CPUPPCState includes fields htab_base and htab_mask which store the base
address (GPA) and size (as a mask) of the guest's hashed page table (HPT).
These are set when the SDR1 register is updated.
Keeping these in sync with the SDR1 is actually a little bit fiddly, and
probably not useful for performance, since keeping them expands the size of
CPUPPCState. It also makes some upcoming changes harder to implement.
This patch removes these fields, in favour of calculating them directly
from the SDR1 contents when necessary.
This does make a change to the behaviour of attempting to write a bad value
(invalid HPT size) to the SDR1 with an mtspr instruction. Previously, the
bad value would be stored in SDR1 and could be retrieved with a later
mfspr, but the HPT size as used by the softmmu would be, clamped to the
allowed values. Now, writing a bad value is treated as a no-op. An error
message is printed in both new and old versions.
I'm not sure which behaviour, if either, matches real hardware. I don't
think it matters that much, since it's pretty clear that if an OS writes
a bad value to SDR1, it's not going to boot.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Accesses to the hashed page table (HPT) are complicated by the fact that
the HPT could be in one of three places:
1) Within guest memory - when we're emulating a full guest CPU at the
hardware level (e.g. powernv, mac99, g3beige)
2) Within qemu, but outside guest memory - when we're emulating user and
supervisor instructions within TCG, but instead of emulating
the CPU's hypervisor mode, we just emulate a hypervisor's behaviour
(pseries in TCG or KVM-PR)
3) Within the host kernel - a pseries machine using KVM-HV
acceleration. Mostly accesses to the HPT are handled by KVM,
but there are a few cases where qemu needs to access it via a
special fd for the purpose.
In order to batch accesses to the fd in case (3), we use a somewhat awkward
ppc_hash64_start_access() / ppc_hash64_stop_access() pair, which for case
(3) reads / releases several HPTEs from the kernel as a batch (usually a
whole PTEG). For cases (1) & (2) it just returns an address value. The
actual HPTE load helpers then need to interpret the returned token
differently in the 3 cases.
This patch keeps the same basic structure, but simplfiies the details.
First start_access() / stop_access() are renamed to map_hptes() and
unmap_hptes() to make their operation more obvious. Second, map_hptes()
now always returns a qemu pointer, which can always be used in the same way
by the load_hpte() helpers. In case (1) it comes from address_space_map()
in case (2) directly from qemu's HPT buffer and in case (3) from a
temporary buffer read from the KVM fd.
While we're at it, make things a bit more consistent in terms of types and
variable names: avoid variables named 'index' (it shadows index(3) which
can lead to confusing results), use 'hwaddr ptex' for HPTE indices and
uint64_t for each of the HPTE words, use ptex throughout the call stack
instead of pte_offset in some places (we still need that at the bottom
layer, but nowhere else).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
At present the SDR1 register - the base of the system's hashed page table
(HPT) - is represented as an SPR with supervisor read and write permission.
However, on CPUs which have a hypervisor mode, the SDR1 is a hypervisor
only resource. Change the permission checking on the SPR to reflect this.
Now that this is done, we don't need to check for an external HPT executing
mtsdr1: an external HPT only applies when we're emulating the behaviour of
a hypervisor, rather than modelling the CPU's hypervisor mode internally,
so if we're permitted to execute mtsdr1, we don't have an external HPT.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
cpu_ppc_set_papr() sets up various aspects of CPU state for use with PAPR
paravirtualized guests. However, it doesn't set the virtual hypervisor,
so callers must also call cpu_ppc_set_vhyp() so that PAPR hypercalls are
handled properly. This is a bit silly, so fold setting the virtual
hypervisor into cpu_ppc_set_papr().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
* Standardize on 'ptex' instead of 'pte_index' for HPTE index variables
for consistency and brevity
* Avoid variables named 'index'; shadowing index(3) from libc can lead to
surprising bugs if the variable is removed, because compiler errors
might not appear for remaining references
* Clarify index calculations in h_enter() - we have two cases, H_EXACT
where the exact HPTE slot is given, and !H_EXACT where we search for
an empty slot within the hash bucket. Make the calculation more
consistent between the cases.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
When a 'pseries' guest is running with KVM-HV, the guest's hashed page
table (HPT) is stored within the host kernel, so it is not directly
accessible to qemu. Most of the time, qemu doesn't need to access it:
we're using the hardware MMU, and KVM itself implements the guest
hypercalls for manipulating the HPT.
