Commit Graph

485 Commits

Author SHA1 Message Date
Paolo Bonzini e351b82611 hw: Add support for LSI SAS1068 (mptsas) device
This adds the SAS1068 device, a SAS disk controller used in VMware that
is oldish but widely supported and has decent performance.  Unlike
megasas, it presents itself as a SAS controller and not as a RAID
controller.  The device corresponds to the mptsas kernel driver in
Linux.

A few small things in the device setup are based on Don Slutz's old
patch, but the device emulation was written from scratch based on Don's
SeaBIOS patch and on the FreeBSD and Linux drivers.  It is 2400 lines
shorter than Don's patch (and roughly the same size as MegaSAS---also
because it doesn't support the similar SPI controller), implements SCSI
task management functions (with asynchronous cancellation), supports
big-endian hosts, has complete support for migration and follows the
QEMU coding standards much more closely.

To write the driver, I first split Don's patch in two parts, with
the configuration bits in one file and the rest in a separate file.
I first left mptconfig.c in place and rewrote the rest, then deleted
mptconfig.c as well.  The configuration pages are still based mostly on
VirtualBox's, though not exactly the same.  However, the implementation
is completely different.  The contents of the pages themselves should
not be copyrightable.

Signed-off-by: Don Slutz <Don@CloudSwitch.com>
Message-Id: <1347382813-5662-1-git-send-email-Don@CloudSwitch.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2016-02-09 15:45:26 +01:00
Alex Williamson 95239e1625 vfio/pci: Lazy PBA emulation
The PCI spec recommends devices use additional alignment for MSI-X
data structures to allow software to map them to separate processor
pages.  One advantage of doing this is that we can emulate those data
structures without a significant performance impact to the operation
of the device.  Some devices fail to implement that suggestion and
assigned device performance suffers.

One such case of this is a Mellanox MT27500 series, ConnectX-3 VF,
where the MSI-X vector table and PBA are aligned on separate 4K
pages.  If PBA emulation is enabled, performance suffers.  It's not
clear how much value we get from PBA emulation, but the solution here
is to only lazily enable the emulated PBA when a masked MSI-X vector
fires.  We then attempt to more aggresively disable the PBA memory
region any time a vector is unmasked.  The expectation is then that
a typical VM will run entirely with PBA emulation disabled, and only
when used is that emulation re-enabled.

Reported-by: Shyam Kaushik <shyam.kaushik@gmail.com>
Tested-by: Shyam Kaushik <shyam.kaushik@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
2016-01-19 11:33:42 -07:00
Mark Cave-Ayland c6daed8654 trace: fix PRIx64 constants in trace-events
Commit c8ee0a4 introduced new events containing PRIx64 constants without
including the % prefix in the preceding string. This results in a compile
error during build if --enable-trace-backends is passed to configure.

Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 1450566522-6003-1-git-send-email-mark.cave-ayland@ilande.co.uk
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2016-01-07 09:39:11 +08:00
Qinghua Jin 67a9faccef trace: reflect the file name change
Some functions was moved from block.c to block/io.c, so the trace-events file should reflect that change.

Signed-off-by: Qinghua Jin <qhjin_dev@163.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2016-01-07 09:39:11 +08:00
Daniel P. Berrange 195e14d026 io: add QIOChannelCommand class
Add a QIOChannel subclass that is capable of performing I/O
to/from a separate process, via a pair of pipes. The command
can be used for unidirectional or bi-directional I/O.

Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
2015-12-18 12:18:31 +00:00
Daniel P. Berrange 2d1d0e70cf io: add QIOChannelWebsock class
Add a QIOChannel subclass that can run the websocket protocol over
the top of another QIOChannel instance. This initial implementation
is only capable of acting as a websockets server. There is no support
for acting as a websockets client yet.

Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
2015-12-18 12:18:31 +00:00
Daniel P. Berrange ed8ee42c40 io: add QIOChannelTLS class
Add a QIOChannel subclass that can run the TLS protocol over
the top of another QIOChannel instance. The object provides a
simplified API to perform the handshake when starting the TLS
session. The layering of TLS over the underlying channel does
not have to be setup immediately. It is possible to take an
existing QIOChannel that has done some handshake and then swap
in the QIOChannelTLS layer. This allows for use with protocols
which start TLS right away, and those which start plain text
and then negotiate TLS.

Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
2015-12-18 12:18:31 +00:00
Daniel P. Berrange d6e48869a4 io: add QIOChannelFile class
Add a QIOChannel subclass that is capable of operating on things
that are files, such as plain files, pipes, character/block
devices, but notably not sockets.

Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
2015-12-18 12:18:31 +00:00
Daniel P. Berrange 559607ea17 io: add QIOChannelSocket class
Implement a QIOChannel subclass that supports sockets I/O.
The implementation is able to manage a single socket file
descriptor, whether a TCP/UNIX listener, TCP/UNIX connection,
or a UDP datagram. It provides APIs which can listen and
connect either asynchronously or synchronously. Since there
is no asynchronous DNS lookup API available, it uses the
QIOTask helper for spawning a background thread to ensure
non-blocking operation.

Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
2015-12-18 12:18:31 +00:00
Daniel P. Berrange b02db2d920 io: add QIOTask class for async operations
A number of I/O operations need to be performed asynchronously
to avoid blocking the main loop. The caller of such APIs need
to provide a callback to be invoked on completion/error and
need access to the error, if any. The small QIOTask provides
a simple framework for dealing with such probes. The API
docs inline provide an outline of how this is to be used.

Some functions don't have the ability to run asynchronously
(eg getaddrinfo always blocks), so to facilitate their use,
the task class provides a mechanism to run a blocking
function in a thread, while triggering the completion
callback in the main event loop thread. This easily allows
any synchronous function to be made asynchronous, albeit
at the cost of spawning a thread.

In this series, the QIOTask class will be used for things like
the TLS handshake, the websockets handshake and TCP connect()
progress.

The concept of QIOTask is inspired by the GAsyncResult
interface / GTask class in the GIO libraries. The min
version requirements on glib don't allow those to be
used from QEMU, so QIOTask provides a facsimilie which
can be easily switched to GTask in the future if the
min version is increased.

Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
2015-12-18 12:18:30 +00:00
Paolo Bonzini c8ee0a445a linux-user: convert DEBUG_SIGNAL logging to tracepoints
"Unimplemented" messages go to stderr, everything else goes to tracepoints

Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-12-17 17:33:48 +01:00
Paolo Bonzini c6ce9f176f alpha: convert "naked" qemu_log to tracepoint
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-12-17 17:33:47 +01:00
Peter Maydell 98557acf92 fw_cfg: doc updates, various optimizations.
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iQIcBAABAgAGBQJWcnl0AAoJEEy22O7T6HE4vhgP/AxlVRTQ1vg1AhHPHuTmXLmq
 tS5m2FF73yzfy2eBDd2Vm3z1vdwmhbcZbV745dLLzVMaaFGmHSCbUQFnGPCCNdKt
 yXZkVh1Aqj2rR//Mmn293JWwVJq04LtGIXQxPMXO7m88fcdQ8PHiwyAVPUsV+6DY
 lLWxhtTTYeHb9xngIKnW7nSbL2OZUD49s0vwYb9w3Ih97cPFOBjBYiv3WowI9y48
 /fDb1POzV0/bVyhKvlkWfkDpZqF1ilob3v3zq2VniTkm5+wGmVIhlFwI6nGJNtne
 +aYrZgQSzsFjByrqWxfCIyp91e7+SEctDqtZZw1DA1gn01ksFvrX9Kz5UJTcXQw3
 eDhyxVnssjrakDR3KAEoIMroQPsrBT79pr7cRfyt0wqEfZ7p1kxH/iuyS+ZTCoST
 xVdM2HxzV7Qabo2iPQBeCu47Vbu8ON9prypM9BHegGFcS11zcLEIOTHTlrC0zO1U
 TqYpls1Nm+B0SfVgN7NkBNm+vj5321Qf/I+O8Gvtxks6AkspJMcbld8SX0xUiVQE
 VNos1DReR4CLh6Yc9UgmZAtdfzyCci8cpCrB2N5B/+AzLQetmrRnPXDBNCx2fTOB
 gkQpHsrlxDOZugF6ljt9y5vD9U+HhlTuZRmNCLoz92YMj3j+I1kcClA/JAjRz1UD
 kSDhSKsPTTf8xkemdZCp
 =7yKy
 -----END PGP SIGNATURE-----

