this function search the capability from the end, the last
size should 0x100 - pos, not 0xff - pos.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-22-git-send-email-peter.maydell@linaro.org
The PCI spec recommends devices use additional alignment for MSI-X
data structures to allow software to map them to separate processor
pages. One advantage of doing this is that we can emulate those data
structures without a significant performance impact to the operation
of the device. Some devices fail to implement that suggestion and
assigned device performance suffers.
One such case of this is a Mellanox MT27500 series, ConnectX-3 VF,
where the MSI-X vector table and PBA are aligned on separate 4K
pages. If PBA emulation is enabled, performance suffers. It's not
clear how much value we get from PBA emulation, but the solution here
is to only lazily enable the emulated PBA when a masked MSI-X vector
fires. We then attempt to more aggresively disable the PBA memory
region any time a vector is unmasked. The expectation is then that
a typical VM will run entirely with PBA emulation disabled, and only
when used is that emulation re-enabled.
Reported-by: Shyam Kaushik <shyam.kaushik@gmail.com>
Tested-by: Shyam Kaushik <shyam.kaushik@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
For quirks that support the full PCIe extended config space, limit the
quirk to only the size of config space available through vfio. This
allows host systems with broken MMCONFIG regions to still make use of
these quirks without generating bad address faults trying to access
beyond the end of config space exposed through vfio. This may expose
direct access to the mirror of extended config space, only trapping
the sub-range of standard config space, but allowing this makes the
quirk, and thus the device, functional. We expect that only device
specific accesses make use of the mirror, not general extended PCI
capability accesses, so any virtualization in this space is likely
unnecessary anyway, and the device is still IOMMU isolated, so it
should only be able to hurt itself through any bogus configurations
enabled by this space.
Link: https://www.redhat.com/archives/vfio-users/2015-November/msg00192.html
Reported-by: Ronnie Swanink <ronnie@ronnieswanink.nl>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
g_new(T, n) is neater than g_malloc(sizeof(T) * n). It's also safer,
for two reasons. One, it catches multiplication overflowing size_t.
Two, it returns T * rather than void *, which lets the compiler catch
more type errors.
This commit only touches allocations with size arguments of the form
sizeof(T). Same Coccinelle semantic patch as in commit b45c03f.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When we have a PCIe VM, such as Q35, guests start to care more about
valid configurations of devices relative to the VM view of the PCI
topology. Windows will error with a Code 10 for an assigned device if
a PCIe capability is found for a device on a conventional bus. We
also have the possibility of IOMMUs, like VT-d, where the where the
guest may be acutely aware of valid express capabilities on physical
hardware.
Some devices, like tg3 are adversely affected by this due to driver
dependencies on the PCIe capability. The only solution for such
devices is to attach them to an express capable bus in the VM.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In-kernel ITS emulation on ARM64 will require to supply requester IDs.
These IDs can now be retrieved from the device pointer using new
pci_requester_id() function.
This patch adds pci_dev pointer to KVM GSI routing functions and makes
callers passing it.
x86 architecture does not use requester IDs, but hw/i386/kvm/pci-assign.c
also made passing PCI device pointer instead of NULL for consistency with
the rest of the code.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Message-Id: <ce081423ba2394a4efc30f30708fca07656bc500.1444916432.git.p.fedin@samsung.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
At present the memory listener used by vfio to keep host IOMMU mappings
in sync with the guest memory image assumes that if a guest IOMMU
appears, then it has no existing mappings.
This may not be true if a VFIO device is hotplugged onto a guest bus
which didn't previously include a VFIO device, and which has existing
guest IOMMU mappings.
Therefore, use the memory_region_register_iommu_notifier_replay()
function in order to fix this case, replaying existing guest IOMMU
mappings, bringing the host IOMMU into sync with the guest IOMMU.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Depending on the host IOMMU type we determine and record the available page
sizes for IOMMU translation. We'll need this for other validation in
future patches.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The current vfio core code assumes that the host IOMMU is capable of
mapping any IOVA the guest wants to use to where we need. However, real
IOMMUs generally only support translating a certain range of IOVAs (the
"DMA window") not a full 64-bit address space.