However, qemu does need access to the in-KVM HPT to implement
get_phys_page_debug() for the benefit of the gdbstub, and maybe for
other debug operations.
To allow this, 7c43bca "target-ppc: Fix page table lookup with kvm
enabled" added kvmppc_hash64_read_pteg() to target/ppc/kvm.c to read
in a batch of HPTEs from the KVM table. Unfortunately, there are a
couple of problems with this:
First, the name of the function implies it always reads a whole PTEG
from the HPT, but in fact in some cases it's used to grab individual
HPTEs (which ends up pulling 8 HPTEs, not aligned to a PTEG from the
kernel).
Second, and more importantly, the code to read the HPTEs from KVM is
simply wrong, in general. The data from the fd that KVM provides is
designed mostly for compact migration rather than this sort of one-off
access, and so needs some decoding for this purpose. The current code
will work in some cases, but if there are invalid HPTEs then it will
not get sane results.
This patch rewrite the HPTE reading function to have a simpler
interface (just read n HPTEs into a caller provided buffer), and to
correctly decode the stream from the kernel.
For consistency we also clean up the similar function for altering
HPTEs within KVM (introduced in c138593 "target-ppc: Update
ppc_hash64_store_hpte to support updating in-kernel htab").
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Some systems can already provide more than 255 hardware threads.
Bumping the QEMU limit to 1024 seems reasonable:
- it has no visible overhead in top;
- the limit itself has no effect on hot paths.
Cc: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Removes duplicate code and will be useful for consolidating flags
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When DT node names for PCI devices are generated by SLOF,
they are generated according to the type of the device
(for instance, ethernet for virtio-net-pci device).
Node name for hotplugged devices is generated by QEMU.
This patch adds the mechanic to QEMU to create the node
name according to the device type too.
The data structure has been roughly copied from OpenBIOS/OpenHackware,
node names from SLOF.
Example:
Hotplugging some PCI cards with QEMU monitor:
device_add virtio-tablet-pci
device_add virtio-serial-pci
device_add virtio-mouse-pci
device_add virtio-scsi-pci
device_add virtio-gpu-pci
device_add ne2k_pci
device_add nec-usb-xhci
device_add intel-hda
What we can see in linux device tree:
for dir in /proc/device-tree/pci@800000020000000/*@*/; do
echo $dir
cat $dir/name
echo
done
WITHOUT this patch:
/proc/device-tree/pci@800000020000000/pci@0/
pci
/proc/device-tree/pci@800000020000000/pci@1/
pci
/proc/device-tree/pci@800000020000000/pci@2/
pci
/proc/device-tree/pci@800000020000000/pci@3/
pci
/proc/device-tree/pci@800000020000000/pci@4/
pci
/proc/device-tree/pci@800000020000000/pci@5/
pci
/proc/device-tree/pci@800000020000000/pci@6/
pci
/proc/device-tree/pci@800000020000000/pci@7/
pci
WITH this patch:
/proc/device-tree/pci@800000020000000/communication-controller@1/
communication-controller
/proc/device-tree/pci@800000020000000/display@4/
display
/proc/device-tree/pci@800000020000000/ethernet@5/
ethernet
/proc/device-tree/pci@800000020000000/input-controller@0/
input-controller
/proc/device-tree/pci@800000020000000/mouse@2/
mouse
/proc/device-tree/pci@800000020000000/multimedia-device@7/
multimedia-device
/proc/device-tree/pci@800000020000000/scsi@3/
scsi
/proc/device-tree/pci@800000020000000/usb-xhci@6/
usb-xhci
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To allow QEMU to add PCI entries in device tree,
we must have a more exhaustive list of PCI class IDs.