Merge remote-tracking branch 'remotes/kraxel/tags/pull-fw-cfg-20151217-1' into staging

fw_cfg: doc updates, various optimizations.

# gpg: Signature made Thu 17 Dec 2015 08:59:32 GMT using RSA key ID D3E87138
# gpg: Good signature from "Gerd Hoffmann (work) <kraxel@redhat.com>"
# gpg:                 aka "Gerd Hoffmann <gerd@kraxel.org>"
# gpg:                 aka "Gerd Hoffmann (private) <kraxel@gmail.com>"

* remotes/kraxel/tags/pull-fw-cfg-20151217-1:
  fw_cfg: replace ioport data read with generic method
  fw_cfg: add generic non-DMA read method
  fw_cfg: avoid calculating invalid current entry pointer
  fw_cfg: remove offset argument from callback prototype
  fw_cfg: amend callback behavior spec to once per select
  fw_cfg: move internal function call docs to header file

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2015-12-17 12:40:07 +00:00
Gabriel L. Somlo 38bf20931a fw_cfg: add generic non-DMA read method
Introduce fw_cfg_data_read(), a generic read method which works
on all access widths (1 through 8 bytes, inclusive), and can be
used during both IOPort and MMIO read accesses.

To maintain legibility, only fw_cfg_data_mem_read() (the MMIO
data read method) is replaced by this patch. The new method
essentially unwinds the fw_cfg_data_mem_read() + fw_cfg_read()
combo, but without unnecessarily repeating all the validity
checks performed by the latter on each byte being read.

This patch also modifies the trace_fw_cfg_read prototype to
accept a 64-bit value argument, allowing it to work properly
with the new read method, but also remain backward compatible
with existing call sites.

Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Marc Marí <markmb@redhat.com>
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 1446733972-1602-6-git-send-email-somlo@cmu.edu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
2015-12-15 11:45:59 +01:00
Bandan Das 8e3e3897ce usb-mtp: Add support for inotify based file monitoring
For now, we use inotify watches to track only a small number of
events, namely, add, delete and modify. Note that for delete, the kernel
already deactivates the watch for us and we just need to
take care of modifying our internal state.

inotify is a linux only mechanism.

Suggested-by: Gerd Hoffman <kraxel@redhat.com>
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 1448314625-3855-4-git-send-email-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
2015-12-15 09:26:10 +01:00
Bandan Das 4c7a67f5cd usb-mtp: use a list for keeping track of children
To support adding/removal of objects, we will need to update
the object cache hierarchy we have built internally. Convert
to using a Qlist for easier management.

Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 1448314625-3855-2-git-send-email-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
2015-12-15 09:25:27 +01:00
Fam Zheng 61408b250e block: Don't wait serialising for non-COR read requests
The assertion problem was noticed in 06c3916b35, but it wasn't
completely fixed, because even though the req is not marked as
serialising, it still gets serialised by wait_serialising_requests
against other serialising requests, which could lead to the same
assertion failure.

Fix it by even more explicitly skipping the serialising for this
specific case.