The common x86 IOMMUs support a wide enough range that guests are very
unlikely to go beyond it in practice, however the IOMMU used on IBM Power
machines - in the default configuration - supports only a much more limited
IOVA range, usually 0..2GiB.
If the guest attempts to set up an IOVA range that the host IOMMU can't
map, qemu won't report an error until it actually attempts to map a bad
IOVA. If guest RAM is being mapped directly into the IOMMU (i.e. no guest
visible IOMMU) then this will show up very quickly. If there is a guest
visible IOMMU, however, the problem might not show up until much later when
the guest actually attempt to DMA with an IOVA the host can't handle.
This patch adds a test so that we will detect earlier if the guest is
attempting to use IOVA ranges that the host IOMMU won't be able to deal
with.
For now, we assume that "Type1" (x86) IOMMUs can support any IOVA, this is
incorrect, but no worse than what we have already. We can't do better for
now because the Type1 kernel interface doesn't tell us what IOVA range the
IOMMU actually supports.
For the Power "sPAPR TCE" IOMMU, however, we can retrieve the supported
IOVA range and validate guest IOVA ranges against it, and this patch does
so.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
If a DMA mapping operation fails in vfio_listener_region_add() it
checks to see if we've already completed initial setup of the
container. If so it reports an error so the setup code can fail
gracefully, otherwise throws a hw_error().
There are other potential failure cases in vfio_listener_region_add()
which could benefit from the same logic, so move it to its own
fail: block. Later patches can use this to extend other failure cases
to fail as gracefully as possible under the circumstances.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Currently the VFIOContainer iommu_data field contains a union with
different information for different host iommu types. However:
* It only actually contains information for the x86-like "Type1" iommu
* Because we have a common listener the Type1 fields are actually used
on all IOMMU types, including the SPAPR TCE type as well
In fact we now have a general structure for the listener which is unlikely
to ever need per-iommu-type information, so this patch removes the union.
In a similar way we can unify the setup of the vfio memory listener in
vfio_connect_container() that is currently split across a switch on iommu
type, but is effectively the same in both cases.
The iommu_data.release pointer was only needed as a cleanup function
which would handle potentially different data in the union. With the
union gone, it too can be removed.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In irqfd mode, current code attempts to set a resamplefd whatever
the type of the IRQ. For an edge-sensitive IRQ this attempt fails
and as a consequence, the whole irqfd setup fails and we fall back
to the slow mode. This patch bypasses the resamplefd setting for
non level-sentive IRQs.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
unmask EventNotifier might not be initialized in case of edge
sensitive irq. Using EventNotifier pointers make life simpler to
handle the edge-sensitive irqfd setup.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
With current implementation, eventfd VFIO signaling is first set up and
then irqfd is setup, if supported and allowed.
This start sequence causes several issues with IRQ forwarding setup
which, if supported, is transparently attempted on irqfd setup:
IRQ forwarding setup is likely to fail if the IRQ is detected as under
injection into the guest (active at irqchip level or VFIO masked).
This currently always happens because the current sequence explicitly
VFIO-masks the IRQ before setting irqfd.
Even if that masking were removed, we couldn't prevent the case where
the IRQ is under injection into the guest.
So the simpler solution is to remove this 2-step startup and directly
attempt irqfd setup. This is what this patch does.
Also in case the eventfd setup fails, there is no reason to go farther:
let's abort.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Specifying an emulated PCI vendor/device ID can be useful for testing
various quirk paths, even though the behavior and functionality of
the device with bogus IDs is fully unsupportable. We need to use a
uint32_t for the vendor/device IDs, even though the registers
themselves are only 16-bit in order to be able to determine whether
the value is valid and user set.