This patch synchronizes as much as possible with
pci_ids.h and add some missing IDs from SLOF.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since commit b0a335e351, a socket write
may trigger a disconnect events, calling vhost_user_stop() and clearing
all the vhost_dev strutures holding data that vhost.c functions expect
to remain valid. Delay the cleanup to keep the vhost_dev structure
valid during the vhost.c functions.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20170227104956.24729-1-marcandre.lureau@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- a fix to a minor bug reported by Coverity
- throttling support in the local backend (command line only)
-----BEGIN PGP SIGNATURE-----
iEYEABECAAYFAli1Q64ACgkQAvw66wEB28I5yQCePbLPSOtHO4LJGc2E973L7vH2
hQIAnReLFevyNN6BpivucP2/0YmAIKSi
=uTYd
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/gkurz/tags/for-upstream' into staging
This pull request brings:
- a fix to a minor bug reported by Coverity
- throttling support in the local backend (command line only)
# gpg: Signature made Tue 28 Feb 2017 09:32:30 GMT
# gpg: using DSA key 0x02FC3AEB0101DBC2
# gpg: Good signature from "Greg Kurz <groug@kaod.org>"
# gpg: aka "Greg Kurz <groug@free.fr>"
# gpg: aka "Greg Kurz <gkurz@linux.vnet.ibm.com>"
# gpg: aka "Gregory Kurz (Groug) <groug@free.fr>"
# gpg: aka "[jpeg image of size 3330]"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 2BD4 3B44 535E C0A7 9894 DBA2 02FC 3AEB 0101 DBC2
* remotes/gkurz/tags/for-upstream:
throttle: factor out duplicate code
fsdev: add IO throttle support to fsdev devices
9pfs: fix v9fs_lock error case
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* raspi2: implement RNG module
* raspi2: implement new SD card controller (but don't wire it up)
* sdhci: bugfixes for block transfers
* virt: fix cpu object reference leak
* Add missing fp_access_check() to aarch64 crypto instructions
* cputlb: Don't assume do_unassigned_access() never returns
* virt: Add a user option to disallow ITS instantiation
* i.MX timers: fix reset handling
* ARMv7M NVIC: rewrite to fix broken priority handling and masking
* exynos: Fix proper mapping of CPUs by providing real cluster ID
* exynos: Fix Linux kernel division by zero for PLLs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3qLp
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20170228' into staging
target-arm queue:
* raspi2: implement RNG module
* raspi2: implement new SD card controller (but don't wire it up)
* sdhci: bugfixes for block transfers
* virt: fix cpu object reference leak
* Add missing fp_access_check() to aarch64 crypto instructions
* cputlb: Don't assume do_unassigned_access() never returns
* virt: Add a user option to disallow ITS instantiation
* i.MX timers: fix reset handling
* ARMv7M NVIC: rewrite to fix broken priority handling and masking
* exynos: Fix proper mapping of CPUs by providing real cluster ID
* exynos: Fix Linux kernel division by zero for PLLs
# gpg: Signature made Tue 28 Feb 2017 12:40:51 GMT
# gpg: using RSA key 0x3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20170228: (27 commits)
hw/arm/exynos: Fix proper mapping of CPUs by providing real cluster ID
hw/arm/exynos: Fix Linux kernel division by zero for PLLs
bcm2835_sdhost: add bcm2835 sdhost controller
armv7m: Allow SHCSR writes to change pending and active bits
armv7m: Raise correct kind of UsageFault for attempts to execute ARM code
armv7m: Check exception return consistency
armv7m: Extract "exception taken" code into functions
armv7m: VECTCLRACTIVE and VECTRESET are UNPREDICTABLE
armv7m: Simpler and faster exception start
armv7m: Remove unused armv7m_nvic_acknowledge_irq() return value
armv7m: Escalate exceptions to HardFault if necessary
arm: gic: Remove references to NVIC
armv7m: Fix condition check for taking exceptions
armv7m: Rewrite NVIC to not use any GIC code
armv7m: Implement reading and writing of PRIGROUP
armv7m: Rename nvic_state to NVICState
ARM i.MX timers: fix reset handling
hw/arm/virt: Add a user option to disallow ITS instantiation
cputlb: Don't assume do_unassigned_access() never returns
Add missing fp_access_check() to aarch64 crypto instructions
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Exynos4210 has cluster ID 0x9 in its MPIDR register (raw value
0x8000090x). If this cluster ID is not provided, then Linux kernel
cannot map DeviceTree nodes to MPIDR values resulting in kernel
warning and lack of any secondary CPUs:
DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
...
smp: Bringing up secondary CPUs ...
smp: Brought up 1 node, 1 CPU
SMP: Total of 1 processors activated (24.00 BogoMIPS).