Signed-off-by: Fam Zheng <famz@redhat.com>
Message-id: 1448962590-2842-2-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2015-12-03 11:08:07 +08:00
Peter Maydell c27e9014d5 vnc: buffer code improvements, bugfixes.
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iQIcBAABAgAGBQJWShBCAAoJEEy22O7T6HE4/L4P/j2do44O18ni7OfloXQvCa5q
 xI21F/FqWZvpNVQnuhkFaBP8j9ggHIaKHJCMzQqSTs/ub+izKvsgFVWu5M9NAMPx
 OOhT20enigsBxP/WPrpjUknrMmjcnEXfYQfRhVREOZCkak95jfP8cLEAg1W81ehf
 /xS5TAJtGkxpxhQNpv94jXV5WdJmBYtKSUfUtHaEA2mgUeUrvUYlCQUUJrb23foG
 2LKGiv1GMqtNGHtl+uvBBc4XDdRrBR2iMgjjhj6IWniDCL2uxHojEN+Z23d1ldSK
 DXnNvoCVb5qzhSVVxJW34P0V2WJ8fClc0gvMWxtOvA4vLn/jnJw/Ig2MV1n4iQNu
 6vm3ZUUbz4f18eB63xy35AN4C63YgZ5xduGQ55HVMyMUtcyxkNv4SFA4NEY8Osj3
 Iy1TR+zXvdjH3d4K26J/s8/Lc1MVWlvGw6JzQn6gCF5x4ig8uKbA89S19skNw0Fe
 IXm5qHjUNNRwzG6/eGB1xpNz4O+yqGXfBAErsb0IbLBUdlweGLCZHvek2FCOUWiF
 7DY+dutFSW+nRjdOEKbRsHZL7ENB6vMzXFD3RH/EzWyvjveYl2yj2CshvHhBWxcx
 B4us35hQd7+KnkbcOQAcq5hxeXN9ZxLXjuOVB/3he+blH9uVPWo4BX6bQ71sXUpa
 kgIsPhzxCo+Bto/7P93F
 =oNDV
 -----END PGP SIGNATURE-----

Merge remote-tracking branch 'remotes/kraxel/tags/pull-vnc-20151116-1' into staging

vnc: buffer code improvements, bugfixes.

# gpg: Signature made Mon 16 Nov 2015 17:20:02 GMT using RSA key ID D3E87138
# gpg: Good signature from "Gerd Hoffmann (work) <kraxel@redhat.com>"
# gpg:                 aka "Gerd Hoffmann <gerd@kraxel.org>"
# gpg:                 aka "Gerd Hoffmann (private) <kraxel@gmail.com>"

* remotes/kraxel/tags/pull-vnc-20151116-1:
  vnc: fix mismerge
  buffer: allow a buffer to shrink gracefully
  buffer: factor out buffer_adj_size
  buffer: factor out buffer_req_size
  vnc: recycle empty vs->output buffer
  vnc: fix local state init
  vnc: only alloc server surface with clients connected
  vnc: use vnc_{width,height} in vnc_set_area_dirty
  vnc: factor out vnc_update_server_surface
  vnc: add vnc_width+vnc_height helpers
  vnc: zap dead code
  vnc-jobs: move buffer reset, use new buffer move
  vnc: kill jobs queue buffer
  vnc: attach names to buffers
  buffer: add tracing
  buffer: add buffer_shrink
  buffer: add buffer_move
  buffer: add buffer_move_empty
  buffer: add buffer_init
  buffer: make the Buffer capacity increase in powers of two

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2015-11-17 12:34:07 +00:00
Dr. David Alan Gilbert e9bef235d9 End of migration for postcopy
Tweak the end of migration cleanup; we don't want to close stuff down
at the end of the main stream, since the postcopy is still sending pages
on the other thread.

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:28 +01:00
Dr. David Alan Gilbert f952710757 Postcopy: Mark nohugepage before discard
Prior to servicing userfault requests we must ensure we've not got
huge pages in the area that might include non-transferred memory,
since a hugepage could incorrectly mark the whole huge page as present.

We mark the area as non-huge page (nhp) just before we perform
discards; the discard code now tells us to discard any areas
that haven't been sent (as well as any that are redirtied);
any already formed transparent-huge-pages get fragmented
by this discard process if they cotnain any discards.

Transparent huge pages that have been entirely transferred
and don't contain any discards are not broken by this mechanism;
they stay as huge pages.

