq to guest
PPC: Fix default config ordering and add eTSEC for ppc64
Alexey Kardashevskiy (7):
spapr: Move DT memory node rendering to a helper
spapr: Use DT memory node rendering helper for other nodes
spapr: Refactor spapr_populate_memory() to allow memoryless nodes
spapr: Split memory nodes to power-of-two blocks
spapr: Add a helper for node0_size calculation
spapr: Fix ibm, associativity for memory nodes
spapr_pci: Fix config space corruption
Anton Blanchard (2):
spapr-vlan: Don't touch last entry in buffer list
hypervisor property clashes with hypervisor node
Benjamin Herrenschmidt (2):
loader: Add load_image_size() to replace load_image()
spapr: Locate RTAS and device-tree based on real RMA
Bharat Bhushan (4):
ppc: debug stub: Get trap instruction opcode from KVM
ppc: synchronize excp_vectors for injecting exception
ppc: Add software breakpoint support
ppc: Add hw breakpoint watchpoint support
Gonglei (1):
spapr: fix possible memory leak
Greg Kurz (1):
spapr_pci: map the MSI window in each PHB
Nikunj A Dadhania (3):
ppc: spapr-rtas - implement os-term rtas call
spapr: add uuid/host details to device tree
ppc/spapr: Fix MAX_CPUS to 255
Peter Maydell (1):
hw/ppc/spapr_hcall.c: Fix typo in function names
Tom Musta (20):
linux-user: Fix Stack Pointer Bug in PPC setup_rt_frame
linux-user: Split PPC Trampoline Encoding from Register Save
linux-user: Enable Signal Handlers on PPC64
linux-user: Properly Dereference PPC64 ELFv1 Signal Handler Pointer
linux-user: Implement do_setcontext for PPC64
linux-user: Handle PPC64 ELFv2 Function Pointers
target-ppc: Bug Fix: rlwinm
target-ppc: Bug Fix: rlwnm
target-ppc: Bug Fix: rlwimi
target-ppc: Bug Fix: mullwo
target-ppc: Bug Fix: mullw
target-ppc: Bug Fix: mulldo OV Detection
target-ppc: Bug Fix: srawi
target-ppc: Bug Fix: srad
target-ppc: Special Case of rlwimi Should Use Deposit
target-ppc: Optimize rlwinm MB=0 ME=31
target-ppc: Optimize rlwnm MB=0 ME=31
target-ppc: Clean Up mullw
target-ppc: Clean up mullwo
target-ppc: Implement mulldo with TCG
# gpg: Signature made Mon 08 Sep 2014 11:51:15 BST using RSA key ID 03FEDC60
# gpg: Can't check signature: public key not found
* remotes/agraf/tags/signed-ppc-for-upstream: (52 commits)
hypervisor property clashes with hypervisor node
PPC: Fix default config ordering and add eTSEC for ppc64
spapr_pci: map the MSI window in each PHB
target-ppc: Implement mulldo with TCG
target-ppc: Clean up mullwo
target-ppc: Clean Up mullw
target-ppc: Optimize rlwnm MB=0 ME=31
target-ppc: Optimize rlwinm MB=0 ME=31
target-ppc: Special Case of rlwimi Should Use Deposit
spapr-vlan: Don't touch last entry in buffer list
spapr_pci: Fix config space corruption
PPC: Cuda: Use cuda timer to expose tbfreq to guest
PPC: Mac: Move tbfreq into local variable
PPC: mac_nvram: Split NVRAM into OF and OSX parts
PPC: mac_nvram: Allow 2 and 4 byte accesses
PPC: mac_nvram: Remove unused functions
PPC: mac99: Fix core99 timer frequency
PPC: KVM: Use vm check_extension for pv hcall
KVM: Add helper to run KVM_CHECK_EXTENSION on vm fd
target-ppc: Bug Fix: srad
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
dtc fails on a recent QEMU snapshot:
ERROR (name_properties): "name" property in /hypervisor#1 is incorrect ("hypervisor" instead of base node name)
Looking at the device tree we have a hypervisor property:
# lsprop hypervisor
hypervisor "kvm"
But we also have a hypervisor node, with a name that doesn't match:
# lsprop hypervisor#1/
name "hypervisor"
compatible "linux,kvm"
linux,phandle 7e5eb5d8 (2120136152)
Commit c08ce91d309c (spapr: add uuid/host details to device tree)
looks to have collided with an earlier patch. Remove the hypervisor
property.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
On sPAPR, virtio devices are connected to the PCI bus and use MSI-X.
Commit cc943c36fa has modified MSI-X
so that writes are made using the bus master address space and follow
the IOMMU path.
Unfortunately, the IOMMU address space address space does not have an
MSI window: the notification is silently dropped in unassigned_mem_write
instead of reaching the guest... The most visible effect is that all
virtio devices are non-functional on sPAPR since then. :(
This patch does the following:
1) map the MSI window into the IOMMU address space for each PHB
- since each PHB instantiates its own IOMMU address space, we
can safely map the window at a fixed address (SPAPR_PCI_MSI_WINDOW)
- no real need to keep the MSI window setup in a separate function,
the spapr_pci_msi_init() code moves to spapr_phb_realize().
2) kill the global MSI window as it is not needed in the end
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The last 8 bytes of the buffer list is defined to contain the number
of dropped frames. At the moment we use it to store rx entries,
which trips up ethtool -S:
rx_no_buffer: 9223380832981355136
Fix this by skipping the last buffer list entry.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