Provide a cluster ID so Linux will see proper MPIDR and will try to
bring the secondary CPU online.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Message-id: 20170226200142.31169-2-krzk@kernel.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Without any clock controller, the Linux kernel was hitting division by
zero during boot or with clk_summary:
[ 0.000000] [<c031054c>] (unwind_backtrace) from [<c030ba6c>] (show_stack+0x10/0x14)
[ 0.000000] [<c030ba6c>] (show_stack) from [<c05b2660>] (dump_stack+0x88/0x9c)
[ 0.000000] [<c05b2660>] (dump_stack) from [<c05b11a4>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c05b11a4>] (Ldiv0) from [<c06ad1e0>] (samsung_pll45xx_recalc_rate+0x58/0x74)
[ 0.000000] [<c06ad1e0>] (samsung_pll45xx_recalc_rate) from [<c0692ec0>] (clk_register+0x39c/0x63c)
[ 0.000000] [<c0692ec0>] (clk_register) from [<c125d360>] (samsung_clk_register_pll+0x2e0/0x3d4)
[ 0.000000] [<c125d360>] (samsung_clk_register_pll) from [<c125d7e8>] (exynos4_clk_init+0x1b0/0x5e4)
[ 0.000000] [<c125d7e8>] (exynos4_clk_init) from [<c12335f4>] (of_clk_init+0x17c/0x210)
[ 0.000000] [<c12335f4>] (of_clk_init) from [<c1204700>] (time_init+0x24/0x2c)
[ 0.000000] [<c1204700>] (time_init) from [<c1200b2c>] (start_kernel+0x24c/0x38c)
[ 0.000000] [<c1200b2c>] (start_kernel) from [<4020807c>] (0x4020807c)
Provide stub for clock controller returning reset values for PLLs.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Message-id: 20170226200142.31169-1-krzk@kernel.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds the BCM2835 SDHost controller from Arasan.
Signed-off-by: Clement Deschamps <clement.deschamps@antfield.fr>
Message-id: 20170224164021.9066-2-clement.deschamps@antfield.fr
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the NVIC SHCSR write behaviour which allows pending and
active status of some exceptions to be changed.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
M profile doesn't implement ARM, and the architecturally required
behaviour for attempts to execute with the Thumb bit clear is to
generate a UsageFault with the CFSR INVSTATE bit set. We were
incorrectly implementing this as generating an UNDEFINSTR UsageFault;
fix this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Implement the exception return consistency checks
described in the v7M pseudocode ExceptionReturn().
Inspired by a patch from Michael Davidsaver's series, but
this is a reimplementation from scratch based on the
ARM ARM pseudocode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Extract the code from the tail end of arm_v7m_do_interrupt() which
enters the exception handler into a pair of utility functions
v7m_exception_taken() and v7m_push_stack(), which correspond roughly
to the pseudocode PushStack() and ExceptionTaken().
This also requires us to move the arm_v7m_load_vector() utility
routine up so we can call it.
Handling illegal exception returns has some cases where we want to
take a UsageFault either on an existing stack frame or with a new
stack frame but with a specific LR value, so we want to be able to
call these without having to go via arm_v7m_cpu_do_interrupt().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The VECTCLRACTIVE and VECTRESET bits in the AIRCR are both
documented as UNPREDICTABLE if you write a 1 to them when
the processor is not halted in Debug state (ie stopped
and under the control of an external JTAG debugger).
Since we don't implement Debug state or emulated JTAG
these bits are always UNPREDICTABLE for us. Instead of
logging them as unimplemented we can simply log writes
as guest errors and ignore them.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
[PMM: change extracted from another patch; commit message
constructed from scratch]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
All the places in armv7m_cpu_do_interrupt() which pend an
exception in the NVIC are doing so for synchronous
exceptions. We know that we will always take some
exception in this case, so we can just acknowledge it
immediately, rather than returning and then immediately
being called again because the NVIC has raised its outbound
IRQ line.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
[PMM: tweaked commit message; added DEBUG to the set of
exceptions we handle immediately, since it is synchronous
when it results from the BKPT instruction]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Having armv7m_nvic_acknowledge_irq() return the new value of
env->v7m.exception and its one caller assign the return value
back to env->v7m.exception is pointless. Just make the return
type void instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The v7M exception architecture requires that if a synchronous
exception cannot be taken immediately (because it is disabled
or at too low a priority) then it should be escalated to
HardFault (and the HardFault exception is then taken).