The same support is added for subsystem vendor/device ID, though these
have the possibility of being useful and supported for more than a
testing tool. An emulated platform might want to impose their own
subsystem IDs or at least hide the physical subsystem ID. Windows
guests will often reinstall drivers due to a change in subsystem IDs,
something that VM users may want to avoid. Of course careful
attention would be required to ensure that guest drivers do not rely
on the subsystem ID as a basis for device driver quirks.
All of these options are added using the standard experimental option
prefix and should not be considered stable.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Simplify access to commonly referenced PCI vendor and device ID by
caching it on the VFIOPCIDevice struct.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This is just another quirk, for reset rather than affecting memory
regions. Move it to our new quirks file.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Config windows make use of an address register and a data register.
In VGA cards, these are often used to provide real mode code in the
BIOS an easy way to access MMIO registers since the window often
resides in an I/O port register. When the MMIO register has a mirror
of PCI config space, we need to trap those accesses and redirect them
to emulated config space.
The previous version of this functionality made use of a single
MemoryRegion and single match address. This version uses separate
MemoryRegions for each of the address and data registers and allows
for multiple match addresses. This is useful for Nvidia cards which
have two ranges which index into PCI config space.
The previous implementation is left for the follow-on patch for a more
reviewable diff.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Another rework of this quirk, this time to update to the new quirk
structure. We can handle the address and data registers with
separate MemoryRegions and a quirk specific data structure, making the
code much more understandable.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The Nvidia 0x3d0 quirk makes use of a two separate registers and gives
us our first chance to make use of separate memory regions for each to
simplify the code a bit.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This is an easy quirk that really doesn't need a data structure if
its own. We can pass vdev as the opaque data and access to the
MemoryRegion isn't required.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
VFIOQuirk hosts a single memory region and a fixed set of data fields
that try to handle all the quirk cases, but end up making those that
don't exactly match really confusing. This patch introduces a struct
intended to provide more flexibility and simpler code. VFIOQuirk is
stripped to its basics, an opaque data pointer for quirk specific
data and a pointer to an array of MemoryRegions with a counter. This
still allows us to have common teardown routines, but adds much
greater flexibility to support multiple memory regions and quirk
specific data structures that are easier to maintain. The existing
VFIOQuirk is transformed into VFIOLegacyQuirk, which further patches
will eliminate entirely.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Create a vendor:device ID helper that we'll also use as we rework the
rest of the quirks. Re-reading the config entries, even if we get
more blacklist entries, is trivial overhead and only incurred during
device setup. There's no need to typedef the blacklist structure,
it's a static private data type used once. The elements get bumped
up to uint32_t to avoid future maintenance issues if PCI_ANY_ID gets
used for a blacklist entry (avoiding an actual hardware match). Our
test loop is also crying out to be simplified as a for loop.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The default should be to allow mmap and new drivers shouldn't need to
expose an option or set it to other than the allocation default in
their initfn. Take advantage of the experimental flag to change this
option to the correct polarity.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Tracing is more effective when we can completely disable all KVM
bypass paths. Make these runtime rather than build-time configurable.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This allows vfio_msi* tracing. The MSI/X interrupt tracing is also
pulled out of #ifdef DEBUG_VFIO to avoid a recompile for tracing this
path. A few cycles to read the message is hardly anything if we're
already in QEMU.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Rename functions and tracing callbacks so that we can trace vfio_intx*