By starting postcopy after a full precopy pass, many of the pages
then stay as huge pages; this is important for maintaining performance
after the end of the migration.

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:28 +01:00
Dr. David Alan Gilbert 27c6825bd3 postcopy: Wire up loadvm_postcopy_handle_ commands
Wire up more of the handlers for the commands on the destination side,
in particular loadvm_postcopy_handle_run now has enough to start the
guest running.

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:28 +01:00
Dr. David Alan Gilbert c76201ab52 Start up a postcopy/listener thread ready for incoming page data
The loading of a device state (during postcopy) may access guest
memory that's still on the source machine and thus might need
a page fill; split off a separate thread that handles the incoming
page data so that the original incoming migration code can finish
off the device data.

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:28 +01:00
Dr. David Alan Gilbert c4faeed231 Postcopy; Handle userfault requests
userfaultfd is a Linux syscall that gives an fd that receives a stream
of notifications of accesses to pages registered with it and allows
the program to acknowledge those stalls and tell the accessing
thread to carry on.

We convert the requests from the kernel into messages back to the
source asking for the pages.

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:28 +01:00
Dr. David Alan Gilbert a71808772a Postcopy: Use helpers to map pages during migration
In postcopy, the destination guest is running at the same time
as it's receiving pages; as we receive new pages we must put
them into the guests address space atomically to avoid a running
CPU accessing a partially written page.

Use the helpers in postcopy-ram.c to map these pages.

qemu_get_buffer_in_place is used to avoid a copy out of qemu_file
in the case that postcopy is going to do a copy anyway.

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:27 +01:00
Dr. David Alan Gilbert 696ed9a9b3 postcopy_ram.c: place_page and helpers
postcopy_place_page (etc) provide a way for postcopy to place a page
into guests memory atomically (using the copy ioctl on the ufd).

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:27 +01:00
Dr. David Alan Gilbert a82d593b61 Page request: Consume pages off the post-copy queue
When transmitting RAM pages, consume pages that have been queued by
MIG_RPCOMM_REQPAGE commands and send them ahead of normal page scanning.

Note:
  a) After a queued page the linear walk carries on from after the
unqueued page; there is a reasonable chance that the destination
was about to ask for other closeby pages anyway.

  b) We have to be careful of any assumptions that the page walking
code makes, in particular it does some short cuts on its first linear
walk that break as soon as we do a queued page.

  c) We have to be careful to not break up host-page size chunks, since
this makes it harder to place the pages on the destination.

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:27 +01:00
Dr. David Alan Gilbert 6c595cdee1 Page request: Process incoming page request
On receiving MIG_RPCOMM_REQ_PAGES look up the address and
queue the page.

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:27 +01:00
Dr. David Alan Gilbert 1e2d90ebc5 Page request: Add MIG_RP_MSG_REQ_PAGES reverse command
Add MIG_RP_MSG_REQ_PAGES command on Return path for the postcopy
destination to request a page from the source.

Two versions exist:
   MIG_RP_MSG_REQ_PAGES_ID that includes a RAMBlock name and start/len
   MIG_RP_MSG_REQ_PAGES that just has start/len for use with the same
                        RAMBlock as a previous MIG_RP_MSG_REQ_PAGES_ID

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:27 +01:00
Dr. David Alan Gilbert b10ac0c42c Postcopy: End of iteration
The end of migration in postcopy is a bit different since some of
the things normally done at the end of migration have already been
done on the transition to postcopy.

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:27 +01:00
Dr. David Alan Gilbert 1d34e4bf6a Postcopy: Postcopy startup in migration thread
Rework the migration thread to setup and start postcopy.

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:27 +01:00
Dr. David Alan Gilbert 1caddf8a81 postcopy: Incoming initialisation
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:27 +01:00
Dr. David Alan Gilbert e0b266f01d migration_completion: Take current state
Soon we'll be in either ACTIVE or POSTCOPY_ACTIVE when we
complete migration, and we need to know which we expect to be
in to change state safely.