Implement this escalation logic.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
[PMM: extracted from another patch]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Now that the NVIC is its own separate implementation, we can
clean up the GIC code by removing REV_NVIC and conditionals
which use it.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The M profile condition for when we can take a pending exception or
interrupt is not the same as that for A/R profile. The code
originally copied from the A/R profile version of the
cpu_exec_interrupt function only worked by chance for the
very simple case of exceptions being masked by PRIMASK.
Replace it with a call to a function in the NVIC code that
correctly compares the priority of the pending exception
against the current execution priority of the CPU.
[Michael Davidsaver's patchset had a patch to do something
similar but the implementation ended up being a rewrite.]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Despite some superficial similarities of register layout, the
M-profile NVIC is really very different from the A-profile GIC.
Our current attempt to reuse the GIC code means that we have
significant bugs in our NVIC.
Implement the NVIC as an entirely separate device, to give
us somewhere we can get the behaviour correct.
This initial commit does not attempt to implement exception
priority escalation, since the GIC-based code didn't either.
It does fix a few bugs in passing:
* ICSR.RETTOBASE polarity was wrong and didn't account for
internal exceptions
* ICSR.VECTPENDING was 16 too high if the pending exception
was for an external interrupt
* UsageFault, BusFault and MemFault were not disabled on reset
as they are supposed to be
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
[PMM: reworked, various bugs and stylistic cleanups]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Add a state field for the v7M PRIGROUP register and implent
reading and writing it. The current NVIC doesn't honour
the values written, but the new version will.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Rename the nvic_state struct to NVICState, to match
our naming conventions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The i.MX timer device can be reset by writing to the SWR bit
of the CR register. This has to behave differently from hard
(power-on) reset because it does not reset all of the bits
in the CR register.
We were incorrectly implementing soft reset and hard reset
the same way, and in addition had a logic error which meant
that we were clearing the bits that soft-reset is supposed
to preserve and not touching the bits that soft-reset clears.
This was not correct behaviour for either kind of reset.
Separate out the soft reset and hard reset code paths, and
correct the handling of reset of the CR register so that it
is correct in both cases.
Signed-off-by: Kurban Mallachiev <mallachiev@ispras.ru>
[PMM: rephrased commit message, spacing on operators;
use bool rather than int for is_soft_reset]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In 2.9 ITS will block save/restore and migration use cases. As such,
let's introduce a user option that allows to turn its instantiation
off, along with GICv3. With the "its" option turned false, migration
will be possible, obviously at the expense of MSI support (with GICv3).
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1487681108-14452-1-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In get_page_addr_code(), if the guest PC doesn't correspond to RAM
then we currently run the CPU's do_unassigned_access() hook if it has
one, and otherwise we give up and exit QEMU with a more-or-less
useful message. This code assumes that the do_unassigned_access hook
will never return, because if it does then we'll plough on attempting
to use a non-RAM TLB entry to get a RAM address and will abort() in
qemu_ram_addr_from_host_nofail(). Unfortunately some CPU
implementations of this hook do return: Microblaze, SPARC and the ARM
v7M.
Change the code to call report_bad_exec() if the hook returns, as
well as if it didn't have one. This means we can tidy it up to use
the cpu_unassigned_access() function which wraps the "get the CPU
class and call the hook if it has one" work, since we aren't trying
to distinguish "no hook" from "hook existed and returned" any more.
This brings the handling of this hook into line with the handling
used for data accesses, where "hook returned" is treated the
same as "no hook existed" and gets you the default behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
The aarch64 crypto instructions for AES and SHA are missing the
check for if the FPU is enabled.
Signed-off-by: Nick Reilly <nreilly@blackberry.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
object_new(FOO) returns an object with ref_cnt == 1
and following
object_property_set_bool(cpuobj, true, "realized", NULL)
set parent of cpuobj to '/machine/unattached' which makes
ref_cnt == 2.
Since machvirt_init() doesn't take ownership of cpuobj
returned by object_new() it should explicitly drop
reference to cpuobj when dangling pointer is about to
go out of scope like it's done pc_new_cpu() to avoid
object leak.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 1487253461-269218-1-git-send-email-imammedo@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In SDHCI protocol, the 'Block count enable' bit of the Transfer
Mode register is relevant only in multi block transfers. We need
not check it in single block transfers.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 20170214185225.7994-5-ppandit@redhat.com
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In sdhci_write invoke multi block transfer if it is enabled
in the transfer mode register 's->trnmod'.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 20170214185225.7994-4-ppandit@redhat.com
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the SDHCI protocol, the transfer mode register value
is used during multi block transfer to check if block count
register is enabled and should be updated. Transfer mode
register could be set such that, block count register would
not be updated, thus leading to an infinite loop. Add check
to avoid it.