to see all the INTx related activities.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
With the addition of the Chelsio quirk we have an error path out of
vfio_early_setup_msix() that doesn't free the allocated VFIOMSIXInfo
struct. This doesn't introduce a leak as it still gets freed in the
vfio_put_device() path, but it's complicated and sloppy to rely on
that. Restructure to free the allocated data on error and only link
it into the vdev on success.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reported-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
There's quite a bit of cleanup that can be done to the RTL8168 quirk,
as well as the tracing to prevent a spew of uninteresting accesses
for anything else the driver might choose to use the window registers
for besides the MSI-X table. There should be no functional change,
but it's now possible to get compact and useful traces by enabling
vfio_rtl8168_quirk*, ex:
vfio_rtl8168_quirk_write 0000:04:00.0 [address]: 0x1f000
vfio_rtl8168_quirk_read 0000:04:00.0 [address]: 0x8001f000
vfio_rtl8168_quirk_read 0000:04:00.0 [data]: 0xfee0100c
vfio_rtl8168_quirk_write 0000:04:00.0 [address]: 0x1f004
vfio_rtl8168_quirk_read 0000:04:00.0 [address]: 0x8001f004
vfio_rtl8168_quirk_read 0000:04:00.0 [data]: 0x0
vfio_rtl8168_quirk_write 0000:04:00.0 [address]: 0x1f008
vfio_rtl8168_quirk_read 0000:04:00.0 [address]: 0x8001f008
vfio_rtl8168_quirk_read 0000:04:00.0 [data]: 0x49b1
vfio_rtl8168_quirk_write 0000:04:00.0 [address]: 0x1f00c
vfio_rtl8168_quirk_read 0000:04:00.0 [address]: 0x8001f00c
vfio_rtl8168_quirk_read 0000:04:00.0 [data]: 0x0
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Minor cleanup.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
A number of files were including dirent.h but not using any
of the functions it provides
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Many source files have doubled words (eg "the the", "to to",
and so on). Most of these can simply be removed, but a couple
were actual mis-spellings (eg "to to" instead of "to do").
There was even one triple word score "to to to" :-)
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
bootindex was incorrectly changed to a device Property during the
platform code split, resulting in it no longer working. Remove it.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: qemu-stable@nongnu.org # v2.3+
The RTL8168 quirk correctly describes using bit 31 as a signal to
mark a latch/completion, but the code mistakenly uses bit 28. This
causes the Realtek driver to spin on this register for quite a while,
20k cycles on Windows 7 v7.092 driver. Then it gets frustrated and
tries to set the bit itself and spins for another 20k cycles. For
some this still results in a working driver, for others not. About
the only thing the code really does in its current form is protect
the guest from sneaking in writes to the real hardware MSI-X table.
The fix is obviously to use bit 31 as we document that we should.
The other problem doesn't seem to affect current drivers as nobody
seems to use these window registers for writes to the MSI-X table, but
we need to use the stored data when a write is triggered, not the
value of the current write, which only provides the offset.
Note that only the Windows drivers from Realtek seem to use these
registers, the Microsoft drivers provided with Windows 8.1 do not
access them, nor do Linux in-kernel drivers.
Link: https://bugs.launchpad.net/qemu/+bug/1384892
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: qemu-stable@nongnu.org # v2.1+
Fix pba_offset initialization value for Chelsio T5 Virtual Function
device. The T5 hardware has a bug in it where it reports a Pending Interrupt
Bit Array Offset of 0x8000 for its SR-IOV Virtual Functions instead
of the 0x1000 that the hardware actually uses internally. As the hardware
doesn't return the correct pba_offset value, add a quirk to instead
return a hardcoded value of 0x1000 when a Chelsio T5 VF device is
detected.
This bug has been fixed in the Chelsio's next chip series T6 but there are
no plans to respin the T5 ASIC for this bug. It is just documented in the
T5 Errata and left it at that.
Signed-off-by: Gabriel Laupre <glaupre@chelsio.com>
Reviewed-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
On systems with guest visible IOMMU, adding a new memory region onto
PCI bus calls vfio_listener_region_add() for every DMA window. This
installs a notifier for IOMMU memory regions. The notifier is supposed
to be removed vfio_listener_region_del(), however in the case of mixed
PHB (emulated + VFIO devices) when last VFIO device is unplugged and
container gets destroyed, all existing DMA windows stay alive altogether
with the notifiers which are on the linked list which head was in
the destroyed container.