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:27 +01:00
Dr. David Alan Gilbert 9ec055ae29 MIGRATION_STATUS_POSTCOPY_ACTIVE: Add new migration state
'MIGRATION_STATUS_POSTCOPY_ACTIVE' is entered after migrate_start_postcopy

'migration_in_postcopy' is provided for other sections to know if
they're in postcopy.

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:26 +01:00
Dr. David Alan Gilbert c31b098f64 Modify save_live_pending for postcopy
Modify save_live_pending to return separate postcopiable and
non-postcopiable counts.

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:26 +01:00
Dr. David Alan Gilbert 11cf1d984b MIG_CMD_PACKAGED: Send a packaged chunk of migration stream
MIG_CMD_PACKAGED is a migration command that wraps a chunk of migration
stream inside a package whose length can be determined purely by reading
its header.  The destination guarantees that the whole MIG_CMD_PACKAGED
is read off the stream prior to parsing the contents.

This is used by postcopy to load device state (from the package)
while leaving the main stream free to receive memory pages.

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:26 +01:00
Dr. David Alan Gilbert 093e3c4296 Add wrappers and handlers for sending/receiving the postcopy-ram migration messages.
The state of the postcopy process is managed via a series of messages;
   * Add wrappers and handlers for sending/receiving these messages
   * Add state variable that track the current state of postcopy

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:26 +01:00
Dr. David Alan Gilbert 7b89bf279f Rework loadvm path for subloops
Postcopy needs to have two migration streams loading concurrently;
one from memory (with the device state) and the other from the fd
with the memory transactions.

Split the core of qemu_loadvm_state out so we can use it for both.

Allow the inner loadvm loop to quit and cause the parent loops to
exit as well.

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:26 +01:00
Dr. David Alan Gilbert 70b2047774 Return path: Source handling of return path
Open a return path, and handle messages that are received upon it.

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:26 +01:00
Dr. David Alan Gilbert 6decec9311 Return path: Send responses from destination to source
Add migrate_send_rp_message to send a message from destination to source along the return path.
  (It uses a mutex to let it be called from multiple threads)
Add migrate_send_rp_shut to send a 'shut' message to indicate
  the destination is finished with the RP.
Add migrate_send_rp_ack to send a 'PONG' message in response to a PING
  Use it in the MSG_RP_PING handler

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:26 +01:00
Dr. David Alan Gilbert 2e37701efd Return path: Control commands
Add two src->dest commands:
   * OPEN_RETURN_PATH - To request that the destination open the return path
   * PING - Request an acknowledge from the destination

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:25 +01:00
Dr. David Alan Gilbert c76ca1888f Migration commands
Create QEMU_VM_COMMAND section type for sending commands from
source to destination.  These commands are not intended to convey
guest state but to control the migration process.

For use in postcopy.

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 15:00:25 +01:00
Dr. David Alan Gilbert a3e06c3d13 Rename save_live_complete to save_live_complete_precopy
In postcopy we're going to need to perform the complete phase
for postcopiable devices at a different point, start out by
renaming all of the 'complete's to make the difference obvious.

Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2015-11-10 14:51:49 +01:00
Peter Maydell 496c1b19fa * Guest ABI fixes for PC machines (hw_version)
* Fixes for recent Perl
 * John Snow's configure fixes
 * file-backed RAM improvements (Igor, Pavel)
 * -Werror=clobbered fixes (Stefan)
 * Kill -d ioport
 * Fix qemu-system-s390x
 * Performance improvement for kvmclock migration
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iQEcBAABAgAGBQJWO1zDAAoJEL/70l94x66DXRgH/ArIMi9MGU2Vxi6wNFG9hKUl
 Cl13IS8VO0ui6R/0F1BFGK90WYxfM5ZsVLPnTdk4OeapY6eKnw0O44VE0GqDZKFa
 k3B9qzQLGPLZV75cd8WP+ZHDbPcIgPecr8Jz3/w18rYIcGZQ6GF45xgdJ0hnYQ4j
 bQdEiseZyuPyeBU+f6cyNeD/nct4CehJWFwK+WwPc8C96tUIpVSJWwsiOf6NWvda
 KgSs1fCInw9e1//qCWWPxojEvTTW/JdmAOHyh9JTEpUezlXrDrRa5bDwng1VkVHM
 SZZ8H30GZmp/r9UH32TAlnxWvnRunE+uQVTyl3EAS6J7M+K+7fx2voBYSrN4dEY=
 =vr8Z
 -----END PGP SIGNATURE-----

Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging

* Guest ABI fixes for PC machines (hw_version)
* Fixes for recent Perl
* John Snow's configure fixes
* file-backed RAM improvements (Igor, Pavel)
* -Werror=clobbered fixes (Stefan)
* Kill -d ioport
* Fix qemu-system-s390x
* Performance improvement for kvmclock migration

# gpg: Signature made Thu 05 Nov 2015 13:42:27 GMT using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg:                 aka "Paolo Bonzini <pbonzini@redhat.com>"

* remotes/bonzini/tags/for-upstream:
  iscsi: Translate scsi sense into error code
  Revert "Introduce cpu_clean_all_dirty"
  kvmclock: add a new function to update env->tsc.
  configure: disable FORTIFY_SOURCE under clang
  backends/hostmem-file: Allow to specify full pathname for backing file
  configure: disallow ccache during compile tests
  cpu-exec: Fix compiler warning (-Werror=clobbered)
  memory: call begin, log_start and commit when registering a new listener
  megasas: Use qemu_hw_version() instead of QEMU_VERSION
  osdep: Rename qemu_{get, set}_version() to qemu_{, set_}hw_version()
  pc: Set hw_version on all machine classes
  qemu-log: remove -d ioport
  ioport: do not use CPU_LOG_IOPORT
  target-i386: fix pcmpxstrx equal-ordered (strstr) mode
  scripts/text2pod.pl: Escape left brace
  file_ram_alloc: propagate error to caller instead of terminating QEMU

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2015-11-05 14:31:24 +00:00
Gerd Hoffmann d2b90718d2 buffer: add tracing
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Peter Lieven <pl@kamp.de>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1446203414-4013-7-git-send-email-kraxel@redhat.com
2015-11-05 09:08:48 +01:00
Paolo Bonzini 6f94b7d97f ioport: do not use CPU_LOG_IOPORT
These messages are disabled by default; a perfect usecase for tracepoints,
which in fact already exist.  Add the missing information to them and
stop using qemu_log_mask.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-11-04 15:02:30 +01:00
Liang Li ea7415fac6 migration: rename qemu_savevm_state_cancel
The function qemu_savevm_state_cancel is called after the migration
in migration_thread, it seems strange to 'cancel' it after completion,
rename it to qemu_savevm_state_cleanup looks better.

Signed-off-by: Liang Li <liang.z.li@intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>al3
Reviewed-by: Amit Shah <amit.shah@redhat.com>al3
Signed-off-by: Juan Quintela <quintela@redhat.com>al3
2015-11-04 13:40:13 +01:00
Markus Armbruster 93f8f982fe monitor: Simplify event throttling
The event throttling state machine is hard to understand.  I'm not
sure it's entirely correct.  Rewrite it in a more straightforward
manner:

State 1: No event sent recently (less than evconf->rate ns ago)

    Invariant: evstate->timer is not pending, evstate->qdict is null

    On event: send event, arm timer, goto state 2

State 2: Event sent recently, no additional event being delayed

    Invariant: evstate->timer is pending, evstate->qdict is null

    On event: store it in evstate->qdict, goto state 3

    On timer: goto state 1

State 3: Event sent recently, additional event being delayed

    Invariant: evstate->timer is pending, evstate->qdict is non-null

    On event: store it in evstate->qdict, goto state 3

    On timer: send evstate->qdict, clear evstate->qdict,
              arm timer, goto state 2

Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1444921716-9511-3-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
2015-10-29 14:34:45 +01:00
Paolo Bonzini 659f7f6556 prep: do not use CPU_LOG_IOPORT, convert to tracepoints
These messages are disabled by default; a perfect usecase for tracepoints.
Convert them over.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
2015-10-23 12:38:28 +11:00
Marc-André Lureau 69b32a6ce4 net: add trace_vhost_user_event
Replace error_report() and use tracing instead. It's not an error to get
a connection or a disconnection, so silence this and trace it instead.

Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Thibaut Collet <thibaut.collet@6wind.com>
2015-10-22 14:34:49 +03:00
Peter Maydell c9003eb466 virtio-gpu: add 3d rendering support using virgl, misc fixes.
ui/gtk: add opengl context and scanout support (for virtio-gpu).
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iQIcBAABAgAGBQJWFjjrAAoJEEy22O7T6HE4DcoP/39p/sB46aGiIZI/5DieJVuS
 HGVKrNkOBEXBJItxgrC9z+ihcPE0F7sqkbalBZf/aJpQIszqwJraPKfZl2c63Uag
 fuJ3YGYh7MG3l601SUmPL3SwvaarBEn4pcChzv7lthLRHWWh0fA5sTAUECgKoZ/N
 TnLeCe+78Kn9LNqq4Cwib51H/b9Vijc8i04rsdc9okxoLA9QoRxl11nXkBY1RLnt
 rIUKMFGPegLxedDFdNi3gF7c5+vSw7u1xZvJK4vsSotoQaZxlHAqUR35w8ZH8TaE
 B7kTMD5cbF2hnJuaC33L/MfWTIED2Ru7LoQru91roW74tXP13o367jlT4jwD5MPb
 soxnJW+39Ipi8u8daZ9JzbQLR4l7tWi8SLFIMF2Vz1npPOGjjybhHl6DrHdo0X5w
 0IEZSN418GOYg76mX8mR1NEVIsAbx2EYGEJeuE/7vNmGipYr/eq8l5WqcqWZ2Iov
 2ZhqA1w+aopUJDA/M/iHFucb5vAq+Od6HnpCe3kB/kd7+1YPn1FE5gRfDC3BbRIQ
 qftYT4sVTHErJsLyOomd1YXSIMfbWXG9/CIEB4VZdKjYU0MJAIQbYbnUbKxhKRUa
 4CsnJYvMxYGpk9wYvHaM0Y7wRQFdfy8enTbs4Mte29ewRyc6YGcTnjAO+yeitLTn
 +k+Yp4qiwztkwVIEOlPn
 =cpgf
 -----END PGP SIGNATURE-----

Merge remote-tracking branch 'remotes/kraxel/tags/pull-virgl-20151008-1' into staging

virtio-gpu: add 3d rendering support using virgl, misc fixes.
ui/gtk: add opengl context and scanout support (for virtio-gpu).

# gpg: Signature made Thu 08 Oct 2015 10:35:39 BST using RSA key ID D3E87138
# gpg: Good signature from "Gerd Hoffmann (work) <kraxel@redhat.com>"
# gpg:                 aka "Gerd Hoffmann <gerd@kraxel.org>"
# gpg:                 aka "Gerd Hoffmann (private) <kraxel@gmail.com>"

* remotes/kraxel/tags/pull-virgl-20151008-1:
  gtk/opengl: add opengl context and scanout support (GtkGLArea)
  gtk/opengl: add opengl context and scanout support (egl)
  opengl: add egl-context.[ch] helpers
  virtio-gpu: add cursor update tracepoint
  virtio-gpu: add 3d mode and virgl rendering support.
  virtio-gpu: update headers for virgl/3d
  virtio-gpu: change licence from GPLv2 to GPLv2+
  virtio-gpu: move iov free to virtio_gpu_cleanup_mapping_iov
  ui/console: add opengl context and scanout support interfaces.
  sdl2: stop flickering
  shaders: initialize vertexes once

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2015-10-09 17:30:03 +01:00