Reported-by: Wjjzhang <wjjzhang@tencent.com>
Reported-by: Jiang Xin <jiangxin1@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 20170214185225.7994-3-ppandit@redhat.com
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In SDHCI protocol, the transfer mode register is defined
to be of 6 bits. Mask its value with '0x0037' so that an
invalid value could not be assigned.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20170214185225.7994-2-ppandit@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch to using qcrypto_random_bytes() rather than rand() as
our source of randomness for the BCM2835 RNG.
If qcrypto_random_bytes() fails, we don't want to return the guest a
non-random value in case they're really using it for cryptographic
purposes, so the best we can do is a fatal error. This shouldn't
happen unless something's broken, though.
In theory we could implement this device's full FIFO and interrupt
semantics and then just stop filling the FIFO. That's a lot of work,
though, and doesn't really give a very nice diagnostic to the user
since the guest will just seem to hang.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Recent vanilla Raspberry Pi kernels started to make use of
the hardware random number generator in BCM2835 SoC. As a
result, those kernels wouldn't work anymore under QEMU
but rather just freeze during the boot process.
This patch implements a trivial BCM2835 compatible RNG,
and adds it as a peripheral to BCM2835 platform, which
allows to boot a vanilla Raspberry Pi kernel under Qemu.
Changes since v1:
* Prevented guest from writing [31..20] bits in rng_status
* Removed redundant minimum_version_id_old
* Added field entries for the state
* Changed realize function to reset
Signed-off-by: Marcin Chojnacki <marcinch7@gmail.com>
Message-id: 20170210210857.47893-1-marcinch7@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch removes the redundant throttle code that was present in
block and fsdev device files. Now the common code is moved
to a single file.
Signed-off-by: Pradeep Jagadeesh <pradeep.jagadeesh@huawei.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
(fix indent nit, Greg Kurz)
Signed-off-by: Greg Kurz <groug@kaod.org>
This patchset adds the throttle support for the 9p-local driver.
For now this functionality can be enabled only through qemu cli options.
QMP interface and support to other drivers need further extensions.
To make it simple for other 9p drivers, the throttle code has been put in
separate files.
Signed-off-by: Pradeep Jagadeesh <pradeep.jagadeesh@huawei.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
(pass extra NULL CoMutex * argument to qemu_co_queue_wait(),
added options to qemu-options.hx, Greg Kurz)
Signed-off-by: Greg Kurz <groug@kaod.org>
In this case, we are marshaling an error status instead of the errno value.
Reorganize the out and out_nofid labels to look like all the other cases.
Coverity reports this because the "err = -ENOENT" and "err = -EINVAL"
assignments above are dead, overwritten by the call to pdu_marshal.
(Coverity issues CID1348512 and CID1348513)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(also open-coded the success path since locking is a nop for us, Greg Kurz)
Signed-off-by: Greg Kurz <groug@kaod.org>
iQEcBAABAgAGBQJYtFTTAAoJEJykq7OBq3PI93wH/RkY2roxr0WB+uJu/cWnMPFX
kuTsx8xJOImRJWuVaHMeMewbF5P3KoppDpn6V2MiJTCBgLO3sYWpN0zd9w3WyOcd
qOA+WjPxJvj4ttkiIAJEzcka7aStyCKSDNFZeMQi0mJRjjclrfaH84ICGEvDmPEO
qeqA714jnsDewwUtTy6fUOdqVZXTXdVWv+kR0er2ovNHbmEzc8uDaw624PBOZgjN
eg3Tny9z77hP3QTlqmhKr9I2gvWDj1fyBd0Bra9dByuc8vsTTehYX6qIbjRvWKsU
bIdTQOM1NVjUo5QI8fpk9X4BNWU6b5rjQ6dYEfgN3fFHF33QKwanmyWX0ivDJ5s=
=Pvt5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/block-pull-request' into staging
# gpg: Signature made Mon 27 Feb 2017 16:33:23 GMT
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/block-pull-request:
tests-aio-multithread: use atomic_read properly
iscsi: do not use aio_context_acquire/release
nfs: do not use aio_context_acquire/release
curl: do not use aio_context_acquire/release
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