This unregisters IOMMU memory region notifier when a container is
destroyed.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch aims at optimizing IRQ handling using irqfd framework.
Instead of handling the eventfds on user-side they are handled on
kernel side using
- the KVM irqfd framework,
- the VFIO driver virqfd framework.
the virtual IRQ completion is trapped at interrupt controller
This removes the need for fast/slow path swap.
Overall this brings significant performance improvements.
Signed-off-by: Alvise Rigo <a.rigo@virtualopensystems.com>
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Vikram Sethi <vikrams@codeaurora.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Anticipating for the introduction of new add/remove functions taking
a qemu_irq parameter, let's rename existing ones with a gsi suffix.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Vikram Sethi <vikrams@codeaurora.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This is system level code, and should only depend on the host page
size, not the target page size.
Note that HOST_PAGE_SIZE is misleadingly lead and is really aligning
to both host and target page size. Hence it's replacement with
REAL_HOST_PAGE_SIZE.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
size_t is an unsigned type, thus the error case is never reached in
the below call to pread. If bytes is negative, it will be seen as
a very high positive value.
Spotted by Coverity.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Include linux/vfio.h after sys/ioctl.h, just like in hw/vfio/common.c.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-id: 1434544500-22405-1-git-send-email-leon.alrae@imgtec.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
g_malloc0_n() is introduced since glib-2.24 while QEMU currently
requires glib-2.22. This may cause a link error on some distributions.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The platform device class has become abstract. This patch introduces
a calxeda xgmac device that derives from it.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch adds the code requested to assign interrupts to
a guest. The interrupts are mediated through user handled
eventfds only.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Vikram Sethi <vikrams@codeaurora.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Minimal VFIO platform implementation supporting register space
user mapping but not IRQ assignment.
Signed-off-by: Kim Phillips <kim.phillips@linaro.org>
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Vikram Sethi <vikrams@codeaurora.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Once address_space_translate will be called outside the BQL, the returned
MemoryRegion might disappear as soon as the RCU read-side critical section
ends. Avoid this by moving the critical section to the callers.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1426684909-95030-3-git-send-email-pbonzini@redhat.com>
Somehow these GPUs manage not to respond to a PCI bus reset, removing
our primary mechanism for resetting graphics cards. The result is
that these devices typically work well for a single VM boot. If the
VM is rebooted or restarted, the guest driver is not able to init the
card from the dirty state, resulting in a blue screen for Windows
guests.
The workaround is to use a device specific reset. This is not 100%
reliable though since it depends on the incoming state of the device,
but it substantially improves the usability of these devices in a VM.
Credit to Alex Deucher <alexander.deucher@amd.com> for his guidance.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This is an impossible error path due to the fact that we're reading a
kernel provided, rather than user provided link, which will certainly
always fit in PATH_MAX. Currently it returns a fixed 26 char path
plus %d group number, which typically maxes out at double digits.
However, the caller of the initfn certainly expects a less-than zero
return value on error, not just a non-zero value. Therefore we
should correct the sign here.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In an analysis by Laszlo, the resulting type of our calculation for
the end of the MSI-X table, and thus the start of memory after the
table, is uint32_t. We're therefore not correctly preventing the
corner case overflow that we intended to fix here where a BAR >=4G
could place the MSI-X table to end exactly at the 4G boundary. The
MSI-X table offset is defined by the hardware spec to 32bits, so we
simply use a cast rather than changing data structure types. This
scenario is purely theoretically, typically the MSI-X table is located
at the front of the BAR.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Rather than retaining io_mem_read/write as simple wrappers around
the memory_region_dispatch_read/write functions, make the latter
public and change all the callers to use them, since we need to
touch all the callsites anyway to add MemTxAttrs and MemTxResult
support. Delete io_mem_read and io_mem_write entirely.
(All the callers currently pass MEMTXATTRS_UNSPECIFIED
and convert the return value back to bool or ignore it.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The patch implements sPAPRPHBClass EEH callbacks so that the EEH
RTAS requests can be routed to VFIO for further handling.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Linux v4.0-rc1 vfio-pci introduced a new virtual interrupt to allow
the kernel to request a device from the user. When signaled, QEMU
will by default attmempt to hot-unplug the device. This is a one-
shot attempt with the expectation that the kernel will continue to
poll for the device if it is not returned. Returning the device when
requested is the expected standard model of cooperative usage, but we
also add an option option to disable this feature. Initially this
opt-out is set as an experimental option because we really should
honor kernel requests for the device.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Disabling MMAP support uses the slower read/write accesses but allows to
trace all MMIO accesses, which is not good for performance, but very
useful for reverse engineering PCI drivers. This option allows to
disable MMAP per device without a compile-time change.
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
They are not used from anywhere but common.c which is where these are
defined so make them static.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This makes the error report more informative.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This fixes a compiler error which occurs if DEBUG_VFIO is defined.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The difference between v1 and v2 is fairly subtle, simply more
deterministic behavior for unmaps. The v1 interface allows the user
to attempt to unmap sub-regions of previous mappings, returning
success with zero size if unable to comply. This was a reflection of
the underlying IOMMU API. The v2 interface requires that the user
may only unmap fully contained mappings, ie. an unmap cannot intersect
or bisect a previous mapping, but may cover multiple mappings. QEMU
never made use of the sub-region v1 support anyway, so we can support
either v1 or v2. We'll favor v2 since it's newer.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In the case of VFIO, the unrealize callback is too early to munmap the
BARs. The munmap must be delayed until memory accesses are complete.
To do this, split vfio_unmap_bars in two. The removal step, now called
vfio_unregister_bars, remains in vfio_exitfn. The reclamation step
is vfio_unmap_bars and is moved to the instance_finalize callback.
Similarly, quirk MemoryRegions have to be removed during
vfio_unregister_bars, but freeing the data structure must be delayed
to vfio_unmap_bars.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In order to enable out-of-BQL address space lookup, destruction of
devices needs to be split in two phases.
Unrealize is the first phase; once it complete no new accesses will
be started, but there may still be pending memory accesses can still
be completed.
The second part is freeing the device, which only happens once all memory
accesses are complete. At this point the reference count has dropped to
zero, an RCU grace period must have completed (because the RCU-protected
FlatViews hold a reference to the device via memory_region_ref). This is
when instance_finalize is called.
Freeing data belongs in an instance_finalize callback, because the
dynamically allocated memory can still be used after unrealize by the
pending memory accesses.
This starts the process by creating an instance_finalize callback and
freeing most of the dynamically-allocated data in instance_finalize.
Because instance_finalize is also called on error paths or also when
the device is actually not realized, the common code needs some changes
to be ready for this. The error path in vfio_initfn can be simplified too.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Now that vfio_put_base_device is called unconditionally at instance_finalize
time, it can be called twice if vfio_populate_device fails. This works
but it is slightly harder to follow.
Change vfio_get_device to not touch the vbasedev struct until it will
definitely succeed, moving the vfio_populate_device call back to vfio-pci.
This way, vfio_put_base_device will only be called once.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Commit d8d9581460 added explicit object_unparent() calls for
dynamically allocated MemoryRegions. The VFIOMSIXInfo structure also
contains such a MemoryRegion, covering the mmap'd region of a PCI BAR
above the MSI-X table. This structure is freed as part of the class
exit function and therefore also needs an explicit object_unparent().
Failing to do this results in random segfaults due to fields within
the structure, often the class pointer, being reclaimed and corrupted
by the time object_finalize_child_property() is called for the object.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: qemu-stable@nongnu.org # 2.2
When disabling MSI/X interrupts the disable functions will leave the
device in INTx mode (when available). This matches how hardware
operates, INTx is enabled unless MSI/X is enabled (DisINTx is handled
separately). Therefore when we really want to disable all interrupts,
such as when removing the device, and we start with the device in
MSI/X mode, we need to pass through INTx on our way to being
completely quiesced.
In well behaved situations, the guest driver will have shutdown the
device and it will start vfio_exitfn() in INTx mode, producing the
desired result. If hot-unplug causes the guest to crash, we may get
the device in MSI/X state, which will leave QEMU with a bogus handler
installed.
Fix this by re-ordering our disable routine so that it should always
finish in VFIO_INT_NONE state, which is what all callers expect.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
We use an unsigned int when working with the PCI BAR size, which can
obviously overflow if the BAR is 4GB or larger. This needs to change
to a fixed length uint64_t. A similar issue is possible, though even
more unlikely, when mapping the region above an MSI-X table. The
start of the MSI-X vector table must be below 4GB, but the end, and
therefore the start of the next mapping region, could still land at
4GB.
Suggested-by: Nishank Trivedi <nishank.trivedi@netapp.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Don Slutz <dslutz@verizon.com>
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
With the conversion to tracepoints, a couple previous DPRINTKs are
now quite a bit more visible and are really just informational.
Remove these and add a bit more description to another.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
A new common module is created. It implements all functions
that have no device specificity (PCI, Platform).
This patch only consists in move (no functional changes)
Signed-off-by: Kim Phillips <kim.phillips@linaro.org>
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
vfio_get_device now takes a VFIODevice as argument. The function is split
into 2 parts: vfio_get_device which is generic and vfio_populate_device
which is bus specific.
3 new fields are introduced in VFIODevice to store dev_info.
vfio_put_base_device is created.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This structure is going to be shared by VFIOPCIDevice and
VFIOPlatformDevice. VFIOBAR includes it.
vfio_eoi becomes an ops of VFIODevice specialized by parent device.
This makes possible to transform vfio_bar_write/read into generic
vfio_region_write/read that will be used by VFIOPlatformDevice too.
vfio_mmap_bar becomes vfio_map_region
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Since we can potentially have both PCI and platform devices in
the same VFIO group, this latter now owns a list of VFIODevices.
A unified reset handler, vfio_reset_handler, is registered, looping
through this VFIODevice list. 2 specialized operations are introduced
(vfio_compute_needs_reset and vfio_hot_reset_multi): they allow to
implement type specific behavior. also reset_works and needs_reset
VFIOPCIDevice fields are moved into VFIODevice.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Add 3 new fields in the VFIODevice struct. Type is set to
VFIO_DEVICE_TYPE_PCI. The type enum value will later be used
to discriminate between VFIO PCI and platform devices. The name is
set to domain🚌slot:function. Currently used to test whether
the device already is attached to the group. Later on, the name
will be used to simplify all traces. The group is simply moved
from VFIOPCIDevice to VFIODevice.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
[Fix g_strdup_printf() usage]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Introduce a new base VFIODevice strcut that will be used by both PCI
and Platform VFIO device. Move VFIOPCIDevice fd field there. Obviously
other fields from VFIOPCIDevice will be moved there but this patch
file is introduced to ease the review.
Also vfio_mask_single_irqindex, vfio_unmask_single_irqindex,
vfio_disable_irqindex now take a VFIODevice handle as argument.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
To prepare for platform device introduction, rename vfio_mask_intx
and vfio_unmask_intx into vfio_mask_single_irqindex and respectively
unmask_single_irqindex. Also use a nex index parameter.
With that name and prototype the function will be usable for other
indexes than VFIO_PCI_INTX_IRQ_INDEX.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This prepares for the introduction of VFIOPlatformDevice
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This is done in preparation for the addition of VFIO platform
device support.
Signed-off-by: Kim Phillips <kim.phillips@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
